Professional Documents
Culture Documents
SN7414, SN74LS14
HEX SCHMITT-TRIGGER INVERTERS
SDLS049B DECEMBER 1983 REVISED FEBRUARY 2002
D
D
D
1A
1Y
2A
2Y
3A
3Y
GND
description
Each circuit functions as an inverter, but because
of the Schmitt action, it has different input
threshold levels for positive-going (VT+) and
negative-going (VT) signals.
These circuits are temperature compensated and
can be triggered from the slowest of input ramps
and still give clean, jitter-free output signals.
14
13
12
11
10
VCC
6A
6Y
5A
5Y
4A
4Y
1Y
1A
NC
VCC
6A
SN54LS14 . . . FK PACKAGE
(TOP VIEW)
3 2 1 20 19
18
17
16
15
14
9 10 11 12 13
6Y
NC
5A
NC
5Y
3Y
GND
NC
4Y
4A
2A
NC
2Y
NC
3A
NC No internal connection
ORDERING INFORMATION
PACKAGE
TA
TOP-SIDE
MARKING
Tube
SN7414N
SN7414N
Tube
SN74LS14N
SN74LS14N
Tube
SN7414D
SN7414DR
Tube
SN74LS14D
SN74LS14DR
SOP NS
SN7414NSR
SN7414
SSOP DB
SN74LS14DBR
LS14
Tube
SN5414J
SN5414J
Tube
SNJ5414J
SNJ5414J
Tube
SN54LS14J
SN54LS14J
Tube
SNJ54LS14J
SNJ54LS14J
Tube
SNJ5414W
SNJ5414W
Tube
SNJ54LS14W
SNJ54LS14W
Tube
SNJ54LS14FK
PDIP N
0C to 70C
ORDERABLE
PART NUMBER
SOIC D
CDIP J
55C to 125C
CFP W
LCCC FK
7414
LS14
SNJ54LS14FK
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are
available at www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright 2002, Texas Instruments Incorporated
SN5414, SN54LS14,
SN7414, SN74LS14
HEX SCHMITT-TRIGGER INVERTERS
SDLS049B DECEMBER 1983 REVISED FEBRUARY 2002
1Y
2A
2Y
3A
3Y
4A
4Y
5A
11
10
5Y
6A
13
12
6Y
Y=A
Pin numbers shown are for the D, DB, J, N, NS, and W packages.
SN5414, SN54LS14,
SN7414, SN74LS14
HEX SCHMITT-TRIGGER INVERTERS
SDLS049B DECEMBER 1983 REVISED FEBRUARY 2002
schematic
14
VCC
100
6 k
Output Y
Input A
GND
LS14
VCC
20 k
Output Y
Input A
GND
Resistor values shown are nominal.
SN5414, SN54LS14,
SN7414, SN74LS14
HEX SCHMITT-TRIGGER INVERTERS
SDLS049B DECEMBER 1983 REVISED FEBRUARY 2002
absolute maximum ratings over operating free-air temperature (unless otherwise noted)
Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage: 14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
LS14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Package thermal impedance, JA (see Note 2): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86C/W
DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96C/W
N package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80C/W
NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76C/W
Storage temperaturerange, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65C to 150C
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. Voltage values are with respect to network ground terminal.
2. The package termal impedance is calculated in accordance with JESD 51-7
Supply voltage
IOL
TA
MIN
NOM
4.5
SN7414
MIN
NOM
MAX
5.5
4.75
5.25
0.8
mA
16
mA
70
0.8
16
55
UNIT
MAX
125
TEST CONDITIONS
PARAMETER
MIN
TYP
UNIT
MAX
VT+
VT
VCC = 5 V
VCC = 5 V
1.5
1.7
0.6
0.9
1.1
Hysteresis
(VT+ VT)
VCC = 5 V
0.4
0.8
VIK
VOH
VCC = MIN,
VCC = MIN,
II = 12 mA
VI = 0.6 V,
VOL
IT+
VCC = MIN,
VCC = 5 V,
VI = 2 V,
VI = VT+
IT
II
VCC = 5 V,
VCC = MAX,
VI = VT
VI = 5.5 V
IIH
IIL
VCC = MAX,
VCC = MAX,
VIH = 2.4 V
VIL = 0.4 V
IOS
ICCH
VCC = MAX
V
1.5
IOH = 0.8 mA
IOL = 16 mA
2.4
3.4
0.2
V
0.4
0.43
mA
1
mA
40
1.2
mA
55
mA
22
36
mA
ICCL
39
For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions.
All typical values are at VCC = 5 V, TA = 25C.
Not more than one output should be shorted at a time.
60
mA
18
V
mA
0.56
0.8
VCC = MAX
VCC = MAX
SN5414, SN54LS14,
SN7414, SN74LS14
HEX SCHMITT-TRIGGER INVERTERS
SDLS049B DECEMBER 1983 REVISED FEBRUARY 2002
FROM
(INPUT)
TO
(OUTPUT)
tPLH
SN5414
SN7414
TEST CONDITIONS
MIN
RL = 400
,
tPHL
UNIT
TYP
MAX
15
22
15
22
CL = 15 pF
F
ns
SN74LS14
UNIT
MIN
NOM
MAX
MIN
NOM
MAX
4.5
5.5
4.75
5.25
VCC
IOH
Supply voltage
High-level output current
0.4
0.4
mA
IOL
TA
mA
70
55
125
TEST CONDITIONS
PARAMETER
SN74LS14
MIN TYP
MAX
UNIT
VT+
VT
VCC = 5 V
VCC = 5 V
1.4
1.6
1.9
1.4
1.6
1.9
0.5
0.8
0.5
0.8
Hysteresis
(VT+ VT)
VCC = 5 V
0.4
0.8
0.4
0.8
VIK
VOH
VCC = MIN,
VCC = MIN,
II = 18 mA
VI = 0.5 V,
2.5
3.4
2.7
3.4
VOL
VCC = MIN
MIN,
VI = 1.9
19V
IT+
IT
VCC = 5 V,
VCC = 5 V,
VI = VT+
VI = VT
II
IIH
VCC = MAX,
VCC = MAX,
VI = 7 V
VIH = 2.7 V
0.1
20
20
IIL
IOS
VCC = MAX,
VCC = MAX
VIL = 0.4 V
0.4
0.4
mA
100
mA
ICCH
ICCL
VCC = MAX
VCC = MAX
1.5
IOH = 0.4 mA
IOL= 4 mA
0.25
1.5
0.4
IOL = 8 mA
0.14
0.25
0.4
0.35
0.5
mA
0.1
20
V
mA
0.18
100
V
V
0.14
0.18
20
mA
8.6
16
8.6
16
mA
12
21
12
21
mA
TYP
MAX
15
22
15
22
For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions.
All typical values are at VCC = 5 V, TA = 25C.
Not more than one output should be shorted at a time, and duration of the short-circuit should not exceed one second.
FROM
(INPUT)
TO
(OUTPUT)
tPHL
TEST CONDITIONS
RL = 2 k
k,
CL = 15 pF
F
MIN
UNIT
ns
SN5414, SN54LS14,
SN7414, SN74LS14
HEX SCHMITT-TRIGGER INVERTERS
SDLS049B DECEMBER 1983 REVISED FEBRUARY 2002
VCC
RL
From Output
Under Test
CL
(see Note A)
CL
(see Note A)
High-Level
Pulse
1.5 V
S2
LOAD CIRCUIT
FOR 3-STATE OUTPUTS
3V
Timing
Input
1.5 V
1 k
Test
Point
LOAD CIRCUIT
FOR OPEN-COLLECTOR OUTPUTS
LOAD CIRCUIT
FOR 2-STATE TOTEM-POLE OUTPUTS
S1
(see Note B)
CL
(see Note A)
RL
(see Note B)
RL
From Output
Under Test
VCC
From Output
Under Test
Test
Point
1.5 V
0V
tw
Low-Level
Pulse
1.5 V
tsu
Data
Input
1.5 V
VOLTAGE WAVEFORMS
PULSE DURATIONS
1.5 V
1.5 V
In-Phase
Output
(see Note D)
tPHL
VOH
1.5 V
Out-of-Phase
Output
(see Note D)
0V
1.5 V
1.5 V
Waveform 1
(see Notes C
and D)
tPLZ
VOH
1.5 V
1.5 V
VOL
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
1.5 V
1.5 V
VOL
tPZH
tPLH
1.5 V
0V
tPZL
VOL
tPHL
1.5 V
3V
Output
Control
(low-level
enabling)
0V
tPLH
3V
1.5 V
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
3V
Input
th
Waveform 2
(see Notes C
and D)
VOL + 0.5 V
tPHZ
VOH
1.5 V
VOH 0.5 V
1.5 V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES, 3-STATE OUTPUTS
SN5414, SN54LS14,
SN7414, SN74LS14
HEX SCHMITT-TRIGGER INVERTERS
SDLS049B DECEMBER 1983 REVISED FEBRUARY 2002
VCC
RL
(see Note B)
From Output
Under Test
CL
(see Note A)
High-Level
Pulse
1.3 V
S2
LOAD CIRCUIT
FOR 3-STATE OUTPUTS
3V
Timing
Input
1.3 V
5 k
Test
Point
LOAD CIRCUIT
FOR OPEN-COLLECTOR OUTPUTS
LOAD CIRCUIT
FOR 2-STATE TOTEM-POLE OUTPUTS
S1
(see Note B)
CL
(see Note A)
RL
CL
(see Note A)
RL
From Output
Under Test
VCC
From Output
Under Test
Test
Point
1.3 V
0V
tw
Low-Level
Pulse
1.3 V
tsu
0V
In-Phase
Output
(see Note D)
3V
1.3 V
1.3 V
0V
tPZL
tPLZ
tPHL
VOH
1.3 V
1.3 V
Waveform 1
(see Notes C
and D)
VOL
tPZH
tPLH
VOH
1.3 V
1.3 V
VOL
Waveform 2
(see Notes C
and D)
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
1.5 V
1.3 V
VOL
tPHL
Out-of-Phase
Output
(see Note D)
1.3 V
0V
Output
Control
(low-level
enabling)
1.3 V
tPLH
1.3 V
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
3V
1.3 V
3V
Data
Input
1.3 V
VOLTAGE WAVEFORMS
PULSE DURATIONS
Input
th
VOL + 0.5 V
tPHZ
VOH
1.3 V
VOH 0.5 V
1.5 V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES, 3-STATE OUTPUTS
SN5414, SN54LS14,
SN7414, SN74LS14
HEX SCHMITT-TRIGGER INVERTERS
SDLS049B DECEMBER 1983 REVISED FEBRUARY 2002
VCC = 5 V
1.70
1.69
1.68
1.67
1.66
1.65
1.64
1.63
1.62
1.61
1.60
VCC = 5 V
0.89
0.88
0.87
0.86
0.85
0.84
0.83
0.82
0.81
0.80
75 50
25
25
50
75
100
125
75 50
25
25
50
75
100
TA Free-Air Temperature C
TA Free-Air Temperature C
Figure 3
Figure 4
HYSTERESIS
vs
FREE-AIR TEMPERATURE
850
VCC = 5 V
840
V T+ V T Hysteresis mV
830
820
810
800
790
780
770
760
750
75 50
25
25
50
75
100
125
TA Free-Air Temperature C
Figure 5
Data for temperatures below 0C and above 70C and supply voltage below 4.75 V and above 5.25 V are applicable for SN5414 only.
125
SN5414, SN54LS14,
SN7414, SN74LS14
HEX SCHMITT-TRIGGER INVERTERS
SDLS049B DECEMBER 1983 REVISED FEBRUARY 2002
DISTRIBUTION OF UNITS
FOR HYSTERESIS
2.0
VCC = 5 V
TA = 25C
TA = 25C
1.8
Threshold Voltage - V
1.6
Positive-Going Threshold Voltage, VT+
1.4
1.2
1.0
0.8
740
760
780
800
820
840
860
880
900
5.25
5
4.75
VT+ VT Hysteresis mV
4.5
VT+ VT Hysteresis mV
Figure 6
Figure 7
OUTPUT VOLTAGE
vs
INPUT VOLTAGE
HYSTERESIS
vs
SUPPLY VOLTAGE
4
2.0
VCC = 5 V
TA = 25C
TA = 25C
1.8
VT
VT+
1.6
VO Output Voltage V
V T+ VT Hysteresis V
5.5
1.4
1.2
1.0
0.8
0.6
1
0.4
0.2
0
0
4.5
5
5.25
4.75
VCC Supply Voltage V
5.5
0.4
0.8
1.2
1.6
Figure 8
Figure 9
Data for temperatures below 0C and above 70C and supply voltage below 4.75 V and above 5.25 V are applicable for SN5414 only.
SN5414, SN54LS14,
SN7414, SN74LS14
HEX SCHMITT-TRIGGER INVERTERS
SDLS049B DECEMBER 1983 REVISED FEBRUARY 2002
VCC = 5 V
1.69
1.70
1.68
1.67
1.66
1.65
1.64
1.63
1.62
1.61
0.88
0.87
0.86
0.85
0.84
0.83
0.82
0.81
1.60
75 50
25
25
50
75
100
VCC = 5 V
0.89
0.80
125
0
25
50
75 100
25
TA Free-Air Temperature C
75 50
TA Free-Air Temperature C
125
Figure 11
Figure 10
HYSTERESIS
vs
FREE-AIR TEMPERATURE
DISTRIBUTION OF UNITS
FOR HYSTERESIS
850
V T+ VT Hysteresis V
VCC = 5 V
TA = 25C
VCC = 5 V
840
830
820
810
800
790
780
770
99% ARE
ABOVE
735 mV
760
750
75 50
25
25
50
75
100
125
TA Free-Air Temperature C
720
740
760
780
800
820
840
860
880
VT+ VT Hysteresis mV
Figure 12
Figure 13
Data for temperatures below 0C and above 70C and supply voltage below 4.75 V and above 5.25 V are applicable for SN5414 only.
10
SN5414, SN54LS14,
SN7414, SN74LS14
HEX SCHMITT-TRIGGER INVERTERS
SDLS049B DECEMBER 1983 REVISED FEBRUARY 2002
OUTPUT VOLTAGE
vs
INPUT VOLTAGE
2.0
4
VCC = 5 V
TA = 25C
TA = 25C
1.8
VT
VT+
1.4
VO Output Voltage V
Threshold Voltage V
1.6
1.2
Negative-Going Threshold Voltage, VT
1.0
0.8
Hysteresis, VT+ VT
0.6
1
0.4
0.2
0
0
4.5
4.75
5.25
5.5
0.4
0.8
1.2
1.6
VI Input Voltage V
Figure 15
Figure 14
Data for temperatures below 0C and above 70C and supply voltage below 4.75 V and above 5.25 V are applicable for SN5414 only.
11
SN5414, SN54LS14,
SN7414, SN74LS14
HEX SCHMITT-TRIGGER INVERTERS
SDLS049B DECEMBER 1983 REVISED FEBRUARY 2002
TTL System
VT+
VT
Input
CMOS
Sine-Wave
Oscillator
Output
Pulse Shaper
0.1 Hz to 10 MHz
VT+
330
VT
Input
Input
Output
Threshold Detector
Multivibrator
Open-Collector
Output
Input
Input
A
Output
Point A
Output
Pulse Stretcher
12
VT+
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TIs terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TIs
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Low Power
Wireless
www.ti.com/lpw
Telephony
www.ti.com/telephony
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright 2007, Texas Instruments Incorporated
18-Sep-2008
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
5962-9665801Q2A
ACTIVE
LCCC
FK
20
TBD
5962-9665801QCA
ACTIVE
CDIP
14
TBD
5962-9665801QDA
ACTIVE
CFP
14
5962-9665801VCA
ACTIVE
CDIP
14
5962-9665801VDA
ACTIVE
CFP
14
JM38510/31302BCA
ACTIVE
CDIP
SN5414J
ACTIVE
CDIP
SN54LS14J
ACTIVE
CDIP
SN7414D
ACTIVE
SN7414DE4
Lead/Ball Finish
TBD
A42
TBD
A42 SNPB
TBD
A42
14
TBD
A42 SNPB
14
TBD
A42 SNPB
14
TBD
A42 SNPB
SOIC
14
50
CU NIPDAU
Level-1-260C-UNLIM
ACTIVE
SOIC
14
50
CU NIPDAU
Level-1-260C-UNLIM
SN7414DG4
ACTIVE
SOIC
14
50
CU NIPDAU
Level-1-260C-UNLIM
SN7414DR
ACTIVE
SOIC
14
CU NIPDAU
Level-1-260C-UNLIM
SN7414DRE4
ACTIVE
SOIC
14
CU NIPDAU
Level-1-260C-UNLIM
SN7414DRG4
ACTIVE
SOIC
14
CU NIPDAU
Level-1-260C-UNLIM
SN7414N
ACTIVE
PDIP
14
CU NIPDAU
25
Pb-Free
(RoHS)
TBD
Call TI
25
Pb-Free
(RoHS)
CU NIPDAU
SN7414N3
OBSOLETE
PDIP
14
SN7414NE4
ACTIVE
PDIP
14
SN7414NSR
ACTIVE
SO
NS
14
CU NIPDAU
Level-1-260C-UNLIM
SN7414NSRE4
ACTIVE
SO
NS
14
CU NIPDAU
Level-1-260C-UNLIM
SN7414NSRG4
ACTIVE
SO
NS
14
CU NIPDAU
Level-1-260C-UNLIM
SN74LS14D
ACTIVE
SOIC
14
CU NIPDAU
Level-1-260C-UNLIM
SN74LS14DBR
ACTIVE
SSOP
DB
14
CU NIPDAU
Level-1-260C-UNLIM
SN74LS14DBRE4
ACTIVE
SSOP
DB
14
CU NIPDAU
Level-1-260C-UNLIM
SN74LS14DBRG4
ACTIVE
SSOP
DB
14
CU NIPDAU
Level-1-260C-UNLIM
SN74LS14DE4
ACTIVE
SOIC
14
50
CU NIPDAU
Level-1-260C-UNLIM
SN74LS14DG4
ACTIVE
SOIC
14
50
CU NIPDAU
Level-1-260C-UNLIM
SN74LS14DR
ACTIVE
SOIC
14
CU NIPDAU
Level-1-260C-UNLIM
SN74LS14DRE4
ACTIVE
SOIC
14
CU NIPDAU
Level-1-260C-UNLIM
SN74LS14DRG4
ACTIVE
SOIC
14
CU NIPDAU
Level-1-260C-UNLIM
50
Addendum-Page 1
Call TI
18-Sep-2008
Orderable Device
Status (1)
Package
Type
Package
Drawing
SN74LS14N
ACTIVE
PDIP
14
Lead/Ball Finish
no Sb/Br)
25
Pb-Free
(RoHS)
CU NIPDAU
TBD
Call TI
25
Pb-Free
(RoHS)
CU NIPDAU
SN74LS14N3
OBSOLETE
PDIP
14
SN74LS14NE4
ACTIVE
PDIP
14
Call TI
SN74LS14NSR
ACTIVE
SO
NS
14
CU NIPDAU
Level-1-260C-UNLIM
SN74LS14NSRE4
ACTIVE
SO
NS
14
CU NIPDAU
Level-1-260C-UNLIM
SN74LS14NSRG4
ACTIVE
SO
NS
14
CU NIPDAU
Level-1-260C-UNLIM
SNJ5414J
ACTIVE
CDIP
14
TBD
A42 SNPB
A42
SNJ5414W
ACTIVE
CFP
14
TBD
SNJ54LS14FK
ACTIVE
LCCC
FK
20
TBD
SNJ54LS14J
ACTIVE
CDIP
14
TBD
A42 SNPB
SNJ54LS14W
ACTIVE
CFP
14
TBD
A42
(1)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 2
11-Mar-2008
Device
SN7414DR
SPQ
Reel
Reel
Diameter Width
(mm) W1 (mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
SOIC
14
2500
330.0
16.4
6.5
9.0
2.1
8.0
16.0
Q1
SN7414NSR
SO
NS
14
2000
330.0
16.4
8.2
10.5
2.5
12.0
16.0
Q1
SN74LS14DBR
SSOP
DB
14
2000
330.0
16.4
8.2
6.6
2.5
12.0
16.0
Q1
SN74LS14DR
SOIC
14
2500
330.0
16.4
6.5
9.0
2.1
8.0
16.0
Q1
SN74LS14NSR
SO
NS
14
2000
330.0
16.4
8.2
10.5
2.5
12.0
16.0
Q1
Pack Materials-Page 1
11-Mar-2008
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
SN7414DR
SOIC
14
2500
346.0
346.0
33.0
SN7414NSR
SO
NS
14
2000
346.0
346.0
33.0
SN74LS14DBR
SSOP
DB
14
2000
346.0
346.0
33.0
SN74LS14DR
SOIC
14
2500
346.0
346.0
33.0
SN74LS14NSR
SO
NS
14
2000
346.0
346.0
33.0
Pack Materials-Page 2
MECHANICAL DATA
MSSO002E JANUARY 1995 REVISED DECEMBER 2001
DB (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
28 PINS SHOWN
0,38
0,22
0,65
28
0,15 M
15
0,25
0,09
8,20
7,40
5,60
5,00
Gage Plane
1
14
0,25
08
0,95
0,55
Seating Plane
2,00 MAX
0,10
0,05 MIN
PINS **
14
16
20
24
28
30
38
A MAX
6,50
6,50
7,50
8,50
10,50
10,50
12,90
A MIN
5,90
5,90
6,90
7,90
9,90
9,90
12,30
DIM
4040065 /E 12/01
NOTES: A.
B.
C.
D.
MECHANICAL DATA
MLCC006B OCTOBER 1996
FK (S-CQCC-N**)
28 TERMINAL SHOWN
18
17
16
15
14
13
NO. OF
TERMINALS
**
12
19
11
20
10
MIN
MAX
MIN
MAX
20
0.342
(8,69)
0.358
(9,09)
0.307
(7,80)
0.358
(9,09)
28
0.442
(11,23)
0.458
(11,63)
0.406
(10,31)
0.458
(11,63)
21
22
44
0.640
(16,26)
0.660
(16,76)
0.495
(12,58)
0.560
(14,22)
23
52
0.739
(18,78)
0.761
(19,32)
0.495
(12,58)
0.560
(14,22)
24
6
68
0.938
(23,83)
0.962
(24,43)
0.850
(21,6)
0.858
(21,8)
84
1.141
(28,99)
1.165
(29,59)
1.047
(26,6)
1.063
(27,0)
B SQ
A SQ
25
26
27
28
4
0.080 (2,03)
0.064 (1,63)
0.020 (0,51)
0.010 (0,25)
0.020 (0,51)
0.010 (0,25)
0.055 (1,40)
0.045 (1,14)
0.045 (1,14)
0.035 (0,89)
0.045 (1,14)
0.035 (0,89)
0.028 (0,71)
0.022 (0,54)
0.050 (1,27)
4040140 / D 10/96
NOTES: A.
B.
C.
D.
E.
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TIs terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TIs standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee Solutions
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright 2008, Texas Instruments Incorporated