Professional Documents
Culture Documents
MEE 3220
FLUID MECHANICS 1
EXPERIMENT 1
MEASUREMENTS OF
HYDROSTATICS FORCE
Name
ID
EHSAN SAMOH
DONYEGHA TUNEMI
Albert Law Lee Tai
I14005275
I13003778
I14004759
Objectives
i. To determine the hydrostatic thrust acting on a plane surface immersed in water.
ii. To determine the position of the line of action of the thrust and to compare the position
determined by experiment with theory.
1.2
p at a point
p=gh ,
rectangular plane vertically immersed in the given fluid, we can obtain the force due to fluid
pressure on each element of area A . Since we know from the definition of pressure that,
p=
F
A
F=pA . Substituting
p=gh
and
A=A ,
Summing up all the forces on all elements of area over the immersed rectangular plane, we
have the resultant force,
R= ghA=g hA=g h A
hA =h A
The quantity
where
kO
is the radius of gyration of the immersed surface about the axis where the
extension area of immersed surface meets the free surface of the fluid, and
is the angle
between the immersed surface and the free surface. For a partially or exact wholly, vertically
immersed rectangular plane, =90 , sin 90 =1 ,
I O I G + A h2 A k G 2+ A h2
2
2
kO = =
=
=k G + h
A
A
A
2
h
h
( k G + h 2 )(12) 12 +( 2 ) 2
D=
=
= h
h
h
3
2
2
This equation indicates that the distance of center of pressure measured from the fluids free
surface is two-third of the height of immersed vertical rectangular surface. That is also
where the resultant force due to fluid pressure acting on the plane.
Since we now can simplify the pressure forces on a given surface immersed in a
fluid with known value of density, it would be much easier to analyse the static equilibrium
condition of the mechanism shown in the experiment below.
The apparatus shown above is the hydrostatic pressure apparatus. The main parts of
the apparatus are the pivot, quadrant, weight hanger and the counterbalance. The position of
pivot relative to the quadrant is very important to the accuracy of this experiment. The pivot
is mounted on the balance arm where coincides with the center of arc of the quadrant. Since
we know that a fluid at rest will not be having any shearing forces and all the forces in the
fluid must be perpendicular to the surface in contact, which is the surface of the quadrant, in
this case. The line of action of the forces will definitely pass through the pivot. In order to
create a moment on the balance arm, there must be forces acting on the quadrant and
moment arm which is the perpendicular distance from the line of action of the force to the
pivot. As a result, all the elementary pressure forces acting on the curve surface of the
quadrant will not generate a significant moment upon the apparatus, and therefore the
apparatus will not rotate about pivot P.
If the fluid, say water, is poured into the tank and the quadrant is partially immersed
in the water, when taking the moments about pivot P, only the effects of the pressure force
on the end face of the quadrant and the weights added need to be considered as the pressure
forces on the curve surface will not create any moment or only create a moment that is
sufficiently small to be neglected. The moment arm of both fluid pressure force and weights
can be measured directly before carrying out the experiment.
Since the whole system is in static equilibrium, the algebraic summation of all the
moments acting on the system should be equal to zero, which can be expressed in
mathematical expression
M =0
determined by equating the counter-clockwise moments and the clockwise moments, while
the experimental values of the hydrostatic force can be determined using equation
R= g h A . The height of the immersed part of the quadrant can be determined from the
scale on the side of the quadrant. Note that the counterbalance will also generate a moment
about pivot P, and since its weight and moment arm are constant, its moment should be a
constant value as well.
Figure 1.3 The scale can be used to measure the height of the immersed part of the quadrant.
1.3
Procedures
1. Before carrying out the experiment, one ensured that the fluid tank of the hydrostatic
pressure apparatus is on the horizontal water level by checking the circular spirit level
mounted beside the fluid tank.
2. The dimensions of the quadrant end-face (both length and width), the distance between
the pivot and the weights and the distance between the pivot and the bottom of the
quadrant were measured directly on the apparatus.
3. The position of the counterbalance and the number of weights were adjusted according
to level indicator in order to balance the arm to horizontal position. (The fluid tank was
empty.)
Figure 1.4 The level indicator on the end of the balance arm
4. The drain valve was closed before pouring water into the tank to avoid water from
draining out of the tank.
5. Extra weights were added progressively, in our case the weight was added 20g every
time, initially 120g.
6. A certain amount water was added (water level should at least reach the minimum level
of the height scale on the side of quadrant) to balance the arm back to horizontal
position, and the height of water level was taken down.
7. Step 5 and 6 was repeated until the water level reaches the top of the water level scale.
8. Then the procedures were repeated reversely, the height of remaining water was
recorded for every time 20g of weight was removed.
9. The experimental data were recorded and tabulated in the Results and Calculations part.
1.4
360
380
400
420
123
128
133
138
3.532
3.728
3.924
4.120
We can find the resultant force due to water pressure by using equation R= g h A . This
equation can transform into a more convenient expression. When the water poured in was
1
immersing the end face of quadrant, h= 2 h and
R= g h A=g
( h2 ) h d = 12 g h d
2
A=h d 3 , which is
d3
, gravitational acceleration
R is directly proportional to h
, that is
R h
h=h
=h0.049 , therefore
2
h>9.8 cm ),
R= g ( h0.049 ) d 3 d 4 .
83
89
94
99
104
109
113
118
123
128
133
138
2.636
3.030
3.381
3.749
4.124
4.499
4.799
5.174
5.549
5.924
6.299
6.674
When the water is immersing the end face of the quadrant, the distance from the free
surface to its center of pressure is
2
h based on the derivation in the Introduction and
3
1
Theory part, and therefore the moment arm of resultant force is d 2 3 h .
After the end face of quadrant is wholly immersed, the distance of center of pressure
from free surface of water can be derived as below:
kO2
D=
h
Since
2
k O 2=
I O I G + A (h0.049)
=
=k G2 +( h0.049)2
A
A
2
0.098
+(h0.049)2
k G 2+(h0.049)2
12
0.0982
D=
=
=
+h0.049
h0.049
h0.049
12h0.588
Water Level, h
(mm)
83
89
94
99
104
109
113
118
123
128
133
138
D (m)
0.055
0.059
0.063
0.066
0.070
0.073
0.077
0.081
0.085
0.089
0.094
0.098
Moment Arm of R
(m)
0.183
0.181
0.180
0.178
0.177
0.175
0.175
0.174
0.173
0.172
0.172
0.171
Resultant
Force, R (N)
Weight, W
(N)
Moment of R
(Nm)
Moment of W
(Nm)
2.636
3.030
3.381
3.749
4.124
4.499
4.799
5.174
5.549
5.924
6.299
6.674
1.962
2.158
2.354
2.551
2.747
2.943
3.139
3.335
3.532
3.728
3.924
4.120
0.483
0.550
0.607
0.667
0.728
0.789
0.837
0.898
0.959
1.020
1.080
1.141
0.540
0.594
0.647
0.701
0.755
0.809
0.863
0.917
0.971
1.025
1.079
1.133
1.5
Discussions
Based on the water level versus resultant force table presented above, we can plot a
graph to represent their relationship.
Resultant Force R / N
4.5
4
3.5
3
2.5
2
80
90
100
110
120
130
140
From the diagram and the relationship equation derived in previous part, the water
pressure resultant force (acting similar to upthrust) and depth of water level can be described
approximately linked by a linear relationship (even before h = 9.8cm the relationship
between R and h is binomial
1
R= g h2 d 3 , however the slope of the binomial curve
2
doesnt change much, and therefore can be treated as approximately linear). Based on the
graph, the slope of the best-fit line is approximately the same based on the data points
collected. From the scatter diagram above, we can conclude that as the depth of water level
increases, the resultant water pressure force increases proportionally to the increase in depth
of water level.
Except of the resultant force R, the depth of the center of pressure is also affected by
the depth of immersion. We know that before h = 9.4cm, the center of pressure is always
two-third of depth of immersion measured from the free surface of water. However, the
relationship
between
these
two
becomes
complicated,
which
is
0.0982
D=
+h0.049 . The relationship is graphically represented in the graph
12 h0.588
shown below.
Relationship between Depth of Center of Pressure (D) and Depth of Immersion (h)
0.1
0.09
0.08
90
100
110
120
130
140
Depth of Immersion h / mm
Based on the graph above, the relationship between D and h is to be more likely a
binomial or exponential trend. As the depth of immersion increases, the depth of center of
pressure will increase, and its rate of increase is getting faster as well since the slope of the
curve is becoming greater.
And we also looked into the experiment to check the discrepancies between
theoretical and experimental results obtained. Back to the table where we compare the
moments generated by resultant upthrust force and the weight.
Moment of R
(Nm)
0.483
0.550
0.607
0.667
0.728
0.789
0.837
0.898
0.959
1.020
1.080
1.141
Moment of W
(Nm)
0.540
0.594
0.647
0.701
0.755
0.809
0.863
0.917
0.971
1.025
1.079
1.133
Discrepancy
(Nm)
0.056
0.044
0.040
0.034
0.027
0.020
0.026
0.019
0.012
0.005
0.001
0.008
We know that in the reservoir of water dam, as the head from the water surface
increases, the water pressure will increase according to the formula p=gh where h is
the head of a point in the water contained. Therefore, the deeper it goes, the wall of the dam
should be built thicker in order to withstand the hydrostatic force caused by the water
pressure. We know that the pressure force on a flat surface immersed in fluid will be parallel
to each other, and add up to become greater in magnitude if they are in the same direction. If
the surface is curved, every elemental pressure force are pointing at different direction, and
therefore they will cancel each other partially (or even wholly cancel each other if the
surface is circle in shape). This concept is also applied in building a dam, for example the El
Atazar Dam near Madrid. This kind of design is known as arch dam. An arch dam is
designed so that the pressure force of water will partially cancel each other and also press
against the arch to compress and strengthen the dam structure. It is more suitable in narrow
gorges or canyons, and since it requires less construction materials, it is more economical
and practical in remote areas.
1.6
Conclusion
This experiment gives a moderate accuracy to measure the pressure force on the end
face of quadrant. The key concept of this experiment is to know that since the balance arm is
in equilibrium before pouring in water, the moment created by the water pressure force on
the end face of quadrant should be equal to the moment created by weights. And since the
pressure force on the curve surface will not create any moment on the system about pivot, it
needs not to be considered. As the water level increases, the resultant pressure force and its
center of pressure will vary as well. To improve the accuracy of this experiment, the weight
should be weighed in advance to confirm its actual weight value. Besides, this experiment
can also be done by replacing water with other liquids, such as alcohol with known density
to compare the experimental results obtained.
1.7
References
1. Displacement (ship) - Wikipedia, the free encyclopedia. 2014. Displacement (ship) Wikipedia, the free encyclopedia. [ONLINE] Available at:
http://en.wikipedia.org/wiki/Displacement_(ship).
2. Arch dam - Wikipedia, the free encyclopedia. 2014. Arch dam - Wikipedia, the free
encyclopedia. [ONLINE] Available at: http://en.wikipedia.org/wiki/Arch_dam.