Professional Documents
Culture Documents
ffiFAEtffig
DISPLACEMENT TRANSDUCER TEST DATA
4&
EE
Capacity
iH. r*.
CDP_s0
TYPe
F{ffi+E
2012.10.30
Date
50
rur=*6+
mm
BBD121629
Humidity
37%
iEE
23r
Temperature
Serial No.
-5000 ttY,/Y
trlf&fr11:Rated output
_10000 X 10-"
(0f4:Strain K:2.00)
>k***
: No n
lin
,AHrffi+Ffiffifift
earity
:
Input
L)r
& output resistance
Input
0.3
cable
^frhf-),rL:Connection
tJtilEBr,t EF
350.8
1000
T140-8560
0.00500
frh-
0.1
output 348.9
mm
/1x
10-6
%R0
O
M 0 D_II(DC5OV)
mm
20
F,tt#
HiRlI
HHflft/lltrffit#O-a-2
E 6ff
AFfi
TEL (03)3763-5611
Supervised by
ZT\
l*ol
\E/
adffiE.
Tested by
@-1
TCAII-OO(]
CDP
Please be sure to read the manual before use and retain it together with test data.
1.
DIMENSIONS
CDP-5
99
20
24
10
10
t0
t0
28
90
99
20.5
20.5
20.5
33.5
cDP-l0
28
-d6
10
2A
'5"
90
65
10
10
35
118
12
36
270
580
Tvpe
CDP-25
2.
114
cDP-s0
.154
CDP-IOO
214
41
'f(,
Weieht(e)
INSTALIATION
Fit the supplied fixing holder to the body of the unit (use two holders for CDP-50 and CDP-100)
and tighten thc supplied screw. Pay attention not to excessively tighten it. Recommended tightening
torque is 0.7N ' m (7kgf ' cm) or less. Refer to the graduation on the shaft or the measurement value
of a measuring instrument for positioning.
Make sure that the direction of displacement to be measured coincides with the axial center of the
CDP unit.
As the shaft docs not move in excess of the rated capacity, takc care that it should not be
excessively pressed down. When exchanging the contact tip, take care of looseness of thc tip
because the shaft rotates.
Do not fix the shaft direct to the test object. Do not release quickly from the state of the shaft
beingirlly
pressed down; otherwise the CDP unit may be damaged by spring reaction.
IG
3. MEASUREMENT
The CDP unit is calibrated with a constant voltage excitation type strain meter using the supplied
The rated output and scnsitivity shown on thc test data are found with an instrumcnt gauge
factor of 2.00. ( In case of using TML data logger, its coefficient should be set to 1.000. )
cable.
One end of the supplied cable does not usually have a connector plug. the cable is connected to
a strain meter or its switching box by screwing or soldering. In case of using NDIS 7-pin plug
refer to the following connection layout.
atraircter
cnr.r
,T
(-) B c>-
ffi{r (+)
po-
RED (+)
ACF-
BrI< (-)
S}IIELD
'
c Cr-e O--
N.B.The shield wire of the cable is not connected to the body of the CDP unit.
S"t necessary measuring'parameters to a strain meter, recorder, computor, etc. ( for strain meter,
for instance, initial balancing, sensitivity adjustment, setting of unit, coefficient and measure mode
initial value measurement, ctc.)
In ordinary measutement, it is recommended that a strain meter is previously set to direct measure
mm. In case of reading strain, displaccment is calculated using the following equation:
mode in
Displacemcnt
Measured value
lmml
I x10'6 ]
Calibration coefficient
I mm,/lxto-61
(x lQ't.
(-m) by the
rated
When the shaft is pressed down, thc measured value changes in negative polarity. 7*ro
adjustment of this unit is made at thc state of the shaft being pressed approximately halfway.
In ca!" the length.of cable is extended, you must correct the lowering of sensitivity using
'(N.B.
following equation:
Equation
where
o:
t:
R_
r:
: Eo :
{ t +_
voltagi)
correction
[mm]
I.,,'
(O)
[p
| fi
t f)
0.05
0.09
0.3
0.35
0.5
0.63
0.40
0.il9
0.1 06
0.071
the
TCAH-()O()1
4.
CAUTIONS
If
Do not grease the shaft and bearing. Take care that the shaft is not hurt, bent excessively pressed
down; otherwise, operation failure will be caused. Ifthe shaft is quickly released from the state of
the shaft being pressed down, the unit may be damaged due to reaction
Do not forcedly bend the cable near the cable intake. Do not place an object on the cable, nor
pull nor flaw the cable.
The CDP unit has no hermetically sealed construction (bearing, cable intake section, etc.),so take
care that water or oil does not permeate from the end of cable.
Continuous use with a bridge excitation voltage over recommendation may produce drift and as a
result, performance will become out of specifications.
Rcommndcd brilgc c)ail8tiotr
Less than 2V
10v
In case of using other instrument than strain meter, make sure that excitation voltage is very stable
5.
ClIECKand STORAGE
Make sure that the value [X 10'6] measured in DIRECT mode of the strain metor with the shaft
being pressed halfiray is not excessively large.
Using an insulation resistance tester with an excitation voltage of DC 50V or less, measure
insulation resistance [M0] betrveen input/output wires of the cable (4 wires of red, green, black
and white ) and the CDP unit body to confirm that the insulatiou resistance is kept at about
1000MfJ or more.
Using a digital voltmeter or tester, measure terminal resistance [ 0 ] between output wfues (red and
black) and input wires (green and white). Make sure that the measured value is not largely
different from the value shown on the test data sheet.
For storage, avoid a high or low temperature, high humid place, dust, water drop, vibration, shock,
etc. Handle the supplied cable as well but with a cable cap put.
r,Tqii":'dati;
'-
lcspy,,
Fffi:Tlff"
' Cabte
:
cable lOm
i.,
ktf#g*F::,"=,a:.':4
lr*r',1,*;',ir+.,#:ifu,6$g:;:
:...)l:
i.
'::',
: l:::t,;,,-
,i,i ii.i$iJ:l
:
+iii
:..i,1.
''=*rr,,,gtg;;';!
::1 r,:i
i*s:*i-,:
': ES-@q$ffi*S'&dryg;4.6gg,*E;co.,'.,
"- .-- : .: -:
TEL
URL
"-\'i_i.:.,.
,.'
81ri:r763-j6tr
vrww.tmt.ip/e
FA:( 8r-3-3?f*i571.3f::ii,,
E
mail salesotml.jp
ni-Jt
-:--