Professional Documents
Culture Documents
BURNER SUSPENSION , BS
70001076-2
VIGERSLEV ALL 77 - 2500 VALBY - DENMARK 2040 AVENUE C - PA 18017-2188 BETHLEHEM USA CAPITAL TOWERS 180. KODAMBAKKAM HIGH ROAD, NUNGAMBAKKAM,- CHENNAI 600 034 - INDIA
70001076-2
Contents:
Page:
1.
GENERAL NOTES
2.
3.
INSTALLATION
4.
5.
MAINTENANCE
10
70001076-2
APPENDICES:
Burner suspension
Carriage
Carriage, sectional view
I
II
III
Editor:
JS
Translator:
JRo
Approved by:
CLKJ
MGN code:
3K01
Pages:
17
70001076-2
NOTE!
The present instruction manual is concerned with the situations which, according to
our experience, are the most likely to occur. An exhaustive enumeration of all conceivable situations which may occur during mounting, operation and maintenance
of the burner suspension cannot be provided.
Consequently, if a situation should arise, the occurrence of which is not foreseen in
the instruction manual, and which the client is/feels unable to handle, we would recommend that FLS be contacted without undue delay for advice on appropriate action.
1.
GENERAL NOTES
Burner suspension type BS is used for the retention and positioning of the kiln
burner on kilns featuring a separate cooler. The burner suspension can be used for
all standard burner types and all normal types of fuel.
70001076-2
2.
3.
70001076-2
INSTALLATION
See Appendices I, II and III.
3.1
Travel rails
ERECTION CHECK
Check the holes in the portals for the installation of cross beams (04)
Mount portals, cross beams for rail suspension (04) and travel rails (09) in accordance with directions given on assembly drawing.
Align the cross beams so that the rails are straight, if necessary by inserting intermediates between the portals and the cross beams.
The portals may be made of concrete or steel. If concrete is used, the bolt holes
must be grouted following the alignment and trial-run of the burner carriage (see
sub-section 3.2.).
Mount cross girders (07) and cross beam (03). (Should not be welded).
Mount cable carriage - including rails for same - in accordance with the directions
on assembly drawing.
3.2
Burner carriage
Dismantle the lower wheels on the carriage (05) and lift it onto the rails (09).
Remount the lower wheels.
The rear wheel set must grip the rail section with one wheel over and one wheel
under the rail.
ERECTION CHECK
Move the carriage forward and backward on the rails by means of the hexagonal
shaft end of the gearbox, and check that the movement of the carriage is not impeded in any way.
Mount the axial bearing (25) with locking ring in the movable cross frame (26) in
accordance with directions given on assembly drawing.
Mount guide pin (24) in the suspension frame (19) exactly as indicated on the
assembly drawing.
Mount the movable cross frame (26) in the front suspension frame so that the
guide pin (24) extends through the axial bearing and the hole in the suspension
frame. Then mount the suspension frame on the carriage.
Mount the handle (29) in accordance with directions on assembly drawing.
70001076-2
7
Lift the rear suspension frame (13) into the carriage so that rollers (32) bear against
the lower side of rail (31). Secure the suspension frame using the appertaining
locking plates (30).
Mount the hydraulic pump (14). Install the hydraulic pipework (18) and connect pump and hydraulic cylinder (16) as indicated on the assembly drawing.
Assemble the cross member (15) and link bearing (33).
Remove stop blocks (35). Lift the cross member onto the suspension frame. Remount the stop blocks (35) and let the cross frame rest on the blocks.
Mount ratchet drive (12) between suspension frame and carriage.
Mount start/stop switches, limit switches as well as power connections to geared
motor (22) in accordance with the wiring diagrams.
Mount light-weight carriages (08) for burner lance (if included in supply).
ERECTION CHECK
Check that motor, limit switches and start/stop switches perform as intended
3.3
Suspension of burner
To prepare the kiln burner for operation, see separate instruction manual for this
unit.
Place the burner on the burners platform under the travels rails with the supporting
beam facing upwards,
Move the burner carriage across the burner so that the front suspension is situated
immediately over the cross pin (27) of the supporting beam. If necessary, the
movable cross frame (26) can be lifted by means of the handles (29).
Remove the locking blocks (28) and safety pin (34) from front and rear suspensions, respectively.
Lift the burner pipe so that the cross pin (27) moves into the slits in the movable
cross frame (26), while, at the same time, the rear fork on supporting beam (06)
engages the shaft in the link bearing (33).
Refit the locking blocks and the safety pin and lock the safety pin. Ease off the
burner pipe so that comes to rest in the carriage. Check also that the hydraulic
piston fits into the recess on the cross member.
Adjust the position of the burner on a provisional basis as indicated in section 2 so
that the burner pipe is flush with the kiln centre line. Final adjustment is carried
out when the burner is positioned in the kiln. See instruction manual for burner.
70001076-2
ERECTION CHECK
Check that locking blocks (28) and safety pin (34) including split pin are correctly
positioned.
4.
OPERATION
After the burner has been positioned in the kiln, and the final adjustment of its position has been carried out, the hydraulic cylinder (14) must be relieved. This is
done by clamping the lock nut (16) fully against the cylinder, with subsequent depressurization of the hydraulic pump (14).
Prior to any downward adjustment of the burner pipe, the hydraulic system
must be pressurized. Afterwards, the lock nut is screwed downward to extent required - towards the cross member, with subsequent de-pressurization
of the hydraulic system.
If a vertical adjustment of the burner pipe is required, the hydraulic system
must be pressurized and the piston must be retracted until the desired position of the burner pipe has been achieved. Afterwards, the lock nut is firmly
tightened against the hydraulic cylinder and the hydraulic system is relieved.
Attention is drawn to the fact that the lock nut must not be adjusted unless
the hydraulic system is pressurized.
70001076-2
In event of power failure which makes it necessary to move the burner carriage out of the kiln to avoid damage to the burner pipe, this must be done
manually, as follows:
Initially, the burner pipe must be adjusted to the horizontal position by pressurizing the hydraulic system, subsequently clamping the lock nut down
against the cross member. Finally, the hydraulic system must be relieved
again.
Now, the burner carriage can be moved out according to any of the two
methods described below::
1. By using a 36 mm ratchet spanner on the hexagonal shaft end of the
gearbox.
2. By pulling out the burner carriage using a suitable rope or similar
means attached to the tow hook at the rear end of the burner carriage.
10
70001076-2
5.
MAINTENANCE
5.1
Text
Burner suspension
Ratchet drive
Hydraulic oil
Gearbox
Geared motor, see
separate instruction manual
Drive wheel
Axial bearing
Roller
Link bearing
.1
A
.2
4A
A
.3
.4
.5
.6
A
A
A
A
A
A
A
5.1.1 Lubrication
The nature and type of lubricants can be seen in FLS Key to Lubricants.
Gearbox (21), drive wheel (23) and rollers (32)
Feed grease through grease nipple. Grease quantity per nipple: Approx. 10 cm3.
Quality: FLS 7425.
Ratchet drive (12), axial bearing (25) and link bearing (33)
Lubricate ratchet and bearings with grease.
Quality: FLS 7425
70001076-2
11
5.1.2 Cleaning
Burner suspension (00)
General cleaning on and around the unit.
Ratchet drive (12)
Remove dirt and old lubricant by means of solar oil and rags.
5.1.6 Performance test
Burner unit (00)
Move all adjusting devices to ensure that their movements are not impeded in any
way.
12
70001076-2
70001076-2
13
14
70001076-2
70001076-2
II
15
16
70001076-2
70001076-2
III
17