You are on page 1of 17

Cisco.Test-inside.642-813.v2013-11-01.by.Jack.Cross.

197q
Number: 642-813
Passing Score: 900
Time Limit: 120 min
File Version: 12.5

Exam Code: 642-813


Exam Name: Cisco implementing cisco switched networks

Hotspot (11 Q)
QUESTION 1

During routine maintenance, GigabitEthernet1/0/1 on DSW1 was shut down. All other interfaces were up.
DSW2 became the active HSRP device for VLAN 101 as desired. However, after GigabitEthernet1/0/1 on
DSW1 was reactivated, DSW1 did not become the active router for VLAN 101 as desired. What needs to be
done to make the group for VLAN 101 function properly?
A. Enable preempt in the VLAN 101 HSRP group on DSW1
B. Disable preempt in the VLAN 101 HSRP group on DSW2s
C. In the VLAN 101 HSRP group on DSW1, decrease the priority value to a value that is less than the priority
value configured in the VLAN 101 HSRP group on DSW2
D. Decrease the decrement value in the track command for the VLAN 101 HSRP group on DSW1s to a
values less that the value in the track command for the VLAN 101 HSRP group on DSW2
Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 2

During routine maintenance, it became necessary to shut down the GigabitEthernet1/0/1 interface on DSW1.
All other interfaces were up. During this time DSW1 remained the active device for the VLAN 102 HSRP group.
You have determined that there is an issue with the decrement value in the track command for the VLAN 102
HSRP group. What need to be done to make the group function properly?
A.
B.
C.
D.
E.

The decrement value on DSW1 should be greater than 5 and less than 15
The decrement value on DSW1 should be greater than 9 and less than 15
The decrement value on DSW1 should be greater than 11 and less than 19
The decrement value on DSW1 should be greater than 190 and less than 200
The decrement value on DSW1 should be greater than 195 and less than 205

Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 3

All interfaces are active. DSW2 has not become the active device for the VLAN 103 HSRP group. As related to
the VLAN 103 HSRP group, what can be done to make the group function properly?
A.
B.
C.
D.

On DSW1, disable preempt


On DSW1, decrease the priority value to a value less than 190 and greater than 150
On DSW2, increase the priority value to a value greater 200 and less than 250
On DSW2, increase the decrement value in the track command to a value greater than 10 and less than 50

Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 4

During routine maintenance, it became necessary to shut down the GigabitEthernet1/0/1 interface on DSW1
and DSW2. All other interfaces were up. During this time, DSW1 became the active router for the VLAN 104
HSRP group. As related to the VLAN 104 HSRP group, what can to be done to make the group function
properly?
A.
B.
C.
D.

On DSW1, disable preempt


On DSW2 decrease the priority value to a value less than 150
On DSW1, increase the decrement value in the track command to a value greater than 6
On DSW1, decrease the decrement value in the track command to a value less than 1

Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:
QUESTION 5

What is the priority value of the VLAN 105 HSRP group on DSW2?
A.
B.
C.
D.

50
100
150
200

Correct Answer: B
Section: (none)
Explanation
Explanation/Reference:
QUESTION 6

If GigabitEthernet1/0/1 on DSW2 is shut down, what will be the resulting priority value of the VLAN 1015 HSRP
group on router DSW2?
A.
B.
C.
D.

90
100
150
200

Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 7

Which port state is interface Fa0/2 of switch SW-B in for VLAN1 and 175?
A. Blocking
B. Disabled

C.
D.
E.
F.

Discarding
Forwarding
Learning
Listening

Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 8

Which Spanning Tree Protocol has been implemented on switch SW-B?


A.
B.
C.
D.

PVST+
PVRST
MSTP/IEEE 802.1s
STP/IEEE 802.1D

Correct Answer: A
Section: (none)
Explanation
Explanation/Reference:
QUESTION 9

Which bridge ID belongs to switch SW-A?


A.
B.
C.
D.
E.
F.

24623.000f.34f5.0138
32768.000d.bd03.0380
32768.000d.65db.0102
32769.000d.65db.0102
32874.000d.db03.0380
32815.000d.db03.0380

Correct Answer: D
Section: (none)
Explanation

Explanation/Reference:
QUESTION 10

Which port role has interface Fa0/2 of switch SW-A adopted for VLAN 44?
A.
B.
C.
D.
E.

Alternate port
Backup port
Designated port
Root port
Nondesignated port

Correct Answer: C
Section: (none)
Explanation
Explanation/Reference:

You might also like