You are on page 1of 5

Name: ........................................... ..............................

Roll No. : ....................................... ...............................


Invigilators Signature: .................................................
CS/B.TECH/CE (NEW) /SEM-6 /CE-602/2015

2015
DESIGN OF STEEL STRUCTURE
Time Allotted : 3 Hours

Full Marks : 70

The figures in the margin indicate full marks.


Candidates are required to give their answers in their own words
as far as practicable.

GROUP A
( Multiple Choice Type Questions )
1.

Choose the correct alternatives for a ny ten of the following :


(10x1=10)
i)

ii)

iii)

The minimum spacing of a bolt of diameter 20mm is


a)

20 mm

b)

30 mm

c)

50 mm

d)

40 mm

For a HSFG bolt of grade 10.9 u ltimate stress of bolt is


a)

400 MPa

b)

1040 MPa

c)

900 MPa

d)

None of the above

For a tension member other than pretension member, which is not


subjected to any reversal of stress, maximum slenderness ratio is

iv)

a)

180

b)400

c)

350

d) 250

For fillet weld subjected to normal stress ( f ) and shear stress (q)
equivalent stress is given by
2

a)

( f + q )

c)

(3f + q )

b) ( f + 3q )
d) None of these

[Turn Over

CS/B.TECH/CE (NEW) /SEM-6 /CE-602/2015


v) As per IS:800 for a plate girder with vertical and horizontal stiffener,
the greater and lesser unsupported clear dimens ion of a web panel
of web thickness tw, should not exceed respectively

vi)

a) 180 tw and 85 tw

b) 270 tw and200 tw

c) 270 tw and 180 tw

d) 400 tw and 250 tw

When the gantry girder is subjected to impact load for electrically


operated crane, horizontal force transverse to the rail is
a) 5% of (weight of crab +weight lif ted)
b) 55% of static wheel load
c) 10% of static wheel load
d) 10% of (weight of crab+ weight lifted )

vii)

viii)

A beam column flexible connection is expected to resist and transfer


a) only moment

b) only shear

c) both moment and shear

d) 50% of moment and shear

Intermediate vertical stiff eners are provided in plate girder to


a) eliminate web buckling

b) eliminate local buckling

c) Transfer concentrated load d) Prevent excessive deflection


ix)

The slenderness ratio of a single angle single bolted strut should be


less than

x)

xi)

a) 180

b) 250

c) 300

d) 350

Minimum number of battens required in a built up column are


a) 2

b) 3

c) 4

d) 6

If the outstand element of compression flange of a rolled section


is less than
a) 8.4

b) 9.4

c) 10.5

d) 15.7

[Turn Over

CS/B.TECH/CE (NEW) /SEM-6 /CE-602/2015


xii)

As per IS specifications, the beam sections should be


a) At least symmetrical about one of the principal axe s
b) Symmetrical about both the principal axes
c) Rolled to furnish maximum sectional modulus
d) All the above

xiii)

The deflection of steel beams in buildings other than industrial building


is limited to a span is divided by
a) 180

b) 250

c) 350

d) 325

GROUP B
(Short Answer Type Questions)
Answer any three of the following

3x5=15

2. A circular penstock of Steel grade Fe 410 is of diameter 1.2 m. It is fabricated


In workshop from 12 mm thick plate. The two ends of the plate are secured by
8 mm fillet weld both inside and outside of the lapped end. Determine the safe
internal pressure that can be allowe d in the penstock .
3. An angle ISA 150x115x8 mm of grade Fe 410 is connected to a gusset plate.
It is welded with length 100 mm at both heel And toe and 150 mm at the
connected leg. Calculate the tensile strength of the angle for a) gross section
yielding b) Net section rupture.
4. A gantry girder consist of ISWB 600 with ISMC 300 o n its top with flanges
downward. Find its section modulus for vertical load.
5. Design a slab Base for column ISHB300@577N/m carrying an axial factored
load of 1000 KN. M20 concrete is used for the foundation. Provide welded
connection between column and base plate.

[Turn Over

CS/B.TECH/CE (NEW) /SEM-6 /CE-602/2015


6. SC 200 is used as a column shown in figure. The column is laterally supported
in the plane of the major axis at the height of 3.5 m and in the plane of minor axis
at the height of 2.5 m. Both the end may be assumed as hinged. What is the
design load carrying capacity of the column. Grade of steel is Fe250.

Given data:

d : 200mm , bf : 200 mm , tf : 15 mm

GROUP C
(Long Answer Type Questions)
Answer any three of the following

3x15=45

7. a) Two plates of grade Fe 410, thickness 18 mm and 10 mm thickness are


to be joined by double cover butt joint with 20 mm diameter bolt of grade 4.6.
Thickness of cover plates are 8mm and factored Design load is 750 KN.
Design the Joint.
b) Design a double cover butt joint to transmit working load of 300 KN to
connect two flats 120 mm wide and 20 mm thick using 16mm diameter
HSFG bolt of grade 10.9 if i) Slip is not permitted at working load
ii) Slip is not permitted at a ultimate load.
8. A bracket plate 10 mm thick is used to transmit a reaction 140 KN at an

[Turn Over

CS/B.TECH/CE (NEW) /SEM -6 /CE-602/2015


eccentricity of 100 mm from column flange. Design the welding between
bracket plate and column flange using i) double groove weld ii) fillet weld
9. A welded plate girder 24 m in span and laterally restrained throughout has
to carry a UDL 100kn/metre exclusive of self weight. Design the girder
without intermediate transverse stiffner. Using Fe 410 grade of steel design
the cross section, end load bearing stiffner.
10. Design a gantry girder for an industrial shade carrying a manually
operated overhead traveling crane from following data
a) Crane Capacity: 200kn
b) Self weight of Crane girder exclusive trolley: 200kn
c) Self weight of trolley with accessories: 40 KN
d) Minimum approach of crane hook to the gantry girder: 1.2m.
e) Wheel base: 3.5 m.
f) Centre to center distance between gantry rail: 16 m.
g) Span of gantry girder: 8 m
h) Self weight of rail 300n/m
i) Diameter of Crane Wheel : 150mm
Steel is of grade Fe 410.
The support bracket connection need to be designed.
11. Design a built up column 10 m long to carry factored axial load of
1100 KN. The column is hinged at both end s. Provide single lacing system
With two channels back to back and welded connec tion for lacing system.
Assume steel of grade Fe 410.
12. Design a laterally supported beam of effective span 5 m for the
following data
a) Grade of steel Fe 410
b) Max. bending moment 200 KN-M.
c) Max. shear force 250 KN.

[Turn Over

You might also like