Professional Documents
Culture Documents
0006/6
ISO 9001
KM20X NETWORK
CONTROLLER
KM20x
Description
KM20X network controller is an instrument for use in a GIACOKLIMA
bus system destined to the control of Giacobini systems for underfloor
systems or ceiling radiant systems associated with K481 and K483
ambient thermostats, KPM20 unit I/O, KD200 display unit and with
KSMS module.
Signalling elements
On the front of the case of the instrument a red LED signals the
operating state of KM20x Controller.
LED for
operating
state signaling.
CODE
BUILT-IN MODEM
PORT
RS232
PORT
RS485
KM200Y001
NO
KM201Y001
YES
KM202Y001
YES
KM203Y001
NO
Main features
- Possibility to run up to 32 GIACOKLIMA bus instruments connected
on primary bus
- N2 analogical inputs for the connection of active sensors
- N2 analogical inputs for the connection of passive sensors
- Possibility to connect a KD200 Display Unit (only for KM202 version
and KM203 version)
- KM200: Possibility to connect an external modem for remote
control functions
- KM201 and KM202: built-in modem for analogical phone line
- KM203: possibility to connect the KSMS external module for text
messages sending and receiving and for remote control via GSM
phone line.
Analogical alarms
Up to 32 analogical alarms can be configured for each connected
GIACOKLIMA bus device. For each alarm a set of parameters should
be set as:
- alarm type (differentiating between maximum and minimum);
- priority level (low, medium or high);
- hysteresis band.
Digital alarms
Up to 32 digital alarms can be configured for each connected
GIACOKLIMA bus device For each alarm a set of parameters should
be set as:
- priority level (low, medium or high);
- significant transition (up/down front).
Communication alarms
In addition to analogical and digital alarms, the Controller runs also
communication alarms. If in operating mode, during a cyclic polling,
the Controller does not receive the reply from a GIACOKLIMA bus
device, it assumes that this device no longer works and triggers a
corresponding communication alarm. This kind of alarm does not
require any configuration, it is always taken into consideration and
always has the highest priority.
KM20X
KM20x 0319EN September 2007
0006/6
ISO 9001
KM20X NETWORK
CONTROLLER
Remote control
Safety
Device synchronization
An 8 character password can be programmed through the auxiliary
serial port (AUX). When a phone call to the Controller is enabled, it
does not accept the message until the proper password is typed. The
password should be entered .
Installation
Operating mode
At any given moment, KM20x Controller can be only in one of the two
following operating modes:
- operating mode (default);
- configuration mode.
Operating mode
When a KM20x Controller is powered, by default it is in operating
mode. In this operating mode, Controller KM20x carries out its main
functions:
- periodical reading of alarms configured in each GIACOKLIMA bus
device connected;
- real time evaluation of each alarm and generation of alarm flags;
- confrontation between the state of the alarms and their silencing. In
case an alarm has a sufficiently high priority and was not yet silenced,
the Controller enables a phone call to the GIACOMINI Service Center;
- periodical reading of configured trends and storage in the EEPROM
memory. When close to saturation the Controller can be programmed
to call the GIACOMINI Service Center and transfer on the Web Server
the content of memory;
- generation of a communication alarm if a GIACOKLIMA bus device
does not reply to a request of value of the alarm;
- management of messages coming from the GIACOMINI Service
Center.
Connections
KM20x Controller is equipped with terminals to connect several input
and output devices. A faston connection terminal (2 poles) is dedicated
to the connection of 230 V~ network supply. The BUS terminal (4 poles:
RT+, RT-, com, Vs) is dedicated to bus connection.
TERMINAL NUMBER
DESCRIPTION
5-6
Analogical input 1
7-8
Analogical input 2
9-10
Analogical input 3
Configuration mode
11-12
Analogical input
13-14
KM20X
KM20x 0319EN September 2007
0006/6
ISO 9001
KM20X NETWORK
CONTROLLER
Sizes
B
PORT AUX
9 POLES
DISPLAY
PORT PC AT
9 POLES
CD
RX
TX
DTR
RI
S.GND
DSR
RTS
CTS
1
2
3
4
5
6
7
8
9
3
2
Connection cable
PORT PC/PORT AUX
Technical data
KM200Y001
Supply
RS232
or RS-485
Serial port (AUX)
RS232 Serial
port (MAIN)
Phone port
A (out)
Phone port
B (in)
KM203
BUS
BUS
4 x 0.25 mmq
ai dispositivi in campo
RS232 - 19200
baud
RS232 - 19200
baud (1)
port MAIN
tel. port A
RS232
configurable (2)
n.a.
n.a.
phone device
n.a.
phone device
2400 baud
2400 baud
0 - 10 Vcc
0 - 10 Vcc
tel. port B
n.a.
Analogical inputs
AI1 (terminals 5-6)
AI2 (terminals 7-8)
AI3 (terminals 9-10)
AI4 (terminals
11-12)
Warning!
Make sure that power supply is turned off as connections
are performed.
0 - 10 Vcc 0
0 - 10 Vcc 0
0 - 10 Vcc
0 - 10 Vcc
(NTC) 0 - 50
(NTC) 0 - 50C
(NTC) 0 - 50C
(NTC) 0 - 50
(NTC) 0 - 50C
(NTC) 0 - 50C
Supply sensors
active
(terminals 9-10
and 11-12)
n.a.
n.a.
+15 Vcc
Primary Bus
(terminals 1, 2, 3, 4)
RS485 - 9600
Baud
RS485 - 9600
Baud
RS485 - 9600
Baud
max. length
shielded cable
from port AUX
to PC
10 m
10 m
10 m
32
32
32
Transformer
Absorption
Operating
environment
conditions
Relative
humidity
VDE Standards
6 VA
VDE Standards
6 VA
VDE Standards
6 VA
from
0 to + 40 C
from
0 to + 40 C
from
0 to + 40 C
Storage
environment
conditions
from
-25 to 70 C
from
-25 to 70 C
from
-25 to 70 C
Sizes
(AxBxC)
125x108x57 mm
125x108x57 mm
125x108x57 mm
0,5 kg
0,5 kg
0,6 kg
Protection
degree
IP30
IP30
IP30
ApprovalsMarking CE
EN55022,
EN55024,
EN60950,
EN61000-3-2,
EN61000-3-3
EN55022,
EN55024,
EN60950,
EN61000-3-2,
EN61000-3-3
EN55022,
EN55024,
EN60950,
EN61000-3-2,
EN61000-3-3
BUS KSMS
4 x 0.25 mmq
Weight
230 V~
KM202Y001 e
KM203Y001
Transmission:
port AUX
Case material
BUS GK
KM201Y001
KM20X
KM20x 0319EN September 2007
0006/6
ISO 9001
KM20X NETWORK
CONTROLLER
Additional information
For further information visit site www.giacomini.com or contact
technical service:
+39 0322 923372
+39 0322 923255
consulenza.prodotti@giacomini.com
This communication is for information purposes. Giacomini S.p.A. reserves the
right to make at any moment, without prior notice, modifications for technical
or commercial reasons to the items contained hereby. The information of this
technical communication does not exempt the user from strictly following
existing good practice regulations and standards.
Giacomini S.p.A. Via per Alzo, 39 I-28017 San Maurizio dOpaglio (NO) Italy