Professional Documents
Culture Documents
PART 1 GENERAL
1.3 REFERENCES
15060-1
A. American Society of Mechanical Engineers (ASME) B31.1 - Power Piping (SI Edition).
D. ASTM International (ASTM) A36 - Standard Specification for Carbon Structural Steel.
E. ASTM International (ASTM) A47 - Standard Specification for Ferritic Malleable Iron
Castings.
F.
ASTM International (ASTM) A48 - Standard Specification for Gray Iron Castings.
G. ASTM International (ASTM) A53 - Standard Specification for Pipe, Steel, Black and HotDipped, Zinc-Coated, Welded and Seamless.
H. ASTM International (ASTM) A123 - Standard Specification for Zinc (Hot-Dip Galvanized)
Coatings on Iron and Steel Products.
I.
ASTM International (ASTM) A240 - Standard Specification for Chromium and ChromiumNickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General
Applications.
J.
ASTM International (ASTM) A387 - Standard Specification for Pressure Vessel Plates,
Alloy Steel, Chromium-Molybdenum.
K. ASTM International (ASTM) A515 - Standard Specification for Pressure Vessel Plates,
Carbon Steel, for Intermediate-and Higher-Temperature Service.
L. ASTM International (ASTM) A536 - Standard Specification for Ductile Iron Castings.
15060-2
M. ASTM International (ASTM) A575 - Standard Specification for Steel Bars, Carbon,
Merchant Quality, M-Grades.
N. ASTM International (ASTM) A668 - Standard Specification for Steel Forgings, Carbon
and Alloy, for General Industrial Use.
O. ASTM International (ASTM) A1011 - Standard Specification for Steel, Sheet and Strip,
Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy and High-Strength Low-Alloy
with Improved Formability.
P.
Q. Manufacturers Standardization Society of The Valve and Fittings Industry (MSS) SP-58
Pipe Hangers and Supports - Materials, Design and Manufacture.
R. Manufacturers Standardization Society of The Valve and Fittings Industry (MSS) SP-69
Pipe Hangers and Supports - Selection and Application.
S. Manufacturers Standardization Society of The Valve and Fittings Industry (MSS) SP-77
Guidelines for Pipe Support Contractual Relationships.
T.
Manufacturers Standardization Society of The Valve and Fittings Industry (MSS) SP-89
Pipe Hangers and Supports - Fabrication and Installation Practices.
U. Manufacturers Standardization Society of The Valve and Fittings Industry (MSS) SP-90
Guidelines on Terminology for Pipe Hangers and Supports.
V. Manufacturers Standardization Society of The Valve and Fittings Industry (MSS) SP-127
Bracing for Piping Systems Seismic-Wind-Dynamic Design, Selection, Application.
15060-3
15060-4
15060-5
foam inserts or other load bearing insulation should be used. The support should
include means for maintaining vapor barrier integrity. Because of the
temperature/compressive strength relationship of polyurethane foam, the
recommended shield designs must be selected to accommodate loading conditions
at both the installation and operating temperature.
(Extracted from ANSI/MSS-SP69, 2003, Page 10, Section 10 and 10.1 to 10.3,
inclusive, with permission of the publisher, the Manufacturers Standardization
Society.)
E. Recommended Minimum Rod Diameters for Single Rigid Rod Hangers: (Extracted from
ANSI/MSS-SP69, 2003, Page 9, Table 4, with permission of the publisher, the
Manufacturers Standardization Society.)
NOMINAL PIPE OR
TUBING SIZE
DIA.
In mm
in mm
1/4 (6)
3/8 (10)
1/2 (15)
3/4 (20)
1 (25)
1-1/4 (32)
1-1/2 (40)
2 (50)
2-1/2 (65)
3 (80)
3-1/2 (90)
4 (100)
5 (125)
6 (150)
8 (200)
10 (250)
12 (300)
14 (350)
16 (400)
18 (450)
20 (500)
24 (600)
30 (750)
3/8 M1O
3/8 M10
3/8 M1O
3/8 M1O
3/8 M1O
3/8 M1O
3/8 M10
1/2 M12
1/2 M12
1/2 M12
5/8 M16
5/8 M16
3/4 M20
3/4 M20
7/8 M20
7/8 M20
1 M24
1 M24
1 M24
1-1/4 M30
1-1/4 M30
15060-6
NOMINAL
ROD DIA.
in mm
3/8 M1O
3/8 M10
3/8 M1O
3/8 M10
3/8 M1O
3/8 M1O
3/8 M1O
318 M1O
1/2 M12
1/2 M12
1/2 M12
1/2 M12
1/2 M12
5/8 M16
3/4 M20
3/4 M20
3/4 M20
1-1/4 M30
1. (1) For calculated loads, rod diameters may be sized in accordance with MSS SP-58,
Table 3 provided Table 1 and Section 73 of MSS SP-58 are satisfied.
2. (2) Rods may be reduced one size for double rod hangers. Minimum rod diameter
shall be 3/8 inch (9.5 mm) (M10).
3. (3) Columns noted refer to Table 3.
F.
1.5 SUBMITTALS
15060-7
C. Certifications:
1. Product certificates signed by manufacturer certifying materials comply with specified
performance characteristics and criteria and physical requirements. Certificates shall
be furnished only as required by specific codes, upon request.
D. Shop Drawings:
1. Bases, hangers and supports.
2. Connections to equipment and structure.
3. Structural assemblies.
E. Selection Samples: For each finish product specified, two complete sets of color chips
representing manufacturer's full range of available colors and patterns.
F.
Verification Samples: For each finish product specified, two samples, minimum size 6
inches (150 mm) square, representing actual product, color, and patterns.
G. Closeout Submittals:
1. Warranty: Warranty documents.
2. Operation and Maintenance Data: Operation and maintenance data for installed
products in accordance with Division 1 Closeout Submittals (Maintenance Data and
Operation Data) Section. Include methods for maintaining installed products, and
precautions against cleaning materials and methods detrimental to finishes and
performance.
15060-8
A. Manufacturer Qualifications:
1. Manufacturing facilities shall be registered to ISO 9001.2000 and assessed to ISO
9000.2000 standard. A copy of the current certificate shall be available upon request.
B. Installer Qualifications:
1. Utilize an installer experienced in performing work of this section who is experienced
in installation of work similar to that required for this project and per the minimum
requirements of MSS SP-89.
B. Store and dispose of solvent-based materials, and materials used with solvent-based
materials, in accordance with requirements of local authorities having jurisdiction.
1.9 WARRANTY
15060-9
PART 2 PRODUCTS
2.1 MANUFACTURERS
A. Acceptable Manufacturer: Anvil Intl., Inc.; 110 Corporate Dr. Suite 10, Portsmouth, NH
03802. ASD. Tel: (000) (603) 422-8000. Fax: (603) 422-8033. Email: nwrightross@anvilintl.com. Web: http://www.anvilintl.com.
2.2 GENERAL
A. Fabricate hangers, supports and sway braces to comply with building codes.
B. Use components for intended service conditions only. Do not use installed hangers for
rigging or erection purposes.
A. Finishes:
1. Pipe Hangers and Supports: Galvanized after manufacture.
a.
b.
2. Pipe Hangers and Supports: Painted with zinc-rich paint after manufacture.
3. Pipe Hangers and Supports: Manufacturers standard primer that meets Fed Spec TTP-636 after manufacture.
15060-10
4. Ensure steel hangers in contact with copper piping are Copper plated, copper painted
or epoxy coated.
a.
B. Pipe Rings:
15060-11
1. Product: 104 Adjustable Swivel Ring, Split Ring Type. Complies with MSS-SP (Type
6).
2. Product: 108 Split Pipe Ring. Complies with MSS-SP (Type 11).
3. Product: 138R Extension Split Pipe Clamp (Rod Threaded). Complies with MSS-SP
(Type 12).
4. Product: 67 Pipe or Conduit Hanger. Complies with MSS-SP (Type 5).
5. Product: 69 Adjustable Swivel Ring, Tapped per NFPA Standards. Complies with
MSS-SP (Type 10).
6. Product: 97 Adjustable Pipe Ring. Complies with MSS-SP (Type 9).
7. Product: 97C Adjustable Pipe Ring (Plastic Coated). Complies with MSS-SP (Type 9).
8. Material: Malleable iron per ASTM A47/ASTM A126.
9. Material: Carbon steel per ASTM A36/ASTM A1011.
10. Size: Refer to drawing.
11. Finish: Plain.
12. Finish: Galvanized.
13. Maximum Temperature:
a.
b.
C. Clevis:
1. Product: 260 Adjustable Clevis Hanger. Complies with MSS-SP (Type 1).
2. Product: 300 Adjustable Clevis for Insulated Lines. Complies with MSS-SP (Type 1).
3. Product: 590 Adjustable Clevis for Ductile or Cast Iron Pipe. Complies with MSS-SP
(Type 1).
4. Product: 65 Light Duty Adjustable Clevis.
5. Material: Carbon steel per ASTM A36/ASTM A1011.
6. Size: Refer to drawing.
7. Finish: Plain.
8. Finish: Galvanized.
9. Finish: Epoxy.
15060-12
b.
c.
15060-13
b.
c.
d.
F.
Beam Clamps:
1. Product: 133 Standard Duty Beam Clamp. Complies with MSS-SP (Type 21).
2. Product: 134 Heavy Duty Beam Clamp. Complies with MSS-SP (Type 21).
3. Product: 14 Adjustable Side Beam Clamp. Complies with MSS-SP-69 (Type 27).
4. Product: 217 Adjustable Side Beam Clamp. Complies with MSS-SP-69 (Type 25).
5. Product: 218 Malleable Beam Clamp without Extension Piece. Complies with MSSSP-69 (Type 30).
6. Product: 227 Top Beam Clamp. Complies with MSS-SP-69 (Type 25).
7. Product: 228 Universal Forged Steel (UFS) Beam Clamp. Complies with MSS-SP-69
(Type 28 and 29).
8. Product: 292 Beam Clamp Right Hand Thread with Weld less Eye Nut. Complies with
MSS-SP-69 (Type 28 and 29).
9. Product: 292L Beam Clamp Left Hand Thread with Weld less Eye Nut. Complies with
MSS-SP-69 (Type 28 and 29).
15060-14
10. Product: 86 C-Clamp with Set Screw & Lock Nut. Complies with MSS-SP-69 (Type
23).
11. Product: 87 C-Clamp with Set Screw & Fig. 89 Retaining Clip. Complies with MSSSP-69 (Type 23).
12. Product: 88 C-Clamp with Set Screw Only. Complies with MSS-SP-69 (Type 23).
13. Product: 89 Retaining Clip.
14. Product: 89X Retaining Clip.
15. Product: 92 Universal C-type Clamp (Standard Throat). Complies with MSS-SP-69
(Type 19 and 23).
16. Product: 93 Universal C-type Clamp (Wide Throat). Complies with MSS-SP-69 (Type
19 and 23).
17. Product: 94 Wide Throat Top Beam C-Clamp. Complies with MSS-SP-69 (Type 19).
18. Product: 95 C-Clamp with Locknut. Complies with MSS-SP-69 (Type 23).
19. Material: Malleable iron per ASTM A47/ASTM A126.
20. Material: Carbon steel per ASTM A36.
21. Material: Ductile iron per ASTM A536.
22. Material: Forged steel per ASTM A668.
23. Size: Refer to drawing.
24. Finish: Plain.
25. Finish: Galvanized.
G. Structural Attachments:
1. Product: 112 Brace Fitting Complete.
2. Product: 113 Brace Fitting (Pipe End Only).
3. Product: 54 Two Hole Welding Beam Lug.
4. Product: 55 Structural Welding Lug (Short). Complies with MSS-SP-69 (Type 57).
5. Product: 55L Structural Welding Lug (Long). Complies with MSS-SP-69 (Type 57).
6. Product: 60 Steel Washer Plate.
7. Product: 66 Welded Beam Attachment. Complies with MSS-SP-69 (Type 22).
8. Material: Carbon steel per ASTM A36, ASTM A47, ASTM A126 and ASTM A515.
15060-15
I.
Brackets:
1. Product: 194 Light Welded Steel Bracket. Complies with MSS-SP-69 (Type 31).
1. Product: 195 Medium Welded Steel Bracket. Complies with MSS-SP-69 (Type 32).
2. Product: 199 Heavy Welded Steel Bracket. Complies with MSS-SP-69 (Type 33).
3. Product: 202 Iron Side Beam Bracket. Complies with MSS-SP-69 (Type 34).
4. Product: 206 Steel Side Beam Bracket. Complies with MSS-SP-69 (Type 34).
5. Product: 207 Threaded Steel Side Beam Bracket. Complies with MSS-SP-69 (Type
34).
6. Material: Malleable iron per ASTM A47/ASTM A126.
7. Material: Carbon steel per ASTM A36.
8. Size: Refer to drawing.
15060-16
9. Finish: Plain.
10. Finish: Galvanized.
11. Maximum Temperature:
J.
a.
b.
15060-17
5. Product: 248 Machine Threaded Rod with Eye End. Right-hand threads with unwelded eye.
6. Product: 248L Machine Threaded Rod with Eye End. Left-hand threads with unwelded eye.
7. Product: 248X Machine Threaded Rod with Linked Eye Ends. Un-welded eye.
8. Product: 253 Machine Threaded Rod. Threaded both ends with right-hand and lefthand threads.
9. Product: 278 Machine Threaded Rod with Eye End. Right-hand threads with welded
eye.
10. Product: 278L Machine Threaded Rod with Eye End. Left-hand threads with welded
eye.
11. Product: 278X Machine Threaded Rod with Linked Eye Ends. Welded eye.
12. Product: 110R Socket, Rod Threaded. Complies with MSS-SP-69 (Type 16).
13. Product: 114 Turnbuckle Adjuster. Complies with MSS-SP-69 (Type 15).
14. Product: 135 Straight Rod Coupling (With Sight-Hole).
15. Product: 135E Straight Rod Coupling (Less Sight-Hole).
16. Product: 135R Straight Rod Coupling (Reducing).
17. Product: 136 Straight Rod Coupling. Complies with MSS-SP-69 (Type 40).
18. Product: 136R Straight Rod Coupling (Reducing).
19. Product: 157 Extension piece.
20. Product: 230 Turnbuckle. Complies with MSS-SP-69 (Type 13).
21. Product: 233 Turnbuckle. Complies with MSS-SP-69 (Type 13).
22. Product: 290 Thread Weld less Eye Nut (Right Hand Threads). Complies with MSSSP-69 (Type 17).
23. Product: 290L Thread Weld less Eye Nut (Left Hand Threads). Complies with MSSSP-69 (Type 17).
24. Product: 299 Forged Steel Clevis. Complies with MSS-SP-69 (Type 14).
25. Material: Carbon steel per ASTM A36.
26. Material: Malleable iron per ASTM A47/A126.
27. Material: Forged steel per ASTM A668.
28. Size: Refer to drawing.
15060-18
b.
b.
M. Pipe Supports:
15060-19
1. Product: 191 Pipe Stanchion Saddle With U-Bolt. Complies with MSS-SP-69 (Type
37).
2. Product: 192 Adjustable Pipe Saddle Support. Complies with MSS-SP-69 (Type 38).
3. Product: 258 Pipe Saddle Support. Complies with MSS-SP-69 (Type 36).
4. Product: 259 Pipe Stanchion Saddle Support. Complies with MSS-SP-69 (Type 37).
5. Product: 264 Adjustable Pipe Saddle Support. Complies with MSS-SP-69 (Type 38).
6. Product: 265 Adjustable Pipe Saddle Support. Complies with MSS-SP-69 (Type 38).
7. Product: 62 Pipe Stanchion, Type A, B and C.
8. Product: 63 Pipe Stanchion, Type A, B and C.
9. Material: Carbon steel per ASTM A36/ASTM A53.
10. Material: Cast iron steel per ASTM A48.
11. Finish: Plain.
12. Finish: Galvanized.
13. Pipe Size: Refer to drawings.
14. Stanchion Size: Refer to drawings.
b.
15060-20
P.
Pipe Rolls:
1. Product: 171 Single Pipe Roll. Complies with MSS-SP-69 (Type 41).
2. Product: 175 Roller Chair. Complies with MSS-SP-69 (Type 44).
3. Product: 177 Adjustable Pipe Roll Support. Complies with MSS-SP-69 (Type 41).
4. Product: 178 Spring Cushion Hanger. Complies with MSS-SP-69 (Type 49).
5. Product: 181 Adjustable Steel Yoke Pipe Roll. Complies with MSS-SP-69 (Type 43).
15060-21
6. Product: 271 Complete Pipe Roll Stand. Complies with MSS-SP-69 (Type 44).
7. Product: 274 Adjustable Pipe Roll Stand With Base Plate. Complies with MSS-SP-69
(Type 46).
8. Product: 274P Adjustable Pipe Roll Stand, Base Plate Only.
9. Product: 275 Adjustable Pipe Roll Stand Without Base Plate.
10. Product: 277 Pipe Roll and Base Plate with Cast Iron Base Plate. Complies with MSSSP-69 (Type 45).
11. Product: 277S Pipe Roll and Base Plate with Steel Base Plate.
12. Material: Carbon steel per ASTM A36/ASTM A1011.
13. Material: Cast iron steel per ASTM A48.
14. Size and Dimension: Refer to drawing.
15. Finish: Plain.
16. Finish: Galvanized.
17. Maximum Temperature:
a.
b.
15060-22
b.
b.
c.
d.
15060-23
PART 3 EXECUTION
3.1 EXAMINATION
3.2 PREPARATION
B. Prepare surfaces using the methods recommended by the manufacturer for achieving the
best result for the substrate under the project conditions.
15060-24
C. Gas and Fuel Oil Piping: Comply with pipe manufacturers recommendations and
applicable codes.
D. Copper Piping: Comply with pipe manufacturers recommendations and applicable codes.
E. Flexible Joint Roll Groove Pipe: Not less than one hanger at joints. For size and spacing
of hangers and supports, refer to manufacturers literature.
F.
Within 12 inches (305 mm) of each elbow and directly after change in direction of pipe.
C. Clevis Plates:
1. Attach to concrete with [4] minimum concrete inserts, [One] at each corner.
2. Provide supplementary structural steelwork where structural bearings do not exist or
where concrete inserts are not in correct locations.
15060-25
F.
H. Support from Structural Members: Where structural bearing does not exist or inserts are
not in suitable locations, provide supplementary structural steel members.
I.
Field welding of supports should be done by qualified welders using qualified welding
procedures.
J.
Proper care and ventilation should be given when welding galvanized components.
A. Angularity of rod hanger resulting from horizontal movement of pipework from cold to hot
position not to exceed 4 degrees from vertical.
B. Where horizontal pipe movement is greater than 1/2 inch (12.7 mm), offset pipe hanger
and support so that rod hanger is vertical in hot position.
15060-26
B. Adjustable Clevis:
1. Tighten hanger load nut securely to ensure proper hanger performance.
2. Tighten upper nut after adjustment.
C. C-Clamps:
1. Follow manufacturers recommended written instructions and torque values when
tightening C-clamps to bottom flange of beam.
D. Beam Clamps:
1. Tighten all set screws and lock nuts.
2. Hammer jaw firmly against underside of beam for Figure 127 only.
3.7 PROTECTION
END OF SECTION
15060-27