Professional Documents
Culture Documents
TMP35/TMP36/TMP37
GENERAL DESCRIPTION
The TMP35/TMP36/TMP37 are low voltage, precision centigrade temperature sensors. They provide a voltage output that
is linearly proportional to the Celsius (centigrade) temperature.
The TMP35/ TMP36/TMP37 do not require any external
calibration to provide typical accuracies of 1C at +25C
and 2C over the 40C to +125C temperature range.
The low output impedance of the TMP35/TMP36/TMP37 and
its linear output and precise calibration simplify interfacing to
temperature control circuitry and ADCs. All three devices are
intended for single-supply operation from 2.7 V to 5.5 V maximum. The supply current runs well below 50 A, providing
very low self-heatingless than 0.1C in still air. In addition, a
shutdown function is provided to cut the supply current to less
than 0.5 A.
The TMP35 is functionally compatible with the LM35/LM45
and provides a 250 mV output at 25C. The TMP35 reads
temperatures from 10C to 125C. The TMP36 is specified from
40C to +125C, provides a 750 mV output at 25C, and
operates to 125C from a single 2.7 V supply. The TMP36 is
functionally compatible with the LM50. Both the TMP35 and
TMP36 have an output scale factor of 10 mV/C.
TMP35/
TMP36/
TMP37
VOUT
00337-001
SHUTDOWN
Figure 1.
PIN CONFIGURATIONS
VOUT
+VS
NC
5 GND
TOP VIEW
(Not to Scale)
4 SHUTDOWN
NC = NO CONNECT
00337-002
APPLICATIONS
VOUT 1
7 NC
TOP VIEW
NC 3 (Not to Scale) 6 NC
NC 2
5 SHUTDOWN
GND 4
NC = NO CONNECT
00337-003
BOTTOM VIEW
(Not to Scale)
00337-004
FEATURES
Rev. F
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
TMP35/TMP36/TMP37
TABLE OF CONTENTS
Features .............................................................................................. 1
Applications....................................................................................... 1
Specifications..................................................................................... 3
ESD Caution.................................................................................. 4
Shutdown Operation.................................................................... 9
REVISION HISTORY
11/10Rev. E to Rev. F
10/02Rev. B to Rev. C
Changes to Features.......................................................................... 1
Updated Outline Dimensions ....................................................... 18
Changes to Ordering Guide .......................................................... 19
Added Automotive Products Section .......................................... 20
Changes to Specifications.................................................................3
Deleted Text from Commentary on Long-Term Stability
Section.............................................................................................. 13
Updated Outline Dimensions....................................................... 14
8/08Rev. D to Rev. E
9/01Rev. A to Rev. B
3/05Rev. C to Rev. D
Updated Format..................................................................Universal
Changes to Specifications ................................................................ 3
Additions to Absolute Maximum Ratings..................................... 4
Updated Outline Dimensions ....................................................... 18
Changes to Ordering Guide .......................................................... 19
6/97Rev. 0 to Rev. A
3/96Revision 0: Initial Version
Rev. F | Page 2 of 20
TMP35/TMP36/TMP37
SPECIFICATIONS
VS = 2.7 V to 5.5 V, 40C TA +125C, unless otherwise noted.
Table 1.
Parameter 1
ACCURACY
TMP35/TMP36/TMP37 (F Grade)
TMP35/TMP36/TMP37 (G Grade)
TMP35/TMP36/TMP37 (F Grade)
TMP35/TMP36/TMP37 (G Grade)
Scale Factor, TMP35
Scale Factor, TMP36
Scale Factor, TMP37
Symbol
Load Regulation
PSRR
Test Conditions/Comments
Min
TA = 25C
TA = 25C
Over rated temperature
Over rated temperature
10C TA 125C
40C TA +125C
5C TA 85C
5C TA 100C
3.0 V VS 5.5 V
0 A IL 50 A
40C TA +105C
105C TA +125C
TA = 25C
3.0 V VS 5.5 V
TA = 150C for 1 kHz
VIH
VIL
VS = 2.7 V
VS = 5.5 V
VS
ISY (ON)
ISY (OFF)
Max
Unit
1
1
2
2
10
10
20
20
2
3
3
4
C
C
C
C
mV/C
mV/C
mV/C
mV/C
6
25
30
50
0.5
0.4
20
60
100
mC/A
mC/A
mC/V
mC/V
C
C
1.8
400
TA = 25C
TA = 25C
TA = 25C
IL
ISC
CL
Typ
250
750
500
10000
0.5
mV
mV
mV
mV
A
A
pF
ms
0.01
5.5
50
0.5
V
A
A
100
0
Note 2
No oscillations 2
Output within 1C, 100 k||100 pF load2
1000
2000
50
250
2.7
Unloaded
Unloaded
Rev. F | Page 3 of 20
V
mV
TMP35/TMP36/TMP37
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter1, 2
Supply Voltage
Shutdown Pin
Output Pin
Operating Temperature Range
Die Junction Temperature
Storage Temperature Range
IR Reflow Soldering
Peak Temperature
Time at Peak Temperature Range
Ramp-Up Rate
Ramp-Down Rate
Time 25C to Peak Temperature
IR Reflow SolderingPb-Free Package
Peak Temperature
Time at Peak Temperature Range
Ramp-Up Rate
Ramp-Down Rate
Time 25C to Peak Temperature
Rating
7V
GND SHUTDOWN +VS
GND VOUT +VS
55C to +150C
175C
65C to +160C
220C (0C/5C)
10 sec to 20 sec
3C/sec
6C/sec
6 min
260C (0C)
20 sec to 40 sec
3C/sec
6C/sec
8 min
THERMAL RESISTANCE
JA is specified for the worst-case conditions, that is, a device in
socket.
Table 3. Thermal Resistance
Package Type
TO-92 (T-3)
SOIC_N (R-8)
SOT-23 (RJ-5)
ESD CAUTION
Rev. F | Page 4 of 20
JA
162
158
300
JC
120
43
180
Unit
C/W
C/W
C/W
TMP35/TMP36/TMP37
TYPICAL PERFORMANCE CHARACTERISTICS
0.4
30
20
10
50
TEMPERATURE (C)
100
0.3
0.2
0.1
0
50
150
1.4
b
1.2
1.0
0.8
0.6
00337-007
0.4
0.2
0
50
25
75
100
125
31.600
25
50
TEMPERATURE (C)
75
100
1.6
25
50
TEMPERATURE (C)
100.000
a. TMP35
b. TMP36
c. TMP37
+VS = 3V
1.8
2.0
25
10.000
3.160
1.000
0.320
0.100
0.032
00337-010
0
50
00337-009
40
00337-005
50
0.010
20
125
100
1k
FREQUENCY (Hz)
10k
100k
4
MINIMUM SUPPLY VOLTAGE (V)
1
0
1
b
2
3
4
5
c
0
20
40
60
80
100
TEMPERATURE (C)
120
NO LOAD
3
b
2
1
a. TMP35/TMP36
b. TMP37
0
50
140
25
25
50
TEMPERATURE (C)
00337-011
00337-008
75
100
Rev. F | Page 5 of 20
125
TMP35/TMP36/TMP37
60
400
a. +VS = 5V
b. +VS = 3V
300
NO LOAD
40
a
30
00337-012
10
50
25
25
50
TEMPERATURE (C)
75
200
= +VS AND SHUTDOWN PINS
LOW TO HIGH (0V TO 3V)
VOUT SETTLES WITHIN 1C
100
20
100
00337-015
50
0
50
125
25
25
50
TEMPERATURE (C)
75
100
125
400
50
= SHUTDOWN PIN
HIGH TO LOW (3V TO 0V)
TA = 25C, NO LOAD
300
30
20
200
100
= SHUTDOWN PIN
LOW TO HIGH (0V TO 3V)
VOUT SETTLES WITHIN 1C
00337-013
10
0
1
3
4
5
SUPPLY VOLTAGE (V)
0
50
75
100
125
0.8
a. +VS = 5V
b. +VS = 3V
TA = 25C
+VS = 3V
SHUTDOWN =
SIGNAL
0.6
OUTPUT VOLTAGE (V)
NO LOAD
30
20
a
10
0.4
0.2
0
1.0
0.8
0.6
TA = 25C
+VS AND SHUTDOWN =
SIGNAL
0.4
00337-014
25
50
TEMPERATURE (C)
1.0
50
b
0
50
Figure 15. VOUT Response Time for SHUTDOWN Pin vs. Temperature
40
25
25
25
50
TEMPERATURE (C)
75
100
0.2
0
125
00337-017
00337-016
40
50
50
100
300
350
400
450
Figure 16. VOUT Response Time to SHUTDOWN Pin and +VS Pin vs. Time
Rev. F | Page 6 of 20
TMP35/TMP36/TMP37
110
10mV
100
90
90
VOLT/DIVISION
70
60
50
40
20
10
0%
10
0
00337-019
30
100
200
300
TIME (s)
400
500
TIME/DIVISION
600
140
2400
2200
120
100
80
+VS = 3V, 5V
60
b
40
c
00337-018
20
a
0
100
200
300
400
500
AIR VELOCITY (FPM)
600
70
60
50
40
30
20
00337-035
CHANGE (%)
+VS = 3V, 5V
10
0
10
20
30
TIME (s)
40
50
1400
1200
1000
800
600
400
a. TMP35/TMP36
b. TMP37
10
100
1k
FREQUENCY (Hz)
80
1600
700
100
90
1800
200
110
2000
60
Rev. F | Page 7 of 20
00337-020
CHANGE (%)
100
+VS = 3V, 5V
80
1ms
10k
TMP35/TMP36/TMP37
FUNCTIONAL DESCRIPTION
An equivalent circuit for the TMP3x family of micropower,
centigrade temperature sensors is shown in Figure 22. The core
of the temperature sensor is a band gap core that comprises
transistors Q1 and Q2, biased by Q3 to approximately 8 A. The
band gap core operates both Q1 and Q2 at the same collector
current level; however, because the emitter area of Q1 is 10
times that of Q2, the VBE of Q1 and the VBE of Q2 are not equal
by the following relationship:
SHUTDOWN
25A
3X
Q2
1X
Q4
AE,Q1
= VT ln
AE,Q2
2X
R1
Q1
10X
R3
R2
VOUT
7.5A
Q3
2X
6X
GND
00337-006
VBE
+VS
Rev. F | Page 8 of 20
Offset
Voltage (V)
0
0.5
0
Output Voltage
Scaling (mV/C)
10
10
20
Output Voltage
@ 25C (mV)
250
750
500
TMP35/TMP36/TMP37
APPLICATIONS INFORMATION
SHUTDOWN OPERATION
MOUNTING CONSIDERATIONS
If the TMP3x temperature sensors are thermally attached and
protected, they can be used in any temperature measurement
application where the maximum temperature range of the
medium is between 40C and +125C. Properly cemented or
glued to the surface of the medium, these sensors are within
0.01C of the surface temperature. Caution should be exercised,
especially with T-3 packages, because the leads and any wiring
to the device can act as heat pipes, introducing errors if the
surrounding air-surface interface is not isothermal. Avoiding this
condition is easily achieved by dabbing the leads of the temperature sensor and the hookup wires with a bead of thermally
conductive epoxy. This ensures that the TMP3x die temperature
is not affected by the surrounding air temperature. Because
plastic IC packaging technology is used, excessive mechanical
stress should be avoided when fastening the device with a clamp
or a screw-on heat tab. Thermally conductive epoxy or glue,
which must be electrically nonconductive, is recommended
under typical mounting conditions.
These temperature sensors, as well as any associated circuitry,
should be kept insulated and dry to avoid leakage and corrosion.
In wet or corrosive environments, any electrically isolated metal
or ceramic well can be used to shield the temperature sensors.
Condensation at very cold temperatures can cause errors and
should be avoided by sealing the device, using electrically nonconductive epoxy paints or dip or any one of the many printed
circuit board coatings and varnishes.
TJ
CCH
TC
CC
CA
TA
00337-021
PD
JC
Rev. F | Page 9 of 20
TMP35/TMP36/TMP37
BASIC TEMPERATURE SENSOR CONNECTIONS
FAHRENHEIT THERMOMETERS
+VS
VOUT
GND
R1
(TMP35 ) + R3 ( AD589 )
VOUT =
R1 + R2
R3 + R4
+VS
GND
VOUT
SHUTDOWN
SOIC_N
SOT-23
TO-92
2
1
5
3
1
2
4
NA
PACKAGE
00337-022
PIN ASSIGNMENTS
where:
TMP35 is the output voltage of the TMP35 or the TMP37 at the
measurement temperature, TM.
AD589 is the output voltage of the reference, that is, 1.23 V.
The output voltage of this circuit is not referenced to the
circuits common ground. If this output voltage were applied
directly to the input of an ADC, the ADC common ground
should be adjusted accordingly.
+VS
0.1F
+VS
TMP35/
TMP37
VOUT
R1
GND
+
R2
VOUT
AD589
1.23V
R3
R4
SENSOR
TMP35
TMP37
1mV/F
2mV/F
45.3
45.3
10
10
10
10
374
182
Rev. F | Page 10 of 20
00337-023
TMP3x
SHUTDOWN
TMP35/TMP36/TMP37
At the expense of additional circuitry, the offset produced by
the circuit in Figure 26 can be avoided by using the circuit in
Figure 27. In this circuit, the output of the TMP36 is conditioned
by a single-supply, micropower op amp, the OP193. Although
the entire circuit operates from a single 3 V supply, the output
voltage of the circuit reads the temperature directly, with a
transfer characteristic of 1 mV/F, without offset. This is accomplished through an ADM660, which is a supply voltage inverter.
The 3 V supply is inverted and applied to the V terminal of the
OP193. Thus, for a temperature range between 40F and +257F,
the output of the circuit reads 40 mV to +257 mV. A general
expression for the transfer equation of the circuit is given by
R6
1 + R4 (TMP36 ) R4 VS
VOUT =
R5 + R6
R3
R3 2
R1
45.3k
GND
R2
10k
00337-024
TMP36
0.1F
R1
50k
R3
R4
C1 +
10F
R2
50k
0.1F
7
2
+VS
VOUT
TMP36
R5
VOUT @ 1mV/F
40F TA +257F
R6
GND
OP193
NC
ELEMENT
VALUE
R3
258.6k
R4
10k
R5
47.7k
R6
10k
2
10F
ADM660
3V
+
10F
4
3
NC
00337-025
10F/0.1F
Rev. F | Page 11 of 20
TMP35/TMP36/TMP37
2.7V < +VS < 5.5V
0.1F
2
3
TMP3x
TMP3x
VTEMP(AVG)
@ 10mV/C FOR TMP35/TMP36
@ 20mV/C FOR TMP37
OP193
+
R5
100k
R1
300k
R6
7.5k
R2
300k
FOR R1 = R2 = R3 = R;
TMP3x
R3
300k
R4
7.5k
0.1F
TMP36
@ T1
R11
R21
R8
25k
0.1F
7
2
0.1F
TMP36
R31
OP193
3
@ T2
VOUT
4
R7
100k
R9
25k
CENTERED AT
0C TA 125C
R5
100k
1F
R6
100k
VOUT = T2 T1 @ 10mV/C
VS
CENTERED AT
2
NOTE:
1 R1R4, CADDOCK T914100k100, OR EQUIVALENT.
Rev. F | Page 12 of 20
00337-027
R41
TMP35/TMP36/TMP37
Because temperature is a slowly moving quantity, the possibility
for comparator chatter exists. To avoid this condition, hysteresis
is used around the comparator. In this application, a hysteresis
of 5C about the trip point was arbitrarily chosen; the ultimate
value for hysteresis should be determined by the end application.
The output logic voltage swing of the comparator with R1 and
R2 determines the amount of comparator hysteresis. Using a
3.3 V supply, the output logic voltage swing of the CMP402 is
2.6 V; therefore, for a hysteresis of 5C (50 mV @ 10 mV/C),
R1 is set to 20 k, and R2 is set to 1 M. An expression for the
hysteresis of this circuit is given by
R1
VHYS =
VLOGIC SWING, CMP402
R2
3.3V
R2
1M
+VS
TMP35
VOUT
CL
1000pF
R5
100k
GND
R1B
10k
CMP402
+
INTERRUPT
14
0.1F
13
REF191
R3
16k
6
+
1F
>80C
<80C
VREF
R4
10k
0.1F
C1 = 1 CMP402
4
Rev. F | Page 13 of 20
00337-028
0.1F
0.1F
R1A
10k
TMP35/TMP36/TMP37
and the wires of the thermocouple from introducing an error in
the measured temperature. This compensation works extremely
well for circuit ambient temperatures in the range of 20C to 50C.
Over a 250C measurement temperature range, the thermocouple
produces an output voltage change of 10.151 mV. Because the
required output full-scale voltage of the circuit is 2.5 V, the gain
of the circuit is set to 246.3. Choosing R4 equal to 4.99 k sets
R5 equal to 1.22 M. Because the closest 1% value for R5 is
1.21 M, a 50 k potentiometer is used with R5 for fine trim of
the full-scale output voltage. Although the OP193 is a superior
single-supply, micropower operational amplifier, its output stage
is not rail-to-rail; therefore, the 0C output voltage level is 0.1 V.
If this circuit is digitized by a single-supply ADC, the ADC
common should be adjusted to 0.1 V accordingly.
+VS
TMP35
R11
24.9k
COLD
JUNCTION
ALUMEL
0C TA 250C
ISOTHERMAL
BLOCK
R51
1.21M
7
2
OP193
CU
+
TYPE K
THERMOCOUPLE
R4
4.99k
0.1F
GND
CHROMEL
P1
50k
CU
R6
100k
5%
VOUT
0V TO 2.5V
NOTE:
1 ALL RESISTORS 1% UNLESS OTHERWISE NOTED.
R21
102
Figure 31. Single-Supply, Type K Thermocouple Signal Conditioning Circuit with Cold-Junction Compensation
Rev. F | Page 14 of 20
00337-029
0.1F
R3
10M
5%
VOUT
TMP35/TMP36/TMP37
USING TMP3x SENSORS IN REMOTE LOCATIONS
R1
4.7k
5V
2N2907
VOUT
+VS
0.1F
0.01F
TMP3x
GND
VOUT
R3
R2
SENSOR R2
R3
TMP35
634
634
TMP36
887
887
TMP37
1k
1k
00337-030
TWISTED PAIR
BELDEN TYPE 9502
OR EQUIVALENT
Figure 33 illustrates a circuit that transmits temperature information in this fashion. Using a TMP3x as the temperature sensor,
the output current is linearly proportional to the temperature of
the medium. The entire circuit operates from the 3 V output of
the REF193. The REF193 requires no external trimming because
of its tight initial output voltage tolerance and the low supply
current of the TMP3x, the OP193, and the REF193. The entire
circuit consumes less than 3 mA from a total budget of 4 mA.
The OP193 regulates the output current to satisfy the current
summation at the noninverting node of the OP193. A generalized
expression for the KCL equation at Pin 3 of the OP193 is given by
1 TMP3x R3 VREF R3
I OUT =
+
R1
R2
R7
For each temperature sensor, Table 5 provides the values for the
components P1, P2, and R1 to R4.
Table 5. Circuit Element Values for Loop Transmitter
Sensor
TMP35
TMP36
TMP37
R1
97.6 k
97.6 k
97.6 k
P1
5 k
5 k
5 k
R2
1.58 M
931 k
10.5 k
P2
100 k
50 k
500
R3
140 k
97.6 k
84.5 k
R4
56.2 k
47 k
8.45 k
Rev. F | Page 15 of 20
TMP35/TMP36/TMP37
3V
R21
P21
4mA
ADJUST
R11
TMP3x
VOUT
GND
1F
VLOOP
9V TO 18V
0.1F
2
P11
20mA
ADJUST
REF193
OP193
R6
100k
Q1
2N1711
VOUT
4
D1
R31
NOTE:
1 SEE TEXT FOR VALUES.
R5
100k
R41
RL
250
R7
100
D1: HP5082-2810
00337-032
+VS
IL
TEMPERATURE-TO-FREQUENCY CONVERTER
5V
RPU
5k
+VS
8
10F/0.1F
CT1
0.1F
VOUT
TMP3x
AD654
GND
RT1
5V
P2
100k
R1
ROFF1
470
fOUT
OFFSET
NOTE:
1R AND C SEE TABLE
T
T
ROFF2
10
SENSOR
RT (R1 + P1)
CT
TMP35
TMP36
TMP37
11.8k + 500
16.2k + 500
18.2k + 1k
1.7nF
1.8nF
2.1nF
Rev. F | Page 16 of 20
fOUT
00337-031
TMP35/TMP36/TMP37
An offset trim network (fOUT OFFSET ) is included with this
circuit to set fOUT to 0 Hz when the minimum output voltage of
the temperature sensor is reached. Potentiometer P1 is required
to calibrate the absolute accuracy of the AD654. The table in
Figure 34 illustrates the circuit element values for each of the
three sensors. The nominal offset voltage required for 0 Hz
output from the TMP35 is 50 mV; for the TMP36 and TMP37,
the offset voltage required is 100 mV. For the circuit values
shown, the output frequency transfer characteristic of the
circuit was set at 50 Hz/C in all cases. At the receiving end, a
frequency-to-voltage converter (FVC) can be used to convert
the frequency back to a dc voltage for further processing. One
such FVC is the AD650.
For complete information about the AD650 and the AD654,
consult the individual data sheets for those devices.
TMP3x
VOUT 750
LONG CABLE OR
HEAVY CAPACITIVE
LOADS
GND
00337-033
0.1F
Rev. F | Page 17 of 20
TMP35/TMP36/TMP37
OUTLINE DIMENSIONS
5.00 (0.1968)
4.80 (0.1890)
5
4
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0040)
COPLANARITY
0.10
SEATING
PLANE
6.20 (0.2441)
5.80 (0.2284)
1.75 (0.0688)
1.35 (0.0532)
0.51 (0.0201)
0.31 (0.0122)
1.70
1.60
1.50
0.50 (0.0196)
0.25 (0.0099)
3.00
2.80
2.60
45
8
0
0.95 BSC
0.25 (0.0098)
0.17 (0.0067)
1.90
BSC
1.27 (0.0500)
0.40 (0.0157)
1.30
1.15
0.90
1.45 MAX
0.95 MIN
0.15 MAX
0.05 MIN
0.50 MAX
0.35 MIN
0.20 MAX
0.08 MIN
10
5
0
SEATING
PLANE
0.60
BSC
0.210 (5.33)
0.190 (4.83)
0.170 (4.32)
0.0220 (0.56)
0.0185 (0.47)
0.0150 (0.38)
0.205 (5.21)
0.190 (4.83)
0.175 (4.45)
0.165 (4.19)
0.145 (3.68)
0.125 (3.18)
0.1150 (2.92)
0.0975 (2.48)
0.0800 (2.03)
0.055 (1.40)
0.050 (1.27)
0.045 (1.15)
3
2
1
0.020 (0.51)
0.017 (0.43)
0.014 (0.36)
BOTTOM VIEW
Rev. F | Page 18 of 20
042208-A
FRONT VIEW
0.105 (2.68)
0.100 (2.54)
0.095 (2.42)
0.55
0.45
0.35
11-01-2010-A
8
1
012407-A
4.00 (0.1574)
3.80 (0.1497)
3.00
2.90
2.80
TMP35/TMP36/TMP37
ORDERING GUIDE
Model1, 2
TMP35FSZ-REEL
TMP35GRT-REEL7
TMP35GRTZ-REEL7
TMP35GS
TMP35GT9
TMP35GT9Z
ADW75001Z-0REEL7
TMP36FS
TMP36FS-REEL
TMP36FSZ
TMP36FSZ-REEL
TMP36GRT-REEL7
TMP36GRTZ-REEL7
TMP36GS
TMP36GS-REEL
TMP36GS-REEL7
TMP36GSZ
TMP36GSZ-REEL
TMP36GSZ-REEL7
TMP36GT9
TMP36GT9Z
TMP37FT9
TMP37FT9-REEL
TMP37FT9Z
TMP37GRT-REEL7
TMP37GRTZ-REEL7
TMP37GSZ
TMP37GSZ-REEL
TMP37GT9
TMP37GT9-REEL
TMP37GT9Z
1
2
Accuracy at
25C (C max)
2.0
3.0
3.0
3.0
3.0
3.0
3.0
2.0
2.0
2.0
2.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
2.0
2.0
2.0
3.0
3.0
3.0
3.0
3.0
3.0
3.0
Linear Operating
Temperature Range
10C to 125C
10C to 125C
10C to 125C
10C to 125C
10C to 125C
10C to 125C
40C to +125C
40C to +125C
40C to +125C
40C to +125C
40C to +125C
40C to +125C
40C to +125C
40C to +125C
40C to +125C
40C to +125C
40C to +125C
40C to +125C
40C to +125C
40C to +125C
40C to +125C
5C to 100C
5C to 100C
5C to 100C
5C to 100C
5C to 100C
5C to 100C
5C to 100C
5C to 100C
5C to 100C
5C to 100C
Package Description
8-Lead Standard Small Outline Package (SOIC_N)
5-Lead Small Outline Transistor Package (SOT-23)
5-Lead Small Outline Transistor Package (SOT-23)
8-Lead Standard Small Outline Package (SOIC_N)
3-Pin Plastic Header-Style Package (TO-92)
3-Pin Plastic Header-Style Package (TO-92)
5-Lead Small Outline Transistor Package (SOT-23)
8-Lead Standard Small Outline Package (SOIC_N)
8-Lead Standard Small Outline Package (SOIC_N)
8-Lead Standard Small Outline Package (SOIC_N)
8-Lead Standard Small Outline Package (SOIC_N)
5-Lead Small Outline Transistor Package (SOT-23)
5-Lead Small Outline Transistor Package (SOT-23)
8-Lead Standard Small Outline Package (SOIC_N)
8-Lead Standard Small Outline Package (SOIC_N)
8-Lead Standard Small Outline Package (SOIC_N)
8-Lead Standard Small Outline Package (SOIC_N)
8-Lead Standard Small Outline Package (SOIC_N)
8-Lead Standard Small Outline Package (SOIC_N)
3-Pin Plastic Header-Style Package (TO-92)
3-Pin Plastic Header-Style Package (TO-92)
3-Pin Plastic Header-Style Package (TO-92)
3-Pin Plastic Header-Style Package (TO-92)
3-Pin Plastic Header-Style Package (TO-92)
5-Lead Small Outline Transistor Package (SOT-23)
5-Lead Small Outline Transistor Package (SOT-23)
8-Lead Standard Small Outline Package (SOIC_N)
8-Lead Standard Small Outline Package (SOIC_N)
3-Pin Plastic Header-Style Package (TO-92)
3-Pin Plastic Header-Style Package (TO-92)
3-Pin Plastic Header-Style Package (TO-92)
Rev. F | Page 19 of 20
Package
Option
R-8
RJ-5
RJ-5
R-8
T-3
T-3
RJ-5
R-8
R-8
R-8
R-8
RJ-5
RJ-5
R-8
R-8
R-8
R-8
R-8
R-8
T-3
T-3
T-3
T-3
T-3
RJ-5
RJ-5
R-8
R-8
T-3
T-3
T-3
Branding
T5G
#T11
#T6G
T6G
#T6G
T7G
#T12
TMP35/TMP36/TMP37
AUTOMOTIVE PRODUCTS
The ADW75001Z-0REEL7 model is available with controlled manufacturing to support the quality and reliability requirements of
automotive applications. Note that this automotive model may have specifications that differ from the commercial models; therefore,
designers should review the Specifications section of this data sheet carefully. Only automotive grade products shown are available for use
in automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to
obtain the specific Automotive Reliability reports for these models.
Rev. F | Page 20 of 20