Professional Documents
Culture Documents
APM Support
T his AMI BIOS supports Version 1.1&1.2 of the Advanced Power Management
(APM) speci fication. Power management features are implemented via the System
Management Int errupt (SMI). Sleep and Suspend power man agement modes are
supported. Power to the hard disk drives and video monitors can also be managed by
this AMI BIOS.
ACPI Support
AMI ACPI BIOS support Version 1.0/2.0 of Advanced Configuration and Power
interface specifi cation (ACPI). It provides ASL code for pow er manag ement and
device con figuration capabilities as defined in the ACPI specification, developed by
Microso ft, Intel and T oshiba.
DRAM S upport
DDR2 SDRAM (Double Data Rate II Synchronous DRAM) is supported.
Supported CP Us
T his AMI BIOS supports the Intel CPU.
Using Setup
When starting up the computer, press
<Del> during the Power-On Self-Test
(POST) to enter the BIOS setup utility.
In the BIOS setup utility, you will see
General Help description at the top right
corner, and this is providing a brief
description of the selected item.
Navigation Keys for that particular menu
are at the bottom right corner, and you can
use these keys to select item and ch ange
the settings.
General Help
Navigation Keys
Notice
z
z
z
T he default BIOS settings apply for most conditions to ensure optimum performan ce
of the motherboard. If the system becomes unstable after changing any settings,
please load the default settings to ensure systems compatibility and stability. Use
Load Setup Default under the Exit Menu.
For better system perform ance, the BIOS firmware is being continuously updated.
T he BIOS information described in this manual is for your reference only. The actual
BIOS information and settings on board may be slightly different from this manual.
T he content of this manual is subject to be chang ed without notice. We will not be
responsible for any mistakes found in this users manual and any system damage that
may be caused by wrong-settings.
Advan ced
PCIPnP
System Overvie w
AMI BIOS
Version
:01. 01.01
Build Date:01/ 01/08
System Time
System Date
Exit
Floppy A
> IDE Configur ation
+Tab
F1
F10
ESC
S elect Screen
S elect Item
C hange Field
S elect Field
G eneral Help
S ave and Exit
E xit
AMI BIOS
Shows system information including BIOS version, built date, etc.
System Time
Set the system internal clock.
System Date
Set the system date. Note that the Day automatically changes when you set the
date.
Floppy A
Select the type of floppy disk drive installed in your system.
Options: 360K, 5.25 in / 1.2M, 5.25 in / 720K, 3.5 in / 1.44M, 3.5 in /
2.88M, 3.5 in / None
Options
Disabled
Compatible
Enhanced
[Dis abled]
[35]
S elect Screen
S elect Item
EnterG o to Sub Screen
F1
G eneral Help
F10 S ave and Exit
ESC E xit
ATA/IDE Configuration
T his item allows you to control the onboard IDE controller.
Options: Enhanced (Default) / Compatible / Disabled
Configure SATA Channels
T his item allows you to control the SAT A channel configuration sequence..
Options: Befo re PATA (Default) / Behind PAT A
Type
[Auto]
LBA/Large Mode
[Auto]
Block (Multi-Sector Transfer)[Auto]
PIO Mode
[Auto]
DMA Mode
[Auto]
S.M.A.R.T
[Auto]
32Bit Data Transfer
[Enabled]
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
T he BIOS detects the information and values of resp ective devices, and these
information and values are shown below to the name of the sub-menu.
Type
Select the type of the IDE/SAT A drive.
Options: Auto (Default) / CDROM / ARMD / Not Installed
LBA/Large Mode
Enable or disable the LBA mode.
Options: Auto (Default) / Disabled
Block (Multi-Sector Transfer)
Enable or disable multi-sector trans fer.
Options: Auto (Default) / Disabled
PIO Mode
Select the PIO mode.
Options: Auto (Default) / 0 / 1 / 2 / 3 / 4
DMA Mode
Select the DMA mode.
Options: Auto (Default) / Disabled
Notice
z
Beware of that setting inappropriate values in items of this menu may cause
system to malfunction.
Main
Advan ced
PCIPnP
Exit
Configure CPU.
CPU Configuration
T his item shows the CPU information that the BIOS automatically detects.
BIOS SETU P U TILITY
Advan ced
Configure adva nced CPU settings
Module Version :xx.xx
Manufacturer:I ntel
Frequency
:
FSB Speed
:
Cache L1
:
Cache L2
:
Ratio Actual V alue:
Hardware Prefe tcher
[En abled]
Adjacent Cache Line Prefetch [En abled]
Max CPUID Valu e Limit
[Di sabled]
Intel(R) Virtu alization Tech [En abled]
Execute-Disabl e Bit Capability[En abled]
PECI
[Di sabled]
Core Multi-Pro cessing
[En abled]
Intel(R) Speed Step(tm) tech
[En abled]
+F1
F10
ESC
S elect Screen
S elect Item
C hange Option
G eneral Help
S ave and Exit
E xit
SuperIO Configuration
BIOS SETU P U TILITY
Advan ced
Configure ITE8 712 Super IO Chipse t
Onboard Floppy Controller
Serial Port1 A ddress
Parallel Port Address
Parallel Por t Mode
Parallel Por t IRQ
Keyboard Power On
Mouse PowerOn
Restore on AC Power Loss
[Ena bled]
[3F8 /IRQ4]
[378 ]
[Nor mal]
[IRQ 7]
[Dis abled]
[Dis abled]
[Pow er Off]
+F1
F10
ESC
S elect Screen
S elect Item
C hange Option
G eneral Help
S ave and Exit
E xit
10
Enables Hardware
Health Monitoring
Device.
CPU Temperatur e
CPU FAN Speed
SYS FAN Speed
CPU Vcore
Chipset Voltag e
+3.30V
+5.00V
+12.0V
FSB Voltage
Memory Voltage
5V(SB)
Voltage Batter y
+F1
F10
ESC
S elect Screen
S elect Item
C hange Option
G eneral Help
S ave and Exit
E xit
11
[Dis abled]
+F1
F10
ESC
S elect Screen
S elect Item
C hange Option
G eneral Help
S ave and Exit
E xit
12
Power Configuration
BIOS SETU P U TILITY
Advan ced
ACPI Settings
Suspend mode
Repost Video o n S3 Resume
ACPI Version F eatures
ACPI APIC supp ort
AMI OEMB table
Headless mode
Energy Lake Fe ature
APIC ACPI SCI IRQ
USB Device Wak eup From S3/S4
High Performan ce Event Timer
[S1( POS)]
[NO]
[ACP I v1.0]
[Ena bled]
[Ena bled]
[Dis abled]
[Dis abled]
[Dis abled]
[Dis abled]
[Dis abled]
+F1
F10
ESC
S elect Screen
S elect Item
C hange Option
G eneral Help
S ave and Exit
E xit
Suspend mode
T he item allows you to select the suspend type under the ACPI operating system.
Options: S1 (POS) (Default)
Power on Suspend
S3 (ST R)
Suspend to RAM
Auto
POS+STR
Repost Video on S3 Resume
Options:
NO (Default) / YES
13
14
15
[Ena bled]
[HiS peed]
[Ena bled]
S elect Screen
S elect Item
C hange Option
G eneral Help
S ave and Exit
E xit
16
Number of seconds
POST waits for the
USB mass storage
device after start
unit command.
[Auto]
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
17
Notice
z
Beware of that setting inappropriate values in items of this menu may cause
system to malfunction.
Main
Advan ced
PCIPnP
Exit
[No]
[No]
[64]
[Yes ]
[Dis abled]
[Ena bled]
+F1
F10
ESC
S elect Screen
S elect Item
C hange Option
G eneral Help
S ave and Exit
E xit
Clear NV RAM
T his item allows you to clear the data in the NVRAM (CMOS) by selecting Yes.
Options: No (Default) / Yes
18
Palette Snooping
Some old graphic controllers need to snoop on the VGA palette and then map it to
their display as a way to provide boot information and VGA compatibility. This item
allows such snooping to take place.
Options: Disabled (Default) / Enabled
PCI Resource
BIOS SETU P U TILITY
PCIPnP
PCI Resource
IRQ3
IRQ4
IRQ5
IRQ7
IRQ9
IRQ10
IRQ11
IRQ14
IRQ15
DMA
DMA
DMA
DMA
DMA
DMA
[Ava ilable]
[Ava ilable]
[Ava ilable]
[Ava ilable]
[Ava ilable]
[Ava ilable]
[Ava ilable]
[Ava ilable]
[Ava ilable]
Channel
Channel
Channel
Channel
Channel
Channel
0
1
3
5
6
7
[Ava ilable]
[Ava ilable]
[Ava ilable]
[Ava ilable]
[Available]
[Ava ilable]
Available: Specified
IRQ is available to be
used by PCI/PnP
devices.
Reserved: Specified
IRQ is reserved for
use by Legacy ISA
devices.
+F1
F10
ESC
S elect Screen
S elect Item
C hange Option
G eneral Help
S ave and Exit
E xit
[Dis abled]
19
Enable/Disable
PCI Express L0s and
L1 link power
states.
+F1
F10
ESC
S elect Screen
S elect Item
C hange Option
G eneral Help
S ave and Exit
E xit
20
Port
Port
Port
Port
Port
Port
0
1
2
3
4
5
IOxAPIC
IOxAPIC
IOxAPIC
IOxAPIC
IOxAPIC
IOxAPIC
Enable
Enable
Enable
Enable
Enable
Enable
Options
[Aut o]
[Aut o]
[Aut o]
[Aut o]
[Aut o]
[Aut o]
[Dis abled]
[Dis abled]
[Dis abled]
[Dis abled]
[Dis abled]
[Dis abled]
[Dis abled]
Auto
Enabled
Disabled
+F1
F10
ESC
S elect Screen
S elect Item
C hange Option
G eneral Help
S ave and Exit
E xit
21
Advan ced
PCIPnP
Boot Settings
>
>
>
>
Exit
Specifies the
Boot Device
Priority sequence.
Removable Drives
T he BIOS will attempt to arrange the removable drive boot sequence automatically.
You can also change the booting sequence. The number of device items that
appears on the screen depends on the number of devices installed in the system.
22
[Ena bled]
[Ena bled]
[For ce BIOS]
[ON]
+F1
F10
ESC
S elect Screen
S elect Item
C hange Option
G eneral Help
S ave and Exit
E xit
Quick Boot
Enabling this option will cause an ab ridged version o f the Power On Sel f-T est
(POST ) to execute after you power up the computer.
Options: Enabled (Default) / Disabled
Full Screen LOGO Show
T his item allows you to enable/disable Full Screen LOGO Show function.
Options: Enabled (Default) / Disabled
AddOn ROM Display Mode
T his item sets the display mode for option ROM.
Options: Force BIOS (Default) / Keep Current
23
24
Notice
z
Beware of that setting inappropriate values in items of this menu may cause
system to malfunction.
Main
Advan ced
PCIPnP
Exit
S elect Screen
S elect Item
EnterG o to Sub Screen
F1
G eneral Help
F10 S ave and Exit
ESC E xit
vxx .xx (C)Copyright 1985-200x, American Me gatrends, Inc.
25
[E nabled]
[D isabled]
ENABLE: Allow
remapping of
overlapped PCI memory
above the total
physical memory.
[P EG/PCI]
[E nabled,8MB]
[A uto]
+F1
F10
ESC
S elect Screen
S elect Item
C hange Option
G eneral Help
S ave and Exit
E xit
26
Options
USB Functions
USB 2.0 Contro ller
Audio Controll er
[8 USB Ports]
[E nabled]
[A zalia]
[E nabled]
[D isabled]
SMBUS Controll er
[E nabled]
[1 to 2 seconds]
Disabled
2 USB Ports
4 USB Ports
6 USB Ports
8 USB Ports
+F1
F10
ESC
S elect Screen
S elect Item
C hange Option
G eneral Help
S ave and Exit
E xit
USB Functions
T he item determines the number of functional USB port.
Options: 8 USB Ports (Default) / 6 USB Ports / 4 USB Ports / 2 USB Ports /
Disabled
USB 2.0 Controller
T his entry is to enabled/ disabled EHCI controller only. T his Bios itself may/may not
have high speed USB support. If the Bios has high speed USB support built in,the
support will be automately turn on when high speed device were attached.
Options: Enabled (Default) / Disabled
Audio Controller
T his item allows you to select the Audio support.
Options: Azalia (D efault) / Disabled
27
1 to 2 seconds (Default)
28
Notice
z
Beware of that setting inappropriate values in items of this menu may cause
system to malfunction.
Main
Advan ced
PCIPnP
[3 33]
[A uto]
[1 00]
CPU Voltage
[D efault]
DRAM Frequency
Configure DRAM Timing by SPD
DRAM CAS# La tency
DRAM RAS# to CAS# Delay
DRAM RAS# Pr echarge
DRAM RAS# Ac tivate to Precha
[A uto]
[E nabled]
[5 ]
[6 DRAM Clocks]
[6 DRAM Clocks]
[1 5 DRAM Clocks]
Exit
S elect Screen
S elect Item
EnterG o to Sub Screen
F1
G eneral Help
F10 S ave and Exit
ESC E xit
PCIE Clock By
T his item allows you to select the PCIE clock control
Options: Auto (Default) / Fixed 100 / Manual
29
DRAM Frequency
T his item allows you to control the Memory Clock.
Options: Auto (Default) / DDR2 533Mhz / DDR2 667Mhz / DDR2 800Mhz
5 (Default)
30
Advan ced
PCIPnP
Exit Options
Exit
> Security
S elect Screen
S elect Item
EnterG o to Sub Screen
F1
G eneral Help
F10 S ave and Exit
ESC E xit
vxx .xx (C)Copyright 1985-200x, American Me gatrends, Inc.
Discard Changes
Abandon all changes made during the current session and restore the previously
saved values.
31
[Ful l Access]
[Set up]
S elect Screen
S elect Item
EnterC hange
F1
G eneral Help
F10 S ave and Exit
ESC E xit
32
33