Professional Documents
Culture Documents
Syllabus:
Chapter- 1:
1. Introduction To Structural Engineering
2. What is a Structure?
3. About STAAD.Pro V8i
4. Getting Started
Chapter- 2:
1. Starting STAAD.Pro V8i
2. Methods Of Model Generation
3. Translational Repeat
4. Circular Repeat
5. Insert Node
6. Add Beam
Chapter- 3:
1. Run Structure Wizard
2. Generation Structure Models
3. Merging the Generated Model in STAAD.Pro
4. Importing CAD Models
Chapter- 4:
1. Support Specification
2. Support Page
3. Member Property
4. Member Offset
Chapter- 5:
1. Loading 1
2. Loading 2
3. Wind Load Generation
4. Assigning Wind Loads
Chapter- 5:
1. Analysis
2. Concrete Design
3. Time History Analysis
Chapter- 6:
1. Introduction to FEM
2. Plate
3. Surface
4. Meshing
Chapter- 7: (Slabs)
1. Desgin Of Slab
2. Design Of One Way Slab
3. Design Of Two Way Slab
4. Design Of Staircase
5. Design of Bridge using STAAD .Beava
Chapter- 8: (Bridge Deck Preprocessor Worked Example)
1. Bridge Deck Preprocessing Using STAAD.Beava
Chapter- 9: (Steel)
1. Design Of Steel Structures
2. Member Specification
Table Member Property
Chapter- 10: (Seismic Loads Worked Examples)
1. Calculate Natural Frequency of a Building By Response Spectrum Analysis
2. Calculate Natural Frequency of a Building By Rayleigh Method
3. Calculate Natural Frequency of a Building By Modal Shape
Chapter- 11: (Wind Load Intensity Worked Examples)
Calculate Wind Load Intensity In a Building
Chapter- 1:
1. Introduction To Structural Engineering
2. What is a Structure?
3. About STAAD.Pro V8i
4. Getting Started
codes.
2.What is a Structure?
A Structure can be defined as an interrelated or independent parts forming a more complex,
unified whole and serving a common purpose. For instance, a building can be defined as a
structural system designed and constructed to support and transmit applied lateral and
gravity loads safely to the ground without exceeding the allowable stresses in its members.
The super structure is the vertical extension of the building above the foundation. Columns,
beams and load bearing wall support floors and roof structures. The substructure is the
underlying structure forming the foundation of the building.
Types of Structures:
1. Space Structure:
2. Plane Structure:
Suitable only for two dimensional modes in x y plane with no loading or distortions
upright to this plane.
3. Truss Structure:
Allows loading in any direction, but members only deliver axial resistance. Members
dismiss resist bending or shear loads.
4. Floor Structure:
Suitable for two dimensional models in x z plane with loading and distortions
perpendicular to this plane.
STAAD.Pro is a overall resolution program for execution of analysis and design of a extensive
variation of types of structures. The simple three activities which are to be carried out to
accomplish that goal a) model generation,
Nodes
Nodes:
Stiffed Joint with 6 reactions. It is located at each end of the Beam and each corner of the
Plate Nodes considered the essence of the geometry of any structure in STAAD.Pro. Each
node holds the following informations:
Node Number.
Beam:
Any member in the structure, that can be beam, column, bracing member or truss member.
Beams are actually defined based on the Nodes at their ends. Each beam holds the following
information:
Beam Number.
Plates:
A thin shell with 4 node shaped element. It can be slab or wall element. Each plate will holds
the following information:
Plate Number.
Surface:
A thin shell in green color with mutli-nodded shape starting from 3 nodes and more. It can
be anything of slabs, walls and raft foundations. It holds the following information:
Surface Number.
Hardware Requirements:
The following requirements are suggested minimums. Systems with increased capacity
provide enhanced performance.
Graphics card and monitor with 1024768 resolution, 256 color display (16 bit high
color recommended).
Sufficient free space on the hard disk to hold the program and data files. The disk
space requirement will vary depending on the modules you are installing. A typical
minimum is 500MB free space.
A multi-media ready system with sound card and speakers is needed to run the
tutorial movies and slide shows.
Chapter- 2:
1. Starting STAAD.Pro V8i
2. Methods Of Model Generation
3. Translational Repeat
4. Circular Repeat
5. Insert Node
6. Add Beam
3. Before starting a project, you must be aware of the type of structure. The structure type
can be defined as Space, Plane, Floor, or Truss.
Plane: The type of geometry, loading and deformation are restricted to the global X-Y
plane only.
Truss: The structure transmits loading by pure axial action. Truss members are
considered to be in capable of carrying shear, bending and torsion.
4. Set the length units and loading units and click Next button.
Note: The units can be altered later if needed, at any point of the model creation.
5. Now Where do you want to go? dialog box appears. You have specify the method for
building
Add Beam: Sets the program in the Snap Node/Beam dialog and snap grid to
construct your model by creating new joints and beams using the construction grid,
drawing tools and spreadsheets.
Add Plate: Sets the program up with the Snap Node/Plate dialog to construct your
model by creating new joints and 3-noded and 4-noded plate elements using the
construction grid, drawing tools and spreadsheets.
Add Solid: Sets the program up with the Snap Node/Plate dialog to
construct your model by creating new joints and 8-noded solid/brick elements using the
construction grid, drawing tools and spreadsheets.
Open Structure Wizard: Opens the library of readymade structure templates which
can be extracted and modified parametric model standard, parametric structural
templates for trusses, surfaces, bay frames and much more.
Open STAAD.Editor: Allows you to build your model using STAAD syntax commands
(non-graphical interface) through the STAAD editor.
Edit Job Information: Automatically opens the Job Information dialog box which
provide information about the job (i.e. clients name, job title, engineers involved, etc.)
before building your model.
2. Methods Of Model Generation
Pre Processor: Generates the model with all the data needed for the analysis.
Creating Nodes:
When you select the Nodes command in geometry menu, it shows a dialog box where you
can enter the joint coordinates.
After creating the joint i.e. entering the coordinates, you can able to see the joint in the
modelling area.
JOINT COORDINATES
i1, x1, y1, z1, (i2, x2, y2, z2, i3)
REPEAT n, xi,yi1, zi1, (xi1, yi2, . . . . xin, yin, zin)
REPEAT ALL n,xi1, yi1, zi1, (xi2, yi2, zi2, . . . . xin, yin, zin)
Beams, plates and 8 nodes solid element can be created using the suitable Snap/Grid tool.
When this function is propelled, the following dialog is opened which includes a Default Grid.
This grid will be of type linear, there are also options to create Radial, and Irregular grids.
As new grids are added or modified, the information is stored in the STAAD.Pro data folder
with a GRD allowance that permits other STAAD.Pro file to re-use these defined grids. To
alter the starting of this grid, click on the Edit button to show the existing grid properties.
The current plane of the grid is set by selecting the required option. This can rotated about
one of the global planes by selecting the axis of rotation and setting the angle.
The origin of the grid is marked on the graphics, with a small circle. The location of the
origin, specified in global coordinates, can either be defined explicitly in the given X.Y and Z
coordinates, or it can be set to the coordinates of an existing node by clicking on the icon
and then on the node itself in the graphical window. Note that at this point the origin
coordinate is updated.
The construction lines are used to specify how many gridlines are created either side of the
origin, the spacing between the gridlines and if there should be a skew in degrees along
either axis.
Click on the OK button to accept these settings.
Additional grids can be defined by clicking in the Create button. Three different types of
standard grid can be created:
Linear
Radial
Irregular
The type of the grid required can be selected from the drop down list available at the top of
the property sheet.
Each new grid should be identified with a unique name for future reference. The functionality
for each type of grid is given below:
Linear:
Location of the origin can be defined with respect to global X, Y and Z coordinates
systems.
Radial:
Plane is defined as being coincident with the global XY, XZ and YZ planes or at angle
skewed with respect to the global planes.
Location of the origin can be defined with respect to global X, Y and Z coordinates
systems.
Well suited for drawing circular models using piece-wise linear techniques.
The settings for a Radial grid are defined in the following window:
The Plane, Angle of Plane and Grid origin option are as for the linear.
Irregular:
The settings for an irregular grid are defined in the following window:
3. Translational Repeat
Translational Option allows to copy the entire structure or a portion of the structure in a
linear direction. We may generate one or more several copies of the selected components.
Select the structural elements to repeat. Select Geometry Translational Repeat option from
the geometry menu or Click Translational Repeat Icon
box appears as shown below:
Global Direction:
Choose any one of the three possible global direction along which the selected structural
elements should be copies.
No of Steps:
Specify the numbers of steps to repeated you need.
Default Step Spacing:
Type the default spacing between steps in the edit box in current length units. For each step,
the default value of the spacing will be what we provide in the Default step spacing box. We
can change the spacing of individual steps if we choose to do so.
Step Spacing Table:
This table consists of two columns: Step and Spacing. We can change the spacing of any
type in the table.
Renumber Bay:
This is the way of instructing the program to use a user-specified starting number for the
members generated in each step of the translational repeat activity.
Geometry Only:
The Translational Repeat allows the copying of the elements without having their loads
properties, steel design parameters, etc. being copied with it. By default (when the
Geometry Only option is not checked) all loads, properties, design parameters, members
releases, etc. on the selected elements will automatically be copied along with the elements.
By checking the option labelled Geometry Only, the translational repeating will be per
formed using only geometry data.
Link Steps and Open Base:
If you want to automatically connect the steps or copies by new members, along the
specified global directions, check the Link Steps check box. In other words, the Link Steps
option is applicable when the newly created units are physically removed from the existing
units and when one wishes to connect those using members. To avoid joining the base of the
copied structures, check the Open Base box.
Here you can see the Frame model copied using the Translational Repeat option:
4. Circular Repeat
Circular Repeat allows to copy of the entire structure on an portion of if in a circular
direction. Select the structural elements to repeat and select the Circular Repeat option from
the geometry menu. The 3D Circular dialog box appears as shown in the figure.
Axis of Rotation:
Click the radio button to choose the axis of rotation for repeating the selected components.
Through:
The new highlight node button selects the Node on Plane. Click on this icon to be able to
select the node from the main model. Once the cursor changes the shape, simply select a
node from the model. The Node and Point boxes will automatically fill up with the correct
information. Otherwise, type an existing Node number or location Point coordinates to define
the axis of rotation.
Use this as Reference Point for Beta angle generation. In previous versions of STAAD.Pro, one
limitations of the Circular Repeat feature was that the member orientation was not taken
into consideration during the circular generation. This limitation has been addressed now.
If the Use this as Reference Point for Beta angle generation switch is turned on, the point
through which the axis for circular repeat operation passes will be used as the member
reference point for all the generated members. This point along with the local X axis of the
generated member will define the local X-Y plane of the member and hence the member
orientation gets automatically set.
Total Angle:
Provide the total sweep angle of rotation between the original structure and the last copied
structure.
No of Steps:
Provide the number of steps we want over the specified Total Angle.
Link Steps and open Base:
If you want to automatically connect the steps by new members, check the Link Steps check
box. To avoid joining the base of the copied structure, check the Open Base box.
The Circular Repeat. Rotate and Mirror dialog boxes have been enhanced to remain open so
that the selection beams, nodes, etc. can be accomplished even while the box is open. Also,
selection of critical points such as the node, point or plane where the axis of rotation crosses
can now be selected graphically while the box remains open. This eliminates the
inconvenience in the past where if this location was known before selecting one of the
geometry options, the box had to be closed down to determine the location first.
1. Select the objects to be copied.
5. Insert Node
This facility allows the user to insert node on an existing member. The member is split into
the corresponding number of segments with automatic generation of node and member
numbers, member properties and loads.
If you choose this option, the Insert Node cursor appears. By using that cursor, you can
select the member to split. The Insert Node dialog appears, as shown below:
Beam Length:
This lists the distance from node A to node B along the beam to be split.
New Insertion Point:
Provide the Distance from the start node of the member in current length units.
Alternatively, provide Proportion of the total length of the member to position the new node.
Click Add New Point to add the node.
Add New Point:
After providing the Distance or the Proportion, click on the Add New Point to add the node.
Add n points:
To split a beam by inserting n number of points, use this option. The beams are split up into
n+1 segments.
6.Add Beam
This option in geometry menu allows you to add members by connecting existing nodes.
Choosing this option brings up the following sub-menu.
Click on Yes to create a new node. The Insert Nodes dialog box will prompt for the exact
location where the nodes is to be created. once the desired node or nodes have been input
that box, click on the OK button to generate the new nodes on the selected beam. If the new
node input is not within a close proximity of the point clicked on the screen, no
draggableline will be shown. Click on the new node to start the creation of the beam.
Then, drag the mouse to another existing node location or repeat the same steps again to
dynamically create another new node.
Chapter- 3:
1. Run Structure Wizard
2. Generation Structure Models
3. Merging the Generated Model in STAAD.Pro
4. Importing CAD Models
The Protype Models and Saved User Models options on the top of the left side of the screen.
If the Prototype Models option is selected, the Model Type will list the types of prototype
structure available as shown below. If the Saved User Models option is selected, the Model
Type will display the list previously done and saved models by the user.
To insert any customized item under any Model type, select that Model Type and click the
mouse at the bottom of the same pane. Right-click the mouse and from the context menu,
select Add Plug-in and you can load the corresponding .dll file. We can also delete a
particular structural item by selecting that particular item and by clicking the Delete Model
Plug-in from the context menu. A structural item under any Model Type may be renamed by
using Rename Model Generator from the context menu.
The customized list of the Prototype can be saved in different files. By default,
STAAD.Pro/Structure Wizard uses the default .STP file. We can save any changes in this file.
Also changes can be saved in any file other than default .STP. To save the changes, select
Save As. from the File menu in the Structure Wizard window. Provide the path and name of
the .STP file and press OK.
To open any .STP file to use the customized Structure Libraries, select the File| Open menu
option from Structure Wizard main menu. Specify the path and name of the .STP file and
press OK.
Use the View, Zoom, Pan and Rotate icons to change the orientation of the model.
Selection of Unit:
The unit of the length should be specified before the generation of a model. From the File
menu, click Select Unit and the Select Unit dialog box will appear as shown below. We can
select any unit of length from Imperial or SI/Metric system of units.
Model Type: Truss
Select the Howe Roof structure type under model type Trusses. Drag the item into the right
side window and release the button. The Select Parameters dialog box will appears to
specify the Truss parameter as shown below:
After defining the parameters click Apply and the prototype truss will appears with the X, Y
and Z axes on the screen.
Right click in the right side window containing the generated model. The context-menu will
display the options Change Property, Scale and Delete. We can edit the value of the
parameters by clicking the Change Property, which will pop-up the select Parameters dialog
box. Enter the length, height and width of the truss and the number of bays along those
directions. To modify the spacing of individual bays, click the browse button and in the dialog
box that appears, type new spacing and click OK. Click the Apply button to parametrically
generated the truss model. Click Close to finish.
We can re-scale the model in X, Y and Z directions separately using Scale from the context
menu. You can also delete the particular model by clicking Delete from the context menu.
The structure Wizard window will now close. In the STAAD.Pro window, the Paste Prototype
Model dialog box will appears., in which we can type the shift of the origin of the Structure
Wizard model from the origin of the STAAD.Pro axis system or we can type coordinate of the
node of the STAAD.Pro structure with which we can want to connect the Structure Wizard
model or click on the Reference Pt button to connect the node of the existing structure in
STAAD.Pro with the Structure Wizard model by clicking on the joints where they will be
connected. Click OK to finish.
In the Frame Models Continuous Beam, Bay Frame, Grid Frame and Floor Grid have similar
parameters in the Select Parameter dialog box. Type values for Length, Height & Width and
number of bays for each. To modify the spacing of the bays, click the browse button and in
the dialog box that appears, type new spacing and click OK. Click the Apply button to the
parametrically generated model.
The Cylindrical Frame, Reverse Cylindrical Frame and Circular Beam have similar Parameter
in the Select Parameter dialog box. Type values for Length, Radius, Angle and number of
bays along length and periphery. To modify the spacing of bars, click the browse button and
in dialog box that appears, type new spacing and click OK, Click the Apply button to
parametrically generate the model.
Scan DXF:
If the geometry of the model is created using the drawing program like AutoCAD and saved
in a DXF file format, it can be imported using this option. After dragging the Scan DXF icon
into the right side window, a Open dialog box appears and noe=w locate the DXF file,
which we want to open, select that file and press OK. This feature supports the limited
number of CAD entities like Line, 3D-Polyline and 3D-Face.
STAAD Models:
This allows the geometry of the previously created model to be imported and altered. After
dragging the STAAD Models icon into the right side window, an Open dialog box will appear.
Now locate the STD file which you want to open, select that STD file and press OK. The
geometry from that STD file will be imported. That model can be scaled up or down along
the global X, Y and Z directions by clicking the right mouse button, choosing the Scale option
and provide the desired values.
Chapter- 4:
1. Support Specification
2. Support Page
3. Member Property
4. Member Offset
1.Support Specification
This allows the user to define the support conditions of the structure by providing fixed,
pinned, roller, inclined, spring supports, etc. Supports can defined and assigned from the
General| Support page also. This menu option is used to specify the supports on the
structures. The Support Specification menu offers several sub-menu options, as follow.
Click Commands Support Specifications.
Pinned:
This allows user to create the pinned support tag and assigned it to the selected nodes. A
pinned support is restrained in all three translational degree of freedom and free in the 3
rotational degrees of freedom.
Fixed:
This allows the user to create a fixed support tag and assign that to the selected nodes. A
fixed support is restrained in all 6 degree of freedom.
Enforced But:
Enforced But support type is the same as the Enforced support except that we have the
choice on the degrees of freedom we wish to restrain. For example, we can select Enforced
But and restrain just the FX, FY and FZ degree of freedom and let the remaining 3 free to
deformation.
Inclined:
This allows the user to create supports that restraints in an axis system that is inclined with
respect to the global axis system. There are two aspects defining the inclined supports:
Foundation:
To define a spring support for an isolated footing, click the Footing radio button. Provide the
dimension of the footing in current units settings and choose the Direction of the spring
action. Provide the soil Sub-grade value in the edit box. Click the Add button to add the
foundation support tag to the structure or click Assign to assign this support to selected
nodes.
Elastic Mat: In this method, the area is calculated using a Delaunay triangle principle.
Hence the candidates for this options are nodes which define the mat. To achieve best
results, one needs to ensure that the contour formed by the nodes form a convex hull.
Plate Mat: If the foundation slab is modeled using plate elements, the spring supports can
be generated using an influence area calculated using the principles used in determining the
tributary area of nodes from the finite element modelling standpoint. Hence the candidates
for this option are the plates which define the mat. When the mat is modeled using plates.
this produces superior results than the ELASTIC MAT type.
2.Support Page
When the General | Support Page is opened, a Supported Nodes tables and a Supports
dialog box appears in the data area. We may specify supports in two ways. We must first
create Support Specification and then select the nodes to which this support is to be
attached to. Alternatively, we may first select the nodes and then specify a support to be
assigned to the selected nodes. In second case, a new Support Specification is created along
with a support reference number. Also note that the Assign button become active if we have
already selected the nodes to which the support is to be applied.
Supported Nodes Table list all nodes for which supports have been defined. The type of
support is also displayed. The Supports dialog box allows us to define supports and assign
them to nodes. All supports that have been defined for the model are listed in the Supports
dialog box.
Create:
The Create button is for creating the supports to be applied on the structure. When you click
this button Create Support dialog box appears.
Edit:
For certain types of supports, the parameters of the support can be modified after the
support is created. The Edit button is available for that purpose. To do this, first select that
support type from the list. Click on Edit and dialog box corresponding to that support will be
re-displayed, allowing for changes to be made.
Delete:
Use this button to delete a previously assigned support.
Assignment Method:
The options under the Assignment Method offer different choices for assigning supports to
the structure.
Assign To Selected Nodes:
To assign a support to selected nodes, first select the support from the supports dialog box.
The support selected is highlighted. Then select the nodes to which this support is to be
assigned. When all the desired nodes are selected, click the Assign To Selected Nodes radio
button, then click the Assign button.
Assign To View:
To assign a support to all free nodes in a view, first select the support from the Supports
dialog box. The selected supported is highlighted. Select the Assign To View radio button,
then click the Assign button. All free nodes in the structure are assigned this support after
getting the confirmation.
Use Cursor To Assign:
To assign a support to nodes using the cursor, first select the support from the Supports
dialog box. The selected support is highlighted. Select the Use Cursor To Assign radio button,
then click the Assign button. The button will appear depressed and label will change to
Assigning. Make sure that the Nodes Cursor is selected so that we can select the nodes.
Using the cursor, click on the nodes to which this support is to be assigned. Click on the
Assign button again to finish.
Assign To Edit List:
To assign a support using a typed list of node numbers, first select the support from the
Supports dialog box. The selected support is highlighted. Select the Assign To Edit List radio
button, then type the list of node numbers and click the Assign button.
3.Member Property
This allows the user to provide the cross sectional properties of members with or without the
material specification. The same options can be gained access from the General | Property
page. The Member Property menu option is used to create the property tag and then assign
the specified property tag to select members through the Property Page. Alternatively, we
may first select members and then define the member property to be assigned to these
members.
The Member Property menu offers several sub-menu options as shown below:
Prismatic:
This allows the user to assign Circular, Rectangular, Tee, Trapezoidal, General, etc. Cross
sections to the frame members.
When we select the Prismatic option, the Property dialog box appears as shown below. Also
note that the Properties dialog box also opens simultaneously letting us utilize some of the
other operations available from that dialog box.
Material: Check this box and select the material from the drop down list if the new member
property tag should include the materials constants.
Circle: To define a circular section, click on the Circle tab as shown in the previous figure.
Enter the section diameter YD and select the material.
Rectangle: To define the rectangle section, Click on the Rectangle tab. Enter the height YD
and width ZD of the section and select the material.
Tee: To define a tee section, click on the tee tab. Enter the height YD, width ZD stem height
YB and stem width ZB and select the material.
Trapezoidal: To define a trapezoidal section, click on the Trapezoidal tab. Enter the height YD,
top width ZD, bottom width ZB and select the material.
Tapered Tube: This allows the user to specify a I-section having a varying depth over the
length of the member by using 7 parameters as shown below:
4.Member Offset
The beams and columns of structure are characterized by lines in the computer model. In
the actual structure, a beam spans distance which in the clear span between the faces of
columns. But in the computer model, the line for the beam spans among the centerlines of
the column. The half depth portion of either column is significantly stiffer than the beam
itself from the stand point of bending. To take benefit of this extra stiffness, we may affirm
that the start and end faces of the beam are offset from the node by a distance identical to
the half-column-depths.
Member offsets can be specified in other situations too. Examples are
When a bracing member does not meet the node which is defined in its incidence list.
A girder and top slab in the bridge where the centerline of the girder is several inches
below the centerline of the slab.
This facility becomes very useful when the user wants to have the structural parameters of a
member viz. shear force, bending moment by considering the clear distance of the member
between the supports. This facility can accessed from the General | Specification also. When
you select the offset menu option in the command menu, the Member Specification dialog
box appears as shown below.
Location:
Location defines the offset end of the member. Start is the starting point of the member and
End is the Ending point of the member. Start and End depends on the Member Incidence of
the member. Selecting one of these options defines the member offset to be at the start
point or at the end point of the member.
Direction:
Choose the Local for assigning the offsets in the local axis system. Otherwise, choose the
global axis system.
Offsets:
Type the offset distance from the joint in the three global directions. Click the Add button to
add this specification to the structure or click Assign to assign the specification to selected
member as well as add this specification to the structure.
Chapter- 5:
1. Loading 1
2. Loading 2
3. Wind Load Generation
4. Assigning Wind Loads
Loading 1
In STAAD.Pro V8i, loads in a structure can be detailed as Dead load, Live load, Wind load,
Snow load, Seismic load, temperature load and fixed-end member load. STAAD.Pro V8i can
also calculate the self-weight of the structure and make it as uniformly distributed loads
(UDL) in analysis. Self-weight of the members can be applied in any desired direction.
Click Commands Loading Primary Loading.
Now the Create New Definitions / Load Cases / Load Items dialog box appears. Now you have
to define the loads, then click Add button.
Factor- Specify the factor with which the calculated self-weight are to be multiplied.
A negative value indicates that the load is applies along the negative direction of the
selected axis.
Nodal Load:
Nodal loads is the combination of forces and moments, it may be applied to any free node of
a structure. These loads act in the global coordinate system of the structure. Two options are
available under Nodal Load: Node and Support Displacement. Positive value forces acts in
the positive coordinate directions of the axis.
Member Load:
The Member Load tab allows the user to apply loads on the span of frame members.
Concentrated Load:
To specify a concentrated force or moment, click the Concentrated Force or Concentrated
Moment tab. The data items are explained below.
Loading 2
Area Load: This allows the user to apply load over area, which will be distributed on
surrounding beams based on the one way distribution. This load is a one-way distributed
pressure load on members that circumstances a panel. Enter the value of area load in
current units. This load always acts along the positive local y direction on the two longest
member on each panel.
Note: Area load should not specified on members declared as Member Cable, Member Truss
or Member Tension.
Floor Load: User can apply the load over the panel, which will be distributed on
surrounding beams based on a two-way distribution. This load is two-way distributed
pressure load on members that circumscribe a panel. The data items are explained below:
Load Floor load value in the current units. This load will act parallel to the global vertical
axis.
Direction The floor may be considered as acting perpendicular to plane of the panel on
which it is defined. This is normal load static condition.
Range Define X Range/ Y Range/ Z Range. Specify the location of the floor using the
Define X Range option. The load will be calculated for all members lying between this range.
One Way Distribution Check the box for one way distribution to get a one way type
distribution of the pressure. In such cases, the program find out the shorter side of the
panel. It then divides the load in between the long direction beams. No load is generated by
this option if the panel is square in shape.
Plate Load: The Plate Load tab allows the user to apply elements loads. The Plate Load tab
offers several sub-menu options as shown below.
Load W1 is the variable using which the pressure value is defined, in pressure units.
Direction The load may be applied along the local Z axis, or along one of the global X, Y
or Z axis (GX, GY, GZ)
Concentrated Load:
Use this option to define a concentrated load that acts on specific point within the boundary
of the element. If a load acts at a node point of an element, it is advisable to apply it using
the Nodal Load option described in earlier pages.
Load The magnitude of load is specified in the box alongside Force. X and Y define the
location of the load, in terms of the distance from the origin of local X and Y axes of the
element.
Direction The load may be applied along the local Z-axis, or along one of the global X, Y
or Z axis (GX, GY, GZ).
Partial Plate Pressure:
To Specify a uniform pressure on the entire element or a non user specified portion of the
element, use this facility. The data items are explained below:
Load The element pressure (force per unit area) or Concentrated load (force unit). For
concentrated load the values of X2 and Y2 must be omitted, while X1 and Y1 must be
specified.
X1, Y1, X2, Y2 For element pressure (force per unit area), these values represent the
coordinates of the rectangular bpundary on which the pressure is applied. If X1, Y1, X2 and
Y2 are all zero; the pressure is applied over the entire element. If X1 and Y1 are specified but
X2 and Y2 are omitted, then W1 is treated as concentrated load.
Direction GX, GY, GZ represent the global X, Y and Z direction along which the pressure
may be applied Local Z indicates that the pressure is applied normal to the element in the
local Z direction.
Trapezoidal: To specify a trapezoidal varying pressure load on a plate, select the
Trapezoidal tab. The load is applied over the entire element in the local Z direction, varying
along the positive local X or Y direction. The data items are explained below.
Direction of Pressure GX, GY and GZ represent the global X, Y and Z direction along
which the pressure may be applied. Local Z indicates that the pressure is applied normal to
the element in the local Z direction. Enter the pressure intensity F1 at the lowest local
coordinate location (start) and the intensity F2 at the highest local coordinate location (end),
Start and End are defined basd on the positive direction of the local X-axis or local Y-axis.
Variation along element Define the direction in which the pressure varies as either the
local X ot Y direction or Choose the joint option, which is discussed next.
Joint Check the joint option to apply different value of pressure at different nodes of the
plate element. When checked, the dialog box will change as shown below. Apply different
values of pressure in the edit boxes for the different nodes.
Hydrostatic: To model loads due to hydrostatic pressure on one or more adjacent elements,
select the Hydrostatic tab. The hydorstatic load is converted to Trapezoidal loads on the
elements. The load is applied over the entire area of the element. The data items are
explained below:
Force Enter the value of the load at the minimum and maximum global axis in current
units. For example, to model a retaining wall with soil pressure, W1 is the force at the
bottom of the wall and W2 is the force at the top of the wall.
Interpolate along Global Axis Specify the global axis (X, Y or Z) along which the load
vary from W1 to W2. For example, the load would vary along the Y axis on a vertical
retaining wall.
Select Plate(s) Unlike the load definition options, we must select plate(s) for this option
to became active. Click on this button to select plate(s). Click on the Select Plates button. A
dialog box will appear. Select all the plates of a wall on which we wish to apply hydrostatic
load. Click on Done. The hydrostatic dialog box will re-appear.
Direction of pressure Specify the direction of design pressure as Local Z axis or global
axes (GX, GY or GZ) and click on Add. This will assign a linearly varying hydrostatic load on
all the selected elements.
Element Joint Load: To specify a varying pressure at each joint on a plate, select the
Element Joint Load option. The data items are explained below.
Joint Load Data Choose Three Noded Facet / Four Noded Facet depending on whether
the plate element is 3 noded 4 noded.
Direction The load may be applied along the local Z axis or along one of the global X, Y
or Z axis (GX, GY, GZ)
Add After defining a load, click the Add button to add this under current load case in the
Loads dialog box.
Open structures are those like transmission towers, in which the region between members is
Open allowing the wind to blow through it. The procedure for load generation for open
structures is
1. Calculate the exposed area of the individual members of the model.
2. Multiply that exposed area by the wind pressure to arrive at the force and apply the
force on the individual members as a uniformly distributed load. It is assumed that all
members of the structures within the specified Rangers are subjected to the pressure
and hence, they will all receive the load. The concept of members on the Windward
side shielding the members in the inside regions of their structures does not exist for
open structures.
At a large structure may consist of hundreds of panel and members, the user with the help
of this facility can avoid a considerable amount of work in calculating the loads.
The wind load menu option allows the user to define the parameters for automatic
generation of wind loads on the structure.
STAAD.Pro V8i is now capable of generating the wind pressure profile for a structure in
accordance with the ASCE-7-95 as well as the ASCE-7-02 codes. The pressure profile is the
table of values of wind intensity versus height above ground.
The calculated pressure may then be applied on the structure to compute loads on the
member using the in-built programs wind load generation algorithm for the closed as well
as open-lattice type structures.
When the wind load B&B of my menu option is selected, the new wind type dialog box
appears, as shown below.
Enter the Type No. which denotes the number by which the wind load type will be
identified. Multiple wind types can be created in the same model. Click on the Add button
within this dialogue box and then click on close.
The newly created TYPE 1 wind definition will appear underneath wind in the Load dialogue.
Select the TYPE 1 name in the tree control and click on the Add button. The dialogue box
shown below will prompt for the pressure profile for this wind definition.
As we said earlier, the pressure profile is the table of wind intensity versus height above
ground. If we know that, that information can be typed into the box above.
To calculate the wind intensity, use the following formula from IS 875-Part 3.
Vz = Vb k1 k2 k3 and pz = 0.6 Vz2
where, Vz = Design wind speed at any height
Vb = Base wind speed.
k1 = probability factor.
k = terrain, height and structure size factor.
Select type:
Choose a previously defined wind load type from the drop down list.
Direction:
Specify the global direction in which the wind load is to be generated by clicking the X, Z, -X
or Z radio button. When wind is generated in X direction, the wind load is applied on the
near side and when X is chosen the load is applied on the far side. Generation in Z or Z
also works the same way.
Factor:
Specify the factor to multiply the calculated wind loads.
Open structure:
By default, the load generation is based on the assumption that the region between
members is covered by panels. To generate loads on open structures like highway signs or
transmission towers, switch on this box. The members are selected and X is used and the
factor is positive, then the exposed surface facing in the X direction will be loaded in the
positive X direction. If X and a negative factor, then the exposed surface facing in the X
direction will be loaded in the negative x direction. If X is entered and a positive factor, then
the exposed surfaces facing in the +X direction will be loaded the positive X direction.
Chapter- 5:
1. Analysis
2. Concrete Design
3. Time History Analysis
Analysis
STAAD.Pro V8i offers STAAD engine for general purposes structural analysis and design. The
modelling mode of STAAD environment is used to prepare structural input data. After the
analysis is performed, used the menu option File View Output File STAAD Output
to view the output files.
The STAAD Analysis engine perform analysis and design simultaneously. However, to carry
out the design, the design parameters too must be specified along with the geometry,
properties, etc. Before you perform the analysis. Also, note that you can change the design
code to be followed for design and the code check before performing the analysis/design.
Perform analysis:
To do the analysis must be need to add the command from Commands Analysis
Perform analysis
This allowed the user to specify the instructions for the type of analysis to be performed
using STAAD engine. In addition, this command may be used to print various analysisrelated data such as load information, statics check information, mode shapes etc.
The analysis menu offers several sub menu options. When you select one of the analysis
commands, you may specify the analysis-related data to be printed in the STAAD output
(.ANL) file by selecting the print option radio buttons, explained below:
Load data: print all the load data.
Statics check: provides summation of the applied load and support reaction as well as
summation of moment of load and reactions taken around the origin.
Statics load: print everything that statics check does and summation of all internal and
external forces at each joint.
Mode shapes: print mode shapes values at the joints or are calculated mode shapes.
Both: this option is equivalent to the load data plus statics check option.
All: this option is equivalent to load data plus statics data.
Run Analysis:
The Analysis is performed under the commands under the analyse menu in the Modelling
Mode. Select the Run Analysis option to perform Analysis/Design.
This dialog box displays the status of the analysis process. If an error occurs during the
analysis, the above dialog box displays the error message.
View Output File: it will invoke the STAAD viewer with the analysis results presented in a
textual format.
Go to Post Processing Mode: it will take you to the STAAD.Pro Post processor where you
can graphically.
Concrete Design
STAAD has the capabilities of performing concrete design on limit state method of IS 456
(2000).
Beam Design:
Beams are designed for flexure, shear and torsion. If required the effect the axial force may
be considered. For all these forces, all active beam loadings are pre-scanned to identify the
critical load cases at different section of the beams.
Column Design:
Columns are designed for axial forces and biaxial moments at the ends. All active load cases
are tested to calculate reinforcement. The loading which yield maximum reinforcement is
called the critical load. Column design is done for square, rectangular and circular sections.
By default, square and rectangular column and designed with reinforcement distributed on
each side equally for the sections under uni-axial moment.
Design Parameters:
The program contains several parameters which are needed to perform design as per IS 456
(2000). Default parameter values have been selected that they are frequently used numbers
for conventional design parameters. These values may be changes to suit the particular
design performed.
Performing Concrete Design:
1. Click Commands Design Concrete Design.
2. Now the user can specify the design parameters for the structure.
3. Concrete Design dialog box appears.
4. Click the Select Parameters button. Now you can select the desired parameters for the
concrete design.
5. Click Ok. Then Click Define Parameters button, now you can define the parameter
Default Value
25000 KN/mm2
415000 KN/mm2
415000 KN/mm2
60 mm
12 mm
10mm
8 mm
Description
Concrete yield strength.
Yield stress for main reinforcing steel.
Yield stress for secondary reinforcing steel.
Maximum main reinforcement bar size.
Maximum secondary reinforcement bar size.
Minimum main reinforcement bar size.
Minimum secondary reinforcement bar size.
7. Click Add button to add the parameters, then assign the commands to the respective
members.
10. Then Run Analysis, the result provide the suitable concrete design for the structure.
NOTE: After the analysis, double click the member of the structure, it show the concrete
design, if the concrete design of the element is missing, then it is said to unsafe.
Select the Acceleration, Force or Moment option to define the type of functions being input.
Save:
Select this option to create an external file containing the history of displacements of every
node of the structure at every time step.
Function Options:
Define Time VS <loading type>
Used to specify a time history forcing function, where the loading type is that selected
above. Specify the values Time and corresponding Force or Acceleration. The time history
function is plotted on the bottom of the dialog as data pairs are entered.
Harmonic:
Curve Shape:
Specify if the harmonic function is a SINE or COSINE curve.
Frequency or RPM:
Choose Frequency and enter circular frequency in cycles per second or RPM and enter
revolutions per minute.
Amplitude:
Max. Amplitude forcing function in current units.
Phase:
Phase angle in degrees.
Cycles:
No.of cycles of loading.
Step of Sub Div:
Choose the step option to time step of loading SubDiv to sub divide a 1/4 cycle into this
many integer time steps.
Spectrum:
Select this Function Option to provide spectrum parameters for your time history loading.
Time History Parameters Dialog:
Time Step:
Specify a solution time step to be used in the step-by-step integration of the uncoupled
equations.
Damping:
The following options are available for specifying damping:
Damping-this is to be used for specifying a single model damping ratio which will be applied
to all mode. The default value is 0.05.
CDAMP if a damping ratio has already been specified under CONSTANTS based on the
type of material in the structure, the value may be used directly in time history analysis.
Check this option for that purpose.
MDAMP we wish to utilise individual damping ratios for individual modes, that is achieved
through the means of the MDAMP option. The first step to doing this is the specification of
those individual damping ratios, as explained under section 5.26 .3 of the STAAD technical
reference manual and is done graphically from the command-define damping menu. If this
first step has been completed, the instruction to utilise MDAMP done by selecting this option
shown above.
Arrival time:
specify values of possible arrival times of the various dynamic load types. The arrival time is
the time at which the load type begins to act at a joint or at the base of the structure. The
same load may have different arrival times for different joint and hence all these values
must be specified here. The arrival time and time force pairs for the load types are used to create the
load vector needed for each time step of the analysis.
Chapter- 6:
1. Introduction to FEM
2. Plate
3. Surface
4. Meshing
Introduction to FEM
The Finite Element Method (FEM) is a numerical technique for finding approximate solution
of partial differentially equation (PDE) as well as integral equation.
The finite element method is a good choice for solving partial differential equations more
complicated the domains, when the domains changes, when the desired precision varies
over the entire domains, or when the solution lacks smoothness.
The final element method originated from the need for solving complex elasticity and
structural analysis in civil and aeronautical engineering. Its development can be traced back
to the work by Alexander Hrennikoff and Richard Courant. While the approaches used by the
pioneers are dramatically different, they share one essential characteristic: mesh
discretization of continuous domains into a set of the sub-domains, usually called elements.
The development of final element that began in the earnest in the middle to late 1950s for
airframe and structural analysis and gathered momentum at the University of stuttgart
through the work of Jhon Argyris and at Berkeley through the work of Ray W. Clough in the
1960s for use in civil engineering. By late 1950s, the key concept of stiffness matrix and
element software NASTRAN in 1965. The method was provided with rigourous mathematical
foundation in 1970 with the publication of strang and FixsAn analysis of the finite element
method has since been generalised into a branch applied mathematics for numerical
modelling of physical system in a wide variety of engineering disciplines.
Plate
Add Plate:
This option allows you to Triangular or Quadrilateral plate elements by connecting existing
nodes. To add quadrilateral plate, select Quad from the sub-menu. For triangular plates,
select Triangle from the sub-menu . The cursor changes to Quad plate or Triangular Plate
shapes. To create new elements, simply click on the existing nodes in the right sequence. A
rubber banded area shows the boundary of the plate being generated.
Set New Plate Attribute:
Similar to the Set New Member Attribute command in which the user is in can define the
property, material and releases to each new plate element as it is created, has been
introduced.
In order to define the attributes for plate element before they are created, go
to Geometry Add Plate Set New Plate Attributes from the main menu.
A dialogue box will prompt for various attributes of the plate to be pre-defined. A summary
of a specific attributes are defined in the table below.
Button
Create New Property
Function
Prompts the plate thickness
dialogue box that the thickness
of the plate at each of the
common node can be defined.
Defined the various material
properties of the plate
including poison ratio, modulus
of elasticity, shear modulus,
etc.
Multiple properties, releases and materials can be created and saved for future use. To
choose from various pre-defined types, simply select the appropriate definition using the
Select Property, Select Material or the Plate Release drop-down boxes.
For the program to recognize the pre-defined attributes, the Assign these attributes while
creating a new plates check box must be checked. Any new plate element created from
here on will now possess these attributes.
How to Sketch Plates:
1. Click the plate icon
2. Now automatically beam cursor will change into plate cursor and nodes in the structure
are visible.
5. Click Thickness button, now the Plate Element/ Surface Property dialog box appears,
where you add different types of member properties of plate and surface element.
6. Type respective value of thickness for the plate element. Click Add button.
7. Now click Select menu Plate cursor.
8. Now select the plates and select the radio button Assign to selected plates and click
Assign button.
9. Now open the 3D rendering page. You can see the Plate with defined thickness.
Surface
Add Surface:
Adding surface is similar to the adding plates where the plates can be placed by clicking only
4 node points while the surface can be placed by clicking more than 4 node points. Finally
you have to click the node point where you start placing the surface.
How to Add surface in the structure:
1. Click Add Surface icon or Click Geometry menu Add Surface.
2. Now the beam cursor changes into surface cursor.
3. Place the surface by clicking the node points and finally click the node point where begin.
4. As usual define the property for surface. Type the respective thickness value for surface
member.
5. Now Assign the member property to the surface by selecting the surfaces using the
surface cursor.
Meshing
Meshing is the process of creating a finite element mesh over the respective member. The
nodes that form the corners of the polygon representing the super element must already
exit on the drawing before the facility can be availed. They can be selected in a sequence
and the process launched.
Meshing can be done over the plate and surface they can be classified into two are
1. Plate mesh.
2.
Surface mesh.
Plate Meshing:
This is an utility meant for taking an existing plate element and subdividing into a set of
smaller elements. Consequently, a plate element must already exist on the drawing in order
for this facility to be enabled. Using the Plate Cursor, Click the right mouse button on the
element and select Generate Mesh. Alternatively select the Geometry menu Generate
Plate Mesh.
If the element being meshed is triangular, the polygonal mesh feature described in the
previous section will automatically become activated. If the element is quadrilateral, the
user have to choose between polygonal and quadrilateral meshing.
1. Select the plate element, right click in the selected element.
2. Click Generate Plate Meshing. Now the Meshing type dialog box appears.
3. Choose the type of meshing, Click Polygonal Meshing and click OK
4. Now the Define Mesh Region dialog box appears, user have to define the boundary of the
meshing surface. Click OK button.
5. Now the meshing surface is visible, then apply the plate load and proceed analysis.
Polygonal Meshing.
Quadrilateral Meshing.
Surface Meshing:
Surface meshing is similar to the process of plate meshing. Same procedure is followed for
the surface meshing. Click Geometry menu Generate Plate Mesh. Now select the
surface element and provide respective boundary condition. Click OK button. Now you get
the surface mesh.
Chapter- 7: (Slabs)
1. Desgin Of Slab
2. Design Of One Way Slab
3. Design Of Two Way Slab
4. DesignOf Staircase
5. Design of Bridge using STAAD.Beava
Slab Design
Slabs are the important structural component where the pre-stressing is applied. With
increase in the demand for fast track, economical and efficient construction, pre-stressed
slabs are becoming popular. The slabs are presented in two groups are
A slab is pre-stressed for the following benefits. 1. Increased span-to-depth ratio Typical
values of span-to-depth ratios in slabs are given below.
2. Reduction in self weight. 3. Section remains uncracked under service loads which
increases durability. 4. Quick release of formwork which help for fast construction. 5.
Reduction in fabrication of reinforcement. 6. More flexibility in accommodating late design
changes.
Design of One Way Slab
One Way Slab:
Rectangular slabs can be divided into two groups based on the support condition and lengthto-breadth ratios. The one-way are identified as follows:
1. When a rectangular slab is supported on all the four edges and length-to-breadth
(L/B) ratio equal to or greater than two, the slab is considered to be a one-way-slab.
The slab spans predominantly in the direction parallel to the shorter edge.
2. when a rectangular slab is supported only on two opposite edges, it is a one-way slab
spanning in the direction perpendicular to the edges. Precast planks fall in this group.
A slab in a framed building can be a one-way slab depending upon its length-to-breadth
ratio. A one-way is designed for spanning direction only. For the transverse direction, a
minimum amount of reinforcement is provided. A slab under flexural behavior like a beam.
One-way slabs are analysed and designed for spanning direction similar to the rectangular
beams. A slab of uniform thickness subjected to a bending moment uniformly distributed
over its width. Although a one meter wide strip of the slab is considered as a beam for the
analysis and design for flexural strength, there is a difference between the beam and slab as
follows.
When a beam bends, the portion of the section above the neutral axis is under compression
and hence subjected to a lateral condition. Hence after bending, the cross-section, will
strictly not be a rectangular, but nearly a trapezoidal.
In the case of a one-way slab, for a design strip, such lateral displacements and strains are
prevented by the remainder of the slab on either side i.e it retains the rectangular shape
after even after bending. The final design involves the checking of the stresses in concrete
at transfer and under service loads with respect to the allowable stresses. The allowable
stresses depend on the type of slab. During the design, the reinforced bars are usually
spaced uniformly over the width of the slab.
Design Steps In STAAD.Pro V8i:
1. Create a member to represent the slab.
2. Assign the suitable support to both ends.
3. Assign the Cross section properties.
4. Assign the load as follows
Dead Load.
1. Selfweight
2. Uniformly Distributed Load to represent the floor finish
Live Load
Tread: The horizontal top portion of a step where foot rests is called as tread. The
dimension varies from 270 mm for residential buildings and factories to 300 mm for
public buildings where large number of persons use the staircase.
Riser: The vertical distance between two successive steps is called as riser. The
dimension of the riser varies from 150 mm for public buildings to 190 mm for
residential buildings and factories.
Waist: The thickness of the waist-slab on which steps are made is called as waist. The
thickness of the waist is the minimum thickness perpendicular to the soffit of the
staircase. The steps of the staircase resting on waist-slab can be made of bricks or
concrete.
Riser = 160mm
Tread = 270mm
STAAD.Beava
The general philosophy governing the design of bridges is that, subject to set of loading
rules and constraints, the worst effects due to load application should be established and
designed. The process of load application can be complex as governing rules can impose
inter-dependent parameter such as loaded length on a lane, lane factors and load intensity.
To obtain the maximum design effects, engineers have to try many loading situations on a
trial and error basis.
This leads to the generation of many live load application instances and a large volume of
output data that has to be combined with dead load effects as well. In view of the above, a
computer program has been developed to minimize the load application process while
complying with national code requirements.
Users can avoid trial and error approach and eliminate any possible errors arising from
inaccuracies associated with it. This program is based on the use of influence surface for a
given effect on a bridge deck relates its value to movement of a unit load over the area of
interest. The influence surface is a three dimensional form of an influence line for a single
member.
STAAD.Pro V8i will automatically generates influence surfaces for effects such as bending
moments for elements, deflection in all degree of freedom of nodes and support reaction.
The engineer will then instruct the program to utilise the relevant influence surfaces and
with due regards to code requirements, optimise load positions to obtain the maximum
desired effects.
Once the influence surfaces have been generated, they are saved and can be used for any
further investigation that may be requires. This will remain valid as long as the user has not
altered the structural model. Changes to the structural model can alter the pattern of the
influence surfaces and the user must ensure that a further run takes place before any
further processing.
The Engineers knowledge and judgement is critical in deciding which effects are required
and at which position to obtain them. This is where users can save lot of processing time and
can ensure critical positions are not missed. The current versions of Bridge Engineering
Automated Vehicle Application (B.E.A.V.A) supports the UK BS5400 part2, American AASHTO
and Indian IRC 6:2000 standards.
All the relevant code instructions for loading definitions and traffic lane calculations are
incoporated in BEAVA and in case where vehicle axle arrangements are not standard, it is
possible to define a vehicle and save it in library for use it in analysis. BEAVA is fully
integrated in STAAD.Pro and utilises the GUI for all input data.
The user defines the width of the carriageway as straight or curved parallel lines, BEAVA
then automatically calculates the following in accordance with selected code:
Loading arrangements for the effects requested can be displayed on the model and for
every loading arrangements are produced, the user can instruct the program to generate a
STAAD.Pro load case. The added live load cases can be combined with dead loads i in the
normal way of STAAD.Pro load combination generation. The final model can then analsed in
STAAD.Pro and then post-processed.
To avoid inefficient use of the program, it is recommended that the following steps be taken
in the order suggested.
Create the structural model including member properties and support conditions.
From the Mode menu select Bridge Deck Pre-processor; note that if your security
device is not programmed for this module you will not be able to proceed.
The menu bar has been modified to show Deck and Vehicle.
From Deck menu, select Influence Surface generator. This will start analysis
procedure to create the influence surfaces.
From Deck menu, select Define Carriageway and define either a straight or a curved
carriageway.
From Deck menu select Load Generator. Proceed to select the required input, on
completion, select OK. The loading program is now engaged and will calculate all the
requires loading arrangements that lead to max/min effects you have request. On
completion, a text file will be displayed on the screen containing the loading
arrangements, which you can now display graphically.
For each effect requested display the loading arrangements and examine the
correctness.
For each effect requested, select Create Loading in STAAD Model from Deck menu.
After all load cases have created, from Mode menu select Modelling and return to
carry on with other load generates and combinations.
3. Use the Geometry menu Generate Surface Meshing to create the bridge deck as follows.
4. Now type the values and click Apply. Model appears like as shown below.
Beam parallel the X and Z direction = Rectangular Cross Section with 0.5 m x 0.5 m
in concrete.
Member Offset = Decide the suitable member offsets as per the cross section
dimensions.
6. Add a primary load case with Dead Load type and assign the Selfweight for all the
elements.
7. Perform Analysis and Run Analysis. Note the node id, which has the maximum
displacement due to load.
8. Click Mode menu Bridge Deck Preprocessor.
11. Click the Loading menu Run Influence Generator. It takes sometimes to complete
the analysis over the plates elements.
11. Click the Loading menu Influence Diagram Check the diagram for all the
elements.
Orientation = 90
Length = 75
Origin = 2
Width = 4
14. Click Ok. Now you can get the model with the corresponding lanes.
15. Click Vehicle menu Vehicle Database. Now Vehicle Database dialog box appears.
16. Select the suitable IRC Vehicle for your design. Click Ok.
17. Click Loading menu Run Load Generator
Limit = Ultimate
18. Click Ok. Now automatically it will generate result values in notepad.
20. Right click in the window, select the Structures Diagrams Select the Results values
and click OK.
21. Click Loading Create Loading in STAAD Model. Now the following dialog box
appears
22. Now Run Analysis and then move to post processing. In Post Processing window, click the
Beam tab Forces.
3. Now
you can provide the concrete design over the model.
Chapter- 9: (Steel)
1. Design Of Steel Structures
2. Member Specification
Table Member Property
Identify the members and the load cases to be considered in the design.
Presently, STAAD.Pro V8i supports steel design of wide flange, S shape, M shape, HP shapes,
T shape, I shape, angle, double angle, channel, double channel, pipes, tubes, beams with
cover plate and composite beams.
Parameter Name
Default Value
FYLD
Description
250 MPA
Yield strength of steel.
KY
1.0
K value in local y-axis. Usually, this
is minor axis.
1.0
LY
Member Length
LZ
Member Length
KZ
MAIN
180
NSF
1.0
RATIO
1.0
TMAIN
400
TRACK
CMYCMZ
DFF
DJ1
DJ2
Member Specification
Cable:
This command may be used to model a specified set of members as CABLE members. The
CABLE members, in addition to elastic axial deformation, are also capable of accommodating
the stiffness of initial tension due to static loads. The Cable menu option under the
commands menu Member Specification allows the user to define cable members. When
you select the Cable menu option, the Member Specification dialog box appears, as shown
below:
Provide either the Initial TENSION in the cable as o force, or the Unstressed LENGTH of the
cable of the cable member. Click the Add button to add this specification to the structure or
click Assign to assign the specification to selected members as well as add this specification
to the structure. The TENSION specified in the CABLE member is applied on the structure as
an external load as well as is used to modify the stiffness of the member. The tension value
must be positive to be treated as cable; otherwise, it is a truss. If TENSION or the value is
omitted a minimum tension will be used.
This is truss member but not a tension only member unless you also include this member in
a MEMBER TENSION input. Note also that Member releases are not allowed. The tension is a
preload and will not be the final tension in the cable after the deformation due to this
preload.
Tension/Compression:
This command may be used to designate certain member as Tension only or compression
only members. The Tension Only / Compression Only menu option in the Member
Specifications menu allows the user to define tension only or compression only members.
These members are capable of carrying tensile forces only.
Click the Add button to add this specification to the structure or click Assign to assign the
specification to selected members as well as add this specification to the structure.
MEMBER TENSION 0
This command switches off ALL tension/compression only specification for load cases, which
are specified subsequent to this command, usually entered after a CHANGE command. There
is no list associated with this command. Hence, for any further primary load cases, the
tension/compression only attributed is disabled for ALL members.
Tension only member are truss/cable members that are capable of carrying tensile forces
only. Thus they are automatically inactivated for load cases that create compression in them.
Compression only members that are capable of carrying compressive forces only. Thus, they
are automatically inactivated for load cases that create tension in them. Member Releases
are not allowed on members with this attribute.
The Procedure for analysis of Tension only or Compression only members requires iteration
for every load cases and therefore may be moderately involved. The user may also consider
using the INACTIVE specification if the solution time becomes unacceptably high. If a
CHANGE command is used, then the SET NL command must be used to convey to STAAD
that multiple analyses and multiple structural conditions are involved.
This allows the user to choose steel sections from the available in-built steel tables for
different countries. The Steel Table option provides a sub-menu that includes available
countries steel table types. Select the country from this sub-menu. Please note that the
Properties dialog box also opens simultaneously letting us utilize some of the other options
available from the dialog box. After choosing the country, the Steel Table dialog box appears
as shown below:
Select the type of section by clicking on the appropriate tab and then select the specific
section from the list box. Please note that the type of steel section available for selection will
vary depending on the selected country. In addiction, depending on the type of section
selected, additional properties may be specified. Click Add button to add this property to the
structure or click Assign to assign the property to the selected members as well as add this
property to the structure.
Click on the View Table button to display all the available dimensions in the active database
for the sectional cross-section. This option displays all member properties for the current
country steel table in a dialog box and provides the feature to customize steel section
database.
User is provided with the following two options in the dialog box:
Select Single Section Where user can select the section for the structural member
6. Click File menu Merge Model with STAAD.Pro Model and place the model at origin.
7. Now assign Fixed support to the structure.
8. Assign the Member Property for column as YD=0.6 m & ZD= 0.6 m and for beam YD=
0.75 m & ZD= 0.6 m.
12. Now Add New : Seismic Definitions dialog box appears, in Type drop down box select the
respective codes for design. i.e IS 1893 2002/2005
13. Click Generate button, now the IS 1893 Seismic Parameter dialog box appears.
Importance Factor,
Type of soil.
14. Click Generate button. In IS 1893 Seismic Parameter dialog box type the Damping Value
as 0.05. Click Add button.
15. Now your seismic definition is added, then add other factor of seismic definition. First
you have to add the basic factors.
Floor Weights must assigned as given below and click Add button.
16. Now you are going to add the Load Case Details.
17. Load Case Type 1 ( Here you assign floor loads only in GY direction and values must be
negative.)
LOAD CASE 1
18. Load Case Type 2 Response Spectrum (Here you add the self weight of the structure in
positive X and Z direction and negative Y direction. Different floor load in all three global
directions.)
LOAD CASE 2
FLOOR LOAD
19. Now you have to assign the self weight to structure by Assign to view.
20. Then add another load item Response Spectra as shown below.
21. Then Click Commands Miscellaneous Cut Off Mode Shape. Mode Shapes
Value is 10.
25. Deflection:
6. Click File menu Merge Model with STAAD.Pro Model and place the model at origin.
7. Now assign Fixed support to the structure.
8. Assign the Member Property for column as YD=0.6 m & ZD= 0.6 m and for beam YD=
0.75 m & ZD= 0.6 m, Plate Thicness = 0.15m.
15. Again Run Analysis. Now you get the Rayleigh Frequency for load case 1 and load case 2.
16. Then check the deflection using Animation command. Provide suitable concrete
design the control the deflection.
6. Click File menu Merge Model with STAAD.Pro Model and place the model at origin.
7. Now assign Fixed support to the structure.
8. Assign the Member Property for column as YD=0.6 m & ZD= 0.6 m and for beam YD=
0.75 m & ZD= 0.6 m, Plate Thickness = 0.15m.
17. According to IS 1893, Mass Participation Factors must be atleast greater than 90.
19. Now you have to provide the suitable concrete design to control the deflection.
Note: For more info and further details watch the video.
Chapter- 11: (Wind Load Intensity Worked Examples)
1. Calculate Wind Load Intensity In A Building
4. By using the Snap/Node Beam Add the members and select the members.
5. Now use the Translational Repeat option to build the structure.
10. Now click Calculate as per ASCE-7 button. Now the select respective code and type of
building. Click OK
11. Wind load in calculated according the varying height of the structure. Click Close button.
19. In Post Processing, You can get the Bending Moment and Shear Force values.