Professional Documents
Culture Documents
Base plate (1004) creates a base plate that is connected to a column end.
Use for
Situation
Description
Simple base plate detail
Cast plate
Selection order
1. Select the main part (column).
2. Pick a position.
The detail is created automatically.
See also
Base plate (1004): Picture tab
Base plate (1004): Parts tab
Base plate (1004): Parameters tab
General tab
Base plate (1004): Bolts tab
Base plate (1004): Anchor rods tab
Base plate (1004): Extra plates tab
Analysis tab
NO.
Part
Base plate
Shim plate
Leveling plate
Grout
Cast plate
Shear key
Anchor rod
Extra plate 1
Extra plate 2
Dimensions
NO.
Description
Define the distance from the flange to the edge of the base plate.
Enter a negative value to make the base plate larger.
Define the weld gap.
Define the height of the shear key.
Description
Define the shear key vertical
offset from the column
center.
Define the shear key
horizontal offset from the
column center.
Plate
Part
Description
Default
Plate
Additional
beam
Leveling plate
thickness = 1/4
Fitting plate
Number of
fitting pl.
Leveling plate
hole diameter
Key profile
welded to
Field
Description
Default
Pos_No
Material
Name
BASEPLATE
Description
Default
30 mm
30 mm
Description
Default
Holes are based on the bolt group of the detail.
AutoDefaults can change this option.
Tolerance
Define the tolerance for the slots in finger shim plates. The width of the slot is the bolt diameter + the
tolerance.
Grout hole
Define whether a grout hole is created in the base plate. The hole is also created in the leveling plate
and shim plates, if they exist in the detail.
Option
Description
Default
Grout hole is not created.
AutoDefaults can change this option.
Description
Define the location of the grout hole from the center of the column in the direction of
the web.
Define the location of the grout hole from the center of the column in the direction of
the flange.
Gap size
Define the limit value for the gap between the base plate and the column. Use this when the column is
slightly inclined.
If the actual gap is smaller than this value, the end of the column is left straight.
If the actual gap is larger than this value, the end of the column is fitted to the base plate.
Field
Description
Component
Attributes
Enter the name of the attribute file for the selected component.
Input
Description
Define how to measure the dimensions for horizontal bolt group position.
Left: From the left edge of the secondary part to the leftmost bolt.
Middle: From the center line of the secondary part to the center line of the bolts.
Right: From the right edge of the secondary part to the rightmost bolt.
Description
Define how to measure the dimensions for vertical bolt group position.
Top: From the upper edge of the secondary part to the uppermost bolt.
Middle: From the center line of the bolts to the center line of the secondary part.
Below: From the lower edge of the secondary part to the lowest bolt.
Description
Default
Bolt size
Bolt diameter.
Bolt standard
Tolerance
Thread in mat
Yes
Site/Workshop
Slotted holes
You can define slotted, oversized, or tapped holes.
Site
Option
Description
Default
0,
0,
Hole type
Rotate
Slots
Slots in
which results in a
round hole.
which results in a
round hole.
Bolt assembly
The selected check boxes define which component objects (bolt, washers, and nuts) are used in the bolt
assembly.
If you want to create a hole only, clear all the check boxes.
To modify the bolt assembly in an existing component, select the Effect in modify check box and click
Modify.
Description
Nut profile
Washer profile
Plate washer
Castplate
Description
Default
Pos_No
Material
Option
Description
Name
Class
Default
Description
Default
500 mm
Description
Default
Define the length of the anchor rod above the base plate.
50 mm
Define the distance between the cast plate and the base
plate.
60 mm
0 mm
Description
Default
Type 1
AutoDefaults can change
this option.
Type 1
a
Radius of the hook
a = 2*anchor
diameter
b
Width of the hook
b = 1/5
a
Radius of the hook
c = same
b
Width of the hook
c
bar
of anchor bar
length
the hook
as width of
Option
Description
d
Length of the anchor rod
below the extra plate
d = 4*nut
e
Length of the lower
thread
e = 2*nut
Hook direction
Option
Description
Default
Type 1
AutoDefaults can change this option.
Type 1
Type 2
Type 3
Type 4
size plus
thickness of extra
plate
size
Bolting direction
You can define the bolting direction if you have created the base
plate with bolts.
Option
Description
Default
Bolting direction 1
AutoDefaults can change this option.
Bolting direction 1
Bolting direction 2
Description
Default
Castplate holes
tolerance
same as bolt
tolerance
Description
Grout thickness
Grouting helps you to model columns to the top of concrete parts and place the base plate correctly. It
also makes it easier to dimension the detail in GA drawings.
By default, no grouting is created.
In the first field, enter the grout thickness.
In the second field, define whether the grouting is created above or below the detail creation point. This
also affects the shim plates.
Create
Description
Part dimensions
Part
Description
Default
Extra profile
1
PL10*100
Extra profile
2
Part properties
Option
Description
Default
Pos_No
Material
Name
Class
Description
Default
50 mm
Description
Default
Type 1
AutoDefaults can change this option.
Type 1
Option
Description
Type 2
Type 3
Description
Default
Description
Default
Type 1
AutoDefaults can change this option.
Type 1
Type 2
Type 3
Type 4
Option
Description
Type 5
Type 6
Description
Default
Define the length of extra profile 2 from the axis of the anchor bar.
50 mm
Description
Default
Type 1
AutoDefaults can change this option.
Type 1
Type 2
Description
Default
Hole tolerance
Profile rotation
Front
Option
Description
Default
Front