Professional Documents
Culture Documents
Group T8
Muhammad Ramdhan bin Mohd Suhaili
Muhammad Nurhidayat bin Muhtaza
Muhammad Luqman bin Azmer
Muhammad Izzuddin bin Abdullah
Abstract-These experiment contain two
different cases. Case 1 experiment are to
investigate the electrostatic characteristic of
the stress film that has been used widely as
wrapping material. The electrostatic charge
contain on surface of stress film can be
harmful to the electronic components. The
experiment are successful and the result are
same as the theory of electrostatics. There are
movement of electron on the surface cause the
form of induce charge. While for case 2
experiment, five types of hair fiber were given
to find best hair fiber based on their magnetic
characteristics. Then a solenoid are used to test
each hair fiber by using magnetic field sensor.
However based on the formula, the result are
varied current values, number of turns and
length of wire wrapped used are manipulated.
From theory, magnetic field also effect by
permeability of magnetic material,r used.
Case 1: Electrostatic for stress film.
Introduction
Stress film are widely use to wrap the product
from factory to avoid from damage. But,
electronic components such as IC are very
sensitive to the stress film. Electronic
component can be easily damage effect of the
electrostatics charge on stress film. These task
will test two difference condition of stress film
which is rubbed and unrubbed stress film
and normal plastic. The induce charge will be
measure by using Faradays Cage, charge
sensor and LabQuest equipment. The charge
density can be measure by using specific
formula.
Procedure.
1. Setup the equipment properly.
2. Firstly, put the metal rod to clear the
charge inside the Faradays cage.
10
20
30
40
-0.5
-1
-1.5
Time (s)
0
5
10
15
20
25
30
Charge(nC)
-1.667
-1.099
-0.755
-0.595
-0.528
-0.531
-0.366
= -0.792 nC/s
0
0
10
20
30
40
1.5
-0.5
-1
0.5
0
-1.5
10
20
30
40
-2
Time (s)
0
5
10
15
20
25
Charge(nC)
-1.767
-1.011
-0.7
-0.556
-0.439
-0.4
= -0.6961 nC/s
= 0.719 nC/s
0
0
10
20
30
40
0
-0.5
-2
10
20
30
40
-1
-4
-1.5
-6
Time (s)
0
5
10
15
20
25
30
-2
Charge (nC)
-5.265
-2.837
-1.894
-1.428
-1.192
-1.053
-0.922
-2.5
= - 2.084 nC/s
For unrubbed normal plastic
= -1.299 nC/s
Discussion
From table, it shows that the rub stress film
give a negative value of induced charge.
During the rubbing process the electron from
cloth are moving to the stress film.in this case,
0.792 nC/s
= =
1.8 x 103 2
= - 440nC/m2
The cloth that used for rubbing the stress film
are positively charge based on the graph from
LabQuest as shown below. It is because of the
electron in cloth are transfer or move to stress
film.
Unrubbed plastic
s = 0.719 / 1.8 x 10-3 =399.44 nC/m2
Rubbed plastics:
s = -1.299 / 1.8 x 10-3 =-721.67 nC/m2
From data above, charge density normal
plastic are low than stress film stress film and
normal plastics are not suitable to use as
wrapping film for electronic components
because the stress film have high tendency to
gain electron. It can gain electron from the
Procedure
Capacitance,
C(F)
Nanogen
XFusion
Toppik
SMH
BioThik
0.57n
0.56n
0.56n
0.58n
0.70n
Hair Fibre
Types
Current (A)
Number of Turns
(N)
Length coil (L)
Amount Hair Fibre
Air
Nanogen
SMH
Toppik
XFusion
Biothik
Voltage
across cavity,
V
27.1m
24.6m
47.8m
41.8m
46.5m
Charge, q(C)
Charge
density,
21.03n
22.8n
11.7n
13.9n
15.1n
0.74m
0.81m
0.41m
0.49m
0.53m
Large
0.0059
0.3710
0.3408
0.3179
0.3388
0.2866
Dielectric
permittivity,
2.01n
1.98n
1.98n
2.05n
2.48n
3
15
1
25
0.034
Small
0.034
Small
0.053
Small
0.7044
1.1718
0.5066
Magnetic Permeability, r
(wb)
13.3733
0.1250
0.1316
0.1316
0.1426
0.1410