Professional Documents
Culture Documents
Edition 02/02/2012
Identification no:
02 07 04 99 900 0 000027
Sika WP Shield-104 P
Sika WP Shield-104 P
Construction
Uses
Characteristics /
Advantages
Alternatively can be over coated with two coats of Sika Raingard acrylic based
single component white coating system for obtaining cooling effect incase
screeding is not to be done. This also improves UV ray stability of the
membrane
Tests
Approval / Standards
UEAtc M. O. A. T. 30, ASTM D 36, ASTM D 5, ASTM D 5147, DIN EN 52123, DIN
EN- 12311- 1, DIN EN 12310-1, ASTM E 154, DIN EN 1107-1
Sika WPShield-104 P
1/3
Product Data
Form
Appearance / Colours
Black membrane
Packaging
1.0 x 10 m roll
Storage
Storage Conditions /
Shelf-Life
Rolls must be stored in their original package, in horizontal position and under cool
and dry conditions. They must be protected from direct sunlight, rain, snow and ice,
etc. Should be stored vertically in clean covered one. Rolls should be etched.
Technical Data
Chemical Base
Thickness
4mm
Unit weight
4.2 kg/m
Mechanical / Physical
Properties
Tensile Strength (L/T)
N/5cm
650/350
30/45
Resistance to water
pressure
No leakage
Water Absorption%
<0.20
160 gm/m
o
Softening Point
>145 C
o
Penetration at 25 C
15- 25mm
Tear resistance
(L/T)N/5cm
180/200
(According to ASTM D 36 )
(According to ASTM D5)
(According to DIN EN 12310-1)
No Flow
Puncture Resistance
>550N
Dimensional Stability %
<0.3
System
Information
Application Details
Substrate Quality
Concrete, mortar surfaces must be clean, free from grease, oil, and loosely
adhering particles. Steel and iron surfaces must be free from scale, rust, grease
and oil. All surfaces must be as true as possible.
Application
Conditions /
Limitations
Substrate Temperature
Ambient Temperature
Sika WP Shield-104 P
2/3
Application
Instructions
Application Method /
Tools
Application procedure may vary slightly depending upon site conditions. However
given below are general guidelines.
Apply bituminous / water based primer to a clean, smooth and dry surface by brush,
roller or spray. Allow the primer to dry to become tack free. Unroll and align and re
roll correctly before torching. Overlaps should be minimum 100mm.Use gas burner
to heat the substrate and thermo fusible film on the underside on lower face of
membrane. When the thermo- fusible film melts after torching, the membrane is
ready to stick. Roll forward and press firmly against the substrate to bond. Heat
both the overlaps and use the round tipped trowel heating the same to smoothen
and press into seam. Side overlaps should be a minimum of 100 mm and end
overlaps 150 mm
Construction
All angles and abutments should be sealed with extra care to ensure full bondage.
The edges should be sealed well into the grooves.
The membrane should be protected from getting damaged due to ongoing site
activities and during backfilling either by cement sand plaster or other suitable
methods using Sikacim / Sika Plastocrete Super. Before laying the screed apply a
layer of the same primer and sprinkle sand for obtaining shear key and allow it to
dry completely.This not only improves the UV ray stability of the membrane but also
provides better bonding.
Alternatively apply two coats of Sika Raingard acrylic based single component
white coating system for obtaining cooling effect and also to improve the UV ray
stability of the membrane
Value Base
All technical data stated in this Product Data Sheet are based on laboratory tests.
Actual measured data may vary due to circumstances beyond our control.
For information and advice on the safe handling, storage and disposal of chemical
products, users shall refer to the most recent Material Safety Data Sheet containing
physical, ecological, toxicological and other safety-related data.
Legal Notes
Phone
+91 33 2447 2448/2449
Telefax +91 33 2396 8688
ind.sika.com
info.india@in.sika.com
Sika WP Shield-104 P
3/3