You are on page 1of 330

DOCUMENT NO:

60-0000-L-SPE-0002
DOCUMENT TITLE:

SPECIFICATION FOR
PIPE SUPPORTS

ДОКУМЕНТ №

60-0000-L-SPE-0002
НАИМЕНОВАНИЕ

XXXXX

TENGIZCHEVROIL
PFD Project No. 571500

ТЕНГИЗШЕВРОЙЛ
PFD Проект № 571500

4 29/06/05 22 RE-ISSUED FOR CONSTRUCTION PO BW SM RH

3 12/07/04 21 RE-ISSUED FOR CONSTRUCTION PO BW SM DB

2 28/01/04 21 RE-ISSUED FOR CONSTRUCTION PO BW MB DB

1 10/04/03 19 RE-ISSUED FOR CONSTRUCTION PO BW MB JH


0 22/08/02 18 ISSUED FOR CONSTRUCTION PO BW MB JH
REV DATE PAGES DESCRIPTION BY CHKD APPR CLIENT
ИЗМ. ДАТА СТР. ПОЯСНЕНИЯ ИСП. ПРОВ. УТВ. ЗАКАЗЧИК

Pagee 1 of 22
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
PROJECT №. 571500
SPECIFICATION FOR PIPE SUPPORTS DOC №. : 60-0000-L-SPE-0002
Rev. 4

REVISION DESCRIPTION SHEET

REV. PARA. REVISION DESCRIPTION


4 4.2 NSPS MATERIAL REVISED
COLD CONSERVATION INSULATION THICKNESS TABLE
4 8
REVISED TO INCLUDE COLD PERSONNEL PROTECTION
4 10 NOTES REVISED
ATTACHMENTS
SHEET NO.
4 A15, A18 PIPE SIZE RANGE REVISED
4 A32 SUPPORT NUMBER REVISED
4 A34 - A36 NEW PIPE SUPPORTS
4 B7 PIPE SIZE RANGE REVISED
4 B50 - B57 NEW PIPE SUPPORTS
4 C3 PIPE SIZE RANGE REVISED
4 C5 SUPPORT REVISED FOR TRUNNION SIZES 18” - 24”
4 C12, C13 NOTE ADDED TO DRAWING
4 C15, C18, C19 SUPPORT REVISED FOR TRUNNION SIZES 18” - 24”
4 D30 - D34 NEW PIPE SUPPORTS
4 E40 NOTE REVISED
4 E44 DIMENSION REVISED
4 E51 NEW PIPE SUPPORT
4 F16, F20, F21 PIPE SIZE RANGE REVISED
4 F32, F33 DIMENSION REVISED
4 F36 – F39 PIPE SIZE RANGE REVISED
4 F40 DETAIL REVISED
4 F43 – F49 NEW PIPE SUPPORTS
4 G12 THREADED BAR LENGTH REVISED
4 H9 TRUNNION END PLATE REVISED
4 H23, H24 DIMENSION REVISED
4 J1- J13 GENERAL REVISION OF SELECTION SHEETS

Pagee 2 of 22
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
PROJECT №. 571500
SPECIFICATION FOR PIPE SUPPORTS DOC №. : 60-0000-L-SPE-0002
Rev. 4

TABLE OF CONTENTS

1. SCOPE 4
2. CODES, STANDARDS AND SPECIFICATIONS 4
3. ABBREVIATIONS 4
4. PIPE SUPPORT CATEGORIES 4
5. GENERAL NOTES 5
6. MAXIMUM PIPE SPANS 6
7. MAXIMUM GUIDE SPACING 10
8. PIPE SHOE HEIGHTS 11
9. ALLOWABLE LOADS FOR NON-INSULATED PIPES, PIPE SHOES,
PIPE ANCHORS 13
10. PROCEDURE FOR INSTALLATION OF ANCHOR BOLTS AND GROUTING OF
BASE PLATES 15

ATTACHMENTS

A. SHOES
B. ANCHORS, GUIDES & VERTICAL PIPE SUPPORTS
C. TRUNNIONS & BASE SUPPORTS
D. HANGERS & SPRINGS
E. STRUCTURAL SUPPORTS
F. SMALL BORE & ANCILLARY SUPPORTS
G. PIPE SUPPORT FOUNDATIONS
H. COLD PIPE SUPPORTS & ANTI VIBRATION SUPPORTS
J. PIPE SUPPORT SELECTION CHART

Pagee 3 of 22
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
PROJECT №. 571500
SPECIFICATION FOR PIPE SUPPORTS DOC №. : 60-0000-L-SPE-0002
Rev. 4

1. SCOPE
This specification describes the general requirements for the selection and design of
Standard Pipe Supports. These include pipe shoes, guides, anchors, hangers, spring
supports, base supports, supports for vertical lines, stainless steel pipes, cold insulated
pipes, small bore pipes (≤ 1 1/2”), structural pipe supports and small pipe support
foundations.

2. CODES, STANDARDS AND SPECIFICATIONS

This specification has been reviewed by the Kazakh Design Institutes and now meets the
requirements of the Kazakh Codes and Standards.

The publications listed below form part of this Specification. Each publication shall be the
latest revision and addendum in effect on the date this specification is issued for
construction UNO. Except as modified by the requirements specified herein or the details
of the drawings, work included in this specification shall conform to the applicable
provisions of these publications.

In the event of a conflict between codes and specifications the more stringent shall apply.

• ANSI/MSS SP-58 Pipe Hangers and Supports, Materials, Design and


Manufacture
• ANSI/MSS SP-69 Pipe Hangers and Supports, Selection and Application
• BS-3974-1 Pipe hangers, slider and roller type supports
• DS-60-W-0045 Welding and NDT Pipe Supports Data Sheet
• 60-0000-L-SPE-0007 Paint & Protective Coatings.
• 60-0000-L-SPE-1003 Purchase Specification for Special Pipe Supports

3. ABBREVIATIONS AND DEFINITIONS

The following abbreviations are used in this document: -

PDS Plant Design System


PTFE Polytetrafluroethylene
TCO Tengizchevroil
TOS Top of steel
UNO Unless Noted Otherwise

4. PIPE SUPPORT CATEGORIES

4.1 Standard Pipe Supports


These shall be used wherever possible and practical, the details of which are shown in the
attachments to this specification. The piping designer shall model standard pipe supports
in PDS Piping, and the support material will be supplied by piping.

Pagee 4 of 22
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
PROJECT №. 571500
SPECIFICATION FOR PIPE SUPPORTS DOC №. : 60-0000-L-SPE-0002
Rev. 4

4.2 Non-Standard Pipe Supports (NSPS)


These are pipe supports that cannot be produced using the standard pipe supports, but do
not require any design input from the Civil engineering group. The piping designer shall
model NSPSs in PDS Piping where they are required for clashing, otherwise they shall be
modelled as a logical. The support material will be supplied by piping.

A support drawing, produced by a pipe supporter or piping designer, shall include the
following information as a minimum: -

• Outline support shape including inset details and sections where required.
• Standard items; e.g. shoes, anchors. Where these items are called up on the isometric
they shall be referenced on the detail.
• Major adjacent civil supplied steelwork.
• TOS elevations, dimensions including dimensions back to grid lines.
• Material Summary.
• Line numbers for supported pipes.
• Welded attachment references back to the isometric.

The pipe supporter shall maintain an index of these supports.

The steel sections used to design the NSPS shall be the same as those used for the
standard supports. These are: -
CS. Plate Thickness: 6, 10, 12, 15, 20
HEA Section: 100, 160, 200
IPE Section: 100, 160, 200
UPN Section: 100, 160, 200
Angle 40 x 6, 60 x 6, 70 x 8, 80 x 8, 100 x 10
Round bar Diameter: 12, 16, 20, 24, 30, 36, 42
SS Plate Thickness: 5

4.3 Civil/Structural Pipe Supports (CPS/SPS)


These are pipe supports that cannot be produced using the standard pipe supports
because: -
(a)- the support dimensions, or
(b)- the support loads
are greater than those specified in the standard supports.

These supports shall be modeled by Piping in Equipment to obtain location and initial
space reservation. Notification of the support details including dimensions, TOS elevation,
support orientation, support loads and pipe sizes will be given to Civil/ Structural. Civil/
Structural shall model this support in ‘Frameworks’ and piping shall remove the support in
Equipment.

5. GENERAL NOTES
• All pipes, including pipes ≤ 1 1/2”, shall be supported.
• Dimensions are in mm.
• All welds are 6mm fillet welds u.n.o.
• Threaded connections are right hand thread u.n.o.
• The allowable axial displacement for shoes is: -

Pagee 5 of 22
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
PROJECT №. 571500
SPECIFICATION FOR PIPE SUPPORTS DOC №. : 60-0000-L-SPE-0002
Rev. 4

±100mm for 300mm long shoes


±200mm for 500mm long shoes
• Adjustable hangers shall only be used in preference to non-adjustable hangers where
the support is: -
(a) Local to a rotating equipment nozzle, (one of the first two supports)
(b) The first support local to a column or vessel.
• The first support local to either pump nozzle shall be adjustable.
• Vertical stainless steel pipes, which require guides, shall have a cradle (C101 or C102)
and a welded shoe if the line is insulated. Clamped shoes shall not be used. Anchor
clamps can be used for galvanised piping.
• Completed pipe supports to be primed and finished coated in accordance with
Specification 60-0000-L-SPE-0007.

6. MAXIMUM PIPE SPANS

From BS 3974 Part 1 (1974) for continuous piping spans,

The Maximum Stress in the pipe (σ) is given by the formulae: -

wDL2
σ=
240 I
The Maximum Deflection in the pipe (δ) is given by the formulae: -

100000wL4
δ=
384 EI
Where: -
σ = Stress (N/mm2)
δ = Pipe deflection (mm)
w = Pipe weight (N/m)
D = Pipe Diameter (mm)
L = Pipe Span for continuous spans (m)
I = Second moment of area (cm4)
E =Young's Modulus of elasticity (N/mm2)

Limiting the Stress to 35 N/mm2 and the deflection to 12.7mm the maximum pipe span
for continuous piping is calculated from the lesser of the following formulae: -

240 Iσ 384 EIδ


L= L=4
wD 100000 w
Notes: -
1- Pipes are assumed to be full of water s.g. = 1.0
2- Insulation density is assumed to be 150 kg/m3
3- Insulation thickness is based upon Spec No 60-0000-L-0010 Rev D (Temp 201 - 250ºC)

Pagee 6 of 22
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
PROJECT №. 571500
SPECIFICATION FOR PIPE SUPPORTS DOC №. : 60-0000-L-SPE-0002
Rev. 4

4- The maximum spans for piping arrangements other than continuous spans are shown
below.

Max Span = 0.8 x L

Max Span = 0.75 x L

Max Span = 0.65 x L

Pagee 7 of 22
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
PROJECT №. 571500
SPECIFICATION FOR PIPE SUPPORTS DOC №. : 60-0000-L-SPE-0002
Rev. 4

PIPE SPAN TABLES FOR CONTINUOUS PIPE SPANS

Pipes Full (SG=1), Insulated (Temp 250oC)


Pipe Schedule
Size 10 20 30 STD 40 XS 80 120 160
¾ 2.6 2.6 2.3 2.3 3.6
1 3.3 3.3 3.6 3.6 4.2
1½ 4.0 4.0 4.5 4.5 5.1
2 4.4 4.4 5.1 5.1 5.9
3 5.9 5.9 7.0 7.0 7.5
4 7.0 7.0 8.0 8.0 8.5
6 8.5 8.5 10.0 10.0 10.5
8 9.0 9.4 10.0 10.0 11.5 11.5 12.3
10 9.6 10.5 11.2 11.2 12.4 13.0 13.9
12 9.9 11.2 11.7 12.2 13.0 14.2 15.2
14 10.1 11.2 12.1 12.0 12.8 13.4 14.9 16.0
16 10.3 10.9 12.5 12.2 13.9 13.9 16.0 17.1
18 10.4 10.9 13.5 12.3 14.8 14.2 17.0 18.2
20 10.6 12.5 14.6 12.5 15.5 14.6 18.0 19.2
22 10.8 12.7 14.9 12.7 16.2 14.9 18.9 20.2
24 11.0 12.9 15.9 12.9 17.1 15.1 19.9 21.2

Pipes Full (SG=1), Not Insulated


Pipe Schedule
Size 10 20 30 STD 40 XS 80 120 160
¾ 3.3 3.3 3.9 3.9 4.2
1 4.0 4.0 4.5 4.5 4.8
1½ 4.8 4.8 5.4 5.4 5.8
2 5.3 5.3 6.1 6.1 6.6
3 7.0 7.0 7.7 7.7 8.2
4 7.9 7.9 8.7 8.7 9.1
6 9.4 9.4 10.6 10.6 11.1
8 9.6 10.1 10.6 10.6 12.0 12.0 12.8
10 10.1 11.0 11.8 11.8 12.9 13.5 14.3
12 10.5 11.8 12.4 12.8 13.6 14.7 15.7
14 10.6 11.8 12.7 12.7 13.4 14.0 15.5 16.4
16 10.9 11.6 13.1 12.9 14.5 14.5 16.6 17.6
18 11.1 11.7 14.2 13.1 15.5 14.9 17.6 18.7
20 11.3 13.3 15.3 13.3 16.2 15.3 18.6 19.7
22 11.4 13.4 15.6 13.4 16.8 15.6 19.5 20.7
24 11.5 13.5 16.6 13.5 17.7 15.8 20.4 21.7

Pagee 8 of 22
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
PROJECT №. 571500
SPECIFICATION FOR PIPE SUPPORTS DOC №. : 60-0000-L-SPE-0002
Rev. 4

PIPE SPAN TABLES FOR CONTINUOUS PIPE SPANS

Pipes Empty, Insulated (Temp 250oC)


Pipe Schedule
Size 10 20 30 STD 40 XS 80 120 160
¾ 2.7 2.7 2.5 2.5 3.6
1 3.5 3.5 3.9 3.9 4.3
1½ 4.4 4.4 5.0 5.0 5.4
2 4.9 4.9 5.6 5.6 6.2
3 7.1 7.1 7.7 7.7 8.0
4 8.4 8.4 9.1 9.1 9.4
6 10.7 10.7 11.5 11.5 11.8
8 12.0 12.3 12.7 12.7 13.5 13.5 13.8
10 13.5 14.2 14.7 14.7 15.3 15.5 15.7
12 14.6 15.6 15.9 16.1 16.6 17.0 17.3
14 15.3 16.2 16.8 16.8 17.2 17.4 18.0 18.2
16 16.2 17.1 17.8 17.8 18.6 18.6 19.4 19.5
18 16.7 17.7 19.0 18.5 19.7 19.4 20.5 20.7
20 17.6 19.5 20.5 19.5 21.0 20.5 21.8 22.0
22 18.5 20.6 21.6 20.6 22.2 21.6 23.1 23.2
24 19.4 21.5 23.0 21.5 23.5 22.6 24.2 24.3

Pipes Empty, Not Insulated


Pipe Schedule
Size 10 20 30 STD 40 XS 80 120 160
¾ 3.6 3.6 4.1 4.1 4.4
1 4.4 4.4 4.8 4.8 5.0
1½ 5.5 5.5 6.0 6.0 6.2
2 6.3 6.3 6.8 6.8 7.0
3 8.3 8.3 8.7 8.7 8.8
4 9.7 9.7 10.0 10.0 10.1
6 12.1 12.1 12.5 12.5 12.6
8 13.6 13.8 14.1 14.1 14.5 14.5 14.5
10 15.3 15.7 16.0 16.0 16.3 16.4 16.4
12 16.6 17.3 17.5 17.6 17.8 18.0 17.9
14 17.5 18.0 18.4 18.4 18.6 18.7 18.9 18.9
16 18.7 19.3 19.7 19.7 20.1 20.1 20.4 20.2
18 19.8 20.5 21.2 20.9 21.5 21.3 21.7 21.5
20 20.9 22.1 22.5 22.1 22.7 22.5 22.9 22.7
22 21.9 23.2 23.7 23.2 23.9 23.7 24.1 23.9
24 22.9 24.2 24.9 24.2 25.1 24.8 25.2 25.0

Pagee 9 of 22
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
PROJECT №. 571500
SPECIFICATION FOR PIPE SUPPORTS DOC №. : 60-0000-L-SPE-0002
Rev. 4

7. MAXIMUM GUIDE SPACING


Pipe Maximum Span between guides (m)
Size Horizontal Pipes Vertical Pipes
¾ 8.0 7.0
1 8.0 7.0
1½ 8.0 7.0
2 8.0 7.0
3 16.0 8.0
4 16.0 8.0
6 16.0 10.0
8 24.0 12.0
10 24.0 12.0
12 24.0 14.0
14 24.0 14.0
16 24.0 16.0
18 24.0 16.0
20 32.0 18.0
22 32.0 18.0
24 32.0 18.0

Pagee 10 of 22
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
PROJECT №. 571500
SPECIFICATION FOR PIPE SUPPORTS DOC №. : 60-0000-L-SPE-0002
Rev. 4

8. PIPE SHOE HEIGHTS


Non-insulated and personnel protection insulated pipes shall rest directly upon the support
steelwork. Pipes with heat or cold conservation insulation shall be supported on shoes.
The shoe height is determined from the tables below: -

HEAT CONSERVATION THICKNESS TABLE

(Ref Doc No60-0000-L-SPE-0010 Section 5.17.1)

INSULATION THICKNESS FOR OPERATING TEMPS


PIPE SIZE
(Deg.C.)
AMB to 101 to 151 to 201 to 251 to
DN NPS 51 to 100
50 150 200 250 350
15 ½ 40 40 40 40 40 50
20 ¾ 40 40 40 40 40 50
25 1 40 40 40 40 40 50
40 1½ 40 40 40 40 50 60
50 2 40 40 40 40 60 80
80 3 40 40 50 60 60 80
100 4 40 40 60 60 60 80
150 6 40 50 60 60 70 90
200 8 50 50 60 60 70 90
250 10 50 50 70 70 70 90
300 12 60 60 70 80 80 100
350 14 60 60 70 80 80 100
400 16 60 60 70 90 90 110
450 18 60 70 70 90 110 110
500 20 60 70 90 100 110 120
600 24 70 70 90 100 110 120
600 - 1000 24 - 40 70 70 90 100 110 120
≥ 1050 ≥ 42 70 70 90 100 110 120

Notes: -

• The pipe shoe height in the non-shaded area of the above table shall be 100mm

• The pipe shoe height in the shaded area of the above table shalll be 150mm

• The intermediate beam of the main SGP piperack is set 50 mm lower than the main beams.
Pipe Sizes 2", 3" & 4" only will be supported on this beam, therefore shoe heights will be
150mm for insulated lines and 50mm for non-insulated lines.

Pagee 11 of 22
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
PROJECT №. 571500
SPECIFICATION FOR PIPE SUPPORTS DOC №. : 60-0000-L-SPE-0002
Rev. 4

COLD CONSERVATION OR PERSONNEL PROTECTION COLD TABLE

Ref Doc No 60-0000-L-SPE-0010 Section 6.12 & 6.13


PIPE SIZE INSULATION THICKNESS
DN PERSONNEL
NPS PROTECTION COLD COLD CONSERVATION (CI)
(PPC)
20 ¾ 30 40 50 60
25 1 30 40 60 60
40 1½ 30 40 50 60 70
50 2 30 40 50 60 70
80 3 30 40 50 60 70 80
100 4 30 40 50 60 70 80
150 6 30 40 50 60 80 90
200 8 30 40 50 70 80 100
250 10 30 40 50 70 80 100
300 12 30 40 50 60 70 90 100
350 14 30 40 50 60 70 90 100
400 16 30 40 50 60 70 90 100
450 18 30 40 50 60 70 90 110
500 20 30 40 50 60 70 90 110
600 24 30 40 50 60 70 90 110
650 26 30 40 50 60 70 90 110
700 28 30 40 50 60 70 90 110
750 30 30 40 50 60 70 90 110
800 32 30 40 50 60 70 90 110
850 34 30 40 50 60 80 100 110
900 36 30 40 50 60 80 100 110
>900 >36 30 40 50 60 80 100 120

100 150 200


High High High
Shoe Shoe Shoe

Notes: -

• The pipe shoe height in the non-shaded area of the above table shall be 100mm

• The pipe shoe height in the lightly shaded area of the above table shalll be 150mm

• The pipe shoe height in the heavy shaded area of the above table shalll be 200mm

The intermediate beam of the main SGP piperack is set 50 mm lower than the main beams. Pipe
Sizes 2", 3" & 4" only will be supported on this beam, therefore shoe heights will be 50mm greater
than indicated above.

Pagee 12 of 22
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
PROJECT №. 571500
SPECIFICATION FOR PIPE SUPPORTS DOC №. : 60-0000-L-SPE-0002
Rev. 4

9. ALLOWABLE LOADS FOR NON-INSULATED PIPES, PIPE SHOES, PIPE ANCHORS


& TRUNNIONS
The allowable loads for pipe shoes, pipe anchors and trunnions are listed in the pipe
support attachments. The allowable loads for non-insulated pipes with a design
temperature up to 50°C are shown below: -

Allowable loads for Non-Insulated pipes resting on support steel

Max Allowable Load (KN)


Pipe Size Pipes without a re-pad Pipes with a re-pad
(") Carbon Steel Stain. Carbon Stain.
Steel Steel Steel
c.a. = 1.5 c.a. = 3.0
c.a. = 1.0 All pipes c.a. = 1.0
2 8.0 6.0 10.0 25.0 25.0
3-4 12.0 5.0 15.0 40.0 40.0
6-8 15.0 9.0 12.0 45.0 50.0
10 - 12 20.0 14.0 10.0 50.0 55.0
14 - 18 12.0 7.0 9.0 40.0 30.0
20 - 24 15.0 10.0 8.0 40.0 27.0
26 - 40 32.0 32.0

For lines that have higher design temperatures the tabulated loads shall be multiplied by
the temperature correction factor shown below: -

Temperature Correction Factor


Material Carbon Steel Stain. Steel
Grade A333 Gr 8 A671 CC 60 A312 TP316/L
Pipe Size 2" - 16" 18" - 36" 2" - 36"
50 1.00 1.00 1.00
Temperature °C

100 1.00 0.97 1.00


150 1.00 0.94 1.00
200 1.00 0.92 0.96
250 0.95 0.88 0.91
300 0.89 0.81 0.86
350 0.83 0.76 0.83
400 0.65 0.65 0.81

Unless noted otherwise, the maximum loads for non-insulated pipes, pipe shoes, pipe
anchors and trunnions are based upon pipes with a 12.5% tolerance, a corrosion
allowance of 3.0mm and pipe schedules of: -
2” Sch XS
3” – 12” Sch 40
14” – 36” Sch 20
40” Sch Std

Note- these pipe schedules represent the smallest wall thickness in the piping
specification.

For pipes without re-pads, the following equation can be used to increase the actual
allowable load: -

Pagee 13 of 22
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
PROJECT №. 571500
SPECIFICATION FOR PIPE SUPPORTS DOC №. : 60-0000-L-SPE-0002
Rev. 4

1 .5
tp
Allowable load = tabulated load * 1 .5
* temp correction factor
tt
Where: - tp is the pipe thickness (less c.a. and tolerances) of the pipe in question
tt is the pipe thickness (less c.a. and tolerances) of the pipe used to calculate the
tables

Example

What is the maximum load that can be applied to an non-insulated 18” Sch 40 pipe
corrosion allowance = 3.0mm, design temp = 150°C with out a re-pad.

18” Sch 40 pipe tp = (14.27 x 0.875) – 3 = 9.49mm


18” Sch 20 pipe tt = (7.92 x 0.875) – 3 = 3.93mm

9 . 49 1 .5
Allowable load = 10 * * 0 . 94 = 35 . 3 KN
3 . 93 1 .5

10. PROCEDURE FOR INSTALLATION OF ANCHOR BOLTS AND GROUTING OF BASE


PLATES

The procedure for the installation of Anchor bolts and grouting of Base plates is included in
the following Guidelines that are issued into ProArc: -

60-0000-S-RLY-0006-01 SGP roads and paving layout settlement monitoring


guidelines
60-0000-S-RLY-0006-02 SGP roads and paving layout 0200 Area settlement
monitoring guidelines
60-0000-S-RLY-0006-03 SGP roads and paving layout 0400 Area settlement
monitoring guidelines
60-0000-S-RLY-0006-04 SGP roads and paving layout 0700 Area settlement
monitoring guidelines

Pagee 14 of 22
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
PROJECT №. 571500
SPECIFICATION FOR PIPE SUPPORTS DOC №. : 60-0000-L-SPE-0002
Rev. 4

ATTACHMENT A SHOES
SUPPORT TYPE SUPPORT NO SHEET NO REV
Standard Length Welded Shoe S1, S5, S9 A1, A2, A3 2
Long Welded Shoe S2, S6, S10 A4, A5 2
Long Welded Shoe S2, S6 A6, A7 4
Standard Clamped Shoe, pipe sizes ½”- 6” S3, S7, S11 A8 3
Standard Clamped Shoe, pipe sizes 8”- 24” S3, S7, S11 A9 2
Long Clamped Shoe S4, S8, S12 A10, A11 2
PTFE for Pipe Shoes S19 A12, A13 2
Standard Clamped Shoe for Stainless Steel Pipes S103, S107,
A14 2
Sizes ½”- 6” S111
Standard Clamped Shoe for Stainless Steel Pipes S103, S107,
A15 3
Sizes 8”- 32” S111
Long Clamped Shoe for Stainless Steel Pipes, pipe S104, S108,
A16 2
sizes ½”- 6” S112
Long Clamped Shoe for Stainless Steel Pipes, pipe S104, S108,
A17 3
sizes 8”- 24” S112
Isolator Pad for Stainless Steel Pipes S113 A18 3
Pick-Up Support for 3” and below Insulated Pipes S114 A19 2
Pick-Up Support for 3” and below Uninsulated Pipes S115 A20 2
Packing Plates for gaps up to 20mm PK1 A21, A22 3
Packing Support for gaps 21 to 60mm for pipes with
PK2 A23 2
guides
Packing Support for gaps 21 to 60mm without
PK3 A24 3
guides. Pipe sizes 42” and below
Packing Support for gaps 61 to 80mm PK4, PK5 A25, A26 2
PTFE for Long Pipe Shoes S20 A27, A28 2
Pipe Shoe for SECT Traced piping S21 A29 0
Long welded shoes for Pipe Specs 150H26 &
S13, S14 A30, A31 0
150K26. Pipe sizes 36” – 40”
Packing Support for gaps 21 to 60mm for 44” to 92”
PK3 A32 1
pipes
Stiffening Rings SR1, SR101 A33 0
Double Pipe Shoe for SECT Traced piping S22 A34 0
Puddle Flanges for Sump Covers PF1, PF101 A35 0
Shoe for Contra-Traced Piping S15 A36 0

ATTACHMENT B ANCHORS, GUIDES & VERTICAL PIPE SUPPORTS


SUPPORT TYPE SUPPORT NO SHEET NO REV
Directional Anchor for Bare pipes DA1 B1, B2, B3 2
Directional Anchor for Insulated pipes sizes ½”- 4” DA2, DA3 B4 4
Directional Anchor for Insulated pipes sizes 6”- 24” DA2, DA3 B4, B5, 3
Directional Anchor for Insulated pipes sizes 26”- 92” DA2, DA3 B6, 4
Directional Anchor for Insulated pipes sizes 26”- 92”
DA2, DA3 B7 5
Dimensions
Guides for Insulated Horizontal pipes HG1 B8 2
Guides for Bare Horizontal pipes HG2 B9, B10 2
Hold-down Guide HG3 B11 2
Guide for Bare Pipes 2” and smaller (1 Pipe) VG1 B12 2

Pagee 15 of 22
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
PROJECT №. 571500
SPECIFICATION FOR PIPE SUPPORTS DOC №. : 60-0000-L-SPE-0002
Rev. 4

Guide for Pipes 2” and smaller (2 or more Pipes) VG2 B13 2


Guide for 3”- 6” Bare Pipes and ½”- 6” Insulated
VG3 B14 2
Pipes
4-Way Guide for 8”- 24” Bare Pipes VG4 B15, B16 2
4-Way Guide for 8”- 24” Insulated Pipes VG5, VG6 B15, B16 2
2-Way Guide for 4”- 24” Bare Pipes VG7, VG8 B17, B18 2
2-Way Guide for 4”- 24” Insulated Pipes VG9, VG10 B17, B18 2
Vertical Pipe Support, Cantilever VS1 B19 2
Vertical Pipe Support, Braced Cantilever VS2 B20 2
Vertical Pipe Support and Guide, Horizontal Frame VS3 B21 2
Vertical Pipe Support, Braced Horizontal Frame VS4 B22 2
Vertical Pipe Support from Vessels for pipe sizes 2”-
VS5 B23 2
10”
Vertical Pipe Support from Vessels for pipe sizes 4”-
VS6 B24, B25 2
24”
Rigid Strut with Trunnion and Clamp RS1 B26 2
Rigid Strut with Shoe RS2 B27 2
Line stop for non-insulated Stainless Steel lines
DA101 B28 2
<=1½”
Line stop for insulated Stainless Steel lines <=1½” DA102 B29 2
Line stop for non-insulated Galvanised lines <=3” DA201 B30 2
Line stop for insulated Galvanised lines <=3” DA202 B31 2

Vertical Guide for Non-insulated Stainless Steel VG104,


B32, B33 2
Pipes 4”-24” VG107, VG108

Directional Anchor for Non-Insulated pipes on B34, B35


DA4 0
sleepers ≤ 600mm B36
Directional Anchor for Insulated pipes on sleepers ≤
DA5, DA6 B37,B38 0
600mm Pipe sizes ½” – 24”
Directional Anchor for Non-Insulated pipes on B39,B40,
DA7 0
sleepers > 600mm B41
Directional Anchor for SECT Traced piping on
DA8 B42 0
steelwork
Directional Anchor for SECT Traced piping on
DA9 B43 0
sleepers
Directional Anchor for Insulated pipes on sleepers >
DA10 B44, B45 0
600mm
Directional Anchor for Pipe Specs 150H26 &
DA11, DA12 B46, B47 0
150K26. Pipe sizes 36” – 40”
Directional Anchor for Insulated pipes on sleepers ≤
DA5, DA6 B48, B49 0
600mm Pipe sizes 24” – 40”
B50, B51,
Directional Anchor for Acoustically Insulated pipes DA13 0
B52, B53
Directional Anchor for Non-Insulated piping with a
DA103 B54,B55 0
design temp of -60°C or below
Anchor Shoe for SECT Traced piping on steelwork SAS1 B56 0
Anchor Shoe for SECT Traced piping on sleepers SAS2 B57 0

ATTACHMENT C TRUNNIONS & BASE SUPPORTS


SUPPORT TYPE SUPPORT NO SHEET NO REV
One Horizontal Trunnion from a Straight Pipe T1 C1 3

Pagee 16 of 22
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
PROJECT №. 571500
SPECIFICATION FOR PIPE SUPPORTS DOC №. : 60-0000-L-SPE-0002
Rev. 4

Horizontal Trunnion Allowable Loads T1 C3 2


Two Horizontal Trunnions from a Straight Pipe T2 C2, C3 2
Horizontal Trunnion from an Elbow T3 C4 2
Non-Adjustable Base Supports BS1 C5 4
Adjustable Base Supports BS2 C6, C7 2
PTFE for Base Supports BS3 C8, C9 2
Base Anchor for Non-Adjustable Support BA1 C10 2
Base Anchor for Adjustable Support BA2 C11 2
Base Guide for Non-Adjustable Support BG1 C12 3
Base Guide for Adjustable Support BG2 C13 3
Base Plate from grade BP C14 3
Non-Adjustable Base Support from grade in non-
BS4 C15 4
paved areas
Base Plate from steelwork BPS C16 2
Allowable loads for horizontal trunnions from elbows T3 C17 2
Non Adjustable Base Support from a Civil Designed
BS5 C18 4
Foundation
Small Non-adjustable Base Support from existing
BS6 C19 4
steel
Two Horizontal Trunnions from a Straight Pipe for
T2 C20 0
pipe sizes 48” and larger

ATTACHMENT D HANGERS & SPRINGS


SUPPORT TYPE SUPPORT NO SHEET NO REV
Hanger with 2-Bolt Clamp for Bare Pipes (Light
HR1 D1, D2 2
Load)
Hanger with 2-Bolt Clamp for Bare Pipes (Heavy
HR2 D1, D2 2
Load)
Hanger with Lug for Bare Pipes (Light Load) HR3 D1, D2 2
Hanger with 3-Bolt Clamp for Insulated Pipes (Light
HR4 D3, D4 2
Load)
Hanger with 3-Bolt Clamp for Insulated Pipes (Heavy
HR5 D3, D4 2
Load)
Hanger with 2-Bolt Clamp for Bare Pipes (Light
HR6 D5, D6 2
Load)
Hanger with 2-Bolt Clamp for Bare Pipes (Heavy
HR7 D5, D6 2
Load)
Hanger with Lug for Bare Pipes (Light Load) HR8 D5, D6 2
Hanger with 3-Bolt Clamp for Insulated Pipes (Light
HR9 D7, D8 2
Load)
Hanger with 3-Bolt Clamp for Insulated Pipes (Heavy
HR10 D7, D8 2
Load)
Hanger with 2-Bolt Clamp for Bare Stainless Steel
HR101 D9, D10 2
Pipes (Light Load)
Hanger with 2-Bolt Clamp for Bare Stainless Steel
HR102 D9, D10 2
Pipes (Heavy Load)
Hanger with 3-Bolt Clamp for Insulated Stainless
HR104 D11, D12 2
Steel Pipes (Light Load)
Hanger with 3-Bolt Clamp for Insulated Stainless
HR105 D11, D12 2
Steel Pipes (Heavy Load)
Hanger with 2-Bolt Clamp for Bare Stainless Steel
HR106 D13, D14 2
Pipes (Light Load)

Pagee 17 of 22
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
PROJECT №. 571500
SPECIFICATION FOR PIPE SUPPORTS DOC №. : 60-0000-L-SPE-0002
Rev. 4

Hanger with 2-Bolt Clamp for Bare Stainless Steel


HR107 D13, D14 2
Pipes (Heavy Load)
Hanger with 3-Bolt Clamp for Insulated Stainless
HR109 D15, D16 2
Steel Pipes (Light Load)
Hanger with 3-Bolt Clamp for Insulated Stainless
HR110 D15, D16 2
Steel Pipes (Heavy Load)
Trapeze Hangers TH D17 2

Spring Hanger from underside of steel for Bare Pipes SH1 D18 2

Spring Hanger from underside of steel for Insulated


SH2 D18 2
Pipes
Spring Hanger from top of steel for Bare Pipes SH3 D19 2
Spring Hanger from top of steel for Insulated Pipes SH4 D19 2
Trapeze Spring Hanger from underside of steel SH5 D20 2
Trapeze Spring Hanger from top of steel SH6 D21 2
Trapeze Spring Hanger from underside of steel
SH7 D22 2
(Springs Underneath Pipe)
Pedestal Spring SH8 D23 2
Constant Spring Hanger from underside of steel for
SH11, SH12 D24 2
All Pipes
Constant Spring Hanger from top of steel for All
SH13, SH14 D25 2
Pipes
Trapeze Constant Spring Hanger from underside of
SH15, SH16 D26 2
steel
Trapeze Constant Spring Hanger from top of steel SH17, SH18 D27 2
Pedestal Constant Springs SH19, SH20 D28 2
Spring Hangers from Top of Steel to Elbow Hanger SH9 D29 2
Spring Hangers for Cold Insulated Pipes SH21, SH22 D30 0
Spring Hangers from Underside of Steel to Pipe
SH10 D31 0
Elbow
Spring Hangers from Underside of Steel to Pipe Lug SH23 D32 0
Spring Hangers from Top of Steel to Pipe Lug SH24 D33 0
Horizontal Pipe Support - Single Bank PS15 D34 0

ATTACHMENT E STRUCTURAL SUPPORTS


SUPPORT TYPE SUPPORT NO SHEET NO REV
T-Post from structure P1 E1 2
Post with Square Plate from structure P2 E2 2
Cantilevered Post from structure P3 E3 2
Goal Post from structure P4 E4, E5 2
Post from structure P5 E6 2
Welded Cantilevered Post from structure P6 E7 2
Inverted T-Post P7 E8 3
Inverted Cantilevered Post P8 E9 2
Inverted Goal Post P9 E10, E11 2
Inverted Welded Cantilevered Post P10 E12 3
Inverted Goal Post (For PipeRacks only) P11 E13 2
P21, P22, P23, E14, E15,
Simple Cantilevers 2
P24, P25 E16
P26, P27, P28, E17, E18,
Braced Cantilevers 2
P29, P30 E19
Beams Welded to Columns P31, P32, P33 E20, E21 2

Pagee 18 of 22
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
PROJECT №. 571500
SPECIFICATION FOR PIPE SUPPORTS DOC №. : 60-0000-L-SPE-0002
Rev. 4

Beams Welded to Beams P34, P35, P36 E22, E23 2


Cantilevered Beams P37, P38, P39 E24, E25 2
T-Post from new paving P41 E26 3
Post with Square Plate from new paving P42 E27 2
Cantilevered Post from new paving P43 E28 3
Goal Post from new paving, pipe sizes ½” – 2” P44 E29 3
Goal Post from new paving, pipe sizes ≥ 3” P44 E30 2
Post from new paving P45 E31 2
Welded Cantilevered Post from new paving P46 E32 2
T-Post for un-paved areas P51 E33 2
Post with Square Plate for un-paved areas P52 E34 2
Cantilevered Post for un-paved areas P53 E35 2
Goal Post for un-paved areas, pipe sizes ½” – 2” P54 E36, 2
Goal Post for un-paved areas, pipe sizes ≥ 3” P54 E37 3
Post for un-paved areas P55 E38 3
Welded Cantilevered Post for un-paved areas P56 E39 3
T-Post from structure or grade for Utility stations P60 E40 3
Support for utility stations from platforms P61 E41 2
Cantilever Support for utility stations P62 E42 2
Support for Steam Trap Manifolds P63 E43 2
Base Plate for Cantilever to Concrete P20 E44 3
T-Post for un-paved areas P71 E45 3
Post with Square Plate for un-paved areas P72 E46 3
Cantilevered-Post for un-paved areas P73 E47 3
Goal Post for un-paved areas P74 E48 3
Post for un-paved areas P75 E49 3
Welded Cantilevered Post for un-paved areas P76 E50 3
T-Post for use in Caustic Sump P64 E51 0

ATTACHMENT F SMALL BORE & ANCILLARY SUPPORTS


SUPPORT TYPE SUPPORT NO SHEET NO REV
Base Support and Guide from Steel for horizontal
SB1, SB2 F1 2
pipes
Base Support and Guide from Grade for horizontal
SB3, SB4 F2 4
pipes
Base Support from Steel for vertical pipes SB5 F3 2
Base Support from Grade for vertical pipes SB6 F4 4
Support and Guide from adjacent Steel for vertical
SB7 F5 2
pipes
Support from adjacent Steel for vertical pipes SB8 F6 2
Guide for vertical pipes SB9 F7 2
Base Support and Guide from Steel for horizontal
SB101, SB102 F8 2
Stainless Steel pipes
Base Support and Guide from Grade for horizontal
SB103, SB104 F9 4
Stainless Steel pipes
Base Support from Steel for vertical Stainless Steel
SB105 F10 2
pipes
Base Support from Grade for vertical Stainless Steel
SB106 F11 4
pipes
Support and Guide from adjacent Steel for vertical
SB107 F12 3
Stainless Steel pipes
Support from adjacent Steel for vertical Stainless SB108 F13 3

Pagee 19 of 22
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
PROJECT №. 571500
SPECIFICATION FOR PIPE SUPPORTS DOC №. : 60-0000-L-SPE-0002
Rev. 4

Steel pipes
Guide for vertical Stainless Steel pipes SB109 F14 2
2-Bolt Pipe Clip, Light Load PC1 F15, 2
2-Bolt Pipe Clip, Heavy Load PC2 F15, 2
2-Bolt Pipe Clip, Dimensions PC1, PC2 F16 3
3-Bolt Pipe Clip, Light Load PC3 F17, F18 2
3-Bolt Pipe Clip, Heavy Load PC4 F17, F19 2
2-Bolt Pipe Clip, Light Load for Stainless Steel pipes PC101 F20, F21 3
2-Bolt Pipe Clip, Heavy Load for Stainless Steel
PC102 F20, F21 3
pipes
3-Bolt Pipe Clip, Light Load for Stainless Steel pipes PC103 F22, F23 2
3-Bolt Pipe Clip, Heavy Load for Stainless Steel
PC104 F22, F24 2
pipes
U-Bolt Guide UG F25 2
U-Bolt Anchor UA F26 2
Clevis CLL, CLR F27 2
Turnbuckle TB F28 2
Weldless Eye Nut WENL, WENR F29 2
Threaded Rod RA, RB, RC F30 2
Lug L F31 2
C1, C2, C3,
Cradle for Shoes and Anchors C101, C102, F32, F33 4
C103
C4, C5, C6,
Full Encirclement pad C104, C105, F34, F35 2
C106
Insulated U-Bolt Anchor for Stainless Steel Pipes UA101 F36 3
Insulated U-Bolt Guide for Stainless Steel Pipes UA102 F37 3
Lifting Lugs for Piping Break-Out Spools from an
LL1 F38 4
elbow
Lifting Lugs for Piping Break-Out Spools from pipe LL2 F39 4
GSW1,
GSW101,
Gusset Supports F40, F41 1
GSB1,
GSB101
C7, C8, C107,
Cradle for Anchors on Concrete sleepers F42 0
C108
Lifting Lugs for Piping Break-Out Spools from an
LL1 F43 0
elbow, Large Bore Piping
Lifting Lugs for Piping Break-Out Spools from
LL102 F44 0
Stainless Steel pipe
U-Bolt Guide for pipes in the Caustic Sump UG301 F45 0
U-Bolt Anchor for pipes in the Caustic Sump UB301 F46 0
Base Guide/Anchor Pipes in Caustic Sump SB301, SB302 F47 0
Base Guide for 2 pipes in Caustic Sump SB303 F48 0
Gusset Support for SP Item Nos. SP-1914 &
GSW2 F49 0
SP-1916

ATTACHMENT G PIPE SUPPORT FOUNDATIONS


SUPPORT TYPE SUPPORT NO SHEET NO REV
Pipe Support Foundation for New Paving F8N-1 G1 3
Pipe Support Foundation for New Paving F8N-2 G2 3

Pagee 20 of 22
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
PROJECT №. 571500
SPECIFICATION FOR PIPE SUPPORTS DOC №. : 60-0000-L-SPE-0002
Rev. 4

Pipe Support Foundation Loading Graph F8N-1, F8N-2 G3 2


Augered Pile, Pipe Support Foundation for welded
F9-1 G4, G5 3
Posts in non-paved areas (Light loads)
Augered Pile, Pipe Support Foundation for welded
F9-2, G6, G7 3
Posts in non-paved areas (Heavy loads)
Augered Pile, Pipe Support Foundation for trunnion
F9-4 G8, G9 3
or Base supports in non-paved areas (Light loads)
Augered Pile, Pipe Support Foundation for trunnion
F9-5 G10, G11 2
or Base supports in non-paved areas (Heavy loads)
Pipe Support Baseplate on a Civil Foundation or
F8N3 G12 4
Pipe Support foundation F9-6,F9-7 & F9-8
Pipe Support Baseplate on a Civil Foundation or
F8N4 G13 3
Pipe Support foundation F9-6,F9-9 & F9-10
Pipe Support foundation for non paved areas for 2" &
F9-6 G14 2
3" trunnions and welded posts HEA 100
Pipe Support foundation for non paved areas for 4" &
F9-7 G15 2
6" trunnions
Pipe Support foundation for non paved areas for 8",
F9-8 G16 2
10”& 12" trunnions
Pipe Support foundation for non paved areas for
F9-9 G17 2
welded posts HEA 160 & HEA 200
Pipe Support foundation for non paved areas for
F9-10 G18 2
Small Bore Pipe Supports and 70 x 8 Angle Posts

ATTACHMENT H COLD SUPPORTS & ANTI VIBRATION SUPPORTS


SUPPORT TYPE SUPPORT NO SHEET NO REV
Cold Shoe, Standard Length CS1 H1 2
Cold Shoe, Long CS2 H2 2
Cold Double Shoe, Standard Length CS3 H3 2
Anchor Shoe CAS1 H4 2
Directional Anchor CDA1 H5 2
Non-Adjustable Hanger CH1 H6, H7 2
Base Support CBS1 H8 2
Trunnion Support CTS1 H9 3
CVG1, CVG2,
4-Directional Vertical Guide H10, H11 2
CVG3
CVG4, CVG5,
2-Directional Vertical Guide H12, H13 2
CVG6
H14, H15,
Hold Down Support for Non-Insulated Piping HD1 2
H16
Hold Down Guide for Non-Insulated Piping HD2 H17, H18 2
Hold Down Support for Insulated Piping HD3 H19, H20 2
Slotted Hold Down Support for Non-Insulated Piping HDS1 H21, H22 2
Slotted Hold Down Support for Non-Insulated Piping HDS2 H23, H24 3
Anchor strap AS1 H25, H26 0

ATTACHMENT J SELECTION SHEETS


Shoes, PTFE Supports Pick-Up Supports & Packing Supports J1A 2
Shoes, PTFE Supports Pick-Up Supports & Packing Supports J1B 0
Guides, Line Stops & Rigid Struts J2 2

Pagee 21 of 22
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
PROJECT №. 571500
SPECIFICATION FOR PIPE SUPPORTS DOC №. : 60-0000-L-SPE-0002
Rev. 4

Vertical Supports & Guides and SS & Galvanised Steel Line Stops J3A 2
Vertical Supports & Guides and SS & Galvanised Steel Line Stops J3B 0
Base Supports & Trunnions J4 2
Hangers J5 1
Spring Hangers J6A 2
HVAC Piping J6B 0
Posts, Cantilevers, Brackets & Beams welded to Structural Steel J7, J8 1
Posts, Cantilevered Posts & Utility Supports from Grade J9, J10 1
Small Bore Supports, Lugs & Cradles J11A 2
Small Bore Supports, Lugs & Gussets J11B 0
Pipe Support Foundations J12 1
Cold Supports & Anti-vibration Supports J13 1

Pagee 22 of 22
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Beam shall be cut


longitudinally to form shoe.

1
= =
300 100

Fabrication
Orientation Angle
N

NOTE - Where shoes are located on vertical


pipes (e.g. Support Nos VG1 - VG10) the
orientation of the shoe shall be added to the
"Fabrication Orientation" field of the PDS form.

Support Pipe Size Dimension Mark No 1 M.T.O. Max Vertical


Type H Length Load (KN)
S1 ½" - 6" 100 IPE 200 150
S5 ½" - 6" 150 IPE 200 300 40.0
S9 ½" - 6" 50 IPE 200 150

Assembly Tag No: - S1 or S5 or S9 - X


Detail No Pipe Size
SUPPORT No S1, S5, S9
SUPPORT TYPE Welded Shoe, Standard Length Sheet A1
PIPE SIZE ½" - 6"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Cradle if required
refer to Support C1

H B

1
20 2 30
(typ) (typ)
= =
A
300
Support No S1
Pipe Mark No 1 M.T.O. M.T.O. Mark No 2 M.T.O. Dimension
Size Length Area (cm²) Area (cm²) A B H
8,10 300 x 10 290 364 200
12,14 Thk 340 10 Thk 504 250 10
16,18 Plate 390 Plate 644 300 100
20,22 12 Thk 1320 784 350 12
24 Plate 1470 924 400
Support No S5
Pipe Mark No 1 M.T.O. M.T.O. Mark No 2 M.T.O. Dimension
Size Length Area (cm²) Area (cm²) A B H
8,10 300 x 10 340 494 200
12,14 Thk 390 10 Thk 684 250 10
16,18 Plate 440 Plate 874 300 150
20,22 12 Thk 1470 1064 350 12
24 Plate 1620 1254 400
Support No S9
Pipe Mark No 1 M.T.O. M.T.O. Mark No 2 M.T.O. Dimension
Size Length Area (cm²) Area (cm²) A B H
8,10 300 x 10 240 234 200
12,14 Thk 290 10 Thk 324 250 10
16,18 Plate 340 Plate 414 300 50
20,22 12 Thk 1170 504 350 12
24 Plate 1320 594 400
NOTE - Where shoes are located on Max Vertical Load (KN)
vertical pipes (e.g. Support Nos Pipe Size Bare pipes Pipes with a re-pad
VG1 - VG10) the orientation of the shoe (") c.a. = 1.5 c.a. = 3.0 All Pipe Schedules
shall be added to the "Fabrication 8 - 18 90.0 55.0 200.0
Orientation" field of the PDS form. 20 - 24 130.0 90.0 200.0
Refer to Sheet A1 for details.
Assembly Tag No: - S1 or S5 or S9 - X
Detail No Pipe Size
SUPPORT No S1, S5, S9
SUPPORT TYPE Welded Shoe, Standard Length Sheet A2
PIPE SIZE 8" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

24º
30º
3
10 H 2

Cradle is
Mandatory 12
30 10
Ref Sup't (typ) (typ)
= =
No C1
= =
300 50 A
(typ)

Support No S1
Pipe Mark No 1 M.T.O. Mark No 2 M.T.O. Mark No 3 M.T.O. Dimension
Size Length Area (cm²) Area (cm²) A H
26 510 1452 1948 649
28 536 1642 2080 693
30 561 1843 2212 737
32 300 x 10 586 10 Thk 2056 12 Thk 2344 781 100
34 Thk 612 Plate 2280 Plate 2476 825
36 Plate 637 2514 2608 869
38 663 2760 2740 913
40 688 3017 2872 957

Support No S5
Pipe Mark No 1 M.T.O. Mark No 2 M.T.O. Mark No 3 M.T.O. Dimension
Size Length Area (cm²) Area (cm²) A H
26 610 1737 1948 649
28 636 1949 2080 693
30 661 2172 2212 737
32 300 x 10 686 10 Thk 2407 12 Thk 2344 781 150
34 Thk 712 Plate 2652 Plate 2476 825
36 Plate 737 2909 2608 869
38 763 3177 2740 913
40 788 3456 2872 957

Pipe Size Max Vertical


(") Load (KN)
Assembly Tag No: - S1 or S5 - X 26 - 40 300.0

Detail No Pipe Size


SUPPORT No S1, S5
SUPPORT TYPE Welded Shoe, Standard Length Sheet A3
PIPE SIZE 26" - 40"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Beam shall be cut Seal Weld Notch to prevent


Longitudinally to form Shoe Crevice corrosion

25

Cut Notch into H


the Shoe

1 20

= =
500 100

Support Pipe Size Dimension Mark No 1 M.T.O. Max Vertical


Type H Length Load (KN)
S2 ½" - 6" 100 IPE 200 250
S6 ½" - 6" 150 IPE 200 500 40.0
S10 ½" - 6" 50 IPE 200 250

Assembly Tag No: - S2 or S6 or S10 - X


Detail No Pipe Size
SUPPORT No S2, S6, S10
SUPPORT TYPE Long Welded Shoe Sheet A4
PIPE SIZE ½" - 6"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
Seal Weld
Cradle if required Notch to
refer to Support C2 prevent
Crevice
25 corrosion

H B
2

1 20 20 30
(typ) (typ)
= = A
Cut Notch into
500 the Shoe
Support No S2
Pipe Mark No 1 M.T.O. Mark No 2 M.T.O. Dimension
Size Area (cm²) Area (cm²) A B H
8,10 1450 364 200
12,14 10 Thk 1700 10 Thk 504 250 10
16,18 Plate 1950 Plate 644 300 100
20,22 12 Thk 2200 784 350 12
24 Plate 2450 924 400

Support No S6
Pipe Mark No 1 M.T.O. Mark No 2 M.T.O. Dimension
Size Area (cm²) Area (cm²) A B H
8,10 1700 494 200
12,14 10 Thk 1950 10 Thk 684 250 10
16,18 Plate 2200 Plate 874 300 150
20,22 12 Thk 2450 1064 350 12
24 Plate 2700 1254 400

Support No S10
Pipe Mark No 1 M.T.O. Mark No 2 M.T.O. Dimension
Size Area (cm²) Area (cm²) A B H
8,10 1200 234 200
12,14 10 Thk 1450 10 Thk 324 250 10
16,18 Plate 1700 Plate 414 300 50
20,22 12 Thk 1950 504 350 12
24 Plate 2200 594 400

Max Vertical Load (KN)


Pipe Size Bare pipes Pipes with a re-pad
(") c.a. = 1.5 c.a. = 3.0 All Pipe Schedules
8 - 18 90.0 55.0 200.0
Assembly Tag No: - S2 or S6 or S10 - X 20 - 24 130.0 90.0 200.0

Detail No Pipe Size


SUPPORT No S2, S6, S10
SUPPORT TYPE Long Welded Shoe Sheet A5
PIPE SIZE 8" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 4
Stiffening Ring required for pipes 44" and larger
for Pipe Specs 150H26, 150K26 & 150P26

X
Y
Seal Weld
Notch
to prevent Cradle is
Crevice W 25 mandatory
corrosion (typ) Ref Support
No C2
180
H

= = = =
Cut Notches
75 for pipe sizes
into the Shoe
500 44",60",68"& 70"
50 for other pipe sizes
Stiffening Ring
where required
4 Profile to
Suit

1
θ° 6°
2

½" - 13 UNC x ½"


3
(12.7mm) deep thread
N = No of Gusset
Plates (Type
30 W
Shown N = 1)
(typ) (typ)
Gusset Plates
are to be evenly = =
15.9
spaced.
A
3.2
19
BOSS DETAIL

Welding Boss Layout - Required for Pipe Sizes 44", 60", 68" & 70" only

Weld Boss
Attachment
to Cradle
5 (8 off)
α° α°
180 180 β° β°

Assembly Tag No: - S2 or S6 - X


Detail No Pipe Size
SUPPORT No S2, S6
SUPPORT TYPE Long Welded Shoe Sheet A6
PIPE SIZE 26" - 92"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 4
Support Pipe Dimension No of
Type Size H T W θ (Deg) Gussets N
S2 26 - 40 100 12 10 30 0
S6 26 - 40 150 12 10 30 0
S6 42 - 70 150 15 12 15 1
S6 72 - 92 150 15 15 15 3

Welding Boss Details - Required for Pipe Sizes 44", 60", 68" & 70" only
Support Pipe Angle (Deg) Mark No 5 Total
Type Size α β (8 Off) Length
S6 44 24 19 Welding Bosses
S6 60 25 21.5 19 dia round bar 200
S6 68, 70 25 22.5
NOTE - Welding Bosses to be supplied by vendor

Support Pipe Mark No 1 M.T.O. Mark No 2 M.T.O. Mark No 3 M.T.O. Dim'n


No Size Area (cm²) Area (cm²) Area (cm²) A
26 2551 1452 3246 649
28 2678 1642 3466 693
30 2805 1843 3686 737
S2 32 10 Thk 2932 10 Thk 2056 12 Thk 3906 781
34 Plate 3059 Plate 2280 Plate 4126 825
36 3186 2514 4346 869
38 3313 2760 4566 913
40 3440 3017 4786 957
26 3051 1737 3246 649
28 3178 1949 3466 693
30 3305 2172 3686 737
S6 32 10 Thk 3432 10 Thk 2407 12 Thk 3906 781
34 Plate 3559 Plate 2652 Plate 4126 825
36 3686 2909 4346 869
38 3813 3177 4566 913
40 3940 3456 4786 957
42 6103 5335 5549 1110
44 6293 5783 5795 1159
46 6484 6249 6040 1208
48 6674 6733 6285 1257
52 12 Thk 7056 12 Thk 7753 6776 1355
54 Plate 7246 Plate 8290 7021 1404
56 7437 8844 7267 1453
S6 60 7818 10006 15 Thk 7758 1552
64 8199 11239 Plate 8248 1650
66 8390 11881 8494 1699
68 8580 12542 8739 1748
70 8771 13220 8984 1797
72 10605 13916 9230 1846
76 11038 15360 9720 1944
80 15 Thk 11472 15 Thk 16875 10211 2042
84 Plate 11906 Plate 18461 10702 2140
88 12339 20117 11193 2239
92 12773 21845 11683 2337
Support Pipe Pipe Dimensions Mark No.4 Area
Type Spec Size X Y (cm²)
44 80 2809
48 80 3065
52 80 3320
150H26 54 100 12 Thk 4310
S6 and 60 12 100 Plate 4788
150K26 68 100 5427
70 100 5586
76 100 6065
80 120 7661
84 120 8045
92 120 8811
150P26 56 10 120 10 Thk Plate (Note 1) 5363
NOTES 1- Material shall be the same as the pipe, namely A358 Gr 316/316L
Assembly Tag No: - S2 or S6 - X
Detail No Pipe Size

SUPPORT No S2, S6
SUPPORT TYPE Long Welded Shoe (Dimensions) Sheet A7
PIPE SIZE 26" - 92"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3
Clamps shall be at 45º
for pipes 3" - 6"
45o

H
2

10
1 (typ)
= =
300 100

Clamps shall be horizontal


for pipes ½" - 2"

Beam shall be cut


longitudinally to form Shoe

Support Pipe Size Dimension Mark No 1 M.T.O. Mark No 2 No Off


No H Length
S3 ½" - 6" 100 IPE 200 150 Pipe Clip 2
S7 ½" - 6" 150 IPE 200 300 No PC1 2
S11 ½" - 6" 50 IPE 200 150 2

Assembly Tag No: - S3 or S7 or S11 - X


Detail No Pipe Size

SUPPORT No S3, S7, S11


SUPPORT TYPE Standard Clamped Shoe Sheet A8
PIPE SIZE ½" - 6"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

o
45

3 H
B
2
10 30
1 (typ)
= = (typ)

300 A

Support No S3
Pipe Mark M.T.O. M.T.O. Mark M.T.O. Mark No 3 Dimension
Size No 1 Length Area (cm²) No 2 Area (cm²) (2 Off) A B H
8,10 300 x 10 290 364 200
12,14 Thk 340 10 Thk 504 Pipe 250 10
16,18 Plate 390 Plate 644 Clip 300 100
20,22 12 Thk 1320 784 No PC1 350 12
24 Plate 1470 924 400

Support No S7
Pipe Mark M.T.O. M.T.O. Mark M.T.O. Mark No 3 Dimension
Size No 1 Length Area (cm²) No 2 Area (cm²) (2 Off) A B H
8,10 300 x 10 340 494 200
12,14 Thk 390 10 Thk 684 Pipe 250 10
16,18 Plate 440 Plate 874 Clip 300 150
20,22 12 Thk 1470 1064 No PC1 350 12
24 Plate 1620 1254 400

Support No S11
Pipe Mark M.T.O. M.T.O. Mark M.T.O. Mark No 3 Dimension
Size No 1 Length Area (cm²) No 2 Area (cm²) (2 Off) A B H
8,10 300 x 10 240 234 200
12,14 Thk 290 10 Thk 324 Pipe 250 10
16,18 Plate 340 Plate 414 Clip 300 50
20,22 12 Thk 1170 504 No PC1 350 12
24 Plate 1320 594 400

Assembly Tag No: - S3 or S7 or S11 - X


Detail No Pipe Size
SUPPORT No S3, S7, S11
SUPPORT TYPE Standard Clamped Shoe Sheet A9
PIPE SIZE 8" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Clamps shall be at 45º


for pipes 3" - 6" 45
o

H
2

10
1 (typ)
= =
500 100

Clamps shall be horizontal


for pipes ½" - 2"

Beam shall be cut


longitudinally to form shoe

Support Pipe Size Dimension Mark No 1 M.T.O. Mark No 2 No Off


Type H Length
S4 ½" - 6" 100 IPE 200 250 Pipe Clip 2
S8 ½" - 6" 150 IPE 200 500 No PC1 2
S12 ½" - 6" 50 IPE 200 250 2

Assembly Tag No: - S4 or S8 or S12 - X


Detail No Pipe Size
SUPPORT No S4, S8, S12
SUPPORT TYPE Long Clamped Shoe Sheet A10
PIPE SIZE ½" - 6"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

o
45

3 H
B
2
10 30
1 (typ) (typ)
= =
500 A

Support No S4
Pipe Mark Area Mark Area Mark No 3 Dimension
Size No 1 (cm²) No 2 (cm²) (2 Off) A B H
8,10 1450 364 200
12,14 10 Thk 1700 10 Thk 504 Pipe 250 10
16,18 Plate 1950 Plate 644 Clip 300 100
20,22 12 Thk 2200 784 No PC1 350 12
24 Plate 2450 924 400

Support No S8
Pipe Mark M.T.O. Mark M.T.O. Mark No 3 Dimension
Size No 1 Area (cm²) No 2 Area (cm²) (2 Off) A B H
8,10 1700 494 200
12,14 10 Thk 1950 10 Thk 684 Pipe 250 10
16,18 Plate 2200 Plate 874 Clip 300 150
20,22 12 Thk 2450 1064 No PC1 350 12
24 Plate 2700 1254 400

Support No S12
Pipe Mark M.T.O. Mark M.T.O. Mark No 3 Dimension
Size No 1 Area (cm²) No 2 Area (cm²) (2 Off) A B H
8,10 1200 234 200
12,14 10 Thk 1450 10 Thk 324 Pipe 250 10
16,18 Plate 1700 Plate 414 Clip 300 50
20,22 12 Thk 1950 504 No PC1 350 12
24 Plate 2200 594 400

Assembly Tag No: - S4 or S8 or S12 - X

Detail No Pipe Size


SUPPORT No S4, S8, S12
SUPPORT TYPE Long Clamped Shoe Sheet A11
PIPE SIZE 8" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Existing Shoe Type S1 - S8

1
17 5

2
= = = =

200 A

Note: - For PTFE details and installation instructions refer to Spec No 60-0000-L-SPE-1003

Pipe Mark No 1 Area Mark No 2 No Off Dimension


Size (cm²) A
½" - 6" 5 Thk Polished Stainless 180 PTFE pad Type A. 1 90
8 Steel Plate ASTM-A-240 260 PTFE pad Type A. 1 130
10 - 14 Type 316 or Equivalent. 360 PTFE pad Type B. 1 180
16 - 24 560 PTFE pad Type C. 1 280

Assembly Tag No: - S19 - X


Detail No Pipe Size

SUPPORT No S19
SUPPORT TYPE PTFE for Pipe Shoe Sheet A12
PIPE SIZE ½" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Existing Shoe Type S1 - S10

17 5

= = = = 220
(typ) (typ)
200

Note: - For PTFE details and installation instructions refer to Spec No 60-0000-L-SPE-1003

Pipe Mark No 1 Area Mark No 2 No Off Dimension


Size (cm²) A
26 - 40 5 Thk Polished Stainless 880 PTFE pad Type C. 2 220
42 - 88 Steel Plate ASTM-A-240 1800 PTFE pad Type D. 2 300
Type 316 or Equivalent.

Assembly Tag No: - S19 - X


Detail No Pipe Size
SUPPORT No S19
SUPPORT TYPE PTFE for Pipe Shoe Sheet A13
PIPE SIZE 26" - 88"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
Clamps shall be at 45º
for pipes 3" - 6" 45o

H
2

10
1 (typ)
= =
300 100

Clamps shall be horizontal


for pipes ½" - 2"

Isolation Strip

Beam shall be cut


longitudinally to form Shoe

Support Pipe Size Dimension Mark No 1 M.T.O. Mark No 2 No Off


No H Length
S103 ½" - 6" 100 IPE 200 150 Pipe Clip 2
S107 ½" - 6" 150 IPE 200 300 No PC101 2
S111 ½" - 6" 50 IPE 200 150 2

Assembly Tag No: - S103 or S107 or S111 - X

Detail No Pipe Size


SUPPORT No S103, S107, S111
SUPPORT TYPE Clamped Shoe for Stainless Steel Pipes Sheet A14
PIPE SIZE ½" - 6"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3
Isolation Strip

45o

3 H
B
2
10 30
1 (typ)
= = (typ)

300 A

Support No S103
Pipe Mark M.T.O. M.T.O. Mark M.T.O. Mark No 3 Dimension
Size No 1 Length Area (cm²) No 2 Area (cm²) (2 Off) A B H
8,10 300 x 10 290 364 200
12,14 Thk 340 504 250 10
16,18 Plate 390 10 Thk 644 Pipe 300
20,22 12 Thk 1320 Plate 784 Clip 350 100
24, 26 Plate 1470 924 No PC101 400 12
28, 30 1770 1204 500
32 15 Thk Plt 1920 15 Thk Plt 1344 550 15
Support No S107
Pipe Mark M.T.O. M.T.O. Mark M.T.O. Mark No 3 Dimension
Size No 1 Length Area (cm²) No 2 Area (cm²) (2 Off) A B H
8,10 300 x 10 340 494 200
12,14 Thk 390 684 250 10
16,18 Plate 440 10 Thk 874 Pipe 300
20,22 12 Thk 1470 Plate 1064 Clip 350 150
24, 26 Plate 1620 1254 No PC101 400 12
28, 30 1920 1634 500
32 15 Thk Plt 1920 15 Thk Plt 1824 550 15
Support No S111
Pipe Mark M.T.O. M.T.O. Mark M.T.O. Mark No 3 Dimension
Size No 1 Length Area (cm²) No 2 Area (cm²) (2 Off) A B H
8,10 300 x 10 240 234 200
12,14 Thk 290 324 250 10
16,18 Plate 340 10 Thk 414 Pipe 300
20,22 12 Thk 1170 Plate 504 Clip 350 50
24, 26 Plate 1320 594 No PC101 400 12
28, 30 1620 774 500
32 15 Thk Plt 1920 15 Thk Plt 864 550 15
Assembly Tag No: - S103 or S107 or S111 - X
Detail No Pipe Size
SUPPORT No S103, S107, S111
SUPPORT TYPE Clamped Shoe for Stainless Steel Pipes Sheet A15
PIPE SIZE 8" - 32"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Clamps shall be at 45º


for pipes 3" - 6" 45o

H
2

10
1 = = (typ)

500 100

Clamps shall be horizontal


for pipes ½" - 2"

Isolation Strip

Beam shall be cut


longitudinally to form Shoe

Support Pipe Size Dimension Mark No 1 M.T.O. Mark No 2 No Off


Type H Length
S104 ½" - 6" 100 IPE 200 250 Pipe Clip 2
S108 ½" - 6" 150 IPE 200 500 No PC101 2
S112 ½" - 6" 50 IPE 200 250 2

Assembly Tag No: - S104 or S108 or S112 - X


Detail No Pipe Size
SUPPORT No S104, S108, S112
SUPPORT TYPE Long Clamped Shoe for Stainless Steel Pipes Sheet A16
PIPE SIZE ½" - 6"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3
Isolation Strip

45o

3
H
B
2
10 30
1 (typ) (typ)
= =

500 A

Support No S104
Pipe Mark Area Mark Area Mark No 3 Dimension
Size No 1 (cm²) No 2 (cm²) (2 Off) A B H
8,10 1450 364 200
12,14 10 Thk 1700 504 Pipe 250 10
16,18 Plate 1950 10 Thk 644 Clip 300 100
20,22 12 Thk 2200 Plate 784 No PC101 350
24 Plate 2450 924 400 12
30 2950 1204 500

Support No S108
Pipe Mark M.T.O. Mark M.T.O. Mark No 3 Dimension
Size No 1 Area (cm²) No 2 Area (cm²) (2 Off) A B H
8,10 1700 494 200
12,14 10 Thk 1950 684 Pipe 250 10
16,18 Plate 2200 10 Thk 874 Clip 300 150
20,22 12 Thk 2450 Plate 1064 No PC101 350
24 Plate 2700 1254 400 12
30 3200 1634 500

Support No S112
Pipe Mark M.T.O. Mark M.T.O. Mark No 3 Dimension
Size No 1 Area (cm²) No 2 Area (cm²) (2 Off) A B H
8,10 1200 234 200
12,14 10 Thk 1450 324 Pipe 250 10
16,18 Plate 1700 10 Thk 414 Clip 300 50
20,22 12 Thk 1950 Plate 504 No PC101 350
24 Plate 2200 594 400 12
30 2700 774 500
Assembly Tag No: - S104 or S108 or S112 - X
Detail No Pipe Size
SUPPORT No S104, S108, S112
SUPPORT TYPE Long Clamped Shoe for Stainless Steel Pipes Sheet A17
PIPE SIZE 8" - 30"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3

2
Pipe Size

180o
'A'
500
1

Pipe Size 'A' Mark No.1 Mark No.2


½" 34
¾" 42
1" 50
1½" 75
2" 95 Isolator Pad 500 Lg. 20mm Wide St. Stl.
3" 140 cut from 2mm thk. Bands- 2 off
4" 180 PTFE sheet
6" 265
8" 345
10" 430
12" 510

NOTES
1- Maximum operating temp of pipe = 150°C
2- For pipes 14" and larger or pipes with an operating temp greater than 150°C use a
cradle C101 or C102
3- PTFE sheet can be site trimmed to avoid clashes with elbow, flanges etc.
However it shall be ensured that none of the pipe is in direct contact the the
supporting steelwork

Assembly Tag No: - S113 - X


Detail No Pipe Size

SUPPORT No S113
SUPPORT TYPE Isolator Pad for St. Stl. Lines on C. Stl. Support Sheet A18
PIPE SIZE ½" - 12"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Supported pipe 3" NB Supporting pipe 8" NB


maximum minimum

1 Field
Weld

150 600
max. Alternative angle position
for pipe sizes 26"
L
and above

Size Code Dimn 'L' Mark No.1 Total Length


A 700 700
70x70x8L
B 1000 1000

Assembly Tag No: - S114 - X

Detail No Size Code


SUPPORT No S114
SUPPORT TYPE Pick-Up Sheet A19
PIPE SIZE Supported pipe 3" NB max. (Insulated)
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Supported pipe 3" NB Supporting pipe 8" NB


maximum minimum

8 100

Field Weld
50 50 Typ.
2 200

150 600
max.

2
Size Code Dimn 'L' Mark No.1 Total Length Mark No.2 Area (cm )
A 700 700 8 Thk.
70x70x8L 400
B 1000 1000 Plate

Assembly Tag No: - S115 - X

Detail No Size Code


SUPPORT No S115
SUPPORT TYPE Pick-Up Sheet A20
PIPE SIZE Supported pipe 3" NB max. (Uninsulated)
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3

PIPES WITH SHOES & GUIDES PIPES WITH SHOES & GUIDES
PIPE SIZE ≤ 4" PIPE SIZE ≥ 6"

Packing plate Packing plate


for gaps 20mm for gaps 20mm
or less. Material or less. Material
shall be site shall be site
supplied supplied

A A

min 20
A (typ) A
(typ)

PIPES WITH GUIDES ONLY PIPES WITH GUIDES ONLY


PIPE SIZE ≤ 14" PIPE SIZE ≥ 16"
Packing plate Packing plate
for gaps 20mm for gaps 20mm
or less. Material or less. Material
shall be site shall be site
supplied supplied
A A

min min
A (typ) A
(typ)

A 20
(typ)
20 = =
max A (Maximum
Pipe Size
Dimension)
½" - 24" 120
26" - 92" 200
Assembly Tag No: - PK1-A View A-A
Detail No
SUPPORT No PK1-A
SUPPORT TYPE Packing Plate for gaps up to 20mm for guides Sheet A21
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3
PIPES WITH SHOES ONLY
ALL SIZES

Packing plate
for gaps 20mm
or less. Material
shall be site
supplied

10
(typ) A

PIPES WITHOUT SHOES OR GUIDES


ALL SIZES

Packing plate
for gaps 20mm
or less. Material
shall be site Pipe Size L
supplied ½" - 6" 120
8" - 14" 250
A
16" - 24" 400
26" - 42" 600

A
A

20 = =
max A (Maximum
Pipe Size
Dimension)
½" - 24" 120
26" - 92" 200
Assembly Tag No: - PK1-A View A-A
Detail No
SUPPORT No PK1-A
SUPPORT TYPE Packing Plate for gaps up to 20mm for supports only Sheet A22
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Pipe Support Dimension Mark No 1


Size No L
½" - 4" PK2-A 250
6" - 10" PK2-B 400
12" - 24" PK2-C 600 UPN 160
1 26" - 30" PK2-D 1000
36" - 40" PK2-E 1200
42" PK2-F 1500
A

10 1

L A
Site trim to suit A

Pipe Support Dimension Mark No 1


Size No L
½" - 4" PK2-G 250
6" - 8" PK2-H 400 UPN 160
10" - 14" PK2-J 600
10 A
(typ)
L
Site trim to suit
1

A
Pipe Support Dimension Mark No 1
Size No L
16" - 24" PK2-K 600
26" - 32" PK2-L 800 UPN 160
34" - 42" PK2-M 1000

20
L A 160
gap
Site trim to suit between
21 and = =
NOTE - Check length of channel for potential clash
60 mm
with neighbouring pipe or guide before welding.
Site trim to dimensions shown if necessary.
Site trim flanges to suit the gap.
Assembly Tag No: - PK2-X View A-A
Detail No Size Code
SUPPORT No PK2
SUPPORT TYPE Packing Support for gaps from 21 to 60mm for guides Sheet A23
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3

UPN 160
Site trim flanges and
field weld to suit gap

1
Pipe Support Dimension Mark No 1
A Size No L
½" - 6" PK3-A 120
8" - 14" PK3-B 250
16" - 24" PK3-C 400 UPN 160
26" - 34" PK3-D 600
36" - 42" PK3-E 800

10
(typ)
L A
Site trim to suit

1
A
Pipe Support Dimension Mark No 1
Size No L
½" - 6" PK3-F 120
8" - 14" PK3-G 250 UPN 160
= = 16" - 24" PK3-H 400
26" - 42" PK3-J 600

L
Site trim to suit
A

gap
160
between
21 and = =
NOTE - Check length of channel for potential clash 60 mm
with neighbouring pipe or guide before welding.
Site trim to dimensions shown if necessary.
Site trim flanges to suit the gap.

View A-A
Assembly Tag No: - PK3-X
Detail No Size Code
SUPPORT No PK3
SUPPORT TYPE Packing Support for gaps from 21 to 60mm for supports Sheet A24
PIPE SIZE ½" - 42"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Pipe Support Dimension Mark No 1


Size No L
½" - 4" PK4-A 250
6" - 10" PK4-B 400
12" - 24" PK4-C 600 UPN 240
1 26" - 30" PK4-D 1000
36" - 40" PK4-E 1200
42" PK4-F 1500
A

10 1
(typ) L A
Site trim to suit A

Pipe Support Dimension Mark No 1


Size No L
½" - 4" PK4-G 250
6" - 8" PK4-H 400 UPN 240
10" - 14" PK4-J 600
10 A
(typ) L
Site trim to suit

A
Pipe Support Dimension Mark No 1
Size No L
16" - 24" PK4-K 600
26" - 32" PK4-L 800 UPN 240
34" - 42" PK4-M 1000

20
(typ) L A gap 240
Site trim to suit between
61 and = =
NOTE - Check length of channel for potential clash
80 mm
with neighbouring pipe or guide before welding.
Site trim to dimensions shown if necessary.
Site trim flanges to suit the gap.
Assembly Tag No: - PK4-X View A-A
Detail No Size Code
SUPPORT No PK4
SUPPORT TYPE Packing Support for gaps from 61 to 80mm for guides Sheet A25
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

1
Pipe Support Dimension Mark No 1
A Size No L
½" - 6" PK5-A 120
8" - 14" PK5-B 250
16" - 24" PK5-C 400 UPN 240
26" - 34" PK5-D 600
36" - 42" PK5-E 800

10
(typ)
L A

1
A Pipe Support Dimension Mark No 1
Size No L
½" - 6" PK5-F 120
8" - 14" PK5-G 250 UPN 240
= = 16" - 24" PK5-H 400
26" - 42" PK5-J 600

L A

gap
240
between
NOTE - Check length of channel for potential clash 61 and = =
with neighbouring pipe or guide before welding. 80 mm
Site trim to dimensions shown if necessary.
Site trim flanges to suit the gap.

View A-A
Assembly Tag No: - PK5-X
Detail No Size Code
SUPPORT No PK5
SUPPORT TYPE Packing Support for gaps from 61 to 80mm for supports Sheet A26
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Existing Shoe Type S2,S6,S10

1
17 5

2
= = = =

400 A

Note: - For PTFE details and installation instructions refer to Spec No 60-0000-L-SPE-1003

Pipe Mark No 1 Area Mark No 2 No Off Dimension


Size (cm²) A
½" - 6" 5 Thk Polished Stainless 360 PTFE pad Type A. 1 90
8 Steel Plate ASTM-A-240 520 PTFE pad Type A. 1 130
10 - 14 Type 316 or Equivalent. 720 PTFE pad Type B. 1 180
16 - 24 1120 PTFE pad Type C. 1 280

Assembly Tag No: - S20 - X


Detail No Pipe Size

SUPPORT No S20
SUPPORT TYPE PTFE for Long Pipe Shoe Sheet A27
PIPE SIZE ½" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Existing Shoe Type S2,S6,S10

17 5

= = = = 220
(typ) (typ)
400

Note: - For PTFE details and installation instructions refer to Spec No 60-0000-L-SPE-1003

Pipe Mark No 1 Area Mark No 2 No Off Dimension


Size (cm²) A
26 - 40 5 Thk Polished Stainless 1760 PTFE pad Type C. 2 220
42 - 88 Steel Plate ASTM-A-240 3600 PTFE pad Type D. 2 300
Type 316 or Equivalent.

Assembly Tag No: - S20 - X


Detail No Pipe Size
SUPPORT No S20
SUPPORT TYPE PTFE for Long Pipe Shoe Sheet A28
PIPE SIZE 26" - 88"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

Monolux Isolation
Block or equivalent.
Pipe Insulation

150

60 Thk

150

Supporting steelwork
= = by others
300

SECT Heat tubes

45o

250 Max
NOTE
1, For details of the SECT Traced Pipe Shoes refer to Specification No. 60-0000-L-SPE-1003.

Assembly Tag No: - S21 - X


Detail No Pipe Size
SUPPORT No S21
SUPPORT TYPE Pipe Shoe for SECT Traced piping Sheet A29
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

Seal Weld Notch to prevent Stiffening Ring


Crevice corrosion
X
Y

Cradle is
Mandatory
Ref Support
25
No C2
(typ)

180
W H

= = = =
Cut Notches into
the Shoe
500 50
(typ)

Stiffening Ring
4
Profile to
Suit

1
º
3θ 6º
2

30 W
(typ) (typ)

N = No of Gusset = =
Plates (Type Stiffening Ring Required for
Shown N = 1) A
Pipes 36"- 40"
Gusset Plates
are to be evenly
For Pipe Specs
spaced. 150H26, 150K26 & 150P26

For other Pipe Specs refer to


Assembly Tag No: - S13 or S14 - X
Support Nos S2 & S6

Detail No Pipe Size


SUPPORT No S13, S14
SUPPORT TYPE Long Welded Shoe for Spec Nos. 150H26 & 150K26 Sheet A30
PIPE SIZE 36" - 40"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

Support Pipe Dimension Angle No of


Type Size H T W θ (Deg) Gussets N
S13 36 - 40 100 12 10 30 0
S14 36 - 40 150 12 10 30 0

Support Pipe Mark No 1 M.T.O. Mark No 2 M.T.O. Mark No 3 M.T.O. Dim'n


Type Size Area (cm²) Area (cm²) Area (cm²) A
36 10 Thk 3186 10 Thk 2514 12 Thk 4346 869
S13 38 Plate 3313 Plate 2760 Plate 4566 913
40 3440 3017 4786 957
36 10 Thk 3686 10 Thk 2909 12 Thk 4346 869
S14 38 Plate 3813 Plate 3177 Plate 4566 913
40 3940 3456 4786 957

Support Pipe Pipe Dimensions Mark No.4 Area


Type Spec Size X Y (cm²)
150H26 36 12 80 12 Thk 2298
S13/S14
150K26 40 12 80 Plate 2554

SUPPORT No S13, S14


SUPPORT TYPE Long Welded Shoe - Spec Nos. 150H26 & 150K26 (Dims Sheet A31
PIPE SIZE 36" - 40"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 1

UPN 200
Site trim flanges
and stiffening plates.
Field weld to suit gap

1 B B
A

500 500
(Centres of stiffening plates)

10
(typ) L A
Site trim to suit

gap 10 Thk Stiffening


200
between 2 Plate, to be welded
21 and = = at 500 centres.
60 mm

View A-A View B-B

Pipe Support Dimension Mark No 1 Mark No 2 No Off Total Area


2
Size No L (cm )
44" - 52" PK3-K 1400 3 300
54" - 60" PK3-L 1600 10 Thk 3 300
64" - 68" PK3-M 1800 UPN 200 Stiffening 3 300
70" - 76" PK3-N 2000 Plate 3 300
78" - 84" PK3-P 2200 5 500
88" - 92" PK3-Q 2400 5 500
NOTE - Check length of channel for potential clash
with neighbouring pipe or guide before welding.
Site trim to dimensions shown if necessary.

Assembly Tag No: - PK3-X


Detail No Size Code
SUPPORT No PK3
SUPPORT TYPE Packing Support for gaps from 21 to 60mm for supports Sheet A32
PIPE SIZE 44" - 92"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

A
X Y

A
Stiffening Ring

Stiffening Ring shall be


supplied in two halves
1

Stiffening Ring Required for


Pipe 36" and Above
For Pipe Specs
150H26, 150K26 & 150P26
for Pipes subjected to Vacuum
or where required by the
View A-A
stress engineer
Support Pipe Pipe Dimensions Mark No.1 Area
Type Spec Size X Y (cm²)
36 80 2500
40 80 2755
44 80 3010
48 80 3266
52 80 3521
54 100 4624
SR1 150H26 60 12 100 12 Thk 5103
and 64 100 Plate 5422
150K26 66 100 5581
68 100 5741
70 100 5901
76 100 6380
80 120 8114
84 120 8497
92 120 9263
SR101 150P26 56 10 120 10 Thk Plate (Note 1) 5815
NOTES 1- Material shall be the same as the pipe, namely A358 Gr 316/316L

Assembly Tag No: - SR1 or SR101 - X


Detail No Pipe Size
SUPPORT No SR1, SR101
SUPPORT TYPE Stiffening Rings Sheet A33
PIPE SIZE 36" - 92"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

Pipe Insulation
Monolux Isolation 150
Block or equivalent.

60 Thk

150

Supporting steelwork
= = by others
300

SECT Heat tubes

45o

250 Max
NOTE
1, For details of the SECT Traced Pipe Shoes refer to Specification No. 60-0000-L-SPE-1003.

Assembly Tag No: - S22 - X


Detail No Pipe Size
SUPPORT No S22
SUPPORT TYPE Double Pipe Shoe for SECT Traced piping Sheet A34
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

Piping Nozzle
A A
Y

Puddle Flange
Sump Cover

Puddle Flange
Puddle Flange shall be
1 supplied in two halves

View A-A

Support Pipe Dimensions Mark No.1 Area


Type Size X Y (cm²)
¾ 10 50 121
1 10 50 130
1½ 10 50 10 Thk 154 PF1
2 10 50 Plate 173 Puddle Flange for
PF1 3 10 50 218 Carbon Steel
4 10 50 258 Piping
6 12 50 12 Thk 342
8 12 50 Plate 423
10 15 50 15 Thk 507
12 15 50 Plate 588
Support Pipe Dimensions Mark No.1 Area
Type Size X Y (NOTE -1) (cm²)
PF101
¾ 10 50 121
Puddle Flange for
1 10 50 130
Stainless Steel
1½ 10 50 10 Thk 154
Piping
2 10 50 Plate 173
PF101 3 10 50 218 NOTE -1
4 10 50 258 Material shall be the
6 12 50 12 Thk 342 same as the pipe,
8 12 50 Plate 423 namely A358 Gr
10 15 50 15 Thk 507 316/316L
12 15 50 Plate 588
Assembly Tag No: - PF1 or PF101 - X
Detail No Pipe Size
SUPPORT No PF1, PF101
SUPPORT TYPE Puddle Flanges for Sump Covers Sheet A35
PIPE SIZE ¾" - 12"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

18º
30º
3
10 H
2
4
12 30 10
(typ) (typ)
= =
= =
A
300 75
(typ)

Pipe Mark No 1 M.T.O. Mark No 2 M.T.O. Mark No 3 M.T.O. Dimension


Size Length Area (cm²) Area (cm²) A H
300 x 10 10 Thk 12 Thk
28 Thk 536 Plate 1642 Plate 2080 693 100
Plate

Pipe Mark No 4
Size
10 Thk C.S. Plate.
28 Support as C1-28 except: -
Length =450, developed angle = 144º

Pipe Size Max Vertical


(") Load (KN)
28 300.0

Assembly Tag No: - S15 - X


Detail No Pipe Size
SUPPORT No S15
SUPPORT TYPE Welded Shoe for Contra traced pipes Sheet A36
PIPE SIZE 28"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Cradle for Stainless lines only


See Note 1

100

1
100 2 gap Do not weld this
(typ) face of shear lug.
Seal gap with
mastic after
welding.

Pipe Mark No 1 Area Maximum Anchor


Size (cm²) Load (KN)
½-4 10 Thk 200 5.0
Plate

Notes 1- Cradle is mandatory for stainless steel lines 2" - 4". Refer to Support No C3
2- For stainless steel lines ½" - 1½" use Support No DA101
3- Cradles shall not be used for Carbon Steel lines

Assembly Tag No: - DA1


Detail No
SUPPORT No DA1
SUPPORT TYPE Directional Anchor - Bare Lines Sheet B1
PIPE SIZE ½" - 4"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Cradle if required
Ref. Support No C3 1
See Note 1

75

4 gap
H
150

10 10
L 2 gap
2
(typ) = =

Pipe Size Maximum Anchor Load (KN)


No Cradle With Cradle
6 - 14 15.0 40.0

Pipe Size Mark No 1 Total Mark No 2 Area Dimensions


Length (cm²) A L H
6 712 495 165 160 178
8 150 x 10 736 10 Thk 600 200 160 184
10 Plate 752 Plate 690 230 160 188
12 792 810 270 160 198
14 824 900 300 160 206

Notes 1- Cradle is mandatory for stainless steel lines. Refer to Support No C3

Assembly Tag No: - DA1 - X


Detail No Pipe Size
SUPPORT No DA1
SUPPORT TYPE Directional Anchor - Bare Lines Sheet B2
PIPE SIZE 6" - 14"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Cradle is mandatory
Ref. Support No C3

75 H

4 gap
150
1
10 10
2 T T 2 gap
1
(typ) = =

L A

Pipe Maximum Anchor


Size Load (KN)
16 - 24 50.0
26 - 40 100.0

Pipe Size Mark No 1 Area Mark No 2 Area Dimensions


(cm²) (cm²) A L T H
16 1125 1200 250 200 10 178
18 10 Thk 174
20 Plate 184
22 1350 1200 300 200 10 181
24 178
26 10 Thk 187
28 1575 Plate 1500 350 250 12 184
30 182
32 12 Thk 191
34 Plate 188
36 1800 1500 400 250 12 186
38 184
40 182

Assembly Tag No: - DA1 - X


Detail No Pipe Size
SUPPORT No DA1
SUPPORT TYPE Directional Anchor - Bare Lines Sheet B3
PIPE SIZE 16" - 40"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 4

Cradle for Stainless lines only Gusset plates


See Note 1 required on 3"
and 4" pipes
only

25

80 H
1

2 100

3
Do not weld
50 2 Gap 100 this side of 10
(typ) (typ) Shear lug
= = 15
(typ)
600 100

NOTE - Lugs shall be tack welded to the


H = 100 for Support No DA2
shoe in the shop. The final weld shall be
H = 150 for Support No DA3
made in the field.

Pipe Maximum Anchor


Size Load (KN)
½-4 12.0

Pipe Size Mark No 1 Length Mark No 2 Area (cm²) Mark No 3 Area


DA2 DA3 DA2 DA3 (cm²)
½-2 IPE 200 300 600 10 Thk 200
3-4 IPE 200 300 600 10 Thk Plt 200 300 Plate 200

Notes 1- Cradle is mandatory for stainless steel lines 2" - 4". Refer to Support No C103
2- For stainless steel lines ½" - 1½" use Support No DA102
3- Cradles shall not be used for Carbon Steel lines

Assembly Tag No: -DA2,DA3 - X Dimensions Required: - None


Detail No Pipe Size
SUPPORT No DA2, DA3
SUPPORT TYPE Directional Anchor for Insulated Pipes Sheet B4
PIPE SIZE ½" - 4"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
Cradle if Cut
required 35 = = = = Notches
Ref. Support (typ) into
No C3 or C103. Anchor
Cradle is W 25
mandatory for
SS pipes

1 H
T

20 150
3

Do not weld 2 Gap


this side of (typ)
Shear lug L
(typ)
NOTE - Lugs shall be tack welded to the H = 100 for Support No DA2
shoe in the shop. The final weld shall be H = 150 for Support No DA3
made in the field.
Pipe Size Maximum Anchor Load (KN)
No Cradle With Cradle
6-8 25.0 100.0
10 - 24 50.0 200.0

Pipe Dimension
2
Size A L T W
6-8 150 600
10 200 600
12 250 700 10
14 250 700 10
16 300 700
18 300 800
30 20 - 22 350 800 12
(typ) 24 400 800
A
Pipe Dimension Mark No 1 DA2 DA3 Mark No 2 Area Mark No 3 Total
Size H Area (cm²) Area (cm²) (cm²) Length
6 891 1326 900
8 891 1326 900 HEA 100 300
10 1086 1596 10 Thk 1200
12 (See 1371 2006 Plate 1750
14 Note 1) 10 Thk 1371 2006 1750 HEA 160 300
16 Plate 1566 2276 2100
18 1656 2416 2400
20 1851 2686 12 Thk 2800 HEA 200 300
22 1851 2686 Plate 2800
24 2046 2956 3200
Assembly Tag No: -DA2 or DA3 - X
Detail No Pipe Size
SUPPORT No DA2, DA3
SUPPORT TYPE Directional Anchor for Insulated Pipes Sheet B5
PIPE SIZE 6" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 5
Stiffening Ring required for pipes 44" and larger
for Pipe Specs 150H26, 150K26 & 150P26
X Y

= = =
25 Cut Notches
(typ) into Anchor

80
W H

T 75
75
C
Cradle is (typ) B 2 gap NOTE - Lugs shall
Mandatory (typ) be tack welded to
Ref Support L the shoe in the shop.
No C3 The final weld shall
be made in the field.
6 Profile to
Suit

Pipe Maximum Anchor


θ 1 Size Load (KN)
6
26 - 92 400.0
2

3 ½" - 13 UNC x ½"


N = No of Gusset (12.7mm) deep thread
4
Plates.
Gusset Plates
20 W 5
are to be evenly
spaced (typ)
D 15.9

W
30 (typ) 3.2
19
(typ) = =
BOSS DETAIL
A

Welding Boss Layout - Required for Pipe Size 60" & 70" only

Weld Boss
Attachment
to Cradle
5 (16 off)
25° 25°
233 188 188 233 α α

Assembly Tag No: -DA2 or DA3 - X α = 22.5° for 70" pipe


α = 21.5° for 60" pipe
Detail No Pipe Size
SUPPORT No DA2, DA3
SUPPORT TYPE Directional Anchor for Insulated Pipes Sheet B6
PIPE SIZE 26" - 92"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 5
Support Pipe Dimension
Type Size H T W C B L D
DA2 26 - 40 100 12 10 10 250 900 400
DA3 26 - 40 150 12 10 10 250 900 400
DA3 42 - 70 150 15 15 12 300 1000 500
DA3 72 - 92 150 15 15 15 350 1100 700
Support Pipe Angle No of Support Pipe Mark No 5 Total
Type Size θ (Deg) Gussets N Type Size (16 Off) Length
DA2,DA3 26 - 40 30 0 Welding
DA3 42 - 70 15 1 DA3 70 Bosses 400
DA3 72 - 92 15 3 19 dia bar
NOTE - Welding Bosses to be supplied by vendor
Support Pipe Mark No 1 Area Mark No 2 Area Mark No 3 Area Dimension
Type Size (cm²) (cm²) (cm²) A
26 4592 1452 5843 649
28 4820 1642 6239 693
30 5049 1843 6635 737
DA2 32 10 Thk 5278 10 Thk 2056 12 Thk 7031 781
34 Plate 5506 Plate 2280 Plate 7427 825
36 5735 2514 7823 869
38 5963 2760 8219 913
40 6192 3017 8615 957
26 5492 1737 5843 649
28 5720 1949 6239 693
30 5949 2172 6635 737
DA3 32 10 Thk 6178 10 Thk 2407 12 Thk 7031 781
34 Plate 6406 Plate 2652 Plate 7427 825
36 6635 2909 7823 869
38 6863 3177 8219 913
40 7092 3456 8615 957
42 12205 5335 11098 1110
44 12586 5783 11589 1159
46 12968 6249 12080 1208
48 13349 6733 12571 1257
DA3 52 12 Thk 14111 7753 13552 1355
54 Plate 14492 8290 14043 1404
56 14874 8844 14534 1453
60 15636 15 Thk 10006 15 Thk 15515 1552
64 16398 Plate 11239 Plate 16496 1650
66 16780 11881 16987 1699
68 17161 12542 17478 1748
70 17542 13220 17969 1797
72 23331 13916 20305 1846
76 24284 15360 21385 1944
DA3 80 15 Thk 25238 16875 22465 2042
84 Plate 26192 18461 23544 2140
88 27146 20117 24624 2239
92 28100 21845 25703 2337
Support Pipe Mark No 4 Area Mark No 5 Area
Type Size (Plate) (cm²) (Plate) (cm²)
DA2,DA3 26 - 40 10 Thk 1800 10 Thk 1035
DA3 42 - 70 12 Thk 2250 12 Thk 1242
DA3 72 - 92 15 Thk 3150 15 Thk 1440
Support Pipe Pipe Dimensions Mark No.6 Area
Type Spec Size X Y (cm²)
44 80 2809
48 80 3065
52 80 3320
150H26 54 100 12 Thk 4310
S6 and 60 12 100 Plate 4788
150K26 68 100 5427
70 100 5586
76 100 6065
80 120 7661
84 120 8045
92 120 8811
150P26 56 10 120 10 Thk Plate (Note 1) 5363
NOTES 1- Material shall be the same as the pipe, namely A358 Gr 316/316L
SUPPORT No DA2, DA3
SUPPORT TYPE Directional Anchor for Insulated Pipes (Dimensions) Sheet B7
PIPE SIZE 26" - 92"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

2 gap
Do not weld this
(typ)
face of the guide

Existing Shoes

Guides are to be orientated as shown above

Size Pipe Size Dimension Mark No 1 Total


Code H Length
A ½"- 4" 30 50 x 6 Angle 60
B 6" - 24" 50 80 x 8 Angle 100
C 26" - 40" 100 100 x 10 Angle 200
D 42" - 92" 100 HEA 160 200

Assembly Tag No: - HG1 - X


Detail No Size Code
SUPPORT No HG1
SUPPORT TYPE Horizontal Guide for Insulated Pipes Sheet B8
PIPE SIZE ½" - 92"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

2 gap
(typ)
1

Existing Pipes

Guides are to be orientated as shown above

Size Pipe Size Dimension Mark No 1 Total


Code H Length
A ½"- 1½" 50 100
50 x 6 Angle
B 2" - 4" 100 200
C 6" - 8" 150 60 x 6 Angle 300
D 10"- 14" 200 80 x 8 Angle 400

Assembly Tag No: - HG2 - X


Detail No Size Code
SUPPORT No HG2
SUPPORT TYPE Horizontal Guide for Bare Pipes Sheet B9
PIPE SIZE ½" - 14"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

3 gap

W (typ)
45

H
1

Size Pipe Size Dimension Mark No 1 Total


Code H W Length
E 16" - 24" 150 100 100 x 10 Angle 440
F 26" - 40" 250 120 HEA 160 720

Assembly Tag No: - HG2 - X


Detail No Size Code
SUPPORT No HG2
SUPPORT TYPE Horizontal Guide for Bare Pipes Sheet B10
PIPE SIZE 16" - 40"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

30
12

25 2 Gap
(typ)
50

Size Pipe Mark Total


Code Size No 1 Length
A ½" - 6" 50 x 10 60
Plate

Assembly Tag No: - HG3 - X


Detail No Size Code
SUPPORT No HG3
SUPPORT TYPE Hold-down Guide for Insulated Pipes Sheet B11
PIPE SIZE ½" - 6"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
Trim to suit and
weld to existing
1 steel or vessel clip

20 600

ELEVATION
Alternative
connection
Ref Support to steel.
No SB9 or SB109 Field Weld (Elevation) 20
L

PLAN View X-X

Pipe Mark Length


Size No 1
½
¾ 60 x 6
1 Angle 600

2

Assembly Tag No: - VG1 - X


Detail No PipeSize
SUPPORT No VG1
SUPPORT TYPE Vertical Guide for All Pipes Sheet B12
PIPE SIZE ½" - 2"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
Trim to suit and
weld to existing
1 2 steel or vessel clip

20

20 600

Elevation

Plan

Notes: - 1- For maximum allowable "L" see Table below.


2- U-Bolts, Hold-down guides and shoes are to be called up separately.

Pipe Mark Max Mark Length


Size No 1 Length No 2
½
¾
1 70 x 8 1200 UPN 100 600
1½ Angle
2

Assembly Tag No: - VG2 - X


Detail No PipeSize
SUPPORT No VG2
SUPPORT TYPE Vertical Guide for 2 or more pipes Sheet B13
PIPE SIZE ½" - 2"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
Existing Shoe Trim to suit and
3 weld to existing
2 1 steel or vessel clip

20 650
L

Elevation

50
Alternative
25
30 connection
15
to steel. 20
57 Field Weld L

=
200
=
2 Gap Plan

Pipe Size Mark Mark Mark Area Dimension


2
Bare Insulated No 1 Length No 2 Length No 3 (cm ) L (Max)
Pipes Pipes
2-4 2-4 UPN 80 x 8 10 Thk 750
100 650 Angle 200 Plate 60
6 6 850

Assembly Tag No: - VG3 - X


Detail No Pipe Size
SUPPORT No VG3
SUPPORT TYPE Vertical Guide for All Pipes Sheet B14
PIPE SIZE 2" - 6"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
Trim to suit and
2 2 weld to existing
steel or vessel clip

1
130

Elevation

L
K

Guides shall be Alternative


welded 20mm below Existing Shoe connection
top face of angle. to steel
3 (Elevation) 20
10 L
(typ)

Pipe Support
3 Gap 3 Gap θ° Nos VG5 &
(typ) VG6. Guide
(typ)
for Insulated
Pipes 8" - 24"
A
Field weld
30 bracing where req'd
30 30° ≤ θ ≤ 60°

Plan A Bracing req'd when this


dimension > 300mm

Note
Pipe Support No VG4. Guide for Bracing
Non-Insulated Pipes 8" - 24" omitted
3 Gap for clarity
Note: - (typ)
For Bare Pipes use Support No VG4
For Pipes with an Insulation Thickness ≤ 75mm use Support No VG5
For Pipes with an Insulation Thickness ≥ 75mm use Support No VG6
Assembly Tag No: - VG4 or VG5 or VG6 - X
Detail No Pipe Size
SUPPORT No VG4, VG5, VG6
SUPPORT TYPE 4- Directional Vertical Guide for All Pipes Sheet B15
PIPE SIZE 8" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Pipe Pipe Mark Mark Mark No 3 Maximum Horizontal


Size O.D. No 1 Length No 2 Length VG5,VG6 Loads (KN)
8 219 2700 2525
10 273 UPN 160 2700 2579 5.0
12 324 3200 3030 10 Thk
14 356 3200 UPN 100 3062 Plate
16 406 3500 3352 8.0
18 457 3500 3403 Area =
2
20 508 UPN 200 4000 3854 36 cm
22 559 4000 3905 10.0
24 610 4000 3956

Dimensions
Pipe Pipe Pipe Sup't Pipe Sup't Pipe Sup't All Pipe
Size O.D. VG4 VG5 VG6 Supports
A A A K L (Max)
8 219 225 425 525 1350 900
10 273 279 479 579 1350 900
12 324 330 530 630 1600 1100
14 356 362 562 662 1600 1100
16 406 412 612 712 1750 1200
18 457 463 663 763 1750 1200
20 508 514 714 814 2000 1400
22 559 565 765 865 2000 1400
24 610 616 816 916 2000 1400

SUPPORT No VG4, VG5, VG6


SUPPORT TYPE 4- Directional Vertical Guide for All Pipes (Dimensions) Sheet B16
PIPE SIZE 8" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
2 2 Trim to suit and
weld to existing
steel or vessel clip
1
130

Elevation

L
K
Alternative
Existing Shoe connection
For correct orientation to steel
10 of shoes refer to the iso. (Elevation) 20
(typ) L

Pipe Support
3 Gap θ° No VG9 &
(typ) VG10. Guide
for Insulated
Pipes 4" - 24"
A Field weld
bracing where req'd
30° ≤ θ ≤ 60°

Plan A Bracing req'd when this


dimension > 300mm
C
B 3 Gap
75 (typ)
75 (typ) (typ)

Note
Bracing
C B omitted
for clarity

2 Gap
(typ)
Pipe Support No VG7. Pipe Support No VG8
Guide for Non-Insulated Pipes 4" - 24" Guide for Non-Insulated Pipes 4" - 24"
Note: - For Bare Pipes use Support No VG7 or VG8
For Pipes with an Insulation Thickness ≤ 75mm use Support No VG9
For Pipes with an Insulation Thickness ≥ 75mm use Support No VG10
Assembly Tag No: - VG7 or VG8 or VG9 or VG10 - X
Detail No Pipe Size
SUPPORT No VG7, VG8, VG9, VG10
SUPPORT TYPE 2-Directional Vertical Guide for All Pipes Sheet B17
PIPE SIZE 4" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Pipe Pipe Mark Mark Maximum Horizontal


Size O.D. No 1 Length No 2 Length Loads (KN)
4 114 UPN 100 2200 2606
6 168 2200 2822
8 219 2700 3026 5.0
10 273 UPN 160 2700 3242
12 324 3200 3446
14 356 3200 UPN 100 3574
16 406 3500 3776 8.0
18 457 3500 3979
20 508 UPN 200 4000 4182
22 559 4000 4385 10.0
24 610 4000 4588

Dimensions
Pipe Pipe Pipe Sup't Pipe Sup't Pipe Sup't All Pipe All Pipe
Size O.D. VG7/8 VG9 VG10 Supports Supports
B C A A K L (Max)
4 114 264 120 320 420 1100 700
6 168 318 174 374 474 1100 700
8 219 369 225 425 525 1350 900
10 273 423 279 479 579 1350 900
12 324 474 330 530 630 1600 1100
14 356 506 362 562 662 1600 1100
16 406 556 412 612 712 1750 1200
18 457 607 463 663 763 1750 1200
20 508 658 514 714 814 2000 1400
22 559 709 565 765 865 2000 1400
24 610 760 616 816 916 2000 1400

SUPPORT No VG7, VG8, VG9, VG10


SUPPORT TYPE 2-Directional Vertical Guide for All Pipes (Dimensions) Sheet B18
PIPE SIZE 4" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
Existing Trunnion T1
or Support for Small
Bore Piping SB7 or SB8
Site Trim to suit
and weld to existing
Column/Post 150
or Vessel Clip

30
3

20

700 (Site Trim ) A

Elevation
3
1 2

10

300

Plan
80

Notes: - 1- Support shall not be welded to a beam


2- Maximum trunnion size = 6"
3- For Pipes ≥ 2", Dimension "A" = 125
4- For Pipes ≤ 1½", Dimension "A" = 30 (Insulation shall be Site Trimmed)

Size Mark M.T.O. Mark M.T.O. Mark M.T.O. Max Loads (KN)
Code No 1 Length No 2 Length No 3 Area (cm2) Vertical Horizontal
A HEA 100 700 HEA 100 300 10 Thk 150 5.0 1.5
B HEA 160 700 HEA 100 300 Plate 250 10.0 3.0

Assembly Tag No: - VS1 - X


Detail No Size Code
SUPPORT No VS1
SUPPORT TYPE Cantilever Support for Vertical Pipes Sheet B19
PIPE SIZE ½" - 8"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Existing Trunnion T1
Site Trim to suit
and weld to existing
Column/Post 150
or Vessel Clip

30
3

45º
20

700 A
(Site Trim to Suit)

2
3

1 2

10

300

Plan
80

Notes: - 1- For Pipes ≥ 2", Dimension "A" = 125

Size Mark M.T.O. Mark M.T.O. Mark M.T.O. Max Loads (KN)
Code No 1 Length No 2 Length No 3 Area (cm2) Vertical Horizontal
A HEA 100 700 HEA 100 1200 10 Thk 150 6.5 2.0
B HEA 160 700 HEA 100 1200 Plate 250 15.0 4.5

Assembly Tag No: - VS2 - X


Detail No Size Code

SUPPORT No VS2
SUPPORT TYPE Braced Cantilever Support for Vertical Pipes Sheet B20
PIPE SIZE 2" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
Site Trim to suit Existing Trunnion T1
and weld to existing or Support for Small
Column/Post Bore Piping SB7 or
or Vessel Clip SB8

700 (Site Trim to Suit) A

Elevation

Field Weld

1
L

Plan Alternative
connection
Site Trim to Suit
to steel
(Elevation)
20
Notes: - 1- For Pipes ≥ 2", Dimension "A" = 125
2- For Pipes ≤ 1½", Dimension "A" = 30 (Insulation shall be Site Trimmed)
Maximum Allowable
Size Dimension Mark M.T.O. Loads (KN)
Code L No1 Length Vertical Horizontal
A1 1000 UPN 100 2400 2.0 0.5
B1 1000 UPN 160 2400 4.0 1.0
B2 2000 3400 3.0 1.0
C1 1000 2400 10.0 3.0
C2 2000 UPN 200 3400 7.0 2.0
C3 3000 4400 5.0 1.5
C4 4000 5400 3.0 1.0
Assembly Tag No: - VS3 - XX
Detail No Size Code
SUPPORT No VS3
SUPPORT TYPE Horizontal Frame Support and Guide for Vertical Pipes Sheet B21
PIPE SIZE ½" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
Site Trim to suit 1
and weld to existing Existing Trunnion
Column/Post T1, or Support
or Vessel Clip for Small Bore
Piping SB7
or SB8

45º
100

700 A
(Site Trim to Suit)

2
Elevation

Field Weld

1
L

Plan Site Trim to Suit

Notes: - 1- For Pipes ≥ 2", Dimension "A" = 125


2- For Pipes ≤ 1½", Dimension "A" = 30 (Insulation shall be Site Trimmed)

Maximum Allowable
Size Dimension Mark M.T.O. Mark M.T.O. Loads (KN)
Code L No 1 Length No 2 Length Vertical Horizontal
A1 1000 UPN 160 2400 UPN 100 1750 12.0 3.0
A2 2000 3400 1750 10.0 2.0
B1 1000 2400 1750 20.0 6.0
B2 2000 UPN 200 3400 UPN 160 1750 15.0 4.5
B3 3000 4400 1750 8.0 2.5
B4 4000 5400 1750 4.0 1.5
Assembly Tag No: - VS4 - XX
Detail No Size Code
SUPPORT No VS4
SUPPORT TYPE Braced Horizontal Frame Support for Vertical Pipes Sheet B22
PIPE SIZE ½" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
Site Trim to suit Existing Vertical
and weld to existing Trunnion Load
Column/Post
or Vessel Clip 2

Elevation

125
800 B
(Site Trim to Suit)
Field Weld
Tangential
Load 10
(Typ)

125

Radial Load
A
A + 75

Plan Field Weld


10
(Typ)

Pipe Dimension Mark M.T.O. Mark M.T.O. Vessel


Size A B No 1 Length No 2 Length Clip Type
2 310 155 2090 480
3 340 170 2120 510
4 365 183 UPN 200 2145 80 x 8 535 2B
6 420 210 2200 Angle 590 (Ref only)
8 470 235 2250 640
10 525 263 2305 695

Pipe Maximum Loads (KN)


Size Vertical Radial Tangential
2 - 10 10.0 3.0 2.0
Assembly Tag No: - VS5 - XX
Detail No Pipe Size
SUPPORT No VS5
SUPPORT TYPE Support from Vessels for Vertical Pipes Sheet B23
PIPE SIZE 2" - 10"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Site Trim to suit Existing Vertical


and weld to existing Trunnion Load
Column/Post
or Vessel Clip 3

45º
Elevation
2
L
125
min

L (Site Trim to Suit) B

Field Weld
Tangential Load
10
(Typ)

125

Radial Load
A

Field Weld
Plan 10
(Typ)

Assembly Tag No: - VS6 - XX


Detail No Pipe Size
SUPPORT No VS6
SUPPORT TYPE Support from Vessels for Vertical Pipes Sheet B24
PIPE SIZE 4" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Pipe Dimension Maximum Loads (KN)


Size A B L Vertical Radial Tangential
4 365 183
6 420 210 800 45.0 10.0 5.0
8 470 235
10 525 263
12 575 288 900
14 605 303
16 655 328
18 710 355 1100 170.0 30.0 12.0
20 760 380
22 810 405 1300
24 860 430

Pipe Mark M.T.O. Mark M.T.O. Mark M.T.O.


Size No 1 Length No 2 Length No 3 Length
4 2185 2262 725
6 HEA 160 2240 HEA 100 2262 780
8 2290 2262 830
10 2345 2262 885
12 2595 2545 100 x 10 1015
14 2625 2545 Angle 1045
16 3075 3111 1095
18 HEA 200 3130 HEA 160 3111 1150
20 3180 3111 1200
22 3630 3676 1250
24 3680 3676 1300

SUPPORT No VS6
SUPPORT TYPE Support from Vessels for Vertical Pipes (Dimensions) Sheet B25
PIPE SIZE 4" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
'A'

Existing Trunnion
See Isometric.

See Note 2

Existing
Steel

'A'
Pipe

See Note 2

Existing
Steel

Note
1. To be specified only when indicated on Stress Sketch.
2. For details of Rigid Strut and Clamp see Specification No. 60-0000-L-SPE-1003.

Support Pipe or Trunnion Dimension 'A' Maximum


Type Size (Minimum) Load (KN)

Refer to Vendor
Catalogue
RS1 2" - 36" for dimension "A"
and Maximum
Allowable Load

Assembly Tag No: - RS1 - X


Detail No. Trunnion Size

SUPPORT No RS1
SUPPORT TYPE Rigid Strut with Trunnion and Clamp Sheet B26
PIPE SIZE All Pipes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Existing
Shoe
'A'

See Existing
Note 1 Steel

Size Dimension 'A' Maximum


Code (Minimum) Load (KN)

Refer to Vendor
Catalogue
RS2 for dimension "A"
and Maximum
Allowable Load

Note
1. To be specified only when indicated on Stress Sketch.
2. For details of Rigid Strut see Specification No. 60-0000-L-SPE-1003.

Assembly Tag No.: - RS2

Detail No.

SUPPORT No RS2
SUPPORT TYPE Rigid Strut with Shoe Sheet B27
PIPE SIZE All Pipes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

1 2
Pipe Size

180o
150 'A'

50
2 Gap 3
typ

Pipe Size 'A' Mark No.1 Mark No.2 Mark No.3 Area
¾" 43 Isolator Pad 200 Lg. 20mm Wide St. Stl. 5 Thk Stainless Steel
1" 50 cut from 2mm thk. Bands- 2 off plate ASTM-A-240 150 cm2
1½" 75 PTFE sheet. Type 316 or
Site trim if required equivalent

Assembly Tag No: - DA101 - X


Detail No Pipe Size

SUPPORT No DA101
SUPPORT TYPE Line Stop for Non-Insulated Stainless Steel Pipes Sheet B28
PIPE SIZE ¾" - 1½"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

1 zero gap in
between
shear lug and
line stop

50
2 100

3
10 100
4

5
10 100 2 Gap 10 50
(typ) (typ)
= =

600

Clamps shall
be horizontal

100

Pipe Size Mark No 1 No Off Mark No 2 Area


(cm²)
Pipe Clip 5 Thk Stainless Steel
½" - 1½" No PC101 2 plate ASTM-A-240 50
Type 316 or equivalent

Mark No 3 Area Mark No 4 M.T.O. Mark No 5 Area


(cm²) Length (cm²)
10 thk 220 IPE 200 300 10 Thk 200
plate Plate

Assembly Tag No: - DA102 - X

Detail No Pipe Size


SUPPORT No DA102
SUPPORT TYPE Line stop for insulated Stainless Steel lines Sheet B29
PIPE SIZE ½" - 1½"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

10
(typ)

min
2

2 Gap
(typ)
12 dia bar, 400 long, (2 off)
Site trim to suit,
field weld to pipe clamp

Pipe Size Mark No 1 M.T.O. Mark No 2 No Off


Length
½" - 3" 12 dia 800 Pipe Clip 2
bar No PC1

Assembly Tag No: - DA201 - X


Detail No Pipe Size
SUPPORT No DA201
SUPPORT TYPE Line stop for non-insulated Galvanised lines Sheet B30
PIPE SIZE ½" - 3"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Clamps shall be at 45º


for pipes 3"
45o

100
2

100
1

3 100 2 Gap 10 100


(typ) (typ)
= =
500

Clamps shall be horizontal


for pipes ½" - 2"

Beam shall be cut


longitudinally to form Shoe

Pipe Size Mark No 1 M.T.O. Mark No 2 No Off Mark No 3 Area


Length (cm²)
½" - 3" IPE 200 250 Pipe Clip 2 10 Thk 200
No PC1 Plate

Assembly Tag No: - DA202 - X


Detail No Pipe Size

SUPPORT No DA202
SUPPORT TYPE Line stop for insulated Galvanised lines Sheet B31
PIPE SIZE ½" - 3"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
2 2 Trim to suit and
weld to existing
steel or vessel clip

130

L
Elevation
K

Alternative
connection
Existing Full to steel
10 encirclement Cradle (Elevation) 20
(typ) L

3 Gap θ°
(typ)
Field weld
A bracing where req'd
30° ≤ θ ≤ 60°

Plan A Bracing req'd when this


dimension > 300mm
Pipe Support No VG104
4-Directional Guide for Non-Insulated Pipes 4" - 24"

B A
3 Gap
75 (typ) 75 (typ)
(typ)

Note
A Bracing
omitted
B
for clarity
3 Gap
(typ)
Pipe Support No VG107
2-Directional Guide for Existing Cradle C101
Pipe Support No VG108
Non-Insulated Pipes 4" - 24" Refer to Iso for
2-Directional Guide for
orientation
Non-Insulated Pipes 4" - 24"
Assembly Tag No: - VG104 or VG107 or VG108 - X
Detail No Pipe Size
SUPPORT No VG104, VG107, VG108
SUPPORT TYPE Vertical Guides for Non-Insulated Stainless Steel Pipes Sheet B32
PIPE SIZE 4" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Pipe Pipe Mark Mark Maximum Horizontal


Size O.D. No 1 Length No 2 Length Loads (KN)
4 114 UPN 100 2000 1200
6 168 2000 1500
8 219 2500 1700 5.0
10 273 UPN 160 2500 1900
12 324 3000 2100
14 356 3000 UPN 100 2200
16 406 3300 2400 8.0
18 457 3300 2600
20 508 UPN 200 3800 2800
22 559 3800 3000 10.0
24 610 3800 3200

Pipe Pipe Dimensions


Size O.D. A B K L (Max)
4 114 140 264 1000 700
6 168 194 318 1000 700
8 219 245 369 1250 900
10 273 299 423 1250 900
12 324 350 474 1500 1100
14 356 382 506 1500 1100
16 406 432 556 1650 1200
18 457 483 607 1650 1200
20 508 534 658 1900 1400
22 559 585 709 1900 1400
24 610 636 760 1900 1400

SUPPORT No VG104, VG107, VG108


SUPPORT TYPE Vertical Guides for Non-Insul. Stainless Steel Pipes (dims) Sheet B33
PIPE SIZE 4" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

Cradle for Stainless lines only


See Note 1

250

Supporting sleeper
by others.
NOTE- The
100 2 Gap maximum sleeper
(typ) width is 600.

Pipe Mark No 1 Area Maximum Anchor


Size (cm²) Load (KN)
½-4 12 Thk 500 5.0
Plate

Notes 1- Cradle is mandatory for stainless steel lines 2" - 4". Refer to Support No C107
2- Cradles shall not be used for Carbon Steel lines

Assembly Tag No: - DA4 - X


Detail No Pipe Size
SUPPORT No DA4
SUPPORT TYPE Directional Anchor for Non-Insul. pipes on sleepers≤ 600mm Sheet B34
PIPE SIZE ½" - 4"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0
Cradle if required
Ref. Support No C7 or C107 1
See Note 1

175
H
250

Supporting sleeper
by others.
L 2 Gap NOTE- The
(typ) maximum sleeper
width is 600.

Pipe Size Maximum Anchor Load (KN)


No Cradle With Cradle
4 gap

6 - 14 15.0 40.0

10 10
2
= =

Pipe Size Mark No 1 Total Mark No 2 Area Dimensions


Length (cm²) A L H
6 1112 825 165 160 278
8 150 x 10 1136 10 Thk 1000 200 160 284
10 Plate 1152 Plate 1150 230 160 288
12 1192 1350 270 160 298
14 1224 1500 300 160 306

Notes 1- Cradle is mandatory for stainless steel lines. Refer to Support No C107

Assembly Tag No: - DA4 - X


Detail No Pipe Size
SUPPORT No DA4
SUPPORT TYPE Directional Anchor for Non-Insul. pipes on sleepers≤ 600mm Sheet B35
PIPE SIZE 6" - 14"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0
Cradle if required
Ref. Support
No C7 or C107
See Note 1
2

175
H 250

Supporting sleeper
by others.
NOTE- The
L 2 Gap
maximum sleeper
(typ) width is 600.

Pipe Maximum Anchor


Size Load (KN)
16 - 24 50.0
4 gap

26 - 40 100.0

1 10 10

= =

Pipe Size Mark No 1 Area Mark No 2 Area Dimensions


(cm²) (cm²) A L T H
16 2125 2002 250 200 10 278
18 10 Thk 274
20 Plate 284
22 2550 2023 300 200 10 281
24 278
26 10 Thk 287
28 2975 Plate 2613 350 250 12 284
30 282
32 12 Thk 291
34 Plate 288
36 3400 2631 400 250 12 286
38 284
40 282
Notes 1- Cradle is mandatory for stainless steel lines. Refer to Support No C107
Assembly Tag No: - DA4 - X
Detail No Pipe Size
SUPPORT No DA4
SUPPORT TYPE Directional Anchor for Non-Insul. pipes on sleepers≤ 600mm Sheet B36
PIPE SIZE 16" - 40"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

Cradle for Stainless


25 50 lines only
(typ) See Note 1

80 H
1

250

Supporting sleeper
3 by others.
2 Gap NOTE- The
(typ) maximum sleeper
width is 600.
900

NOTE - Lugs shall be tack welded to the shoe in the H = 100 for Support No DA5
shop. The final weld shall be made in the field. H = 150 for Support No DA6

Gusset plates
required on 3"
and 4" pipes
only Pipe Maximum Anchor
15 Size Load (KN)
(typ) ½-4 12.0
2

100

Pipe Mark No 1 Length Mark No 2 Area Mark No 3 Area


Size DA5 DA6 (cm²) (cm²)
½-2 IPE 200 450 900 HEA100 500
3-4 IPE 200 450 900 10 Thk Plate 100 HEA100 500

Notes 1- Cradle is mandatory for stainless steel lines 2" - 4". Refer to Support No C107
2- Cradles shall not be used for Carbon Steel lines

Assembly Tag No: - DA5, DA6 - X


Detail No Pipe Size
SUPPORT No DA5, DA6
SUPPORT TYPE Directional Anchor for Insul. pipes on sleepers≤ 600mm Sheet B37
PIPE SIZE ½" - 4"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0
Cradle if Cut
required 35 = = = = Notches
Ref. Support (typ) into
No C7 or C107. Anchor
Cradle is W 25
mandatory for
SS pipes

1 H
T

20
250

Supporting sleeper
by others.
3 NOTE- The
2 Gap maximum sleeper
(typ) width is 600.
L

NOTE - Lugs shall be tack welded to the shoe in the H = 100 for Support No DA5
shop. The final weld shall be made in the field. H = 150 for Support No DA6

Pipe Size Maximum Anchor Load (KN)


No Cradle With Cradle
6-8 25.0 100.0
10 - 24 50.0 200.0

Pipe Dimension
2
Size A L T W
6-8 150 900
10 200 900
12 250 1000 10
14 250 1000 10
16 300 1000
18 300 1100
30 20 - 22 350 1100 12
(typ) 24 400 1100
A
Pipe Dimension Mark No 1 DA5 DA6 Mark No 2 Area Mark No 3 Total
Size H Area (cm²) Area (cm²) (cm²) Length
6 1161 1611 1350
8 1161 1611 1350 HEA 100 500
10 1356 1806 10 Thk 1800
12 1641 2141 Plate 2500
14 (See 10 Thk 1641 2141 2500 HEA 160 500
16 Note 1) Plate 1836 2336 3000
18 1926 2476 3300
20 2121 2671 12 Thk 3850 HEA 200 500
22 2121 2671 Plate 3850
24 2316 2866 4400
Assembly Tag No: - DA5, DA6 - X
Detail No Pipe Size
SUPPORT No DA5, DA6
SUPPORT TYPE Directional Anchor for Insul. pipes on sleepers≤ 600mm Sheet B38
PIPE SIZE 6" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

Cradle for Stainless lines only


See Note 1

250

Supporting sleeper
by others.
NOTE- The
100 2 Gap maximum sleeper
(typ) width is 1000.

Pipe Mark No 1 Area Maximum Anchor


Size (cm²) Load (KN)
½-4 12 Thk 500 5.0
Plate

Notes 1- Cradle is mandatory for stainless steel lines 2" - 4". Refer to Support No C
108
2- Cradles shall not be used for Carbon Steel lines

Assembly Tag No: - DA7 - X


Detail No Pipe Size
SUPPORT No DA7
SUPPORT TYPE Directional Anchor for Non-Insul. pipes on sleepers > 600mm Sheet B39
PIPE SIZE ½" - 4"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0
Cradle if required
Ref. Support No C8 or C108 1
See Note 1

175
H
250

Supporting sleeper
by others.
L 2 Gap NOTE- The
(typ) maximum sleeper
width is 1000.

Pipe Size Maximum Anchor Load (KN)


No Cradle With Cradle
4 gap

6 - 14 15.0 40.0

10 10
2
= =

Pipe Size Mark No 1 Total Mark No 2 Area Dimensions


Length (cm²) A L H
6 1112 825 165 160 278
8 150 x 10 1136 10 Thk 1000 200 160 284
10 Plate 1152 Plate 1150 230 160 288
12 1192 1350 270 160 298
14 1224 1500 300 160 306

Notes 1- Cradle is mandatory for stainless steel lines. Refer to Support No C108

Assembly Tag No: - DA7 - X


Detail No Pipe Size
SUPPORT No DA7
SUPPORT TYPE Directional Anchor for Non-Insul. pipes on sleepers > 600mm Sheet B40
PIPE SIZE 6" - 14"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0
Cradle if required
Ref. Support
No C8 or C108
See Note 1
2

175
H 250

Supporting sleeper
by others.
NOTE- The
L 2 Gap
maximum sleeper
(typ) width is 1000.

Pipe Maximum Anchor


Size Load (KN)
16 - 24 50.0
4 gap

26 - 40 100.0

1 10 10

= =

Pipe Size Mark No 1 Area Mark No 2 Area Dimensions


(cm²) (cm²) A L T H
16 2125 2002 250 200 10 278
18 10 Thk 274
20 Plate 284
22 2550 2023 300 200 10 281
24 278
26 10 Thk 287
28 2975 Plate 2613 350 250 12 284
30 282
32 12 Thk 291
34 Plate 288
36 3400 2631 400 250 12 286
38 284
40 282
Notes 1- Cradle is mandatory for stainless steel lines. Refer to Support No C108
Assembly Tag No: - DA7 - X
Detail No Pipe Size
SUPPORT No DA7
SUPPORT TYPE Directional Anchor for Non-Insul. pipes on sleepers > 600mm Sheet B41
PIPE SIZE 16" - 40"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

Monolux Isolation Pipe Insulation


Block or equivalent.

60 Thk

150

150
Supporting steelwork
2 Gap by others
(typ)
= =
1
L

SECT Heat tubes

45o

250 Max

Pipe Dimension Mark No 1 Length


Size L
6 800 HEA 100 300
NOTE
1, For details of the SECT Traced Pipe Shoes refer to Specification No. 60-0000-L-SPE-1003.

Assembly Tag No: - DA8 - X


Detail No Pipe Size
SUPPORT No DA8
SUPPORT TYPE Directional Anchor for SECT Traced piping on steelwork Sheet B42
PIPE SIZE 6"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0
Monolux Isolation
Pipe Insulation
Block or equivalent.

60 Thk

150

250
Supporting sleeper by
others.
NOTE- The maximum
sleeper width is 500.
2 Gap
1 (typ)
= =

SECT Heat tubes 45o

250 Max

Pipe Dimension Mark No 1 Length


Size L
6 800 HEA 100 500
NOTE
1, For details of the SECT Traced Pipe Shoes refer to Specification No. 60-0000-L-SPE-1003.
Assembly Tag No: - DA9 - X
Detail No Pipe Size
SUPPORT No DA9
SUPPORT TYPE Directional Anchor for SECT Traced piping on sleepers Sheet B43
PIPE SIZE 6"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

Cradle for Stainless


25 50 lines only
(typ) See Note 1

80 100
1

250

Supporting sleeper
3 by others.
2 Gap NOTE- The
(typ) maximum sleeper
1300 width is 1000.

NOTE - Lugs shall be tack welded to the shoe in the


shop. The final weld shall be made in the field.

Gusset plates
required on 3"
and 4" pipes
only Pipe Maximum Anchor
15 Size Load (KN)
(typ) ½-4 12.0
2

100

Pipe Size Mark No 1 Length Mark No 2 Area (cm²) Mark No 3 Area (cm²)
½-2 IPE 200 650 HEA100 500
3-4 IPE 200 650 10 Thk Plate 100 HEA100 500

Notes 1- Cradle is mandatory for stainless steel lines 2" - 4". Refer to Support No C108
2- Cradles shall not be used for Carbon Steel lines

Assembly Tag No: - DA10 - X


Detail No Pipe Size
SUPPORT No DA10
SUPPORT TYPE Directional Anchor for Insul. pipes on sleepers > 600mm Sheet B44
PIPE SIZE ½" - 4"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0
Cradle if Cut
required 35 = = = = Notches
Ref. Support No (typ) into
C8 or C108. Anchor
Cradle is W 25
mandatory for
SS pipes

1 100
T

20
250

Supporting sleeper
by others.
3 NOTE- The
2 Gap maximum sleeper
(typ) width is 1000.
L

NOTE - Lugs shall be tack welded to the shoe in the


shop. The final weld shall be made in the field.

Pipe Size Maximum Anchor Load (KN)


No Cradle With Cradle
6-8 25.0 100.0
10 - 16 50.0 200.0

2
Pipe Dimension
Size A L T W
6-8 150 1300
10 200 1300
12 250 1400 10 10
14 250 1400
16 300 1400
30
(typ) A

Pipe Dimension Mark No 1 DA10 Mark No 2 Area Mark No 3 Total


Size H Area (cm²) (cm²) Length
6 1521 1950
8 1521 1950 HEA 100 500
10 (See 10 Thk 1716 10 Thk 2600
12 Note 1) Plate 2001 Plate 3500
14 2001 3500 HEA 160 500
16 2196 4200

Assembly Tag No: - DA10 - X


Detail No Pipe Size
SUPPORT No DA10
SUPPORT TYPE Directional Anchor for Insul. pipes on sleepers≤ 600mm Sheet B45
PIPE SIZE 6" - 16"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0
X Y Stiffening Ring, where required

= = =
25 Cut Notches
(typ) into Anchor

80
W H

T 75
75
C
Cradle is (typ) B 2 gap NOTE - Lugs shall
Mandatory (typ) be tack welded to
Ref Support L the shoe in the shop.
No C3 The final weld shall
be made in the field.

Stiffening Ring
6
Profile to Suit

θ 1
6
2

N = No of Gusset 4
Plates.
Gusset Plates
20 W 5
are to be evenly
spaced (typ)
D Pipe Maximum Anchor
Size Load (KN)
W
36 - 40 400.0
30 (typ)
(typ) = = Stiffening Ring Required for
A Pipe 36" and Above
For Pipe Specs
150H26 & 150K26

For other Pipe Specs


Assembly Tag No: -DA11 or DA12 - X refer to Support Nos DA2 & DA3
Detail No Pipe Size
SUPPORT No DA11, DA12
SUPPORT TYPE Directional Anchor for Spec Nos. 150H26 & 150K26 for In Sheet B46
PIPE SIZE 36" - 40"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 1

Support Pipe Dimension


Type Size H T W C B L D
DA11 36, 40 100 12 10 10 250 900 400
DA12 36, 40 150 12 10 10 250 900 400

Support Pipe Dimensions Angle No of


Type Size X Y θ (Deg) Gussets N
DA11,DA12 36, 40 12 80 30 0

Support Pipe Mark No 1 Area Mark No 2 Area Mark No 3 Area Dimension


Type Size (cm²) (cm²) (cm²) A
DA11 36 10 Thk 5735 10 Thk 2514 12 Thk 7823 869
40 Plate 6192 Plate 3017 Plate 8615 957
DA12 36 10 Thk 6635 10 Thk 2909 12 Thk 7823 869
40 Plate 7092 Plate 3456 Plate 8615 957

Support Pipe Mark No 4 Area Mark No 5 Area Mark No 6 Area


Type Size (cm²) (cm²) (cm²)
DA11,DA12 36 10 Thk 1800 10 Thk 1035 12 Thk 2298
DA11,DA12 40 Plate 1800 Plate 1035 Plate 2554

SUPPORT No DA11, DA12


SUPPORT TYPE Directional Anchor for Spec Nos. 150H26 & 150K26 (Dim Sheet B47
PIPE SIZE 36" - 40"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

= = =

W 25 Cut Notches
(typ)
into Anchor

80
H

T 125
125

Cradle is C (typ)
NOTE - Lugs shall
Mandatory B 2 gap (typ) be tack welded to
Ref Support
the shoe in the shop.
No C7 L
The final weld shall
be made in the field.

1
θ 6
2

3
N = No of Gusset
Plates.
4
Gusset Plates
are to be evenly
20 W 5
spaced
(typ)
D

W
30 (typ)
(typ) = =
A

Pipe Maximum Anchor


Size Load (KN)
26 - 40 400.0

Assembly Tag No: -DA5 or DA6 - X


Detail No Pipe Size
SUPPORT No DA5, DA6
SUPPORT TYPE Directional Anchor for Insulated Pipes on Sleepers ≤600 Sheet B48
PIPE SIZE 26" - 40"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

Support Pipe Dimension


Type Size H T W C B L D
DA5 26 - 40 100 12 10 10 250 1200 400
DA6 26 - 40 150 12 10 10 250 1200 400

Support Pipe Angle No of


Type Size θ (Deg) Gussets N
DA5,DA6 26 - 40 30 0

Support Pipe Mark No 1 Area Mark No 2 Area Mark No 3 Area Dimension


Type Size (cm²) (cm²) (cm²) A
26 6122 1452 7791 649
28 6427 1642 8319 693
30 6732 1843 8847 737
DA5 32 10 Thk 7037 10 Thk 2056 12 Thk 9374 781
34 Plate 7342 Plate 2280 Plate 9902 825
36 7646 2514 10430 869
38 7951 2760 10958 913
40 8256 3017 11486 957
26 5492 1737 7791 649
28 5720 1949 8319 693
30 5949 2172 8847 737
DA6 32 10 Thk 6178 10 Thk 2407 12 Thk 9374 781
34 Plate 6406 Plate 2652 Plate 9902 825
36 6635 2909 10430 869
38 6863 3177 10958 913
40 7092 3456 11486 957

Support Pipe Mark No 4 Area Mark No 5 Area


Type Size (Plate) (cm²) (Plate) (cm²)
DA5,DA6 26 - 40 10 Thk 3000 10 Thk 1725

SUPPORT No DA5, DA6


SUPPORT TYPE Directional Anchor for Insulated Pipes on Sleepers (Dims Sheet B49
PIPE SIZE 26" - 40"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

Gusset plates
required on 3"
and 4" pipes
only

25

60 90 100 15
1
(typ)
2 100

3
150 Do not weld
this side of 10
50 2 Gap 100
Shear lug
(typ) (typ)
= = 80

600 100

4
NOTE - Lugs shall be tack welded to the
shoe in the shop. The final weld shall be Isolation Pad. Site
made in the field. trim pad if it overlaps
the steelwork

Pipe Maximum Anchor


Size Load (KN)
½-4 12.0

Pipe Size Mark No 1 Length Mark No 2 Area (cm²) Mark No 3 Area (cm²) Mark No 4
½-2 IPE 200 300 10 Thk 200 Fabreeka Nitrile 21
3-4 IPE 200 300 10 Thk Plt 200 Plate 200 Ply Pad 150 x 80
or equivalent

Assembly Tag No: -DA13 - X Dimensions Required: - None


Detail No Pipe Size
SUPPORT No DA13
SUPPORT TYPE Directional Anchor for Acoustically Insulated Pipes Sheet B50
PIPE SIZE ½" - 4"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0
Cradle if Cut
required 35 = = = = Notches
Ref. Support (typ) into
No C3 or C103. Anchor
Cradle is 10 25
mandatory for
SS pipes

1 90 100
T

20 150
3
150
Do not weld 2 Gap
this side of (typ)
Shear lug (typ) L

NOTE - Lugs shall be tack welded to the


Isolation Pad. Site trim pad
4 shoe in the shop. The final weld shall be
if it overlaps the steelwork
made in the field.
Pipe Size Maximum Anchor Load (KN)
No Cradle With Cradle
6-8 25.0 100.0
10 - 24 50.0 200.0

Pipe Dimension
2
Size A L T B
30 6-8 150 600 100
(typ) 10 200 600 150
12 250 700 10 200
14 250 700 200
16 300 700 250
18 300 800 250
B 20 - 22 350 800 12 300
24 400 800 350
A
Pipe Mark No 1 Area Mark No 2 Area Mark No 3 Total Mark No 4 Size
Size (cm²) (cm²) Length
6 891 900 150 x 100
8 891 900 HEA 100 300 150 x 100
10 1086 10 Thk 1200 Fabreeka 150 x 150
12 1371 Plate 1750 Nitrile 21 200 x 150
14 10 Thk 1371 1750 HEA 160 300 Ply Pad 200 x 150
16 Plate 1566 2100 or 250 x 150
18 1656 2400 equivalent 250 x 150
20 1851 12 Thk 2800 HEA 200 300 300 x 150
22 1851 Plate 2800 300 x 150
24 2046 3200 350 x 150
Assembly Tag No: -DA13 - X
Detail No Pipe Size
SUPPORT No DA13
SUPPORT TYPE Directional Anchor for Acoustically Insulated Pipes Sheet B51
PIPE SIZE 6" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

= = =
25 Cut Notches
(typ)
into Anchor

70 90
W 100

T 75
75
150
C
Cradle is (typ) B 2 gap NOTE - Lugs shall
Mandatory (typ) be tack welded to
Ref Support L the shoe in the
No C3 shop. The final weld
shall be made in the
field.

6
1 Isolation Pad. Site trim pad
θ if it overlaps the steelwork
6
2
E
3

20 W 5
(typ)
D

W
30 (typ)
(typ) = =
A

Assembly Tag No: -DA13 - X


Detail No Pipe Size
SUPPORT No DA13
SUPPORT TYPE Directional Anchor for Acoustically Insulated Pipes Sheet B52
PIPE SIZE 26" - 40"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

Support Pipe Dimension


Type Size H T W C B L D
DA13 26 - 40 100 12 10 10 250 900 400

Support Pipe Angle


Type Size θ (Deg)
DA13 26 - 40 30

Support Pipe Mark No 1 Area Mark No 2 Area


Type Size (cm²) (cm²)
26 4592 1452
28 4820 1642
30 5049 1843
DA13 32 10 Thk 5278 10 Thk 2056
34 Plate 5506 Plate 2280
36 5735 2514
38 5963 2760
40 6192 3017

Support Pipe Mark No 3 Area Dimension Mark No 6 Size Dimension


Type Size (cm²) A E
26 5843 649 500 x 150 500
28 6239 693 Fabreeka 500 x 150 500
30 6635 737 Nitrile 21 550 x 150 550
DA13 32 12 Thk 7031 781 Ply Pad 600 x 150 600
34 Plate 7427 825 or 650 x 150 650
36 7823 869 equivalent 700 x 150 700
38 8219 913 750 x 150 750
40 8615 957 800 x 150 800

Support Pipe Mark No 4 Area Mark No 5 Area


Type Size (cm²) (cm²)
DA13 26 - 40 10 Thk 1800 10 Thk 1035
Plate Plate

SUPPORT No DA13
SUPPORT TYPE Directional Anchor for Acoustically Insulated Pipes (Dims Sheet B53
PIPE SIZE 26" - 40"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

Ref Cradle, Support No


C-101, C-102 or C-103 1

75

4 gap
H
150

10 10
L 2 gap
2
(typ) = =

Pipe Size Maximum Anchor


Load (KN)
8 - 14 40.0

Pipe Size Mark No 1 Total Mark No 2 Area Dimensions


Length (cm²) A L H
8 150 x 10 736 10 Thk 600 200 160 184
10 Stainless 752 Stainless 690 230 160 188
12 Steel Plate 792 Steel Plate 810 270 160 198
14 ASTM-A-240 824 ASTM-A-240 900 300 160 206
Type 316 Type 316

Assembly Tag No: - DA103 - X


Detail No Pipe Size
SUPPORT No DA103
Directional Anchor for Non-Insulated or PPC piping
SUPPORT TYPE Sheet B54
with a design temp of -60°C or below
PIPE SIZE 8" - 14"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

Ref Cradle, Support No


C-101, C-102 or C-103

75 H

4 gap
150
1
10 10
2 T T 2 gap
1
(typ) = =

L A

Pipe Maximum Anchor


Size Load (KN)
16 - 24 50.0

Pipe Size Mark No 1 Area Mark No 2 Area Dimensions


(cm²) (cm²) A L T H
16 10 Thk 1125 10 Thk 1200 250 200 10 178
18 Stainless Stainless 174
20 Steel Plate Steel Plate 184
22 ASTM-A-240 1350 ASTM-A-240 1200 300 200 10 181
24 Type 316 Type 316 178

Assembly Tag No: - DA103 - X


Detail No Pipe Size
SUPPORT No DA103
Directional Anchor for Non-Insulated or PPC piping
SUPPORT TYPE Sheet B55
with a design temp of -60°C or below
PIPE SIZE 16" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

Monolux Isolation Pipe Insulation


Block or equivalent.

60 Thk

150

SECT Heat tubes

45o

NOTE
1, For details of the SECT Traced Pipe Shoes refer to Specification No. 60-0000-L-SPE-1003.
2, Support shall be used with Anchor Lugs DA8

Assembly Tag No: - SAS1 - X


Detail No Pipe Size
SUPPORT No SAS1
SUPPORT TYPE Anchor Shoe for SECT Traced piping on steelwork Sheet B56
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

Monolux Isolation
Pipe Insulation
Block or equivalent.

60 Thk

150

Supporting sleeper by
others.
NOTE- The maximum
sleeper width is 500.

SECT Heat tubes 45o

NOTE
1, For details of the SECT Traced Pipe Shoes refer to Specification No. 60-0000-L-SPE-1003.
2, Support shall be used with Anchor Lugs DA9

Assembly Tag No: - SAS2 - X


Detail No Pipe Size
SUPPORT No SAS2
SUPPORT TYPE Anchor Shoe for SECT Traced piping on Sleepers Sheet B57
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3
6mm Weep Hole For Trunnion
seal with mastic Details Refer
after welding to Iso.
X
1

The Elevation
X of the trunnion
View X-X
shall allow for Round Plate
12mm Field
750 250 Shim.
(Max)

NOTES
1- Unless otherwise advised by Piping Stress the Trunnion sizes
that shall be used are listed below

Pipe Size 2", 3" 4" 6" 8" 10"


Trunnion Size 2" 3" 4" 6" 8"

Pipe Size 12", 14" 16", 18" 20" - 24" 26" - 30" 32" - 36"
Trunnion Size 10" 12" 16" 20" 24"

Trunnion Mark No 1 Dimension


2
Size Description Area (cm ) A
2 100 100
3 144 120
4 6 Thk 225 150
6 Round 400 200
8 Plate 625 250
10 961 310
12 1296 360
16 10 Thk 2025 450
20 Round 3025 550
24 Plate 4225 650
26 4900 700

Assembly Tag No: - T1 - X Dimensions Required: - None


Detail No Trunnion Size
SUPPORT No T1
SUPPORT TYPE Horizontal Trunnion Support from Pipe (1 Off) Sheet C1
PIPE SIZE 2" - 36"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

For Trunnion
Details Refer
to Iso.
1
View X-X Round Plate
X

A A

X 1
The Elevation
6mm Weep Hole of the trunnion
seal with mastic shall allow for
after welding (Typ) 750 250 12mm Field
(Max) Shim.

NOTES
1- Unless otherwise advised by Piping Stress the Trunnion sizes
that shall be used are listed below

Pipe Size 2", 3" 4" 6" 8" 10"


Trunnion Size 2" 3" 4" 6" 8"

Pipe Size 12", 14" 16", 18" 20" - 24" 26" - 30" 32" - 36"
Trunnion Size 10" 12" 16" 20" 24"

Trunnion Mark No 1 Dimension


2
Size Description Area (cm ) A
2 200 100
3 288 120
4 6 Thk 450 150
6 Round 800 200
8 Plate 1250 250
10 1922 310
12 2592 360
16 10 Thk 4050 450
20 Round 6050 550
24 Plate 8450 650

Assembly Tag No: - T2 - X Dimensions Required: - None


Detail No Trunnion Size
SUPPORT No T2
SUPPORT TYPE Horizontal Trunnion Support from Pipe (2 Off) Sheet C2
PIPE SIZE 2" - 36"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
Pad if required.
Ref Spec No Temperature Correction Factor
60-0000-L-SPE-0014 Material Carbon Steel Stain. Steel
Grade A333 Gr 8 A671 CC 60 A312 TP316/L
Pipe Size 2" - 16" 18" - 36" 2" - 36"
50 1.00 1.00 1.00
100 1.00 0.97 1.00

Temperature °C
150 1.00 0.94 1.00
200 1.00 0.92 0.96
250 0.95 0.88 0.91
300 0.89 0.81 0.86
350 0.83 0.76 0.83
400 0.65 0.65 0.81
D (m)
Load (N) Bending Moment = D x Load

Allowable Bending Moment (Nm)


Pipe Trun Corrosion Allowance = 1.5mm Corrosion Allowance = 3.0mm
Size Size Sch 20 Sch 40 Sch 80 Sch 20 Sch 40 Sch 80
(") (") No Pad Pad No Pad Pad No Pad Pad No Pad Pad No Pad Pad No Pad Pad
2 2 163 375 13 119
3 2 303 1317 593 2309 93 760 271 1462
4 3 708 2963 1419 5371 248 1732 691 3422
6 4 1352 5365 3039 10978 566 3253 1661 7214
8 6 3371 12895 7466 26404 1559 7971 4250 17465
10 8 6466 24073 15229 52753 3222 15207 9088 35470
12 10 11183 40821 27751 94737 5839 26081 17019 64145
14 10 12236 44105 30568 103570 6400 27635 18489 68473
16 12 8621 33232 20305 71806 48854 164023 3753 19652 11132 45742 30141 109305
18 12 8128 31332 23390 81530 54643 182147 3539 18528 13271 52591 34232 122142
20 16 17124 63423 38411 133052 95079 315113 8347 38819 22110 86293 60293 212371
22 16 16327 60471 40000 137797 104368 344225 7959 37012 23316 89798 66855 232973
24 16 15632 57897 44871 153170 113366 372416 7620 35437 26697 100610 73218 252930
26 20 39181 138561 21480 88265
28 20 37756 133521 20699 85054
30 20 36475 128993 19997 82170
32 24 50857 179852 87433 298461 27881 114568 52020 196045
34 24 49338 174482 84822 289550 27049 111147 50467 190191
36 24 47948 169566 95048 322042 26287 108016 57490 212910

Notes 1- The loads shown are for one trunnion. When two trunnions are used the actual piping load
shall be divided by two.
2- The table is for carbon steel & stainless steel pipes up to 50°C. For higher temperatures
the allowable loads shall be multiplied by the temperature correction factor (see above table).
3- For pipe schedules not listed the allowable load = tabulated load xp1.5
t /tt1.5
Where tp is the thickness of the pipe in question less mill tolerance and corrosion allowance
and, tt is the thickness of the tabulated pipe less mill tolerance and corrosion allowance

SUPPORT No T1, T2
SUPPORT TYPE Horizontal Trunnion Allowable Loads Sheet C3
PIPE SIZE 2" - 36"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

For Trunnion
Details Refer View X-X Round Plate
to Iso.
1

6mm Weep
Hole seal with
mastic after 250 1000
welding
(Max)
NOTES
1- For allowable loads see Sheet C17

2- Unless otherwise advised by Piping Stress the Trunnion sizes


that shall be used are listed below
Pipe Size 2", 3" 4" 6" 8" 10"
Trunnion Size 2" 3" 4" 6" 8"

Pipe Size 12", 14" 16", 18" 20" - 24" 26" - 30" 32" - 36"
Trunnion Size 10" 12" 16" 20" 24"

Trunnion Mark No 1 Dimension Trunnion Mark No 1 Dimension


2 2
Size Description Area (cm ) A Size Description Area (cm ) A
2 100 100 10 6 Thk 961 310
3 6 Thk 144 120 12 Rnd. Plate 1296 360
4 Round 225 150 16 10 Thk 2025 450
6 Plate 400 200 20 Round 3025 550
8 625 250 24 Plate 4225 650

Assembly Tag No: - T3 - X Dimensions Required: - None


Detail No Trunnion Size
SUPPORT No T3
SUPPORT TYPE Horizontal Trunnion Support from Elbow Sheet C4
PIPE SIZE 2" - 36"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 4
NOTE: - This support shall not be
For Trunnion used from grade in un-paved areas.
Details Refer Ref Support No BS4
to Iso. Field Weld
Detail A
Trunnion Size
2" - 16"
Minimum Gap

2
Field Weld
A

For bottom of
Trunnion EL
see Table 1.6 ± 55°
350
below 350 0.8mm
Site
Trim
to suit
20 Detail B
1 10
weep Trunnion Size
2 A 2 1 18" to 24"
hole

Unless advised by Piping Stress the Trunnion sizes that shall be used are listed below: -
Pipe Size 2", 3" 4" 6" 8", 10" 12", 14"
Trunnion Size 2" 3" 4" 6" 8"
Pipe Size 16", 18" 20", 22" 24" - 26" 30" - 34" 36" - 40"
Trunnion Size 10" 12" 16" 20" 24"
Support at Grade Support on Steelwork
Trunnion Size (") 2 - 12 16 - 24 All
Pipe Support Foundation or Baseplate BP1 F8 or F9 BPS Where req'd
Bottom of Trunnion elevation 100150 100350 TOS + 150
Trunnion Dimension Mark No 1 Total Mark No 2 Area
Size A Length (cm2)
2 150 3" Sch XS Pipe 450
3 180 4" Sch XS Pipe 330 10 Thk 648
4 230 6" Sch 40 Pipe Square 1058
6 290 8" Sch 40 Pipe Plate 1682
8 320 10" Sch 40 Pipe 2048
10 350 12" Std Pipe 326 12 Thk 2450
12 380 14" Std Pipe Square 2888
16 500 18" Sch 40 Pipe Plate 5000
18 530 18" Sch 40 Pipe 2809
20 560 20" Sch Std Pipe 335 15 Thk 3136
24 650 24" Sch Std Pipe Sqr Plate 4225
Assembly Tag No: - BS1 - X
Detail No Trunnion Size
SUPPORT No BS1
SUPPORT TYPE Non-Adjustable Base Support Sheet C5
PIPE SIZE 2" - 40"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

For Trunnion
Details Refer
to Iso.

View X-X
1 X X
3 Hole
Dia D
Installation 10
H
Height

B
2 (typ) = =
3
A
Grind smooth
after welding

NOTE: -This support, when located at grade, shall be used in conjunction with
Pipe Support foundations F8 or F9, to ensure a consistent elevation.

Unless otherwise advised by Piping Stress the Trunnion sizes that shall be used are listed below
Pipe Size 2", 3" 4" 6" 8", 10" 12", 14"
Trunnion Size 2" 3" 4" 6" 8"

Pipe Size 16", 18" 20", 22" 24" - 26" 30" - 34" 36" - 40"
Trunnion Size 10" 12" 16" 20" 24"

Assembly Tag No: - BS2 - X


Detail No Trunnion Size
SUPPORT No BS2
SUPPORT TYPE Adjustable Base Support Sheet C6
PIPE SIZE 2" - 40"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Trunnion Mark No 1 Mark No 2 Mark No 3 Area


Size (8 Off) (4 Off) (cm2)
2 M20 Hex Nut M20 Stud Bolt 800
3 Heavy Type 150 Long 800
4 M24 Hex Nut M24 Stud Bolt 12 Thk Plate 1352
6 Heavy Type 150 Long 1682
8 2048
10 M30 Hex Nut M30 Stud Bolt 15 Thk Plate 2450
12 Heavy Type 200 Long 2888
16 5000
20 M36 Hex Nut M36 Stud Bolt 20 Thk Plate 6272
24 Heavy Type 200 Long 8450

Trunnion Dimensions
Size A B D H
2 200
3 200 30 22
4 260 100
6 290 26
8 320
10 350 45
12 380 32
16 500 130
20 560
24 650 55 38

SUPPORT No BS2
SUPPORT TYPE Adjustable Base Support (Dimensions) Sheet C7
PIPE SIZE 2" - 40"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

For Trunnion
Details Refer
to Iso.

Existing Trunnion
Support (BS1) or 1
Adjustable Trunnion
Support (BS2).
2

17 5
Symmetrically weld
5mm Thick square
= = S.S. Plate to underside
of Trunnion Support.
A

Note: - For PTFE details and installation instructions refer to Spec No 60-0000-L-SPE-1003

Trunnion Mark No 1 Area Mark No 2 No Off Dimension


Size (cm²) A
2-4 5 Thk Polished Stainless Steel 169 PTFE pad Type A 1 130
6-8 Plate ASTM-A-240 Type 316 400 PTFE pad Type B 1 200
10 - 12 or Equivalent. 900 PTFE pad Type D 1 300

Assembly Tag No: - BS3 - X


Detail No Trunnion Size
SUPPORT No BS3
SUPPORT TYPE PTFE for Existing Base Support Sheet C8
PIPE SIZE 2" - 22"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

For Trunnion
Details Refer
to Iso.
2 View X-X

Existing Trunnion
Support (BS1) or
Adjustable Trunnion
Support (BS2). 1 B
B
17 5

X = = X
B B
A

Note: - For PTFE details and installation instructions refer to Spec No 60-0000-L-SPE-1003

Trunnion Mark No 1 Area Mark No 2 No Off Dimension


Size (cm²) A B
16 5 Thk Polished Stainless Steel 1600 4 400 100
20 Square Plate ASTM-A-240 2025 PTFE pad 4 450 125
24 Type 316 or Equivalent. 2500 Type B 4 500 150

Assembly Tag No: - BS3 - X


Detail No Trunnion Size
SUPPORT No BS3
SUPPORT TYPE PTFE for Existing Base Support Sheet C9
PIPE SIZE 24" - 40"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Ref BS1

X X
1

100

Weld Angles to 2 Gap


Existing Base- Do not weld this
(Typ)
Plate face of the guide

=
View X-X

Trunnion Mark No1 Total


Size (4 Off) Length
2-6 60 x 6 Angle 400
8 - 12 100 x 10 Angle 400
16,20,24 HEA 100 400

Assembly Tag No: - BA1 - X


Detail No Trunnion Size
SUPPORT No BA1
SUPPORT TYPE Base Anchor for Non-Adjustable Support Sheet C10
PIPE SIZE 2" - 40"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

For Trunnion
Details Refer
to Iso.
Ref BS2
X X
1

2 Gap
Do not weld this
(Typ)
face of the guide

View X-X

Trunnion Dimension Mark No1 Total


Size H (4 Off) Length
2-6 150 60 x 6 Angle 600
8 - 12 180 100 x 10 Angle 720
16,20,24 180 HEA 100 720

Assembly Tag No: - BA2 - X


Detail No Trunnion Size
SUPPORT No BA2
SUPPORT TYPE Base Anchor for Adjustable Support Sheet C11
PIPE SIZE 2" - 40"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3

Ref BS1

X X
1

100

Do not weld this


Weld Angles to 2 Gap
face of the guide
Existing Base- (Typ)
Plate

For Correct Orientation


of Guides Refer to =
View X-X
the Isometric

Trunnion Mark No1 Total


Size (2 Off) Length
2-6 60 x 6 Angle 200
8 - 12 100 x 10 Angle 200
16,20,24 HEA 100 200

Assembly Tag No: - BG1 - X


Detail No Trunnion Size
SUPPORT No BG1
SUPPORT TYPE Base Guide for Non-Adjustable Support Sheet C12
PIPE SIZE 2" - 40"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3

For Trunnion
Details Refer Ref BS2
to Iso.

X X
1

2 Gap Do not weld this


(Typ) face of the guide

For Correct Orientation


of Guides Refer to the
Isometric =

View X-X

Trunnion Mark No1 Total Dimension


Size (2 Off) Length H
2-6 60 x 6 Angle 300 150
8 - 12 100 x 10 Angle 360 180
16,20,24 HEA 100 360 180

Assembly Tag No: - BG2 - X


Detail No Trunnion Size
SUPPORT No BG2
SUPPORT TYPE Base Guide for Adjustable Support Sheet C13
PIPE SIZE 2" - 40"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3

For Details of
Trunnion Refer Existing Trunnion
to Iso Support

3
NOTE 1 1
X X
6

25 (Min) Grout
150 Type G1
2
100 Bolt
Penetration
200
Existing
Paving
NOTE 1 4

50
(Typ)
Hole
A
Dia = D
View X-X

NOTES 1- Refer to Section 10 of this Spec for a procedure for the installation of bolts,
grouting and monitoring the settlement of the paving
2- For General Notes refer to Drawing Nos. 60-0000-Q-STD-0010-01 and 02
3- Hilti HIT-ICE resin to be used if the installation temperature is below -5°C)
Trunnion Mark No 1 (Note 3) Mark No 2 Area (cm²) Mark No 3 Dimension
Size (4 Off) (8 Off) A D
2-3 M20 threaded rod with Hilti HY150 20 Thk 1764 M20 Nuts 420 22
resin capsule adhesive 280 Long Plate
4-6 M30 threaded rod with Hilti HY150 20 Thk 3025 M30 Nuts 550 33
resin capsule adhesive 280 Long Plate

Trunnion Mark No 5 Mark No 6 Max Loads (KN)


Size (8 Off) Trunnion 200 Thick Paving
2-3 Cementitious Grout M20 Washers Size Vertical Shear
4-6 (G1) 0.01m3 M30 Washers 2-3 20.0 6.0
4-6 25.0 12.0
Assembly Tag No: - BP - X
Detail No Trunnion Size
SUPPORT No BP
SUPPORT TYPE Base Plate from grade Sheet C14
PIPE SIZE 2" - 10"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 4
NOTE: - This support shall
For Trunnion only be used from grade
Details Refer in un-paved areas.
to Iso. For other locations refer
to BS1
Field Weld
Detail A
Trunnion Size
2 2" - 16"
Minimum Gap
A

1
For bottom of Field Weld
Trunnion EL weep
100275 hole
150 2

1.6 ± 55°
U/S baseplate
20 0.8mm
EL 100200 350
10
Site
20 A Trim
to suit
Detail B
3 Trunnion Size
2 1 18" to 24"

Unless advised by Piping Stress the Trunnion sizes that shall be used are listed below: -
Pipe Size 2", 3" 4" 6" 8", 10" 12", 14"
Trunnion Size 2" 3" 4" 6" 8"
Pipe Size 16", 18" 20", 22" 24" - 26" 30" - 34" 36" - 40"
Trunnion Size 10" 12" 16" 20" 24"

Trunnion Dimension Mark No 1 Total Area Mark No 2 Area Mark


2 2
Size A Length (cm ) (cm ) No 3
2 150 3" Sch XS Pipe 450 Pipe
3 180 4" Sch XS Pipe 130 10 Thk 648 Support
4 230 6" Sch 40 Pipe Square 1058 Foundat'n
6 290 8" Sch 40 Pipe Plate 1682 F9-4
8 320 10" Sch 40 Pipe 2048
10 350 12" Std Pipe 126 12 Thk 2450 Pipe
12 380 14" Std Pipe Square 2888 Support
16 500 18" Sch 40 Pipe Plate 5000 Foundat'n
18 530 18" Sch 40 Pipe 2000 2809 F9-4
20 560 20" Sch Std Pipe 2400 15 Thk 3136
24 650 24" Sch Std Pipe 2900 Sqr Plate 4225
Assembly Tag No: - BS4 - X
Detail No Trunnion Size
SUPPORT No BS4
SUPPORT TYPE Non-Adjustable Base Support for un-paved areas Sheet C15
PIPE SIZE 2" - 40"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

For Details of
Trunnion Refer Existing Trunnion
to Iso Support

X X

Field weld plate to


existing steelwork

View X-X

Trunnion Mark No 1 Area (cm²) Dimension


Size A
2-3 10 Thk 1764 420
4-6 Plate 3025 550
8 - 12 12 Thk 4900 700
Plate

NOTE: - The allowable loads are limited by the supporting steelwork

Assembly Tag No: - BPS - X


Detail No Trunnion Size
SUPPORT No BPS
SUPPORT TYPE Base Plate from Steelwork Sheet C16
PIPE SIZE 2" - 22"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Temperature Correction Factor


Carbon Steel St. Steel
Material Grade A333 A671 A312
Gr 8 CC 60 TP316/L
Pipe Size 2" - 16" 18" - 36" 2" - 36"
50 1.00 1.00 1.00
100 1.00 0.97 1.00

Temperature °C
150 1.00 0.94 1.00
200 1.00 0.92 0.96
250 0.95 0.88 0.91
300 0.89 0.81 0.86
Load
D (m) 350 0.83 0.76 0.83
(N)
400 0.65 0.65 0.81

Bending Moment = D x Load

Pipe Trun Allowable Bending Moment (Nm)


Size Size c.a. = 1.5mm c.a. = 3.0mm
(") (") Sch 20 Sch 40 Sch 80 Sch 20 Sch 40 Sch 80
2 2 163 375 13 119
3 2 303 593 93 271
4 3 708 1419 248 691
6 4 1352 3039 566 1661
8 6 3371 7466 1559 4250
10 8 6466 15229 3222 9088
12 10 11183 27751 5839 17019
14 10 12236 30568 6400 18489
16 12 8621 20305 48854 3753 11132 30141
18 12 8128 23390 54643 3539 13271 34232
20 16 17124 38411 95079 8347 22110 60293
22 16 16327 40000 104368 7959 23316 66855
24 16 15632 44871 113366 7620 26697 73218
26 20 39181 21480
28 20 37756 20699
30 20 36475 19997
32 24 50857 87433 27881 52020
34 24 49338 84822 27049 50467
36 24 47948 95048 26287 57490

Notes 1- The table is for carbon steel & stainless steel pipes up to 50°C. For higher temperatures
the allowable loads shall be multiplied by the temperature correction factor (see above table).
2- For pipe schedules not listed the allowable load = tabulated load xp1.5
t /tt1.5
Where tp is the thickness of the pipe in question less mill tolerance and corrosion allowance
and, tt is the thickness of the tabulated pipe less mill tolerance and corrosion allowance

SUPPORT No T3
SUPPORT TYPE Allowable Loads for Horizontal Trunnion from Elbows Sheet C17
PIPE SIZE 2" - 36"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 4

NOTE: - This support shall be used in


paved areas from plinths & in non-paved
areas from spread-footing foundations Nos
F9-6 to F9-10

Field Weld

For Trunnion Detail A


Details Refer Trunnion Size
to Iso. 2" - 16"
Minimum Gap
A
2
Field Weld
For bottom of
Trunnion EL
100275
150 weep
1 hole
2 20 1.6 ± 55°
0.8mm
U/S baseplate 350
EL 100200 Site
20 10 Trim
to suit
A Detail B
Paving
Trunnion Size
or grade
2 1 18" to 24"

Pipe Support Foundation


Ref. Foundation F9-6 to F9-10 or 3 F8N3-XX.Where XX is
Civil designed foundation trunnion size

Unless advised by Piping Stress the Trunnion sizes that shall be used are listed below: -
Pipe Size 2", 3" 4" 6" 8", 10" 12", 14"
Trunnion Size 2" 3" 4" 6" 8"
Pipe Size 16", 18" 20", 22" 24" - 26" 30" - 34" 36" - 40"
Trunnion Size 10" 12" 16" 20" 24"

Trunnion Dimension Mark No 1 Total Area Mark No 2 Area Mark No 3


Size A Length (cm 2) (cm 2)
2 150 3" Sch XS Pipe 450 F8N3-2
3 180 4" Sch XS Pipe 130 10 Thk 648 F8N3-3
4 230 6" Sch 40 Pipe Square 1058 F8N3-4
6 290 8" Sch 40 Pipe Plate 1682 F8N3-6
8 320 10" Sch 40 Pipe 2048 F8N3-8
10 350 12" Sch Std Pipe 126 12 Thk 2450 F8N3-10
12 380 14" Std Pipe Square 2888 F8N3-12
16 500 18" Std Pipe Plate 5000 F8N3-16
20 560 20" Sch Std Pipe 2400 15 Thk 3136 F8N3-20
24 650 24" Sch Std Pipe 2900 Sqr Plate 4225 F8N3-24
Assembly Tag No: - BS5 - X
Detail No Trunnion Size
SUPPORT No BS5
SUPPORT TYPE Non-Adjustable Base Support for paved areas and
Sheet C18
non-paved areas from spread-footing type foundations
PIPE SIZE 2" - 40"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 4

Detail A
For Trunnion Trunnion Size
Details Refer 2" - 16"
to Iso.
Field Weld

Minimum Gap
2 A
Field Weld

Trunnion EL
TOS + 75 weep
hole
150 1.6 ± 55°
0.8mm
350
20 Site
1 10 Trim
A to suit
2 Detail B
Trunnion Size
2 1 18" to 24"

Unless advised by Piping Stress the Trunnion sizes that shall be used are listed below: -

Pipe Size 2", 3" 4" 6" 8", 10" 12", 14"
Trunnion Size 2" 3" 4" 6" 8"
Pipe Size 16", 18" 20", 22" 24" - 26" 30" - 34" 36" - 40"
Trunnion Size 10" 12" 16" 20" 24"

Trunnion Dimension Mark No 1 Total Area Mark No 2 Area


Size A Length (cm 2) (cm 2)
2 150 3" Sch XS Pipe 450
3 180 4" Sch XS Pipe 130 10 Thk 648
4 230 6" Sch 40 Pipe Square 1058
6 290 8" Sch 40 Pipe Plate 1682
8 320 10" Sch 40 Pipe 2048
10 350 12" Std Pipe 126 12 Thk 2450
12 380 14" Std Pipe Square 2888
16 500 18" Sch 40 Pipe Plate 5000
18 530 18" Sch 40 Pipe 1950 2809
20 560 20" Sch Std Pipe 2400 15 Thk 3136
24 650 24" Sch Std Pipe 2900 Sqr Plate 4225

Assembly Tag No: - BS6 - X


Detail No Trunnion Size
SUPPORT No BS6
SUPPORT TYPE Small Non-Adjustable Base Support from existing steel Sheet C19
PIPE SIZE 2" - 40"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 1

Full encirclement pad, shall be


Trunnion. supplied to site in at least 2 pieces
Spec shall
2
be the same
as the pipe

1
View X-X Round Plate
X

B
A A

X 1
The Elevation
6mm Weep Hole of the trunnion
seal with mastic shall allow for
250
after welding (Typ). 12mm Field
1 weephole is L Shim.
required per section
of encirclement pad

NOTE - 1- For welding details of the trunnion refer to Standard Piping Detail No 19 in
Spec No 60-0000-L-SPE-0014
2- The trunnion shall be welded to the pipe before welding the reinforcing cradle
3- Both welds shall be completed in the field

Pipe Pipe Trunnion


Size Spec Size Pipe Trunnion Dimension
48 150K26 30 Size Size A B
54 150H26 30 48",54",60" 30" 790 1525
60 150K26 30 66",70" 36" 940 1830
66 150H26 36
70 150K26 36

Pipe Mark No 1 Mark No 2 Dimension


2 2
Size Description Area (cm ) Description Area (cm )
48 12482 59377 1525
54 10 Thk 12482 10 Thk 66679 1525
60 Round 12482 Plate 73982 1525
66 Plate 17672 97541 1830
70 17672 103382 1830
Assembly Tag No: - T2 - X Dimensions Required: - None
Detail No Trunnion Size
SUPPORT No T2
SUPPORT TYPE Horizontal Trunnion Support from Pipe (2 Off) Sheet C20
PIPE SIZE 48" - 70"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

3
H

4 2

5
1

Supt. No HR1 (Light Loads) Supt. No HR3 (Light Loads)


Supt. No HR2 (Heavy Loads)

HR1 HR2 HR3


Pipe Max Max Max Dimension H
Size Load (KN) Load (KN) Load (KN) Maximum Minimum
½ - 1½ 400
2 4.0 4.0
3 12.0 2000 500
4
6-8 7.0 600
10 7.0 20.0 800
12 2200
14 - 18 12.0 35.0 900
20 - 24 2400 1000
26 - 30 50.0 1100

Assembly Tag No: - HR1 or HR2 or HR3 - X


Detail No Pipe Size
SUPPORT No HR1, HR2, HR3
SUPPORT TYPE Non-Adjustable Hangers for Bare Pipes Sheet D1
PIPE SIZE ½" - 30"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Pipe Support No HR1, Hanger with 2-Bolt Clamp for Light Loads

Pipe Mark No 1 Size Mark No 2 Size Mark No 3 Size


Size (1 Off) (1 Off) (1 Off)
½ - 1½ L-12 CLR-12 R-12A
2-4 L-16 CLR-16 Threaded R-16A
6 - 12 Lug L-20 Clevis CLR-20 Sling Rod R-20A
14 - 18 L-24 CLR-24 R-24A
20 - 24 L-30 CLR-30 R-30A

Pipe Mark No 4 Size Mark No 5 Size Mark No 6 Size


Size (1 Off) (1 Off) (1 Off)
½ - 1½ WENR-12 M12
2-4 Weldless WENR-16 PC1 M16
6 - 12 Eye Nut WENR-20 Pipe Clip Size as Nut M20
14 - 18 WENR-24 Pipe M24
20 - 24 WENR-30 M30

Pipe Support No HR2, Hanger with 2- Bolt Clamp for Heavy Loads

Pipe Mark No 1 Size Mark No 2 Size Mark No 3 Size


Size (1 Off) (1 Off) (1 Off)
3 L-20 CLR-20 R-20A
4-8 L-24 CLR-24 Threaded R-24A
10 - 12 Lug L-30 Clevis CLR-30 Sling Rod R-30A
14 - 24 L-36 CLR-36 R-36A
26 - 30 L-42 CLR-42 R-42A

Pipe Mark No 4 Size Mark No 5 Size Mark No 6 Size


Size (1 Off) (1 Off) (1 Off)
3 WENR-20 M20
4-8 Weldless WENR-24 PC2 M24
10 - 12 Eye Nut WENR-30 Pipe Clip Size as Nut M30
14 - 24 WENR-36 Pipe M36
26 - 30 WENR-42 M42

Pipe Support No HR3, Hanger with Lug for Light Loads

Pipe Mark No 1 Size Mark No 2 Size Mark No 3 Size Mark No 6 Size


Size (2 Off) (2 Off) (1 Off) (1 Off)
½ - 1½ Welding L-12 CLR-12 Threaded R-12A M12
2-4 Lug L-16 Clevis CLR-16 Sling Rod R-16A Nut M16
6 - 10 L-20 CLR-20 R-20A M20

SUPPORT No HR1, HR2, HR3


SUPPORT TYPE Non-Adjustable Hangers for Bare Pipes (Dimensions) Sheet D2
PIPE SIZE ½" - 30"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

H
3

Supt. No HR4 (Light Loads)


Supt. No HR5 (Heavy Loads)

HR4 HR5
Pipe Maximum Maximum Dimension H
Size Load (KN) Load (KN) Maximum Minimum
½-1 5.0 500
1½ - 2 5.0 2000
3-4 10.0 600
6-8 10.0 30.0 700
10 - 12 15.0 40.0 2200 900
14 18.0 40.0 1000
16 - 20 23.0 45.0 2400 1100
22 - 24 23.0 50.0 1200

Assembly Tag No: - HR4 or HR5 - X


Detail No Pipe Size
SUPPORT No HR4, HR5
SUPPORT TYPE Non-Adjustable Hanger for Insulated Pipes Sheet D3
PIPE SIZE ½" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Pipe Support No HR4, Hanger with 3-Bolt Clamp for Light Loads

Pipe Mark No 1 Size Mark No 2 Size Mark No 3 Size


Size (1 Off) (1 Off) (1 Off)
½-1 L-12 CLR-12 R-12A
1½ - 4 L-16 CLR-16 Threaded R-16A
6 - 12 Lug L-20 Clevis CLR-20 Sling Rod R-20A
14 - 20 L-24 CLR-24 R-24A
22 - 24 L-30 CLR-30 R-30

Pipe Mark No 4 Size Mark No 5 Size Mark No 6 Size


Size (1 Off) (1 Off) (1 Off)
½-1 WENR-12 M12
1½ - 4 Weldless WENR-16 PC3 M16
6 - 12 Eye Nut WENR-20 Pipe Clip Size as Nut M20
14 - 20 WENR-24 Pipe M24
22 - 24 WENR-30 M30

Pipe Support No HR5, Hanger with 3- Bolt Clamp for Heavy Loads

Pipe Mark No 1 Size Mark No 2 Size Mark No 3 Size


Size (1 Off) (1 Off) (1 Off)
6-8 Welding L-30 CLR-30 Threaded R-30A
10 - 14 Lug L-36 Clevis CLR-36 Sling Rod R-36A
16 - 24 L-42 CLR-42 R-42A

Pipe Mark No 4 Size Mark No 5 Size Mark No 6 Size


Size (1 Off) (1 Off) (1 Off)
6-8 Weldless WENR-30 PC4 M30
10 - 14 Eye Nut WENR-36 Pipe Clip Size as Nut M36
16 - 24 WENR-42 Pipe M42

SUPPORT No HR4, HR5


SUPPORT TYPE Non-Adjustable Hanger for Insulated Pipes (Dim'ns) Sheet D4
PIPE SIZE ½" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

4
H

L.H. Thread
Rod, Nut &
8
5 Clevis (Typ)

6
1

Supt. No HR6 (Light Loads) Supt. No HR8 (Light Loads)


Supt. No HR7 (Heavy Loads)
HR6 HR7 HR8
Pipe Max Max Max Dimension H
Size Load (KN) Load (KN) Load (KN) Maximum Minimum
½ - 1½ 600
2 4.0 4.0
3 12.0 2000 700
4
6-8 7.0 800
10 7.0 20.0 1050
12 2200
14 - 18 12.0 35.0 1150
20 - 24 2400 1250
26 - 30 50.0 1350

Assembly Tag No: - HR6 or HR7 or HR8 - X


Detail No Pipe Size
SUPPORT No HR6, HR7, HR8
SUPPORT TYPE Adjustable Hangers for Bare Pipes Sheet D5
PIPE SIZE ½" - 30"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Pipe Support No HR6, Hanger with 2-Bolt Clamp for Light Loads

Pipe Mark No 1 Size Mark No 2 Size Mark No 3 Size


Size (1 Off) (1 Off) (1 Off)
½ - 1½ L-12 CLR-12 R-12B
2-4 Welding L-16 CLR-16 Threaded R-16B
6 - 12 Lug L-20 Clevis CLR-20 Sling Rod R-20B
14 - 18 L-24 CLR-24 R-24B
20 - 24 L-30 CLR-30 R-30B

Pipe Mark No 4 Size Mark No 5 Size Mark No 6 Size Mark No 7 Size


Size (1 Off) (1 Off) (1 Off) (1 Off)
½ - 1½ T-12 WENL-12 M12
2-4 T-16 Weldless WENL-16 PC1 M16
6 - 12 Turnbuckle T-20 Eye Nut WENL-20 Pipe Clip Size as Nut M20
14 - 18 T-24 WENL-24 Pipe M24
20 - 24 T-30 WENL-30 M30

Pipe Support No HR7, Hanger with 2- Bolt Clamp for Heavy Loads

Pipe Mark No 1 Size Mark No 2 Size Mark No 3 Size


Size (1 Off) (1 Off) (1 Off)
3 L-20 CLR-20 R-20B
4-8 Welding L-24 CLR-24 Threaded R-24B
10 - 12 Lug L-30 Clevis CLR-30 Sling Rod R-30B
14 - 24 L-36 CLR-36 R-36B
26 - 30 L-42 CLR-42 R-42B

Pipe Mark No 4 Size Mark No 5 Size Mark No 6 Size Mark No 7 Size


Size (1 Off) (1 Off) (1 Off) (1 Off)
3 T-20 WENL-20 M20
4-8 T-24 Weldless WENL-24 PC2 M24
10 - 12 Turnbuckle T-30 Eye Nut WENL-30 Pipe Clip Size as Nut M30
14 - 24 T-36 WENL-36 Pipe M36
26 - 30 T-42 WENL-42 M42

Pipe Support No HR8, Hanger with Lug for Light Loads

Pipe Mark No 1 Size Mark No 2 Size Mark No 8 Size


Size (2 Off) (1 Off) (1 Off)
½ - 1½ Welding L-12 CLR-12 CLL-12
2-4 Lug L-16 Clevis CLR-16 Clevis CLL-16
6 - 10 L-20 CLR-20 CLL-20

Pipe Mark No 3 Size Mark No 4 Size Mark No 7 Size


Size (1 Off) (1 Off) (1 Off)
½ - 1½ Threaded R-12B T-12 M12
2-4 Sling Rod R-16B Turnbuckle T-16 Nut M16
6 - 10 R-20B T-20 M20

SUPPORT No HR6, HR7, HR8


SUPPORT TYPE Adjustable Hangers for Bare Pipes (Dimensions) Sheet D6
PIPE SIZE ½" - 30"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

L.H. Thread H
Rod, Nut &
Weldless Eye
Nut

Supt. No HR9 (Light Loads)


Supt. No HR10 (Heavy Loads)

HR9 HR10
Pipe Maximum Maximum Dimension H
Size Load (KN) Load (KN) Maximum Minimum
½-1 5.0 700
1½ - 2 5.0 2000
3-4 10.0 800
6-8 10.0 30.0 900
10 - 12 15.0 40.0 2200 1150
14 18.0 40.0 1250
16 - 20 23.0 45.0 2400 1350
22 - 24 23.0 50.0 1450

Assembly Tag No: - HR9 or HR10 - X


Detail No Pipe Size
SUPPORT No HR9, HR10
SUPPORT TYPE Adjustable Hanger for Insulated Pipes Sheet D7
PIPE SIZE ½" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Pipe Support No HR9, Hanger with 3-Bolt Clamp for Light Loads

Pipe Mark No 1 Size Mark No 2 Size Mark No 3 Size


Size (1 Off) (1 Off) (1 Off)
½-1 L-12 CLR-12 R-12B
1½ - 4 Welding L-16 CLR-16 Threaded R-16B
6 - 12 Lug L-20 Clevis CLR-20 Sling Rod R-20B
14 - 20 L-24 CLR-24 R-24B
22 - 24 L-30 CLR-30 R-30B

Pipe Mark No 4 Size Mark No 5 Size Mark No 6 Size


Size (1 Off) (1 Off) (1 Off)
½-1 T-12 WENL-12
1½ - 4 T-16 Weldless WENL-16 PC3
6 - 12 Turnbuckle T-20 Eye Nut WENL-20 Pipe Clip Size as
14 - 20 T-24 WENL-24 Pipe
22 - 24 T-30 WENL-30

Pipe Support No HR10, Hanger with 3- Bolt Clamp for Heavy Loads

Pipe Mark No 1 Size Mark No 2 Size Mark No 3 Size


Size (1 Off) (1 Off) (1 Off)
6-8 Welding L-30 CLR-30 Threaded R-30B
10 - 14 Lug L-36 Clevis CLR-36 Sling Rod R-36B
16 - 24 L-42 CLR-42 R-42B

Pipe Mark No 4 Size Mark No 5 Size Mark No 6 Size


Size (1 Off) (1 Off) (1 Off)
6-8 T-30 Weldless WENL-30 PC4
10 - 14 Turnbuckle T-36 Eye Nut WENL-36 Pipe Clip Size as
16 - 24 T-42 WENL-42 Pipe

SUPPORT No HR9, HR10


SUPPORT TYPE Adjustable Hanger for Insulated Pipes (Dimensions) Sheet D8
PIPE SIZE ½" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

3
H

Isolation Strip

Supt. No HR101 (Light Loads)


Supt. No HR102 (Heavy Loads)

HR101 HR102
Pipe Max Max Dimension H
Size Load (KN) Load (KN) Maximum Minimum
½ - 1½ 400
2 4.0
3 12.0 2000 500
4
6-8 600
10 7.0 20.0 800
12 2200
14 - 18 12.0 40.0 900
20 - 24 2400 1000
26 - 30 50.0 1100

Assembly Tag No: - HR101 or HR102 - X


Detail No Pipe Size
SUPPORT No HR101, HR102
SUPPORT TYPE Non-Adjustable Hanger for Bare Stainless Steel Pipes Sheet D9
PIPE SIZE ½" - 30"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Pipe Support No HR101, Hanger with 2-Bolt Clamp for Light Loads

Pipe Mark No 1 Size Mark No 2 Size Mark No 3 Size


Size (1 Off) (1 Off) (1 Off)
½ - 1½ L-12 CLR-12 R-12A
2-4 Welding L-16 CLR-16 Threaded R-16A
6 - 12 Lug L-20 Clevis CLR-20 Sling Rod R-20A
14 - 18 L-24 CLR-24 R-24A
20 - 24 L-30 CLR-30 R-30A

Pipe Mark No 4 Size Mark No 5 Size Mark No 6 Size


Size (1 Off) (1 Off) (1 Off)
½ - 1½ WENR-12 M12
2-4 Weldless WENR-16 PC101 M16
6 - 12 Eye Nut WENR-20 Pipe Clip Size as Nut M20
14 - 18 WENR-24 Pipe M24
20 - 24 WENR-30 M30

Pipe Support No HR102, Hanger with 2- Bolt Clamp for Heavy Loads

Pipe Mark No 1 Size Mark No 2 Size Mark No 3 Size


Size (1 Off) (1 Off) (1 Off)
3 L-20 CLR-20 R-20A
4-8 Welding L-24 CLR-24 Threaded R-24A
10 - 12 Lug L-30 Clevis CLR-30 Sling Rod R-30A
14 - 24 L-36 CLR-36 R-36A
26 - 30 L-42 CLR-42 R-42A

Pipe Mark No 4 Size Mark No 5 Size Mark No 6 Size


Size (1 Off) (1 Off) (1 Off)
3 WENR-20 M20
4-8 Weldless WENR-24 PC102 M24
10 - 12 Eye Nut WENR-30 Pipe Clip Size as Nut M30
14 - 24 WENR-36 Pipe M36
26 - 30 WENR-42 M42

SUPPORT No HR101, HR102


SUPPORT TYPE Non-Adjustable Hanger for Bare Stainless Steel Pipes Sheet D10
PIPE SIZE ½" - 30"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

H
3

Isolation Strip Supt. No HR104 (Light Loads)


Supt. No HR105 (Heavy Loads)

HR104 HR105
Pipe Maximum Maximum Dimension H
Size Load (KN) Load (KN) Maximum Minimum
½-1 5.0 500
1½ - 2 5.0 2000
3-4 10.0 600
6-8 10.0 30.0 700
10 - 12 15.0 40.0 2200 900
14 18.0 40.0 1000
16 - 20 23.0 45.0 2400 1100
22 - 24 23.0 50.0 1200

Assembly Tag No: - HR104 or HR105 - X


Detail No Pipe Size
SUPPORT No HR104, HR105
SUPPORT TYPE Non-Adjustable Hanger for Insulated SS Pipes Sheet D11
PIPE SIZE ½" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Pipe Support No HR104, Hanger with 3-Bolt Clamp for Light Loads

Pipe Mark No 1 Size Mark No 2 Size Mark No 3 Size


Size (1 Off) (1 Off) (1 Off)
½-1 L-12 CLR-12 R-12A
1½ - 4 Welding L-16 CLR-16 Threaded R-16A
6 - 12 Lug L-20 Clevis CLR-20 Sling Rod R-20A
14 - 20 L-24 CLR-24 R-24A
22 - 24 L-30 CLR-30 R-30

Pipe Mark No 4 Size Mark No 5 Size Mark No 6 Size


Size (1 Off) (1 Off) (1 Off)
½-1 WENR-12 M12
1½ - 4 Weldless WENR-16 PC103 M16
6 - 12 Eye Nut WENR-20 Pipe Clip Size as Nut M20
14 - 20 WENR-24 Pipe M24
22 - 24 WENR-30 M30

Pipe Support No HR105, Hanger with 3- Bolt Clamp for Heavy Loads

Pipe Mark No 1 Size Mark No 2 Size Mark No 3 Size


Size (1 Off) (1 Off) (1 Off)
6-8 Welding L-30 CLR-30 Threaded R-30A
10 - 14 Lug L-36 Clevis CLR-36 Sling Rod R-36A
16 - 24 L-42 CLR-42 R-42A

Pipe Mark No 4 Size Mark No 5 Size Mark No 6 Size


Size (1 Off) (1 Off) (1 Off)
6-8 Weldless WENR-30 PC104 M30
10 - 14 Eye Nut WENR-36 Pipe Clip Size as Nut M36
16 - 24 WENR-42 Pipe M42

SUPPORT No HR104, HR105


SUPPORT TYPE Non-Adjustable Hanger for Insulated SS Pipes Sheet D12
PIPE SIZE ½" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

4
H L.H. Thread
Rod, Nut &
Weldless Eye
5 Nut

Isolation Strip

Supt. No HR106 (Light Loads)


Supt. No HR107 (Heavy Loads)

HR106 HR107
Pipe Max Max Dimension H
Size Load (KN) Load (KN) Maximum Minimum
½ - 1½ 600
2 4.0
3 12.0 2000 700
4
6-8 800
10 7.0 20.0 1050
12 2200
14 - 18 12.0 35.0 1150
20 - 24 2400 1250
26 - 30 50.0 1350

Assembly Tag No: - HR106 or HR107 - X


Detail No Pipe Size
SUPPORT No HR106, HR107
SUPPORT TYPE Adjustable Hangers for Bare Stainless Steel Pipes Sheet D13
PIPE SIZE ½" - 30"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Pipe Support No HR106, Hanger with 2-Bolt Clamp for Light Loads

Pipe Mark No 1 Size Mark No 2 Size Mark No 3 Size


Size (1 Off) (1 Off) (1 Off)
½ - 1½ L-12 CLR-12 R-12B
2-4 Welding L-16 CLR-16 Threaded R-16B
6 - 12 Lug L-20 Clevis CLR-20 Sling Rod R-20B
14 - 18 L-24 CLR-24 R-24B
20 - 24 L-30 CLR-30 R-30B

Pipe Mark No 4 Size Mark No 5 Size Mark No 6 Size Mark No 7 Size


Size (1 Off) (1 Off) (1 Off) (1 Off)
½ - 1½ T-12 WENL-12 M12
2-4 T-16 Weldless WENL-16 PC101 M16
6 - 12 Turnbuckle T-20 Eye Nut WENL-20 Pipe Clip Size as Nut M20
14 - 18 T-24 WENL-24 Pipe M24
20 - 24 T-30 WENL-30 M30

Pipe Support No HR107, Hanger with 2- Bolt Clamp for Heavy Loads

Pipe Mark No 1 Size Mark No 2 Size Mark No 3 Size


Size (1 Off) (1 Off) (1 Off)
3 L-20 CLR-20 R-20B
4-8 Welding L-24 CLR-24 Threaded R-24B
10 - 12 Lug L-30 Clevis CLR-30 Sling Rod R-30B
14 - 24 L-36 CLR-36 R-36B
26 - 30 L-42 CLR-42 R-42B

Pipe Mark No 4 Size Mark No 5 Size Mark No 6 Size Mark No 7 Size


Size (1 Off) (1 Off) (1 Off) (1 Off)
3 T-20 WENL-20 M20
4-8 T-24 Weldless WENL-24 PC102 M24
10 - 12 Turnbuckle T-30 Eye Nut WENL-30 Pipe Clip Size as Nut M30
14 - 24 T-36 WENL-36 Pipe M36
26 - 30 T-42 WENL-42 M42

SUPPORT No HR106, HR107


SUPPORT TYPE Adjustable Hangers for Bare SS Pipes (Dimensions) Sheet D14
PIPE SIZE ½" - 30"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

L.H. Thread H
Rod, Nut &
Weldless Eye
Nut

Isolation Strip. Supt. No HR109 (Light Loads)


Supt. No HR110 (Heavy Loads)

HR109 HR110
Pipe Maximum Maximum Dimension H
Size Load (KN) Load (KN) Maximum Minimum
½-1 5.0 700
1½ - 2 5.0 2000
3-4 10.0 800
6-8 10.0 30.0 900
10 - 12 15.0 40.0 2200 1150
14 18.0 40.0 1250
16 - 20 23.0 45.0 2400 1350
22 - 24 23.0 50.0 1450

Assembly Tag No: - HR109 or HR110 - X


Detail No Pipe Size
SUPPORT No HR109, HR110
SUPPORT TYPE Adjustable Hanger for Insulated Stainless Steel Pipes Sheet D15
PIPE SIZE ½" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Pipe Support No HR109, Hanger with 3-Bolt Clamp for Light Loads

Pipe Mark No 1 Size Mark No 2 Size Mark No 3 Size


Size (1 Off) (1 Off) (1 Off)
½-1 L-12 CLR-12 R-12B
1½ - 4 Welding L-16 CLR-16 Threaded R-16B
6 - 12 Lug L-20 Clevis CLR-20 Sling Rod R-20B
14 - 20 L-24 CLR-24 R-24B
22 - 24 L-30 CLR-30 R-30B

Pipe Mark No 4 Size Mark No 5 Size Mark No 6 Size


Size (1 Off) (1 Off) (1 Off)
½-1 T-12 WENL-12
1½ - 4 T-16 Weldless WENL-16 PC103
6 - 12 Turnbuckle T-20 Eye Nut WENL-20 Pipe Clip Size as
14 - 20 T-24 WENL-24 Pipe
22 - 24 T-?? WENL-30

Pipe Support No HR110, Hanger with 3- Bolt Clamp for Heavy Loads

Pipe Mark No 1 Size Mark No 2 Size Mark No 3 Size


Size (1 Off) (1 Off) (1 Off)
6-8 Welding L-30 CLR-30 Threaded R-30B
10 - 14 Lug L-36 Clevis CLR-36 Sling Rod R-36B
16 - 24 L-42 CLR-42 R-42B

Pipe Mark No 4 Size Mark No 5 Size Mark No 6 Size


Size (1 Off) (1 Off) (1 Off)
6-8 T-30 Weldless WENL-30 PC104
10 - 14 Turnbuckle T-36 Eye Nut WENL-36 Pipe Clip Size as
16 - 24 T-42 WENL-42 Pipe

SUPPORT No HR109, HR110


SUPPORT TYPE Adjustable Hanger for Insulated Stainless Steel Pipes Sheet D16
PIPE SIZE ½" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

3
H
2

Max Load (KN)


4

50 = = 50

Size Dimensions Max Load Mark No 4 M.T.O.


Code L H (Max) H (Min) (KN) (1 Off) Length
A1 500 500
A2 700 2000 400 4.0 IPE 100 700
A3 900 900
B1 900 900
B2 1100 3000 500 20.0 IPE 200 1100
B3 1300 1300
B4 1500 1500
C1 1500 1500
C2 1700 3000 800 40.0 IPE 300 1700
C3 1900 1900
C4 2100 2100

Size Mark No 1 Size Mark No 2 Size Mark No 3 Size


Code (4 Off) (4 Off) (2 Off)
A Welding L-12 CL-12 Threaded R-12A
B Lug L-24 Clevis CL-24 Sling Rod R-24C
C L-36 CL-36 R-36C
Assembly Tag No: - TH - XX
Detail No Size Code
SUPPORT No TH
SUPPORT TYPE Trapeze Hanger Sheet D17
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

For Details of Spring H


Hangers Refer to
Spring Spec No
60-0000-L-SPE-1003

SH1 SH2
Spring Hanger Spring Hanger
For Bare Pipes For Insulated Pipes

Assembly Tag No: - SH1 or SH2 Dimensions Required: - H


Item No (Ref Spring Spec) is also required
Detail No
SUPPORT No SH1, SH2
SUPPORT TYPE Spring Hangers from Underside of Steel Sheet D18
PIPE SIZE 2"- 36"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

For Details of Spring


Hangers Refer to
Spring Spec No
60-0000-L-SPE-1003

SH3 SH4
Spring Hanger Spring Hanger
For Bare Pipes For Insulated Pipes

Assembly Tag No: - SH3 or SH4 Dimensions Required: - H


Item No (Ref Spring Spec) is also required
Detail No
SUPPORT No SH3, SH4
SUPPORT TYPE Spring Hangers from Top of Steel Sheet D19
PIPE SIZE 2"- 36"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

For Details of Spring


Hangers Refer to
Spring Spec No
60-0000-L-SPE-1003
H

Detail for Pipes


with Shoes
H

Where required shoe to be called


up separately by piping designer
L

Assembly Tag No: - SH5 Dimensions Required: - H, L


Item No (Ref Spring Spec) is also required
Detail No
SUPPORT No SH5
SUPPORT TYPE Trapeze Spring Hanger from Underside of Steel Sheet D20
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

For Details of Spring


Hangers Refer to
Spring Spec No
60-0000-L-SPE-1003

Detail for Pipes


H
with Shoes

Where required shoe to be called


up separately by piping designer
L

Assembly Tag No: - SH6 Dimensions Required: - H, L


Item No (Ref Spring Spec) is also required
Detail No
SUPPORT No SH6
SUPPORT TYPE Trapeze Spring Hanger from Top of Steel Sheet D21
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

For Details of Spring


Hangers Refer to
Spring Spec No
60-0000-L-SPE-1003

Detail for Pipes


H with Shoes

Where required shoe to be called


up separately by piping designer
L

Assembly Tag No: - SH7 Dimensions Required: - H, L


Item No (Ref Spring Spec) is also required
Detail No
SUPPORT No SH7
SUPPORT TYPE Trapeze Spring Hanger, Springs underneath pipe Sheet D22
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Shoe (ref. By PFD)

For Details of Spring


Hangers Refer to
Spring Spec No
H
60-0000-L-SPE-1003

Stitch weld
spring to
supporting
steelwork

Base Support
(ref. BS1 or BS6
by PFD)

For Details of Spring


Hangers Refer to
Spring Spec No H
60-0000-L-SPE-1003

Stitch weld spring to


supporting steelwork

Assembly Tag No: - SH8


Dimensions Required: - H
Detail No Item No (Ref Spring Spec) is also required
SUPPORT No SH8
SUPPORT TYPE Pedestal Spring Sheet D23
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

For Details of Spring


Hangers Refer to
H Spring Spec No
60-0000-L-SPE-1003

SH11 SH12
Constant Constant
Spring Hanger Spring Hanger
Trapeze Trapeze

Assembly Tag No: - SH11 or SH12 Dimensions Required: - H


Item No (Ref Spring Spec) is also required
Detail No
SUPPORT No SH11, SH12
SUPPORT TYPE Constant Spring Hangers from Underside of Steel Sheet D24
PIPE SIZE 2"- 36"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

For Details of Spring


Hangers Refer to
Spring Spec No
60-0000-L-SPE-1003

SH13 SH14
Constant Constant
Spring Hanger Spring Hanger

Assembly Tag No: - SH13 or SH14 Dimensions Required: - H


Detail No Item No (Ref Spring Spec) is also required

SUPPORT No SH13, SH14


SUPPORT TYPE Constant Spring Hangers from Top of Steel Sheet D25
PIPE SIZE 2"- 36"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

For Details of Spring


H
Hangers Refer to
Spring Spec No
60-0000-L-SPE-1003

SH15
Constant
Spring Hanger L
Trapeze

Detail for Pipes


with Shoes

Where required shoe to be called


up separately by piping designer L

For Details of Spring


Hangers Refer to
H
Spring Spec No
60-0000-L-SPE-1003

SH16
Constant
Spring Hanger
Trapeze

Assembly Tag No: - SH15 or SH16 Dimensions Required: - H,L


Detail No Item No (Ref Spring Spec) is also required
SUPPORT No SH15, SH16
SUPPORT TYPE Constant Spring Hangers from Underside of Steel Sheet D26
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

For Details of Spring


Hangers Refer to
Spring Spec No
60-0000-L-SPE-1003

H
SH17
Constant
Spring Hanger
Trapeze

L
H

Detail for Pipes


with Shoes

Where required shoe to be called


up separately by piping designer
L

For Details of Spring


Hangers Refer to
Spring Spec No
60-0000-L-SPE-1003

H
SH18
Constant
Spring Hanger
Trapeze

Assembly Tag No: - SH17 or SH18 Dimensions Required: - H,L


Detail No Item No (Ref Spring Spec) is also required
SUPPORT No SH17, SH18
SUPPORT TYPE Constant Spring Hangers from Top of Steel Sheet D27
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

SH19
Constant
Pedestal Spring

For Details of Spring


Hangers Refer to H
Spring Spec No
60-0000-L-SPE-1003

SH20
Constant
Pedestal Spring

For Details of Spring


Hangers Refer to H
Spring Spec No
60-0000-L-SPE-1003

Assembly Tag No: - SH19 or SH20 Dimensions Required: - H


Detail No Item No (Ref Spring Spec) is also required
SUPPORT No SH19, SH20
SUPPORT TYPE Constant Pedesal Springs Sheet D28
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

For Details of Spring


Hangers Refer to
Spring Spec No
60-0000-L-SPE-1003

View A-A

Assembly Tag No: - SH9 Dimensions Required: - H


Item No (Ref Spring Spec) is also required
Detail No
SUPPORT No SH9
SUPPORT TYPE Spring Hangers from Top of Steel to Elbow hanger Sheet D29
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

For Details of Spring


Hangers Refer to
Spring Spec No
60-0000-L-SPE-1003

X X

X X
SH21 SH22

View X-X

Assembly Tag No: - SH21 or SH22 Dimensions Required: - H


Item No (Ref Spring Spec) is also required
Detail No
SUPPORT No SH21, SH22
SUPPORT TYPE Spring Hangers for Cold Insulated Pipes Sheet D30
PIPE SIZE 2"- 36"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

For Details of Spring


Hangers Refer to
Spring Spec No
60-0000-L-SPE-1003

View A-A

Assembly Tag No: - SH10 Dimensions Required: - H


Item No (Ref Spring Spec) is also required
Detail No
SUPPORT No SH10
SUPPORT TYPE Spring Hangers from Underside of Steel to Pipe Elbow. Sheet D31
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

For Details of Spring


Hangers Refer to
Spring Spec No
60-0000-L-SPE-1003

View A-A

Assembly Tag No: - SH23 Dimensions Required: - H


Item No (Ref Spring Spec) is also required
Detail No
SUPPORT No SH23
SUPPORT TYPE Spring Hangers from Underside of Steel to Pipe Lug. Sheet D32
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

For Details of Spring


Hangers Refer to
Spring Spec No
60-0000-L-SPE-1003

View A-A

Assembly Tag No: - SH24 Dimensions Required: - H


Item No (Ref Spring Spec) is also required
Detail No
SUPPORT No SH24
SUPPORT TYPE Spring Hangers from Top of Steel to Pipe Lug Sheet D33
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

3
2400
2

Site Drill 50 50
22dia holes
through the 1800
centreline of
the top flange
of the beam

Support Mark No 1 No Off Mark No 2 No Off


PS15 M10 Alphawedge 2 M10 Nuts 6
Deck Fixing

Support Mark No 3 Length Mark No 4 Length


PS15 M10 Threaded Rod 5000 UPN 100 1800

NOTES 1- This support shall be used for HVAC piping only


2- Threaded rods and beam shall be trimed to suit

Assembly Tag No: - PS15


Detail No
SUPPORT No PS15
SUPPORT TYPE Horizontal Pipe Support - Single Bank Sheet D34
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
L
Reference = = Note - View Looking
Pipe Y
North or East

T.O.S. EL Support No
P1-A
L
= =
Support No
P1-B/C/D/E/F 20
1

H
1
Site trim and field
weld to existing H
structure

For alternative welding


arrangements refer to
Support No P2

Allowable
Dimension
Total Bending
Size Code Mark No1 Notes
Length Moment
H L
(KNm)
A1 300 70 X 8 1300 For use only on
A2 1000 500 Angle 1500 0.5 Pipe Sizes ≤ 2"
A3 750 1800
B1 300 1200
B2 1000 500 HEA 100 1400 4.0
B3 750 1650
B4 1000 1900
C1 300 2200
C2 2000 500 HEA 100 2400 4.0 For use only on
C3 750 2650 Pipe Sizes ≤ 4"
C4 1000 2900
D1 300 2140
D2 2000 500 HEA 160 2340 8.0
D3 750 2600
D4 1000 2840
E1 300 3140
E2 3000 500 HEA 160 3340 8.0 For use only on
E3 750 3600 Pipe Sizes ≤ 4"
E4 1000 3840
F1 300 3100
F2 3000 500 HEA 200 3300 12.0
F3 750 3550
F4 1000 3800
Assembly Tag No: - P1 - XX, Dimension "Y", T.O.S. EL
Detail No Size Code
SUPPORT No P1
SUPPORT TYPE T-Post from existing structure Sheet E1
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
Preferred Arrangement Alternative Welding
Arrangements for Pipe
L (typ) Support Nos P1 - P9.
2
= =
T.O.S. EL

HEA 160 or
1 200
HEA 100 or
min
70 x 8 Angle

20

H
Site trim and field 200
weld to existing min
structure
HEA 100 or 20
70 x 8 Angle
10

Flange toes 200


cut back 10mm min
to ensure a
good weld
20

Notes: - 1- Size Codes "B" and "D" shall only be used for Pipe Sizes ≤ 4"
Allowable
Dimension
Size Mark Total Mark Area Bending
Code No 1 Length No 2 (cm²) Moment
H L
(KNm)
A1 1000 200 HEA 100 1000 12 Thk 400 4.0
A2 300 1000 square 900
B1 2000 200 HEA 100 2000 plate 400 4.0 Note 1
B2 300 2000 900
C1 2000 300 HEA 160 2000 900 8.0
C2 450 2000 15 Thk 2025
D1 3000 300 HEA 160 3000 square 900 8.0 Note 1
D2 450 3000 plate 2025
E1 3000 400 HEA 200 3000 1600 12.0
E2 550 3000 3025

Assembly Tag No: - P2 - XX, T.O.S. EL


Detail No Size Code
SUPPORT No P2
SUPPORT TYPE Post with Square Plate from exisiting structure Sheet E2
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

20 L
Note - View Looking ????
Y
Reference Reference
Pipe Pipe

T.O.S. EL 20 L
Y

T.O.S. EL
1
20
H
Site trim and field 1
weld to existing H
structure

For alternative welding


arrangements refer to
Support No P2
Support No P3-B/C/D/E/F Support No P3-A

Note: - 1- This support is not to be used for anchoring pipes


2- The support can not be used on lines 6" and above without consultation with
the stress engineer.

Allowable
Dimension
Size Mark Total Bending
Notes
Code No 1 Length Moment
H L
(KNm)
A1 1000 250 70 X 8 1350 0.5 For use only on
A2 500 Angle 1550 Pipe Sizes ≤ 2"
B1 1000 250 HEA 100 1220 4.0
B2 500 1470
C1 2000 250 HEA 100 2220 4.0 For use only on
C2 500 2470 Pipe Sizes ≤ 4"
D1 2000 250 HEA 160 2190 8.0
D2 500 2440
E1 3000 250 HEA 160 3190 8.0 For use only on
E2 500 3440 Pipe Sizes ≤ 4"
F1 3000 250 HEA 200 3170 12.0
F2 500 3420
Assembly Tag No: - P3 - XX, Dimension "Y", T.O.S. EL, View looking ????
Detail No Size Code
SUPPORT No P3
SUPPORT TYPE Cantilevered-Post from existing structure Sheet E3
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

L
K M K
Reference Y
Pipe

20
T.O.S. EL

1
H Note - View Looking
Site trim and field North or East
weld to existing
structure

For alternative welding


arrangements refer to
Support No P2

Note: - 1- The support shall be used for pipes ≤ 2"

Size Dimension
Code H L M K
A1 1000 1100 1000 50
A2 1500 250

Size Mark Total Max Bending


Code No 1 Length Moment (KNm)
A1 70 x 8 3100 0.5
A2 Angle 3500

Assembly Tag No: - P4 - XX, Dimension "Y", T.O.S. EL


Detail No Size Code
SUPPORT No P4
SUPPORT TYPE Goal Post from Structure Sheet E4
PIPE SIZE ½" - 2"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
L
K M K
Reference Y
Pipe

T.O.S. EL

Note - View Looking 1


North or East H

Site trim and weld


to existing structure

For alternative welding


arrangements refer to
Support No P2

Allowable
Dimension
Size Mark Total Bending
Code No 1 Length Moment
H L K M
(KNm)
B1 1300 150 3110
B2 1000 1600 300 1000 HEA 100 3410 4.0
B3 2000 500 3810
C1 1400 100 1200 3100
C2 1000 1700 250 3400
C3 2000 250 1500 3700
C4 2500 500 HEA 160 4200 8.0
C5 1400 100 1200 5100
C6 2000 1700 250 5400
C7 2000 250 1500 5700
C8 2500 500 6200
D1 2000 150 1700 3620
D2 1000 2500 250 2000 4120
D3 3000 500 4620
D4 2000 150 1700 5620
D5 2000 2500 250 2000 HEA 200 6120 12.0
D6 3000 500 6620
D7 2000 150 1700 7620
D8 3000 2500 250 2000 8120
D9 3000 500 8620
Assembly Tag No: - P4 - XX, Dimension "Y", T.O.S. EL
Detail No Size Code
SUPPORT No P4
SUPPORT TYPE Goal Post from Grade or Structure Sheet E5
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

T.O.S. EL

Site trim and field


weld to existing
structure

For alternative welding


arrangements refer to
Support No P2
Note: - 1- For dimension "H" see Table below

Allowable
Size Dim'n Mark Total Bending
Code H No 1 Length Moment
(KNm)
A 1000 HEA 100 1000 4.0
B 2000 HEA 100 2000 4.0
C 2000 HEA 160 2000 8.0
D 3000 HEA 160 3000 8.0

Assembly Tag No: - P5 - X, T.O.S. EL


Detail No Size Code
SUPPORT No P5
SUPPORT TYPE Post from existing structure Sheet E6
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

L
K M
Reference
Y
Pipe

T.O.S. EL

Site trim and Field


weld to existing
structure

Note - View Looking ????

Allowable
Dimension
Size Mark Total Bending
Code No 1 Length Moment
H L K M
(KNm)
A1 1000 1600 100 2500
A2 2000 500 1500 HEA 160 2900 8.0
A3 2000 1600 100 3500
A4 2000 500 3900
B1 1000 2120 120 3020
B2 2500 500 3400
B3 2000 2120 120 2000 HEA 200 4020 12.0
B4 2500 500 4400
B5 3000 2120 120 5020
B6 2500 500 5400

Assembly Tag No: - P6 - XX, Dimension "Y", T.O.S. EL, View looking ????
Detail No Size Code
SUPPORT No P6
SUPPORT TYPE Welded Cantilevered Post from existing structure Sheet E7
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3
For alternative welding
arrangements refer to
Support No P2

Site trim and weld


to existing beam Reference
Pipe
H

1
H
Reference T.O.S. EL
Pipe 1

20 Y

= =
T.O.S. EL
L

Y Note - View Looking


North or East
= =

Allowable
Dimension
M.T.O. Bending
Size Code Mark No1 Notes
Length Moment
H L
(KNm)
A1 1000 500 70 X 8 1550 0.5 For use only on
A2 750 Angle 1800 Pipe Sizes ≤ 2"
B1 1000 750 HEA 100 1750 4.0
B2 1000 2000
C1 2000 750 HEA 100 2750 4.0 See Note 1
C2 1000 3000
D1 2000 750 HEA 160 2750 8.0
D2 1000 3000
E1 3000 750 HEA 160 3750 8.0 See Note 1
E2 1000 4000
F1 3000 750 HEA 200 3750 12.0
F2 1000 4000

NOTE 1- The support can not be used on lines 6" and above without consultation with
the stress engineer.
Assembly Tag No: - P7 - XX, Dimension "Y", T.O.S. EL
Detail No Size Code
SUPPORT No P7
SUPPORT TYPE Inverted T-Post Sheet E8
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
For alternative welding
arrangements refer to
Support No P2

Site trim and weld Reference


to existing beam 1 Pipe H

H Reference
Pipe
T.O.S. EL

1
20 Y
L
20
T.O.S. EL

Y Note - View Looking ????


20
L

Note: - 1- This support is not to be used for anchoring pipes


2- The support can not be used on lines 6" and above without consultation with
the stress engineer.

Size Dimension Mark M.T.O. Max Bending Notes


Code H L No 1 Length Moment (KNm)
A1 1000 300 70 X 8 1420 0.5 For use only on
A2 500 Angle 1620 Pipe Sizes ≤ 2"
B1 1000 500 HEA 100 1570 4.0
C1 2000 500 HEA 160 2600 8.0
C2 750 2850

Assembly Tag No: - P8 - XX, Dimension "Y", T.O.S. EL, View looking ????
Detail No Size Code
SUPPORT No P8
SUPPORT TYPE Inverted Cantilevered Post Sheet E9
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
For alternative welding
arrangements refer to
Support No P2

Site trim and weld


to existing beam
1

Reference
H
Pipe
1

T.O.S. EL

20
Y

50 L 50

Note - View Looking


North or East

Note: - 1- The support shall be used for pipes ≤ 2"

Size Dimension Mark M.T.O. Max Bending


Code H L No 1 Length Moment (KNm)
A1 750 70 X 8 2950
A2 1000 1000 Angle 3200 0.5
A3 1250 3500

Assembly Tag No: - P9 - XX, Dimension "Y", T.O.S. EL


Detail No Size Code
SUPPORT No P9
SUPPORT TYPE Inverted Goal Post Sheet E10
PIPE SIZE ½" - 2"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
For alternative welding
arrangements refer to
Support No P2

Site trim and weld


to existing beam

Reference
1 H
Pipe
1

T.O.S. EL

20
Y
Note - View Looking
L North or East

Size Dimension Mark M.T.O. Max Bending


Code H L No 1 Length Moment (KNm)
B1 800 2940
B2 1000 1200 HEA 100 3340 4.0
B3 1600 3740
C1 800 3000
C2 1000 1200 3400
C3 1600 3800
C4 2000 HEA 160 4200 8.0
C5 800 5000
C6 2000 1200 5400
C7 1600 5800
C8 2000 6200
D1 1000 2500 4740
D2 3000 5240
D3 2000 2500 6740
D4 3000 7240
D5 1200 HEA 200 7440 12.0
D6 1600 7840
D7 3000 2000 8240
D8 2500 8740
D9 3000 9240
Assembly Tag No: - P9 - XX, Dimension "Y", T.O.S. EL
Detail No Size Code
SUPPORT No P9
SUPPORT TYPE Inverted Goal Post Sheet E11
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3

Site trim and weld


to existing beam

Note - View Looking ????


1

H
Site trim and weld
Reference 1 to existing column
Pipe

T.O.S. EL

20
Y
L

Size Dimension Mark M.T.O. Max Bending


Code H L No 1 Length Moment (KNm)
A1 1000 1000 HEA 100 2070 4.0
B1 1000 1000 2100
B2 1500 HEA 160 2600 8.0
B3 2000 1000 3100
B4 1500 3600
C1 1000 1500 2620
C2 2000 3120
C3 2000 1500 HEA 200 3620 12.0
C4 2000 4120
C5 3000 1500 4620
C6 2000 5120

Assembly Tag No: - P10 - XX, Dimension "Y", T.O.S. EL, View Looking
Detail No Size Code
SUPPORT No P10
SUPPORT TYPE Inverted Welded Cantilevered-Post Sheet E12
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Main Transverse
Intermediate
Beam HEA 500
Beam HEA 240/400

Locally remove fire proofing,


weld support to existing
beams. K
H

TOS EL

20
4000

Note: - 1- This support shall only be used in the main N-S SGP piperacks for pipes ≤ 6" to
keep the pipe spans within acceptable limits. (See Sketch below)

N Main Beam

Intermediate
Beam

Support
Point (typ)

Size Dimension Mark M.T.O. Max Load TOS EL


Code H K No 1 Length (KN)
A1 1010 1220 6370 4500 or 7500
A2 510 720 HEA 100 5370 5.0 10500
A3 1310 1410 6860 114200

Assembly Tag No: - P11 - XX


Detail No Size Code
SUPPORT No P11
SUPPORT TYPE Inverted Goal Post (for piperacks only) Sheet E13
PIPE SIZE 2" - 6"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Reference
Pipe Note - View Looking ????

T.O.S. EL

1
Y

K M
L

Max Load (typ)

Notes: - 1- Size Code "A" shall only be used for small bore lines ≤ 1½" where the
max loads are nominal

Size Dimensions Mark M.T.O. Max Loads (KN)


Code K (Max) M (Min) L No 1 Length Vertical Horizontal
A1 200 100 300 70 x 8 300 (Note 1) (Note 1)
A2 400 500 Angle 500 (Note 1) (Note 1)
B1 200 350 350 9.0 3.0
B2 400 150 550 HEA 100 550 9.0 3.0
B3 600 750 750 6.0 2.0
C1 200 400 400 15.0 5.0
C2 400 600 600 15.0 5.0
C3 600 200 800 HEA 160 800 15.0 5.0
C4 800 1000 1000 12.0 4.0
C5 1000 1200 1200 10.0 3.0

Assembly Tag No: - P21 - XX, Dimension "Y", T.O.S. EL, View looking ????
Detail No Size Code
SUPPORT No P21
SUPPORT TYPE Cantilevers Sheet E14
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
Reference
Note - View Looking ???? Pipe

T.O.S. EL
Support
No P22
1

20 Y
(200 min) K M
L

Max Load (typ)


Reference
Pipe

Note - View Looking ????

T.O.S. EL

Support
No P23 1

Y 20

M K (200 min)
L
Notes: - 1- Size Code "A" shall only be used for small bore lines (≤ 1½")
Size Dimensions Mark M.T.O. Max Loads (KN)
Code L K (Max) M (Min) No 1 Length Vertical Horizontal
A1 400 400
A2 600 70 x 8 600 0.5 0.5
A3 800 400 100 Angle 800 (Note 1) (Note 1)
A4 1000 1000
A5 1200 1200
B1 600 600 4.0 1.0
B2 800 800 2.0 0.5
B3 1000 600 150 UPN 100 1000 2.0 0.5
B4 1200 1200 2.0 0.5
B5 1400 1400 2.0 0.5
C1 600 600 10.0 3.0
C2 800 800 7.5 2.5
C3 1000 1000 5.0 2.0
C4 1200 1000 200 UPN 160 1200 3.0 1.0
C5 1400 1400 3.0 1.0
C6 1600 1600 3.0 1.0
C7 1800 1800 3.0 1.0
Assembly Tag No: - P22 or P23 - XX, Dimension "Y", T.O.S. EL, View looking ????
Detail No Size Code
SUPPORT No P22, P23
SUPPORT TYPE Cantilevers Sheet E15
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
Reference
Note - View Looking ???? Pipe

T.O.S. EL
Support
No P24
1
Y
20 (200 min) K M
L

Max Load (typ)

Reference
Note - View Looking ????
Pipe

T.O.S. EL
Support
No P25
1
Y
M K (200 min) 20
L

Notes: - 1- Size Code "A" shall only be used for small bore lines (≤ 1½")
Size Dimensions Mark M.T.O. Max Loads (KN)
Code L K (Max) M (Min) No 1 Length Vertical Horizontal
A1 400 400
A2 600 70 x 8 600 0.5 0.5
A3 800 400 100 Angle 800 (Note 1) (Note 1)
A4 1000 1000
A5 1200 1200
B1 600 600 4.0 1.0
B2 800 800 2.0 0.5
B3 1000 600 150 UPN 100 1000 2.0 0.5
B4 1200 1200 2.0 0.5
B5 1400 1400 2.0 0.5
C1 600 600 10.0 3.0
C2 800 800 7.5 2.5
C3 1000 1000 5.0 2.0
C4 1200 1000 200 UPN 160 1200 3.0 1.0
C5 1400 1400 3.0 1.0
C6 1600 1600 3.0 1.0
C7 1800 1800 3.0 1.0
Assembly Tag No: - P24 or P25 - XX, Dimension "Y", T.O.S. EL, View looking ????
Detail No Size Code
SUPPORT No P24, P25
SUPPORT TYPE Cantilevers Sheet E16
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Note - View Looking ????

Reference Y M
Pipe

T.O.S. EL

1
45º
K 200

Max Load

Size Dimensions Mark M.T.O. Max Loads (KN)


Code K (Max) M (Min) L No 1 Length Vertical Horizontal
A1 600 150 750 HEA 100 1599 12.0 3.5
B1 600 800 1649 30.0 10.0
B2 800 200 1000 HEA 160 2132 25.0 8.0
B3 1000 1200 2615 20.0 6.0

Assembly Tag No: - P26 - XX, Dimension "Y", T.O.S. EL, View looking ????
Detail No Size Code
SUPPORT No P26
SUPPORT TYPE Braced Cantilevers Sheet E17
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

K M

Y
Reference
Pipe Note - View Looking ????

T.O.S. EL

1
45º
200

Support
No P27 Max Load
1

Support
No P28

Support is Identical
200 min to P27 except it is
20 Opposite hand
(typ)
1

Size Dimensions Mark M.T.O. Max Loads (KN)


Code K (Max) M (Min) L No 1 Length Vertical Horizontal
A1 800 1649 15.0 5.0
A2 1000 2132 12.0 4.0
A3 1000 200 1200 UPN 160 2615 10.0 3.0
A4 1400 3098 8.0 2.5
A5 1600 3581 8.0 2.5
A6 1800 4064 8.0 2.5

Assembly Tag No: - P27 or P28 - XX, Dimension "Y", T.O.S. EL, View looking ????
Detail No Size Code
SUPPORT No P27, P28
SUPPORT TYPE Braced Cantilevers Sheet E18
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

K M
Reference Y Note - View Looking ????
Pipe

20
(typ)

T.O.S. EL

45º 1
Support 200
No P29
Max Load

Support
No P30

(200 Min) Support is Identical


to P29 except it is
Opposite hand

Size Dimensions Mark M.T.O. Max Loads (KN)


Code K (Max) M (Min) L No 1 Length Vertical Horizontal
A1 800 1649 10.0 3.0
A2 1000 2132 7.5 2.5
A3 1000 200 1200 UPN 160 2615 5.0 1.5
A4 1400 3098 5.0 1.5
A5 1600 3581 5.0 1.5

Assembly Tag No: - P29 or P30 - XX, Dimension "Y", T.O.S. EL, View looking ????
Detail No Size Code
SUPPORT No P29, P30
SUPPORT TYPE Braced Cantilevers Sheet E19
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
Y Reference
Note - View Pipe
Looking ????

T.O.S. EL

1
= =
Support Max Load (typ)
No P31
4000 (Max)
L

Y Reference
Pipe
Note - View
Looking ????

T.O.S. EL

Support
No P32 20 200 min 4000 (Max)
(Min)
L

200 min Y Reference


Pipe
Note - View
Looking ????

T.O.S. EL

Support
No P33 20 4000 (Max)
(Min)
L

Assembly Tag No: - P31 or P32 or P33 - XX, Dimension "Y", T.O.S. EL, View looking ????
Detail No Size Code
SUPPORT No P31, P32, P33
SUPPORT TYPE Beams Welded to Columns Sheet E20
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Support Size Dim'n Mark M.T.O. Max Loads (KN)


No Code L No 1 Length Vertical Horizontal
A1 2000 HEA 100 2000 8.0 4.0
B1 2000 2000 20.0 10.0
B2 3000 HEA 160 3000 15.0 7.0
P31 B3 4000 4000 10.0 5.0
C1 2000 2000 30.0 20.0
C2 3000 HEA 200 3000 25.0 15.0
C3 4000 4000 20.0 10.0
A1 2000 2000 15.0 4.0
A2 2400 2400 12.0 3.0
A3 2800 2800 10.0 2.5
P32/P33 A4 3200 UPN 200 3200 8.0 2.5
A5 3600 3600 6.0 2.0
A6 4000 4000 6.0 2.0
A7 4400 4400 4.0 1.5
A8 4800 4800 4.0 1.5

SUPPORT No P31, P32, P33


SUPPORT TYPE Beams Welded to Columns (Dimensions) Sheet E21
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

L (4000 Max)
Y
Note - View Reference
Looking Pipe
North or East

T.O.S. EL

1
Max Load (typ)
Support
No P34 = =

Y Reference
Note - View Pipe
Looking
North or East

T.O.S. EL

Support 100 4000 (Max) 100


No P35 L

Y Reference
Note - View 2 Site Trim
Pipe to suit
Looking
North or East

300
T.O.S. EL Max
520

Support 100 4000 (Max) 100 20


No P36 L

Assembly Tag No: - P34 or P35 or P36 - XX, Dimension "Y", T.O.S. EL
Detail No Size Code
SUPPORT No P34, P35, P36
SUPPORT TYPE Beams Welded to Beams Sheet E22
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Support Size Dim'n Mark M.T.O. Mark M.T.O. Max Loads (KN)
No Code L No 1 Length No 2 Length Vertical Horizontal
A1 2000 HEA 100 2000 8.0 4.0
B1 2000 2000 20.0 10.0
B2 3000 HEA 160 3000 15.0 7.0
P34/35 B3 4000 4000 10.0 5.0
C1 2000 2000 30.0 20.0
C2 3000 HEA 200 3000 25.0 15.0
C3 4000 4000 20.0 10.0
A1 2000 2000 15.0 4.0
A2 2400 2400 12.0 3.0
P36 A3 2800 UPN 200 2800 100 x 10 520 10.0 2.5
A4 3200 3200 Angle 8.0 2.5
A5 3600 3600 6.0 2.0
A6 4200 4200 6.0 2.0

SUPPORT No P34, P35, P36


SUPPORT TYPE Beams Welded to Beams (Dimensions) Sheet E23
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

200 Y
Reference (Min) 500 (Max) Note - View
Pipe Looking ????
1

T.O.S. EL

Support
4000 (Max) 100
No P37 Max Load
L

200 Y
Site trim to suit
(Min) 500 (Max) Note - View
Reference 2
Looking ????
Pipe
1
300
T.O.S. EL (Max)

Support
No P38 4000 (Max) 100 20
Max Load
L

200 Y Note - View


Site trim to suit
(Min) Looking ????
Reference
Pipe 2
300 1
T.O.S. EL (Max)

Support
No P39 20
Max Load
4000 (Max) 100
L

Assembly Tag No: - P37 or P38 or P39 - XX, Dimension "Y", T.O.S. EL, View looking ????
Detail No Size Code
SUPPORT No P37, P38, P39
SUPPORT TYPE Cantilevered Beams Sheet E24
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Support Size Dim'n Mark M.T.O. Mark M.T.O. Max Loads (KN)
No Code L No 1 Length No 2 Length Vertical Horizontal
A1 2000 2000 8.0 2.5
A2 2400 HEA 100 2400 8.0 2.5
A3 2800 2800 6.0 2.0
B1 2400 2400 20.0 8.0
B2 2800 2800 20.0 8.0
P37 B3 3200 HEA 160 3200 15.0 6.0
B4 3600 3600 15.0 6.0
C1 4000 4000 25.0 10.0
C2 4400 HEA 200 4400 20.0 10.0
C3 4800 4800 20.0 10.0
A1 2000 2000 7.0 2.0
A2 2400 2400 7.0 2.0
A3 2800 UPN 160 2800 7.0 2.0
P38/39 A4 3200 3200 100 x 10 520 7.0 1.5
A5 3600 3600 Angle 7.0 1.5
B1 4000 4000 12.0 3.0
B2 4400 UPN 200 4400 12.0 2.0
B3 4800 4800 12.0 2.0

SUPPORT No P37, P38, P39


SUPPORT TYPE Cantilevered Beams (Dimensions) Sheet E25
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3
L
L
Reference = = = =
Pipe Y 20 T.O.S. EL

T.O.S. EL 1
H
X X
2
150
1
H 6
Site trim and 15
field weld 3 100mm Bolt
4 5 Penetration into
paving
20
2
U/S Baseplate =
EL 100200
250
Paving =
35
Support No Note - View Looking (Typ)
250 Hole
P41-B/C/D/E/F North or East Dia = 22
Dimension Allowable Bending View X-X
Size Code Notes
H L Moment (KNm) Support No P41-A
A1 300
A2 1000 500 0.5 Max Pipe
A3 750 Size = 2"
Size Code Mark No1 Length Mark No2 Mark No3 Mark No4 Mark No5 (4 Off) Mark No6
A1 70 x 8 1300 250 x 250 Cementitious M20 Nuts M20 threaded rod with M20
A2 Angle 1500 15 Thk Grout (G1) (8 Off) Hilti HY150 resin capsule Washers
3
A3 1800 Plate 0.01m adhesive 280 Long (8 Off)
Size Code Dimension Mark No1 Total Mark No2 Allowable Bending Notes
H L Length Moment (KNm)
B1 300 1200 Pipe
B2 1000 500 HEA 100 1400 Support 4.0
B3 750 1650 Foundat'n
B4 1000 1900 F8N-1
C1 300 2200 Pipe Max Pipe
C2 2000 500 HEA 100 2400 Support 4.0 Size = 4"
C3 750 2650 Foundat'n
C4 1000 2900 F8N-1
D1 300 2140 Pipe
D2 2000 500 HEA 160 2340 Support 8.0
D3 750 2600 Foundat'n
D4 1000 2840 F8N-2
E1 300 3140 Pipe Max Pipe
E2 3000 500 HEA 160 3340 Support 8.0 Size = 4"
E3 750 3600 Foundat'n
E4 1000 3840 F8N-2
F1 300 3100 Pipe
F2 3000 500 HEA 200 3300 Support 12.0
F3 750 3550 Foundat'n
F4 1000 3800 F8N-2
Assembly Tag No: - P41 - XX, Dimension "Y", T.O.S. EL
Detail No Size Code
SUPPORT No P41
SUPPORT TYPE T-Post from new paving Sheet E26
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

L (typ)

= =
T.O.S. EL

H 1

Site trim and


field weld

20 3

U/S Baseplate
EL 100200

Paving

Notes: - 1- Size Codes "B" and "D" shall only be used for Pipe Sizes ≤ 4"

Allowable
Dimension
Size Mark Total Mark Area Mark Bending
Code No 1 Length No 2 (cm²) No 3 Moment
H L
(KNm)
A1 1000 200 HEA 100 1000 12 Thk 400 Pipe 4.0
A2 300 1000 square 900 Support
B1 2000 200 HEA 100 2000 plate 400 Foundat'n 4.0 Note 1
B2 300 2000 900 F8N-1
C1 2000 300 HEA 160 2000 900 Pipe 8.0
C2 450 2000 15 Thk 2025 Support
D1 3000 300 HEA 160 3000 square 900 Foundat'n 8.0 Note 1
D2 450 3000 plate 2025 F8N-2
E1 3000 400 HEA 200 3000 1600 Foundat'n 12.0
E2 550 3000 3025 F8N-2

Assembly Tag No: - P42 - XX, T.O.S. EL


Detail No Size Code
SUPPORT No P42
SUPPORT TYPE Post with Square Plate from new paving Sheet E27
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3
Note - View 20 L
20 L Looking ????
Y Y

T.O.S. EL
T.O.S. EL

1
H
1 X X
2
Site trim
H
and field weld 150
6
2 15
3
4 5 100mm Bolt Penetration
20 into paving
U/S Baseplate
EL 100200
=
250
Paving
=
35
Support No P43-B/C/D/E/F (Typ)
250 Hole
Dia = 22
Note: - 1- This support is not to be used
View X-X
for anchoring pipes
2- The support can not be used Support No P43-A
on lines 6" and above without
consultation with the stress engineer.
Size Code Dimension Allowable Bending Notes
H L Moment (KNm)
A1 1000 250 Max Pipe
A2 500 0.5 Size = 2"
Size Code Mark No1 Length Mark No2 Mark No3 Mark No4 Mark No5 (4 Off) Mark No6
A1 70 x 8 1350 250 x 250 Cementitious M20 Nuts M20 threaded rod with M20
A2 Angle 1550 15 Thk Grout (G1) (8 Off) Hilti HY150 resin capsule Washers
1800 Plate 0.01m3 adhesive 280 Long (8 Off)
Size Code Dimension Mark No1 Total Mark No2 Allowable Bending Notes
H L Length Moment (KNm)
B1 1000 250 HEA 100 1240 Pipe 4.0
B2 500 1480 Support
C1 2000 250 HEA 100 2230 Foundat'n 4.0 Max Pipe
C2 500 2480 F8N-1 Size = 4"
D1 2000 250 HEA 160 2200 Pipe 8.0
D2 500 2450 Support
E1 3000 250 HEA 160 3200 Foundat'n 8.0 Max Pipe
E2 500 3450 F8N-2 Size = 4"
F1 3000 250 HEA 200 3180 Foundat'n 12.0
F2 500 3430 F8N-2
Assembly Tag No: - P43 - XX, Dimension "Y", T.O.S. EL, View looking ????
Detail No Size Code
SUPPORT No P43
SUPPORT TYPE Cantilevered-Post from new paving Sheet E28
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3

L
K M K
Reference Y
Pipe

20
T.O.S. EL

Site trim and


field weld
1
H Note - View Looking
North or East

X X
2

150

6 15

3 100mm Bolt
4 5 Penetration into
paving
=
250
=
35
(Typ) Hole
250
Dia = 22
View X-X
Note: - 1- The support shall be
Support No P44-A used for pipes ≤ 2"

Size Code Dimension Allowable Bending Notes


H L M K Moment (KNm)
A1 1000 1100 1000 50 Max Pipe
A2 1000 1500 1000 250 0.5 Size = 2"
Size Code Mark No1 Length Mark No2 Mark No3 Mark No4 Mark No5 Mark No6
(2 Off) (16 Off) (8 Off) (16 Off)
A1 70 x 8 3100 250 x 250 Cementitious M20 threaded rod with M20
A2 Angle 3500 15 Thk Grout (G1) M20 Nuts Hilti HY150 resin capsule Washers
Plate 0.02m3 adhesive 280 Long

Assembly Tag No: - P44 - XX, Dimension "Y", T.O.S. EL


Detail No Size Code
SUPPORT No P44
SUPPORT TYPE Goal Post from new paving Sheet E29
PIPE SIZE ½" - 2"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
L
K M K
Reference
Y
Pipe

T.O.S. EL

Note - View Looking 1


North or East H
Site trim and
field weld

2
U/S Baseplate
EL 100200
Paving 20

Allowable
Dimension
Size Mark Total Mark Bending
Code No 1 Length No 2 Moment
H L K M
(2 Off) (KNm)
B1 1300 150 3110 Support
B2 1000 1600 300 1000 HEA 100 3410 Foundat'n 4.0
B3 2000 500 3810 F8N-1
C1 1400 100 1200 3100
C2 1000 1700 250 3400
C3 2000 250 1500 3700 Pipe
C4 2500 500 HEA 160 4200 Support 8.0
C5 1400 100 1200 5100 Foundat'n
C6 2000 1700 250 5400 F8N-2
C7 2000 250 1500 5700
C8 2500 500 6200
D1 2000 150 1700 3620
D2 1000 2500 250 2000 4120
D3 3000 500 4620 Pipe
D4 2000 150 1700 5620 Support
D5 2000 2500 250 2000 HEA 200 6120 Foundat'n 12.0
D6 3000 500 6620 F8N-2
D7 2000 150 1700 7620
D8 3000 2500 250 2000 8120
D9 3000 500 8620
Assembly Tag No: - P44 - XX, Dimension "Y", T.O.S. EL
Detail No Size Code
SUPPORT No P44
SUPPORT TYPE Goal Post from new paving Sheet E30
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

T.O.S. EL

Site trim and


field weld

20 2
U/S Baseplate
EL 100200

Paving

For dimension "H" see Table below


Note: -
Allowable
Size Dim'n Mark Total Mark No 2 Bending
Code H No 1 Length Moment
(KNm)
A 1000 HEA 100 1000 Pipe Support 4.0
B 2000 HEA 100 2000 Foundation F8N-1 4.0
C 2000 HEA 160 2000 Pipe Support 8.0
D 3000 HEA 160 3000 Foundation F8N-2 8.0

Assembly Tag No: - P45 - X, T.O.S. EL


Detail No Size Code
SUPPORT No P45
SUPPORT TYPE Post from new paving Sheet E31
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

L
K M
Reference
Y
Pipe

T.O.S. EL

Site trim and


field weld

20 2 Note - View Looking ????


U/S Baseplate
EL 100200

Paving

Allowable
Dimension
Size Mark Total Mark Bending
Code No 1 Length No 2 Moment
H L K M
(KNm)
A1 1000 1600 100 2500 Pipe
A2 2000 500 1500 HEA 160 2900 Support 8.0
A3 2000 1600 100 3500 Foundat'n
A4 2000 500 3900 F8N-2
B1 1000 2120 120 3020
B2 2500 500 3400 Pipe
B3 2000 2120 120 2000 HEA 200 4020 Support 12.0
B4 2500 500 4400 Found'n
B5 3000 2120 120 5020 F8N-2
B6 2500 500 5400

Assembly Tag No: - P46 - XX, Dimension "Y", T.O.S. EL, View looking ????
Detail No Size Code
SUPPORT No P46
SUPPORT TYPE Welded Cantilevered Post from new paving Sheet E32
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
L
Reference = = Note - View Looking
Pipe Y
North or East

Support No
T.O.S. EL P1-A
L
= =
Support No 20
P1-B/C/D/E/F
1
H
1
H
2 Site trim and 2
field weld
20

U/S Baseplate
EL 100200 (typ) Existing Grade

Allowable
Dimension
Total Bending
Size Code Mark No1 Mark No2 Notes
Length Moment
H L
(KNm)
A1 300 70 x 8 1300 Support For use only on
A2 1000 500 Angle 1500 Foundat'n 0.5 Pipe Sizes ≤ 2"
A3 750 1800 F9-1
B1 300 1200 Pipe
B2 1000 500 HEA 100 1400 Support 4.0
B3 750 1650 Foundat'n
B4 1000 1900 F9-1
C1 300 2200 Pipe
C2 2000 500 HEA 100 2400 Support 4.0 For use only on
C3 750 2650 Foundat'n Pipe Sizes ≤ 4"
C4 1000 2900 F9-1
D1 300 2140 Pipe
D2 2000 500 HEA 160 2340 Support 8.0
D3 750 2600 Foundat'n
D4 1000 2840 F9-2
E1 300 3140 Pipe
E2 3000 500 HEA 160 3340 Support 8.0 For use only on
E3 750 3600 Foundat'n Pipe Sizes ≤ 4"
E4 1000 3840 F9-2
F1 300 3100 Pipe
F2 3000 500 HEA 200 3300 Support 8.0
F3 750 3550 Foundat'n
F4 1000 3800 F9-2
Assembly Tag No: - P51 - XX, Dimension "Y", T.O.S. EL
Detail No Size Code
SUPPORT No P51
SUPPORT TYPE T-Post for un-paved areas Sheet E33
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

L (typ)

= =
T.O.S. EL

H 1

Site trim and


field weld

20 3

U/S Baseplate
EL 100200
Existing Grade

Notes: - 1- Size Codes "B" and "D" shall only be used for Pipe Sizes ≤ 4"
Allowable
Dimension
Size Mark Total Mark Area Mark Bending
Code No 1 Length No 2 (cm²) No 3 Moment
H L
(KNm)
A1 1000 200 HEA 100 1000 12 Thk 400 Pipe 4.0
A2 300 1000 square 900 Support
B1 2000 200 HEA 100 2000 plate 400 Foundat'n 4.0 Note 1
B2 300 2000 900 F9-1
C1 2000 300 HEA 160 2000 900 Pipe 8.0
C2 450 2000 15 Thk 2025 Support
D1 3000 300 HEA 160 3000 square 900 Foundat'n 8.0 Note 1
D2 450 3000 plate 2025 F9-2
E1 3000 400 HEA 200 3000 1600 Foundat'n 8.0
E2 550 3000 3025 F9-2

Assembly Tag No: - P52 - XX, T.O.S. EL


Detail No Size Code
SUPPORT No P52
SUPPORT TYPE Post with Square Plate for un-paved areas Sheet E34
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
20 L
Y
Note - View Looking ????

T.O.S. EL 20 L
Y

T.O.S. EL
1
20

H
Site trim and field
1
weld to existing
H
structure

2
20
U/S Baseplate
EL 100200 (typ)
2
Existing Grade

Support No P3-B/C/D/E/F Support No P3-A


Note: - 1- This support is not to be used for anchoring pipes
2- The support can not be used on lines 6" and above without consultation with
the stress engineer.
Allowable
Dimension
Size Mark Total Mark Bending
Notes
Code No 1 Length No 2 Moment
H L
(KNm)
A1 1000 250 70 X 8 1350 0.5 For use only on
A2 500 Angle 1550 Pipe Pipe Sizes ≤ 2"
B1 1000 250 HEA 100 1220 Support 4.0
B2 500 1470 Foundat'n
C1 2000 250 HEA 100 2220 F9-1 4.0 For use only on
C2 500 2470 Pipe Sizes ≤ 4"
D1 2000 250 HEA 160 2190 Pipe 8.0
D2 500 2440 Support
E1 3000 250 HEA 160 3190 Foundat'n 8.0 For use only on
E2 500 3440 F9-2 Pipe Sizes ≤ 4"
F1 3000 250 HEA 200 3170 Foundat'n 8.0
F2 500 3420 F9-2
Assembly Tag No: - P53 - XX, Dimension "Y", T.O.S. EL, View looking ????
Detail No Size Code
SUPPORT No P53
SUPPORT TYPE Cantilevered-Post for un-paved areas Sheet E35
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

SUPPORT DELETED
L
K M K
Reference Y
Pipe

20
T.O.S. EL

1
H Note - View Looking
North or East
Site trim and
field weld

200 (Ref) 200 (Ref)


Existing
Grade

Note: - 1- The support shall be used for pipes ≤ 2"

Size Dimension Mark Total Mark No 2


Code H L M K No 1 Length (2 Off)
A1 SUPPORT DELETED
A2

Assembly Tag No: - P54 - XX, Dimension "Y", T.O.S. EL


Detail No Size Code
SUPPORT No P54 SUPPORT DELETED
SUPPORT TYPE Goal Post for un-paved areas Sheet E36
PIPE SIZE ½" - 2"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3

L
K M K
Reference Y
Pipe

T.O.S. EL

Note - View Looking 1


North or East H
Site trim and
field weld
2
U/S Baseplate
EL 100200 (typ) 20

Existing Grade

Allowable
Dimension
Size Mark Total Mark Bending
Code No 1 Length No 2 Moment
H L K M
(2 Off) (KNm)
Support
B2 1000 1620 60 1500 HEA 100 3430 Foundat'n 4.0
B3 2000 250 3810 F9-1
C3 1000 2000 100 1800 3700 Pipe
C4 2500 350 HEA 160 4200 Support 8.0
C7 2000 2000 100 1800 5700 Foundat'n
C8 2500 350 6200 F9-2
D3 1000 3000 500 2000 4620 Pipe
D6 2000 3000 500 2000 HEA 200 6620 Support 8.0
D7 2100 150 1800 7720 Foundat'n
D8 3000 2500 250 2000 8120 F9-2
D9 3000 500 8620

Assembly Tag No: - P54 - XX, Dimension "Y", T.O.S. EL


Detail No Size Code
SUPPORT No P54
SUPPORT TYPE Goal Post for un-paved areas Sheet E37
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3

T.O.S. EL

H
Site trim and
field weld

20

U/S Baseplate
EL 100200
Existing Grade

Note: - For dimension "H" see Table below

Allowable
Size Dim'n Mark Total Mark No 2 Bending
Code H No 1 Length Moment
(KNm)
A 1000 HEA 100 1000 Pipe Support 4.0
B 2000 HEA 100 2000 Foundation F9-1 4.0
C 2000 HEA 160 2000 Pipe Support 8.0
D 3000 HEA 160 3000 Foundation F9-2 8.0

Assembly Tag No: - P55 - X, T.O.S. EL


Detail No Size Code
SUPPORT No P55
SUPPORT TYPE Post for un-paved areas Sheet E38
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3

L
K M
Reference
Y
Pipe

T.O.S. EL

Site trim and


field weld

2 Note - View Looking ????


20

U/S Baseplate
EL 100200
Existing Grade

Allowable
Dimension
Size Mark Total Mark Bending
Code No 1 Length No 2 Moment
H L K M
(KNm)
B1 1000 2120 120 3020
B2 2500 500 3400 Pipe
B3 2000 2120 120 2000 HEA 200 4020 Support 8.0
B4 2500 500 4400 Foundat'n
B5 3000 2120 120 5020 F9-2
B6 2500 500 5400

Assembly Tag No: - P56 - XX, Dimension "Y", T.O.S. EL, View looking ????
Detail No Size Code
SUPPORT No P56
SUPPORT TYPE Welded Cantilevered Post for un-paved areas Sheet E39
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3
NOTE - TYPICAL SUPPORT FOR UTILITY
STATIONS OR SIMILAR PIPING
L
Reference = = X
Pipe Y A

T.O.S. EL
10

H 1
Support No P60-A Site Trim shear
Site trim and field Support from Existing lug if it clashes
weld to existing Steelwork with vertical
structure steel section

For alternative welding A


View A-A
arrangements refer to
Support No P2

Support No P60-B 1
Support from grade. 2
Steelwork sizes and dimensions as 60-A, but
the support includes a baseplate BP-2"

Size Code Dimension Mark No1 Total Mark No2 Allowable Bending Notes
H L Length Moment (KNm)
A1 500 2510
A2 2000 750 HEA 100 2760 1.0 Max pipe
A3 1000 3010 size 2"
A4 1300 3310
B1 500 2510 Base
B2 2000 750 HEA 100 2760 Plate 1.0 Max pipe
B3 1000 3010 BP-2" size 2"
B4 1300 3310
Assembly Tag No: - P60 - XX, Dimension "X", Dimension "Y", T.O.S. EL,
Detail No Size Code
SUPPORT No P60
SUPPORT TYPE T-Post from structure or grade for Utility Stations Sheet E40
PIPE SIZE ½" - 2"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
L
= =
Utility Pipe

20

SB-9 (ref only) Field Weld


U-Bolt shall be
1
bolted tight so
that it grips Handrailing
the pipe 1300
1 (typ)

Platform Site trim vertical 2000


grating section to suit,
and field weld

1
Platform
Support steel

20

100 20

400

Weld Angle to beam/channel


face or underside of section
dependant on platform design.

Size Code No of Dimension Mark No1 Total


Pipes L Length
A1 1 300 2700 200 min
A2 2 500 70 x 8 2900
A3 3 700 Angle 3100
A4 4 900 3300

Assembly Tag No: - P61 - XX,


Detail No Size Code
SUPPORT No P61
SUPPORT TYPE Support for Utility Stations from platforms Sheet E41
PIPE SIZE ½" - 2"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
NOTE - THESE SUPPORTS SHALL BE
USED FOR UTILITY STATIONS ONLY

Existing Column
Plan View
A
Field
T weld
1

A Reference
Y Pipe
L
Field Trim Length as required

Site Trim shear


lug if it clashes
with vertical
steel section

SB7 (Ref)
T.O.S. EL

View A-A

Size Code Dimension Mark No1 Total


L Length
A1 600 600
A2 800 HEA 100 800
A3 1000 1000
A4 1200 1200

Assembly Tag No: P62 - XX Dimension "Y"

Detail No Size Code


SUPPORT No P62
SUPPORT TYPE Cantilever support for utility stations Sheet E42
PIPE SIZE ½" - 2"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Existing Column
Plan View
A
Field
weld
1

T
A Reference
Y Pipe
L
Field Trim Length as required

SB8 (Ref)

UG (Ref)

T.O.S. EL

View A-A

Size Code Dimension Mark No1 Total


L Length
A1 800 800
A2 1000 UPN100 1000
A3 1200 1200
A4 1500 1500

Assembly Tag No: P63 - XX Dimension "Y"

Detail No Size Code


SUPPORT No P63
SUPPORT TYPE Support for steam trap manifolds Sheet E43
PIPE SIZE ½" - 2"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3

10
2 3 1
4
30
Typ

Typ
30

250
Field
Weld
250 24 dia Holes
(4 off)

175 30 Ref Cantilever Support


No P21,P22,P23
Hole Depth = 175.
Size Codes A or B only
Insert HVU Resin
(70 x 8 Angle, HEA 100,
Capsule suitable for
UPN 100)
M20 threaded bar

Size Allowable Load


Code (KNm)
A 4.0

Size Mark No.1 Area Mark No.2 Mark No.3 Mark No.4 Length
Code cm2 (4 Off) (4 Off) (4 Off)
10 Thk. M20 M20 M20 Threaded Bar &
A Square 625 Washer Nuts HVU Resin Capsule 220
Plate

Assembly Tag No: - P20 - X


Detail No Size Code
SUPPORT No P20
SUPPORT TYPE Base Plate for Cantilever to Concrete Sheet E44
PIPE SIZE 2" - 6"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3
L
Reference = = Note - View Looking
Pipe Y
North or East

Support No
T.O.S. EL P71-A
L
= =
Support No 20
P71-B/C/D/E/F
1
H
1
Site trim and H
field weld
20 3
U/S Baseplate
EL 200 above Local Grade
Local Grade (typ)
2

Allowable
Dimension
Total Bending
Size Code Mark No1 Mark No2 Mark No3 Notes
Length Moment
H L
(KNm)
A1 300 70 x 8 1300 Support F8N-4 For use
A2 1000 500 Angle 1500 Foundat'n Size Negligible on Pipes
A3 750 1800 F9-10 Code A Sizes ≤ 2"
B1 300 1200 Pipe
B2 1000 500 HEA 100 1400 Support Pipe 4.0
B3 750 1650 Foundat'n Support
B4 1000 1900 F9-6 Foundat'n
C1 300 2200 Pipe F8N4 For use
C2 2000 500 HEA 100 2400 Support Size 4.0 on Pipes
C3 750 2650 Foundat'n Code B Sizes ≤ 4"
C4 1000 2900 F9-6
D1 300 2140 Pipe
D2 2000 500 HEA 160 2340 Support 8.0
D3 750 2600 Foundat'n
D4 1000 2840 F9-9 Pipe
E1 300 3140 Pipe Support For use
E2 3000 500 HEA 160 3340 Support Foundat'n 8.0 on Pipes
E3 750 3600 Foundat'n F8N4 Sizes ≤ 4"
E4 1000 3840 F9-9 Size
F1 300 3100 Pipe Code C
F2 3000 500 HEA 200 3300 Support 8.0
F3 750 3550 Foundat'n
F4 1000 3800 F9-9
Assembly Tag No: - P71 - XX, Dimension "Y", T.O.S. EL
Detail No Size Code
SUPPORT No P71
SUPPORT TYPE T-Post for un-paved areas Sheet E45
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3
L (typ)

= =
T.O.S. EL

H 1

Site trim and


field weld

20
3
U/S Baseplate
EL 200 above
Local Grade (typ) Local Grade

Notes: - 1- Size Codes "B" and "D" shall only be used for Pipe Sizes ≤ 4"

Size Dimension Mark Total Mark Area Mark Mark


Code H L No 1 Length No 2 (cm²) No 3 No 4
A1 1000 200 HEA 100 1000 12 Thk 400 Pipe Foundat'n
A2 300 1000 square 900 Support F8N4
B1 2000 200 HEA 100 2000 plate 400 Foundat'n Size
B2 300 2000 900 F9-6 Code B
C1 2000 300 HEA 160 2000 900 Pipe Pipe
C2 450 2000 15 Thk 2025 Support Support
D1 3000 300 HEA 160 3000 square 900 Foundat'n Foundat'n
D2 450 3000 plate 2025 F9-9 F8N4
E1 3000 400 HEA 200 3000 1600 Foundat'n Size
E2 550 3000 3025 F9-9 Code C

Size Allowable Bending


Code Moment (KNm)
A, B 4.0
C,D,E 8.0

Assembly Tag No: - P72 - XX, T.O.S. EL


Detail No Size Code
SUPPORT No P72
SUPPORT TYPE Post with Square Plate for un-paved areas Sheet E46
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3
20 L
Y
Note - View Looking ????

T.O.S. EL 20 L
Y

T.O.S. EL
1
20

H
Site trim and field
1
weld to existing
H
structure
3
3
20
U/S Baseplate
EL 200 above
Local Grade (typ) Local Grade

Support No P73-B/C/D/E/F Support No P73-A


Note: - 1- This support is not to be used for anchoring pipes
2- The support can not be used on lines 6" and above without consultation with
the stress engineer.
Allowable
Dimension
Size Mark Total Mark Mark Bending Notes
Code No 1 Length No 2 No 3 Moment
H L
(KNm)
A1 1000 250 70 x 8 1350 Pipe Fnd. F8N4 Negligible For Pipes
A2 500 Angle 1550 F9-10 Code A Sizes ≤ 2"
B1 1000 250 HEA 100 1220 Pipe Foundat'n 4.0
B2 500 1470 Support F8N4
C1 2000 250 HEA 100 2220 Foundat'n Size 4.0 For Pipes
C2 500 2470 F9-6 Code B Sizes ≤ 4"
D1 2000 250 HEA 160 2190 Pipe Pipe 8.0
D2 500 2440 Support Support
E1 3000 250 HEA 160 3190 Foundat'n Foundat'n 8.0 For Pipes
E2 500 3440 F9-9 F8N4 Sizes ≤ 4"
F1 3000 250 HEA 200 3170 Foundat'n Size 8.0
F2 500 3420 F9-9 Code C
Assembly Tag No: - P73 - XX, Dimension "Y", T.O.S. EL, View looking ????
Detail No Size Code
SUPPORT No P73
SUPPORT TYPE Cantilevered-Post for un-paved areas Sheet E47
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3
L
K M K
Reference Y
Pipe

T.O.S. EL

Note - View Looking 1


North or East H
Site trim and
field weld
3
U/S Baseplate
EL 200 above 20
Local Grade (typ) Local Grade

Size Dimension Mark Total Mark No 2 Mark No 3


Code H L K M No 1 Length (2 Off) (2 Off)
Support F8N4
B2 1000 1620 60 1500 HEA 100 3420 Foundat'n Size
B3 2000 250 3800 F9-6 Code B
C3 1000 2000 100 1800 3680 Pipe
C4 2500 350 HEA 160 4180 Support Pipe
C7 2000 2000 100 1800 5680 Foundat'n Support
C8 2500 350 6180 F9-9 Foundat'n
D3 1000 3000 500 2000 4600 Pipe F8N4
D6 2000 3000 500 2000 HEA 200 6600 Support Size
D7 2100 150 1800 7700 Foundat'n Code C
D8 3000 2500 250 2000 8100 F9-9
D9 3000 500 8600

Size Allowable Bending


Code Moment (KNm)
B 4.0
C,D 8.0

Assembly Tag No: - P74 - XX, Dimension "Y", T.O.S. EL


Detail No Size Code
SUPPORT No P74
SUPPORT TYPE Goal Post for un-paved areas Sheet E48
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3

T.O.S. EL

H
Site trim and
field weld

20

U/S Baseplate
EL 200 above
Local Grade
Local Grade (typ)

Note: - For dimension "H" see Table below

Allowable
Size Dim'n Mark Total Mark No 2 Mark No 3 Bending
Code H No 1 Length Moment
(KNm)
A 1000 HEA 100 1000 Pipe Support Support Foundation 4.0
B 2000 HEA 100 2000 Foundation F9-6 F8N4 Size Code B 4.0
C 2000 HEA 160 2000 Pipe Support Support Foundation 8.0
D 3000 HEA 160 3000 Foundation F9-9 F8N4 Size Code C 8.0

Assembly Tag No: - P75 - X, T.O.S. EL


Detail No Size Code
SUPPORT No P75
SUPPORT TYPE Post for un-paved areas Sheet E49
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3

L
K M
Reference
Y
Pipe

T.O.S. EL

Site trim and


field weld

3 Note - View Looking ????


20

U/S Baseplate
EL 200 above
Local Grade
Local Grade (typ)

Size Dimension Mark Total Mark Mark


Code H L K M No 1 Length No 2 No 3
B1 1000 2120 120 3020 Pipe
B2 2500 500 3400 Pipe Support
B3 2000 2120 120 2000 HEA 200 4020 Support Foundat'n
B4 2500 500 4400 Foundat'n F8N4
B5 3000 2120 120 5020 F9-9 Size
B6 2500 500 5400 Code C

Size Allowable Bending


Code Moment (KNm)
B 8.0

Assembly Tag No: - P76 - XX, Dimension "Y", T.O.S. EL, View looking ????
Detail No Size Code
SUPPORT No P76
SUPPORT TYPE Welded Cantilevered Post for un-paved areas Sheet E50
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0
1000 Site drill angle and
Guide Pipes with
= =
U-Bolt Guide
Y No UG301 (ref)
Reference
Pipe

20

1
800
Site Trim and field
Baseplate shall weld to suit slope in
rest on floor of sump
Caustic Sump 2

300 =

500

= =

800

Size Code Mark Total Mark Area NOTE-


No 1 Length No 2 (cm²) Mark Nos 1 & 2 (base plate and angle)
A1 70 x 8 2200 15 Thk 4000 shall be painted with an epoxy
Angle Plate paint System AD. The painting shall be
made good after welding and drilling
Assembly Tag No: - P64 - A1, Dimension "Y", of the pipe support

Detail No Size Code


SUPPORT No P64
SUPPORT TYPE T-Post for use in Caustic Sump Sheet E51
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 2

Pipe Support No SB1 Pipe Support No SB2


Guide Anchor

X 1 X 1
2 2

60

X X

1200

=
Site Trim
to suit A
=

10 Dia
Hole
(Typ)
35
View X-X

Pipe Pipe Mark No 1 Length Mark No 2 Size Dimension


Sup't No Size A
½ UG-½ 31
¾ 60 x 6 U-Bolt UG-¾ 37
SB1 1 Angle 1260 Guide UG-1 44
1½ UG-1½ 58
2 UG-2 74
½ UA-½ 29
¾ 60 x 6 U-Bolt UA-¾ 35
SB2 1 Angle 1260 Anchor UA-1 42
1½ UA-1½ 56
2 UG-2 72

Assembly Tag No: - SB1 or SB2 - X


Detail No Pipe Size
SUPPORT No SB1, SB2
SUPPORT TYPE Base Guide/Support from Steel for Horizontal Pipes Sheet F1
PIPE SIZE ½" - 2"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 4
Pipe Support No SB3 - Guide Pipe Support No SB4 - Anchor
X X
U-Bolt to be raised
1 if paving settles to
ensure pipe remains
horizontal
200 1
2 2

Slotted
1200
X Holes (4 Off)
X
Site Trim to suit
and Field Weld 60

3
35

10 25
5 (typ)
Pipe =
CL A
4 =

25
20
= (Typ)
35 View X-X
120
=
22 Dia Pipe Pipe Mark No 1 Length
Hole Sup't No Size
= = ½
¾ 60 x 6
120
SB3 1 Angle 1400

2
½
NOTES 1- For General Notes refer to Drawing ¾ 60 x 6
Nos. 60-0000-Q-STD-0010-01 and 02 SB4 1 Angle 1400

2
Pipe Pipe Mark No 2 Size Mark No 3 Area Mark No 4 Dimension
Sup't No Size (") (1 Off) (cm²) (1 Off) A
½ UG-½ 31
¾ U-Bolt UG-¾ 10 Thk M 20 threaded rod 37
SB3 1 Guide UG-1 Plate 144 with Hilti HY 150 resin 44
1½ UG-1½ capsule adhesive 58
2 UG-2 170 Long. (Hilti 74
½ UA-½ HIT-ICE resin to be 29
¾ U-Bolt UA-¾ 10 Thk used if the installation 35
SB4 1 Anchor UA-1 Plate 144 temperature 42
1½ UA-1½ is below -5°C) 56
2 UA-2 72
Assembly Tag No: - SB3 or SB4 - X Mark No 5
Cementitious Grout
Detail No Pipe Size (G1) 0.005m3
SUPPORT No SB3, SB4
SUPPORT TYPE Base Guide/Support from Grade for Horizontal Pipes Sheet F2
PIPE SIZE ½" -2"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 2

240 60 Y A
10
= =
X X

45

35

Y 10 Dia Hole
in Angle (Typ)
2 View X-X

1200 1 150

Site Trim to suit


and Field Weld 50

View Y-Y

Pipe Mark No 1 Length Mark No 2 Size Mark Area Dimension


Size (1 Off) No 3 (cm²) A
½ UA-½ 29
¾ 60 x 6 U-Bolt UA-¾ 6 Thk 35
1 Angle 1545 Anchor UA-1 Plate 75 42
1½ UA-1½ 56
2 UA-2 72

Assembly Tag No: - SB5 - X


Detail No Pipe Size
SUPPORT No SB5
SUPPORT TYPE Base Support from Steel for Vertical Pipes Sheet F3
PIPE SIZE ½" - 2"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 4

240 60 Y A
10
= =
X X

45

35

Y 10 Dia Hole
in Angle (Typ)
2 View X-X
1
1200 150

Site Trim to suit


Z and Field Weld
Z 50

3
5
25 Grout
(Min) View Y-Y

Shim pipe support


6
if paving settles
4 20
(Typ)
Existing =
Paving
120
= 22 Dia
Hole
NOTES 1- For General Notes refer
to Drawing Nos. = = View Z-Z
60-0000-Q-STD-0010-01
120
and 02
Pipe Mark No 1 Mark No 2 Size Mark No 3 Mark No 4 Mark No 5 Dimension
Size (1 Off) (1 Off) A
½ 60 x 6 UA-½ 10 Thk M 20 threaded rod 6 Thk 29
¾ Angle U-Bolt UA-¾ Plate with Hilti HY 150 resin Plate 35
1 Anchor UA-1 capsule adhesive 42
1½ Length UA-1½ Area = 170 Long. (Hilti Area = 56
2 =1545 UA-2 144 cm² HIT-ICE resin to be 75 cm² 72
Assembly Tag No: - SB6 - X used if the installation Mark No 6
temperature Cementitious Grout
Detail No Pipe Size is below -5°C) (G1) 0.01m
3

SUPPORT No SB6
SUPPORT TYPE Base Support from Grade for Vertical Pipes Sheet F4
PIPE SIZE ½" - 2"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 2

150

50

Elevation
1

Existing Steel

3 2

X X

10 Dia
Hole (Typ)

Plan
A B

=
View X-X

Pipe Mark Area Mark Length Mark No 3 Size Dimension


Size No 1 (cm²) No 2 (1 Off) A B
½ 70 UG-½ 31 70
¾ 6 Thk 60 x 6 75 U-Bolt UG-¾ 37 75
1 Plate 75 Angle 85 Guide UG-1 44 85
1½ 100 UG-1½ 58 100
2 120 UG-2 74 120

Assembly Tag No: - SB7 - X


Detail No Pipe Size
SUPPORT No SB7
SUPPORT TYPE Support and Guide for Vertical Pipes Sheet F5
PIPE SIZE ½" - 2"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 2

150

50

Pipe Mark Area


Size No 1 (cm²)
½
¾ 6 Thk
1 Plate 75

2

Assembly Tag No: - SB8 - X


Detail No Pipe Size
SUPPORT No SB8
SUPPORT TYPE Support for Vertical Pipes Sheet F6
PIPE SIZE ½" - 2"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 2

X X

Elevation

Existing Steel

10 Dia
Hole (Typ) 1

2
=

Plan
A B

=
View X-X

Pipe Mark No 1 Length Mark No 2 Size Dimension


Size (1 Off) A B
½ 70 UG-½ 31 70
¾ 60 x 6 75 U-Bolt UG-¾ 37 75
1 Angle 85 Guide UG-1 44 85
1½ 100 UG-1½ 58 100
2 120 UG-2 74 120

Assembly Tag No: - SB9 - X


Detail No Pipe Size
SUPPORT No SB9
SUPPORT TYPE Guide for Vertical Pipes Sheet F7
PIPE SIZE ½" - 2"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 2

Pipe Support No SB101 Pipe Support No SB102


Guide Anchor

X 1 X 1
2 2

80

X X

1200

=
Site Trim
to suit A
=

Hole
Dia = D
35
View X-X

Pipe Pipe Mark No 1 Length Mark No 2 Size Dimension Hole Dia


Sup't No Size A D
½ Insulated U-Bolt ½ 37
¾ 60 x 6 Guide for Stainless ¾ 43 8
SB101 1 Angle 1280 Steel Pipes. 1 50
1½ 1½ 75 12
2 2 87
½ Insulated U-Bolt ½ 37
¾ 60 x 6 Anchor for Stainless ¾ 43 8
SB102 1 Angle 1280 Steel Pipes. 1 50
1½ 1½ 75 12
2 2 87

Assembly Tag No: - SB101 or SB102 - X


Detail No Pipe Size
SUPPORT No SB101, SB102
SUPPORT TYPE Base Guide/Support from Steel for Horizontal SS Pipes Sheet F8
PIPE SIZE ½" - 2"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 4
Pipe Support No SB103 - Guide Pipe Support No SB104 - Anchor
X
X U-Bolt to be raised
if paving settles to
ensure pipe remains
horizontal
1
1
200 2 2

1200
X Site Trim to suit X Slotted
and Field Weld Holes
4 (4 Off)
3

25 Grout
(Min) 60

150 Existing 35
Paving
10 25
5 (typ)
Pipe =
C A
L =

20 25
= (Typ)
120
35 View X-X
=
22 Dia
Hole Pipe Pipe Mark No 1 Length
= = Sup't No Size
120 SB103 ½-2 60 x 6 1400
Angle
NOTES 1- For General Notes refer to Drawing SB104 ½-2 60 x 6 1400
Nos. 60-0000-Q-STD-0010-01 and 02 Angle
Pipe Pipe Mark No 2 Size Mark No 3 Mark No 4
Dimension Hole Dia
Sup't No Size (") A(1 Off) D
½ Insulated ½ 10 Thk 37
¾ U-Bolt ¾ Plate M 20 threaded rod 43 8
SB103 1 guide for 1 with Hilti HY 150 resin 50
1½ Stain. Stl 1½ Area = capsule adhesive 75 12
2 Pipes 2 144 cm² 170 Long. (Hilti 87
½ Insulated ½ 10 Thk HIT-ICE resin to be 37
¾ U-Bolt ¾ Plate used if the installation 43 8
SB104 1 Anchor for 1 temperature 50
1½ Stain. Stl 1½ Area = is below -5°C) 75 12
2 Pipes 2 144 cm² 87
Assembly Tag No: - SB103 or SB104 - X Mark No 5
Cementitious Grout
Detail No Pipe Size
(G1) 0.005m3
SUPPORT No SB103, SB104
SUPPORT TYPE Base Guide/Anchor from Grade for Horizontal SS Pipes Sheet F9
PIPE SIZE ½" -2"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 2

Hole
240 60 Y A
Dia = D
10
= =
X X

45

35

2 View X-X

1200 1

150

Site Trim to suit


and Field Weld

50

Stainless Steel plate


ASTM-A-240 Type 316
or equivalent

View Y-Y

Pipe Mark No 1 Length Mark No 2 Size Mark Dimension Hole Dia


Size No 3 A D
½ Insulated U-Bolt ½ 5 Thk 37
¾ 60 x 6 Guide for Stainless ¾ SS Plate 43 8
1 Angle 1545 Steel Pipes. 1 50
1½ 1½ Area = 75 12
2 2 75 cm² 87

Assembly Tag No: - SB105 - X


Detail No Pipe Size
SUPPORT No SB105
SUPPORT TYPE Base Support from Steel for SS Vertical Pipes Sheet F10
PIPE SIZE ½" - 2"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 4
240 60 Y Hole A
Dia = D
10
= =
X X

45

35

Y
View X-X
2

1200 1 Shim pipe


150 support
if paving
Z Z Site Trim to suit
settles
and Field Weld
5
4
50
25 Grout
(Min)
View Y-Y
150 3
6
Existing Stainless Steel plate
Paving ASTM-A-240 Type 316
20 or equivalent
(Typ) Pipe Dimension Hole Dia
=
Size A D
120 ½ 37
= ¾ 43 8
22 Dia 1 50
Hole 1½ 75 12
2 87
View Z-Z = =

120 NOTES 1- For General Notes refer to Drawing


Nos. 60-0000-Q-STD-0010-01 and 02
Pipe Mark No 1 Mark No 2 Size Mark No 3 Mark No 4 Mark No 5
Size (1 Off)
½ 60 x 6 Insulated U-Bolt ½ 5 Thk 10 Thk M 20 threaded rod
¾ Angle Guide for Stainless ¾ SS Plate Plate with Hilti HY 150 resin
1 Steel Pipes. 1 capsule adhesive
1½ Length 1½ Area = Area = 170 Long. (Hilti
2 =1545 2 75 cm² 144 cm² HIT-ICE resin to be
Assembly Tag No: - SB106 - X Mark No 6 used if the installation
Cementitious Grout temperature
Detail No Pipe Size 3
(G1) 0.01m is below -5°C)
SUPPORT No SB106
SUPPORT TYPE Base Support from Grade for Vertical SS Pipes Sheet F11
PIPE SIZE ½" - 2"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 3
150
Stainless Steel plate
ASTM-A-240 Type 316
or equivalent

50

Elevation
1

Existing Steel

3 2

X X

Hole
Dia = D

=
A B
=

View X-X
Pipe Mark Area Mark Length Mark No 3 Size
Size No 1 (cm²) No 2
½ 80 Insulated U-Bolt ½
¾ 5 Thk 60 x 6 90 Guide for Stainless ¾
1 SS Plate 75 Angle 100 Steel Pipes. 1
1½ 120 1½
2 140 2

Pipe Dimension Hole Dia


Size A B D
½ 37 80
¾ 43 90 8
1 50 100
1½ 75 120 12
2 87 140
Assembly Tag No: - SB107 - X
Detail No Pipe Size
SUPPORT No SB107
SUPPORT TYPE Support and Guide for Vertical SS Pipes Sheet F12
PIPE SIZE ½" - 2"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 3

Stainless Steel plate


150
ASTM-A-240 Type 316
or equivalent

50

Pipe Mark Area


Size No 1 (cm²)
½
¾ 5 Thk
1 SS Plate 75

2

Assembly Tag No: - SB108 - X


Detail No Pipe Size
SUPPORT No SB108
SUPPORT TYPE Support for Vertical Stainless Steel Pipes Sheet F13
PIPE SIZE ½" - 2"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 2

X X

Elevation

Existing Steel

Hole
Dia = D

2
=
A B
=

View X-X

Pipe Mark No 1 Length Mark No 2 Size Dimension Hole Dia


Size A B D
½ 80 Insulated U-Bolt ½ 37 80
¾ 60 x 6 90 Guide for Stainless ¾ 43 90 8
1 Angle 100 Steel Pipes. 1 50 100
1½ 120 1½ 75 120 12
2 140 2 87 140

Assembly Tag No: - SB109 - X


Detail No Pipe Size
SUPPORT No SB109
SUPPORT TYPE Guide for Vertical Pipes Sheet F14
PIPE SIZE ½" - 2"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 2

C
T

R = 1.5 x T
(typ)
A 1 B

A
B
2

Bolts shall be Hole Dia =


provided with Bolt Dia + 2
a nut and a
locking nut

SUPPORT No PC1, PC2


SUPPORT TYPE 2-Bolt Pipe Clip Sheet F15
PIPE SIZE ½" - 30"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 3

2 Bolt Pipe Clip - Light Load. Pipe Support No PC1

Pipe Mark No 1 Total Mark No 2 Dimensions


Size (2 Off) Length (2 Off) A B C D T
½ 228 32 51 21
¾ 235 M12 x 50 32 51 12 27
1 40 x 6 266 Bolts 38 57 33
1½ Plate 335 51 70 48 6
2 372 57 76 16 60
3 485 M16 x 60 76 96 89
4 606 Bolts 95 119 20 114
5½ 732 113 143 140
6 820 127 157 24 168
8 50 x 10 1006 M20 x 80 159 189 219 10
10 Plate 1215 Bolts 190 226 273
12 1377 216 252 324
14 1489 M24 x 100 235 271 356
16 1647 Bolts 260 296 27 406
18 80 x 15 1857 298 334 457
20 Plate 2019 M30 x 120 324 360 508 15
22 2245 Bolts 357 402 559
24 2423 387 432 34 610
26 100 x 20 2729 M36 x 140 440 494 660
28 Plate 2891 Bolts 466 520 40 711 20
30 3053 492 546 762

2 Bolt Pipe Clip - Heavy Load. Pipe Support No PC2

Pipe Mark No 1 Total Mark No 2 Dimensions


Size (2 Off) Length (2 Off) A B C D T
M20 x 80
3 50 x 10 561 Bolts 85 115 24 89 10
4 Plate 658 M24 x 100 96 132 114
6 876 Bolts 135 171 27 168
8 80 x 15 1034 160 196 219
10 Plate 1291 M30 x 120 200 245 273 15
12 1489 Bolts 235 280 34 324
14 1641 255 309 356
16 1799 280 334 406
18 100 x 20 1957 305 359 457
20 Plate 2115 M36 x 140 330 384 508
22 2333 Bolts 370 424 40 559 20
24 2491 395 449 610
26 2729 440 494 660
28 220 x 20 2891 466 520 711
30 Plate 3053 492 546 762

SUPPORT No PC1, PC2


SUPPORT TYPE 2-Bolt Pipe Clip (dimensions) Sheet F16
PIPE SIZE ½" - 30"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 2

C
T

3 Spacer

R = 1.5 x T E
B
(Typ)
A
1
D

A F
2

Bolts shall be Hole Dia =


provided with Bolt Dia + 2
3 a nut and a
locking nut
Spacer

SUPPORT No PC3, PC4


SUPPORT TYPE 3-Bolt Pipe Clip Sheet F17
PIPE SIZE ½" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 2

3 Bolt Pipe Clip - Light Load. Pipe Support No PC3

Pipe Mark No 1 Total Mark No 2 Mark No 3 Total


Size (2 Off) Length (3 Off) (2 Off) Length
½ 332
¾ 40 x 6 357 M12 x 50 24
1 Plate 400 Bolts
1½ 439 32
2 518 1" Sch 80
3 649 M16 x 80 Pipe 50
4 50 x 10 776 Bolts
6 Plate 1046
8 1210 M20 x 100 76
10 80 x 15 1405 Bolts
12 Plate 1571
14 1743 M24 x 130
16 1909 Bolts 1½"
18 2075 Sch 80 102
20 100 x 20 2253 M30 x 150 Pipe
22 Plate 2459 Bolts
24 2617

Pipe Dimensions
Size A B C D E F T
½ 32 92 21 107 47
¾ 38 95 12 27 110 53
1 44 97 33 117 64 6
1½ 51 102 16 48 124 68
2 54 127 60 149 76
3 76 152 25 89 175 99
4 100 165 114 194 129 10
6 135 216 168 254 173
8 163 241 38 219 279 201
10 192 279 273 317 230
12 220 305 324 343 258 15
14 243 330 356 378 291
16 273 356 406 403 320
18 300 381 51 457 429 348
20 329 406 508 457 380 20
22 365 432 559 489 422
24 390 457 610 514 447

SUPPORT No PC3
SUPPORT TYPE 3-Bolt Pipe Clip, Light Load (Dimensions) Sheet F18
PIPE SIZE ½" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 2

Pipe Mark No 1 Total Mark No 2 Mark No 3 Total


Size (2 Off) Length (3 Off) (2 Off) Length
6 80 x 15 1136 M30 x 120 88
8 Plate 1306 Bolts 1½" Pipe
10 100 x 20 1553 M36 x 160 Sch 80
12 Plate 1713 Bolts 102
14 1869
16 130 x 20 2037
18 Plate 2199 M42 x 180 2" Sch 80
20 2455 Bolts Pipe 114
22 220 x 20 2693
24 Plate 2851

Pipe Dimensions
Size A B C D E F T
6 143 229 44 168 279 193 15
8 172 254 219 305 223
10 214 305 273 356 265
12 240 330 51 324 381 291
14 262 356 356 413 319
16 292 381 406 438 349 20
18 317 406 57 457 464 375
20 353 457 508 521 417
22 393 483 559 559 469
24 418 508 610 584 494

SUPPORT No PC4
SUPPORT TYPE 3-Bolt Pipe Clip, Heavy Load (Dimensions) Sheet F19
PIPE SIZE 6" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 3

C
T

R = 1.5 x T
(typ)
A B
1
D D

3
A
B

Bolts shall be Hole Dia =


provided with Bolt Dia + 2
a nut and a
locking nut

SUPPORT No PC101, PC102


SUPPORT TYPE 2-Bolt Pipe Clip for Stainless Steel pipes Sheet F20
PIPE SIZE ½" - 32"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 3

2 Bolt Pipe Clip - Light Load. Pipe Support No PC101

Pipe Mark No 1 Total Mark No 2 Mark No 3 Dimensions


Size (2 Off) Length (2 Off) (1 Off) A B C D T
½ 266 38 57 33
¾ 272 M12 x 50 38 57 12 39
1 40 x 6 303 Bolts 44 63 45
1½ Plate 372 57 76 60 6
2 410 63 82 16 72
3 523 M16 x 60 82 102 101
4 644 Bolts 101 125 20 126
6 857 Isolation 133 163 180
8 50 x 10 1043 M20 x 80 Strip 165 195 24 231
10 Plate 1253 Bolts 196 232 285 10
12 1415 222 258 336
14 1527 M24 x 100 241 277 368
16 1685 Bolts 266 302 27 418
18 80 x 15 1895 304 340 469
20 Plate 2057 M30 x 120 330 366 520 15
22 2283 Bolts 363 408 571
24 2461 393 438 34 622
26 2753 446 500 660
28 100 x 20 2915 M36 x 140 472 526 40 711 20
30 Plate 3077 Bolts 498 552 762
32 3135 498 552 813

2 Bolt Pipe Clip - Heavy Load. Pipe Support No PC102

Pipe Mark No 1 Total Mark No 2 Mark No 3 Dimensions


Size (2 Off) Length (2 Off) (1 Off) A B C D T
M20 x 80
3 50 x 10 599 Bolts 91 121 24 101 10
4 Plate 696 M24 x 100 102 138 126
6 913 Bolts 141 177 27 180
8 80 x 15 1071 166 202 231
10 Plate 1329 M30 x 120 Isolation 206 251 285 15
12 1527 Bolts Strip 241 286 34 336
14 1679 261 315 368
16 1837 286 340 418
18 100 x 20 1995 M36 x 140 311 365 40 469 20
20 Plate 2153 Bolts 336 390 520
22 2371 376 430 571
24 2529 401 455 622

SUPPORT No PC101, PC102


SUPPORT TYPE 2-Bolt Pipe Clip for Stainless Steel pipes (dimensions) Sheet F21
PIPE SIZE ½" - 32"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 2

C
T

3 Spacer

R = 1.5 x T E
B
(Typ)
A
1
D D
D

A F
2

Bolts shall be Hole Dia =


provided with Bolt Dia + 2
3 a nut and a
locking nut
Spacer

SUPPORT No PC103, PC104


SUPPORT TYPE 3-Bolt Pipe Clip for Stainless Steel pipes Sheet F22
PIPE SIZE ½" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 2

3 Bolt Pipe Clip - Light Load. Pipe Support No PC103

Pipe Mark No 1 Total Mark No 2 Mark No 3 Total


Size (2 Off) Length (3 Off) (2 Off) Length
½ 370
¾ 40 x 6 394 M12 x 50 24
1 Plate 437 Bolts
1½ 476 32
2 556 1" Sch 80
3 687 M16 x 80 Pipe 50
4 50 x 10 814 Bolts
6 Plate 1083
8 1247 M20 x 100 76
10 80 x 15 1443 Bolts
12 Plate 1609
14 1781 M24 x 130
16 100 x 20 1947 Bolts 1½"
18 Plate 2113 Sch 80 102
20 2291 M30 x 150 Pipe
22 HOLD 2516 Bolts
24 2673

Pipe Dimensions
Size A B C D E F T
½ 38 98 33 113 53
¾ 44 101 12 39 116 59
1 50 103 45 123 70 6
1½ 57 108 16 60 130 74
2 60 133 72 155 82
3 82 158 25 101 181 105
4 106 171 126 200 135 10
6 141 222 180 260 179
8 169 247 38 231 285 207
10 198 285 285 323 236
12 226 311 336 349 264 15
14 249 336 368 384 297
16 279 362 418 409 326
18 306 387 51 469 435 354
20 335 412 520 463 386 20
22 374 441 577 498 431
24 399 466 628 523 456

SUPPORT No PC103
SUPPORT TYPE 3-Bolt Pipe Clip for Stainless Steel pipes, Light Load Sheet F23
PIPE SIZE ½" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 2

Pipe Mark No 1 Total Mark No 2 Mark No 3 Total


Size (2 Off) Length (3 Off) (2 Off) Length
6 80 x 15 1173 M30 x 120 88
8 Plate 1343 Bolts 1½" Pipe
10 100 x 20 1610 M36 x 160 Sch 80 102
12 Plate 1770 Bolts
14 1926
16 HOLD 2113
18 2275 M42 x 180 2" Sch 80 114
20 2530 Bolts Pipe
22 HOLD 2768
24 2926

Pipe Dimensions
Size A B C D E F T
6 149 235 44 180 285 199 15
8 178 260 231 311 229
10 223 314 51 291 365 274
12 249 339 342 390 300
14 271 365 374 422 328
16 304 393 430 450 361 20
18 329 418 57 481 476 387
20 365 469 532 533 429
22 405 495 583 571 481
24 430 520 634 596 506

SUPPORT No PC104
SUPPORT TYPE 3-Bolt Pipe Clip for Stainless Steel pipes, Heavy Load Sheet F24
PIPE SIZE 6" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 2

2 Gap
(typ)
1

L 10
Max
T

10 Dia Hole in
D
Existing Steel
C

Pipe Pipe Mark No 1 Developed Mark No 2 Dimension


Size O.D. Length (4 Off) C D L T
½ 21 8 dia 126 31 39
¾ 27 Round 141 37 42
1 34 Bar 159 M 8 Nut 44 8 45 38
1½ 48 195 58 52
2 60 226 70 58
2½ 73 259 83 65

Assembly Tag No: - UG - X


Detail No Pipe Size
SUPPORT No UG
SUPPORT TYPE U-Bolt Guide Sheet F25
PIPE SIZE ½" - 2½"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 2

10
Max
L

T
10 Dia Hole in
Existing Steel

D
2
C

Pipe Pipe Mark No 1 Developed Mark No 2 Dimension


Size O.D. Length (4 Off) C D L T
½ 21 133 29 44
¾ 27 8 dia 148 35 47
1 34 Round 166 M 8 Nut 42 8 50 30
1½ 48 Bar 202 56 57
2 60 233 68 63
2½ 73 266 81 70

Assembly Tag No: - UA - X


Detail No Pipe Size

SUPPORT No UA
SUPPORT TYPE U-Bolt Anchor Sheet F26
PIPE SIZE ½" - 2½"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 2

Clevis pin
with split pins
E

C
H
(Typ)
J A

Note: - CLR - Right hand thread clevis


CLL - Left hand thread clevis

Pipe Sup't Sling Rod A B C E F


No Dia D
CL-12 12 30 19 10 82 32
CL-16 16 45 33 10 68 32
CL-20 20 45 33 10 68 32
CL-24 24 65 38 12 63 32
CL-30 30 65 38 12 63 32
CL-36 36 70 45 12 152 41
CL-42 42 90 51 12 152 44

Pipe Sup't Sling Rod G H J L Max


No Dia D Load (KN)
CL-12 12 12 14 38 55 5.0
CL-16 16 16 18 50 65 10.0
CL-20 20 20 22 50 65 15.0
CL-24 24 24 26 58 80 23.0
CL-30 30 30 32 58 80 35.0
CL-36 36 36 39 80 100 53.0
CL-42 42 42 45 85 105 73.0

SUPPORT No CLL, CLR


SUPPORT TYPE Clevis Sheet F27
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 2

R.H. Thread C
Locknut

L 150

L.H. Thread D
Locknut

Pipe Sup't Sling Rod B C L Max


No Dia D Load (KN)
TB-12 12 20 31 190 5.0
TB-16 16 26 41 202 10.0
TB-20 20 32 49 214 15.0
TB-24 24 39 59 228 23.0
TB-30 30 53 67 256 35.0
TB-36 36 58 78 266 53.0
TB-42 42 68 92 286 73.0

SUPPORT No TB
SUPPORT TYPE Turnbuckle Sheet F28
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 2

OC
OA
NOTE
WENL- Left hand thread
WENR- Right hand thread

F B
M

Note: - 1- WENL - Left hand thread Weldless Eye Nut


WENR - Right hand thread Weldless Eye Nut
2- Minimum Length of Thread Engagement equals Diameter of Sling Rod.
3- Variations on dimensions are acceptable provided the load bearing requirements are
met.

Pipe Sup't Sling Rod B C K M F D Max


No Dia A Load (KN)
WEN-12 12 9 38 18 73 16 30 5.0
WEN-16 16 13 38 18 73 20 30 10.0
WEN-20 20 16 45 25 102 25 44 15.0
WEN-24 24 19 50 28 124 26 50 23.0
WEN-30 30 29 70 40 149 44 70 35.0
WEN-36 36 29 70 40 149 44 70 53.0
WEN-42 42 30 80 45 180 46 100 73.0

SUPPORT No WENL, WENR


SUPPORT TYPE Weldless Eye Nut Sheet F29
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 2

Support No R-A Support No R-B Support No R-C


Rod for Non-Adjustable Rod for Adjustable Rod for Trapeze
Hangers Hangers Hangers

1 1

1700

2000 3000

R.H. Thread
R.H. Thread R.H. Thread

L.H. Thread

300
2

D D
D

Pipe Sup't Sling Rod Mark Length Max


No Dia D No 1 Load (KN)
R-12A 12 2000 5.0
R-16A 16 R.H. 2000 10.0
R-20A 20 Threaded 2000 15.0
R-24A 24 Rod 2000 23.0
R-30A 30 Dia = D 2000 35.0
R-36A 36 2000 53.0
R-42A 42 2000 73.0

Pipe Sup't Sling Rod Mark Length Mark Length Max


No Dia D No 1 No 2 Load (KN)
R-12B 12 1700 300 5.0
R-16B 16 R.H. 1700 L.H. 300 10.0
R-20B 20 Threaded 1700 Threaded 300 15.0
R-24B 24 Rod 1700 Rod 300 23.0
R-30B 30 Dia = D 1700 Dia = D 300 35.0
R-36B 36 1700 300 53.0
R-42B 42 1700 300 73.0

Pipe Sup't Sling Rod Mark No 1 Length


No Dia D
R-24C 24 R.H.Threaded Rod 3000
R-36C 36 Dia = D 3000

SUPPORT No RA, RB, RC


SUPPORT TYPE Sling Rod Sheet F30
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 2

A
H D

= =

B C

Pipe Sup't Dia D A B C E H Max


No Load (KN)
L-12 12 65 50 6 40 14 5.0
L-16 16 75 50 6 50 18 10.0
L-20 20 90 80 10 60 22 15.0
L-24 24 115 80 10 80 26 23.0
L-30 30 135 100 12 90 32 35.0
L-36 36 175 130 15 110 39 53.0
L-42 42 200 130 15 130 45 73.0

SUPPORT No L
SUPPORT TYPE Welding Lug Sheet F31
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 4

D
R = 25
A

L 6mm weephole
1 seal with mastic
after welding

Carbon Steel Pipes


Cradle for Pipe Supt No Mark No 1 (Note 1)
Standard shoes C1 10 thk Carbon
Long shoes C2 Steel plate
Anchors C3

Stainless Steel Pipes


Cradle for Pipe Supt No Mark No 1 (Note 1)
Standard shoes C101 10 thk Stainless
Long shoes C102 Steel plate
Anchors C103 ASTM-A-240 Type 316

Note 1 - For plate MTO see Table 2 Sheet F33

Table 1- Cradle dimensions

Pipe size C1 or C101 C2 or C102 C3 or C103


L A L A L A
2" - 10" 700
12" - 16" 132° 132° 800 132°
18" - 24" 600 900
26" - 40" 1000
42",46"-58",62"-66" 400 162° 162° 1100 162°
44" 166° 166° 1100 166°
60" 650 1150
68" 1100
70" 162° 162° 1150 162°
72" - 92" 600 1200

Assembly Tag No: - C1 or C2 or C3 or C101 or C102 or C103 - X


Detail No Pipe Size

Dimensions Required: - None


SUPPORT No C1, C2, C3, C101, C102, C103
SUPPORT TYPE Cradle Sheet F32
PIPE SIZE 2" - 92"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 4

Table 2- MTO for cradles C1, C2, C3, C101, C102, C103

Pipe Size D Area of plate required (cm²)


(") C1, C101 C2, C102 C3, C103
2 60 322 484 564
3 89 456 684 798
4 114 571 857 1000
6 168 820 1230 1435
8 219 1055 1582 1846
10 273 1304 1956 2282
12 324 1539 2308 3077
14 356 1684 2526 3368
16 406 1918 2877 3837
18 457 2152 3228 4843
20 508 2386 3579 5369
22 559 2620 3931 5896
24 610 2854 4282 6422
26 660 3088 4633 7721
28 711 3322 4984 8306
30 762 3556 5335 8891
32 813 3790 5686 9476
34 864 4025 6037 10061
36 914 4259 6388 10646
38 965 4493 6739 11231
40 1016 4727 7090 11816
42 1067 6088 9132 16742
44 1118 6375 10360 17532
46 1168 6662 9994 18322
48 1219 6950 10424 19112
50 1270 7237 10855 19901
52 1321 7524 11286 20691
54 1372 7811 11717 21481
56 1422 8099 12148 22271
58 1473 8386 12579 23061
60 1524 8673 14094 24935
64 1626 9247 13871 25430
66 1676 9535 14302 26220
68 1727 9822 15960 27010
70 1778 10109 16427 29063
72 1829 10396 15594 31189
76 1930 10971 16456 32912
80 2032 11545 17318 34635
84 2134 12119 18179 36358
88 2235 12694 19041 38082
92 2337 13268 19903 39805

SUPPORT No C1, C2, C3, C101, C102, C103


SUPPORT TYPE Cradle (Dimensions) Sheet F33
PIPE SIZE 2" - 92"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 2

Longitudinal
Weld

L
1
6mm weephole θ is the minimum angle
(per plate section) between longitudinal
seal with mastic welds at the bottom of
after welding the cradle

Carbon Steel Pipes


Cradle for Pipe Supt No Mark No 1 (Note 1)
Standard shoes C4 10 thk Carbon
Long shoes C5 Steel plate
Anchors C6

Stainless Steel Pipes


Cradle for Pipe Supt No Mark No 1 (Note 1)
Standard shoes C104 10 thk Stainless
Long shoes C105 Steel plate
Anchors C106 ASTM-A-240 Type 316

Note 1 - For plate MTO see Table 2 Sheet F35

Table 1- Cradle dimensions

Pipe size C4/C104 C5/C105 C6/C106 Angle θ


L L L (Min)
2" - 10" 700
12" - 16" 800
18" - 24" 400 600 900 150º
26" - 40" 1000
42" - 70" 1100
72" - 92" 1200

Assembly Tag No: - C4 or C5 or C6 or C104 or C105 or C106 - X


Detail No Pipe Size
Dimensions Required: - None
SUPPORT No C4, C5, C6, C104, C105, C106
SUPPORT TYPE Full encirclement cradle Sheet F34
PIPE SIZE 2" - 92"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 2

Table 2- MTO for cradles C4, C5, C6, C104, C105, C106

Pipe Size D Area of plate required (cm²)


(") C4, C104 C5, C105 C6, C106
2 60 879 1319 1539
3 89 1244 1866 2177
4 114 1558 2337 2726
6 168 2236 3355 3914
8 219 2877 4316 5035
10 273 3556 5333 7111
12 324 4196 6295 8393
14 356 4593 6890 9187
16 406 5232 7847 10463
18 457 5870 8805 13207
20 508 6508 9762 14643
22 559 7146 10720 16079
24 610 7785 11677 17515
26 660 8423 12634 21057
28 711 9061 13592 22653
30 762 9699 14549 24249
32 813 10338 15506 25844
34 864 10976 16464 27440
36 914 11614 17421 29035
38 965 12252 18379 30631
40 1016 12891 19336 32227
42 1067 13529 20293 37205
44 1118 14167 21251 38960
46 1168 14805 22208 40715
48 1219 15444 23166 42470
50 1270 16082 24123 44225
52 1321 16720 25080 45980
54 1372 17358 26038 47736
56 1422 17997 26995 49491
58 1473 18635 27952 51246
60 1524 19273 28910 53001
64 1626 20550 30825 56512
68 1727 21826 32739 60022
70 1778 22464 33697 61777
72 1829 23103 34654 69308
76 1930 24379 36569 73138
80 2032 25656 38484 76967
84 2134 26932 40398 80797
88 2235 28209 42313 84626
92 2337 29485 44228 88456

SUPPORT No C4, C5, C6, C104, C105, C106


SUPPORT TYPE Full encirclement cradle (Dimensions) Sheet F35
PIPE SIZE 2" - 92"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 3

10
Max
L
T

D
A

Pipe Pipe Mark No 1 Dimension


Sup't No Size A D L T
½ 37 60 60
¾ 43 65 60
1 Insulated U-Bolt 50 8 65 60
UA101 1½ Anchor for Stainless 75 80 70
2 Steel Pipes. 87 80 70
3 115 12 100 70
4 166 110 70

Assembly Tag No: - UA101 - X


Detail No Pipe Size
SUPPORT No UA101
SUPPORT TYPE Insulated U-Bolt Anchor for Stainless Steel pipes Sheet F36
PIPE SIZE ½" - 4"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 3

L
T

D
A

Pipe Pipe Mark No 1 Dimension


Sup't No Size A D L T
½ 37 60 60
¾ 43 65 60
1 Insulated U-Bolt 50 8 65 60
UG101 1½ Guide for Stainless 75 80 70
2 Steel Pipes. 87 80 70
3 115 12 100 70
4 166 110 70

Assembly Tag No: - UG101 - X


Detail No Pipe Size
SUPPORT No UG101
SUPPORT TYPE Insulated U-Bolt Guide for Stainless Steel pipes Sheet F37
PIPE SIZE ½" - 4"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 4

Plate Thickness = T

A Hole
Dia D

Dimensions and
Shape of Lug to be L
confirmed by vendor

Min Pipe
Dimensions (mm)
Pipe Wall Thk Maximum
Size (mm) Load (KN) L H Hole dia D A T
2 1.8 0.5 50 180 22 35 10
3 1.8 1.0 80 180 22 35 10
4 2.3 2.0 100 180 22 35 10
6 3.2 3.0 100 180 22 35 10
8 4.1 4.0 120 180 22 35 10
10 4.1 5.0 120 180 22 35 10
12 4.1 6.0 150 210 26 40 12
14 4.1 8.0 150 210 33 50 15
16 3.9 10.0 200 210 33 50 15
18 3.9 12.0 200 210 39 60 20
20 4.1 12.0 250 210 39 60 20
22 - 24 4.1 12.0 250 210 45 70 20
26 - 30 5.4 20.0 300 210 45 70 20
32 - 36 5.4 20.0 300 210 45 70 20
NOTES -
1- The lugs shall not be used as permanent pipe supports
2- These loads are based upon the tabulated wall thicknesses.
The following equation can be used to increase the actual allowable load: -
1 .5
tp
Allowable load = tabulated load * 1 .5
tt

Where: - t p is the pipe thickness (less c.a. and tolerances) of the pipe in question
t t is the tabulated pipe thickness

Assembly Tag No: - LL1 - X


Detail No Pipe Size

SUPPORT No LL1
SUPPORT TYPE Lifting Lugs for Piping Break-Out Spools from an elbow Sheet F38
PIPE SIZE 2" - 36"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 4
L T

A Hole
Dia D

B H

θ
R = 25

10 Thk Re-Pad 6mm weephole.


where required Seal with mastic
after welding
Min Pipe Re-pad
Dimensions (mm)
Pipe Wall Thk Maximum Required
Size (mm) Load (KN) (Y/N) L H Hole dia D A B T θ
2 1.8 0.5 N 100 120 22 35 10
3 1.8 1.0 N 100 120 22 35 10
4 2.3 2.0 N 100 120 22 35 10
6 3.2 3.0 N 100 150 22 35 10
8 4.1 4.0 N 120 150 22 35 10
10 4.1 5.0 N 120 150 22 35 10
12 4.1 6.0 N 120 150 26 40 12
14 4.1 8.0 Y 120 150 33 50 250 15 90
16 3.9 10.0 Y 120 180 33 50 250 15 90
18 3.9 12.0 Y 120 180 39 60 250 20 90
20 4.1 12.0 Y 120 180 39 60 250 20 90
22 - 24 4.1 15.0 Y 120 180 45 70 250 20 75
26 - 30 5.4 20.0 Y 150 180 45 70 300 20 60
32 - 36 5.4 25.0 Y 150 180 45 70 300 20 60
54 10 40.0 Y 200 210 63 100 400 20 45

NOTES -
1- The lugs shall not be used as permanent pipe supports
2- These loads are based upon the tabulated wall thicknesses.
The following equation can be used to increase the actual allowable load: -
1 .5
tp
Allowable load = tabulated load * 1 .5
tt

Where: - t p is the pipe thickness (less c.a. and tolerances) of the pipe in question
t t is the tabulated pipe thickness

Assembly Tag No: - LL2 - X


Detail No Pipe Size

SUPPORT No LL2
SUPPORT TYPE Lifting Lugs for Piping Break-Out Spools from pipe Sheet F39
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 1

o
45

1
1

50
(min)

45o

50 The gusset shall not be in the same plane as the pipe


min nipple and shall be typically welded to the bottom
A
or the side of the pipe

1
Angle between
gusset supports
and pipe axis One gusset
shall be shown
A for clarity View A-A
approx 45°
NOTE- A gusset support for orifice flanges is only required where a pipe nipple
has been introduced between the flange and the modular valve

For Stainless Steel Piping,


the Gusset shall be formed
by 2 flat plates welded 1
together (typ). See below: -

40

5
50 450
40
(min) (max)
NOTES
1- Gusset supports shall be installed in the shop where the branch and header are on the
same isometric, otherwise they shall be installed in the field.
2- The gusset length shall be cut and profiled as required to match the o.d. of pipe.
Support Mark No 1 Length Support Mark No 1 Size
GSW1 40 x 6 1000 5 Thk Stainless Steel Plate, 1000 x 40
Angle GSW101 Grade ASTM-A-240 (2 Off)
Assembly Tag No: - GSW1,GSW101 Type 316 or equivalent

Detail No
SUPPORT No GSW1,GSW101
SUPPORT TYPE Welded Gusset Support, Carbon & Stainless Steel pipes Sheet F40
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

Do not use on Nipo-flanges. 2


Use welded Gusset type GSW
1

Orientation of the angle Min


to be determined on site

Pipe Clip PC1 or


PC101 (Ref only)

45o

45o
Pipe Clip PC1 or
PC101 (Ref only)

Min

2
Orientation
of the angle
to be determined
on site

Pipe Clip PC1 or


PC101 (Ref only)

Min 450
(max)

NOTES Pipe Branch


1- All gusset supports shall be installed in the field Sup't No Pipe Size Mark No 1 Mark No 2
2- Field to cut length as required and ¾ UA-¾
profile gusset to match o.d. of pipe clamp GSB1 1 40 x 6 UA-1
1½ Angle UA-1½
Assembly Tag No: - GSB1,GSB101 - X ¾ UA101-¾
GSB101 1 Length UA101-1
Detail No Size Code 1½ = 1000 UA101-1½
SUPPORT No GSB1,GSB101
SUPPORT TYPE Bolted Gusset Support, Carbon & Stainless Steel pipes Sheet F41
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 0

D
R = 25
A

L 6mm weephole
1 seal with mastic
after welding

Carbon Steel Pipes


Cradle for Pipe Supt No Mark No 1 (Note 1)
Anchors on sleepers ≤ 600mm C7 10 thk Carbon
Anchors on sleepers > 600mm C8 Steel plate

Stainless Steel Pipes


Cradle for Pipe Supt No Mark No 1 (Note 1)
Anchors on sleepers ≤ 600mm C107 10 thk Stainless Steel Plate
Anchors on sleepers > 600mm C108 ASTM-A-240 Type 316

Area of plate
Pipe Size
D required (cm²)
(")
C7, C107 C8, C108
2 60 806 1129
3 89 1140 1596
4 114 1428 1999
Pipe size C7or C107 6 168 2255 3075
L A 8 219 2901 3956
2" - 4" 1000 10 273 3585 4889
6" - 16" 1100 132° 12 324 4231 5770
18" - 24" 1200 14 356 4632 6316
26" - 40" 1300 16 406 5275 7194
18 457 6457
20 508 7159
Pipe size C8 or C108 22 559 7861
L A 24 610 8563
2" - 4" 1400 132° 26 660 10037
6" - 16" 1500 28 711 10798
30 762 11558
32 813 12319
34 864 13080
36 914 13840
38 965 14601
40 1016 15361
Assembly Tag No: - C7 or C8 or C107 or C108 - X
Detail No Pipe Size

Dimensions Required: - None


SUPPORT No C7, C8, C107, C108
SUPPORT TYPE Cradle for Anchors on Concrete Sleepers Sheet F42
PIPE SIZE 2" - 40"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

Thickness E
T
D = =
X 2 lugs required for
rods 80mm and
larger
Radius
R

CL
Pipe
X C
Hole Dia A
H
View X-X
1

10mm
Continuous Thickness
Fillet Weld T

Notch around weld.


Radius = 25mm

CL
Pipe
View X-X

Pipe Size No of Lugs Thickness Radius Hole Dia Dimensions


T R H A C D E
48" 1 25 110 68 520 220 410 N/A
60" 1 25 95 50 463 178 300 N/A

Pipe Size Mark No 1 Dims


48" 25 Thk Plate 520 x 410
60" 25 Thk Plate 465 x 300

Assembly Tag No: - LL1 - X


Detail No Pipe Size

SUPPORT No LL1
SUPPORT TYPE Lifting Lugs for Piping Break-Out Spools from an elbow Sheet F43
PIPE SIZE 48" - 92"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0
L T
1
A Hole
Dia D

2 B H

θ
R = 25

6mm weephole.
10 Thk Re-Pad
Seal with mastic
where required
after welding
Min Pipe Re-pad
Dimensions (mm)
Pipe Wall Thk Maximum Required
Size (mm) Load (KN) (Y/N) L H Hole dia D A B T θ
2 1.8 0.5 N 100 120 22 35 10
3 1.8 1.0 N 100 120 22 35 10
4 2.3 2.0 N 100 120 22 35 10
6 3.2 3.0 N 100 150 22 35 10
8 4.1 4.0 N 120 150 22 35 10
10 4.1 5.0 N 120 150 22 35 10
12 4.1 6.0 Y 120 150 26 40 250 12 90
14 4.1 8.0 Y 120 150 33 50 250 15 90
16 3.9 10.0 Y 120 180 33 50 250 15 90
18 3.9 12.0 Y 120 180 39 60 250 20 90
20 4.1 12.0 Y 120 180 39 60 250 20 90
22 - 24 4.1 15.0 Y 120 180 45 70 250 20 75
26 - 30 5.4 20.0 Y 150 180 45 70 300 20 60
32 - 36 5.4 25.0 Y 150 180 45 70 300 20 60
Pipe Size Mark No 1 Dimension Mark No 2 Dimension
2-4 10 Thk Stainless Steel Plate 100 x 120
6 ASTM-A-240 Type 316 100 x 150
8 - 10 or equivalent 120 x 150
12 12 Thk Carbon Steel Plate 120 x 150 250 x 250
14 15 Thk Carbon Steel Plate 120 x 150 250 x 280
16 15 Thk Carbon Steel Plate 250 x 320
18 250 x 360
20 120 x 180 10 Thk Stainless 250 x 400
22 Steel Plate 250 x 370
24 ASTM-A-240 250 x 400
26 20 Thk Carbon Steel Plate Type 316 300 x 350
28 or equivalent 300 x 370
30 150 x 180 300 x 400
32 300 x 425
34 300 x 450
36 300 x 480
NOTES - 1- The lugs shall not be used as permanent pipe supports
2- These loads are based upon the tabulated wall thicknesses.
The following equation can be used to increase the actual allowable load: -
1 .5
tp
Allowable load = tabulated load * 1 .5
tt
Where: - t p is the pipe thickness (less c.a. and tolerances) of the pipe in question
t t is the tabulated pipe thickness
Assembly Tag No: - LL102 - X
Detail No Pipe Size
SUPPORT No LL102
SUPPORT TYPE Lifting Lugs for Piping Break-Out Spools from Stainless Steel pipe Sheet F44
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 0

X X
5 10
L
Max
T

3
D
10 Dia Hole in
C Existing Steel

Monel Backing
= Plate

40
=

View X-X
20
75

Pipe Dimension
Size C D L T
½ 31 44
¾ 37 47
1 44 8 50 43
1½ 58 57
2 70 63

Pipe Pipe Mark No 1 Developed Mark No 2 Mark No 3 Area


2
Size O.D. Length (4 Off) (cm )
½ 21 8 dia 137
¾ 27 Round 152 5 Thk
1 34 Monel 169 M 8 Nut Monel 30
1½ 48 Bar 205 plate
2 60 236
Assembly Tag No: - UG301 - X
Detail No Pipe Size
SUPPORT No UG301
SUPPORT TYPE U-Bolt Guide for pipes in the Caustic Sump Sheet F45
PIPE SIZE ½" - 2"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev 0

X X
5 10
L Max

3
10 Dia Hole in
D Existing Steel
C 2

Monel Backing
= Plate

40
=

View X-X
20
75

Pipe Dimension
Size C D L T
½ 29 49
¾ 35 52
1 42 8 55 35
1½ 56 62
2 68 68

Pipe Pipe Mark No 1 Developed Mark No 2 Mark No 3 Area


2
Size O.D. Length (4 Off) (cm )
½ 21 8 dia 144
¾ 27 Round 159 5 Thk
1 34 Monel 176 M 8 Nut Monel 30
1½ 48 Bar 212 plate
2 60 243
Assembly Tag No: - UA301 - X
Detail No Pipe Size
SUPPORT No UA301
SUPPORT TYPE U-Bolt Anchor for pipes in the Caustic Sump Sheet F46
PIPE SIZE ½" - 2"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

Pipe Support No SB301 - Guide Pipe Support No SB302 - Anchor

X X

1 1

3
3

500

X
X
Baseplate shall
30
rest on floor of
2
Caustic Sump
30

10mm Wide
Slotted
Hole
=

400 30

View X-X
=

NOTE-
Mark Nos 1 & 2 (base plate and angle)
shall be painted with an epoxy
= =
paint System AD
400

Pipe Pipe Mark No 1 Length Mark No 2 Area Mark No 3 Size


Sup't No Size (") (cm²)
SB301 ¾ 50 x 6 500 12 Thk 1600 Monel U-Bolt UG301-¾
Angle Plate Guide
SB302 ¾ 50 x 6 500 12 Thk 1600 Monel U-Bolt UA301-¾
Angle Plate Anchor

Assembly Tag No: - SB301 or SB302 - X


Detail No Pipe Size
SUPPORT No SB301, SB302
SUPPORT TYPE Base Guide/Anchor Pipes in Caustic Sump Sheet F47
PIPE SIZE ¾"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0
X

500

Baseplate shall
X rest on floor of
Caustic Sump
2
30

30

10mm
Field Weld Wide
Slotted
Hole

400 30

View X-X
=
NOTE-
Mark Nos 1 & 2 (base plate
and angle)
= 113 = shall be painted with an
epoxy
500
paint System AD

Pipe Pipe Mark No 1 Length Mark No 2 Area Mark No 3 Size


Sup't No Size (") (cm²) (2 Off)
SB303 ¾ 50 x 6 1000 12 Thk 2000 Monel U-Bolt UG301-¾
Angle Plate Guide

Assembly Tag No: - SB303 - X


Detail No Pipe Size
SUPPORT No SB303
SUPPORT TYPE Base Guide for 2 pipes in Caustic Sump Sheet F48
PIPE SIZE ¾"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

50
min
A

Angle between
gusset supports
Bolt Angle into one of the and pipe axis
four existing holes in the shall be
flange body. A washer is 2 approx 45°
required either side of 3 1
the angle
A

SP-1914
or SP-1916

View A-A

One gusset
shown
Field Welds for clarity

NOTES
1- The gusset length shall be cut and profiled as required to match the o.d. of pipe.

Support Mark No 1 Length Mark No 2 Length Mark No 3 No Off


GSW2 40 x 6 1000 M10 Bolt 30 M10 2
Angle Washers

Assembly Tag No: - GSW2


Detail No
SUPPORT No GSW2
SUPPORT TYPE Gusset Support for SP Item Nos. SP-1914 & SP-1916 Sheet F49
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3
4-M20 threaded rod with Hilti HY150
Pipe Support Section resin capsule adhesive.
HEA 100 field welded (Hilti HIT-ICE resin to be used if the
2
to 20 thk. Plate. installation temperature is below -5°C)
Max length = 620, Dimension to be
Plinth cast on confirmed at site. Varies due to paving

(Type G1)
paving by piping

30 Grout
sloping. NOTE 1
contractor.
3 M20 Nuts
150
5 U/S of Plate EL. 100,200 50

100

200
2 layers of A393 140 Slab.
Structural mesh C25
Paving
PVC Sheet

Controlled frost free graded granular fill 6 NOTE 1


(type 1) compacted in 200mm layers to 7
spec. (90% max.dry density) ELEVATION

60
(Typ)
(Typ)

100 100 1 20 Thick Plate


60

100
A
B

4 2 - 8 dia. stirrups
100

24 Dia holes in each


corner of the plate
A (4 off)
PLAN
B

NOTES 1- Refer to Section 10 of this Spec for a procedure for the installation of bolts,
grouting and monitoring the settlement of the paving
2- For General Notes refer to Drawing Nos. 60-0000-Q-STD-0010-01 and 02

Dimensions (mm) Allowable Loads


Support A B Vertical (KN) Bending Moment (KNm)
F8N-1 320 400 20.0 4.0
Mark No 1 Area Mark No 2 Total Mark No 3 Mark No 4 Total Mark No 5
(cm2) Length (8 Off) Length (8 Off)
20 Thk 1025 20 Dia Bar 2500 M20 Nut 8 Dia Bar 2000 M20 Washers
Plate Threaded
Mark No 6 Mark No 7
Cementitious Grout Structural Concrete
Assembly Tag No: - F8N-1
(G1) 0.01m3 Grade (K25AE) 0.05m3
SUPPORT No F8N-1
SUPPORT TYPE Pipe Support foundation for New Paving Sheet G1
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3
Pipe Support Section 4-M20 threaded rod with Hilti HY150
HEA 160 or HEA 200 field resin capsule adhesive.
2
welded to 20 thk. Plate. (Hilti HIT-ICE resin to be used if the
installation temperature is below -5°C)
Plinth cast on (Max length = 620, Dimension to be

(Type G1)
paving by piping confirmed at site. Varies due to paving

30 Grout
contractor. sloping).NOTE 1
3 M20 Nuts
150
6 30 U/S of Plate EL. 100,200 50

100

200
2 layers of A393 140 Slab.
Structural mesh C25
Paving

PVC Sheet
8 7 NOTE 1
Controlled frost free graded 4
granular fill (type 1) compacted in 4-16 dia. threaded rod x 140 projection with
200mm layers to spec. (90% ELEVATION Hilti HY150 capsule adhesive. (Max length =
max.dry density) 400, Dimension to be confirmed at site. Varies
60 due to paving sloping).
(Typ)
1 20 Thick Plate
(Typ)

= =
60

5 2 - 8 dia. stirrups

24 Dia holes in each


=
A

corner of the plate


B

(4 off)

A
PLAN
B

NOTES 1- Refer to Section 10 of this Spec for a procedure for the installation of bolts,
grouting and monitoring the settlement of the paving
2- For General Notes refer to Drawing Nos. 60-0000-Q-STD-0010-01 and 02
Dimensions (mm) Allowable Loads
Support A B Vertical (KN) Bending Moment (KNm)
F8N-2 500 600 25.0 8.0
Mark No 1 Area Mark No 2 Total Mark No 3 Mark No 4 Total Mark No 5 Total
(cm2) Length (8 Off) Length Length
20 Thk 2500 20 Dia Bar 2500 M20 Nut 16 Dia Bar 1600 8 Dia Bar 6000
Plate Threaded Threaded
Mark No 6 Mark No 7 Mark No 8
M20 Cementitious Grout Structural Concrete
Washers (G1) 0.01m3 Grade (K25AE)
Assembly Tag No: - F8N-2
(8 Off) 0.12m3
SUPPORT No F8N-2
SUPPORT TYPE Pipe Support foundation for New Paving Sheet G2
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

30
Maximum Applied Vertical Load 'P' (KN)

25

20

10

0
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Maximum Applied Moment 'M' (KNm)


F8N-1 (200 thk. paving x 400 sq. pier)

F8N-2 (200 thk. paving x 600 sq. pier)

'P'

'M'
F8N-1 x 200 thk.
F8N-2 x 200 thk.
F8N-1 x 400 sq.
F8N-2 x 600 sq.

Effective paving length = 2.0m


2
Effective paving area = 4.0m
CRITERIA ASSUMED
2
1- The allowable vertical loads are based upon an effective paving area of 4.0m , which equates to a
distance between the piers of 2.0m. If the distance between the piers is less than 2.0m the allowable
loads shall be reduced in proportion to the effective pier area.
Example- Distance between piers = 1.5m
2 2
Allowable load shall be 1.5 /2.0 = 0.56 x load in graph
2
2- Allowable ground bearing pressure of 50KN/m
3- The face of the pier shall be 1.0m minimum away from the edge of the slab.
4- The concrete grade shall be at least 25N/mm2
5- There are 2 layers of mesh fabric grade A393 in the paving
6- All slab joints are dowelled
SUPPORT No F8N-1, F8N-2
SUPPORT TYPE Pipe Support Foundation Loading Graph for F8N-1, F8N-2 Sheet G3
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3
100 400
(typ) 140 140
SUPPORT SHALL
BE USED FOR
THE SGI
PROJECT ONLY

140 1
400
140 24dia holes
(4 off)

Pipe Support PLAN


Section Size
Trim post and site
HEA 100 or smaller
weld to plate
2
3
U/S EL 100,200 30

25 75 100
4
Grade EL 100,000 300 bar
50 embed-
75
cover ment
50
5
75
Concrete cover
Infill 6 dia helix
@ 200 pitch 3000
6
(Note 1)
7 A A

ELEVATION
450 dia Augered Pile
25 Grade Concrete
75
NOTES: cover
1- When the auger is located on a
piling mat or pile cap it shall not
penetrate the surface of them.
The approximate depth of the auger
will be 2000mm where there is a
piling mat and 1200mm where 450 Dia
there is a pile cap.

75
Assembly Tag No: - F9-1 cover SECTION A-A
SUPPORT No F9-1
Augered Pile, Pipe Support Foundation for welded
SUPPORT TYPE Sheet G4
posts in non-paved areas (HEA 100)
PIPE SIZE All
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3

SUPPORT SHALL
BE USED FOR
THE SGI
PROJECT ONLY

Allowable loads Minimum allowable


Bending distance between augers
Vertical Moment Auger diameters Distance
(KN) (KNm) (mm) (mm)
25.0 4.0 450 - 450 1500

Mark No 1 Area Mark No 2 Length Mark No 3 Mark No 4 Mark No 5 Total


(cm2) (4 Off) (4 Off) (12 Off) Length
20 Thk 20 dia 20 dia 20 dia 12 dia
Plate 1600 threaded 400 Washers Nuts rebar 10500
rod

Mark No 6 Length Total Mark No 7 Total


(Note 1) (6 Off) Length (Note 1) Length
20 dia 3200 19200 6 dia 15000
rebar helix

NOTES:
1- MTO is based upon a auger length of 3000mm

Assembly Tag No: - F9-1


SUPPORT No F9-1
Augered Pile, Pipe Support Foundation for welded
SUPPORT TYPE Sheet G5
posts in non-paved areas (HEA 100)(dim'ns)
PIPE SIZE All
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3
100 500
(typ) 190 190 SUPPORT SHALL
BE USED FOR
THE SGI
PROJECT ONLY

190 1
500
190 24dia holes
(4 off)

Pipe Support PLAN


Section Size
Trim post and site
HEA 160 or HEA 200
weld to plate
2
3
U/S EL 100,200 30

25 75 100
4
Grade EL 100,000 300 bar
embed-
75
cover ment
50
5
75
Concrete cover
Infill
6 dia helix
6 @ 200 pitch 3000
(Note 1)
7 A A

ELEVATION
450 dia Augered Pile
25 Grade Concrete

75
cover
NOTES:
1- When the auger is located on a
piling mat or pile cap it shall not
penetrate the surface of them.
The approximate depth of the auger
will be 2000mm where there is a 450 Dia
piling mat and 1200mm where
there is a pile cap.

75
Assembly Tag No: - F9-2 cover SECTION A-A
SUPPORT No F9-2
Augered Pile, Pipe Support Foundation for welded
SUPPORT TYPE Sheet G6
posts in non-paved areas (HEA160 or HEA200)
PIPE SIZE All
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3

SUPPORT SHALL
BE USED FOR
THE SGI
PROJECT ONLY

Allowable loads Minimum allowable


Bending distance between augers
Vertical Moment Auger diameters Distance
(KN) (KNm) (mm) (mm)
25.0 4.0 450 - 450 1500

Mark No 1 Area Mark No 2 Length Mark No 3 Mark No 4 Mark No 5 Total


(cm2) (4 Off) (4 Off) (12 Off) Length
20 Thk 20 dia 20 dia 20 dia 12 dia
Plate 2500 threaded 400 Washers Nuts rebar 12500
rod

Mark No 6 Length Total Mark No 7 Total


(Note 1) (6 Off) Length (Note 1) Length
20 dia 3200 19200 6 dia 15000
rebar helix

NOTES:
1- MTO is based upon a auger length of 3000mm

Assembly Tag No: - F9-2


SUPPORT No F9-2
Augered Pile, Pipe Support Foundation for welded
SUPPORT TYPE Sheet G7
posts in non-paved areas (HEA160 or HEA200)(dim'ns)
PIPE SIZE All
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3
100 500
(typ) 190 190 SUPPORT SHALL
BE USED FOR
THE SGI
PROJECT ONLY

190 1
500
24dia holes
190 (4 off)

PLAN

Existing BS2 or BS4

U/S EL 100,200
25 75 100
2
Grade EL 100,000 300 bar
embed-
75
cover ment
3
50
4
75
Concrete cover
Infill
6 dia helix 3000
5 @ 200 pitch (Note 1)

6 A A

ELEVATION
450 dia Augered Pile
25 Grade Concrete
75
cover
NOTES:
1- When the auger is located on a
piling mat or pile cap it shall not
penetrate the surface of them.
The approximate depth of the auger
will be 2000mm where there is a 450 Dia
piling mat and 1200mm where
there is a pile cap.

75
Assembly Tag No: - F9-4 cover SECTION A-A
SUPPORT No F9-4
Augered Pile, Pipe Support Foundation for base
SUPPORT TYPE Sheet G8
supports in non-paved areas (Trunnion ≤ 6")
PIPE SIZE All
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3

SUPPORT SHALL
BE USED FOR
THE SGI
PROJECT ONLY

Minimum allowable
Allowable loads distance between augers
Vertical Shear Auger diameters Distance
(KN) (KN) (mm) (mm)
25.0 5.0 450 - 450 1500

Mark No 1 Area Mark No 2 Length Mark No 3 Total


(cm2) (4 Off) Length
20 Thk 20 dia 12 dia
Plate 2500 threaded 350 rebar 12500
rod

Mark No 4 Mark No 5 Length Total Mark No 6 Total


(4 Off) (Note 1) (6 Off) Length (Note 1) Length
20 dia 20 dia 3200 19200 6 dia 15000
Nuts rebar helix

NOTES:
1- MTO is based upon a auger length of 3000mm

Assembly Tag No: - F9-4


SUPPORT No F9-4
Augered Pile, Pipe Support Foundation for base
SUPPORT TYPE Sheet G9
supports in non-paved areas (Trunnion ≤ 6")(dim'ns)
PIPE SIZE All
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
100 700
(typ) 140 140 GENERAL
REVISION
1

140
700
140

PLAN

Existing BS2 or BS4

U/S EL 100,200
25 75 100
2
Grade EL 100,000 300 bar
embed-
75
3 cover ment
50
4
75
Concrete cover
Infill 3000
6 dia helix
@ 200 pitch (Note 1)
5
6 A A

450 dia Augered Pile ELEVATION


25 Grade Concrete
75
cover

NOTES:
1- When the auger is located on a
piling mat or pile cap it shall not
penetrate the surface of them.
The approximate depth of the auger 450 Dia
will be 2000mm where there is a
piling mat and 1200mm where
there is a pile cap.

75
Assembly Tag No: - F9-5 cover SECTION A-A
SUPPORT No F9-5
Augered Pile, Pipe Support Foundation for base
SUPPORT TYPE Sheet G10
supports in non-paved areas (Trunnion ≥8")
PIPE SIZE All
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

GENERAL
REVISION

Minimum allowable
Allowable loads distance between augers
Vertical Shear Auger diameters Distance
(KN) (KN) (mm) (mm)
25.0 5.0 450 - 450 1500

Mark No 1 Area Mark No 2 Length Mark No 3 Total


(cm2) (4 Off) Length
20 Thk 20 dia 12 dia
Plate 4900 threaded 350 rebar 16000
rod

Mark No 4 Mark No 5 Length Total Mark No 6 Total


(4 Off) (Note 1) (6 Off) Length (Note 1) Length
20 dia 20 dia 3200 19200 6 dia 15000
Nuts rebar helix

NOTES:
1- MTO is based upon a auger length of 3000mm

Assembly Tag No: - F9-5


SUPPORT No F9-5
Augered Pile, Pipe Support Foundation for base
SUPPORT TYPE Sheet G11
supports in non-paved areas (Trunnion ≥8")
PIPE SIZE All
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 4
4 threaded rods with Hilti HY150 resin
Existing Trunnion Support 2 capsule adhesive.
No BS5 or BS2 (Hilti HIT-ICE resin to be used if the
installation temperature is below -5°C)

Grout (Note 1)

Levelling nut
Existing piled NOTE 1
3 Nuts (8 Off)

(Type G1)
foundation
by civil 4 Washers (8 Off)
contractor or
pipe support U/S of Plate EL. 100,200
foundation.
5
Paving or Grade

Use 24dia drill bit


for 20dia bolts. L
Use 35dia drill bit
C
for 30dia bolts. ELEVATION
Note 1- Grout thickness = 25mm for baseplates smaller than 500 x 500.
Grout thickness = 40mm for baseplates 500 x 500 and larger.
60
(Typ)

(Typ)
60

20 dia grout holes (2 off)


NOTE - Only required for
base plates 800 x 800
or larger
B

125
Bolt Holes in each
corner of the plate
dia = D (4 off)

A
PLAN
B

NOTE 1- Refer to Section 10 of this Spec for a procedure for the installation of bolts,
grouting and monitoring the settlement of the paving
2- For General Notes refer to Drawing Nos. 60-0000-Q-STD-0010-01 and 02
Trunnion Dimensions (mm) Max Axial Foundation reference
Size A B C L dia D Load (KN) (if required)
2, 3 420 600 310 25.0 F9-6
4, 6 550 750 175 325 24 F9-7
8, 10, 12 700 900 50.0 F9-8
16, 18, 20 850 1050 280 460 34 100.0 Foundation to be
24 950 1150 designed by Civils
Trunnion Mark No 1 Area Mark No 2 Length Mark No 3 Mark No 4 Mark No 5
Size (cm2)
2, 3 20 Thk 1764 20 Dia Bar 310(4 Off) M20 Nut (8Off) M20 Cementitious Grout
4, 6 Plate 3025 Threaded 325(4 Off) (8 Off) Washers (G1) 0.02m3
8, 10, 12 4900
16, 18, 20 25 Thk 7225 30 Dia Bar 460(4 Off) M30 Nut (8Off) M30 Cementitious Grout
24 Plate 9025 Threaded (8 Off) Washers (G1) 0.03m3
Assembly Tag No: -F8N3 - X
Detail No Trunnion Size
SUPPORT No F8N3
Pipe Support baseplate on a civil foundation or
SUPPORT TYPE Sheet G12
pipe support foundation No F9-6, F9-7 or F9-8
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3
Existing Post 4 threaded rods with Hilti HY150 resin
2
capsule adhesive.
(Hilti HIT-ICE resin to be used if the

25 Thk Grout
installation temperature is below -5°C)

Levelling nut
(Type G1)
Existing piled 3 Nuts (8 Off) NOTE 1
foundation
by civil 4 Washers (4 Off)
contractor. U/S of Plate EL. 200
above Local Grade

5 NOTE 1
Local Grade

Use 24dia drill bit


for 20dia bolts.
ELEVATION
L
60
C
(Typ)

(Typ)
60

1
B

Bolt Holes in each


corner of the plate
dia = D (4 off)
A
PLAN
B

NOTE 1- Refer to Section 10 of this Spec for a procedure for the installation of bolts,
grouting and monitoring the settlement of the paving
2- For General Notes refer to Drawing Nos. 60-0000-Q-STD-0010-01 and 02
Size Pipe support Dimensions (mm)
Code Section A B C L dia D
A 70 Angle 250 450 175 300 24
B HEA 100 320 500 175 300 24
C HEA 160 or HEA 200 400 600 175 300 34
Allowable Loads
Size Pipe support Vertical Bending Shear Foundation reference
Code Section (KN) Moment (KNm) (KN) (if required)
A 70 Angle 5.0 Negligible Negligible F9-10
B 70 Angle or HEA 100 25.0 4.0 2.0 F9-6
C HEA 160 or HEA 200 50.0 8.0 4.0 F9-9
Size Mark No 1 Area Mark No 2 Length Mark No 3 Mark No 4 Mark No 5
Code (cm2) (4 Off)
A 20 Thk 625 20 Dia Bar 300(4 Off) M20 Nut M20 Cementitious Grout
B Plate 1024 Threaded 300(4 Off) (8 Off) Washers (G1) 0.01m3
C 1600 300(4 Off)
Assembly Tag No: -F8N4 - X
Detail No Size Code
SUPPORT No F8N4
Pipe Support baseplate on a civil foundation or
SUPPORT TYPE Sheet G13
pipe support foundation No F9-6, F9-9 or F9-10
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
Ref Trunnion 2" or 3"
or Post size HEA100

40 Ref F8-N3 or
Grout F8-N4 Size Code B

160 EL Local Grade

450
X X
Bitumen
900 Coating
4 100 (Typical)
2
1
3

300

300 5

K25AE Mass
200 1400 Square 200 1000g 0.25mm
Concrete
Thk Polythene
4 Sheeting

Pipe 600
CL 3
Support Square

75 Section X-X
Cover
(Typ)
CL Pipe Support

Pipe Support on Allowable Loads


Foundation F9-6 Axial (KN) Shear (KN) Bending Moment (KNm)
Welded Post HEA100 25.0 2.0 4.0
Trunnion 2" or 3" 25.0 7.5 -
Mark No Material No of Bars Length of Shape Dimensions
Each Bar Code A B
1 16 dia Rebar Type AIII 12 (6 E-W) 1225 20 1225
2 16 dia Rebar Type AIII 8 1600 37 1185
3 10 dia Rebar Type AIII 6 1900 61 440 440
4 (Note 2) 12 dia Rebar Type AIII 4 1250 39 600 100
Material Take Off - Reinforcement Only
Bar Type - Size AIII - 16 AIII - 12 AIII - 10
Total Length (m) 28 5 12
Weight (kg) 45 5 8
Mark No Material Quantity Matman Code
Structural Concrete Grade (K25AE) 2.0 m3 1011651
5 Polythene Sheeting 4.4 m2 1060510
Found'n Bitumen Emulsion 9 Litres 1070510
Assembly Tag No: -F9-6 NOTES: 1- For General Notes refer to Drawing Nos. 60-
0000-Q-STD-0010-01 and 02
Detail No 2- Optional lifting lugs for Precast Base
SUPPORT No F9-6
Pipe Support foundation for non paved areas for
SUPPORT TYPE Sheet G14
2" & 3" trunnions and welded posts HEA 100
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Ref Trunnion 4" or 6"

40 Ref F8-N3
Grout

160 EL Local Grade

450
X X
Bitumen
900 Coating
4 100 (Typical)
2
1
3

300

300
5

K25AE Mass 200 1400 Square 200


Concrete
1000g 0.25mm
4 Thk Polythene
Sheeting
2

Pipe 750
CL 3
Support Square

75 Section X-X
Cover
(Typ)
CL Pipe Support

Pipe Support on Allowable Loads


Foundation F9-7 Axial (KN) Shear (KN) Bending Moment (KNm)
Trunnion 4" or 6" 25.0 7.5 -
Mark No Material No of Bars Length of Shape Dimensions
Each Bar Code A B
1 16 dia Rebar Type AIII 16 (8 E-W) 1225 20 1225
2 16 dia Rebar Type AIII 12 1600 37 1185
3 10 dia Rebar Type AIII 6 2500 61 590 590
4 16 dia Rebar Type AIII 4 1575 39 750 130
Material Take Off - Reinforcement Only
Bar Type - Size AIII - 16 AIII - 10
Total Length (m) 46 15
Weight (kg) 73 10
Mark No Material Quantity Matman Code
2.8 m3
Structural Concrete Grade (K25AE) 1011651
5 Polythene Sheeting 5.3 m2 1060510
Found'n Bitumen Emulsion 11 Litres 1070510
Assembly Tag No: -F9-7 NOTES: 1- For General Notes refer to Drawing Nos. 60-
0000-Q-STD-0010-01 and 02
Detail No 2- Optional lifting lugs for Precast Base
SUPPORT No F9-7
Pipe Support foundation for non paved areas for
SUPPORT TYPE Sheet G15
4" & 6" trunnions
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Ref Trunnion 8",10" or 12"

40 Ref F8-N3
Grout

160 EL Local Grade

450
X X
Bitumen
900
4 Coating
100
(Typical)
2
1
3

300

300
5

K25AE Mass
200 1600 Square 200
Concrete 1000g 0.25mm
Thk Polythene
4 Sheeting
2

Pipe 900
CL 3
Support Square

75 Section X-X
Cover
(Typ)
CL Pipe Support

Pipe Support on Allowable Loads


Foundation F9-8 Axial (KN) Shear (KN) Bending Moment (KNm)
Trunnion 8",10" or 12" 50.0 15.0 -
Mark No Material No of Bars Length of Shape Dimensions
Each Bar Code A B
1 16 dia Rebar Type AIII 16 (8 E-W) 1425 20 1425
2 16 dia Rebar Type AIII 12 1600 37 1185
3 10 dia Rebar Type AIII 6 3100 61 740 740
4 16 dia Rebar Type AIII 4 1575 39 750 130
Material Take Off - Reinforcement Only
Bar Type - Size AIII - 16 AIII - 10
Total Length (m) 49 19
Weight (kg) 75 12
Mark No Material Quantity Matman Code
Structural Concrete Grade (K25AE) 2.8 m3 1011651
5 Polythene Sheeting 5.3 m2 1060510
Found'n Bitumen Emulsion 16 Litres 1070510
Assembly Tag No: -F9-8 NOTES: 1- For General Notes refer to Drawing Nos. 60-
0000-Q-STD-0010-01 and 02
Detail No
2- Optional lifting lugs for Precast Base
SUPPORT No F9-8
Pipe Support foundation for non paved areas for
SUPPORT TYPE Sheet G16
8",10" & 12" trunnions
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
Ref Post size HEA160 or HEA200

40
Ref F8-N4 Size Code C
Grout

160 EL Local Grade

450
X X
Bitumen
900 Coating
4 (Typical)
100
2
1
3

300

5
300

K25AE Mass
Concrete 200 1600 Square 200
1000g 0.25mm
Thk Polythene
4 Sheeting
2

Pipe 600
CL 3
Support Square

75 Section X-X
Cover
(Typ)
CL Pipe Support

Pipe Support on Allowable Loads


Foundation F9-9 Axial (KN) Shear (KN) Bending Moment (KNm)
Welded Post HEA160
50.0 4.0 8.0
or HEA 200
Mark No Material No of Bars Length of Shape Dimensions
Each Bar Code A B
1 16 dia Rebar Type AIII 16 (8 E-W) 1425 20 1425
2 16 dia Rebar Type AIII 8 1600 37 1185
3 10 dia Rebar Type AIII 6 1900 61 440 440
4 12 dia Rebar Type AIII 4 1250 39 600 100
Material Take Off - Reinforcement Only
Bar Type - Size AIII - 16 AIII - 12 AIII - 10
Total Length (m) 36 5 12
Weight (kg) 57 5 8
Mark No Material Quantity Matman Code
Structural Concrete Grade (K25AE) 2.5 m3 1011651
5 Polythene Sheeting 5.3 m2 1060510
(Found'n) Bitumen Emulsion 11 Litres 1070510
Assembly Tag No: -F9-9 NOTES: 1- For General Notes refer to Drawing Nos. 60-
0000-Q-STD-0010-01 and 02
Detail No
2- Optional lifting lugs for Precast Base
SUPPORT No F9-9
Pipe Support foundation for non paved areas for
SUPPORT TYPE Sheet G17
welded posts HEA 160 & HEA 200
PIPE SIZE All Sizes
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
Ref Small Bore Pipe Support
or Post size 70 x 8 Angle

40 Ref F8-N4 Size Code A


Grout

160 EL Local Grade

450
X X
1200
3
100
1
Bitumen
2 Coating
(Typical)

300 4

K25AE Mass 800 Square


Concrete
1000g 0.25mm
2 Thk Polythene
Sheeting

3
Pipe 450
CL 1
Support Square

75 Section X-X
Cover
(Typ)
CL Pipe Support

Pipe Support on Allowable Loads


Foundation F9-10 Axial (KN) Shear (KN) Bending Moment (KNm)
Post 70 x 8 Angle 5.0 - -
Mark No Material No of Bars Length of Shape Dimensions
Each Bar Code A B
1 16 dia Rebar Type AIII 8 1175 20 1175
2 10 dia Rebar Type AIII 7 1300 61 290 290
3 12 dia Rebar Type AIII 4 1250 39 600 100
Material Take Off - Reinforcement Only
Bar Type - Size AIII - 16 AIII - 12 AIII - 10
Total Length (m) 10 5 10
Weight (kg) 16 5 7
Mark No Material Quantity Matman Code
Structural Concrete Grade (K25AE) 0.5 m3 1011651
4 Polythene Sheeting 1.2 m2 1060510
Found'n Bitumen Emulsion 7.7 Litres 1070510
Assembly Tag No: -F9-10 NOTES: 1- For General Notes refer to Drawing Nos. 60-
0000-Q-STD-0010-01 and 02
Detail No
2- Optional lifting lugs for Precast Base
SUPPORT No F9-10
Pipe Support foundation for non paved areas for
SUPPORT TYPE Sheet G18
Small Bore Pipe Supports and 70 x 8 Angle Posts
PIPE SIZE ½" - 2"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

B.O.P.

B.O.P.

Note 2
See
Note 2
See

Pipe Size Pipe Size


3/4" - 3" 4" - 24"

Pipe Size
3/4" - 24"
300
= =

Support Insulation Thickness


Type (mm)
CS1-A 30
CS1-B 40
CS1-C 50
CS1-D 60
CS1-E 70
CS1-F 80
CS1-G 90
CS1-H 100
CS1-J 110

NOTE
1, For details of Cold Shoes see Specification No. 60-0000-L-SPE-1003.
2, For shoe height see Document No. 60-0000-L-SPE-0002.

Assembly Tag No: - CS1 - X - X

Detail No Pipe Size


SUPPORT No CS1
SUPPORT TYPE Cold Shoe, Standard Length Sheet H1
PIPE SIZE 3/4" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

B.O.P.

B.O.P.

Note 2
See
Note 2
See

Pipe Size Pipe Size


3/4" - 3" 4" - 24"

Pipe Size
3/4" - 24"
500
= =

Support Insulation Thickness


Type (mm)
CS2-A 30
CS2-B 40
CS2-C 50
CS2-D 60
CS2-E 70
CS2-F 80
CS2-G 90
CS2-H 100
CS2-J 110

NOTE
1, For details of Cold Shoes see Specification No. 60-0000-L-SPE-1003.
2, For shoe height see Document No. 60-0000-L-SPE-0002.

Assembly Tag No: - CS2 - X - X

Detail No Pipe Size


SUPPORT No CS2
SUPPORT TYPE Cold Shoe, Long Sheet H2
PIPE SIZE 3/4" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

B.O.P.
Note 2
(Typ.)
See

Pipe Size
8" - 24"

Support Insulation Thickness


Type (mm)
CS3-A 30
CS3-B 40
CS3-C 50
CS3-D 60
300
CS3-E 70 =
=
CS3-F 80
CS3-G 90 Pipe Size
CS3-H 100 8" - 24"
CS3-J 110

NOTE
1, For details of Cold Shoes see Specification No. 60-0000-L-SPE-1003.
2, For shoe height see Document No. 60-0000-L-SPE-0002.

Assembly Tag No: - CS3 - X - X

Detail No Pipe Size


SUPPORT No CS3
SUPPORT TYPE Cold Double Shoe, Standard Length Sheet H3
PIPE SIZE 8" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

B.O.P.

B.O.P.

Note 2
See
Note 2
See

Pipe Size Pipe Size


3/4" - 3" 4" - 24"

Pipe Size
3/4" - 24"
L
= =

Support Insulation Thickness Pipe Dimension


Type (mm) Size L
CAS1-A 30 3/4" - 10" 600
CAS1-B 40 12" - 24" 800
CAS1-C 50
CAS1-D 60
CAS1-E 70
CAS1-F 80
CAS1-G 90
CAS1-H 100
CAS1-J 110

NOTE
1, For details of Cold Anchor Shoes see Specification No. 60-0000-L-SPE-1003.
2, For shoe height see Document No. 60-0000-L-SPE-0002.

Assembly Tag No: - CAS1 - X - X

Detail No Pipe Size


SUPPORT No CAS1
SUPPORT TYPE Anchor Shoe - Cold Insulated Lines Sheet H4
PIPE SIZE 3/4" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

See See
Note 1 Note 1

Pipe Size Pipe Size


3/4" - 3" 4" - 24"
Do not weld
along Do not weld
this face along
this face
100

150
100 1
2 Gap 2 Gap
(typ) (typ) 2

= = = =

Pipe Mark Area Mark Total Maximum Anchor


Size No. 1 (cm²) No. 2 Length Load (KN)
3/4" - 3" 10 Thk.Plt. 200 HOLD
4" - 10" HEA100 300 HOLD
12" - 16" HEA160 300 HOLD
18" - 24" HEA200 300 HOLD

Note
1. For details of Cold Anchor Shoe see CAS1.

Assembly Tag No: - CDA1 - X

Detail No. Pipe Size

SUPPORT No CDA1
SUPPORT TYPE Anchor Shoe - Cold Insulated Lines Sheet H5
PIPE SIZE 3/4" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

4
H

See
Note 1 Pipe Size
3/4" - 24"

Support Insulation Thickness Pipe Dimension 'H' Maximum


Type (mm) Size Maximum Minimum Load (KN)
CH1-A 30 3/4" - 1" 500 2.0
CH1-B 40 1½ - 2" 500 3.0
2000
CH1-C 50 3" - 6" 600 5.0
CH1-D 60 8" 700 8.0
CH1-E 70 10" - 14" 800 12.3
2200
CH1-F 80 16" - 18" 900 20.0
CH1-G 90 20" - 24" 2400 1100 27.0
CH1-H 100
CH1-J 110

Note
1. For details of Hanger Clamp see Specification No. 60-0000-L-SPE-1003.

Assembly Tag No: - CH1 - X - X


Detail No Pipe Size
SUPPORT No CH1
SUPPORT TYPE Non-Adjustable Hanger for Cold Insulated Pipe Sheet H6
PIPE SIZE 3/4" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Pipe Mark No.1 Size Mark No.2 Size Mark No.3 Size
Size (1 Off) (1 Off) (2 Off)
3/4" - 2" L-12 CL-12 M12
3" - 6" L-16 CL-16 M16
8" Welding L-20 Clevis CL-20 Nut M20
10" - 14" Lug L-24 CL-24 M24
16" - 18" L-30 CL-30 M30
20" - 24" L-36 CL-36 M36

Pipe Mark No.4 Size Mark No.5 Size


Size (1 Off) (1 Off)
3/4" - 2" R-12A WENR-12
3" - 6" R-16A WENR-16
8" Threaded R-20A Weldless WENR-20
10" - 14" Sling Rod R-24A Eye Nut WENR-24
16" - 18" R-30A WENR-30
20" - 24" R-36A WENR-36

SUPPORT No CH1
SUPPORT TYPE Non-Adjustable Hanger for Cold Insulated Pipe Sheet H7
PIPE SIZE 3/4" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

See Note 1
5T

Cold Insulate Trunnion to


depth shown
100

A
Hole in centre of plate =
1 Trunnion dia. + 2mm

For Trunnion details BS1 or BS2 (Ref.)


refer to Isometric

Existing Steel or Base


Plate
NOTE
1. 'T' = Cold Insulation Thickness.

Trunnion
2" 3" 4" 6" 8" 10" 12" 16"
Size
Mark 6 Thk. Sq. 6 Thk. Sq. 6 Thk. Sq. 6 Thk. Sq. 6 Thk. Sq. 6 Thk. Sq. 6 Thk. Sq. 6 Thk. Sq.
No. 1 Plate Plate Plate Plate Plate Plate Plate Plate
Area
400 625 755 1225 1765 2255 2755 3660
(cm²)
Dimension
200 250 275 350 420 475 525 605
A'

Assembly Tag No: - CBS1 - X


Detail No Trunnion Size
SUPPORT No CBS1
SUPPORT TYPE Base Support for Cold Insulated Lines Sheet H8
TRUNNION SIZE 2" - 16"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Extend Cold Insulation to end


of Trunnion

For Trunnion details


refer to Isometric
1
CS1
(Ref.)
A

6mm Dia. Weep


Hole. Seal with
Mastic after
Welding

Existing
Steel

250 1000
(Max.)

NOTE
1. Unless otherwise advised by Piping Stress, the trunnion
sizes that shall be used are those listed below.

Pipe
2",3" 4" 6" 8" 10" 12",14" 16", 18" 20", 24"
Size
Trunnion
2" 3" 4" 6" 8" 10" 12" 16"
Size
Mark 6 Thk. Sq. 6 Thk. Sq. 6 Thk. Sq. 6 Thk. Sq. 6 Thk. Sq. 6 Thk. Sq. 6 Thk. Sq. 6 Thk. Sq.
No. 1 Plate Plate Plate Plate Plate Plate Plate Plate
Area
400 625 755 1225 1765 2255 2755 3660
(cm²)
Dimension
200 250 275 350 420 475 525 605
A'

Assembly Tag No: - CTS1 - X


Detail No Pipe Size
SUPPORT No CTS1
SUPPORT TYPE Trunnion Support for Cold Insulated Lines Sheet H9
PIPE SIZE 2" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Trim to suit and


2 2 weld to existing
steel or vessel clip

130

Elevation

L
K

Guides shall be Alternative


welded 20mm below connection
top face of angle. to steel
3 (Elevation) 20
10 See Note 1 L
(typ)

3 Gap 3 Gap 0°
(typ)
(typ)

A
Field weld
bracing where req'd
30 30° 0 60°

30
Plan Bracing req'd when this
A dimension > 300mm

NOTE
1. For details of Cold Double Shoe see CS3.
2. For Pipes with an Insulation Thickness of 50mm and below use pipe support CVG1.
For Pipes with an Insulation Thickness of between 60mm and 100mm use pipe support CVG2.
For Pipes with an Insulation Thickness of 110mm and above use pipe support CVG3.

Assembly Tag No: - CVG1 - X

Detail No. Pipe Size

SUPPORT No CVG1, CVG2, CVG3


SUPPORT TYPE 4- Directional Vertical Guide for Cold Insulated Lines Sheet H10
PIPE SIZE 8" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Pipe Pipe Mark Mark Mark Maximum Horizontal


Size O.D. No. 1 Length No. 2 Length No.3 Loads (KN)
8" 219 2500 2300
10" 273 UPN 160 2500 2470 5
12" 324 3080 2630 10 Thk
14" 356 3080 UPN 100 2625 Plate
16" 406 3500 2890 8
18" 457 3500 3260 Area =
20" 508 UPN 200 4040 3500 36 cm2
22" 559 4040 3680 10
24" 610 4040 3850

Pipe Dimensions
Size CVG1 CVG2 CVG3 All Pipe Supports
Dimn. 'A' Dimn. 'A' Dimn. 'A' 'K' 'L' Max.
8" 425 525 - 1250 900
10" 479 579 - 1250 900
12" - 630 - 1540 1100
14" - 662 - 1540 1100
16" - 712 - 1750 1200
18" - 763 863 1750 1200
20" - 814 914 2020 1400
22" - 865 965 2020 1400
24" - 916 1016 2020 1400

Assembly Tag No: - CVG1 - X

Detail No. Pipe Size

SUPPORT No CVG1
SUPPORT TYPE 4- Directional Vertical Guide for Cold Insulated Lines Sheet H11
PIPE SIZE 8" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Trim to suit and


2 2 weld to existing
steel or vessel clip

130

Elevation

L
K

For shoe orientation Alternative


refer to isometric connection
to steel
(Elevation) 20
10 See Note 1 L
(typ)

3 Gap 0°
(typ)

A
Field weld
bracing where req'd
30° 0 60°

Plan Bracing req'd when this


A dimension > 300mm

NOTE
1. For details of Cold Double Shoe see CS3.
2. For Pipes with an Insulation Thickness of 50mm and below use pipe support CVG4.
For Pipes with an Insulation Thickness of between 60mm and 100mm use pipe support CVG5.
For Pipes with an Insulation Thickness of 110mm and above use pipe support CVG6.

Assembly Tag No: - CVG4 - X

Detail No. Pipe Size

SUPPORT No CVG4, CVG5, CVG6


SUPPORT TYPE 2- Directional Vertical Guide for Cold Insulated Lines Sheet H12
PIPE SIZE 8" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Pipe Pipe Mark Mark Maximum Horizontal


Size O.D. No. 1 Length No. 2 Length Loads (KN)
8" 219 2500 2300
10" 273 UPN 160 2500 2470 5
12" 324 3080 2630
14" 356 3080 UPN 100 2625
16" 406 3500 2890 8
18" 457 3500 3260
20" 508 UPN 200 4040 3500
22" 559 4040 3680 10
24" 610 4040 3850

Pipe Dimensions
Size CVG4 CVG5 CVG6 All Pipe Supports
Dimn. 'A' Dimn. 'A' Dimn. 'A' 'K' 'L' Max.
8" 425 525 - 1250 900
10" 479 579 - 1250 900
12" - 630 - 1540 1100
14" - 662 - 1540 1100
16" - 712 - 1750 1200
18" - 763 863 1750 1200
20" - 814 914 2020 1400
22" - 865 965 2020 1400
24" - 916 1016 2020 1400

Assembly Tag No: - CVG4 - X

Detail No. Pipe Size

SUPPORT No CVG4, CVG5, CVG6


SUPPORT TYPE 2- Directional Vertical Guide for Cold Insulated Lines Sheet H13
PIPE SIZE 8" - 24"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

20 70 20 Stack as 55
Shown
X
4 5 6 1

3
7

'A'
Typ.
25

1
X 2
65 Section X-X
130

Pipe Mark No.1 Total Mark No.2 M.T.O. Mark No.3 Total Mark No.4 No. Off
Size Length Area (cm²) Length
¾" 100x100 260 6Thk. 81 M10 Stud 230 M10 Anco 4
1" x10L 260 Plate 81 Bolt 260 Self Lock 4
1½" 260 81 290 Nut 4

Pipe Mark No.5 No. Off Mark No.6 No. Off Mark No.7 No. Off
Size
¾" M10 4 M10 Compression 6 Fabreeka Nitrile 21 2
1" Plain 4 Washer or 6 Ply Pad 70 x 90 2
1½" Washer 4 Similar 6 or equivalent 2

NOTES:
Pipe Dimension 1- Field procedure for tightening bolts:
Size A -Tighten all nuts by hand (finger Tight)
¾" 115 -Turn nuts an additional 1/2 turn for pipes 2" - 4"
1" 130 -Turn nuts an additional 1/4 turn for pipes 6" - 12"
1½" 145 2- Bond Nitrile Pad to Steel using Epoxy Adhesive
TX528 or equivalent
Assembly Tag No: - HD1 - X

Detail No. Pipe Size

SUPPORT No HD1
SUPPORT TYPE Hold Down for Uninsulated Pipes Sheet H14
PIPE SIZE ¾" - 1½"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
C C

10
L L

'T'
2 1

'E'
'E'

'F'
'F'

1 Hole 'H' Dia. 'A' 1 Hole 'H' Dia. 'A' 1


Note
Note
For Use With No Gusset Required
6" to 12". For 2" to 4".

10 Bond to
Mark No.1
Min Bend 8 9
radius = 1.5T 'C' 'B' 'C'

7
'R'
13

'T'

'D'
13
21

Existing Steel
6
3 4 5
Bond to Drill 18 dia hole
Mark No.4 in existing steel

Pipe Dimensions
Size A B C D E F H
2" 97 76 90 17 60 30 18
3" 111 105 90 32 60 30 18
4" 124 130 90 44 60 30 18
6" 162 191 98 71 90 30 18
8" 187 241 98 97 90 30 18
10" 211 295 98 124 90 30 18
12" 257 352 113 149 90 30 18

Pipe Dimensions
Size R T
2" 32 6 NOTES:
3" 46 6 1- Field procedure for tightening bolts:
4" 59 6 -Tighten all nuts by hand (finger Tight)
6" 86 10 -Turn nuts an additional 1/2 turn
8" 111 10 for pipes 2" - 4"
10" 138 10 -Turn nuts an additional 1/4 turn
12" 164 12 for pipes 6" - 12"
Assembly Tag No: - HD1 - X
Detail No. Pipe Size

SUPPORT No HD1
SUPPORT TYPE Hold Down Support for Uninsulated Pipes Sheet H15
PIPE SIZE 2" - 12"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Pipe Mark Total Mark M.T.O. Mark No. Off Mark M.T.O.
Size No. 1 Length No. 2 Area(cm²) No. 3 No. 4 Area(cm²)
2" 60 x 6 330 2 165
3" Thk. Plate 410 2 185
4" 470 M16 x 2 6Thk. 200
6" 90 x 10 630 10Thk. 70 120Lg. 2 Galvanised 345
8" Thk. Plate 760 Plate 95 Bolt 2 Plate 390
10" 900 120 2 440
12" 90 x 12 1060 12 Thk. 170 2 515
Thk. Plate Plate

Pipe Mark M.T.O. Mark M.T.O. Mark No.


Size No. 5 Area(cm²) No. 6 Area(cm²) No. 7 Off
2" 12Thk. 165 165 2
3" Kinetics 185 185 2
4" Molded 200 1.5mm 200 See 2
6" Fibreglass 345 Thick 345 Note 1 2
8" Pad Type 390 PTFE 390 2
10" S-40 440 440 2
12" Density 515 515 2

Pipe Mark No. Mark No. Mark M.T.O.


Size No. 8 Off No. 9 Off No. 10 Area(cm²)
2" 2 2 65
3" 2 2 95
4" M16 2 M16 2 1.5mm 120
6" Nut 2 Self Lock 2 Thick 240
8" 2 Nut 2 PTFE 310
10" 2 2 385
12" 2 2 460

Note
1. 6Thk. Galvanized Steel Plate, Bonded to 12Thk. Flexoply Isolation
Washer Impregnated in Neoprene and Hot Dipped in Plastisol or Equal.

SUPPORT No HD1
SUPPORT TYPE Hold Down Guide for Uninsulated Pipes Sheet H16
PIPE SIZE 2" - 12"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2
C C

10
L L

'T'
4 2

'E'
'E'

'F'
'F'

1 Hole 'H' Dia. 'A' 1 Hole 'H' Dia. 'A' 2


Note
Note
For Use With No Gusset Required
6" to 12". 12 Bond to
For 2" to 4".
Mark No.2
Min Bend 9 10
radius = 1.5T 'C' 'B' 'C'

11
'R' 55
13

'T'

'D'
13
21 5
1

3
8 10 1 Gusset Req'd.
(typ) Pipe Size 2" to 4".
'I' 'I'
6 7 3 Gussets Req'd.
Bond to Mark No.6 Pipe Size 6" to 12"

Pipe Dimensions
Size A B C D E F H
2" 97 76 90 17 60 30 18
3" 111 105 90 32 60 30 18
4" 124 130 90 44 60 30 18
6" 162 191 98 71 90 30 18
8" 187 241 98 97 90 30 18
10" 211 295 98 124 90 30 18
12" 257 352 113 149 90 30 18

Pipe Dimensions
Size I R T
2" 140 32 6 NOTES:
3" 150 46 6 1- Field procedure for tightening bolts:
4" 165 59 6 -Tighten all nuts by hand (finger Tight)
6" 205 86 10 -Turn nuts an additional 1/2 turn
8" 230 111 10 for pipes 2" - 4"
10" 255 138 10 -Turn nuts an additional 1/4 turn
12" 300 164 12 for pipes 6" - 12"
Assembly Tag No: - HD2 - X
Detail No. Pipe Size

SUPPORT No HD2
SUPPORT TYPE Hold Down Guide for Uninsulated Pipes Sheet H17
PIPE SIZE 2" - 12"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Pipe Mark Total Mark Total Mark M.T.O. Mark M.T.O.


Size No. 1 Length No. 2 Length No. 3 Area(cm²) No. 4 Area(cm²)
2" 280 60 x 6 330 81
3" 300 Thk. Plate 410 81
4" 100x100x 330 470 6Thk. 81
6" 10L 410 90 x 10 630 Plate 162 10Thk. 70
8" 460 Thk. Plate 760 162 Plate 95
10" 510 900 162 120
12" 600 90 x 12 1060 162 12 Thk. 170
Thk. Plate Plate

Pipe Mark M.T.O. Mark M.T.O. Mark M.T.O. Mark No. Off
Size No. 5 Area(cm²) No. 6 Area(cm²) No. 7 Area(cm²) No. 8
2" 165 165 12Thk. 165 2
3" 185 185 Kinetics 185 2
4" 1.5mm 200 6Thk. 200 Molded 200 M16 x 2
6" Thick 345 Galvanised 345 Fibreglass 345 120Lg. 2
8" PTFE 390 Plate 390 Pad Type 390 Bolt 2
10" 440 440 S-40 440 2
12" 515 515 Density 515 2

Pipe Mark No. Mark No. Mark No. Mark M.T.O.


Size No. 9 Off No. 10 Off No. 11 Off No. 12 Area(cm²)
2" 2 2 2 65
3" 2 2 2 95
4" M16 2 M16 2 See 2 1.5mm 120
6" Nut 2 Self Lock 2 Note 1 2 Thick 240
8" 2 Nut 2 2 PTFE 310
10" 2 2 2 385
12" 2 2 2 460

Note
1. 6Thk. Galvanized Steel Plate, Bonded to 12Thk. Flexoply Isolation
Washer Impregnated in Neoprene and Hot Dipped in Plastisol or Equal.

SUPPORT No HD2
SUPPORT TYPE Hold Down Guide for Uninsulated Pipes Sheet H18
PIPE SIZE 2" - 12"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

'H'
4

'H'
'B' 20
Typ. Typ. 300
'A'

'C'
5 55
7 40 6 40 1
A

10
(typ)
8

'E'
9

10 1
Typ.
A 'D' Section A-A
5 6

Pipe Dimension
Size A B C D E H
1" 100 35 360 110 270 100
1½" 100 30 380 110 290 100
2" 100 25 390 110 300 100
3" 100 20 440 110 330 100
4" 100 20 480 110 355 100
6" 100 20 540 110 410 100
8" 200 30 590 110 460 100
10" 200 30 660 110 515 100
12" 250 30 710 110 565 100

NOTES: 1- Bond Nitrile Pad to Steel using Epoxy Adhesive TX528 or equivalent
2- Field procedure for tightening bolts:
-Tighten all nuts by hand (finger Tight)
-Turn nuts an additional 1/2 turn for pipes 2" - 4"
-Turn nuts an additional 1/4 turn for pipes 6" - 12"

Assembly Tag No: - HD3 - X


Detail No. Pipe Size

SUPPORT No HD3
SUPPORT TYPE Hold Down for Insulated Pipes Sheet H19
PIPE SIZE 1" - 12"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Pipe Mark Total Mark Total Mark M.T.O. Mark M.T.O.


Size No. 1 Length No. 2 Length No. 3 Area(cm²) No. 4 Area(cm²)
1" 580 515 1140 120
1½" 600 555 1140 160
2" 610 575 1140 210
3" 100x100x 660 M16 Stud 635 10 Thk. 1140 10 Thk. 245
4" 10L 700 Bolt 685 Plate 1140 Plate 240
6" 760 795 1140 230
8" 810 895 1740 645
10" 880 1005 1740 610
12" 930 1105 2040 920

Pipe Mark M.T.O. Mark No. Off Mark No. Off


Size No. 5 Area(cm²) No. 6 No. 7
1" 325 Fabreeka 2 4
1½" 325 Nitrile 21 2 4
2" 325 Ply Pad 2 M16 4
3" 10 Thk. 325 150x90 2 Self Lock 4
4" Plate 325 or equiv. 2 Nut or 4
6" 325 Fabreeka 2 equivalent 4
8" 325 Nitrile 21 2 4
10" 325 Ply Pad 2 4
12" 325 300x90 2 4
or equiv.

Pipe Mark No. Off Mark No. Off


Size No. 8 No. 9
1" 4 6
1½" 4 6
2" M16 4 M16 6
3" Plain 4 Compr'sn 6
4" Washer 4 Washer 6
6" 4 or Similar 6
8" 4 6
10" 4 6
12" 4 6

SUPPORT No HD3
SUPPORT TYPE Hold Down for Insulated Pipes Sheet H20
PIPE SIZE 1" - 12"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

C C

10
'T'
2 L 1 L

'E'
'E'

'F'

'F'
25 25
'H'

'H'
= = = = 1
Note 'A' 'A'
For Use With Note
6" to 12". No Gusset Required
10 Bond to For 2" to 4".
Mark No.1
Min Bend 8 9
radius = 1.5T 'C' 'B' 'C'

7
'R'
13

'T'

'D'
13
21

Existing Steel
6
3 4 5
Bond to Drill 18 dia hole
Mark No.4 in existing steel

Pipe Dimensions
Size A B C D E F H
2" 110 76 118 17 60 30 18
3" 124 105 120 32 60 30 18
4" 137 130 120 44 60 30 18
6" 168 191 125 71 90 30 18
8" 194 241 125 97 90 30 18
10" 224 295 125 124 90 30 18
12" 270 352 137 149 90 30 18

Pipe Dimensions
Size R T
2" 32 6 NOTES:
3" 46 6 1- Field procedure for tightening bolts:
4" 59 6 -Tighten all nuts by hand (finger Tight)
6" 86 10 -Turn nuts an additional 1/2 turn
8" 111 10 for pipes 2" - 4"
10" 138 10 -Turn nuts an additional 1/4 turn
12" 164 12 for pipes 6" - 12"
Assembly Tag No: - HDS1 - X
Detail No. Pipe Size

SUPPORT No HDS1
SUPPORT TYPE Slotted Hold Down Support for Uninsulated Pipes Sheet H21
PIPE SIZE 2" - 12"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Pipe Mark Total Mark M.T.O. Mark No. Off Mark M.T.O.
Size No. 1 Length No. 2 Area(cm²) No. 3 No. 4 Area(cm²)
2" 60 x 6 340 2 190
3" Thk. Plate 370 2 210
4" 390 M16 x 2 6Thk. 225
6" 90 x 10 460 10Thk. 70 120Lg. 2 Galvanised 400
8" Thk. Plate 510 Plate 95 Bolt 2 Plate 440
10" 590 120 2 490
12" 90 x 12 650 12 Thk. 170 2 565
Thk. Plate Plate

Pipe Mark M.T.O. Mark M.T.O. Mark No.


Size No. 5 Area(cm²) No. 6 Area(cm²) No. 7 Off
2" 12Thk. 190 190 2
3" Kinetics 210 210 2
4" Molded 225 1.5mm 225 See 2
6" Fibreglass 400 Thick 400 Note 1 2
8" Pad Type 440 PTFE 440 2
10" S-40 490 490 2
12" Density 565 565 2

Pipe Mark No. Mark No. Mark M.T.O.


Size No. 8 Off No. 9 Off No. 10 Area(cm²)
2" 2 2 65
3" 2 2 95
4" M16 2 M16 2 1.5mm 120
6" Nut 2 Self Lock 2 Thick 240
8" 2 Nut 2 PTFE 310
10" 2 2 385
12" 2 2 460

Note
1. 6Thk. Galvanized Steel Plate, Bonded to 12Thk. Flexoply Isolation
Washer Impregnated in Neoprene and Hot Dipped in Plastisol or Equal.

SUPPORT No HDS1
SUPPORT TYPE Slotted Hold Down Support for Uninsulated Pipes Sheet H22
PIPE SIZE 2" - 12"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3
C CL

10
'T'
4 L 2

'E'
'E'

'F'

'F'
25 25
'H'

'H'
= = = = 2
'A' 'A'
Note
For Use With Note
6" to 12". 12 Bond to No Gusset Required
Mark No.2 For 2" to 4".
Min Bend
'C' 'B' 'C' 9 10
radius = 1.5T

11
'R' 55
13

'T'

'D'
13
21 5
1

3
8 10 1 Gusset Req'd.
(typ) Pipe Size 2" to 4".
'I' 'I'
6 7 3 Gussets Req'd.
Bond to Mark No.6 Pipe Size 6" to 12"

Pipe Dimensions
Size A B C D E F H
2" 110 76 118 17 60 30 18
3" 124 105 120 32 60 30 18
4" 137 130 120 44 60 30 18
6" 168 191 125 71 90 30 18
8" 194 241 125 97 90 30 18
10" 224 295 125 124 90 30 18
12" 270 352 137 149 90 30 18

Pipe Dimensions
Size I R T NOTES:
2" 170 32 6 1- Field procedure for tightening bolts:
3" 185 46 6 -Tighten all nuts by hand (finger Tight)
4" 195 59 6 -Turn nuts an additional 1/2 turn
6" 230 86 10 for pipes 2" - 4"
8" 255 111 10 -Turn nuts an additional 1/4 turn
10" 285 138 10 for pipes 6" - 12"
12" 325 164 12
Assembly Tag No: - HDS2 - X
Detail No. Pipe Size

SUPPORT No HDS2
SUPPORT TYPE Slotted Hold Down Support for Uninsulated Pipes Sheet H23
PIPE SIZE 2" - 12"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 3

Pipe Mark Total Mark Total Mark M.T.O. Mark M.T.O.


Size No. 1 Length No. 2 Length No. 3 Area(cm²) No. 4 Area(cm²)
2" 340 60 x 6 390 81
3" 370 Thk. Plate 470 81
4" 100x100x 390 535 6Thk. 81
6" 10L 460 90 x 10 695 Plate 162 10Thk. 70
8" 510 Thk. Plate 825 162 Plate 95
10" 570 965 162 120
12" 650 90 x 12 1125 162 12 Thk. 170
Thk. Plate Plate

Pipe Mark M.T.O. Mark M.T.O. Mark M.T.O. Mark No. Off
Size No. 5 Area(cm²) No. 6 Area(cm²) No. 7 Area(cm²) No. 8
2" 190 190 12Thk. 190 2
3" 210 210 Kinetics 210 2
4" 1.5mm 225 6Thk. 225 Molded 225 M16 x 2
6" Thick 400 Galvanised 400 Fibreglass 400 120Lg. 2
8" PTFE 440 Plate 440 Pad Type 440 Bolt 2
10" 490 490 S-40 490 2
12" 565 565 Density 565 2

Pipe Mark No. Mark No. Mark No. Mark M.T.O.


Size No. 9 Off No. 10 Off No. 11 Off No. 12 Area(cm²)
2" 2 2 2 65
3" 2 2 2 95
4" M16 2 M16 2 See 2 1.5mm 120
6" Nut 2 Self Lock 2 Note 1 2 Thick 240
8" 2 Nut 2 2 PTFE 310
10" 2 2 2 385
12" 2 2 2 460

Note
1. 6Thk. Galvanized Steel Plate, Bonded to 12Thk. Flexoply Isolation
Washer Impregnated in Neoprene and Hot Dipped in Plastisol or Equal.

SUPPORT No HDS2
SUPPORT TYPE Slotted Hold Down Support for Uninsulated Pipes Sheet H24
PIPE SIZE 2" - 12"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0
C C

10
L L

'T'
2 1

'E'
'E'

'F'
'F'

1 Hole 'H' Dia. 'A' 1 Hole 'H' Dia. 'A' 1


Note Note
For Use With No Gusset Required
6" & 8". For 1½" to 4".

Min Bend
radius = 1.5T 'B' 'B'

'R'
'T'

'C'
'D'
5

4 1 Hole 'H' dia. in Existing Steel


Existing Steel
3
Typ.

Pipe Dimensions
Size A B C D E F H
1½" 60 80 22 2 60 30 14
2" 70 100 28 2 60 30 14
3" 99 137 41 3 60 30 18
4" 108 146 54 3 60 30 18
6" 155 200 81 3 90 30 26
8" 180 230 105 4 90 30 26

Pipe Dimensions
Size R T
1½" 25 6
2" 31 6
3" 46 6
4" 58 10
6" 85 10
8" 111 10

Assembly Tag No: - AS1 - X


Detail No. Pipe Size

SUPPORT No AS1
SUPPORT TYPE Anchor Strap for Uninsulated Galvanised Pipe Sheet H25
PIPE SIZE 1½" - 8"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

Pipe Mark Total Mark M.T.O. Mark No. Off Mark No. Off
Size No. 1 Length No. 2 Area(cm²) No. 3 No. 4
1½" 60 x 6 200 M12 x 2 M16 x
2" Thk. Plate 300 70Lg. 2 80Lg.
3" 420 Bolt C/W Bolt C/W 2
4" 480 Nut & Nut & 2
6" 90 x 10 670 10Thk. 160 Washer Washer
8" Thk. Plate 810 Plate 210

Pipe Mark No. Off


Size No. 5
1½" M24 x
2" 100Lg.
3" Bolt C/W
4" Nut &
6" Washer 2
8" 2

SUPPORT No AS1
SUPPORT TYPE Anchor Strap for Uninsulated Galvanised Pipe Sheet H26
PIPE SIZE 1½" - 8"
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Welded Shoe S1, S5, S9 Welded Shoe S1, S5, S9 Welded Shoe S1, S5 Welded Shoe S2, S6, S10 Welded Shoe S2, S6, S10 Welded Shoe S2, S6
Standard Length. Pipe Size ½"-6" Standard Length. Pipe Size 8"-24" Standard Length. Pipe Size 26"-40" Long. Pipe Size ½"-6" Long. Pipe Size 8"-24" Long. Pipe Size 26"-92"
Sheet A1 Sheet A2 Sheet A3 Sheet A4 Sheet A5 Sheet A6 & A7

Clamped Shoe S3, S7, S11 Clamped Shoe S3, S7, S11 Clamped Shoe S4, S8, S12 Clamped Shoe S4, S8, S12 Clamped Shoe S103, S107, S111 Clamped Shoe S103, S107, S111
Standard Length. Pipe Size ½"-6" Standard Length. Pipe Size 8"-24" Long. Pipe Size ½"-6" Long. Pipe Size 8"-24" For St. Stl. Pipe. Pipe Size ½"-6" For St. Stl. Pipe. Pipe Size 8"-30"
Sheet A8 Sheet A9 Sheet A10 Sheet A11 Sheet A14 Sheet A15

Clamped Shoe S104, S108, S112 Clamped Shoe S104, S108, S112 PTFE Isolator Pad for Stainless Steel Pick-Up for Insulated Pipe Pick-Up for Uninsulated Pipe Packing Plate types for gaps up to
Long. For St. Stl. Pipe. Pipe Size Long. For St. Stl. Pipe. Pipe Size Pipe. S113. Pipe Size ½"-12" S114. Pipe Size 3" Max (Supported S115. Pipe Size 3" Max. (Supported 20mm. Pipe Size ½"-42"
½"-6". Sheet A16 8"-30". Sheet A17 Sheet A18 Pipe). Sheet A19 Pipe). Sheet A20 Sheet A21 & A22

PTFE for Pipe Shoe PTFE for Pipe Shoe Packing Plate types for gaps 21mm to Packing Plate types for gaps 61mm PTFE for Long Pipe Shoe PTFE for Long Pipe Shoe
S19. Pipe Size ½"-24" S19. Pipe Size 26"-88" 60mm. Pipe Size ½"-42" to 80mm. Pipe Size ½"-42" S20. Pipe Size ½"-24" S20. Pipe Size 26"-88"
Sheet A12 Sheet A13 Sheet A23 & A24 Sheet A25 & A26 Sheet A27 Sheet A28

ATTACHMENT A - PIPE SUPPORT SELECTION CHART (SHOES, PTFE, PICK-UP, PACKING) SHEET No. J1A
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

Pipe Shoe for SECT Traced Piping Long Welded Shoe. S13, S14 Packing Support for gaps from 21mm Stiffening Ring Double Pipe Shoe for SECT Traced Puddle Flange for Sump Covers
S21. All Sizes For Pipe Spec. 150H26, 150K26 to 60mm. PK3 SR1, SR101. Pipe Size 36" - 92" Piping. S22. All Sizes PF1, PF101. Pipe Size ¾" - 12"
Sheet A29 Pipe Size 36"- 40" Sheet A30 & A31 Pipe Size 44" - 92". Sheet A32 Sheet A33 Sheet A34 Sheet A35

Welded Shoe for Contra Traced Pipes


S15. Pipe Size 28".
Sheet A36

ATTACHMENT A - PIPE SUPPORT SELECTION CHART (SHOES, PTFE, PICK-UP, PACKING) SHEET No. J1B
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Line Stop for Uninsulated Pipe Line Stop for Uninsulated Pipe Line Stop for Uninsulated Pipe Line Stop for Insulated Pipe Line Stop for Insulated Pipe Line Stop for Insulated Pipe
DA1. Pipe Size ½"-4" DA1. Pipe Size 6"-14" DA1. Pipe Size 16"-40" DA2, DA3. Pipe Size ½"-4" DA2, DA3. Pipe Size 6"-24" DA2. Pipe Size 26"-92"
Sheet B1 Sheet B2 Sheet B3 Sheet B4 Sheet B5 Sheet B6 & B7

Guide for Insulated Pipe Guide for Uninsulated Pipe Guide for Uninsulated Pipe Guide (Hold-down) for Insulated Guide for Uninsulated Vertical Pipe Guide for Uninsulated Vertical Pipe
HG1. Pipe Size ½"-92" HG2. Pipe Size ½"-14" HG2. PipeSze 16" - 40" Pipe. HG3. Pipe Size ½"-6" 4 Way. St.Stl. VG104. 2 Way. St.Stl. VG107 & VG108
Sheet B8 Sheet B9 Sheet B10 Sheet B11 Pipe Size 4"-24". Sheet B32 & B33 Pipe Size 4"-24". Sheet B32 & B33

PLAN PLAN PLAN


PLAN PLAN PLAN

Guide for Uninsulated Vertical Pipe Guide for 2 or more Vertical Pipes Guide for all Vertical Pipes Guide for Uninsulated Vertical Pipe 4 Guide for Vertical Pipe - 4 Way Guide for Vertical Pipe - 4 Way
VG1. Pipe Size ½"-2" VG2. Pipe Size ½"-2" VG3. Pipe Size ½"-6" Way. VG4. Pipe Size 8"-24" Insulation ≤ 75mm Thk. VG5 Insulation ≥ 75mm Thk. VG6
Sheet B12 Sheet B13 Sheet B14 Sheet B15 & B16 Pipe Size 8"-24". Sheet B15 & B16 Pipe Size 8"-24". Sheet B15 & B16

PLAN PLAN PLAN PLAN

Guide for Uninsulated Vertical Pipe Guide for Uninsulated Vertical Pipe Guide for Vertical Pipe - 2 Way Guide for Vertical Pipe - 2 Way Rigid Strut with Trunnion and Clamp Rigid Strut with Shoe
2 Way. VG7. Pipe Size 4"-24" 2 Way. VG8. Pipe Size 4"-24" Insulation ≤ 75mm Thk. VG9 Insulation ≥ 75mm Thk. VG10 RS1. RS2.
Sheet B17 & B18 Sheet B17 & B18 Pipe Size 4"-24". Sheet B17 & B18 Pipe Size 4"-24". Sheet B17 & B18 Pipe Size All Sizes. Sheet B26 Pipe Size All Sizes. Sheet B27

ATTACHMENT B - PIPE SUPPORT SELECTION CHART (LINE STOPS, GUIDES, RIGID STRUTS) SHEET No. J2
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Plan

Cantilever Support for Vertical Pipe Braced Cantilever Support for Horizontal Frame Support and Guide Braced Horizontal Frame Support for Support from Vessel for Vertical Pipe Braced Support from Vessel for
VS1. Pipe Size ½"-8" Vertical Pipe. VS2. Pipe Size 2"-24" for Vertical Pipe. VS3. Vertical Pipe. VS4. Pipe Size ½"-24" VS5. Pipe Size 2" - 10" Vertical Pipe. VS6. Pipe Size 4" - 24"
Sheet B19 Sheet B20 Pipe Size ½"-24". Sheet B21 Sheet B22 Sheet B23 Sheet B24 & B25

Line Stop for Non-Insulated St.Stl. Line Stop for Insulated St.Stl. Line Stop, Non-Insul Galvanised pipes Line Stop, Insulated Galvanised pipes Guide for Uninsulated St. Stl. Pipe Guide for Uninsulated St. Stl. Pipe
Pipes. DA101. Pipe Size ¾" - 1½" Pipes. DA102. Pipe Size ½" - 1½" DA201. Pipe Size ½" - 3" DA202. Pipe Size ½" - 3" 4 Way. VG104. Pipe Size 4" - 24" 2 Way. VG107. Pipe Size 4" - 24"
Sheet B28 Sheet B29 Sheet B30 Sheet B31 Sheet B32 & B33 Sheet B32 & B33

Guide for Uninsulated St. Stl. Pipe Line Stop for Uninsulated Pipes on Line Stop for Uninsulated Pipes on Line Stop for Uninsulated Pipes on Line Stop for Insulated Pipes on Line Stop for Insulated Pipes on
2 Way. VG108. Pipe Size 4" - 24" Sleepers < 600mm . DA4 Sleepers < 600mm . DA4 Sleepers < 600mm . DA4 Sleepers < 600mm . DA5, DA6 Sleepers < 600mm . DA5, DA6
Sheet B32 & B33 Pipe Size ½" - 4" Sheet B34 Pipe Size 6" - 14" Sheet B35 Pipe Size 16" - 40" Sheet B36 Pipe Size ½" - 4" Sheet B37 Pipe Size 6" - 24" Sheet B38

Line Stop for Insulated Pipes on Line Stop for Uninsulated Pipes on Line Stop for Uninsulated Pipes on Line Stop for Uninsulated Pipes on Line Stop for Insulated Pipes on Line Stop for Insulated Pipes on
Sleepers < 600mm . DA5, DA6 Sleepers > 600mm . DA7 Sleepers > 600mm . DA7 Sleepers > 600mm . DA7 Sleepers > 600mm . DA10 Sleepers > 600mm . DA10
Pipe Size 26"-40" Sheet B48 & B49 Pipe Size ½" - 4" Sheet B39 Pipe Size 6" - 14" Sheet B40 Pipe Size 16" - 40" Sheet B41 Pipe Size ½" - 4" Sheet B44 Pipe Size 6" - 16" Sheet B45

ATTACHMENT B - PIPE SUPPORT SELECTION CHART (BRACKETS WITH TRUNNIONS; STEEL, STAIN. STEEL AND GALVANISED LINE STOPS ON STEEL/SLEEPERS) SHEET No. J3A
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

Line Stop for SECT Traced Piping Line Stop for SECT Traced Piping Anchor Shoe for SECT Traced Piping Anchor Shoe for SECT Traced Piping Line Stop for Pipe Spec. 150H26, Line Stop for Acoustic Insulated
on Steel. DA8 on Sleepers. DA9 on Steel. SAS1 on Sleepers. SAS2 150K26. DA11, DA12 Pipe. DA13
Pipe Size 6" Sheet B42 Pipe Size 6" Sheet B43 Pipe Size All Sizes Sheet B56 Pipe Size All Sizes Sheet B57 Pipe Size 36"- 40" Sheet B46 & B47 Pipe Size ½"- 4" Sheet B50

Line Stop for Acoustic Insulated Line Stop for Acoustic Insulated Line Stop for Uninsulated or PPC Pipe, Line Stop for Uninsulated or PPC Pipe
Pipe. DA13 Pipe. DA13 Des. Temp. -60°C or below. Des. Temp. -60°C or below.
Pipe Size 6"- 24" Sheet B51 Pipe Size 26"- 40" Sheet B52 & B53 DA103 Pipe Size 8"-14" Sheet B54 DA103 Pipe Size 16"-24" Sheet B55

ATTACHMENT B - PIPE SUPPORT SELECTION CHART (BRACKETS WITH TRUNNIONS; STEEL, STAIN. STEEL AND GALVANISED LINE STOPS ON STEEL/SLEEPERS) SHEET No. J3B
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Base Anchor for Non-Adjustable Base Anchor for Adjustable Support Base Guide for Non-Adjustable Base Guide for Adjustable Support
Support. BA1. Pipe Size 2"-40" BA2. Pipe Size 2"-40" Support. BG1. Pipe Size 2"-40" BG2. Pipe Size 2"-40"
Sheet C10 Sheet C11 Sheet C12 Sheet C13

Base Plate from Grade Base Plate from Steelwork Non-Adjustable Base Support for Non-Adjustable Base Support for Non-Adjustable Base Support Adjustable Base Support
BP. Pipe Size 2"-22" BPS. Pipe Size 2"-22" Un-Paved areas. BS4 Paved and non-paved areas. BS5 BS1. Pipe Size 2"-40" BS2. Pipe Size 2"-40"
Sheet C14 Sheet C16 Pipe Size 2"-40". Sheet C15 Pipe Size 2"-40". Sheet C18 Sheet C5 Sheet C6 & C7

PTFE for Existing Base Support PTFE for Existing Base Support Small non-adjustable Base Support
BS3. Pipe Size 2"-22" BS3. Pipe Size 24"-40" BS6. Pipe Size 2" - 40"
Sheet C8 Sheet C9 Sheet C19

Horizontal Trunnion Support from Horizontal Trunnion Support from Horizontal Trunnion Support from Horizontal Trunnion Support from
Pipe (1 Off). T1. Pipe Size 2"-36" Pipe (2 Off). T2. Pipe Size 2"-36" Elbow. T3. Pipe Size 2"-36" Pipe (2 Off) with RePad. T2.
Sheet C1 & C3 Sheet C2 & C3 Sheet C4 & C17 Pipe Size 48"-70" Sheet C20

ATTACHMENT C - PIPE SUPPORT SELECTION CHART (BASE SUPPORTS, BASE SUPPORTS WITH PTFE, TRUNNIONS) SHEET No. J4
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 1

Non-Adjustable Hanger for Non-Adjustable Hanger for Uninsulated Non-Adjustable Hanger for Uninsulated Non-Adjustable Hanger for Insulated Non-Adjustable Hanger for Insulated Adjustable Hanger for Uninsulated
Uninsulated Pipe . HR1 (LightLoads) Pipe. HR2 (Heavy Loads) Pipe. HR3 (Light Loads) Pipe. HR4 (Light Loads) Pipe. HR5 (Heavy Loads) Pipe. HR6 (Light Loads)
Pipe Size 1/2"-30". Sheet D1 & D2 Pipe Size 1/2"-30". Sheet D1 & D2 Pipe Size 1/2"-30". Sheet D1 & D2 Pipe Size 1/2"-24". Sheet D3 & D4 Pipe Size 1/2"-24". Sheet D3 & D4 Pipe Size 1/2"-30". Sheet D5 & D6

Adjustable Hanger for Uninsulated Pipe. Adjustable Hanger for Uninsulated Pipe.Adjustable Hanger for Insulated Pipe. Adjustable Hanger for Insulated Pipe. Non-Adjustable Hanger for Uninsulated Non-Adjustable Hanger for Uninsulated
HR7 (Heavy Loads) HR8 (Light Loads) HR9 (Light Loads) HR10 (Heavy Loads) St. Steel Pipe. HR101 (Light Loads) St. Steel Pipe. HR102 (Heavy Loads)
Pipe Size 1/2"-30". Sheet D5 & D6 Pipe Size 1/2"-30". Sheet D5 & D6 Pipe Size 1/2"-24". Sheet D7 & D8 Pipe Size 1/2"-24". Sheet D7 & D8 Pipe Size 1/2"-30". Sheet D9 & D10 Pipe Size 1/2"-30". Sheet D9 & D10

Non-Adjustable Hanger for Insulated Non-Adjustable Hanger for Insulated Adjustable Hanger for Uninsulated Adjustable Hanger for Uninsulated Adjustable Hanger for Insulated Adjustable Hanger for Insulated
St. Steel Pipe. HR104 (Light Loads) St. Steel Pipe. HR105 (Heavy Loads) St. Steel Pipe. HR106 (Light Loads) St. Steel Pipe. HR107 (Heavy Loads) St. Steel Pipe. HR109 (Light Loads) St. Steel Pipe. HR110 (Heavy Loads)
Pipe Size 1/2"-24". Sheet D11 & D12 Pipe Size 1/2"-24". Sheet D11 & D12 Pipe Size 1/2"-30". Sheet D13 & D14 Pipe Size 1/2"-30". Sheet D13 & D14 Pipe Size 1/2"-24". Sheet D15 & D16 Pipe Size 1/2"-24". Sheet D15 & D16

Trapeze Hanger
TH
Pipe Size All Sizes. Sheet D17

ATTACHMENT D - PIPE SUPPORT SELECTION CHART (HANGERS) SHEET No. J5


TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Spring Hanger for Uninsulated Pipe Spring Hanger for Insulated Pipe Spring Hanger for Uninsulated Pipe Spring Hanger for Insulated Pipe Trapeze Spring Hanger from under Trapeze Spring Hanger from top of
SH1 SH2 SH3 SH4 side of steel. SH5 steel. SH6
Pipe Size 2"-30". Sheet D18 Pipe Size 2"-30". Sheet D18 Pipe Size 2"-30". Sheet D19 Pipe Size 2"-30". Sheet D19 Pipe Size All Sizes. Sheet D20 Pipe Size All Sizes. Sheet D21

Trapeze Spring Hanger from under Pedestal Spring Spring Hanger from Top of Steel to Spring Hanger for Cold Insulated Spring Hanger for Cold Insulated Spring Hanger from U/Side of Steel
side of steel. SH7 SH8 Elbow Lug. SH9 Pipe. SH21 Pipe. SH22 to Elbow Lug. SH10
Pipe Size All Sizes. Sheet D22 Pipe Size All Sizes. Sheet D23 Pipe Size All Sizes. Sheet D29 Pipe Size 2"-36" Sheet D30 Pipe Size 2"-36" Sheet D30 Pipe Size All Sizes. Sheet D31

Spring Hanger from U/Side of Steel Spring Hanger from Top of Steel to Constant Spring Hanger from under Constant Spring Hanger from under Constant Spring Hanger from top of Constant Spring Hanger from top of
to Pipe Lug. SH23 Pipe Lug. SH24 side of steel. SH11 side of steel. SH12 steel. SH13 steel. SH14
Pipe Size All Sizes. Sheet D32 Pipe Size All Sizes. Sheet D33 Pipe Size 2"-30". Sheet D24 Pipe Size 2"-30". Sheet D24 Pipe Size 2"-30". Sheet D25 Pipe Size 2"-30". Sheet D25

Constant Spring Hanger from under Constant Spring Hanger from under Constant Spring Hanger from top of Constant Spring Hanger from top of Constant Pedestal Spring Constant Pedestal Spring
side of steel. SH15 side of steel. SH16 steel. SH17 steel. SH18 SH19 SH20
Pipe Size 2"-30". Sheet D26 Pipe Size 2"-30". Sheet D26 Pipe Size 2"-30". Sheet D27 Pipe Size 2"-30". Sheet D27 Pipe Size All Sizes. Sheet D28 Pipe Size All Sizes. Sheet D28

ATTACHMENT D - PIPE SUPPORT SELECTION CHART (SPRING HANGERS) SHEET No. J6A
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

Horizontal Pipe Support for HVAC


Piping-Single Bank. PS15
Pipe Size All Sizes Sht. D34

ATTACHMENT D - PIPE SUPPORT SELECTION CHART (HORIZONTAL PIPE SUPPORT FOR HVAC PIPING-SINGLE BANK) SHEET No. J6B
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 1

Tee Post from Existing Structure Tee Post from Existing Structure Pedestal from Existing Structure Cantilevered Post from Existing Cantilevered Post from Existing Goal Post from Existing Structure
P1 (Angle) P1 (HEA) P2 Structure. P3 (Angle) Structure. P3 (HEA) P4 (Angle)
Pipe Size 1/2" - 2". Sheet E1 Pipe Size All Sizes. Sheet E1 Pipe Size All Sizes. Sheet E2 Pipe Size 1/2" - 2". Sheet E3 Pipe Size All Sizes. Sheet E3 Pipe Sizes 1/2" - 2". Sheet E4

Goal Post from Existing Structure Post from Existing Structure Cantilevered Post from Existing Inverted Tee Post Inverted Tee Post Inverted Cantilevered Support
P4 (HEA) P5 Structure. P6 P7 (Angle) P7 (HEA) P8 (Angle)
Pipe Sizes All Sizes. Sheet E5 Pipe Size All Sizes. Sheet E6 Pipe Size All Sizes. Sheet E7 Pipe Size 1/2" - 2". Sheet E8 Pipe Size 4" & below. Sheet E8 Pipe Size 2" & below. Sheet E9

Inverted Cantilevered Support Inverted Goal Post Inverted Goal Post Inverted Cantilevered Post Inverted Goal Post (Piperacks only) Cantilever Support
P8 (HEA) P9 (Angle) P9 (HEA) P10 P11 P21
Pipe Size All Sizes. Sheet E9 Pipe Size 1/2" - 2". Sheet E10 Pipe Size All Sizes. Sheet E11 Pipe Size All Sizes. Sheet E12 Pipe Size All Sizes. Sheet E13 Pipe Size All Sizes. Sheet E14

Cantilever Support Cantilever Support Cantilever Support Cantilever Support Braced Cantilever Support Braced Cantilever Support
P22 P23 P24 P25 P26 P27
Pipe Size All Sizes. Sheet E15 Pipe Size All Sizes. Sheet E15 Pipe Size All Sizes. Sheet E16 Pipe Size All Sizes. Sheet E16 Pipe Size All Sizes. Sheet E17 Pipe Size All Sizes. Sheet E18

ATTACHMENT E - PIPE SUPPORT SELECTION CHART (TEE POSTS, PEDESTAL, GOAL POSTS, CANTILEVERS, BRACKETS WELDED TO EXIST. STRUCTURE) SHEET No. J7
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 1

Braced Cantilever Support Braced Cantilever Support Braced Cantilever Support Beam Welded to Column Beam Welded to Column Beam Welded to Column
P28 P29 P30 P31 Pipe Size All Sizes P32 Pipe Size All Sizes P33 Pipe Size All Sizes
Pipe Size All Sizes. Sheet E18 Pipe Size All Sizes. Sheet E19 Pipe Size All Sizes. Sheet E19 Sheet E20 & E21 Sheet E20 & E21 Sheet E20 & E21

Beam welded to Beam Beam welded to Beam Beam welded to Beam Cantilevered Welded Beam Cantilevered Welded Beam Cantilevered Welded Beam
P34 Pipe Size All Sizes P35 Pipe Size All Sizes P36 Pipe Size All Sizes P37 Pipe Size All Sizes P38 Pipe Size All Sizes P39 Pipe Size All Sizes
Sheet E22 & E23 Sheet E22 & E23 Sheet E22 & E23 Sheet E24 & E25 Sheet E24 & E25 Sheet E24 & E25

Base Plate for Cantilever to concrete


P20 Pipe Size All Sizes
Sheet E44

ATTACHMENT E - PIPE SUPPORT SELECTION CHART (BRACKETS, WELDED BEAMS TO EXISTING STRUCTURE) SHEET No. J8
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 1

Tee Post from New Paving Tee Post from New Paving Pedestal from New Paving Cantilevered Post from New Paving Cantilevered Post from New Paving Goal Post from New Paving
P41 (Angle) P41 (HEA) P42 P43 (Angle) P43 (HEA) P44 (Angle)
Pipe Size All Sizes. Sheet E26 Pipe Size All Sizes. Sheet E26 Pipe Size All Sizes. Sheet E27 Pipe Size All Sizes. Sheet E28 Pipe Size All Sizes. Sheet E28 Pipe Size 1/2" - 2". Sheet E29

Goal Post from New Paving Post from New Paving Welded Cantilevered Post from New Tee Post for Un-Paved Areas Tee Post for Un-Paved Areas Pedestal for Un-Paved Areas
P44 (HEA) P45 Paving. P46 P51 (Angle) P51 (HEA) P52
Pipe Size 3" & above. Sheet E30 Pipe Size All Sizes. Sheet E31 Pipe Size All Sizes. Sheet E32 Pipe Size All Sizes. Sheet E33 Pipe Size All Sizes. Sheet E33 Pipe Size All Sizes. Sheet E34

SUPPORT
DELETED

Cantilevered Post for Un-Paved Areas Cantilevered Post for Un-Paved Areas Goal Post for Un-Paved Areas Goal Post for Un-Paved Areas Post for Un-Paved Areas Welded Cantilevered Post for Un-
P53 (Angle) (Augered Pile SGI) P53 (HEA) (Augered Pile SGI) P54 (Angle) P54 (HEA) (Augered Pile SGI) P55 (Augered Pile SGI) Paved Areas. P56(Augered Pile SGI)
Pipe Size All Sizes. Sheet E35 Pipe Size All Sizes. Sheet E35 Pipe Size 1/2" - 2". Sheet E36 Pipe Size All Sizes. Sheet E37 Pipe Size All Sizes. Sheet E38 Pipe Size All Sizes. Sheet E39

T-Post for Utility Stations, all areas Pipe Support for Utility Stations Cantilever support for utility stations Support for steam trap manifolds
P60 from Platforms. P61 P62 P63
Pipe Size 1/2" - 2" Sheet E40 Pipe Size 1/2"-2" Sheet E41 Pipe Size 1/2" - 2" Sheet E42 Pipe Size 1/2" - 2" Sheet E43

ATTACHMENT E - PIPE SUPPORT SELECTION CHART (TEE POSTS, GOAL POSTS, CANTILEVERED POSTS FROM GRADE (SGI) AND UTILITY STATION SUPPORTS ) SHEET NO. J9
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 1

T-Post for un-paved areas Post with plate for un-paved areas Cantilevered-Post for un-paved areas Goal-Post for un-paved areas Post for un-paved areas Welded Cantilevered Post for
P71 P72 P73 P74 P75 un-paved areas
Pipe Size-All Sizes Sheet E45 Pipe Size-All Sizes Sheet E46 Pipe Size-All Sizes Sheet E47 Pipe Size-All Sizes Sheet E48 Pipe Size-All Sizes Sheet E49 P76 Pipe size-All Sizes Sheet E50

ATTACHMENT E - PIPE SUPPORT SELECTION CHART (TEE POSTS, GOAL POSTS, CANTILEVERED POSTS FROM GRADE - SGP ) SHEET NO. J10
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 2

Guide/Support from Exist.Steel Anchor/Support from Exist.Steel Guide/Support from Grade Anchor/Support from Grade Anchor Support from Steel for Anchor Support from Grade for
SB1 SB2 SB3 SB4 Vertical Pipe. SB5 Vertical Pipe. SB6
Pipe Size 1/2" - 2". Sheet F1 Pipe Size ½" - 2". Sheet F1 Pipe Size ½" - 2". Sheet F2 Pipe Size ½" - 2". Sheet F2 Pipe Size ½" - 2". Sheet F3 Pipe Size ½" - 2". Sheet F4

Support and Guide for Vertical Pipe Support for Vertical Pipe Guide for Vertical Pipe Guide/Support from Steel for Anchor/Support from Steel for Guide/Support from Grade for
SB7 SB8 SB9 Stainless Steel Pipe. SB101 Stainless Steel Pipe. SB102 Stainless Steel Pipe. SB103
Pipe Size ½" - 2". Sheet F5 Pipe Size ½" - 2". Sheet F6 Pipe Size ½" - 2". Sheet F7 Pipe Size ½" - 2". Sheet F8 Pipe Size ½" - 2". Sheet F8 Pipe Size ½" - 2". Sheet F9

Anchor/Support from Grade for Guide/Support from Steel for Guide/Support from Grade for Support and Guide for Vertical Support for Vertical Stainless Steel Guide for Vertical Stainless Steel
Stainless Steel Pipe. SB104 Stainless Steel Pipe. SB105 Stainless Steel Pipe. SB106 Stainless Steel Pipe. SB107 Pipe. SB108 Pipe. SB109
Pipe Size ½" - 2". Sheet F9 Pipe Size ½" - 2". Sheet F10 Pipe Size ½" - 2". Sheet F11 Pipe Size ½" - 2". Sheet F12 Pipe Size ½" - 2". Sheet F13 Pipe Size ½" - 2". Sheet F14

Cradle C1,C2,C3,C7,C8,C101, Cradle Insulated 'U' Bolt Anchor for Insulated 'U' Bolt Guide for Lifting Lugs for Piping Break-Out Lifting Lugs for Piping Break-Out
C102,C103,C107,C108 C4, C5, C6, C104, 105, C106 Stainless Steel Pipe. UA101 Stainless Steel Pipe. UG101 Spools from an elbow Spools from pipe
Pipe Size 2"-92". Sheet F32,F33,F42 Pipe Size 2"-92". Sheet F34 & F35 Pipe Size ½" - 2". Sheet F36 Pipe Size ½" - 2". Sheet F37 LL1. Pipe Size-All Sizes. Sheet F38 LL2. Pipe Size-All Sizes. Sheet F39

ATTACHMENT F - PIPE SUPPORT SELECTION CHART ('U' BOLT GUIDE/ANCHOR, SHEAR LUG) SHEET No. J11A
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 0

U-Bolt Guide U-Bolt Anchor Welded Gusset Support for Carbon Welded Gusset Support for Carbon Welded Gusset Support for Carbon Welded Gusset Support for Carbon
UG UA Steel and Stain. Stl. GSW1, GSW101 Steel and Stain. Stl. GSW1, GSW101 Steel and Stain. Stl. GSW1, GSW101 Steel and Stain. Stl. GSW1, GSW101
Pipe Size ½" - 2½" Sheet F25 Pipe Size ½" - 2½" Sheet F26 Pipe Size All Sizes Sheet F40 Pipe Size All Sizes Sheet F40 Pipe Size All Sizes Sheet F40 Pipe Size All Sizes Sheet F40

Bolted Gusset Support for Carbon Bolted Gusset Support for Carbon Bolted Gusset Support for Carbon Bolted Gusset Support for Carbon Bolted Gusset Support for Carbon Gusset Support for SP Item No.'s
Steel and Stain. Stl. GSB1, GSB101 Steel and Stain. Stl. GSB1, GSB101 Steel and Stain. Stl. GSB1, GSB101 Steel and Stain. Stl. GSB1, GSB101 Steel and Stain. Stl. GSB1, GSB101 SP-1914 & SP1916. GSW2
Pipe Size All Sizes Sheet F41 Pipe Size All Sizes Sheet F41 Pipe Size All Sizes Sheet F41 Pipe Size All Sizes Sheet F41 Pipe Size All Sizes Sheet F41 Pipe Size All Sizes Sheet F49

Lifting Lugs for Piping Break-Out Lifting Lugs for Piping Break-Out U-Bolt Guide for Pipes in the U-Bolt Anchor for Pipes in the Base Guide for Pipes in Base Anchor for Pipes in
Spools from an Elbow. LL102 Spools from Stain. Stl. Pipe. LL102 Caustic Sump. UG301 Caustic Sump. UA301 Caustic Sump. SB301 Caustic Sump. SB302
Pipe Sizes All Sizes. Sheet F44 Pipe Sizes All Sizes. Sheet F44 Pipe Size ½ - 2" Sheet F45 Pipe Size ½ - 2" Sheet F46 Pipe Size ¾" Sheet F47 Pipe Size ¾" Sheet F47

ATTACHMENT F - PIPE SUPPORT SELECTION CHART ('U' BOLT GUIDE/ANCHOR, SHEAR LUG) SHEET No. J11B
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 1

Pipe Support Foundation for Pipe Support Foundation for Pipe Support Foundation from Pipe Support Foundation from
New Paving. F8N-1 New Paving. F8N-2 Existing Civil Plinth (Trunnion). F8N-3 Existing Civil Plinth (post). F8N-4
Pipe Size-All Sizes. Sheet G1 & G3 Pipe Size-All Sizes. Sheet G2 & G3 Pipe Size-All Sizes. Sheet G12 Pipe Size-All Sizes. Sheet G13

Pipe Support Foundation for posts Pipe Support Foundation for posts Pipe Support Foundation for trunnions Pipe Support Foundation for trunnions
Unpaved Areas, Light Loads. F9-1 Unpaved Areas, Heavy Loads. F9-2 Unpaved Areas, Light Loads. F9-4 Unpaved Areas, Light Loads. F9-4
Pipe Size-All Sizes. Sheet G4,G5 Pipe Size-All Sizes. Sheet G6,G7 Pipe Size-All Sizes. Sheet G8,G9 Pipe Size-All Sizes. Sheet G10,G11

Pipe Support foundation for non Pipe Support foundation for non Pipe Support foundation for non
paved areas for 2" & 3" trunnions and Pipe Support foundation for non paved Pipe Support foundation for non paved paved areas for welded posts paved areas for Small Bore Pipe
welded posts HEA 100 areas for 4" & 6" trunnions areas for 8",10' & 12" trunnions HEA160 & HEA200 Supports and 70 x 8 Angle Posts
F9-6 F9-7 F9-8 F9-9 F9-10
Pipe Size-All Sizes. Sheet G14 Pipe Size-All Sizes. Sheet G15 Pipe Size-All Sizes. Sheet G16 Pipe Size-All Sizes. Sheet G17 Pipe Size-1/2" -2". Sheet G18

ATTACHMENT G - PIPE SUPPORT SELECTION CHART (FOUNDATION TYPES) SHEET No. J12
TENGIZCHEVROIL ASSET DEVELOPMENT PROJECTS PFD
CONTRACT No 571500
SPECIFICATION FOR PIPE SUPPORTS DOC No 60-0000-L-SPE-0002
Rev. 1

Cold Shoe - Standard Length Cold Shoe - Long. Cold Double Shoe - Std. Length Cold Anchor Shoe - 600 Lg. Cold Anchor Shoe - 800 Lg. Directional Anchor for Cold Insulated
CS1. CS2. CS3 CAS1. CAS1. Pipe. CDA1
Pipe Size ¾"-24". Sheet H1 Pipe Size 4"-24". Sheet H2 Pipe Size 8" 24". Sheet H3 Pipe Size ¾" - 10". Sheet H4 Pipe Size 12" - 24". Sheet H4 Pipe Size ¾" - 3". Sheet H5

Directional Anchor for Cold Insulated Non-Adjustable Hanger for Cold Base Support for Cold Trunnion Support for Cold 4-Directional Vertical Guide for Cold 2-Directional Vertical Guide for Cold
Pipe. CDA1 Insulated Pipe. CH2 Insulated Pipe. CBS1 Insulated Pipe. CTS1 Insulated Pipes. CVG1,CVG2,CVG3. Insulated Pipes. CVG4,CVG5,CVG6.
Pipe Size 4" - 24". Sheet H5 Pipe Size ¾" - 24". Sheet H6 & H7 Trunnion Size 2" - 16". Sheet H8 Pipe Size 2" - 24". Sheet H9 Pipe Size 8" - 24". Sheet H10 & H11 Pipe Size 8" - 24". Sheet H12 & H13

Hold Down for Uninsulated Pipe. Hold Down for Uninsulated Pipe. Hold Down Guide for Uninsulated Hold Down for Insulated Pipe Slotted Hold Down for Uninsulated Slotted Hold Down for Uninsulated
HD1. HD1. Pipe. HD2. HD3. Pipe. HDS1. Pipe. HDS2.
Pipe Size ¾" - 11/2". Sheet H14 Pipe Size 2" - 12". Sheet H15 & H16 Pipe Size 2" - 12" Sheet H17 & Pipe Size 1" - 12" Sheet H19 & H20 Pipe Size 2" - 12". Sheet H21 & H22 Pipe Size 2" - 12" Sheet H23 &
H18 H24

Anchor Strap for Uninsulated


Galvanised Pipe. AS1.
Pipe Size 1½" - 8" Sheet H25 & H26

ATTACHMENT H - PIPE SUPPORT SELECTION CHART (COLD SHOES, GUIDES, LINE STOPS, HANGERS, TRUNNIONS) SHEET No. J13

You might also like