You are on page 1of 238

NATIONAL INSTITUTE FOR AVIATION RESEARCH

Wichita State University


CAM-RP-2009-015 April 22, 2011 Revision A

Hexcel 8552 IM7 Unidirectional


Prepreg 190 gsm & 35%RC
Qualification Material Property Data Report
FAA Special Project Number SP4614WI-Q
NCAMP Test Report Number: CAM-RP-2009-015 Rev A
April 22, 2011
Prepared by:
Kristin Marlett
Reviewed by:
Yeow Ng and John Tomblin
Approved By: Ed Hooper (FAA DER)
Accepted By: Wichita FAA ACO Office (pending)

NATIONAL INSTITUTE FOR AVIATION RESEARCH

Wichita State University


CAM-RP-2009-015 April 22, 2011 Revision A

Testing Facility:
National Institute for Aviation Research
Wichita State University
1845 N. Fairmount
Wichita, KS 67260-0093

REVISIONS:
Rev
A

By
Kristin Marlett

N/C

Kristin Marlett

N/C
N/C

Kristin Marlett
Kristin Marlett

N/C

Kristin Marlett

N/C
N/C
N/C

Kristin Marlett
Kristin Marlett
Kristin Marlett

N/C

Kristin Marlett

N/C

Kristin Marlett

N/C
N/C

Kristin Marlett
Kristin Marlett

N/C

Kristin Marlett

Date
Rev App By Pages Revised or Added
4/22/2011 Yeow Ng
UNT1-B-C2 data removed due to unbalanced
layup
4/14/2011 Yeow Ng
ILT values updated. Test Summary for LT
updated. Test Chart for IPS updated and TC
and UNC3 Modulus plots in Raw Data section
updated.
5/10/2010 Yeow Ng
UNTO back-out calculations revised
6/10/2010 Yeow Ng
several formatting changes. The following test
methods had specimens removed: IPS 0.2%
offset (RTD); UNT2 (CTD), OHC2 (RTD),
UNT0 (RTD, ETW), TC (ETW)
6/15/2010 Yeow Ng
UNTO back-out calculations revised (RTD)
and additional justifications provided for
normalization
7/1/2010 Yeow Ng
Minor formatting changes
7/6/2010 Yeow Ng
worst case environments changed on FSBS
8/2/2010 Yeow Ng
stress strain curve modified and introduction
edited (material spec release date and process
spec cure cycle).
8/18/2010 Yeow Ng
FSBS chart edited to change the worst case
environment values
8/30/2010 Yeow Ng
IPS RTD values changed due to extensometer
slippage
9/27/2010 Yeow Ng
FSBS chart title edited
10/18/2010 Yeow Ng
Ultimate Strength & Modulus removed for all
SSB1,2,3 conditions
11/17/2010 Yeow Ng
Minor lamina chart template changed and IPS
conditioning chart modified

CAM-RP-2009-015 April 22, 2011 Revision A


TABLE OF CONTENTS
1.

Introduction ................................................................................................... 8
1.1
Scope .................................................................................................................................................................. 8
1.2
Symbols Used ................................................................................................................................................... 10
Acronyms and Definitions ............................................................................................................................................ 11
1.3
NIAR Hexcel Specimen Naming Format ......................................................................................................... 12
1.4
References........................................................................................................................................................ 13
1.5
Methodology ..................................................................................................................................................... 14
1.5.1
Process Definition ...................................................................................................................................... 14
1.5.2
Specimen & Testing Details ....................................................................................................................... 17
1.5.2.1 Tabbing .................................................................................................................................................. 17
1.5.2.2 Specimen Dimensions & Test Configuration .......................................................................................... 17
1.5.3
Test Matrix ................................................................................................................................................. 18
1.5.4
Physical Testing......................................................................................................................................... 23
1.5.5
Environmental Conditioning ....................................................................................................................... 24
1.5.6
Non-ambient Testing.................................................................................................................................. 26
1.5.7
Fluid Sensitivity Screening ......................................................................................................................... 27
1.5.8
Normalization Procedures.......................................................................................................................... 30
1.5.9
Conformity ................................................................................................................................................. 31
1.5.10 Material Pedigree Information .................................................................................................................... 31
2. Test Results ................................................................................................ 33
2.1
Lamina Level Test Summary ............................................................................................................................ 33
2.2
Laminate Level Test Summary ......................................................................................................................... 34
2.3
Individual Test Summaries ................................................................................................................................ 35
2.3.1
Longitudinal Tension Properties ................................................................................................................ 35
2.3.2
Transverse Tension Properties .................................................................................................................. 36
2.3.3
Longitudinal Compression Properties ........................................................................................................ 37
2.3.4
Transverse Compression Properties ......................................................................................................... 38
2.3.5
In-Plane Shear Properties.......................................................................................................................... 39
2.3.6
Unnotched Compression 0 Properties ....................................................................................................... 40
2.3.7
Unnotched Tension 0 Properties ............................................................................................................... 41
2.3.8
Short Beam Strength Properties ................................................................................................................ 42

Page 3 of 238

CAM-RP-2009-015 April 22, 2011 Revision A


2.3.9
Unnotched Tension 1 Properties ............................................................................................................... 43
2.3.10 Unnotched Tension 2 Properties ............................................................................................................... 44
2.3.11 Unnotched Tension 3 Properties ............................................................................................................... 45
2.3.12 Unnotched Compression 1 Properties ....................................................................................................... 46
2.3.13 Unnotched Compression 2 Properties ....................................................................................................... 47
2.3.14 Unnotched Compression 3 Properties ....................................................................................................... 48
2.3.15 Laminate Short Beam Strength Properties ................................................................................................ 49
2.3.16 Open Hole Tension 1 Properties................................................................................................................ 50
2.3.17 Open Hole Tension 2 Properties................................................................................................................ 51
2.3.18 Open Hole Tension 3 Properties................................................................................................................ 52
2.3.19 Filled-Hole Tension 1 Properties................................................................................................................ 53
2.3.20 Filled-Hole Tension 2 Properties................................................................................................................ 54
2.3.21 Filled-Hole Tension 3 Properties................................................................................................................ 55
2.3.22 Open Hole Compression 1 Properties ....................................................................................................... 56
2.3.23 Open Hole Compression 2 Properties ....................................................................................................... 57
2.3.24 Open Hole Compression 3 Properties ....................................................................................................... 58
2.3.25 Filled-Hole Compression 1 Properties ....................................................................................................... 59
2.3.26 Filled-Hole Compression 2 Properties ....................................................................................................... 60
2.3.27 Filled-Hole Compression 3 Properties ....................................................................................................... 61
2.3.28 Single Shear Bearing 1 Properties............................................................................................................. 62
2.3.29 Single Shear Bearing 2 Properties............................................................................................................. 63
2.3.30 Single Shear Bearing 3 Properties............................................................................................................. 64
2.3.31 Compression after Impact Properties ........................................................................................................ 65
2.3.32 Interlaminar Tension Properties ................................................................................................................. 66
3. Individual Test Charts ................................................................................. 67
3.1
Longitudinal Tension Properties........................................................................................................................ 68
3.2
Transverse Tension Properties ......................................................................................................................... 69
3.3
Longitudinal Compression Properties ............................................................................................................... 70
3.4
Transverse Compression Properties................................................................................................................. 71
3.5
In-Plane Shear Properties ................................................................................................................................. 72
3.6
Unnotched Compression 0 Properties .............................................................................................................. 73
3.7
Unnotched Tension 0 Properties....................................................................................................................... 74
3.8
Lamina Short Beam Strength ............................................................................................................................ 75

Page 4 of 238

CAM-RP-2009-015 April 22, 2011 Revision A


3.9
Unnotched Tension 1 Properties....................................................................................................................... 76
3.10 Unnotched Tension 2 Properties....................................................................................................................... 77
3.11 Unnotched Tension 3 Properties....................................................................................................................... 78
3.12 Unnotched Compression 1 Properties .............................................................................................................. 79
3.13 Unnotched Compression 2 Properties .............................................................................................................. 80
3.14 Unnotched Compression 3 Properties .............................................................................................................. 81
3.15 Laminate Short Beam Shear Properties ........................................................................................................... 82
3.16 Open Hole Tension 1 Properties ....................................................................................................................... 83
3.17 Open Hole Tension 2 Properties ....................................................................................................................... 84
3.18 Open Hole Tension 3 Properties ....................................................................................................................... 85
3.19 Filled-Hole Tension 1 Properties ....................................................................................................................... 86
3.20 Filled-Hole Tension 2 Properties ....................................................................................................................... 87
3.21 Filled-Hole Tension 3 Properties ....................................................................................................................... 88
3.22 Open Hole Compression 1 Properties .............................................................................................................. 89
3.23 Open Hole Compression 2 Properties .............................................................................................................. 90
3.24 Open Hole Compression 3 Properties .............................................................................................................. 91
3.25 Filled-Hole Compression 1 Properties .............................................................................................................. 92
3.26 Filled-Hole Compression 2 Properties .............................................................................................................. 93
3.27 Filled-Hole Compression 3 Properties .............................................................................................................. 94
3.28 Single Shear Bearing Strength1 Properties ...................................................................................................... 95
3.29 Single Shear Bearing Strength 2 Properties ..................................................................................................... 95
3.30 Single Shear Bearing 3 Properties .................................................................................................................... 96
3.31 Compression Strength After Impact 1 Properties .............................................................................................. 97
3.32 Interlaminar Tension Properties ........................................................................................................................ 98
4. Raw Data .................................................................................................... 99
4.1
Longitudinal Tension Properties...................................................................................................................... 100
4.2
Transverse Tension Properties ....................................................................................................................... 106
4.3
Longitudinal Compression Properties ............................................................................................................. 112
4.4
Transverse Compression Properties............................................................................................................... 117
4.5
In-Plane Shear Properties ............................................................................................................................... 123
4.6
Unnotched Compression 0 Properties ............................................................................................................ 129
4.7
Unnotched Tension 0 Properties..................................................................................................................... 134
4.8
Unnotched Tension 1 Properties..................................................................................................................... 139

Page 5 of 238

CAM-RP-2009-015 April 22, 2011 Revision A


4.9
Unnotched Tension 2 Properties..................................................................................................................... 145
4.10 Unnotched Tension 3 Properties..................................................................................................................... 151
4.11 Unnotched Compression 1 Properties ............................................................................................................ 157
4.12 Unnotched Compression 2 Properties ............................................................................................................ 161
4.13 Unnotched Compression 3 Properties ............................................................................................................ 165
4.14 Laminate Short Beam Strength Properties ..................................................................................................... 169
4.15 Lamina Short Beam Strength Properties ........................................................................................................ 173
4.16 Open Hole Tension 1 Properties ..................................................................................................................... 179
4.17 Open Hole Tension 2 Properties ..................................................................................................................... 182
4.18 Open Hole Tension 3 Properties ..................................................................................................................... 185
4.19 Filled-Hole Tension 1 Properties ..................................................................................................................... 188
4.20 Filled-Hole Tension 2 Properties ..................................................................................................................... 191
4.21 Filled-Hole Tension 3 Properties ..................................................................................................................... 194
4.22 Open Hole Compression 1 Properties ............................................................................................................ 197
4.23 Open Hole Compression 2 Properties ............................................................................................................ 199
4.24 Open Hole Compression 3 Properties ............................................................................................................ 201
4.25 Filled-Hole Compression 1 Properties ............................................................................................................ 203
4.26 Filled-Hole Compression 2 Properties ............................................................................................................ 205
4.27 Filled-Hole Compression 3 Properties ............................................................................................................ 207
4.28 Single Shear Bearing 1 Properties .................................................................................................................. 209
4.29 Single Shear Bearing 2 Properties .................................................................................................................. 211
4.30 Single Shear Bearing 3 Properties .................................................................................................................. 213
4.31 Compression Strength After Impact 1 Properties ............................................................................................ 215
4.32 Interlaminar Tension Properties ...................................................................................................................... 216
5. Shear Stress vs. Shear Strain, RTD.......................................................... 219
6. FLUID SENSITIVITY COMPARISON ....................................................... 220
7. MOISTURE CONDITIONING CHARTS .................................................... 228
7.1
In-Plane Shear Thinnest Panel ..................................................................................................................... 228
7.2
Short Beam Strength- Thickest Panel ............................................................................................................. 229
8. DMA Results ............................................................................................. 230
8.1
DMA Wet Batch A ........................................................................................................................................... 232
8.2
DMA Dry Batch A ............................................................................................................................................ 233
9. TMA Results.............................................................................................. 234

Page 6 of 238

CAM-RP-2009-015 April 22, 2011 Revision A


9.1
TMA Wet Batch A Results............................................................................................................................... 236
9.2
TMA Wet Batch A Results............................................................................................................................... 236
10. Physical Test Results ................................................................................ 237
11. Deviations ................................................................................................. 238

List of Tables
Table 1-1: Lamina Level Test Matrix ............................................................................................................................ 19
Table 1-2: Laminate Level Test Matrix ......................................................................................................................... 22
Table 1-3: Physical Testing Matrix ............................................................................................................................... 24
Table 1-4: Fluid Sensitivity Matrix................................................................................................................................ 29
Table 2-1: Lamina Summary Data ................................................................................................................................ 33
Table 2-2: Laminate Summary Data ............................................................................................................................. 34
Table 8-1: DMA Wet Results ....................................................................................................................................... 230
Table 8-2: DMA Dry Results ....................................................................................................................................... 231
Table 9-1: Wet TMA Results ....................................................................................................................................... 234
Table 9-2: Dry TMA Results ........................................................................................................................................ 235
Table 10-1: Hexcel Physical Testing Results ............................................................................................................ 237
List of Figures
Figure 1-1: Specimen Selection Methodology ............................................................................................................ 14
Figure 1-2: Specimen Traceability Line ....................................................................................................................... 15

Page 7 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

1. Introduction
1.1 Scope
The test methods and results described in this document are intended to provide basic composite properties essential to
most methods of analysis and are consistent with MIL-HDBK-17-1FComposite Materials Handbook for Polymer
Matrix Composites. This report contains material property data of common usefulness to wide range of projects. The
lamina and laminate material property data have been generated with FAA oversight through FAA Special Project
Number SP4652WI-Q and also meet the requirements of NCAMP Standard Operating Procedure NSP 100; the test
panels, test specimens, and test setups have been conformed by the FAA and the testing has been witnessed by the
FAA. However, the data may not fulfill all the needs of any specific company's programs; specific properties,
environments, laminate architecture, and loading situations may require additional testing.
The use of NCAMP material and process specifications do not guarantee material or structural performance. Material
users should be actively involved in evaluating material performance and quality including, but not limited to, performing
regular purchaser quality control tests, performing periodic equivalency/additional testing, participating in material
change management activities, conducting statistical process control, and conducting regular supplier audits.
The applicability of NCAMP material property data, material allowables, and specifications must be evaluated on caseby-case basis by aircraft companies and certifying agencies. NCAMP assumes no liability whatsoever, expressed or
implied, related to the use of the material property data, material allowables, and specifications.
This report contains material property data only. Statistical analysis of the data including the calculations of b-basis
values is given in a separate report, Hexcel IM7 Unidirectional Prepreg 190 gsm 35% RC Qualification Statistical
Analysis Report NCP-RP-2009-028 N/C. The qualification material was procured to NCAMP Material Specification
NMS 128/2 Rev - Initial Release dated February 6, 2007. The panels were fabricated by Cessna Aircraft Company,
5800 E Pawnee, Wichita, KS 67218. The qualification test panels were cured in accordance with Baseline Cure Cycle
(M) of NCAMP Process Specification NPS 81228 Rev A Initial Release June 7, 2007. The NCAMP Test Plan NTP
1828Q1 Rev B was used for this qualification program.
Part fabricators that wish to utilize the material property data, allowables, and specifications may be able to do so by
demonstrating the capability to reproduce the original material properties; a process known as equivalency. More
information about this equivalency process including the test statistics and its limitations can be found in Section 6 of

Page 8 of 238

CAM-RP-2009-015 April 22, 2011 Revision A


DOT/FAA/AR-03/19 and Section 8.4.1 of MIL-HDBK-17-1F. The applicability of equivalency process must be evaluated
on program-by-program basis by the applicant and certifying agency. The applicant and certifying agency must agree
that the equivalency test plan along with the equivalency process described in Section 6 of DOT/FAA/AR-03/19 and
Section 8.4.1 of MIL-HDBK-17-1F are adequate for the given program.
Aircraft companies should not use the data published in this report without specifying NCAMP Material Specification
NMS 128/2. NMS 128/2 have additional requirements that are listed in its prepreg process control document (PCD),
fiber specification, fiber PCD, and other raw material specifications and PCDs which impose essential quality controls
on the raw materials and raw material manufacturing equipment and processes. Aircraft companies and certifying
agencies should assume that the material property data published in this report is not applicable when the material is
not procured to NMS 128/2. NMS 128/2 is a free, publicly available, non-proprietary aerospace industry material
specification.
The data contained in this report is intended for general distribution to the public, either freely or at a price that does not
exceed the cost of reproduction (e.g. printing) and distribution (e.g. postage). Data that is subject to export control
regulations, if any, will be made available on a case by case basis through written request to NCAMP.

Page 9 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

1.2 Symbols Used


12t

E1c
E1t
E2c
E2t
F1cu
F1tu
F2cu
F2tu
SBS
12c
21c
F12s5% strain
F12s0.2%
G12s

major Poissons ratio, tension


micro-strain
compressive modulus, longitudinal / warp direction
tensile modulus, longitudinal / warp direction
compressive modulus, transverse / fill direction
tensile modulus, transverse / fill direction
ultimate compressive strength, longitudinal / warp direction
ultimate tensile strength, longitudinal / warp direction
ultimate compressive strength, transverse / fill direction
ultimate tensile strength, transverse / fill direction
short beam strength
major Poissons Ratio, compression
minor Poissons Ratio, compression
in-plane shear strength at 5% strain
in-plane shear strength at 0.2% offset
in-plane shear modulus

Superscripts
c
cu
s
su
t
tu

compression
compression ultimate
shear
shear ultimate
tension
tension ultimate

Subscripts
1 axis; longitudinal / warp direction
(parallel to warp direction of reinforcement)

Page 10 of 238

CAM-RP-2009-015 April 22, 2011 Revision A


2 axis; transverse / fill direction
(parallel to fill direction of reinforcement)
12;
in-plane

Acronyms and Definitions


ASTM
B Basis
CV
CTD
CPT
ETD
ETW
Gr/Ep
norm
RTD
SACMA
SRM
CPT
Tply
wet
T, RH

American Society for Testing and Materials


95% lower confidence limit on the tenth population percentile
Coefficient of variation
cold temperature dry
cured ply thickness
elevated temperature dry
elevated temperature wet
graphite/epoxy
normalized
room temperature dry
Suppliers of Advanced Composite Materials Association
SACMA Recommended Method
cured ply thickness
thickness divided by the number of plies provides the thickness average per specimen
specimen with an equilibrium moisture content
temperature, relative humidity

Page 11 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

1.3 NIAR Hexcel Specimen Naming Format


NIAR NCAMP HEXCEL SPECIMEN NAMING FORMAT
CODE

CODE
A
B
C
D

CURE CYCLE

P REP REG LOT #/ BATCH #

SUB-P ANEL #
SP ECIMEN #

1
2
5
6
8
9

CODE

M1
M2
AH1
AH2
AL1
AL2

HO
HT
HB
HE
HF
HG
HW
HU
HY
HJ
HL
HN
HP

COMPANY
Hexcel
ATK Space Systems
Bell Helicopter
Boeing Helicopters
Cessna Aircraft Company
General Atomics
Goodrich
Gulfstream Aerospace
Hawker Beechcraft
Israel Aircraft Industries
Lockheed Martin Aeronautics
Northrop Grumman
Spirit AeroSystems

CODE
P
I
U

MATERIAL SYSTEM
(H11) AS4 PW Fab P repreg 38%RC-1628
(H12) IM7 Uni P repreg 38% RC-1828
(H13) AS4 Uni P repreg 35% RC-1128Q1

CODE

TEST METHOD

RTD (7010 F)
CTD (-65F)
ETD (250F)
ETW (250F)
FSBS Fluid

(70F, 250F)
a,1
100 Low Lead
b,2
SAE AMS 2629
c,3
MIL-P RF-5606
d,4
MIL-P RF-83282
e,5
MIL-P RF-7808
f,6
MIL-P RF-23699
g,7
Salt Water
h,8
Skydrol LD-4
i,9
50% Water w/ 50% Skydrol
j,m
MEK washing fluid
k,n
P olypropylene Glycol Deicer
l,p
Isopropyl Alcohol Deicing
r,s
Distilled Water
A,C
Dry
t,D
85% Relative Humidity

H0PJA123A

CODE

CONDITIONING

CODE

TEST METHOD

J
U
L
Z
N

(WT) Warp Tension/ (LT) Longitudinal Tension (D3039)


(FT) Fill Tension/ (TT) Transverse Tension (D3039)
(WC) Warp Compression/ (LC) Longitudinal Compression (D6641)
(FC) Fill Compression/ (TC) Transverse Compression (D6641)
(IP S) In P lane Shear (D3518)

Q
q

(SBS) Short Beam Shear (D2344)


(SBS1) Laminate Short Beam Shear

A
B
C
W
X
Y
D
E
F
G
H
I

(UNT1) Un-notched Tension Layup 1 (D3039)


(UNT2) Un-notched Tension Layup 2 (D3039)
(UNT3) Un-notched Tension Layup 3 (D3039)
(UNC1) Un-notched Compression Layup 1 (D6641)
(UNC2) Un-notched Compression Layup 2 (D6641)
(UNC3) Un-notched Compression Layup 3 (D6641)
(OHT1) Open Hole Tension Layup 1 (D5766)
(OHT2) Open Hole Tension Layup 2 (D5766)
(OHT3) Open Hole Tension Layup 3 (D5766)
(OHC1) Open Hole Compression 1 (D6484)
(OHC2) Open Hole Compression 2 (D6484)
(OHC3) Open Hole Compression 3 (D6484)

1
2
3
P
R

(SSB1) Single Shear P in Bearing Layup 1 (D5961)


(SSB2) Single Shear P in Bearing Layup 2 (D5961)
(SSB3) Single Shear P in Bearing Layup 3 (D5961)
(UNT0) Un-notched Tension 0/90 (D3039)
(UNC0) Un-notched Compression 0/90 (D6641)

4
5
6
7
8
9

(FHT1) Filled Hole Tension Layup 1 (D6742)


(FHT2) Filled Hole Tension Layup 2 (D6742)
(FHT3) Filled Hole Tension Layup 3 (D6742)
(FHC1) Filled Hole Compression Layup 1 (D6484)
(FHC2) Filled Hole Compression Layup 2 (D6484)
(FHC3) Filled Hole Compression Layup 3 (D6484)

K
M
T
V

(CAI1) Compression After Impact Layup 1 (SRM-2R)


(ILT1) Interlaminar Tension Layup 1 (D6415)
(MOL) Material Operating Limit Short Beam Shear (D2344)
(MOLC) Material Operating Limit Open Hole Compression (D2344)

Page 12 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

1.4 References
ASTM Standards
All testing was in accordance with nationally recognized standards, methods and procedures. Specific mechanical
property test methods applicable to the test program in this document include:

ASTM D2344/D2344M-00e1 Standard Test Method for Short-Beam Strength of Polymer Matrix Composite
Materials and Their Laminates
ASTM D3039/D3039M-08 Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials
ASTM D3518/D3518M-94(2007) Standard Test Method for In-Plane Shear Response of Polymer Matrix
Composite Materials by Tensile Test of a 45 Laminate In-Plane Shear Strength and Modulus
ASTM D5766/D5766M-02a Standard Test Method for Open Hole Tensile Strength of Polymer Matrix
Composite Laminates
ASTM D5961/D5961M-08 Standard Test Method for Bearing Response of Polymer Matrix Composite
Laminates
ASTM D6415-06ae1 Standard Test Method for Measuring the Curved Beam Strength of a Fiber-Reinforced
Polymer-Matrix Composite
ASTM D6484/D6484M-04 Standard Test Method for Open-Hole Compressive Strength of Polymer Matrix
Composite Laminates
ASTM D6641/D6641M-01e1 Standard Test Method for Determining the Compressive Properties of Polymer
Matrix Composite Laminates Using a Combined Loading Compression (CLC) Test Fixture
ASTM D6742/D6742M-02 Standard Practice for Filled-Hole Tension and Compression Testing of Polymer
Matrix Composite Laminates
ASTM D7136/D7136M-07 Standard Test Method for Measuring the Damage Resistance of a Fiber-Reinforced
Polymer Matrix Composite to a Drop-Weight Impact Event
ASTM D7137/D7137M-05e1 Standard Test Method for Compressive Residual Strength Properties of Damaged
Polymer Matrix Composite Plates

Page 13 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

1.5 Methodology
1.5.1 Process Definition
For each combination of test, batch and condition, the specimens were selected from minimum two separate panels
cured separately as shown in Figure 1-1 unless otherwise specified.
TRACEABILITY
PER ENVIRONMENTAL CONDITION AND TEST METHOD

Material
Batch

BATCH 1

BATCH 2

BATCH 3

Panel
Manufacturing
& Independent
Cure Process

PANEL 1

PANEL 2

PANEL 3

PANEL 4

PANEL 5

PANEL 6

Number of
Specimens
Required per
Test Method &
Environment

3 spec.

3 spec.

3 spec.

3 spec.

3 spec.

3 spec.

18 SPECIMENS TOTAL

Figure 1-1: Specimen Selection Methodology


All panels were fabricated in accordance with NCAMP Process Specification NPS 81228 M Cure Cycle.
In order to facilitate individual specimen trace ability, individual specimen numbering and/or skewed lines were
written or drawn across each sub-panel as shown in Figure 1-2.

Page 14 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

Figure 1-2: Specimen Traceability Line

For the single shear bearing tests, the ASTM D5961 was used with one of the pairs of specimens replaced by a
steel fixture. The configuration is shown in Figure 1-3 below.

Page 15 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

Specimen

Extensometer shim same


thickness as specimen

Shim of similar stiffness and equal thickness to specimen. One


shim per panel. Shim is held in place with grip pressure only

Figure 1-3: Modified ASTM D5961 (Single Shear Bearing) Specimen and Loading Arrangement

Page 16 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

1.5.2 Specimen & Testing Details


1.5.2.1 Tabbing
Tabs were used on all Longitudinal Tension specimens.

1.5.2.2 Specimen Dimensions & Test Configuration


For filled-hole and bearing tests, the hole diameter was 0.25 in -0.000 +0.003 in. For filled-hole tension tests, the
fasteners were installed to 855 in-lb. For filled-hole compression and bearing tests, the fasteners were installed to
305 in-lb. Fasteners were installed after moisture conditioning.
Unless otherwise specified, a tolerance of 5F applied to all temperature conditions specified in this document.
For filled-hole and bearing tests, the hole diameter was 0.25 in -0.000 +0.003 in. The following fasteners were used:
1) NASM 21297-04003 bolts with MS 21084 nuts and MS21206 washers for FHT and FHC
2) NASM 21297-04013 bolts with MS 21084 nuts and MS21206 washers for SSB

Page 17 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

1.5.3 Test Matrix


The tables below show the lay-ups and test matrices used for lamina and laminate level testing.

Layup

[0]6

Test Type and Direction

ASTM D3039 0
Tension

Property

Strength,
Modulus and
Poissons Ratio

Number of Batches x No. of


Panels x No. of Specimens
Test Temperature/Moisture
Condition
CTD
RTD
ETD ETW
3x2x3

3x2x3

3x2x3

ASTM D6641 0
Modulus
3x2x3 3x2x3 3x2x3 3x2x3
Compression (Note 1)
ASTM D3039 90
Strength and
[90]11
3x2x3 3x2x3
3x2x3
Tension
Modulus
ASTM D6641 90
Strength and
[90]14
3x2x3 3x2x3
3x2x3
Compression (Note 1)
Modulus
ASTM D3039 0
Strength and
[0/90]2S
3x2x3 3x2x3
3x2x3
Tension (see Note 2)
Modulus
ASTM D6641 0
Strength and
[90/0/90]5 Compression (see Note 1
3x2x3 3x2x3 3x2x3 3x2x3
Modulus
& 2)
ASTM D3518 In-Plane
Strength and
[45/-45]3S
3x2x3 3x2x3
3x2x3
Shear
Modulus
ASTM D2344 Short
[0]34
Strength
3x2x3 3x2x3 3x2x3 3x2x3
Beam
Note 1: Back-to-back strain gages are needed on the first two specimens of each environment. If no buckling is observed, the
remaining modulus specimens will require a strain gage on one side of the specimens only. An appropriate extensometer may
be used in place of strain gage.
Note 2: Derive the 0 lamina tensile or compressive strength Fu0  plies as follows
[0]14

Page 18 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

u
0  plies

P
= BF

wh
2

BF =

E1 [V 0 E 2 + (1 V 0) E1] ( 12 E 2 )

[V E + (1 V ) E ] [V
0

E 2 + (1 V 0) E1] ( 12 E 2 )

Where BF = Back-out factor obtained using linear classical lamination theory


Pf = Peak load carried by the test specimen (usually at failure)
w = specimen gage width, mm [in.]
h = specimen gage thickness, mm [in.]
V0 = fraction of 0 plies in the cross-ply laminate (1/2 for [0/90]ns and 1/3 for
[90/0/90]n)
E1 = axial tensile or compressive stiffness of 0 plies, from an average of all batches
E2 = transverse tensile or compressive stiffness of 0 plies, from an average of all
batches
12 = major Poissons ratio of 0 plies, from an average of all batches
Table 1-1: Lamina Level Test Matrix

Table 1-2 below summarizes the laminate level tests carried out. The layup angles 0, 45, -45, and 90 refer to the
orientation of the warp/longitudinal fiber direction. The laminate stacking sequences in this program are not specific to
any design. Therefore, careful consideration should be given to the validity of properties derived from this program
based on the design specific laminates in a structure to be certified.

Page 19 of 238

CAM-RP-2009-015 April 22, 2011 Revision A


Table 1-2 also emphasizes those properties and test condition combinations believed to constitute the worst case,
which in general is cold dry for tension and hot wet for compression and other matrix dominated properties.

Page 20 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

(%0/%45/%90)
Actual Test Type

(25/50/25 - QI)
UNT1
(10/80/10)
UNT2
(50/40/10)
UNT3
(25/50/25 - QI)
UNC1
(10/80/10)
UNC2
(50/40/10)
UNC3
(25/50/25 - QI)
SBS1
(25/50/25 - QI)
OHT1
(10/80/10)
OHT2
(50/40/10)
OHT3
(25/50/25 - QI)
FHT1
(10/80/10)
FHT2
(50/40/10)
FHT3
(25/50/25 - QI)
OHC1
(10/80/10)
OHC2
(50/40/10)
OHC3
(25/50/25 - QI)
FHC1

Test Type and Layup (5)

ASTM D3039 Un-notched Tension


[45/0/-45/90]2S
ASTM D3039 Un-notched Tension
[45/-45/0/45/-45/90/45/-45/45/-45]S
ASTM D3039 Un-notched Tension
[0/45/0/90/0/-45/0/45/0/-45]S
ASTM D6641 Un-notched Compression (4)
[45/0/-45/90]2S
ASTM D6641 Un-notched Compression (4)
[45/-45/0/45/-45/90/45/-45/45/-45]S
ASTM D6641 Un-notched Compression (4)
[45/0/90/0/-45/0/45/0/-45/0]S
ASTM D2344 Short Beam
(specimens may be taken from panels
designed for (25/50/25 - QI) CAI1)
ASTM D5766 Open Hole Tension (1)
[45/0/-45/90]2S
ASTM D5766 Open Hole Tension (1)
[45/-45/0/45/-45/90/45/-45/45/-45]S
ASTM D5766 Open Hole Tension (1)
[0/45/0/90/0/-45/0/45/0/-45]S
ASTM D6742 Filled Hole Tension (2)
[45/0/-45/90]2S
ASTM D6742 Filled Hole Tension (2)
[45/-45/0/45/-45/90/45/-45/45/-45]S
ASTM D6742 Filled Hole Tension (2)
[0/45/0/90/0/-45/0/45/0/-45]S
ASTM D6484 Open Hole Compression (1)(4)
[45/0/-45/90]3S
ASTM D6484 Open Hole Compression (1)(4)
[45/-45/0/45/-45/90/45/-45/45/-45]S
ASTM D6484 Open Hole Compression (1)(4)
[0/45/0/90/0/-45/0/45/0/-45]S
ASTM D6484 Filled Hole Compression (2)
[45/0/-45/90]3S

Page 21 of 238

Property

Strength &
modulus
Strength &
modulus
Strength &
modulus
Strength &
modulus
Strength &
modulus
Strength &
modulus

Number of Batches x Number of


Panels x Number of Test
Specimens
Test Temperature/Moisture
Condition
CTD
RTD
ETW
3x2x3

3x2x3

3x2x3

3x2x3

3x2x3

3x2x3

3x2x3

3x2x3

3x2x3

3x2x3

3x2x3

3x2x3

3x2x3

3x2x3

3x2x3

3x2x3

3x2x3

Strength
Strength

3x2x3

3x2x3

3x2x3

Strength

3x2x3

3x2x3

3x2x3

Strength

3x2x3

3x2x3

3x2x3

Strength

3x2x3

3x2x3

3x2x3

Strength

3x2x3

3x2x3

3x2x3

Strength

3x2x3

3x2x3

3x2x3

Strength

3x2x3

3x2x3

Strength

3x2x3

3x2x3

Strength

3x2x3

3x2x3

Strength

3x2x3

3x2x3

CAM-RP-2009-015 April 22, 2011 Revision A


(10/80/10)
FHC2
(50/40/10)
FHC3
(25/50/25 - QI)
SSB1
(10/80/10)
SSB2
(50/40/10)
SSB3
(100/0/0)
ILT
(25/50/25 - QI)
CAI1

ASTM D6484 Filled Hole Compression (2)


[45/-45/0/45/-45/90/45/-45/45/-45]S
ASTM D6484 Filled Hole Compression (2)
[0/45/0/90/0/-45/0/45/0/-45]S
ASTM D5961 Single Shear Bearing (3) (6)
[45/0/-45/90]2S
ASTM D5961 Single Shear Bearing (3) (6)
[45/-45/0/45/-45/90/45/-45/45/-45]S
ASTM D5961 Single Shear Bearing (3) (6)
[0/45/0/90/0/-45/0/45/0/-45]S
ASTM D6415 Interlaminar Tension
[0]22
ASTM D7136 & D7137 Compression After
Impact (1500 in.lb/in) (4)
[45/0/-45/90]3S

Strength

3x2x3

3x2x3

Strength

3x2x3

3x2x3

3x2x3

3x2x3

3x2x3

3x2x3

3x2x3

3x2x3

1x1x6

1x1x6

Strength &
Deformation
Strength &
Deformation
Strength &
Deformation
Strength
Strength

1x1x6

1x1x6

(1) Open-hole configuration: 0.25 hole diameter, 1.5 inch width.


(2) Filled-hole test configuration: 0.25 diameter, see section 2 for fastener callout, 1.5 width.
(3) Single shear bearing test configuration: 0.25: hole diameter, 1.5 width, see section 2 for fastener callout, e/D=3
(4) Back-to-back strain gages needed on the first two specimens of each environment. If no buckling is observed, the remaining modulus specimens will require strain gage on
one side of the specimens only. Appropriate extensometer may be used in place of the strain gage.
(5) Loading direction is generally along the 0-degree direction
(6) Use modified ASTM D5961 per Figure 3

(Note that the layup numbers 1, 2 and 3 correspond to those designated as quasi isotropic, soft and hard
respectively. In addition, the 0/90 cross-plied laminates used for the unidirectional materials only are designated
Layup 0).
Table 1-2: Laminate Level Test Matrix

Page 22 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

1.5.4 Physical Testing


The properties in Table 1-3 were determined for each panel used for test coupons with the exception of Tg by DMA
which were conducted on one laminate per batch from each oven cure conducted where that batch is present. The tests
were performed by the National Institute for Aviation Research (NIAR) Composites Laboratory under the supervision of
NCAMP.
Property

Condition/Method (Note 1)

Cured Ply Thickness

ASTM D3171-06

Laminate Density
Fiber Volume, % by Volume
Resin Content, % by Weight
Ultrasonic Through
Transmission, C-Scan
Glass Transition Temperature,
Tg by DMA
Glass Transition Temperature,
Tg by TMA

ASTM D792-00
ASTM D3171-06(Note 2)
ASTM D3171-06(Note 2)
MIL-HDBK-787A (Note 3)
Dry and Wet SACMA SRM
18R-94
Dry and Wet - HSP-T2 Rev 1
(by TMA)(Note 5)

Page 23 of 238

Min Replicates per


panel
All data from
mechanical test
specimens
3
3
3
1
1 Dry, 1 Wet (Note
4)
1 Dry, 1 Wet (Note
4)

CAM-RP-2009-015 April 22, 2011 Revision A


Notes 1: Where the applicable standard allows variations in specimen form or test method,
the specific parameters to be used will be specified in the test work instructions
and reported in the final test report.
2: Method II, except for laminates of materials where actual fiber weight is not
accurately known prior to impregnation, as in the case for unidirectional materials.
For these materials, in order to verify Method II is accurate, a minimum of 12
samples per batch shall be tested by Method I, Procedure B.
3: Five MHz is preferred for solid laminates. Panels with anomaly should be
segregated. Microscopy images may be taken from questionable areas. NCAMP
must be involved in the review of all C-scans.
4: Minimum total of 24 dry and 24 wet for each material system.
5: HSP-T2 Revision 1 is a Hexcel non-proprietary test method standard which may
be obtained from NCAMP. HSP-T2 is similar but not equivalent to ASTM
E2092.
Table 1-3: Physical Testing Matrix

1.5.5 Environmental Conditioning


The following tests were performed by the NIAR Composites Laboratory under the supervision of NCAMP.
Test environments are defined as:
CTD = -655F, dry
RTD = 7010F, room temperature dry
ETD = 2505F, dry
ETW = 2505F, wet (equilibrium moisture content)
Within each test method and test environment, the failure mode was evaluated immediately after each test by an
FAA DER. All tested specimens were digitally photographed after each test in order to pictorially document failure
modes. Representative photos are included in the CD accompanying this report.
For dry testing, specimens were dried at 160F5F for 120 to 130 hours. After drying, specimens were kept in a
desiccator until mechanical testing. Alternatively, the specimens may have been left ambient laboratory condition for
a maximum of 14 days until mechanical testing (no drying was required if specimens were tested within 14 days
Page 24 of 238

CAM-RP-2009-015 April 22, 2011 Revision A


from the date they were cured). Ambient laboratory condition is defined as 70F10F. Since moisture absorption
and desorption rate for epoxy is very slow at ambient temperature, there was no requirement to maintain relative
humidity levels.
For wet conditioning, specimens were dried at 160F5F for 120 to 130 hours before being conditioned to
equilibrium at 160F5F and 85% 5%. Effective moisture equilibrium was achieved when the average moisture
content of the traveler specimen changed by less than 0.05% for three consecutive readings which are 7 0.5 days
apart and may be expressed by:

W i -W i - 1
< 0.0005
Wb
where: Wi
= weight at current time
Wi 1 = weight at previous time
= baseline weight prior to conditioning
Wb
When representative specimens could not be measured to determine the moisture content (due to size, fastener and
tab effects), traveler coupons of at least 1 by 1 by specimen thickness and weighing at least 5 grams were used to
establish weight gain measurements. If the specimens or traveler coupons pass the criteria for three consecutive
readings which are 7 0.5 days apart, the specimens were kept in the environmental chamber for up to an additional
60 days. Alternatively, the specimens may have been removed from the environmental chamber and placed in a
sealed plastic bag along with a moist cotton towel for a maximum of 14 days until mechanical testing. Strain-gauged
specimens were removed from the controlled environment for a maximum of 2 hours for application of gages in
ambient laboratory conditions.

Page 25 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

1.5.6 Non-ambient Testing


The chamber was of adequate size so that all test fixtures and load frame grips were contained within the chamber.
For elevated temperature testing, the temperature chamber, test fixture, and grips were preheated to the specified
temperature. Each specimen was heated to the required test temperature as verified by a thermocouple in direct
contact with and taped to the specimen gage section. The heat-up time of the specimen did not exceed 5 minutes,
2 +1
unless otherwise specified in individual test summary sheets. The test was started 0 minutes after the specimen
reached the test temperature. During the test, the temperature, as measured on the specimen, was within 5F of the
required test temperature.
For subzero temperature testing, each specimen was cooled to the required test temperature as verified by a
+1
thermocouple in direct contact with and taped to the specimen gage section. The test started 5 0 minutes after the
specimen reached the test temperature. During the test, the temperature, as measured on the specimen, was within
5F of the required test temperature.

Page 26 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

1.5.7 Fluid Sensitivity Screening


Table 1-4 lists the requirements for fluid sensitivity screening, which requires ASTM D2344 Short Beam Strength testing
on [0]34 lamina level specimens dried at 160F5F for 120 to 130 hours before being subjected to the conditions
indicated, five replicates per fluid and one cure cycle. Specimens were cleaned with a dry towel prior to the tests. In
addition to short beam strength, load versus displacement curves were plotted to aid in the identification of matrix/resin
softening. Since load versus displacement curves are influenced by test machine and fixture compliance, all the tests
were performed with the identical machine and fixture, through a single setup. Experience suggests that for the vast
majority of epoxy resins, water is the fluid with the most deleterious effect on properties. Should screening tests for fluid
sensitivity indicate this to be the case, further testing of this type might be unnecessary since exposure to water
moisture to equilibrium level is an inherent part of the multi batch allowables test program. However, users must
evaluate the applicability of the exposure conditions and time on case-by-case basis. For example, the exposure
condition for jet fuel may not fully represent the condition of integral fuel tanks.

Page 27 of 238

CAM-RP-2009-015 April 22, 2011 Revision A


Extended Contact:
100 Low Lead Aviation Fuel
SAE AMS 2629 Jet Reference Fluid
MIL-PRF-5606 Hydraulic Oil
MIL-PRF-83282 Hydraulic Oil
MIL-PRF-7808 Engine Oil
MIL-PRF-23699, Class STD
Engine Oil
Salt Water
Skydrol LD-4
(SAE AS1241, Type IV, Class 1)
50% Water with 50% Skydrol LD-4
(SAE AS1241, Type IV, Class 1)

Test
Condition
70F
250F
70F
250F
70F
250F
70F
250F
70F
250F
70F
250F
70F
250F
70F
250F
70F

FS11RT
FS11ET
FS12RT
FS12ET
FS13RT
FS13ET
FS14RT
FS14ET
FS15RT
FS15ET
FS16RT
FS16ET
FS17RT
FS17ET
FS18RT
FS18ET
FS19RT

250F

FS19ET

90 minutes min. @ 70F10F


90 minutes min. @ 70F10F
90 minutes min. @ 70F10F
90 minutes min. @ 70F10F
484 hours @70F10F
484 hours @70F10F

70F
250F
70F
250F
70F
250F

FS21RT
FS21ET
FS22RT
FS22ET
FS23RT
FS23ET

90 days min. at 70F10F


90 days min. at 70F10F

70F
250F

FS31RT
FS31ET

Exposure
90 days min. @ 70F10F
90 days min. @ 70F10F
90 days min. @ 70F10F
90 days min. @ 70F10F
90 days min. @ 70F10F
90 days min. @ 70F10F
90 days min. @ 70F10F
90 days min. @ 70F10F
90 days min. @ 70F10F
90 days min. @ 70F10F
90 days min. @ 70F10F
90 days min. @ 70F10F
90 days min. @ 70F10F
90 days min. @ 70F10F
90 days min. @ 70F10F
90 days min. @ 70F10F
90 days min. @ 70F10F
90 days min. @ 70F10F

Code

Short Duration Contact:


MEK washing fluid. ASTM D740
Polypropylene Glycol Deicer
(Type I) Mil-A-824 3
Isopropyl Alcohol Deicing Agent
(TT-I-735)
Control Tests:
Distilled Water

Page 28 of 238

CAM-RP-2009-015 April 22, 2011 Revision A


Dry
85% Relative Humidity

Dry per section 6.1


Dry per section 6.1
Per section 6.1
Per section 6.1
Table 1-4: Fluid Sensitivity Matrix

Page 29 of 238

70F
250F
70F
250F

FS32RT
FS32ET
FS33RT
FS33ET

CAM-RP-2009-015 April 22, 2011 Revision A

1.5.8 Normalization Procedures


Most lamina level tension and compression strength and modulus properties, and all laminate level properties were
normalized according to nominal cured ply thickness. Lamina level properties that were not normalized include 90
tensile strength and modulus (unidirectional only), 90 compressive strength and modulus (unidirectional only), in-plane
shear strength and modulus, Poissons ratio, SBS, and ILT. After normalizing, data scatter reduced or remained the
same. If data scatter increased significantly after normalizing, the reason was investigated. Wherever properties are
normalized, both measured and normalized data were reported.
For unidirectional materials the fiber areal weight cannot be measured in advance of impregnation, hence Method I of
ASTM D3171, utilizing acid digestion, will be used to verify the CPT method in accordance with note (2) of Table 1-3.
Method I Fiber Volume (%vol) is 58.535 and Method 2 Fiber Volume (%vol) is 59.405. By comparing Fiber Volume
values obtained from Method I and Method II, the values are deemed close enough therefore the FAW is close to the
nominal of ~190 gsm. Based on the FAW data from Hexcel (Avg ~190 gsm) and our Method I Phys test data (Avg. void
content ~ 0% except for a panel where it is close to 4%) it is appropriate to use the CPT Method for normalization.
The average cured ply thickness of 0.0072 inch has been used as the nominal cured ply thickness (CPT) for
normalization purpose. The following normalization formula was used:
Normalized Value = Measured Value x Measured CPT / Nominal CPT.
Prior to beginning the qualification program, we predicted the cured ply thickness value to be 0.0074 inch. However, the
as-measured cured ply thickness of the qualification and the equivalency panels are 0.007174 inch and 0.007293 inch,
respectively (please review the attached file for cured ply thickness calculation). The grand average of all qualification
and equivalency panel thickness is 0.007229 inch. A vote was taken among the material users, and 3 out of the four
participating companies agreed that 0.0072 was an acceptable CPT. Not all companies cast a vote.

Page 30 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

1.5.9 Conformity
The 3-batch qualification panels have been fabricated according to the requirements of the test plan and conformed by
the FAA. The test specimens and test setups have also been conformed by the FAA.
Testing was witnessed by the FAA. Witnessing was delegated to a DER. Mechanical testing was carried out at the
National Institute for Aviation Research, Wichita State University. The test setup and procedures were reviewed by
NCAMP IAB and NCAMP staff during a facility audit. FAA conformity inspection records and approvals are included in
the CD accompanying this report.

1.5.10

Material Pedigree Information

The PMC Data Collection Template includes the material pedigree information required, such as material and batch
information, as well as panel fabrication record, environmental conditioning, test equipment, and test procedures. This
template in Microsoft Excel file format is included on the CD provided with this report.

Page 31 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

2. Test Results
2.1 Lamina Level Test Summary
Prepreg Material:

Hexcel Corporation - Hexcel 8552 IM7 Unidirectional


NMS 128/2 Material Specification
IM7 unidirectional

Resin

Hexcel 8552

Tg(dry)

406.43 F

Tg(wet)

321.41 F

PROCESSING:

NPS 81228 "M" Cure Cycle

Fiber

Date
Date
Date
Date

of fiber manufacture
of resin manufacture
of prepreg manufacture
of composite manufacture

Hexcel 8552 IM7


Unidirectional Tape
Lamina Properties Summary

Tg METHOD DMA (SRM 18-94)

Lot 1
Lot 2
01/26/2007
12/25/2006
02/28/2007
01/24/2007
02/28/2007
01/24/2007
9/2007 to 10/2007

Lot 3
02/05/2007
03/01/2007
03/01/2007

Date of testing
Date of data submittal

1/22/2008 - 3/4/10
4/5/2010

LAMINA MECHANICAL PROPERTY SUMMARY


Data reported as: Normalized & Measured
(Normalized by CPT= 0.0072 inch)
CTD Mean
Normalized
Measured

RTD Mean
Normalized Measured

ETD Mean
ETW Mean
Normalized Measured Normalized Measured

tu

F1 (ksi)
from LT
from UNT0

357.39
286.78

353.70
281.57

362.69
324.62

371.08
320.79

-----

-----

333.50
346.85

327.96
340.46

E1 (Msi)
of LT

22.57

22.33

22.99

23.51

---

---

24.00

23.77

E (Msi)
of UNT0

11.92

11.71

11.99

11.85

---

---

11.94

11.74

12
tu

0.270

0.316

0.393

(ksi)

---

9.60

---

9.29

---

---

---

3.49

E2 (Msi)
of TT

---

1.46

---

1.30

---

---

---

0.81

296.49

291.99

248.94

251.13

201.93

199.50

173.00

172.58

E1 (Msi)
of LC

20.68

20.53

20.04

20.44

20.25

20.00

20.37

20.65

E (Msi)
of UNC0

7.75

7.64

7.47

7.52

7.57

7.53

7.74

7.82

---

0.362

---

55.31

---

41.44

---

---

---

19.02

---

1.53

---

1.41

---

---

---

1.18

2 1
of TC

---

0.028

---

0.024

---

---

---

0.018

of UNC0

F2

cu

F1 (ksi)
from UNC0
c

12

0.356

0.374

0.383

cu

(ksi)
F2
of TC
c

E2 (Msi)
of TC
c

---

0.041

s5%strain

---

---

---

13.22

---

---

---

5.54

F12
(ksi)

s0.2%

---

11.29

---

7.76

---

---

---

3.31

---

0.86

---

0.68

---

---

---

0.31

--21.04
SBS
(ksi)
* Derived from cross-ply using back-out factor

---

17.13

---

11.23

---

8.25

F12
(ksi)

G 12
(Msi)

0.035

0.030

Table 2-1: Lamina Summary Data

Page 33 of 238

0.017

CAM-RP-2009-015 April 22, 2011 Revision A

2.2 Laminate Level Test Summary


Prepreg Material:

Hexcel Corporation - Hexcel 8552 IM7 Unidirectional


NMS 128/2 Material Specification

Fiber

IM7 unidirectional

Resin

Hexcel 8552

Tg(dry)

406.43 F

Tg(wet)

321.41 F

NPS 81228 "M" Cure Cycle


Lot 1
Lot 2
01/26/2007
12/25/2006
of fiber manufacture
02/28/2007
01/24/2007
of resin manufacture
02/28/2007
01/24/2007
of prepreg manufacture
9/2007 to 10/2007
of composite manufacture

Hexcel 8552 IM7


Laminate Properties
Summary
Tg METHOD

DMA (SRM 18-94)

PROCESSING:
Date
Date
Date
Date

Lot 3
02/05/2007
03/01/2007
03/01/2007

Date of testing
Date of data submittal

1/22/2008 - 3/4/10
4/5/2010

LAMINATE MECHANICAL PROPERTY SUMMARY


Data reported as: Normalized & Measured
(Normalized by CPT= 0.0072 inch)
Layup:
Test Condition

25/50/25
Normalized
Measured

10/80/10
Normalized
Measured

Normalized

50/40/10
Measured

OHT
Strength (ksi)

CTD
RTD
ETW

57.75
59.00
66.97

57.28
58.70
66.48

45.95
43.65
38.39

45.63
43.65
38.34

78.75
86.59
114.86

77.97
86.63
113.87

OHC
Strength (ksi)

RTD
ETW

49.08
35.52

48.89
35.29

38.80
25.76

38.40
25.57

63.24
46.42

63.36
46.22

UNT
Strength (ksi)

CTD
RTD
ETW

99.35
104.69
112.46

98.79
104.01
111.50

70.22
67.01
54.17

68.97
67.08
53.44

174.18
175.63
187.43

173.12
176.22
187.30

Modulus (msi)

CTD
RTD
ETW

8.35
8.39
7.99

8.30
8.34
7.92

5.52
5.22
4.47

5.42
5.23
4.41

13.11
13.15
13.14

13.02
13.20
13.15

UNC
Strength (ksi)

RTD
ETW

87.05
57.68

86.95
57.09

66.44
40.61

67.49
40.43

120.84
79.42

121.06
78.79

Modulus (msi)

RTD
ETW

7.86
7.13

7.86
7.06

4.90
4.10

4.98
4.06

11.90
11.77

11.93
11.66

UNC

RTD
ETW

-----

0.334
0.356

-----

0.587
0.665

-----

0.423
0.416

FHT
Strength (ksi)

CTD
RTD
ETW

64.02
65.87
70.29

63.52
65.95
69.52

52.25
48.15
42.63

52.05
48.08
42.30

80.70
91.95
101.26

80.53
91.93
100.77

FHC
Strength (ksi)

RTD
ETW

69.19
51.68

69.30
51.61

54.57
41.17

54.25
40.86

98.57
72.79

98.16
72.20

LSBS
Strength (ksi)

RTD
ETW

-------

12.13
6.99

-------

-------

-------

-------

SSB
2% offset Strength
Strength (ksi)

RTD
ETW

109.89
88.14

112.98
89.88

114.02
86.22

114.20
86.87

113.90
91.67

113.93
91.80

CTD
RTD
ETW
RTD

------31.45

11.96
11.04
6.46
30.96

---------

---------

---------

---------

ILT
Strength (ksi)
CAI
Strength (ksi)

Table 2-2: Laminate Summary Data


Page 34 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

2.3 Individual Test Summaries


2.3.1 Longitudinal Tension Properties
Material:

HEXCEL 8552 - IM7 UNI PREPREG

Resin content:

42.70 % vol

Fiber volum e:

57.30 % vol

Ply count:

Test m ethod:

ASTM D3039-00E1

Norm alized by:

0.0072 in CPT

Tension, 1-axis
Gr/ Ep
HEXCEL 8552 - IM7 UNI PREPREG

Com p. density: 1.58 [g/cc]

[0]6
Modulus calculation: linear fit from 1000 to 3000 micro in/in

CTD (B)

RTD (A)

Test Tem perature [F]

-65F

70F

ETW (D)
250F

Moisture Conditioning

dry

dry

equilibrium

HFIJXXXXB

HFIJXXXXA

HFIJXXXXD

160 F,85%

Equilibrium at T, RH
Source code

F1tu

Norm alized

Measured

Norm alized

Measured

Norm alized

Measured

Mean

357.39

353.70

362.69

371.08

333.50

327.96

Minim um

325.69

322.58

325.68

340.31

244.53

241.83

Maxim um

379.97

378.95

392.32

401.22

373.23

366.86

3.53

3.70

4.43

4.10

11.64

10.73

C.V.(%)

(ksi)

E1t

No. Specim ens

22

18

No. Prepreg Lots

18
3

Mean

22.57

22.33

22.99

23.51

24.00

23.77

Minim um

21.85

21.74

20.71

22.78

23.22

22.69

Maxim um

23.22

22.97

23.94

24.38

25.58

26.17

C.V.(%)

1.72

1.65

3.53

2.27

2.32

2.92

(Msi)
No. Specim ens

22

18

No. Prepreg Lots

0.270

0.316

0.393

No. Specim ens

22

18

25

No. Prepreg Lots

Mean
12t

Page 35 of 238

29

Norm alized

Measured

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.2 Transverse Tension Properties


Material:

HEXCEL 8552 - IM7 UNI PREPREG

Resin content:

40.08 % vol

Fiber volum e:

59.92 % vol

Ply count:

11

Test m ethod:

ASTM D3039-00

Norm alized by:

NA

Tension, 2-axis
Com p. density:

Gr/ Ep
HEXCEL 8552 - IM7 UNI PREPREG

1.58 [g/cc]

[90]11
Modulus calculation: linear fit from 1000 to 3000 micro in/in

CTD (B)

RTD (A)

Test Tem perature [F]

-65F

70F

ETW(D)
250F

Moisture Conditioning

dry

dry

equilibrium

HFIUXXXXB

HFIUXXXXA

HFIUXXXXD

160 F,85%

Equilibrium at T, RH
Source code

Norm alized

Measured

F2tu

Norm alized

Measured

9.60

Mean

Norm alized

Measured

9.29

3.49

Minim um

7.88

7.40

3.22

Maxim um

11.19

10.80

3.91

C.V.(%)

8.30

9.47

6.28

(ksi)

E2t

No. Specim ens

21

20

No. Prepreg Lots

19
3

Mean

1.46

1.30

0.81

Minim um

1.42

1.21

0.76

Maxim um

1.53

1.40

0.89

C.V.(%)

2.04

3.37

5.15

(Msi)
No. Specim ens

21

20

19

No. Prepreg Lots

Page 36 of 238

Norm alized

Measured

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.3 Longitudinal Compression Properties


Material:

HEXCEL 8552 - IM7 UNI PREPREG

Resin content:

38.92 % vol

Fiber volum e:

61.08 % vol

Ply count:

14

Test m ethod:

ASTM D6641M-01E1

Norm alized by:

0.0072 in CPT

Compression, 1-axis
Com p. density:

Gr/ Ep
HEXCEL 8552 - IM7 UNI
PREPREG

1.58 [g/cc]

[0]14
Modulus calculation: linear fit from 1000 to 3000 micro in/in

CTD (B)

RTD (A)

ETD

Test Tem perature [F]

-65F

70F

250F

ETW (D)
250F

Moisture Conditioning

dry

dry

dry

equilibrium

HFILXXXXB

HFILXXXXA

HFILXXXXC

HFILXXXXD

160 F,85%

Equilibrium at T, RH
Source code

E1c

Norm alized

Measured

Norm alized

Measured

Norm alized

Measured

Mean

20.68

20.53

20.04

20.44

20.25

20.00

Norm alized Measured


20.37

20.65

Minim um

17.80

19.05

18.19

19.80

18.37

19.37

15.61

17.67

Maxim um

22.39

21.29

22.43

20.89

22.12

20.92

24.76

26.64

C.V.(%)

6.40

2.94

6.81

1.55

5.76

2.31

9.00

8.49

(Msi)
No. Specim ens

20

15

17

No. Prepreg Lots

0.362

0.356

0.374

0.383

No. Specim ens

20

15

17

35

No. Prepreg Lots

Mean
12 c

Page 37 of 238

35

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.4 Transverse Compression Properties


Material:

HEXCEL 8552 - IM7 UNI PREPREG

Resin content:

39.62 % vol

Fiber volum e:

60.38 % vol

Ply count:

14

Test m ethod:

ASTM D6641-01e1

Compression, 2-axis
1.58 [g/cc]

Com p. density:

Gr/ Ep
HEXCEL 8552 - IM7 UNI PREPREG

[90]14
Modulus calculation: linear fit from 1000 to 3000 micro in/in

Norm alized by: NA


CTD (B)

RTD (A)

Test Tem perature [F]

-65F

70F

ETW (D)
250F

Moisture Conditioning

dry

dry

equilibrium

HFIZXXXXB

HFIZXXXXA

HFIZXXXXD

160 F,85%

Equilibrium at T, RH
Source code

Norm alized

F2cu

Measured

Norm alized

Measured

Norm alized

Measured

Mean

55.31

41.44

19.02

Minim um

50.41

38.79

16.78

Maxim um

61.39

46.40

20.70

C.V.(%)

5.19

4.50

5.47

(ksi)

E2c

No. Specim ens

20

20

No. Prepreg Lots

25
3

Mean

1.53

1.41

1.18

Minim um

1.26

1.25

1.03

Maxim um

1.70

1.66

1.35

C.V.(%)

7.64

6.63

7.99

(Msi)
No. Specim ens

20

20

No. Prepreg Lots

0.028

0.024

0.018

No. Specim ens

20

20

No. Prepreg Lots

Mean
21

Page 38 of 238

Norm alized

Measured

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.5 In-Plane Shear Properties


Material:

HEXCEL 8552 - IM7 UNI PREPREG

Resin content:

41.07 % vol

Fiber volum e:

58.93 % vol

Ply count:

12

Test m ethod:

ASTM D3518-94

Norm alized by:

NA

In-Plane Shear
Gr/ Ep
HEXCEL 8552 - IM7 UNI
PREPREG

Com p. density: 1.57 [g/cc]

[+45/-45]3s
Modulus calculation: linear fit from 2000 to 6000 micro in/in
CTD (B)

RTD (A)

Test Temperature [F]

-65F

70F

250F

Moisture Conditioning

dry

dry

equilibrium

HFINXXXXB

HFINXXXXA

160 F,85%
HFINXXXXD

Equilibrium at T, RH
Source code

Norm alized

F12s5% strain
(ksi)

F12s0.2%

Measured

Norm alized

ETW (D)

Measured

Norm alized

Measured

Mean

13.22

5.54

Minim um

12.85

5.18

Maxim um

13.61

5.95

C.V.(%)

1.60

3.38

No. Specim ens

12

No. Prepreg Lots


Mean
Minim um

19

11.29
10.78

7.76
7.48

3.31
3.05

Maxim um

11.66

8.28

3.63

C.V.(%)

2.10

2.81

4.63

(ksi)

G12s

No. Specim ens

21

16

No. Prepreg Lots

20
3

Mean

0.86

0.68

0.31

Minim um

0.81

0.65

0.28

Maxim um
C.V.(%)

0.89
2.90

0.73
3.27

0.34
4.51

(Msi)
No. Specim ens

21

16

20

No. Prepreg Lots

Note: All CTD specim ens failed to reach 50,000 m icrostrain

Page 39 of 238

Norm alized

Measured

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.6 Unnotched Compression 0 Properties


Material:

HEXCEL 8552 - IM7 UNI PREPREG

Resin content:

39.67 % vol

Fiber volum e:

60.30 % vol

Ply count:

15

Test m ethod:

ASTM D6641-01E1

Unnotched Compression 0
Gr/ Ep
HEXCEL 8552 - IM7 UNI PREPREG

Com p. density: 1.58 [g/cc]

[90,0,90]5
Modulus calculation: linear fit from 1000 to 3000 micro in/in

Norm alized by: 0.0072 in CPT


CTD (B)

RTD (A)

ETD (C)

-65F
dry

70F

250F

250 F

dry

dry

equilibrium

HFIRXXXXB

HFIRXXXXA

HFIRXXXXC

HFIRXXXXD

Test Tem perature [F]


Moisture Conditioning

ETW (D)

160 F,85%

Equilibrium at T, RH
Source code

Norm alized

Measured

Norm alized

Measured

Nom alized

Measured

Norm alized

Measured

Mean

113.26

111.64

94.51

95.11

75.53

75.13

64.28

64.03

Minim um

105.46

104.58

84.82

89.79

66.78

66.57

53.94

52.06

Maxim um

121.75

118.90

99.74

98.54

81.34

81.64

70.95

74.96

4.19

4.02

5.91

3.22

6.61

6.81

8.23

9.70

UNC0
C.V.(%)
Strength (ksi)

UNC0

No. Specim ens

No. Prepreg Lots

17
2

Mean

7.75

7.64

7.47

7.52

7.57

7.53

7.74

7.82

Minim um

7.47

7.43

7.04

7.32

7.11

7.11

7.41

7.30

Maxim um

8.03

7.85

7.60

7.73

7.88

7.84

8.12

8.22

C.V.(%)

3.08

2.36

2.62

1.53

3.41

3.12

3.04

3.88

Modulus (Msi)
No. Specim ens
No. Prepreg Lots
Mean
UNC0

2
0.041

2
0.035

2
0.030

2
0.017

No. Specim ens

No. Prepreg Lots

Batch A Cure Cycle 1 and 2 and Batch C Cure Cycle 2 has improper layup so data was removed

Page 40 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.7 Unnotched Tension 0 Properties


Material:

HEXCEL 8552 - IM7 UNI PREPREG

Resin content:

40.79 % vol

Fiber volum e:

59.21 % vol

Ply count:

Test m ethod:

ASTM D3039M-00E1

Norm alized by:

0.0072 in CPT

Unnotched Tension 0
Gr/ Ep
HEXCEL 8552 - IM7 UNI PREPREG

Com p. density: 1.58 [g/cc]

[0,90]2S

Modulus calculation: linear fit from 1000 to 3000 micro in/in

CTD (B)

RTD (A)

Test Tem perature [F]

-65F

70F

ETW (D)
250F

Moisture Conditioning

dry

dry

equilibrium

HFIPXXXXB

HFIPXXXXA

HFIPXXXXD

160 F,85%

Equilibrium at T, RH
Source code

UNT0

Norm alized

Measured

Norm alized

Measured

Norm alized

Measured

Mean

152.58

149.90

171.38

169.16

179.23

175.98

Minim um

142.06

138.38

143.99

150.39

165.98

164.55

Maxim um

159.85

156.68

182.90

182.06

189.18

189.34

3.39

3.61

5.43

4.18

3.75

3.67

C.V.(%)

Strength (ksi)

UNT0

No. Specim ens

19

18

No. Prepreg Lots

18
3

Mean

11.92

11.71

11.99

11.85

11.94

11.74

Minim um

11.55

11.25

11.50

11.33

11.60

11.29

Maxim um

12.15

11.91

12.34

12.46

12.35

12.26

C.V.(%)

1.24

1.61

1.76

2.50

1.76

2.09

Modulus (Msi)
No. Specim ens

19

18

19

No. Prepreg Lots

Page 41 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.8 Short Beam Strength Properties


Material:

HEXCEL 8552 - IM7 UNI PREPREG

Resin content:

38.85 % vol

Fiber volum e:

61.15 % vol

Ply count:

34

Test m ethod:

ASTM D2344-00E1

Norm alized by:

N/A

Short Beam Strength


Gr/ Ep
HEXCEL 8552 - IM7 UNI PREPREG

Com p. density: 1.58 [g/cc]

[0]34

CTD (B)

RTD (A)

ETD (C)

Test Tem perature [F]

-65F

70F

250F

ETW (D)
250F

Moisture Conditioning

dry

dry

dry

equilibrium

HFIQXXXXB

HFIQXXXXA

HFIQXXXXC

HFIQXXXXD

160 F,85%

Equilibrium at T, RH
Source code

Norm alized

SBS

Measured

Norm alized

Measured

Norm alized

Measured

Norm alized

Measured

Mean

21.04

17.13

11.23

8.25

Minim um

19.68

16.20

10.96

7.86

Maxim um

22.58

17.78

11.77

8.82

C.V.(%)

3.05

2.51

1.94

2.93

Strength (ksi)
No. Specim ens

19

18

19

19

No. Prepreg Lots

Page 42 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.9 Unnotched Tension 1 Properties


Material: HEXCEL 8552 - IM7 UNI PREPREG
Resin content:

42.20 % vol

Fiber volum e:

57.80 % vol

Ply count:

16

Test m ethod:

ASTM D3039M-00e1

Norm alized by:

0.0072 in CPT

Unnotched Tension 1
Gr/ Ep
HEXCEL 8552 - IM7 UNI PREPREG

Com p. density: 1.58 g[cc]

[45,0,-45,90]2s

Modulus calculation: linear fit from 1000 to 3000 micro in/in

CTD (B)

RTD (A)

Test Tem perature [F]

-65F

70F

ETW (D)
250F

Moisture Conditioning

dry

dry

equilibrium

HFIAXXXXB

HFIAXXXXA

HFIAXXXXD

160 F,85%

Equilibrium at T, RH
Source code

UNT1

Norm alized

Measured

Norm alized

Measured

Norm alized

Mean

99.35

98.79

104.69

104.01

112.46

111.50

Minim um

91.60

93.70

89.56

96.38

101.64

104.09

Maxim um

105.84

104.20

113.71

111.12

119.29

119.12

3.46

2.78

6.95

3.90

4.99

3.50

C.V.(%)

Measured

Strength (ksi)

UNT1

No. Specim ens

16

16

No. Prepreg Lots

17
3

Mean

8.35

8.30

8.39

8.34

7.99

7.92

Minim um

7.29

7.91

7.28

7.90

7.07

7.15

Maxim um

8.75

8.52

8.98

8.69

8.51

8.29

C.V.(%)

3.70

1.74

5.73

2.68

5.16

3.86

Modulus (Msi)
No. Specim ens

16

16

17

No. Prepreg Lots

Page 43 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.10

Unnotched Tension 2 Properties

Material:

HEXCEL 8552 - IM7 UNI PREPREG

Resin content:

40.91 % vol

Fiber volum e:

59.09 % vol

Ply count:

20

Test m ethod:

ASTM D3039M-00E1

Normalized by:

0.0072 in CPT

Unnotched Tension 2
Gr/ Ep
HEXCEL 8552 - IM7 UNI PREPREG

Com p. density: 1.58 [g/cc]

[45,-45,0,45,-45,90,45,-45,45,-45]S

Modulus calculation: linear fit from 1000 to 3000 micro in/in

CTD (B)

RTD (A)

Test Tem perature [F]

-65F

70F

ETW (D)
250F

Moisture Conditioning

dry

dry

equilibrium

HFIBXXXXB

HFIBXXXXA

HFIBXXXXD

160 F,85%

Equilibrium at T, RH
Source code

UNT2
Strength (ksi)

UNT2

Norm alized

Measured

Norm alized

Measured

Normalized

Measured

Mean

70.22

68.97

67.01

67.08

54.17

53.44

Minim um

66.60

65.98

57.64

62.42

50.96

50.23

Maxim um

75.29

72.93

71.95

69.98

56.23

56.42

C.V.(%)

2.54

2.33

5.69

3.17

2.49

2.90

No. Specim ens

17

18

No. Prepreg Lots

18
3

Mean

5.52

5.42

5.22

5.23

4.47

4.41

Minim um

5.31

5.14

4.70

4.95

4.33

4.28

Maxim um

5.77

5.62

5.72

5.54

4.65

4.51

C.V.(%)

2.03

2.26

5.27

3.31

2.13

1.93

Modulus (Msi)
No. Specim ens

17

18

18

No. Prepreg Lots

Page 44 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.11

Unnotched Tension 3 Properties

Material: HEXCEL 8552 - IM7 UNI PREPREG


Resin content:

41.31 % vol

Fiber volum e:

58.69 % vol

Ply count:

20

Test m ethod:

ASTM D3039M-00E1

Norm alized by:

0.0072 in CPT

Unnotched Tension 3
Gr/ Ep
HEXCEL 8552 - IM7 UNI PREPREG

Com p. density: 1.58 [g/cc]

[0,45,0,90,0,45,0,-45]s

Modulus calculation: linear fit from 1000 to 3000 micro in/in

CTD (B)

RTD (A)

Test Tem perature [F]

-65F

70F

ETW (D)
250F

Moisture Conditioning

dry

dry

equilibrium

HFICXXXXB

HFICXXXXA

HFICXXXXD

160 F,85%

Equilibrium at T, RH
Source code

UNT3

Norm alized

Measured

Norm alized

Measured

Norm alized

Measured

Mean

174.18

173.12

175.63

176.22

187.43

187.30

Minim um

159.91

160.82

159.04

158.49

161.56

172.30

Maxim um

188.80

187.85

188.00

190.86

203.39

199.33

4.47

4.74

4.78

4.21

5.84

4.33

C.V.(%)

Strength (ksi)

UNT3

No. Specim ens

19

22

No. Prepreg Lots

19
3

Mean

13.11

13.02

13.15

13.20

13.14

13.15

Minim um

12.57

12.36

11.50

11.40

11.69

12.48

Maxim um

13.60

13.41

15.13

14.84

14.41

13.90

C.V.(%)

1.98

2.17

6.04

5.63

4.65

2.68

Modulus (Msi)
No. Specim ens

19

22

22

No. Prepreg Lots

Page 45 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.12

Unnotched Compression 1 Properties

Material:

HEXCEL 8552 - IM7 UNI PREPREG

Resin content:

40.04 % vol

Fiber volum e:

59.96 % vol

Ply count:

16

Test m ethod:

ASTM D6641-01E1

Unnotched Compression 1
Gr/ Ep
HEXCEL 8552 - IM7 UNI PREPREG

Com p. density: 1.58 [g/cc]

[45,0,-45,90]2S

Modulus calculation: linear fit from 1000 to 3000 micro in/in

Norm alized by: 0.0072 in CPT


RTD (A)

ETW (D)

Test Tem perature [F]

70F

250 F

Moisture Conditioning

dry

equilibrium

HFIWXXXXA

HFIWXXXXD

160 F,85%

Equilibrium at T, RH
Source code

Norm alized

Measured

Norm alized

Measured

Mean

87.05

86.95

57.68

57.09

Minim um

68.07

73.46

48.72

48.54

Maxim um

97.04

96.78

72.23

70.98

9.32

7.51

11.02

10.87

UNC1
C.V.(%)
Strength (ksi)

UNC1

No. Specim ens

16

No. Prepreg Lots

30
3

Mean

7.86

7.86

7.13

7.06

Minim um

6.89

7.20

6.85

6.79

Maxim um

8.41

8.61

7.34

7.38

C.V.(%)

4.75

4.86

1.80

2.28

Modulus (Msi)
No. Specim ens

16

No. Prepreg Lots

0.334

0.356

No. Specim ens

16

16

No. Prepreg Lots

Mean
UNC1

16

Page 46 of 238

Norm alized

Measured

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.13

Unnotched Compression 2 Properties

Material:

HEXCEL 8552 - IM7 UNI PREPREG

Resin content:

38.98 % vol

Fiber volum e:

61.02 % vol

Ply count:

20

Test m ethod:

ASTM D6641-01E1

Norm alized by:

0.0072 in CPT

Unnotched Compression 2
1.58 [g/cc]

Com p. density:

Gr/ Ep
HEXCEL 8552 - IM7 UNI PREPREG

[45,-45,0,45,-45,90,45,-45,45,-45]S

Modulus calculation: linear fit from 1000 to 3000 micro in/in

RTD (A)

ETW

Test Tem perature [F]

70F

250F

Moisture Conditioning

DRY

equilibrium
160 F,85%

Equilibrium at T, RH
HFIXXXXXA

Source code

UNC2

HFIXXXXXD

Norm alized

Measured

Norm alized

Measured

Mean

66.44

67.49

40.61

40.43

Minim um

57.29

60.87

31.19

31.31

Maxim um

72.61

73.01

50.34

49.44

C.V.(%)

7.36

5.53

10.91

10.71

Strength (ksi)

UNC2

No. Specim ens

16

No. Prepreg Lots

31
3

Mean

4.90

4.98

4.10

4.06

Minim um

4.35

4.58

3.96

3.85

Maxim um

5.35

5.33

4.25

4.18

C.V.(%)

6.10

4.84

2.21

2.72

Modulus (Msi)
No. Specim ens

16

No. Prepreg Lots

0.587

0.665

No. Specim ens

16

16

No. Prepreg Lots

Mean
UNC2

Page 47 of 238

16

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.14
Material:

Unnotched Compression 3 Properties


HEXCEL 8552 - IM7 UNI PREPREG

Resin content:

40.22 % vol

Fiber volume:

59.78 % vol

Ply count

20

Test m ethod:

ASTM D6641-01E1

Normalized by:

0.0072 in CPT

Com p. density:

1.58 [g/cc]

Unnotched Compression
3
Gr/ Ep
HEXCEL 8552 - IM7 UNI
PREPREG

[45,0,90,0,-45,0,45,0,-45,0]S
Modulus calculation: linear fit from 1000 to 3000 micro in/in
RTD (A)

ETW

Test Tem perature [F]

70F

250F

Moisture Conditioning

dry

equilibrium
160 F,85%

Equilibrium at T, RH
HFIYXXXXA

Source code

UNC3
Strength (ksi)

UNC3

HFIYXXXXD

Normalized

Measured

Norm alized

Measured

Mean

120.84

121.06

79.42

78.79

Minim um

108.20

111.74

68.05

67.56

Maxim um

136.09

137.70

96.63

94.50

5.86

5.53

10.31

9.99

C.V.(%)
No. Specim ens

16

No. Prepreg Lots

27
3

Mean

11.90

11.93

11.77

11.66

Minim um

10.32

11.20

11.24

11.22

Maxim um

12.58

12.74

12.22

11.96

C.V.(%)

4.35

3.38

2.35

2.09

Modulus (Msi)
No. Specim ens

17

No. Prepreg Lots

0.423

0.416

No. Specim ens

17

15

No. Prepreg Lots

Mean
UNC3

Page 48 of 238

15

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.15

Laminate Short Beam Strength Properties

Material:

HEXCEL 8552 - IM7 UNI PREPREG

Resin content:

34.55 % vol

Fiber volum e:

65.45 % vol

Ply count:

24

Test m ethod:

ASTM D2344-00E1

Norm alized by:

NA

Laminate Short Beam Strength


Gr/ Ep
HEXCEL 8552 - IM7 UNI PREPREG
[45,0,-45,90]3s

Com p. density: 1.58 [g/cc]

RTD (A)

ETW (D)

Test Tem perature [F]

70F

250F

Moisture Conditioning

dry

equilibrium
160 F,85%

Equilibrium at T, RH
HFIqXXXA

Source code

Norm alized

Norm alized

Measured

12.13

Mean

LSBS

HFIqXXXD

Measured

6.99

Minim um

9.55

6.63

Maxim um

12.98

7.70

C.V.(%)

6.85

3.65

(ksi)
No. Specim ens

21

19

No. Prepreg Lots

physical testing only available from batch A cure 1

Page 49 of 238

Norm alized

Measured

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.16

Open Hole Tension 1 Properties

Material: HEXCEL 8552 - IM7 UNI PREPREG

Open Hole Tension 1


Gr/ Ep

Resin content:

42.20 % vol

Fiber volum e:

57.80 % vol

Ply count:

16

Test m ethod:

ASTM D5766M-02a

Norm alized by:

0.0072 in CPT

Com p. density: 1.57 [g/cc] HEXCEL 8552 - IM7 UNI PREPREG

[45,0,-45,90]2S

CTD (B)

RTD (A)

Test Tem perature [F]

-65F

70F

ETW (D)
250F

Moisture Conditioning

dry

dry

equilibrium
160 F,85%

Equilibrium at T, RH
HFIDXXXXB

Source code

OHT1

HFIDXXXXA

HFIDXXXXD

Norm alized

Measured

Norm alized

Measured

Norm alized

Measured

Mean

57.75

57.28

59.00

58.70

66.97

66.48

Minim um

53.64

53.27

54.12

53.32

62.15

62.21

Maxim um

62.52

61.67

64.61

64.44

72.59

72.59

C.V.(%)

4.21

3.95

3.98

4.07

4.26

4.29

Strength (ksi)
No. Specim ens

19

19

20

No. Prepreg Lots

Page 50 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.17

Open Hole Tension 2 Properties

Material:

HEXCEL 8552 - IM7 UNI PREPREG

Resin content:

40.64 % vol

Fiber volum e:

59.36 % vol

Ply count

20

Test m ethod:

ASTM D5766-02a

Norm alized by:

0.0072 in CPT

Open Hole Tension 2


Gr/ Ep
HEXCEL 8552 - IM7 UNI PREPREG
[45,-45,0,45,-45,90,45,-45,45, -45]s

1.58 [g/cc]
Com p. density:

CTD (B)

RTD (A)

Test Tem perature [F]

-65F

70F

ETW (D)
250F

Moisture Conditioning

dry

dry

equilibrium

HFIEXXXXB

HFIEXXXXA

HFIEXXXXD

160 F,85%

Equilibrium at T, RH
Source code

OHT2

Norm alized

Measured

Norm alized

Measured

Norm alized

Measured

Mean

45.95

45.63

43.65

43.65

38.39

38.34

Minim um

44.04

43.88

39.91

41.05

36.27

36.18

Maxim um

47.20

47.02

45.96

45.86

40.71

40.04

C.V.(%)

1.92

2.16

3.28

2.77

3.10

3.11

Strength (ksi)
No. Specim ens

19

19

18

No. Prepreg Lots

Page 51 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.18

Open Hole Tension 3 Properties

Material:

HEXCEL 8552 - IM7 UNI PREPREG

Resin content:

40.45

Fiber volum e:

59.55

Ply count:

20

Test m ethod:

ASTM D5766-02a

Norm alized by:

0.0072 in CPT

Open Hole Tension 3


Gr/ Ep
HEXCEL 8552 - IM7 UNI PREPREG

Com p. density:1.58 [g/cc]

[0,45,0,90,0,-45,0,45,0,-45]S

CTD (B)

RTD (A)

Test Tem perature [F]

-65F

70F

ETW (D)
250F

Moisture Conditioning

dry

dry

equilibrium

HFIFXXXXB

HFIFXXXXA

HFIFXXXXD

160 F,85%

Equilibrium at T, RH
Source code

OHT3

Norm alized

Measured

Norm alized

Measured

Norm alized

Mean

78.75

77.97

86.59

86.627

114.86

Measured
113.87

Minim um

72.41

70.75

78.90

79.07

105.04

102.24

Maxim um

84.29

84.38

95.17

94.49

129.75

128.78

C.V.(%)

5.03

6.01

5.46

5.72

5.95

6.37

Strength (ksi)
No. Specim ens

19

19

20

No. Prepreg Lots

Page 52 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.19

Filled-Hole Tension 1 Properties


Filled-Hole Tension 1

Material: HEXCEL 8552 - IM7 UNI PREPREG


Resin content:

40.79 % vol

Fiber volum e:

59.21 % vol

Ply count:

16

Test m ethod:

ASTM D6742M-02

Norm alized by:

0.0072 in CPT

Gr/ Ep
HEXCEL 8552 - IM7 UNI PREPREG

Com p. density: 1.58 [g/cc]

[45,0,-45,90]2S

CTD (B)

RTD (A)

Test Tem perature [F]

-65F

70F

ETW(D)
250F

Moisture Conditioning

dry

dry

equilibrium

HFIXXXXB

HFI4XXXXA

HFI4XXXXD

160 F,85%

Equilibrium at T, RH
Source code

FHT1

Norm alized

Measured

Norm alized

Measured

Norm alized

Measured

Mean

64.02

63.52

65.87

65.95

70.29

69.52

Minim um

58.00

57.30

59.20

59.60

65.17

64.29

Maxim um

69.40

68.01

72.34

72.19

74.40

74.58

C.V.(%)

4.39

4.86

4.95

5.41

3.24

3.90

Strength (ksi)
No. Specim ens
No. Prepreg Lots

19
3

19
3

Page 53 of 238

22
3

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.20

Filled-Hole Tension 2 Properties

Material:

HEXCEL 8552 - IM7 UNI PREPREG

Resin content:

39.04 % vol

Fiber volum e:

60.96 % vol

Ply count:

20

Test m ethod:

ASTM D6742M-02

Norm alized by:

0.0072 in CPT

Filled-Hole Tension 2
Gr/ Ep
HEXCEL- IM7 UNI PREPREG

[45,-45,0,45,-45,90,45,-45,45-,45]S

Com p. density: 1.59 [g/cc]

CTD (B)

RTD (A)

Test Tem perature [F]

-65F

70F

ETW (D)
250F

Moisture Conditioning

dry

dry

equilibrium

HFI5XXXXB

HFI5XXXXA

HFI5XXXXD

160 F,85%

Equilibrium at T, RH
Source code

FHT2
Strength (ksi)

Norm alized

Measured

Norm alized

Measured

Norm alized

Measured

Mean

52.25

52.05

48.15

48.08

42.63

42.30

Minim um

48.54

50.23

44.59

44.67

41.22

40.75

Maxim um

54.64

54.73

50.79

50.24

43.75

43.54

C.V.(%)

3.00

2.53

4.03

3.34

1.73

1.97

No. Specim ens

19

19

19

No. Prepreg Lots

Note: The physical testing data is missing averages from Batch B cure cycle 1.

Page 54 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.21

Filled-Hole Tension 3 Properties

Material:

HEXCEL 8552 - IM7 UNI PREPREG

Resin content:

40.33 % vol

Fiber volum e:

59.67 % vol

Ply count:

20

Test m ethod:

ASTM D6742M-02

Normalized by:

0.0072 in CPT

Filled-Hole Tension 3
Gr/ Ep
HEXCEL 8552 - IM7 UNI
PREPREG

Com p. density: 1.58 [g/cc]

[0,45,0,90,0,-45,0,45,0-45]s

CTD (B)

RTD (A)

Test Tem perature [F]

-65F

70F

ETW (D)
250F

Moisture Conditioning

dry

dry

equilibrium

HFI6XXXXB

HFI6XXXXA

HFI6XXXXD

160 F,85%

Equilibrium at T, RH
Source code

FHT3
Strength (ksi)

Norm alized

Measured

Norm alized

Measured

Normalized

Measured

Mean

80.70

80.53

91.95

91.93

101.26

100.77

Minim um

70.25

71.22

79.15

77.08

93.92

92.01

Maxim um

88.15

88.23

102.16

102.61

108.11

107.29

C.V.(%)

5.69

6.13

7.20

7.91

3.90

3.82

No. Specim ens

19

19

19

No. Prepreg Lots

Page 55 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.22

Open Hole Compression 1 Properties

Material:

HEXCEL 8552 - IM7 UNI PREPREG

Resin content:

41.74 % vol

Fiber volum e:

58.26% vol

Ply count:

24

Test m ethod:

ASTM D6484M-04

Norm alized by:

0.0072 in CPT

Open Hole Compression 1


Gr/ Ep
HEXCEL 8552 - IM7 UNI PREPREG
[45,0,-45,90]3S

Com p. density: 1.58 [g/cc]

RTD (A)

ETW (D)

Test Tem perature [F]

70F

250F

Moisture Conditioning

dry

equilibrium

HFIGXXXXA

HFIGXXXXD

160 F,85%

Equilibrium at T, RH
Source code

OHC1

Norm alized

Measured

Norm alized

Measured

Mean

49.08

48.89

35.52

35.29

Minim um

43.91

45.15

33.08

33.59

Maxim um

50.99

51.28

38.96

37.50

C.V.(%)

3.65

2.96

4.07

3.25

Strength (ksi)
No. Specim ens

19

19

No. Prepreg Lots

Page 56 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.23

Open Hole Compression 2 Properties

Material:

HEXCEL 8552 - IM7 UNI PREPREG

Resin content:

41.14 % vol

Fiber volume:

58.86 % vol

Ply count:

20

Test method:

ASTM D6484M-04

Normalized by:

0.0072 in CPT

Open Hole Compression 2


Gr/ Ep
HEXCEL 8552 - IM7 UNI PREPREG

1.58 [g/cc]

Com p. density:

[45,-45,0,45,-45,90,45,-45,45,-45]S

RTD (A)

ETW (D)

Test Tem perature [F]

70F

250F

Moisture Conditioning

dry

equilibrium

HFIHXXXXA

HFIHXXXXD

160 F,85%

Equilibrium at T, RH
Source code

OHC2

Norm alized

Measured

Norm alized

Measured

Mean

38.80

38.40

25.76

25.57

Minim um

36.25

35.93

22.36

22.24

Maximum

41.33

40.85

27.57

27.56

C.V.(%)

3.29

3.41

5.02

4.40

Strength (ksi)
No. Specim ens

18

20

No. Prepreg Lots

Page 57 of 238

Norm alized

Measured

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.24

Open Hole Compression 3 Properties

Material:

HEXCEL 8552 - IM7 UNI PREPREG

Resin content:

39.62 % vol

Gr/ Ep
HEXCEL 8552 - IM7 UNI PREPREG

Fiber volum e:

60.38 % vol

[0,45,0,90,0,-45,0,45,0,-45]S

Ply count:

20

Test m ethod:

ASTM D6484M-04

Norm alized by:

0.0072 in CPT

Open Hole Compression 3

Com p. density: 1.58 [g/cc]

RTD (A)

ETW (D)

Test Tem perature [F]

70F

250F

Moisture Conditioning

dry

equilibrium

HFIIXXXXA

HFIIXXXXD

160 F,85%

Equilibrium at T, RH
Source code

OHC3

Norm alized

Measured

Norm alized

Measured

Mean

63.24

63.36

46.42

46.22

Minim um

56.63

59.06

42.01

42.66

Maxim um

69.28

69.24

50.50

51.35

C.V.(%)

4.54

4.28

4.55

4.76

Strength (ksi)
No. Specim ens

19

20

No. Prepreg Lots

Page 58 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.25

Filled-Hole Compression 1 Properties

Material:

HEXCEL 8552 - IM7 UNI PREPREG

Resin content:

41.85 % vol

Fiber volume:

58.15 % vol

Ply count:

24

Test m ethod:

ASTM D6742M-02

Norm alized by:

0.0072 in CPT

Filled-Hole Compression 1
Gr/ Ep
1.58 [g/cc]

Comp. density:

HEXCEL 8552 - IM7 UNI


PREPREG
[45,0,-45,90]3S

RTD (A)

ETW (D)

Test Tem perature [F]

70F

250F

Moisture Conditioning

dry

equilibrium

HFI7XXXXA

HFI7XXXXD

160 F,85%

Equilibrium at T, RH
Source code

FHC1
Strength (ksi)

Norm alized

Measured

Norm alized

Measured

Mean

69.19

69.30

51.68

51.61

Minim um

62.34

62.44

47.70

47.93

Maxim um

76.17

76.20

55.60

54.57

C.V.(%)

5.34

5.56

4.41

3.85

No. Specim ens

20

19

No. Prepreg Lots

Page 59 of 238

Norm alized

Measured

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.26

Filled-Hole Compression 2 Properties

Material: HEXCEL 8552 - IM7 UNI PREPREG


Resin content:

41.09 % vol

Fiber volum e:

58.91 % vol

Ply count:

20

Test m ethod:

ASTM D6742M-02

Norm alized by:

0.0072 in CPT

Filled-Hole Compression 2
Gr/ Ep
HEXCEL 8552 - IM7 UNI PREPREG

Com p. density: 1.58 [g/cc]

[45,-45,0,45,-45,90,45,-45,45,-45]S

RTD (A)

ETW (D)

Test Tem perature [F]

70F

250F

Moisture Conditioning

dry

equilibrium
160 F,85%

Equilibrium at T, RH
HFI8XXXXA

Source code

FHC2
Strength (ksi)

HFIXXXXD

Normalized

Measured

Norm alized

Measured

Mean

54.57

54.25

41.17

40.86

Minim um

50.41

50.57

37.36

37.86

Maximum

57.71

57.54

43.99

43.20

C.V.(%)

4.13

3.17

4.39

3.66

No. Specim ens


No. Prepreg Lots

19
3

19
3

Page 60 of 238

Norm alized

Measured

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.27

Filled-Hole Compression 3 Properties

Material: HEXCEL 8552 - IM7 UNI PREPREG


Resin content:

41.63 % vol

Fiber volum e:

58.37 % vol

Ply count

20

Test m ethod:

ASTM D6742M-02

Norm alized by:

0.0072 in CPT

Filled-Hole Compression 3

Com p. density:

Gr/ Ep
HEXCEL 8552 - IM7 UNI PREPREG

1.58 [g/cc]

[0,45,0,90,0,-45,0,45,0,-45]s

RTD (A)

ETW (D)

Test Tem perature [F]

70F

250F

Moisture Conditioning

dry

equilibrium

HFI9XXXXA

HFI9XXXXD

160 F,85%

Equilibrium at T, RH
Source code
Mean

FHC3

Norm alized

Measured

Norm alized

Measured

98.57

98.16

72.79

72.20

Minim um

89.45

87.81

69.47

68.99

Maxim um

106.54

104.25

78.09

77.22

4.61

4.25

3.03

3.14

C.V.(%)

Strength (ksi)
No. Specim ens

18

19

No. Prepreg Lots

Page 61 of 238

Norm alized

Measured

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.28

Single Shear Bearing 1 Properties

Material:

HEXCEL 8552 - IM7 UNI PREPREG

Resin content:

40.38 % vol

Fiber volum e:

59.62 % vol

Ply count:

16

Test m ethod:

ASTM D5961M-05e1

Norm alized by:

0.0072 in CPT

Laminate Bearing 1
Gr/ Ep
HEXCEL 8552 - IM7 UNI PREPREG

1.58 [g/cc]

Com p. density:

[45,0,-45,90]2S

RTD (A)

ETW (D)

Test Tem perature [F]

70F

250F

Moisture Conditioning

dry

equilibrium

HFI1XXXXA

HFI1XXXXD

160 F,85%

Equilibrium at T, RH
Source code

SSB1

Norm alized

Measured

Norm alized

Measured

Mean

109.89

112.98

88.14

89.88

Minim um

99.31

106.30

69.19

68.62

Maxim um
C.V.(%)

119.86
5.51

118.98
3.56

101.13
10.10

99.81
9.49

2% offset Strength
(ksi)

No. Specim ens

19

21

No. Prepreg Lots

Ultimate Strength not obtained

Page 62 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.29

Single Shear Bearing 2 Properties

Material: HEXCEL 8552 - IM7 UNI PREPREG


Resin content:

40.40 % vol

Fiber volum e:

59.60 % vol

Ply count:

20

Test m ethod:

ASTM D5961M-05e1

Norm alized by:

0.0072 in CPT

Laminate Bearing 2
Com p. density: 1.58 [g/cc]

Gr/ Ep
HEXCEL 8552 - IM7 UNI PREPREG

[45,-45,0,45,-45,90,45,-45,45,-45]S

RTD (A)

ETW (D)

Test Tem perature [F]

70F

250F

Moisture Conditioning

dry

equilibrium

HFI2XXXXA

HFI2XXXXD

160 F,85%

Equilibrium at T, RH
Source code

SSB2

Norm alized

Measured

Norm alized

Measured

Mean

114.02

114.20

86.22

86.87

Minim um

100.30

104.42

78.40

77.48

Maxim um

121.80

122.56

94.73

97.23

4.88

3.86

6.52

6.21

C.V.(%)

2% offset Strength
(ksi)

No. Specim ens

19

19

No. Prepreg Lots

Physical testing not available for Batch A Cure Cycle 1


Ultim ate Strength not obtained

Page 63 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.30

Single Shear Bearing 3 Properties

Material: HEXCEL 8552 - IM7 UNI PREPREG


Resin content:

40.65 % vol

Fiber volum e:

59.35 % vol

Ply thickness:

0.0067 - 0.0075

Ply count:

20

Test m ethod:

ASTM D5961M-05e1

Norm alized by:

0.0072

Laminate Bearing 3
Gr/ Ep
HEXCEL 8552 - IM7 UNI
PREPREG

Com p. density: 1.58 [g/cc]

[0,45,0,90,0,-45,0,45,0,-45]S

RTD (A)

ETW (D)

Test Tem perature [F]

70F

250F

Moisture Conditioning

dry

equilibrium

HFI3XXXXA

HFI3XXXXD

160 F,85%

Equilibrium at T, RH
Source code

SSB3

Norm alized

Measured

Norm alized

Measured

Mean

113.90

113.93

91.67

91.80

Minim um

104.32

104.57

79.33

81.00

Maxim um

121.80

122.04

102.78

101.30

5.01

3.79

7.15

6.83

C.V.(%)

2% offset Strength
(ksi)

No. Specim ens


No. Prepreg Lots

19
3

Ultimate Strength not obtained

Page 64 of 238

19
3

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.31

Compression after Impact Properties

Material:

HEXCEL 8552 - IM7 UNI PREPREG

Resin content:

41.6 % vol

Fiber volum e:

58.40 % vol

Ply count:

24

Test m ethod:

SACMA SRM 2R-94

Norm alized by:

0.0072 in CPT

Compression After Impact


Com p. density:

1.58 [g/cc]

Gr/ Ep
HEXCEL 8552 - IM7 UNI PREPREG

[45,0,-45,90]3s

RTD (A)
Test Tem perature [F]

70F

Moisture Conditioning

dry

Equilibrium at T, RH
HFIKXXXXA

Source code

CAI

Norm alized

Measured

Mean

31.45

30.96

Minim um

30.17

29.53

Maxim um

33.80

33.43

C.V.(%)

4.16

4.65

Norm alized

Strength (ksi)
No. Specim ens

No. Prepreg Lots

Page 65 of 238

Measured

Norm alized

Measured

CAM-RP-2009-015 April 22, 2011 Revision A

2.3.32

Interlaminar Tension Properties

Material:

HEXCEL 8552 - IM7 UNI PREPREG

Resin content:

42.83 % w t

Fiber volum e:

57.17 % vol

Ply count:

22

Test m ethod:

ASTM D6415-99E1

Norm alized by:

NA

Interlaminar Tension
Gr/ Ep
HEXCEL 8552 - IM7 UNI PREPREG

Com p. density: 1.57 [g/cc]

[0]22

CTD (B)

RTD (A)

Test Tem perature [F]

-65F

70F

250F

Moisture Conditioning

dry

dry

equilibrium

HFIMXXXXB

HFIMXXXXA

HFIMXXXXD

ETW (D)

160 F,85%

Equilibrium at T, RH
Source code

Norm alized

ILT

Measured

Norm alized

Measured

Norm alized

Measured

Mean

11.96

11.04

6.46

Minim um

7.64

9.99

6.19

Maxim um

14.71

13.25

6.71

C.V.(%)

20.68

10.41

3.08

Strength (ksi)
No. Specim ens

No. Prepreg Lots

Page 66 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

3. Individual Test Charts


These charts combine all three batches of data and plot the minimum and maximum
modulus and strength range based on the test temperature.

Page 67 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

3.1 Longitudinal Tension Properties


Longitudinal Tension (LT) Strength -- Normalized

Conditioning
X Dry
O Wet

HEXCEL 8552 - IM7 UNI PREPREG


450
400

Strength (ksi)

350
300
250
200
150
100
50
0
-75

-25

25

75

125

175

225

275

Temperature (F)

Longitudinal Tension (LT) Modulus -- Normalized

Conditioning
X Dry
O Wet

HEXCEL 8552 - IM7 UNI PREPREG


30.0

Modulus (Msi)

25.0

20.0

15.0

10.0

5.0

0.0
-75

-25

25

75

125

Temperature (F)

Page 68 of 238

175

225

275

CAM-RP-2009-015 April 22, 2011 Revision A

3.2 Transverse Tension Properties


Transverse Tension (TT) Strength -- Measured

Conditioning
X Dry
O Wet

HEXCEL 8552 - IM7 UNI PREPREG


20
18
16

12
10
8
6
4
2
0
-100

-50

50

100

150

200

250

300

Temperature (F)

Transverse Tension (TT) Modulus -- Measured

Conditioning
X Dry
O Wet

HEXCEL 8552 - IM7 UNI PREPREG


7.5

Modulus (Msi)

Strength (ksi)

14

5.0

2.5

0.0
-100

-50

50

100

Temperature (F)

Page 69 of 238

150

200

250

300

CAM-RP-2009-015 April 22, 2011 Revision A

3.3 Longitudinal Compression Properties


Longitudinal Compression (LC) Modulus -- Normalized
HEXCEL 8552 - IM7 UNI PREPREG

Conditioning
X Dry
O Wet

40.0

Modulus (Msi)

30.0

20.0

10.0

0.0
-75

-25

25

75

125

Temperature (F)

Page 70 of 238

175

225

275

CAM-RP-2009-015 April 22, 2011 Revision A

3.4 Transverse Compression Properties


Transverse Compression (TC) Strength -- Measured
HEXCEL 8552 - IM7 UNI PREPREG
140
Conditioning
X Dry
O Wet

120

80
60
40
20
0
-100

-50

50

100

150

200

250

300

Temperature (F)

Transverse Compression (TC) Modulus -- Measured


HEXCEL 8552 - IM7 UNI PREPREG
10.0
Conditioning
X Dry
O Wet

7.5

Modulus (Msi)

Strength (ksi)

100

5.0

2.5

0.0
-100

-50

50

100

Temperature (F)

Page 71 of 238

150

200

250

300

CAM-RP-2009-015 April 22, 2011 Revision A

3.5 In-Plane Shear Properties


In-Plane Shear (IPS) Strength -- Measured At 5% Strain

Conditioning
X Dry
O Wet

HEXCEL 8552 - IM7 UNI PREPREG


20

10

0
0

50

100

150

200

250

300

Temperature (F)

In Plane Shear (IPS) Modulus -- Measured

Conditioning
X Dry
O Wet

HEXCEL 8552 - IM7 UNI PREPREG


2.00

1.50

Modulus (Msi)

Strength (ksi)

15

1.00

0.50

0.00
-100

-50

50

100

Temperature (F)

Page 72 of 238

150

200

250

300

CAM-RP-2009-015 April 22, 2011 Revision A

3.6 Unnotched Compression 0 Properties


Laminate Unnotched Compression 0 (UNC0) Strength -Normalized
HEXCEL 8552 - IM7 UNI PREPREG
150

Conditioning
X Dry
O Wet

100

75

50

25

0
-75

-25

25

75

125

175

225

275

Temperature (F)

Laminate Unnotched Compression 0 (UNC0) Modulus -Normalized


HEXCEL 8552 - IM7 UNI PREPREG
10

Conditioning
X Dry
O Wet

Modulus (Msi)

Strength (ksi)

125

0
-75

-25

25

75

125

Temperature (F)

Page 73 of 238

175

225

275

CAM-RP-2009-015 April 22, 2011 Revision A

3.7 Unnotched Tension 0 Properties

Laminate Unnotched Tension (UNT0) Strength -- Normalized


HEXCEL 8552 - IM7 UNI PREPREG
200
180
160

Strength (ksi)

140
120
100
80
60
40

Conditioning

20

X Dry
O Wet

0
-75

-25

25

75

125

175

225

275

Temperature (F)

Laminate Unnotched Tension (UNT0) Modulus -- Normalized


HEXCEL 8552 - IM7 UNI PREPREG
14.0
12.0

Modulus (Msi)

10.0
8.0
6.0
4.0
2.0

Conditioning
X Dry
O Wet

0.0
-75

-25

25

75

125

Temperature (F)

Page 74 of 238

175

225

275

CAM-RP-2009-015 April 22, 2011 Revision A

3.8 Lamina Short Beam Strength


Lamina Short Beam Strength (SBS) -- Measured

Conditioning
X Dry
O Wet

HEXCEL 8552 - IM7 UNI PREPREG


25.0

Strength (ksi)

20.0

15.0

10.0

5.0

0.0
-100

-50

50

100

Temperature (F)

Page 75 of 238

150

200

250

300

CAM-RP-2009-015 April 22, 2011 Revision A

3.9 Unnotched Tension 1 Properties

Laminate Unnotched Tension (UNT1) Strength -- Normalized


HEXCEL 8552 - IM7 UNI PREPREG
120

Strength (ksi)

100

80

60

40

Conditioning
20

X Dry
O Wet

0
-100

-50

50

100

150

200

250

300

Temperature (F)

Laminate Unnotched Tension (UNT1) Modulus -- Normalized


HEXCEL 8552 - IM7 UNI PREPREG
10.0

Modulus (Msi)

8.0

6.0

4.0

2.0

Conditioning
X Dry
O Wet

0.0
-100

-50

50

100

Temperature (F)

Page 76 of 238

150

200

250

300

CAM-RP-2009-015 April 22, 2011 Revision A

3.10 Unnotched Tension 2 Properties

Laminate Unnotched Tension (UNT2) Strength -- Normalized


HEXCEL 8552 - IM7 UNI PREPREG
100

60

40

20
Conditioning
X Dry
O Wet

0
-75

-25

25

75

125

175

225

275

Temperature (F)

Laminate Unnotched Tension (UNT2) Modulus -- Normalized


HEXCEL 8552 - IM7 UNI PREPREG
10.0

8.0

Modulus (Msi)

Strength (ksi)

80

6.0

4.0

2.0

Conditioning
X Dry
O Wet

0.0
-75

-25

25

75

125

Temperature (F)

Page 77 of 238

175

225

275

CAM-RP-2009-015 April 22, 2011 Revision A

3.11 Unnotched Tension 3 Properties


Laminate Unnotched Tension (UNT3) Strength -Normalized
HEXCEL 8552 - IM7 UNI PREPREG
240
200

Strength (ksi)

160
120
80
Conditioning

40

X Dry
O Wet

0
-100

-50

50

100

150

200

250

300

Temperature (F)

Laminate Unnotched Tension (UNT3) Modulus -Normalized


HEXCEL 8552 - IM7 UNI PREPREG
20.0

Modulus (Msi)

15.0

10.0

5.0

Conditioning
X Dry
O Wet

0.0
-100

-50

50

100

Temperature (F)

Page 78 of 238

150

200

250

300

CAM-RP-2009-015 April 22, 2011 Revision A

3.12 Unnotched Compression 1 Properties


Laminate Unnotched Compression 1 (UNC1) Strength -Normalized
HEXCEL 8552 - IM7 UNI PREPREG
100

60

40

20

Conditioning
X Dry
O Wet

0
0

50

100

150

200

250

300

Temperature (F)

Laminate Unnotched Compression 1 (UNC1) Modulus -Normalized


HEXCEL 8552 - IM7 UNI PREPREG

10

Modulus (Msi)

Strength (ksi)

80

Conditioning
X Dry
O Wet

0
0

50

100

150

Temperature (F)

Page 79 of 238

200

250

300

CAM-RP-2009-015 April 22, 2011 Revision A

3.13 Unnotched Compression 2 Properties


Laminate Unnotched Compression (UNC2) Strength -Normalized Strength
HEXCEL 8552 - IM7 UNI PREPREG

Conditioning
X Dry
O Wet

80

40

20

0
0

50

100

150

200

250

300

Temperature (F)

Laminate Unnotched Compression (UNC2) Modulus -Normalized


Conditioning

HEXCEL 8552 - IM7 UNI PREPREG

X Dry

O Wet

6.0
5.0

Modulus (Msi)

Strength (ksi)

60

4.0
3.0
2.0
1.0
0.0
0

50

100

150

Temperature (F)

Page 80 of 238

200

250

300

CAM-RP-2009-015 April 22, 2011 Revision A

3.14 Unnotched Compression 3 Properties


Laminate Unnotched Compression (UNC3) Strength -Normalized
HEXCEL 8552 - IM7 UNI PREPREG

Conditioning
X Dry
O Wet

160
140

100
80
60
40
20
0
0

50

100

150

200

250

300

Temperature (F)

Laminate Unnotched Compression (UNC3) Modulus -Normalized


HEXCEL 8552 - IM7 UNI PREPREG

Conditioning
X Dry
O Wet

14.0
12.0
10.0

Modulus (Msi)

Strength (ksi)

120

8.0
6.0
4.0
2.0
0.0
0

50

100

150

Temperature (F)

Page 81 of 238

200

250

300

CAM-RP-2009-015 April 22, 2011 Revision A

3.15 Laminate Short Beam Shear Properties

Laminate Short Beam Strength (LSBS) -- Measured


HEXCEL 8552 - IM7 UNI PREPREG

Conditioning
X Dry
O Wet

Strength (ksi)

14.0
12.0
10.0
8.0
6.0
4.0
2.0
0.0
0

50

100

150

Temperature (F)

Page 82 of 238

200

250

300

CAM-RP-2009-015 April 22, 2011 Revision A

3.16 Open Hole Tension 1 Properties


Open Hole Tension 1 (OHT1) Strength -- Normalized
HEXCEL 8552 - IM7 UNI PREPREG

Conditioning
X Dry
O Wet

80

Strength (ksi)

60

40

20

0
-75

-25

25

75

125

Temperature (F)

Page 83 of 238

175

225

275

CAM-RP-2009-015 April 22, 2011 Revision A

3.17 Open Hole Tension 2 Properties


Open Hole Tension 2 (OHT2) Strength -- Normalized
HEXCEL 8552 - IM7 UNI PREPREG
60

Conditioning
X Dry
O Wet

Strength (ksi)

50

40

30

20

10

0
-100

-50

50

100

Temperature (F)

Page 84 of 238

150

200

250

300

CAM-RP-2009-015 April 22, 2011 Revision A

3.18 Open Hole Tension 3 Properties


Open Hole Tension 3 (OHT3) Strength -- Normalized
HEXCEL 8552 - IM7 UNI PREPREG

Conditioning
X Dry
O Wet

140
120

Strength (ksi)

100
80
60
40
20
0
-100

-50

50

100

Temperature (F)

Page 85 of 238

150

200

250

300

CAM-RP-2009-015 April 22, 2011 Revision A

3.19 Filled-Hole Tension 1 Properties


Filled-Hole Tension 1 (FHT1) Strength -- Normalized

Conditioning
X Dry
O Wet

HEXCEL 8552 - IM7 UNI PREPREG


80

Strength (ksi)

60

40

20

0
-100

-50

50

100

Temperature (F)

Page 86 of 238

150

200

250

300

CAM-RP-2009-015 April 22, 2011 Revision A

3.20 Filled-Hole Tension 2 Properties


Filled-Hole Tension 2 (FHT2) Strength -- Normalized
HEXCEL 8552 - IM7 UNI PREPREG
60

Conditioning
X Dry
O Wet

50

Strength (ksi)

40

30

20

10

0
-75

-25

25

75

125

Temperature (F)

Page 87 of 238

175

225

275

CAM-RP-2009-015 April 22, 2011 Revision A

3.21 Filled-Hole Tension 3 Properties


Filled-Hole Tension 3 (FHT3) Strength -- Normalized

Conditioning
X Dry
O Wet

HEXCEL 8552 - IM7 UNI PREPREG


120

100

Strength (ksi)

80

60

40

20

0
-75

-25

25

75

125

Temperature (F)

Page 88 of 238

175

225

275

CAM-RP-2009-015 April 22, 2011 Revision A

3.22 Open Hole Compression 1 Properties


Open Hole Compression 1 (OHC1) Strength -- Normalized
HEXCEL 8552 - IM7 UNI PREPREG
60

Conditioning
X Dry
O Wet

Strength (ksi)

50

40

30

20

10

0
0

50

100

150

Temperature (F)

Page 89 of 238

200

250

300

CAM-RP-2009-015 April 22, 2011 Revision A

3.23 Open Hole Compression 2 Properties


Open Hole Compression 2 (OHC2) Strength -- Normalized
HEXCEL 8552 - IM7 UNI PREPREG

Conditioning
X Dry
O Wet

50

Strength (ksi)

40

30

20

10

0
0

50

100

150

Temperature (F)

Page 90 of 238

200

250

300

CAM-RP-2009-015 April 22, 2011 Revision A

3.24 Open Hole Compression 3 Properties

Open Hole Compression 3 (OHC3) Strength -- Normalized


HEXCEL 8552 - IM7 UNI PREPREG

Conditioning
X Dry

O Wet

80
70

Strength (ksi)

60
50
40
30
20
10
0
0

50

100

150

Temperature (F)

Page 91 of 238

200

250

300

CAM-RP-2009-015 April 22, 2011 Revision A

3.25 Filled-Hole Compression 1 Properties


Filled-Hole Compression 1 (FHC1) Strength -- Normalized

Conditioning
X Dry
O Wet

HEXCEL 8552 - IM7 UNI PREPREG


80

Strength (ksi)

60

40

20

0
0

50

100

150

Temperature (F)

Page 92 of 238

200

250

300

CAM-RP-2009-015 April 22, 2011 Revision A

3.26 Filled-Hole Compression 2 Properties


Filled-Hole Compression 2 (FHC2) Strength -- Normalized

Conditioning
X Dry
O Wet

HEXCEL 8552 - IM7 UNI PREPREG


60

Strength (ksi)

50

40

30

20

10

0
0

50

100

150

Temperature (F)

Page 93 of 238

200

250

300

CAM-RP-2009-015 April 22, 2011 Revision A

3.27 Filled-Hole Compression 3 Properties


Filled-Hole Compression 3 (FHC3) Strength-- Normalized
HEXCEL 8552 - IM7 UNI PREPREG

Conditioning
X Dry
O Wet

120

Strength (ksi)

100

80

60

40

20

0
0

50

100

150

Temperature (F)

Page 94 of 238

200

250

300

CAM-RP-2009-015 April 22, 2011 Revision A

3.28 Single Shear Bearing Strength1 Properties

Laminate Bearing Strength 1 (SSB1), 2% Offset -- Normalized


HEXCEL 8552 - IM7 UNI PREPREG
140
Conditioning
X Dry
O Wet

Strength (ksi)

120
100
80
60
40
20
0
0

50

100

150

Temperature (F)

200

250

300

3.29 Single Shear Bearing Strength 2 Properties


Laminate Bearing Strength (SSB2), 2% Offset -- Normalized
HEXCEL 8552 - IM7 UNI PREPREG
140

Conditioning
X Dry
O Wet

120

Strength (ksi)

100
80
60
40
20
0
0

50

100

150

Temperature (F)

Page 95 of 238

200

250

300

CAM-RP-2009-015 April 22, 2011 Revision A

3.30 Single Shear Bearing 3 Properties


Laminate Bearing Strength (SSB3), 2% Offset -- Normalized
HEXCEL 8552 - IM7 UNI PREPREG
140

Conditioning
X Dry
O Wet

120

Strength (ksi)

100
80
60
40
20
0
0

50

100

150

Temperature (F)

Page 96 of 238

200

250

300

CAM-RP-2009-015 April 22, 2011 Revision A

3.31 Compression Strength After Impact 1 Properties


Laminate Compression After Impact (CAI) Strength 1 -Normalized
HEXCEL 8552 - IM7 UNI PREPREG

Conditioning
X Dry

80

Strength (ksi)

60

40

20

0
0

50

100

150

Temperature (F)

Page 97 of 238

200

250

300

CAM-RP-2009-015 April 22, 2011 Revision A

3.32 Interlaminar Tension Properties


Laminate Curved Beam Strength (CBS) -Measured

Conditioning
X Dry
O Wet

HEXCEL 8552 - IM7 UNI PREPREG


500
450
400

CBS (lb)

350
300
250
200
150
100
50
0
-100

-50

50

100

150

200

250

300

Temperature (F)

Laminate Interlaminar Tension Strength (ILT) -Measured


HEXCEL 8552 - IM7 UNI PREPREG

Conditioning
X Dry

O Wet

ILT (ksi)

15.0
12.5
10.0
7.5
5.0
2.5
0.0
-100

-50

50

100

Temperature (F)

Page 98 of 238

150

200

250

300

CAM-RP-2009-015 April 22, 2011 Revision A

4. Raw Data

Page 99 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

4.1 Longitudinal Tension Properties


Longitudinal Tension Properties (LT) -- (CTD)
Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen Hexcel Hexcel Cure Prepreg Cure Cycle Strength
Number Batch #
Cycle
Lot #
#
[ksi]
HFIJA116B
A
M1
1
1
322.580
HFIJA117B
A
M1
1
1
344.115
HFIJA118B
A
M1
1
1
347.430
HFIJA119B
A
M1
1
1
357.922
HFIJA11AB
A
M1
1
1
340.005
HFIJA216B
A
M2
1
2
345.794
HFIJA217B
A
M2
1
2
357.079
HFIJA218B
A
M2
1
2
362.177
HFIJB116B
B
M1
2
1
372.292
HFIJB117B
B
M1
2
1
363.978
HFIJB118B
B
M1
2
1
372.635
HFIJB119B
B
M1
2
1
361.972
HFIJB11AB
B
M1
2
1
336.611
HFIJB216B
B
M2
2
2
356.433
HFIJB217B
B
M2
2
2
378.947
HFIJB218B
B
M2
2
2
357.856
HFIJC116B
C
M1
3
1
351.051
HFIJC117B
C
M1
3
1
350.530
HFIJC118B
C
M1
3
1
363.478
HFIJC216B
C
M2
3
2
342.104
HFIJC217B
C
M2
3
2
346.534
HFIJC218B
C
M2
3
2
349.867

Average 353.700
Standard Dev. 13.087
Coeff. of Var. [%] 3.700
Min. 322.580
Max. 378.947
Number of Spec.
22

Modulus
[Msi]
22.211
21.742
22.315
22.822
21.777
22.348
21.911
22.309
22.689
22.690
22.583
22.914
21.767
22.119
22.968
21.870
22.324
22.293
22.583
22.203
22.476
22.421

22.333
0.368
1.646
21.742
22.968
22

Poisson's Avg. Specimen


Ratio
Thickn. [in]
0.213
0.044
0.260
0.044
0.223
0.044
0.241
0.043
0.271
0.043
0.292
0.044
0.270
0.044
0.260
0.044
0.249
0.043
0.270
0.043
0.273
0.044
0.287
0.044
0.263
0.044
0.282
0.043
0.260
0.043
0.259
0.044
0.265
0.044
0.299
0.045
0.297
0.044
0.316
0.044
0.299
0.044
0.295
0.044

0.270
0.025
9.317
0.213
0.316
22

Page 100 of 238

# Plies in
Laminate
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6

Failure
Mode
LGM/SGM
LGM/SGM
XGM
XGM
LGM/SGM
LGM/SGM
LGM/SGM
LGM/SGM
XGM
XGM
XGM
XGM
LGM/SGM
XGM
LGM/SGM
XGM
XGM
XGM
XGM
SGM/LGM
XGM
XGM

Avg. tply Strengthnorm Modulusnorm


[in]
[ksi]
[Msi]
0.0073
325.692
22.425
0.0073
349.426
22.078
0.0073
351.451
22.573
0.0072
359.717
22.937
0.0072
341.186
21.852
0.0073
350.730
22.667
0.0073
364.105
22.342
0.0073
365.950
22.541
0.0072
369.851
22.540
0.0071
359.906
22.436
0.0073
376.229
22.801
0.0073
364.904
23.099
0.0073
341.805
22.103
0.0072
355.058
22.034
0.0072
379.970
23.030
0.0073
360.617
22.039
0.0073
356.197
22.651
0.0075
363.513
23.119
0.0074
373.715
23.219
0.0073
346.196
22.468
0.0073
352.015
22.832
0.0073
354.321
22.706

Average norm 0.0073


Standard Dev.norm
Coeff. of Var. [%]norm
Min.
0.0071
Max.
0.0075
Number of Spec.

357.389
12.620
3.531
325.692
379.970
22

22.568
0.387
1.717
21.852
23.219
22

CAM-RP-2009-015 April 22, 2011 Revision A

Longitudinal Tension Properties (LT) -- (CTD)


Normalized Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

Prepreg Lot #

Cure Cycle #

0
0

50

100

150

200

250

300

350

400

Longitudinal Tension Strength [ksi]

Longitudinal Tension Properties (LT) -- (CTD)


Normalized Modulus

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

0
0.0

5.0

10.0

15.0

Longitudinal Tension Modulus [Msi]

Page 101 of 238

20.0

25.0

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

Longitudinal Tension Properties (LT) -- (RTD)


Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen Hexcel Hexcel Cure Prepreg Cure Cycle Strength Modulus Poisson's Avg. Specimen # Plies in
Ratio
Number Batch #
Cycle
Lot #
#
[ksi]
[Msi]
Thickn. [in]
Laminate
HFIJA111A
A
M1
1
1
363.189 23.841
0.300
0.041
6
HFIJA112A
A
M1
1
1
374.161 23.658
0.283
0.043
6
HFIJA113A
A
M1
1
1
368.425 22.987
0.312
0.042
6
HFIJA211A
A
M2
1
2
370.513 24.377
0.356
0.042
6
HFIJA212A
A
M2
1
2
340.311 22.783
0.306
0.044
6
HFIJA213A
A
M2
1
2
348.015 22.918
0.325
0.044
6
HFIJB111A
B
M1
2
1
389.234 24.235
0.316
0.041
6
HFIJB112A
B
M1
2
1
381.337 23.404
0.308
0.043
6
HFIJB113A
B
M1
2
1
361.174 22.881
0.308
0.044
6
HFIJB211A
B
M2
2
2
401.224 24.332
0.315
0.039
6
HFIJB212A
B
M2
2
2
391.416 23.661
0.326
0.043
6
HFIJB213A
B
M2
2
2
359.564 23.361
0.319
0.044
6
HFIJC111A
C
M1
3
1
368.314 23.417
0.315
0.038
6
HFIJC112A
C
M1
3
1
378.487 24.196
0.354
0.041
6
HFIJC112A
C
M1
3
1
367.440 22.850
0.314
0.044
6
HFIJC211A
C
M2
3
2
372.821 23.749
0.306
0.040
6
HFIJC212A
C
M2
3
2
359.372 23.098
0.306
0.043
6
HFIJC213A
C
M2
3
2
384.495 23.488
0.312
0.044
6

Average 371.083
Standard Dev. 15.227
Coeff. of Var. [%] 4.103
Min. 340.311
Max. 401.224
Number of Spec.
18

23.513
0.533
2.267
22.783
24.377
18

0.316
0.017
5.450
0.283
0.356
18

Page 102 of 238

Failure
Mode
XGM
XGM
XGM
XGM
XGM
XGM
XGM
XGM
XGM
XGM
XGM
XGM
XGM
XGM
XGM
XGM
XGM
XGM

Avg. tply
[in]
0.0068
0.0071
0.0071
0.0070
0.0074
0.0074
0.0068
0.0072
0.0073
0.0065
0.0072
0.0073
0.0064
0.0069
0.0073
0.0067
0.0072
0.0073

Average norm 0.0070


Standard Dev. norm
Coeff. of Var. [%]norm
Min.
0.0064
Max.
0.0074
Number of Spec.

Strengthnorm
[ksi]
343.573
370.552
362.029
361.507
350.027
357.280
366.109
379.719
364.239
360.049
392.322
365.251
325.685
363.301
370.700
346.787
357.431
391.912

Modulusnorm
[Msi]
22.553
23.430
22.588
23.785
23.433
23.528
22.795
23.305
23.076
21.835
23.716
23.731
20.707
23.225
23.053
22.090
22.973
23.941

362.693
16.057
4.427
325.685
392.322
18

22.987
0.812
3.532
20.707
23.941
18

CAM-RP-2009-015 April 22, 2011 Revision A

Longitudinal Tension Properties (LT) -- (RTD)


Normalized Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

Prepreg Lot #

Cure Cycle #

3
2
2

0
0

50

100

150

200

250

300

350

400

450

Longitudinal Tension Strength [ksi]

Longitudinal Tension Properties (LT) -- (RTD)


Normalized Modulus

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

0
0.0

5.0

10.0

15.0

20.0

Longitudinal Tension Modulus [Msi]

Page 103 of 238

25.0

30.0

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A


Longitudinal Tension Properties (LT) -- (ETW)
Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Hexcel Hexcel Cure Prepreg Cure Cycle Strength Modulus Poisson's Avg. Specimen # Plies in
Ratio
Number
Batch #
Cycle
Lot #
#
[ksi]
[Msi]
Thickn. [in]
Laminate
HFIJA11BD
A
M1
1
1
331.955
23.036
0.431
0.044
6
HFIJA11CD
A
M1
1
1
301.489
23.846
0.435
0.043
6
HFIJA11DD*
A
M1
1
1
23.922
0.400
0.043
6
HFIJA11FD*
A
M1
1
1
23.564
0.396
0.043
6
HFIJA11GD
A
M1
1
1
256.064
26.174
0.470
0.042
6
HFIJA21BD
A
M2
1
2
351.042
23.311
0.428
0.044
6
HFIJA21CD
A
M2
1
2
330.067
24.009
0.217
0.044
6
HFIJA21DD
A
M2
1
2
241.828
23.023
0.189
0.044
6
HFIJA21ED
A
M2
1
2
337.005
23.286
0.359
0.044
6
HFIJA21FD
A
M2
1
2
352.193
22.694
0.334
0.045
6
HFIJB11BD**
B
M1
2
1
292.200
0.044
6
HFIJB11CD*
B
M1
2
1
24.475
0.443
0.044
6
HFIJB11DD*(**)
B
M1
2
1
23.469
0.043
6
HFIJB11ED
B
M1
2
1
343.230
23.122
0.353
0.044
6
HFIJB11FD
B
M1
2
1
345.534
23.158
0.365
0.044
6
HFIJB21BD*
B
M2
2
2
23.704
0.477
0.043
6
HFIJB21CD*
B
M2
2
2
24.072
0.491
0.043
6
HFIJB21DD*(**)
B
M2
2
2
24.203
0.043
6
HFIJB21ED*
B
M2
2
2
24.319
0.426
0.043
6
HFIJB21FD
B
M2
2
2
360.612
22.912
0.364
0.044
6
HFIJC11BD
C
M1
3
1
341.059
24.199
0.430
0.043
6
HFIJC11CD
C
M1
3
1
331.939
24.406
0.432
0.043
6
HFIJC11DD**
C
M1
3
1
308.746
23.422
0.043
6
HFIJC11ED
C
M1
3
1
24.622
0.412
0.044
6
HFIJC11FD
C
M1
3
1
366.864
23.363
0.363
0.044
6
HFIJC21BD
C
M2
3
2
23.810
0.409
0.043
6
HFIJC21CD
C
M2
3
2
23.857
0.440
0.044
6
HFIJC21DD**
C
M2
3
2
24.376
0.044
6
HFIJC21ED
C
M2
3
2
359.071
23.347
0.380
0.044
6
HFIJC21FD
C
M2
3
2
352.438
23.761
0.382
0.045
6
HIGH FREQUENCY OF UNACCEPTABLE FAILURES, ADHESIVE USED TO BOND TABS APPEARS TO BE INADEQUATE
*COUPONS EXPERIENCED AN UN ACCEPTABLE FAILURE AND THE STRENGTH WAS REMOVED
**MODULUS AND/OR POISSONS RATIO WAS REMOVED DUE TO NON-LINEARITY
Average 327.963
Standard Dev. 35.176
Coeff. of Var. [%] 10.726
Min. 241.828
Max. 366.864
Number of Spec.
18

23.775
0.693
2.917
22.694
26.174
29

0.393
0.070
17.820
0.189
0.491
25

Page 104 of 238

Failure
Mode
SGM
XGM
SGM / SIT
SGM / SIT
XGM
XGM
XGM
SGM
XGM
SGM
XGM
XGM / SIT
SGM/SIT
XGM
XGM
SIT
XGM / SIT
SGM / SIT
SGM / SIT
XGM
DGM
XGM
XGM
SGM / SIT
XGM
SGM / SIT
SGM / SIT
SGM / SIT
XGM
XGM

Average norm
Standard Dev.norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Avg. tply
[in]
0.0073
0.0072
0.0072
0.0071
0.0070
0.0073
0.0073
0.0073
0.0074
0.0075
0.0073
0.0073
0.0072
0.0074
0.0074
0.0072
0.0071
0.0072
0.0072
0.0073
0.0072
0.0072
0.0072
0.0073
0.0073
0.0072
0.0073
0.0073
0.0074
0.0075

0.0073

0.0070
0.0075

Strengthnorm Modulusnorm
[ksi]
[Msi]
335.541
23.285
303.117
23.975
23.793
23.382
250.235
25.578
357.814
23.761
335.288
24.389
244.533
23.281
347.016
23.977
366.596
23.622
296.033
24.702
23.496
352.102
23.719
355.532
23.828
23.558
23.738
24.063
24.356
365.481
23.222
342.901
24.329
331.555
24.378
309.103
23.449
24.831
373.234
23.769
23.930
24.023
24.790
369.461
24.023
367.531
24.778

333.504
38.823
11.641
244.533
373.234
18

24.001
0.557
2.321
23.222
25.578
29

CAM-RP-2009-015 April 22, 2011 Revision A

Longitudinal Tension Properties (LT) -- (ETW)


Normalized Strength
Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1

Prepreg Lot #

Cure Cycle #

0
0

50

100

150

200

250

300

350

400

450

500

550

600

Longitudinal Tension Strength [ksi]

Longitudinal Tension Properties (LT) -- (ETW)


Normalized Modulus

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2

1
1

0
0.0

5.0

10.0

15.0

20.0

Longitudinal Tension Modulus [Msi]

Page 105 of 238

25.0

30.0

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

4.2 Transverse Tension Properties


Transverse Tension Properties (TT) -- (CTD)
Strength & Modulus
HEXCEL 8552 - IM7 UNI PREPREG
Specimen
Number
HFIUA116B
HFIUA117B
HFIUA118B
HFIUA119B
HFIUA215B
HFIUA216B
HFIUA217B
HFIUA218B
HFIUB115B
HFIUB116B
HFIUB117B
HFIUB118B
HFIUB215B
HFIUB216B
HFIUB217B
HFIUC115B
HFIUC116B
HFIUC117B
HFIUC215B
HFIUC216B
HFIUC217B

Hexcel
Batch #
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M2
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
2
1
1
1
1
2
2
2
1
1
1
2
2
2

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength
[ksi]
9.090
9.524
11.192
10.574
9.812
10.127
10.039
10.215
9.082
8.976
7.881
9.574
7.876
9.734
8.869
9.790
10.432
10.014
9.632
9.535
9.681

Modulus
[Msi]
1.431
1.421
1.425
1.417
1.446
1.445
1.458
1.430
1.460
1.476
1.450
1.455
1.441
1.448
1.436
1.488
1.532
1.481
1.491
1.491
1.494

9.602
0.797
8.297
7.876
11.192
21

1.458
0.030
2.037
1.417
1.532
21

Page 106 of 238

Avg. Specimen
Thickn. [in]
0.081
0.081
0.082
0.082
0.081
0.081
0.081
0.082
0.078
0.078
0.078
0.080
0.079
0.079
0.078
0.081
0.076
0.080
0.080
0.080
0.079

# Plies in
Laminate
11
11
11
11
11
11
11
11
11
11
11
11
11
11
11
11
11
11
11
11
11

Avg. tply
[in]
0.0074
0.0074
0.0075
0.0075
0.0073
0.0074
0.0073
0.0075
0.0071
0.0071
0.0071
0.0072
0.0072
0.0072
0.0071
0.0074
0.0069
0.0072
0.0073
0.0073
0.0072

0.0073

0.0069
0.0075

Failure
Mode
LGM
LAT
LAB
LAT/LWB
LGM
LGM/LAT
LGM
LGM
LAB
LAB
LAB
LGM
LWT
LWT
LAT
LWB
LAT
LAB
LWT
LWT
LGM

CAM-RP-2009-015 April 22, 2011 Revision A

Transverse Tension Properties (TT) -- (CTD)


Measured Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
2

0
0

10

15

20

25

30

Transverse Tension Strength [ksi]

Transverse Tension Properties (TT) -- (CTD)


Measured Modulus

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
2

0
0.0

2.0

Transverse Tension Modulus [Msi]

Page 107 of 238

4.0

Prepreg Lot #

Cure Cycle #

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

Transverse Tension Properties (TT) -- (RTD)


Strength & Modulus
HEXCEL 8552 - IM7 UNI PREPREG
Specimen
Number
HFIUA111A
HFIUA112A
HFIUA113A
HFIUA114A
HFIUA115A
HFIUA212A
HFIUA213A
HFIUA214A
HFIUB112A
HFIUB113A
HFIUB114A
HFIUB212A
HFIUB213A
HFIUB214A
HFIUC111A
HFIUC112A
HFIUC113A
HFIUC211A
HFIUC212A
HFIUC213A

Hexcel Hexcel Cure Prepreg


Batch #
Cycle
Lot #
A
M1
1
A
M1
1
A
M1
1
A
M1
1
A
M1
1
A
M2
1
A
M2
1
A
M2
1
B
M1
2
B
M1
2
B
M1
2
B
M2
2
B
M2
2
B
M2
2
C
M1
3
C
M1
3
C
M1
3
C
M2
3
C
M2
3
C
M2
3

Cure Cycle
#
1
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength Modulus Avg. Specimen # Plies in Avg. tply


[ksi]
[Msi]
Thickn. [in]
Laminate
[in]
9.972
1.350
0.075
11
0.0068
10.801
1.263
0.083
11
0.0076
8.514
1.271
0.083
11
0.0075
9.987
1.262
0.081
11
0.0074
10.145
1.262
0.082
11
0.0074
9.127
1.276
0.082
11
0.0075
9.942
1.214
0.082
11
0.0075
9.195
1.268
0.081
11
0.0073
8.853
1.269
0.079
11
0.0072
8.946
1.270
0.080
11
0.0072
9.246
1.282
0.078
11
0.0071
7.397
1.295
0.080
11
0.0073
7.967
1.307
0.079
11
0.0072
8.132
1.315
0.078
11
0.0071
9.860
1.359
0.078
11
0.0071
8.791
1.333
0.080
11
0.0073
10.109
1.348
0.080
11
0.0072
8.929
1.401
0.075
11
0.0068
10.430
1.307
0.081
11
0.0074
9.381
1.307
0.080
11
0.0073

9.286
0.879
9.470
7.397
10.801
20

1.298
0.044
3.365
1.214
1.401
20

Page 108 of 238

0.0073

0.0068
0.0076

Failure
Mode
LAT
LWT
LGM
LAB
LAT
LGM
LGM
LGM
LGM
LWB
LWB
LGM
LAB
LAT
LGM
LAT
LAT
LGM
LGM
LAT

CAM-RP-2009-015 April 22, 2011 Revision A

Transverse Tension Properties (TT) -- (RTD)


Measured Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
2

Prepreg Lot #

Cure Cycle #

0
0

10

15

20

25

30

Transverse Tension Strength [ksi]

Transverse Tension Properties (TT) -- (RTD)


Measured Modulus

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
2

0
0.0

1.0

2.0

3.0

Transverse Tension Modulus [Msi]

Page 109 of 238

4.0

5.0

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

Transverse Tension Properties (TT) -- (ETW)


Strength & Modulus
HEXCEL 8552 - IM7 UNI PREPREG
Specimen Hexcel Hexcel Cure Prepreg
Number
Batch #
Cycle
Lot #
HFIUA11AD
A
M1
1
HFIUA11BD
A
M1
1
HFIUA11CD
A
M1
1
HFIUA11DD
A
M1
1
HFIUA219D
A
M2
1
HFIUA21BD
A
M2
1
HFIUA21CD
A
M2
1
HFIUB119D
B
M1
2
HFIUB11AD
B
M1
2
HFIUB11BD
B
M1
2
HFIUB218D
B
M2
2
HFIUB219D
B
M2
2
HFIUB21BD
B
M2
2
HFIUC118D
C
M1
3
HFIUC119D
C
M1
3
HFIUC11AD
C
M1
3
HFIUC218D
C
M2
3
HFIUC219D
C
M2
3
HFIUC21BD
C
M2
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength
[ksi]
3.879
3.265
3.362
3.486
3.337
3.236
3.649
3.464
3.269
3.915
3.566
3.277
3.478
3.756
3.323
3.721
3.633
3.223
3.408

3.487
0.219
6.281
3.223
3.915
19

Modulus Avg. Specimen # Plies in


[Msi]
Thickn. [in]
Laminate
0.891
0.076
11
0.791
0.082
11
0.769
0.081
11
0.778
0.080
11
0.786
0.081
11
0.759
0.083
11
0.789
0.082
11
0.804
0.080
11
0.828
0.076
11
0.890
0.072
11
0.798
0.079
11
0.765
0.080
11
0.846
0.073
11
0.850
0.080
11
0.811
0.081
11
0.884
0.075
11
0.793
0.080
11
0.796
0.081
11
0.789
0.081
11

0.811
0.042
5.149
0.759
0.891
19

Page 110 of 238

Avg. tply
[in]
0.0069
0.0074
0.0074
0.0073
0.0074
0.0075
0.0075
0.0073
0.0069
0.0065
0.0072
0.0073
0.0067
0.0073
0.0074
0.0068
0.0073
0.0074
0.0074

0.0072

0.0065
0.0075

Failure
Mode
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM

CAM-RP-2009-015 April 22, 2011 Revision A

Transverse Tension Properties (TT) -- (ETW)


Measured Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
2

Prepreg Lot #

Cure Cycle #

0
0

10

Transverse Tension Strength [ksi]

Transverse Tension Properties (TT) -- (ETW)


Measured Modulus

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
2

0
0.0

1.0

2.0

Transverse Tension Modulus [Msi]

Page 111 of 238

3.0

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

4.3 Longitudinal Compression Properties


Longitudinal Compression Properties (LC) -- (CTD)
Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen Hexcel Hexcel Cure Prepreg Cure Cycle Modulus
Number
Batch #
Cycle
Lot #
#
[Msi]
HFILA115B
A
M1
1
1
20.088
HFILA116B
A
M1
1
1
20.307
HFILA117B
A
M1
1
1
21.024
HFILA118B
A
M1
1
1
20.317
HFILA119B
A
M1
1
1
20.148
HFILA215B*
A
M2
1
2
HFILA216B*
A
M2
1
2
HFILA217B*
A
M2
1
2
HFILB115B
B
M1
2
1
20.258
HFILB116B
B
M1
2
1
20.915
HFILB117B
B
M1
2
1
20.967
HFILB215B
B
M2
2
2
21.136
HFILB216B
B
M2
2
2
19.971
HFILB217B
B
M2
2
2
19.049
HFILB218B
B
M2
2
2
20.368
HFILB219B
B
M2
2
2
20.413
HFILC115B
C
M1
3
1
20.998
HFILC116B
C
M1
3
1
21.288
HFILC117B
C
M1
3
1
21.291
HFILC118B
C
M1
3
1
20.974
HFILC215B
C
M2
3
2
21.130
HFILC216B
C
M2
3
2
19.562
HFILC217B
C
M2
3
2
20.370
Specimens have uneven grip marks so values are removed
Average 20.529
Standard Dev.
0.603
Coeff. of Var. [%]
2.935
Min. 19.049
Max. 21.291
Number of Spec.
20

Poisson's
Ratio
0.451
0.404
0.287
0.335
0.364

0.362
0.335
0.289
0.331
0.466
0.305
0.447
0.354
0.411
0.351
0.355
0.378
0.372
0.301
0.332

Avg. Specimen # Plies in


Thickn. [in]
Laminate
0.104
14
0.104
14
0.102
14
0.101
14
0.101
14
14
14
14
0.107
14
0.108
14
0.107
14
0.095
14
0.094
14
0.094
14
0.093
14
0.093
14
0.105
14
0.104
14
0.103
14
0.102
14
0.105
14
0.104
14
0.103
14

0.362
0.052
14.482
0.287
0.466
20

Average norm
Standard Dev.norm
Coeff. of Var. [%]norm

Avg. tply
[in]
0.0074
0.0074
0.0073
0.0072
0.0072

Modulusnorm
[Msi]
20.709
20.925
21.375
20.384
20.201

0.0076
0.0077
0.0077
0.0068
0.0067
0.0067
0.0067
0.0067
0.0075
0.0074
0.0074
0.0073
0.0075
0.0074
0.0073

21.484
22.392
22.291
19.952
18.584
17.796
18.866
18.901
21.873
21.989
21.745
21.280
21.916
20.099
20.767

0.0072

20.676
1.323
6.396
17.796
22.392
20

0.0067
0.0077

Longitudinal Compression Properties (LC) -- (CTD)


Normalized Modulus
HEXCEL 8552 - IM7 UNI PREPREG
3
Cure Cycle #

2
2

1
1

0
0.0

2.0

4.0

6.0

8.0

10.0

12.0

14.0

16.0

18.0

20.0

22.0

24.0

26.0

28.0

Longitudinal Compression Modulus [Msi]

Page 112 of 238

30.0

32.0

34.0

36.0

38.0

40.0

Prepreg Lot #

Cure Cycle #

Prepreg Lot #

CAM-RP-2009-015 April 22, 2011 Revision A

Longitudinal Compression Properties (LC) -- (RTD)


Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen Hexcel Hexcel Cure Prepreg Cure Cycle Modulus Poisson's
Number
Batch #
Cycle
Lot #
#
[Msi]
Ratio
HFILA111A*
A
M1
1
1
HFILA112A
A
M1
1
1
20.248
0.352
HFILA113A
A
M1
1
1
19.799
0.366
HFILA114A
A
M1
1
1
19.957
0.372
HFILA211A*
A
M2
1
2
HFILA212A*
A
M2
1
2
HFILA213A
A
M2
1
2
20.235
0.360
HFILB111A
B
M1
2
1
20.667
0.423
HFILB112A
B
M1
2
1
20.777
0.335
HFILB113A
B
M1
2
1
20.230
0.310
HFILB211A*
B
M2
2
2
HFILB212A
B
M2
2
2
20.534
0.335
HFILB213A
B
M2
2
2
20.256
0.310
HFILC111A
C
M1
3
1
20.888
0.332
HFILC112A
C
M1
3
1
20.446
0.369
HFILC113A
C
M1
3
1
20.737
0.393
HFILC211A
C
M2
3
2
20.745
0.358
HFILC212A
C
M2
3
2
20.430
0.365
HFILC213A
C
M2
3
2
20.658
0.365
Specimens have thickness taper on edge of coupon, so values were removed.
Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

20.440
0.317
1.549
19.799
20.888
15

Avg. Specimen
Thickn. [in]
0.095
0.101
0.103

0.093
0.108
0.109
0.108
0.089
0.093
0.088
0.096
0.102
0.094
0.100
0.103

0.356
0.029
8.278
0.310
0.423
15

# Plies in
Laminate
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14

Avg. tply
[in]

Modulusnorm
[Msi]

0.0068
0.0072
0.0074

18.993
19.839
20.439

0.0067
0.0077
0.0078
0.0077

18.742
22.099
22.429
21.618

0.0064
18.188
0.0066
18.702
0.0063
18.325
0.0069
19.526
0.0073
20.898
0.0067
19.445
0.0071
20.221
0.0074
21.088
near edge thickness taper

Average norm
Standard Dev.norm
Coeff. of Var. [%]norm

0.0071

20.037
1.365
6.810
18.188
22.429
15

0.0063
0.0078

Longitudinal Compression Properties (LC) -- (RTD)


Normalized Modulus
HEXCEL 8552 - IM7 UNI PREPREG
3
3
Cure Cycle #
Prepreg Lot #

0
0.0

2.0

4.0

6.0

8.0

10.0

12.0

14.0

16.0

18.0

20.0

22.0

24.0

26.0

28.0

Longitudinal Compression Modulus [Msi]

Page 113 of 238

30.0

32.0

34.0

36.0

38.0

40.0

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

Longitudinal Compression Properties (LC) -- (ETD)


Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen Hexcel Hexcel Cure Prepreg Cure Cycle Modulus Poisson's
Number
Batch #
Cycle
Lot #
#
[Msi]
Ratio
HFILA1ROC
A
M1
1
1
19.773
0.385
HFILA1RPC
A
M1
1
1
19.556
0.372
HFILA1RQC
A
M1
1
1
19.564
0.369
HFILA1RRC
A
M1
1
1
19.375
0.394
HFILA218C
A
M2
1
2
19.534
0.396
HFILA219C
A
M2
1
2
19.663
0.373
HFILA21DC
A
M2
1
2
19.759
0.354
HFILB118C
B
M1
2
1
20.919
0.401
HFILB119C
B
M1
2
1
20.483
0.391
HFILB11DC
B
M1
2
1
19.776
0.338
HFILB21DC
B
M2
2
2
19.877
0.357
HFILB2RMC*
B
M2
2
2
HFILB2RNC*
B
M2
2
2
HFILC11DC
C
M1
3
1
20.062
0.381
HFILC114C
C
M1
3
1
20.358
0.360
HFILC1RPC
C
M1
3
1
20.297
0.376
HFILC21DC
C
M2
3
2
19.978
0.357
HFILC218C
C
M2
3
2
20.084
0.366
HFILC219C
C
M2
3
2
20.913
0.396
Specimens have thickness taper on edge of coupon, so values were removed.
Average 19.998
0.374
Standard Dev. 0.463
0.018
Coeff. of Var. [%] 2.313
4.781
Min. 19.375
0.338
Max. 20.919
0.401
Number of Spec.
17
17

Avg. Specimen
Thickn. [in]
0.101
0.102
0.103
0.104
0.095
0.094
0.097
0.107
0.107
0.108
0.094
0.084
0.090
0.104
0.104
0.105
0.105
0.102
0.102

# Plies in
Laminate
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14

Avg. tply
[in]
0.0072
0.0073
0.0074
0.0075
0.0068
0.0067
0.0069
0.0076
0.0076
0.0077
0.0067

Modulusnorm
[Msi]
19.883
19.753
19.990
20.048
18.404
18.369
18.923
22.123
21.722
21.271
18.493

0.0074
0.0074
0.0075
0.0075
0.0073
0.0073

20.756
21.031
21.092
20.754
20.386
21.190

0.0073

20.246
1.165
5.757
18.369
22.123
17

Average norm
Standard Dev.norm
Coeff. of Var. [%]norm

0.0067
0.0077

Longitudinal Compression Properties (LC) -- (ETD)


Normalized Modulus
HEXCEL 8552 - IM7 UNI PREPREG
3
3
Prepreg Lot #

2
2

1
1

0
0.0

2.0

4.0

6.0

8.0

10.0

12.0

14.0

16.0

18.0

20.0

22.0

24.0

26.0

28.0

Longitudinal Compression Modulus [Msi]

Page 114 of 238

30.0

32.0

34.0

36.0

38.0

40.0

Prepreg Lot #

Cure Cycle #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

Longitudinal Compression Properties (LC) -- (ETW)


Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen Hexcel Hexcel Cure Prepreg Cure Cycle Modulus Poisson's Avg. Specimen # Plies in
Number
Batch #
Cycle
Lot #
#
Laminate
HFILA11GD
A
M1
1
1
19.933
0.379
0.100
14
HFILA11HD
A
M1
1
1
20.124
0.409
0.094
14
HFILA11ID
A
M1
1
1
19.455
0.335
0.103
14
HFILA21ED
A
M2
1
2
19.539
0.351
0.097
14
HFILA21FD
A
M2
1
2
19.888
0.342
0.097
14
HFILA21GD
A
M2
1
2
19.229
0.344
0.094
14
HFILB11ED*
B
M1
2
1
20.777
0.346
0.106
14
HFILB11FD*
B
M1
2
1
20.158
0.336
0.101
14
HFILB11GD*
B
M1
2
1
21.348
0.359
0.095
14
HFILB21ED
B
M2
2
1
20.248
0.341
0.094
14
HFILB21FD
B
M2
2
2
20.131
0.341
0.095
14
HFILB21GD
B
M2
2
2
26.641
0.412
0.093
14
HFILC11ED
C
M1
3
1
20.987
0.322
0.105
14
HFILC11FD
C
M1
3
1
20.445
0.329
0.103
14
HFILC11GD
C
M1
3
1
24.827
0.466
0.098
14
HFILC11HD
C
M1
3
1
20.498
0.362
0.093
14
HFILC11ID
C
M1
3
1
17.674
0.355
0.089
14
HFILC21ED
C
M2
3
2
20.085
0.310
0.105
14
HFILC21FD
C
M2
3
2
20.112
0.352
0.103
14
HFILC21GD
C
M2
3
2
19.741
0.324
0.099
14
HFILA11JD
A
M1
1
1
19.858
0.392
0.105
14
HFILA11KD
A
M1
1
1
19.580
0.416
0.106
14
HFILA1RMD
A
M1
1
1
19.955
0.529
0.101
14
HFILA1RND
A
M1
1
2
20.050
0.412
0.101
14
HFILA21HD*
A
M2
1
2
14
HFILA214D
A
M2
1
2
26.053
0.509
0.096
14
HFILB11HD
B
M1
2
1
20.996
0.379
0.107
14
HFILB11ID
B
M1
2
1
20.077
0.399
0.109
14
HFILB114D
B
M1
2
1
19.972
0.390
0.108
14
HFILB21ID*
B
M2
2
1
14
HFILB214D
B
M2
2
2
20.822
0.376
0.095
14
HFILC1RMD
C
M1
3
1
21.213
0.451
0.096
14
HFILC1RND
C
M1
3
1
20.134
0.403
0.101
14
HFILC1ROD
C
M1
3
1
20.821
0.446
0.105
14
HFILC21HD
C
M2
3
1
20.601
0.370
0.092
14
HFILC21ID
C
M2
3
1
20.282
0.402
0.094
14
HFILC214D
C
M2
3
2
20.436
0.413
0.104
14
*Specimens have thickness taper on edge of coupon, so values were removed.
DATA WAS NOT REPORTED FOR HFILA11FD DUE TO BAD FAILURE
HFILB21HD STRAIN GAGE WENT BAD HENCE THE MODULUS AND POISSONS RATIO WAS REMOVED
Shaded portion was originally tested with improper strain gage adhesive
Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

20.648
1.754
8.494
17.674
26.641
35

0.383
0.051
13.446
0.310
0.529
35

Page 115 of 238

0.099
Average norm
0.005
Standard Dev.norm
5.383 Coeff. of Var. [%]norm
0.089
0.109
35

Avg. tply
[in]
0.0071
0.0067
0.0074
0.0069
0.0069
0.0067
0.0076
0.0072
0.0068
0.0067
0.0068
0.0066
0.0075
0.0074
0.0070
0.0066
0.0064
0.0075
0.0074
0.0071
0.0075
0.0075
0.0072
0.0072

Modulusnorm
[Msi]
19.758
18.723
19.863
18.793
19.040
17.865
21.880
20.188
20.077
18.899
18.973
24.518
21.833
20.939
24.195
18.847
15.614
20.925
20.558
19.330
20.744
20.499
20.070
20.120

0.0068
0.0076
0.0078
0.0077

24.761
22.187
21.687
21.349

0.0068
0.0069
0.0072
0.0075
0.0066
0.0067
0.0075

19.586
20.261
20.220
21.692
18.778
18.897
21.159

0.0071

20.367
1.834
9.005
15.614
24.761
35

0.0064
0.0078
35

CAM-RP-2009-015 April 22, 2011 Revision A

Longitudinal Compression Properties (LC) -- (ETW)


Normalized Modulus
HEXCEL 8552 - IM7 UNI PREPREG
3
3
Prepreg Lot #

2
2

1
1

0
0.0

2.0

4.0

6.0

8.0

10.0

12.0

14.0

16.0

18.0

20.0

22.0

24.0

26.0

Longitudinal Compression Modulus [Msi]

Page 116 of 238

28.0

30.0

32.0

34.0

36.0

38.0

40.0

Prepreg Lot #

Cure Cycle #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

4.4 Transverse Compression Properties


Transverse Compression Properties (TC) -- (CTD)
Strength & Modulus
HEXCEL 8552 - IM7 UNI PREPREG
Specimen Hexcel Hexcel Cure Prepreg Cure Cycle Strength Modulus
Number
Batch #
Cycle
Lot #
#
[ksi]
[Msi]
HFIZA116B
A
M1
1
1
59.383
1.609
HFIZA117B
A
M1
1
1
61.395
1.373
HFIZA118B
A
M1
1
1
55.734
1.264
HFIZA119B
A
M1
1
1
57.917
1.336
HFIZA11AB
A
M1
1
1
57.316
1.635
HFIZA217B
A
M2
1
2
55.031
1.565
HFIZA218B
A
M2
1
2
51.915
1.569
HFIZA219B
A
M2
1
2
58.191
1.694
HFIZB115B
B
M1
2
1
53.205
1.592
HFIZB116B*
B
M1
2
1
55.667
1.590
HFIZB117B*
B
M1
2
1
54.068
1.490
HFIZB216B
B
M2
2
2
56.320
1.494
HFIZB217B
B
M2
2
2
56.367
1.543
HFIZB218B
B
M2
2
2
50.774
1.470
HFIZC117B
C
M1
3
1
55.515
1.551
HFIZC118B
C
M1
3
1
51.129
1.463
HFIZC119B
C
M1
3
1
50.408
1.413
HFIZC216B
C
M2
3
2
54.186
1.662
HFIZC217B
C
M2
3
2
55.937
1.696
HFIZC218B
C
M2
3
2
55.812
1.570
* Bad failures occured secondary to the first failure
Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

55.313
2.873
5.194
50.408
61.395
20

1.529
0.117
7.641
1.264
1.696
20

Poisson's
Ratio
0.027
0.021
0.028
0.027
0.031
0.025
0.032
0.030
0.027
0.031
0.028
0.026
0.029
0.029
0.028
0.018
0.031
0.027
0.032
0.029

0.028
0.004
12.744
0.018
0.032
20

Page 117 of 238

Avg. Specimen
Thickn. [in]
0.099
0.099
0.100
0.100
0.100
0.100
0.100
0.101
0.102
0.101
0.101
0.099
0.099
0.100
0.102
0.102
0.103
0.101
0.100
0.102

# Plies in
Laminate
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14

Avg. tply
[in]
0.0071
0.0071
0.0071
0.0072
0.0072
0.0071
0.0072
0.0072
0.0073
0.0072
0.0072
0.0071
0.0071
0.0071
0.0073
0.0073
0.0073
0.0072
0.0072
0.0073

0.0072

0.0071
0.0073

Failure
Mode
HAT/HIT
HGM
HGM/HIB
HGM/HIB/HIT
HAT
HGM
HGM
HGM
HGM
HGM/HAB/HIB
HGM/HIT/HIB
HGM
HGM
HGM
HGM
HGM
HGM
HAT
HAT
HAT

CAM-RP-2009-015 April 22, 2011 Revision A

Transverse Compression Properties (TC) -- (CTD)


Measured Strength
HEXCEL 8552 - IM7 UNI PREPREG
3
3

Prepreg Lot #

2
2

Prepreg Lot #

Cure Cycle #

Cure Cycle #

0
0

10

20

30

40

50

60

70

80

90

100

Transverse Compression Strength [ksi]

Transverse Compression Properties (TC) -- (CTD)


Measured Modulus
HEXCEL 8552 - IM7 UNI PREPREG
3
3

Prepreg Lot #

2
2

0
0.0

2.0

Transverse Compression Modulus [Msi]

Page 118 of 238

4.0

Prepreg Lot #

Cure Cycle #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

Transverse Compression Properties (TC) -- (RTD)


Strength & Modulus
HEXCEL 8552 - IM7 UNI PREPREG
Specimen Hexcel Hexcel Cure Prepreg Cure Cycle Strength Modulus Poisson's Avg. Specimen # Plies in
Number
Batch #
Cycle
Lot #
#
[ksi]
[Msi]
Ratio
Thickn. [in]
Laminate
HFIZA111A
A
M1
1
1
46.403
1.664
0.022
0.089
14
HFIZA112A
A
M1
1
1
43.300
1.594
0.025
0.094
14
HFIZA113A
A
M1
1
1
43.323
1.324
0.023
0.099
14
HFIZA114A
A
M1
1
1
43.633
1.423
0.024
0.101
14
HFIZA115A
A
M1
1
1
41.892
1.419
0.022
0.101
14
HFIZA212A
A
M2
1
2
39.235
1.424
0.025
0.097
14
HFIZA213A
A
M2
1
2
40.716
1.395
0.024
0.101
14
HFIZA214A
A
M2
1
2
41.630
1.255
0.022
0.103
14
HFIZB112A
B
M1
2
1
38.789
1.419
0.022
0.098
14
HFIZB113A
B
M1
2
1
40.581
1.408
0.025
0.102
14
HFIZB114A
B
M1
2
1
38.857
1.249
0.020
0.103
14
HFIZB213A*
B
M2
2
2
40.340
1.378
0.023
0.102
14
HFIZB214A*
B
M2
2
2
41.291
1.419
0.026
0.101
14
HFIZB215A
B
M2
2
2
40.150
1.379
0.022
0.100
14
HFIZC112A
C
M1
3
1
40.681
1.352
0.022
0.099
14
HFIZC113A
C
M1
3
1
40.902
1.411
0.023
0.103
14
HFIZC114A
C
M1
3
1
41.630
1.387
0.025
0.104
14
HFIZC213A
C
M2
3
2
41.218
1.465
0.025
0.103
14
HFIZC214A
C
M2
3
2
43.627
1.386
0.027
0.103
14
HFIZC215A
C
M2
3
2
40.524
1.422
0.023
0.102
14
* Bad failures occured secondary to the first failure
Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

41.436
1.864
4.497
38.789
46.403
20

1.409
0.093
6.634
1.249
1.664
20

0.024
0.002
7.615
0.020
0.027
20

Page 119 of 238

Avg. tply
[in]
0.0063
0.0067
0.0071
0.0072
0.0072
0.0069
0.0072
0.0074
0.0070
0.0073
0.0073
0.0073
0.0072
0.0072
0.0071
0.0074
0.0074
0.0073
0.0074
0.0073

0.0072

0.0063
0.0074

Failure
Mode
BAB
BAB
BAB
BAB
BAB
HGM
BGM
HGM
BGM
BGM
BGM
HGM / HIT
HGM / HIT
HGM
HGM
HGM
HAT
HAB
BGM
BAT

CAM-RP-2009-015 April 22, 2011 Revision A

Transverse Compression Properties (TC) -- (RTD)


Measured Strength
HEXCEL 8552 - IM7 UNI PREPREG
3
3
Cure Cycle #
Prepreg Lot #

0
0

10

20

30

40

50

60

70

80

90

100

Transverse Compression Strength [ksi]

Transverse Compression Properties (TC) -- (RTD)


Measured Modulus
HEXCEL 8552 - IM7 UNI PREPREG
3
3

Prepreg Lot #

2
2

0
0.0

2.0

Transverse Compression Modulus [Msi]

Page 120 of 238

4.0

Prepreg Lot #

Cure Cycle #

Cure Cycle #

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

Transverse Compression Properties (TC) -- (ETW)


Strength & Modulus
HEXCEL 8552 - IM7 UNI PREPREG
Specimen
Hexcel Hexcel Cure Prepreg
Number
Batch #
Cycle
Lot #
HFIZA11BD
A
M1
1
HFIZA11CD
A
M1
1
HFIZA11DD
A
M1
1
HFIZA11ED
A
M1
1
HFIZA11FD
A
M1
1
HFIZA21AD
A
M2
1
HFIZA21BD
A
M2
1
HFIZA21CD
A
M2
1
HFIZA21ED
A
M2
1
HFIZB119D
B
M1
2
HFIZB11AD
B
M1
2
HFIZB11BD
B
M1
2
HFIZB11CD
B
M1
2
HFIZB219D
B
M2
2
HFIZB21AD
B
M2
2
HFIZB21BD
B
M2
2
HFIZB21CD
B
M2
2
HFIZC11AD
C
M1
3
HFIZC11BD
C
M1
3
HFIZC11CD
C
M1
3
HFIZC11FD
C
M1
3
HFIZC21AD
C
M2
3
HFIZC21BD
C
M2
3
HFIZC21CD
C
M2
3
HFIZC21DD
C
M2
3
HFIZA215D*
A
M1
1
HFIZA211D*
A
M1
1
HFIZA216D*
A
M1
1
HFIZB111D*
B
M1
2
HFIZB118D*
B
M1
2
HFIZC111D*
C
M1
3
HFIZC115D*
C
M1
3
HFIZC116D*
C
M1
3
HFIZC219D*
C
M2
3
* Modulus only coupons

Cure Cycle
#
1
1
1
1
1
2
2
2
2
1
1
1
1
2
2
2
2
1
1
1
1
2
2
2
2
1
1
1
1
1
1
1
1
2

Strength
[ksi]
20.168
20.118
17.022
19.857
17.733
18.535
18.757
18.574
20.702
17.259
16.779
18.688
19.599
19.524
19.676
18.781
20.132
18.895
18.186
18.838
20.021
18.681
19.567
19.370
20.011

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

19.019
1.041
5.474
16.779
20.702
25

Modulus*
[Msi]

Poisson's
Ratio

1.224
1.346
1.119
1.184
1.227
1.249
1.164
1.031
1.087

0.018
0.018
0.017
0.017
0.016
0.018
0.018
0.017
0.020

1.181
0.094
7.994
1.031
1.346
9

0.018
0.001
7.577
0.016
0.020
9

Page 121 of 238

Avg. Specimen
Thickn. [in]
0.099
0.100
0.100
0.102
0.102
0.101
0.101
0.100
0.102
0.101
0.101
0.100
0.101
0.100
0.100
0.100
0.100
0.103
0.102
0.102
0.104
0.102
0.102
0.100
0.101
0.103
0.087
0.101
0.091
0.100
0.092
0.104
0.103
0.102

# Plies in
Laminate
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14
14

Avg. tply
[in]
0.0071
0.0071
0.0072
0.0073
0.0073
0.0072
0.0072
0.0072
0.0073
0.0072
0.0072
0.0072
0.0072
0.0071
0.0071
0.0071
0.0072
0.0073
0.0073
0.0073
0.0074
0.0073
0.0073
0.0072
0.0072
0.0074
0.0062
0.0072
0.0065
0.0072
0.0066
0.0074
0.0073
0.0073

0.007

0.006
0.007
34

Failure
Mode
HGM
HGM
HGM
HGM
HGM
HGM
HGM
HGM
HGM
HGM
HGM
HGM
HGM
HGM
HGM
HGM
HGM
HGM
HGM
HGM
HGM
HGM
HGM
HGM
HGM
HGM
HGM
HGM
HGM
HGM
HGM
HGM
HGM
HGM

CAM-RP-2009-015 April 22, 2011 Revision A

Transverse Compression Properties (TC) -- (ETW)


Measured Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
2

Prepreg Lot #

Cure Cycle #

0
0

10

15

20

25

30

35

40

45

50

Transverse Compression Strength [ksi]

Transverse Compression Properties (TC) -- (ETW)


Measured Modulus

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
2

0
0.0

2.0

Transverse Compression Modulus [Msi]

Page 122 of 238

4.0

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

4.5 In-Plane Shear Properties


In-Plane Shear Properties (IPS) -- (CTD)
Strength & Modulus
HEXCEL 8552 - IM7 UNI PREPREG
Specimen
Hexcel
Hexcel Cure Prepreg
Number
Batch #
Cycle
Lot #
HFINA11FB
A
M1
1
HFINA11GB
A
M1
1
HFINA11AB
A
M1
1
HFINA1RMB
A
M1
1
HFINA21EB
A
M2
1
HFINA21FB
A
M2
1
HFINA21AB
A
M2
1
HFINB11FB
B
M1
2
HFINB11AB
B
M1
2
HFINB114B
B
M1
2
HFINB21EB
B
M2
2
HFINB21FB
B
M2
2
HFINB219B
B
M2
2
HFINB21AB
B
M2
2
HFINC11EB
C
M1
3
HFINC11FB
C
M1
3
HFINC11AB
C
M1
3
HFINC114B
C
M1
3
HFINC21EB
C
M2
3
HFINC21FB
C
M2
3
HFINC219B
C
M2
3
All specimens failed to reach 50,000 micro strain.

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
1
2
2
2
1
1
1
1
2
2
2

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

0.2% Offset
Strength [ksi]
11.066
11.048
11.460
10.779
11.063
11.154
11.065
11.277
11.275
11.194
11.564
11.661
11.067
11.578
11.549
11.420
11.565
11.211
11.233
11.564
11.395

11.29
0.24
2.10
10.78
11.66
21.00

Page 123 of 238

Modulus Avg. Specimen


[Msi]
Thickn. [in]
0.835
0.088
0.837
0.088
0.839
0.082
0.808
0.088
0.836
0.088
0.851
0.088
0.822
0.089
0.854
0.087
0.865
0.083
0.857
0.087
0.881
0.086
0.884
0.087
0.834
0.088
0.894
0.081
0.893
0.085
0.878
0.086
0.869
0.080
0.855
0.086
0.867
0.087
0.893
0.082
0.885
0.081

0.86
0.02
2.90
0.81
0.89
21.00

# Plies in
Laminate
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Avg. tply
[in]
0.0073
0.0073
0.0068
0.0074
0.0074
0.0073
0.0074
0.0072
0.0069
0.0072
0.0072
0.0072
0.0073
0.0068
0.0071
0.0072
0.0067
0.0071
0.0073
0.0068
0.0067

0.0071

0.0067
0.0074
21

CAM-RP-2009-015 April 22, 2011 Revision A

In-Plane Shear Properties (IPS) -- (CTD)


0.2% Offset Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1

Prepeg Lot #

Cure Cycle #

0
0.00

2.00

4.00

6.00

8.00

10.00

12.00

14.00

In-Plane Shear Modulus (IPS) [Msi]

In-Plane Shear Properties (IPS) -- (CTD)


Measured Modulus

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

0
0.00

0.20

0.40

0.60

0.80

In-Plane Shear Modulus (IPS) [Msi]

Page 124 of 238

1.00

1.20

Prepeg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

In-Plane Shear Properties (IPS) -- (RTD)


Strength & Modulus
HEXCEL 8552 - IM7 UNI PREPREG
Specimen
Hexcel Hexcel Cure Prepreg Cure Cycle
Number
Batch #
Cycle
Lot #
#
HFINA111A**
A
M1
1
1
HFINA112A*
A
M1
1
1
HFINA113A
A
M1
1
1
HFINA114A
A
M1
1
1
HFINA115A**
A
M1
1
1
HFINA211A**
A
M2
1
2
HFINA212A
A
M2
1
2
HFINA213A
A
M2
1
2
HFINB111A
B
M1
2
1
HFINB112A
B
M1
2
1
HFINB113A
B
M1
2
1
HFINB211A*
B
M2
2
2
HFINB212A*
B
M2
2
2
HFINB213A
B
M2
2
2
HFINC111A**
C
M1
3
1
HFINC112A
C
M1
3
1
HFINC113A**
C
M1
3
1
HFINC211A
C
M2
3
2
HFINC212A
C
M2
3
2
HFINC213A*
C
M2
3
2
HFINC214A
C
M2
3
2
*specimens failed to reach 50,000 micro strain
** data was omitted due to Biaxial Extensometer slippage
Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength at
5% Strain [ksi]

0.2% Offset
Strength [ksi]

# Plies in
Laminate

Avg. tply
[in]

12.855
12.939

7.698
7.481
7.603

0.668
0.652
0.663

0.090
0.089
0.088

12
12
12

0.0075
0.0074
0.0073

13.197

7.585
7.589
8.117
7.672
7.776
7.600
7.943
7.686

0.653
0.662
0.735
0.674
0.680
0.669
0.713
0.678

0.089
0.088
0.082
0.088
0.088
0.088
0.084
0.088

12
12
12
12
12
12
12
12

0.0074
0.0073
0.0068
0.0073
0.0073
0.0074
0.0070
0.0073

13.407

7.977

0.684

0.088

12

0.0073

13.609
13.200
13.387

7.755
7.741
8.279
7.591

0.669
0.681
0.698
0.660

0.089
0.088
0.087
0.087

12
12
12
12

0.0074
0.0073
0.0072
0.0073

13.225
0.211
1.595
12.855
13.609
12

7.756
0.218
2.808
7.481
8.279
16

0.677
0.022
3.272
0.652
0.735
16

13.228
13.121
13.259
13.092
13.405

Page 125 of 238

Modulus Avg. Specimen


[Msi]
Thickn. [in]

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

0.0073

0.0068
0.0075
16

CAM-RP-2009-015 April 22, 2011 Revision A

In-Plane Shear Properties (IPS) -- (RTD)


Measured Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

Prepeg Lot #

Cure Cycle #

0
0

10

15

20

25

In-Plane Shear Strength at 5% Strain (IPS) [ksi]

In-Plane Shear Properties (IPS) -- (RTD)


Measured Modulus

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
1
1

0
0.00

0
0.20

0.40

0.60

0.80

In-Plane Shear Modulus (IPS) [Msi]

Page 126 of 238

1.00

1.20

Prepeg Lot #

Cure Cycle #

3
2

CAM-RP-2009-015 April 22, 2011 Revision A

In-Plane Shear Properties (IPS) -- (ETW)


Strength & Modulus
HEXCEL 8552 - IM7 UNI PREPREG
Specimen
Hexcel Hexcel Cure Prepreg Cure Cycle Strength at 5%
0.2% Offset
Number
Batch #
Cycle
Lot #
#
Strain [ksi]
Strength [ksi]
HFINA11BD
A
M1
1
1
5.451
3.4082
HFINA11CD
A
M1
1
1
5.563
3.3495
HFINA11DD
A
M1
1
1
5.597
3.2809
HFINA11ED
A
M1
1
1
5.447
3.3080
HFINA21BD
A
M2
1
2
5.706
3.262
HFINA21CD
A
M2
1
2
5.657
3.373
HFINA21DD
A
M2
1
2
5.563
3.292
HFINB11BD
B
M1
2
1
5.751
3.627
HFINB11CD
B
M1
2
1
5.678
3.462
HFINB11DD*
B
M1
2
1
3.432
HFINB11ED
B
M1
2
1
5.434
3.090
HFINB21BD
B
M2
2
2
5.954
3.539
HFINB21CD
B
M2
2
2
5.657
3.350
HFINB21DD
B
M2
2
2
5.700
3.349
HFINC11BD
C
M1
3
1
5.289
3.304
HFINC11CD
C
M1
3
1
5.366
3.088
HFINC11DD
C
M1
3
1
5.178
3.050
HFINC21BD
C
M2
3
2
5.431
3.248
HFINC21CD
C
M2
3
2
5.456
3.265
HFINC21DD
C
M2
3
2
5.338
3.060
ALL SPECIMENS: SHEAR MODULUS STRAIN RANGE CUTS INTO NON-LINEAR REGION

Modulus Avg. Specimen


[Msi]
Thickn. [in]
0.308
0.081
0.317
0.089
0.304
0.089
0.313
0.088
0.311
0.089
0.315
0.088
0.313
0.088
0.321
0.082
0.311
0.087
0.315
0.087
0.303
0.086
0.336
0.083
0.305
0.088
0.307
0.087
0.308
0.082
0.283
0.087
0.286
0.086
0.282
0.089
0.283
0.088
0.299
0.087

# Plies in
Laminate
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12

Avg. tply
[in]
0.0067
0.0075
0.0075
0.0073
0.0074
0.0073
0.0073
0.0068
0.0073
0.0072
0.0072
0.0069
0.0073
0.0073
0.0069
0.0073
0.0072
0.0074
0.0073
0.0072

* Unable to reach 50,000 microstrain


Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

5.54
0.19
3.38
5.18
5.95
19.00

3.31
0.15
4.63
3.05
3.63
20.00

Page 127 of 238

0.31
0.01
4.51
0.28
0.34
20.00

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

0.0072

0.0067
0.0075
20

CAM-RP-2009-015 April 22, 2011 Revision A

In-Plane Shear Properties (IPS) -- (ETW)


Measured Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

Prepeg Lot #

Cure Cycle #

0
0

10

15

20

25

In-Plane Shear Strength at 5% Strain (IPS) [ksi]

In-Plane Shear Properties (IPS) -- (ETW)


Measured Modulus

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
1
1

0
0.00

0.20

0.40

0.60

0.80

In-Plane Shear Modulus (IPS) [Msi]

Page 128 of 238

1.00

1.20

Prepeg Lot #

Cure Cycle #

3
2

CAM-RP-2009-015 April 22, 2011 Revision A

4.6 Unnotched Compression 0 Properties


Laminate Unnotched Compression Properties (UNC0) -- (CTD)
Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen Hexcel Hexcel Cure Prepreg
Cure Cycle
Strength Modulus Poisson's
Number
Batch #
Cycle
Lot #
Batch #
[ksi]
[Msi]
Ratio
HFIRB115B
B
M1
2
1
110.782
7.426
0.060
HFIRB116B
B
M1
2
1
104.576
7.503
0.038
HFIRB117B
B
M1
2
1
114.578
7.466
0.030
HFIRB215B
B
M2
2
2
111.952
7.849
0.045
HFIRB216B
B
M2
2
2
108.713
7.436
0.033
HFIRB217B
B
M2
2
2
115.841
7.723
0.041
HFIRC115B
C
M1
3
1
112.448
7.704
0.047
HFIRC116B
C
M1
3
1
118.903
7.839
0.033
HFIRC117B
C
M1
3
1
106.963
7.809
0.044
Batch A Cure Cycle 1 and 2 and Batch C Cure Cycle 2 has improper layup so data was removed

Average 111.640
Standard Dev. 4.484
Coeff. of Var. [%] 4.017
Min. 104.576
Max. 118.903
Number of Spec.
9

7.639
0.180
2.357
7.426
7.849
9

Avg. Specimen
Thickn. [in]
0.109
0.109
0.108
0.109
0.109
0.109
0.112
0.111
0.111

# Plies in
Laminate
15
15
15
15
15
15
15
15
15

0.041
0.009
22.360
0.030
0.060
9

Failure
Mode
BGM
BGM
BGM
BGM
BGM
BGM/BAB
BGM
HAT
BAT

Average norm
Standard Dev. norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Avg. tply
[in]
0.0073
0.0073
0.0072
0.0073
0.0073
0.0072
0.0075
0.0074
0.0074

Strengthnorm
[ksi]
111.944
105.464
114.578
112.799
109.954
116.431
116.578
121.747
109.819

Modulusnorm
[Msi]
7.504
7.567
7.466
7.908
7.521
7.762
7.987
8.027
8.017

0.0073

113.257
4.748
4.192
105.464
121.747
9

7.751
0.239
3.083
7.466
8.027
9

0.0072
0.0075

Laminate Unnotched Compression Properties (UNC0) -- (CTD)

Cure Cycle #
Prepreg Lot #

2
1

0
0

25

50

75

100

125

Prepreg Lot #

Cure Cycle #

3
2

150

Laminate Compression Strength (UNC0) [ksi]

Laminate Unnotched Compression Properties (UNC0) -- (CTD)


Normalized Modulus

Cure Cycle #
Prepreg Lot #

HEXCEL 8552 - IM7 UNI PREPREG


3

2
2

0
0.0

2.0

4.0

6.0

8.0

10.0

Laminate Compression Modulus (UNC0) [Msi]

Page 129 of 238

12.0

14.0

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Unnotched Compression Properties (UNC0) -- (RTD)


Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Hexcel Hexcel Cure Prepreg
Cure Cycle
Strength Modulus Poisson's
Number
Batch #
Cycle
Lot #
Batch #
[ksi]
[Msi]
Ratio
HFIRB111A
B
M1
2
1
91.558
7.732
0.035
HFIRB112A
B
M1
2
1
97.669
7.541
0.037
HFIRB113A
B
M1
2
1
98.542
7.419
0.035
HFIRB211A
B
M2
2
2
96.791
7.564
0.036
HFIRB212A
B
M2
2
2
93.387
7.550
0.037
HFIRB213A
B
M2
2
2
94.371
7.559
0.034
HFIRC111A
C
M1
3
1
89.785
7.451
0.032
HFIRC112A
C
M1
3
1
98.082
7.544
0.033
HFIRC113A
C
M1
3
1
95.814
7.319
0.039
Batch A Cure Cycle 1 and 2 and Batch C Cure Cycle 2 has improper layup so data was removed

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

95.111
3.061
3.218
89.785
98.542
9

7.520
0.115
1.530
7.319
7.732
9

Avg. Specimen
Thickn. [in]
0.101
0.107
0.109
0.108
0.108
0.108
0.102
0.109
0.112

# Plies in
Laminate
15
15
15
15
15
15
15
15
15

0.035
0.002
6.397
0.032
0.039
9

Failure
Mode
BGM
BGM
BGM
BAT
BGM
BGM
BGM
BAT
BGM

Avg. tply
[in]
0.0068
0.0071
0.0073
0.0072
0.0072
0.0072
0.0068
0.0072
0.0075

Strengthnorm
[ksi]
85.878
96.449
99.743
97.015
93.603
94.794
84.825
98.747
99.525

Modulusnorm
[Msi]
7.253
7.447
7.509
7.582
7.567
7.592
7.039
7.595
7.602

0.0071

94.509
5.587
5.912
84.825
99.743
9

7.465
0.195
2.615
7.039
7.602
9

Average norm
Standard Dev.norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

0.0068
0.0075

Laminate Unnotched Compression Properties (UNC0) -- (RTD)


Normalized Strength
3
3

Prepreg Lot #

Cure Cycle #

Cure Cycle #
Prepreg Lot #

2
2
1

0
0

25

50

75

100

125

150

Laminate Compression Strength (UNC0) [ksi]

Laminate Unnotched Compression Properties (UNC0) -- (RTD)


Normalized Modulus
3
3
2
2

0
0.0

2.0

4.0

6.0

8.0

10.0

Laminate Compression Modulus (UNC0) [Msi]

Page 130 of 238

12.0

14.0

Prepreg Lot #

Cure Cycle #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A


Laminate Unnotched Compression Properties (UNC0) -- (ETD)
Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen Hexcel Hexcel Cure Prepreg
Cure Cycle
Strength
Modulus
Poisson's
Number
Batch #
Cycle
Lot #
Batch #
[ksi]
[Msi]
Ratio
HFIRB11CC
B
M1
2
1
75.164
7.462
0.032
HFIRB11DC
B
M1
2
1
66.566
7.458
0.031
HFIRB118C
B
M1
2
1
77.437
7.109
0.032
HFIRB219C
B
M2
2
2
78.236
7.400
0.025
HFIRB21DC
B
M2
2
2
81.637
7.834
0.025
HFIRB218C
B
M2
2
2
68.787
7.838
0.031
HFIRC11DC
C
M1
3
1
71.555
7.594
0.034
HFIRC1RMC
C
M1
3
1
79.904
7.697
0.033
HFIRC1RNC
C
M1
3
1
76.899
7.390
0.022
Batch A Cure Cycle 1 and 2 and Batch C Cure Cycle 2 has improper layup so data was removed
Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

75.132
5.118
6.813
66.566
81.637
9

7.531
0.235
3.123
7.109
7.838
9

Avg. Specimen
Thickn. [in]
0.108
0.108
0.108
0.110
0.101
0.109
0.111
0.110
0.113

0.030
0.004
14.554
0.022
0.034
9

# Plies in
Laminate
15
15
15
15
15
15
15
15
15

Failure
Mode
BAB
HGM
HAB
BAB
BAT
BGM
BGM
BGM
BGM

Average norm
Standard Dev. norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Avg. tply
[in]
0.0072
0.0072
0.0072
0.0073
0.0067
0.0072
0.0074
0.0073
0.0075

Strengthnorm
[ksi]
75.059
66.781
77.401
79.697
76.509
69.127
73.587
81.341
80.246

Modulusnorm
[Msi]
7.452
7.483
7.105
7.538
7.342
7.876
7.810
7.835
7.712

0.0072

75.528
4.992
6.610
66.781
81.341
9

7.573
0.258
3.407
7.105
7.876
9

0.0067
0.0075
9

Laminate Unnotched Compression Properties (UNC0) -- (ETD)


Normalized Strength
3
3

Cure Cycle #

2
2
1

Prepreg Lot #

Cure Cycle #
Prepreg Lot #

0
0

25

50

75

100

125

Laminate Compression Strength (UNC0) [ksi]

Laminate Unnotched Compression Properties (UNC0) -- (ETD)


Normalized Modulus
HEXCEL 8552 - IM7 UNI PREPREG
3
Cure Cycle #

2
2

0
0.0

2.0

4.0

6.0

8.0

10.0

Laminate Compression Modulus (UNC0) [Msi]

Page 131 of 238

12.0

14.0

Prepreg Lot #

Cure Cycle #

Prepreg Lot #

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Unnotched Compression Properties (UNC0) -- (ETW)


Strength & Modulus
HEXCEL 8552 - IM7 UNI PREPREG

normalizing tply
[in]
0.0072

Specimen
Hexcel Hexcel Cure Prepreg Cure Cycle Strength Modulus* Poisson's Avg. Specimen # Plies in Failure
Avg. tply Strengthnorm Modulusnorm
Number
Batch #
Cycle
Lot #
#
[ksi]
[Msi]
Ratio
Thickn. [in]
Laminate
Mode
[in]
[ksi]
[Msi]
HFIRB11ED
B
M1
2
1
64.567
0.110
15
BGM
0.0073
65.543
HFIRB11FD
B
M1
2
1
61.927
0.110
15
BGM
0.0073
62.978
HFIRB11GD
B
M1
2
1
64.966
0.107
15
BGM
0.0072
64.645
HFIRB11HD
B
M1
2
1
74.964
0.102
15
BGM
0.0068
70.950
HFIRB21ED
B
M2
2
2
52.845
0.110
15
HAT
0.0073
53.938
HFIRB21FD
B
M2
2
2
57.458
0.109
15
BGM
0.0073
58.229
HFIRB21GD
B
M2
2
2
62.622
0.108
15
BGM
0.0072
62.786
HFIRC11ED
C
M1
3
1
52.059
0.113
15
BAT
0.0075
54.357
HFIRC11FD
C
M1
3
1
60.193
0.113
15
BGM
0.0075
63.045
HFIRC11GD
C
M1
3
1
59.456
0.110
15
BGM
0.0073
60.649
HFIRB11ID*
B
M1
2
1
0.099
15
BAT
HFIRB114D
B
M1
2
1
69.360
7.748
0.019
0.110
15
BAB
0.0073
70.795
7.908
HFIRB1RMD
B
M1
2
1
69.098
7.898
0.020
0.107
15
BAT
0.0071
68.245
7.801
HFIRB21HD
B
M2
2
2
7.963
0.015
0.103
15
HIT
0.0069
7.614
HFIRB21ID
B
M2
2
2
70.790
8.216
0.019
0.103
15
HAB
0.0068
67.185
7.797
HFIRB214D
B
M2
2
2
67.719
8.128
0.013
0.108
15
BGM
0.0072
67.635
8.118
HFIRC11HD
C
M1
3
1
65.131
7.745
0.011
0.103
15
BAB
0.0069
62.327
7.412
HFIRC114D
C
M1
3
1
67.033
7.531
0.021
0.112
15
BAT
0.0075
69.588
7.818
HFIRC118D
C
M1
3
1
68.351
7.298
0.021
0.110
15
BAB
0.0074
69.827
7.456
Compressive strength for HFIRA21ID and HFIRB21HD is not reported as unacceptable failure mode was
Modulus not reported due to improper strain gage adhesive used
Batch A Cure Cycle 1 and 2 and Batch C Cure Cycle 2 has improper layup so data was removed
COMPRESSIVE STRENGTH WAS NOT REPORTED FOR SPECIMEN # HFIRC21FD DUE TO UNACCEPTABLE FAILURE MODE.
* Specimens have uneven grip marks so data is not reported
64.278
7.740
Average 64.032
7.816
0.017
Average norm 0.0072
5.289
0.236
Standard Dev. 6.208
0.303
0.004
Standard Dev.norm
Coeff. of Var. [%] 9.696
3.882
22.032
Coeff. of Var. [%]norm
8.228
3.043
Min. 52.059
7.298
0.011
Min.
0.0068
53.938
7.412
Max. 74.964
8.216
0.021
Max.
0.0075
70.950
8.118
Number of Spec.
17
8
8
Number of Spec.
17
8

Page 132 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Unnotched Compression Properties (UNC0) -- (ETW)


Normalized Strength
HEXCEL 8552 - IM7 UNI PREPREG
3
Cure Cycle #

Prepreg Lot #

Cure Cycle #

0
0

25

50

75

100

125

150

Laminate Compression Strength (UNC0) [ksi]

Laminate Unnotched Compression Properties (UNC0) -- (ETW)


Normalized Modulus
HEXCEL 8552 - IM7 UNI PREPREG
3
3

2
2
1

0
0.0

2.0

4.0

6.0

8.0

Laminate Compression Modulus (UNC0) [Msi]

Page 133 of 238

10.0

12.0

Prepreg Lot #

Cure Cycle #

Cure Cycle #
Prepreg Lot #

Prepreg Lot #

CAM-RP-2009-015 April 22, 2011 Revision A

4.7 Unnotched Tension 0 Properties


Laminate Unnotched Tension Properties (UNT0) -- (CTD)
Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFIPA116B
HFIPA117B
HFIPA118B
HFIPA119B
HFIPA216B
HFIPA217B
HFIPA218B
HFIPB116B
HFIPB117B
HFIPB118B
HFIPB216B
HFIPB217B
HFIPB218B
HFIPC116B
HFIPC117B
HFIPC118B
HFIPC216B
HFIPC217B
HFIPC218B

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

Strength
[ksi]
140.452
138.380
149.109
138.826
153.285
148.863
153.556
149.540
154.720
146.994
150.463
152.509
150.815
154.979
156.681
148.810
151.797
152.579
155.700

Modulus
[Msi]
11.491
11.251
11.735
11.390
11.488
11.543
11.680
11.876
11.886
11.837
11.832
11.686
11.835
11.838
11.909
11.670
11.830
11.818
11.820

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

149.898
5.417
3.614
138.380
156.681
19

11.706
0.189
1.612
11.251
11.909
19

Avg. Specimen
Thickn. [in]
0.059
0.059
0.059
0.060
0.060
0.060
0.059
0.058
0.057
0.058
0.058
0.058
0.058
0.058
0.059
0.060
0.058
0.058
0.059

Page 134 of 238

# Plies in
Laminate
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8

Failure
Mode
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LWB
LWB
LGM
LAB
LGM
LGM
LGM
LGM
LGM
LGM

Average norm
Standard Dev.norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Avg. tply
[in]
0.0073
0.0074
0.0073
0.0076
0.0075
0.0075
0.0074
0.0072
0.0071
0.0072
0.0072
0.0072
0.0073
0.0073
0.0073
0.0075
0.0073
0.0072
0.0074

Strengthnorm
[ksi]
142.931
142.064
151.439
145.615
158.607
154.204
157.333
149.929
153.556
147.675
150.767
153.523
153.040
157.176
159.854
154.579
153.554
153.462
159.664

Modulusnorm
[Msi]
11.694
11.551
11.919
11.947
11.887
11.958
11.968
11.907
11.797
11.892
11.856
11.763
12.010
12.006
12.151
12.122
11.967
11.886
12.121

0.0073

152.578
5.172
3.389
142.064
159.854
19

11.916
0.147
1.236
11.551
12.151
19

0.0071
0.0076

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Unnotched Tension Properties (UNT0) -- (CTD)


Normalized Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

Cure Cycle #

Prepreg Lot #

3
2
2
1
1

0
0

20

40

60

80

100

120

140

160

180

200

LaminateTension Strength (UNT1) [ksi]

Laminate Unnotched Tension Properties (UNT0) -- (CTD)


Normalized Modulus

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

Cure Cycle #

2
1
1

0
0.0

2.0

4.0

6.0

8.0

Laminate Tension Modulus (UNT1) [Msi]

Page 135 of 238

10.0

12.0

14.0

Prepreg Lot #

3
2

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Unnotched Tension Properties (UNT0) -- (RTD)


Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen Hexcel Hexcel Cure
Prepreg
Cure Cycle
Number
Batch #
Cycle
Lot #
#
HFIPA111A*
A
M1
1
1
HFIPA112A
A
M1
1
1
HFIPA113A
A
M1
1
1
HFIPA114A
A
M1
1
1
HFIPA211A
A
M2
1
2
HFIPA212A
A
M2
1
2
HFIPA213A
A
M2
1
2
HFIPB111A
B
M1
2
1
HFIPB112A
B
M1
2
1
HFIPB113A
B
M1
2
1
HFIPB211A
B
M2
2
2
HFIPB212A
B
M2
2
2
HFIPB213A
B
M2
2
2
HFIPC111A
C
M1
3
1
HFIPC112A
C
M1
3
1
HFIPC113A
C
M1
3
1
HFIPC211A
C
M2
3
2
HFIPC212A
C
M2
3
2
HFIPC213A
C
M2
3
2
*Data from was removed due to thickness taper due to pinching
Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength
[ksi]

Modulus
[Msi]

Avg. Specimen
Thickn. [in]

# Plies in
Laminate

Failure
Mode

Avg. tply
[in]

Strengthnorm
[ksi]

Modulusnorm
[Msi]

8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8

LWT/LWB
LGM
LWT/LAB
LAT/LAB
LGM
LWB/LWT
LGM
LWT/LAB
LWT/LWB
LGM
LGM
LWB
LWT
LWT
LGM
LGM
LGM
LGM

0.0074
0.0075
0.0073
0.0071
0.0076
0.0074
0.0068
0.0073
0.0072
0.0074
0.0073
0.0072
0.0074
0.0075
0.0072
0.0069
0.0074
0.0073

165.214
172.621
171.491
168.451
177.065
181.648
157.619
166.842
168.570
170.014
173.149
178.704
174.295
175.247
182.904
143.990
178.570
178.533

11.706
12.222
12.097
11.504
12.036
12.027
11.618
11.875
11.943
12.188
11.973
12.052
12.027
12.104
12.084
11.926
12.134
12.342

0.0073

171.385
9.304
5.429
143.990
182.904
18

11.992
0.211
1.757
11.504
12.342
18

160.028
11.338
0.059
165.993
11.753
0.060
170.162
12.003
0.058
170.274
11.629
0.057
166.740
11.334
0.061
177.388
11.745
0.059
167.506
12.347
0.054
164.698
11.723
0.058
169.650
12.020
0.057
165.886
11.892
0.059
169.856
11.745
0.059
177.983
12.004
0.058
168.776
11.646
0.059
169.224
11.688
0.060
182.062
12.029
0.058
150.387
12.455
0.055
173.159
11.766
0.059
175.088
12.104
0.059
on edge of panel during bagging.
169.159
7.077
4.183
150.387
182.062
18

11.846
0.296
2.496
11.334
12.455
18

Average norm
Standard Dev.norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

0.0068
0.0076

Laminate Unnotched Tension Properties (UNT0) -- (RTD)


Normalized Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

Cure Cycle #

2
1

Prepreg Lot #

3
2

0
0

20

40

60

80

100

120

140

160

180

200

Laminate Tension Strength (UNT0) [ksi]

Laminate Unnotched Tension Properties (UNT0) -- (RTD)


Normalized Modulus

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

0
0.0

2.0

4.0

6.0

8.0

Laminate Tension Modulus (UNT0) [Msi]

.
Page 136 of 238

10.0

12.0

14.0

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Unnotched Tension Properties (UNT0) -- (ETW)


Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Hexcel
Hexcel Cure
Prepreg Cure Cycle Strength Modulus
Avg. Specimen
Number
Batch #
Cycle
Lot #
#
[ksi]
[Msi]
Thickn. [in]
HFIPA11BD
A
M1
1
1
176.795
11.690
0.060
HFIPA11CD
A
M1
1
1
174.123
11.286
0.060
HFIPA11DD
A
M1
1
1
175.012
11.816
0.059
HFIPA11ED
A
M1
1
1
170.114
11.463
0.059
HFIPA21BD*
A
M2
1
2
HFIPA21CD
A
M2
1
2
169.361
11.335
0.061
HFIPA21DD
A
M2
1
2
170.950
11.590
0.059
HFIPB11BD
B
M1
2
1
178.511
12.198
0.058
HFIPB11CD
B
M1
2
1
164.549
11.798
0.058
HFIPB11ED
B
M1
2
1
172.023
11.659
0.058
HFIPB21BD
B
M2
2
2
186.089
11.843
0.058
HFIPB21CD
B
M2
2
2
169.321
11.605
0.058
HFIPB21DD
B
M2
2
2
175.679
11.641
0.058
HFIPC11BD
C
M1
3
1
172.929
11.832
0.057
HFIPC11CD
C
M1
3
1
177.552
11.718
0.059
HFIPC11DD*
C
M1
3
1
11.947
0.058
HFIPC11ED
C
M1
3
1
179.743
11.724
0.059
HFIPC21BD
C
M2
3
2
189.339
12.258
0.055
HFIPC21CD
C
M2
3
2
181.866
11.677
0.060
HFIPC21DD
C
M2
3
2
183.749
11.894
0.059
*Data from was removed due to thickness variation due to pinching on edge of panel during bagging.
Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

175.984
6.450
3.665
164.549
189.339
18

# Plies in
Laminate
8
8
8
8

Failure
Mode
LAT / LGM / LAB
LAT / LAB
LWT / LGM
LAT / LAB

Avg. tply
[in]
0.0076
0.0075
0.0073
0.0074

Strengthnorm
[ksi]
185.594
180.471
177.848
174.889

Modulusnorm
[Msi]
12.272
11.697
12.008
11.785

8
8
8
8
8
8
8
8
8
8
8
8
8
8
8

LAT / LWB
LAT / LAB
LAT / LWB
LAT / LGM
LAT / LGM
LAT / LGM / LAB
LGM
LAT / LGM
LGM / LWB
LAT / LWB
LIT / LWB
LAT / LAB
LAT / LAB
LWT / LGM / LAB
LAT / LAB

0.0076
0.0074
0.0073
0.0073
0.0072
0.0073
0.0072
0.0073
0.0072
0.0074
0.0073
0.0074
0.0069
0.0075
0.0074

178.427
175.007
180.784
165.977
172.720
188.028
169.272
177.254
172.579
183.203
184.528
181.560
189.181
188.853

11.942
11.865
12.353
11.900
11.706
11.966
11.601
11.745
11.808
12.091
12.034
12.036
11.755
12.147
12.224

Average norm
Standard Dev. norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

0.0073

179.232
6.718
3.748
165.977
189.181
18

11.944
0.211
1.764
11.601
12.353
19

11.735
0.245
2.091
11.286
12.258
19

Page 137 of 238

0.0069
0.0076

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Unnotched Tension Properties (UNT0) -- (ETW)


Normalized Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
2

1
1

Prepreg Lot #

Cure Cycle #

0
0

20

40

60

80

100

120

140

160

180

200

LaminateTension Strength (UNT0) [ksi]

Laminate Unnotched Tension Properties (UNT0) -- (ETW)


Normalized Modulus

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
2

0
0.0

2.0

4.0

6.0

8.0

Laminate Tension Modulus (UNT0) [Msi]

Page 138 of 238

10.0

12.0

14.0

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

4.8 Unnotched Tension 1 Properties


Laminate Unnotched Tension Properties (UNT1) -- (CTD)
Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFIAA116B
HFIAA117B
HFIAA118B
HFIAA119B
HFIAA215B
HFIAA216B
HFIAA217B
HFIAB115B
HFIAB116B
HFIAB117B
HFIAC115B
HFIAC116B
HFIAC111B
HFIAC215B
HFIAC216B
HFIAC217B

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
1
1
1
2
2
2

Strength
[ksi]
98.622
99.922
102.825
95.738
98.424
97.607
93.700
97.175
97.723
101.304
96.981
104.197
99.363
95.780
100.348
100.956

Modulus
[Msi]
8.511
8.181
8.274
8.311
8.242
8.342
8.231
8.253
8.290
8.519
8.237
8.331
7.913
8.362
8.450
8.414

98.792
2.750
2.784
93.700
104.197
16

8.304
0.145
1.742
7.913
8.519
16

Avg. Specimen
Thickn. [in]
0.118
0.116
0.116
0.118
0.116
0.116
0.116
0.116
0.116
0.115
0.118
0.117
0.106
0.117
0.115
0.117

# Plies in
Laminate
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16

Failure
Mode
LGM / AGM
AGM
AWT
AGM
LGM
LGM
LWB
AGM
AWT
AGM
AGM / DGM
AGM
AGM
AGM
AWT
AWB

Avg. tply
[in]
0.0074
0.0073
0.0073
0.0074
0.0073
0.0073
0.0072
0.007
0.0073
0.0072
0.0073
0.0073
0.0066
0.0073
0.0072
0.0073

Strengthnorm
[ksi]
101.333
100.789
103.584
98.009
99.449
98.313
94.093
97.639
98.514
101.245
98.974
105.840
91.601
97.485
100.290
102.402

Modulusnorm
[Msi]
8.745
8.252
8.335
8.508
8.328
8.402
8.265
8.293
8.357
8.514
8.406
8.462
7.295
8.511
8.446
8.535

0.0072

99.348
3.442
3.464
91.601
105.840
16

8.353
0.309
3.696
7.295
8.745
16

Data for HFIAB 21XB w as rem oved due to unbalanced lay up.

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Page 139 of 238

Average norm
Standard Dev. norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

0.0066
0.0074
16

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Unnotched Tension Properties (UNT1) -- (CTD)


Normalized Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

Prepreg Lot #

Cure Cycle #

0
0

20

40

60

80

100

120

140

160

180

200

LaminateTension Strength (UNT1) [ksi]

Laminate Unnotched Tension Properties (UNT1) -- (CTD)


Normalized Modulus

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

0
0.0

2.0

4.0

6.0

8.0

10.0

12.0

14.0

16.0

Laminate Tension Modulus (UNT1) [Msi]

Page 140 of 238

18.0

20.0

22.0

24.0

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A


Laminate Unnotched Tension Properties (UNT1) -- (RTD)
Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFIAA111A
HFIAA112A
HFIAA113A
HFIAA114A
HFIAA212A
HFIAA213A
HFIAA214A
HFIAB111A
HFIAB112A
HFIAB113A
HFIAC112A
HFIAC113A
HFIAC114A
HFIAC211A
HFIAC212A
HFIAC213A

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
1
1
1
2
2
2

Strength
[ksi]
102.024
101.477
103.733
103.511
105.753
104.779
101.098
96.381
107.280
106.160
110.004
102.238
111.125
97.791
108.416
102.436

Modulus
[Msi]
8.116
8.093
8.310
8.543
8.366
8.528
8.393
8.227
8.554
8.257
8.691
8.186
8.519
7.900
8.618
8.133

104.013
4.054
3.898
96.381
111.125
16

8.340
0.224
2.682
7.900
8.691
16

Avg. Specimen
Thickn. [in]
0.117
0.108
0.119
0.118
0.118
0.118
0.116
0.107
0.117
0.117
0.119
0.120
0.117
0.106
0.118
0.119

# Plies in
Laminate
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16

Failure
Mode
AWT
AGM
AGM
AWB
AWT
AGM
AGM
AGM
AGM
AWT
AWB
AWT
AWB
AWB
AGM
AGM

Avg. tply
[in]
0.0073
0.0068
0.0074
0.0074
0.0074
0.0073
0.0072
0.0067
0.0073
0.0073
0.0074
0.0075
0.0073
0.0066
0.0074
0.0075

Strengthnorm
[ksi]
103.515
95.194
106.855
105.892
107.956
106.871
101.493
89.563
109.174
108.049
113.712
106.246
113.070
90.080
111.066
106.230

Modulusnorm
[Msi]
8.235
7.592
8.560
8.739
8.541
8.698
8.426
7.645
8.705
8.404
8.984
8.507
8.668
7.277
8.828
8.435

0.0072

104.685
7.276
6.950
89.563
113.712
16

8.390
0.480
5.727
7.277
8.984
16

Data for HFIAB 21XA w as rem oved due to unbalanced lay up.

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Page 141 of 238

Average norm
Standard Dev. norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

0.0066
0.0075
16

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Unnotched Tension Properties (UNT1) -- (RTD)


Normalized Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

Cure Cycle #

2
1
1

Prepreg Lot #

3
2

0
0

50

100

150

200

250

Laminate Tension Strength (UNT1) [ksi]

Laminate Unnotched Tension Properties (UNT1) -- (RTD)


Normalized Modulus

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

0
0.0

2.0

4.0

6.0

8.0

10.0

12.0

14.0

16.0

Laminate Tension Modulus (UNT1) [Msi]

Page 142 of 238

18.0

20.0

22.0

24.0

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A


Laminate Unnotched Tension Properties (UNT1) -- (ETW)
Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Hexcel
Hexcel Cure
Prepreg
Cure Cycle
Strength
Number
Batch #
Cycle
Lot #
#
[ksi]
HFIAA11AD**
A
M1
1
1
HFIAA11BD
A
M1
1
1
109.007
HFIAA11CD
A
M1
1
1
111.481
HFIAA11DD
A
M1
1
1
107.732
HFIAA11FD
A
M1
1
1
104.093
HFIAA218D
A
M2
1
2
112.321
HFIAA219D
A
M2
1
2
109.153
HFIAA21AD
A
M2
1
2
108.151
HFIAB118D
B
M1
2
1
111.994
HFIAB119D
B
M1
2
1
115.193
HFIAB11AD
B
M1
2
1
106.398
HFIAC118D
C
M1
3
1
111.908
HFIAC119D
C
M1
3
1
119.118
HFIAC11AD
C
M1
3
1
112.566
HFIAC218D
C
M2
3
2
115.435
HFIAC219D
C
M2
3
2
114.366
HFIAC21AD
C
M2
3
2
115.103
**SPECIMEN SLIPPED DURING TESTING, STRENGTH NOT REPORTED

Modulus
[Msi]
7.968
7.825
7.933
8.074
7.898
7.906
7.460
7.522
8.292
8.207
7.155
8.128
8.105
7.754
7.926
8.241
8.187

Avg. Specimen
Thickn. [in]
0.117
0.108
0.118
0.118
0.116
0.118
0.118
0.108
0.117
0.117
0.118
0.119
0.115
0.119
0.118
0.119
0.113

# Plies in
Laminate
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16

Failure
Mode
*
AGM/AWB
AGM
AGM
AGM
DGM
DGM
DGM/AWT/AWB
DGM/AGM
DGM
DGM/AWB
DGM
DGM
DGM
DGM
DGM
LWT/DGM

Avg. tply
[in]
0.0073
0.0067
0.0073
0.0073
0.0073
0.0073
0.0074
0.0068
0.0073
0.0073
0.0074
0.0075
0.0072
0.0075
0.0074
0.0074
0.0071

Strengthnorm
[ksi]
102.115
113.739
109.929
104.861
114.612
111.521
101.642
113.420
117.443
109.292
115.875
119.290
116.491
118.224
118.155
112.772

Modulusnorm
[Msi]
8.098
7.330
8.094
8.238
7.956
8.067
7.622
7.069
8.398
8.367
7.350
8.416
8.117
8.024
8.117
8.514
8.021

0.0073

112.461
5.606
4.985
101.642
119.290
16

7.988
0.412
5.162
7.069
8.514
17

Data for HFIAB 21XD w as rem oved due to unbalanced lay up.

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

111.501
3.904
3.501
104.093
119.118
16

7.916
0.305
3.857
7.155
8.292
17

Page 143 of 238

Average norm
Standard Dev. norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

0.0067
0.0075
17

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Unnotched Tension Properties (UNT1) -- (ETW)


Normalized Strength
Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

Cure Cycle #

2
1

Prepreg Lot #

3
2

0
0

50

100

150

200

250

LaminateTension Strength (UNT1) [ksi]

Laminate Unnotched Tension Properties (UNT1) -- (ETW)


Normalized Modulus

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

0
0.0

2.0

4.0

6.0

8.0

10.0

12.0

14.0

16.0

Laminate Tension Modulus (UNT1) [Msi]

Page 144 of 238

18.0

20.0

22.0

24.0

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

4.9 Unnotched Tension 2 Properties


Laminate Unnotched Tension Properties (UNT2) -- (CTD)
Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen Hexcel Hexcel Cure Prepreg Cure Cycle Strength Modulus Avg. Specimen # Plies in Failure
Number
Batch #
Cycle
Lot #
#
[ksi]
[Msi]
Thickn. [in]
Laminate Mode
HFIBA117B
A
M1
1
1
68.999
5.320
0.147
20
AGM
HFIBA118B
A
M1
1
1
67.700
5.143
0.149
20
AGM
HFIBA119B
A
M1
1
1
68.762
5.300
0.148
20
AGM
HFIBA11AB*
A
M1
1
1
HFIBA216B
A
M2
1
2
65.977
5.366
0.145
20
AWB
HFIBA217B
A
M2
1
2
69.702
5.413
0.145
20
AWB
HFIBA218B
A
M2
1
2
68.153
5.384
0.148
20
AGM
HFIBB1X3B
B
M1
2
1
69.069
5.565
0.143
20
AGM
HFIBB1X4B
B
M1
2
1
69.980
5.623
0.141
20
AWB
HFIBB217B
B
M2
2
2
70.872
5.548
0.147
20
AGM
HFIBB218B
B
M2
2
2
66.597
5.412
0.149
20
AWT
HFIBB219B
B
M2
2
2
72.926
5.588
0.149
20
AWT
HFIBC116B
C
M1
3
1
68.989
5.402
0.146
20
AWB
HFIBC117B
C
M1
3
1
69.926
5.385
0.146
20
AWB
HFIBC118B
C
M1
3
1
69.297
5.315
0.148
20
AGM
HFIBC216B
C
M2
3
2
68.195
5.431
0.148
20
AWB
HFIBC217B
C
M2
3
2
69.646
5.518
0.146
20
AGM
HFIBC218B
C
M2
3
2
67.780
5.499
0.148
20
AGM
*Data was removed due to thickness taper due to pinching on edge of panel during bagging.
Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

68.975
1.605
2.328
65.977
72.926
17

5.424
0.123
2.263
5.143
5.623
17

Page 145 of 238

Avg. tply
[in]
0.0073
0.0074
0.0074

Strengthnorm Modulusnorm
[ksi]
[Msi]
70.196
5.412
69.902
5.310
70.433
5.429

0.0073
0.0073
0.0074
0.0072
0.0071
0.0073
0.0075
0.0074
0.0073
0.0073
0.0074
0.0074
0.0073
0.0074

66.603
70.340
69.927
68.637
68.733
72.102
68.933
75.289
70.139
70.914
71.118
69.884
70.790
69.796

5.417
5.463
5.524
5.530
5.523
5.645
5.602
5.769
5.492
5.461
5.454
5.565
5.608
5.662

Average norm 0.0073


Standard Dev.norm
Coeff. of Var. [%]norm
Min.
0.0071
Max.
0.0075
Number of Spec.

70.220
1.783
2.539
66.603
75.289
17

5.522
0.112
2.030
5.310
5.769
17

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Unnotched Tension Properties (UNT2) -- (CTD)


Normalized Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1

Prepreg Lot #

Cure Cycle #

0
0

20

40

60

80

100

LaminateTension Strength (UNT2) [ksi]

120

Laminate Unnotched Tension Properties (UNT2) -- (CTD)


Normalized Modulus

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

0
0.0

1.0

2.0

3.0

4.0

5.0

Laminate Tension Modulus (UNT2) [Msi]

Page 146 of 238

6.0

7.0

8.0

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Unnotched Tension Properties (UNT2) -- (RTD)


Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen Hexcel Hexcel Cure Prepreg Cure Cycle Strength Modulus Avg. Specimen # Plies in
Number
Batch #
Cycle
Lot #
#
[ksi]
[Msi]
Thickn. [in] Laminate
HFIBA111A
A
M1
1
1
65.315
5.006
0.139
20
HFIBA113A
A
M1
1
1
66.335
5.060
0.148
20
HFIBA114A
A
M1
1
1
66.255
5.156
0.146
20
HFIBA115A
A
M1
1
1
65.636
4.951
0.147
20
HFIBA211A
A
M2
1
2
67.895
5.150
0.138
20
HFIBA212A
A
M2
1
2
69.978
5.196
0.147
20
HFIBA213A
A
M2
1
2
66.443
5.106
0.146
20
HFIBB1X1A
B
M1
2
1
67.953
5.536
0.135
20
HFIBB1X2A
B
M1
2
1
63.968
5.241
0.145
20
HFIBB211A
B
M2
2
2
62.419
5.092
0.133
20
HFIBB212A
B
M2
2
2
69.711
5.539
0.149
20
HFIBB213A
B
M2
2
2
66.311
5.243
0.149
20
HFIBC111A
C
M1
3
1
66.102
5.146
0.136
20
HFIBC112A
C
M1
3
1
69.586
5.316
0.148
20
HFIBC113A
C
M1
3
1
69.367
5.146
0.148
20
HFIBC211A
C
M2
3
2
69.692
5.394
0.140
20
HFIBC212A
C
M2
3
2
66.268
5.421
0.149
20
HFIBC213A
C
M2
3
2
68.155
5.398
0.147
20

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

67.077
2.124
3.167
62.419
69.978
18

5.228
0.173
3.305
4.951
5.539
18

Page 147 of 238

Failure
Mode
DGM
DGM
DGM
DGM
DWT
DGM
DWB
DGM
DGM
DGM
DGM
DGM
DGM
DGM
DGM
DWB/DGM
DGM
DGM

Average norm
Standard Dev. norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Avg. tply
[in]
0.0070
0.0074
0.0073
0.0073
0.0069
0.0073
0.0073
0.0067
0.0072
0.0066
0.0074
0.0075
0.0068
0.0074
0.0074
0.0070
0.0074
0.0074

0.0072

0.0066
0.0075

Strengthnorm Modulusnorm
[ksi]
[Msi]
63.055
4.832
67.993
5.186
67.359
5.242
66.776
5.037
64.870
4.920
71.339
5.297
67.512
5.188
63.486
5.172
64.264
5.265
57.637
4.701
71.954
5.718
68.644
5.427
62.285
4.849
71.656
5.474
71.205
5.282
67.934
5.258
68.369
5.593
69.804
5.529

67.008
3.814
5.692
57.637
71.954
18

5.221
0.275
5.271
4.701
5.718
18

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Unnotched Tension Properties (UNT2) -- (RTD)


Normalized Strength
Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

Cure Cycle #

1
1

Prepreg Lot #

0
0

20

40

60

80

100

120

Laminate Tension Strength (UNT2) [ksi]

Laminate Unnotched Tension Properties (UNT2) -- (RTD)


Normalized Modulus

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

0
0.0

1.0

2.0

3.0

4.0

5.0

Laminate Tension Modulus (UNT2) [Msi]

Page 148 of 238

6.0

7.0

8.0

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A


Laminate Unnotched Tension Properties (UNT2) -- (ETW)
Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Hexcel Hexcel Cure Prepreg Cure Cycle Strength Modulus Avg. Specimen # Plies in
Failure
Number
Batch #
Cycle
Lot #
#
[ksi]
[Msi]
Thickn. [in]
Laminate
Mode
HFIBA11DD
A
M1
1
1
53.540
4.284
0.148
20
DGM
HFIBA11ED
A
M1
1
1
54.012
4.422
0.146
20
DGM
HFIBA11FD
A
M1
1
1
50.226
4.323
0.146
20
DGM
HFIBA11GD
A
M1
1
1
51.145
4.285
0.146
20
DGM
HFIBA21BD
A
M2
1
2
54.794
4.473
0.148
20
DGM
HFIBA21CD
A
M2
1
2
52.714
4.318
0.147
20
DGM
HFIBA21DD
A
M2
1
2
54.527
4.454
0.145
20
DGM
HFIBB1X5D*
B
M1
2
1
56.418
4.466
0.142
20
DGM
HFIBB1X6D*
B
M1
2
1
54.904
4.427
0.143
20
DGM
HFIBB21ED
B
M2
2
2
52.034
4.479
0.146
20
DGM
HFIBB21FD
B
M2
2
2
55.349
4.482
0.146
20
DGM
HFIBB21GD
B
M2
2
2
52.600
4.487
0.146
20
DGM
HFIBC11CD
C
M1
3
1
52.726
4.307
0.147
20
DGM
HFIBC11DD
C
M1
3
1
54.608
4.394
0.145
20
DGM
HFIBC11ED
C
M1
3
1
53.866
4.284
0.145
20
DGM
HFIBC21BD
C
M2
3
2
52.347
4.509
0.148
20
DGM
HFIBC21CD
C
M2
3
2
52.559
4.473
0.147
20
DGM
HFIBC21DD
C
M2
3
2
53.588
4.510
0.146
20
DGM
*PANEL WAS NOT REPLACED BECAUSE OF INSUFICENT MATERIAL. SPECIMENS WERE TAKEN FROM UNC2 PANEL.
Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

53.442
1.550
2.901
50.226
56.418
18

4.410
0.085
1.930
4.284
4.510
18

Page 149 of 238

Average norm
Standard Dev.norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Avg. tply Strengthnorm Modulusnorm


[in]
[ksi]
[Msi]
0.0074
54.928
4.395
0.0073
54.775
4.484
0.0073
50.965
4.387
0.0073
51.985
4.356
0.0074
56.126
4.582
0.0073
53.685
4.398
0.0073
54.963
4.489
0.0071
55.615
4.402
0.0071
54.390
4.385
0.0073
52.606
4.528
0.0073
56.233
4.553
0.0073
53.440
4.559
0.0074
53.983
4.409
0.0072
54.905
4.418
0.0073
54.390
4.325
0.0074
53.940
4.646
0.0074
53.703
4.570
0.0073
54.394
4.577

0.0073

0.0071
0.0074

54.168
1.350
2.492
50.965
56.233
18

4.470
0.095
2.127
4.325
4.646
18

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Unnotched Tension Properties (UNT2) -- (ETW)


Normalized Strength
HEXCEL 8552 - IM7 UNI PREPREG

Cure Cycle #
Prepreg Lot #

3
2
2
1

Prepreg Lot #

Cure Cycle #

0
0

20

40

60

80

100

120

LaminateTension Strength (UNT2) [ksi]

Laminate Unnotched Tension Properties (UNT2) -- (ETW)


Normalized Modulus

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

0
0.0

1.0

2.0

3.0

4.0

5.0

Laminate Tension Modulus (UNT2) [Msi]

Page 150 of 238

6.0

7.0

8.0

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

4.10 Unnotched Tension 3 Properties


Laminate Unnotched Tension Properties (UNT3) -- (CTD)
Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFICA116B
HFICA117B
HFICA118B
HFICA119B
HFICA215B
HFICA216B
HFICA217B
HFICB115B
HFICB116B
HFICB117B
HFICB214B
HFICB216B
HFICB217B
HFICC115B
HFICC116B
HFICC117B
HFICC215B
HFICC216B
HFICC217B

Hexcel Hexcel Cure


Batch #
Cycle
A
M1
A
M1
A
M1
A
M1
A
M2
A
M2
A
M2
B
M1
B
M1
B
M1
B
M2
B
M2
B
M2
C
M1
C
M1
C
M1
C
M2
C
M2
C
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

Strength
[ksi]
173.739
165.963
166.866
161.608
163.835
170.370
178.529
177.874
178.969
176.503
178.802
160.819
181.762
169.266
180.101
166.222
185.159
164.960
187.845

Average 173.115
Standard Dev.
8.207
Coeff. of Var. [%]
4.741
Min. 160.819
Max. 187.845
Number of Spec.
19

Modulus
[Msi]
12.884
13.282
12.669
12.952
12.356
12.971
12.824
13.058
13.237
12.829
13.116
12.705
13.411
12.837
13.162
13.379
13.384
13.250
13.168

Avg. Specimen # Plies in


Thickn. [in]
Laminate
0.145
20
0.145
20
0.147
20
0.147
20
0.146
20
0.146
20
0.146
20
0.143
20
0.143
20
0.144
20
0.144
20
0.143
20
0.144
20
0.146
20
0.146
20
0.146
20
0.143
20
0.143
20
0.145
20

13.025
0.282
2.166
12.356
13.411
19

Page 151 of 238

Failure
Mode
AWT
DWT /LWT / LAB
LAB / DAB
LWB
DGM /LAT / AWT
DGM /AWB /AAT
DGM /LAB /AWT
LWT / DGM
LAT /LAB / DGM
LAT / LWB
DGM/LWT/LWB
LAB / LWT
LAB
AGM / DGM
LAT / LWB
LWB
LWT / LWB
LWT
LWT / LWB

Avg. tply Strengthnorm


[in]
[ksi]
0.0073
175.368
0.0072
166.559
0.0073
170.188
0.0073
164.863
0.0073
166.660
0.0073
172.776
0.0073
180.595
0.0072
176.638
0.0072
177.829
0.0072
176.197
0.0072
179.029
0.0072
159.907
0.0072
181.362
0.0073
172.028
0.0073
182.957
0.0073
168.973
0.0072
184.452
0.0072
164.177
0.0072
188.802

Average norm 0.0072


Standard Dev. norm
Coeff. of Var. [%]norm
Min.
0.0072
Max.
0.0073
Number of Spec.

174.177
7.790
4.472
159.907
188.802
19

Modulusnorm
[Msi]
13.005
13.329
12.921
13.213
12.569
13.154
12.972
12.967
13.153
12.807
13.132
12.633
13.381
13.047
13.370
13.600
13.333
13.187
13.235

13.106
0.260
1.985
12.569
13.600
19

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Unnotched Tension Properties (UNT3) -- (CTD)


Normalized Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

Prepeg Lot #

Cure Cycle #

0
0

50

100

150

200

250

300

Laminate Tension Strength (UNT3) [ksi]

Laminate Unnotched Tension Properties (UNT3) -- (CTD)


Normalized Modulus

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

0
0.0

5.0

10.0

15.0

Laminate Tension Modulus (UNT3) [Msi]

Page 152 of 238

20.0

25.0

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Unnotched Tension Properties (UNT3) -- (RTD)


Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen Hexcel Hexcel Cure Prepreg
Number
Batch #
Cycle
Lot #
HFICA112A
A
M1
1
HFICA113A
A
M1
1
HFICA114A
A
M1
1
HFICA115A
A
M1
1
HFICA211A
A
M2
1
HFICA212A
A
M2
1
HFICA213A
A
M2
1
HFICA214A
A
M2
1
HFICB111A
B
M1
2
HFICB112A
B
M1
2
HFICB113A
B
M1
2
HFICB114A
B
M1
2
HFICB211A
B
M2
2
HFICB212A
B
M2
2
HFICB213A
B
M2
2
HFICC111A
C
M1
3
HFICC112A
C
M1
3
HFICC113A
C
M1
3
HFICC211A
C
M2
3
HFICC212A
C
M2
3
HFICC213A
C
M2
3
HFICC214A
C
M2
3

Cure Cycle
#
1
1
1
1
2
2
2
2
1
1
1
1
2
2
2
1
1
1
2
2
2
2

Strength
[ksi]
170.864
172.992
178.974
158.489
170.462
172.953
167.997
175.427
190.858
181.054
175.890
183.397
185.538
174.416
177.385
166.230
182.653
180.532
170.513
176.813
176.746
186.723

Average 176.223
Standard Dev.
7.423
Coeff. of Var. [%]
4.212
Min. 158.489
Max. 190.858
Number of Spec.
22

Modulus Avg. Specimen # Plies in


Failure
[Msi]
Thickn. [in]
Laminate
Mode
13.556
0.145
20
DGM / LGM
12.827
0.147
20
DGM / LGM
12.978
0.145
20
DGM / LWT
12.642
0.145
20
LAB
14.775
0.137
20
LAT / LWB
14.363
0.147
20
DGM / LAT
12.824
0.147
20
LGM
12.782
0.146
20
DGM / LWT
13.423
0.137
20
DGM / LAT
12.986
0.145
20
DGM / LAT
13.232
0.145
20
DGM / LAT/ LAB
13.273
0.144
20
AGM / AWB
13.003
0.137
20
DGM /LWT / LWB
13.331
0.145
20
DGM / AGM
13.042
0.145
20
DGM / AGM
12.920
0.139
20
LWT / LAB / DGM
13.380
0.148
20
AGM / DGM
14.836
0.147
20
AGM / DGM
13.121
0.135
20
LWB/AWB/LAT
13.211
0.144
20
DGM /LWT /LWB
11.400
0.145
20
DGM / LGM
12.437
0.144
20
DGM / LGM
13.197
0.743
5.626
11.400
14.836
22

Page 153 of 238

Average norm
Standard Dev.norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Avg. tply
[in]
0.0073
0.0074
0.0072
0.0072
0.0069
0.0073
0.0074
0.0073
0.0068
0.0072
0.0072
0.0072
0.0068
0.0072
0.0073
0.0069
0.0074
0.0073
0.0068
0.0072
0.0073
0.0072

Strengthnorm
[ksi]
172.525
177.157
179.844
159.040
162.294
176.276
171.905
177.274
180.917
182.018
176.521
183.269
176.025
175.183
178.946
159.977
188.001
184.064
160.330
177.079
178.280
186.852

Modulusnorm
[Msi]
13.688
13.136
13.041
12.686
14.067
14.639
13.122
12.916
12.724
13.055
13.279
13.264
12.336
13.390
13.157
12.434
13.772
15.127
12.337
13.231
11.499
12.446

0.0072

175.626
8.388
4.776
159.040
188.001
22

13.152
0.795
6.043
11.499
15.127
22

0.0068
0.0074

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Unnotched Tension Properties (UNT3) -- (RTD)


Normalized Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

Prepeg Lot #

Cure Cycle #

0
0

50

100

150

200

250

300

Laminate Tension Strength (UNT3) [ksi]

Laminate Unnotched Tension Properties (UNT3) -- (RTD)


Normalized Modulus

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

0
0.0

10.0

20.0

30.0

Laminate Tension Modulus (UNT3) [Msi]

Page 154 of 238

40.0

50.0

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Unnotched Tension Properties (UNT3) -- (ETW)


Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen Hexcel Hexcel Cure Prepreg Cure Cycle
Number
Batch #
Cycle
Lot #
#
HFICA11AD
A
M1
1
1
HFICA11CD
A
M1
1
1
HFICA11DD
A
M1
1
1
HFICA11ED
A
M1
1
1
HFICA21AD
A
M1
1
2
HFICA219D
A
M2
1
2
HFICA21BD
A
M2
1
2
HFICA21CD
A
M2
1
2
HFICB118D*
B
M0
2
1
HFICB119D
B
M1
2
1
HFICB11AD
B
M1
2
1
HFICB11BD
B
M1
2
1
HFICB218D
B
M2
2
2
HFICB219D
B
M2
2
2
HFICB21AD
B
M2
2
2
HFICC118D
C
M1
3
1
HFICC119D
C
M1
3
1
HFICC11AD
C
M1
3
1
HFICC218D*
C
M1
3
2
HFICC219D
C
M2
3
2
HFICC21BD
C
M2
3
2
HFICC21CD
C
M2
3
2
* Specimen had a bad failure so strength was excluded
Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength Modulus Avg. Specimen # Plies in


Failure
[ksi]
[Msi]
Thickn. [in]
Laminate
Mode
195.340
13.192
0.135
20
LWB/LWT
172.304
13.105
0.146
20
LGM/AGM
195.017
12.585
0.148
20
DGM/AGM
175.968
12.931
0.145
20
DGM/LWB/LWT
12.979
0.137
20
LIT
189.435
13.106
0.148
20
LGM
172.460
12.478
0.135
20
LWT / LWB
193.503
12.780
0.146
20
DGM/LWT / LWB
13.473
0.144
20
*
182.419
13.673
0.145
20
LAT/LAB/DGM
190.108
13.006
0.144
20
AGM
196.122
12.837
0.145
20
AGM
185.097
13.903
0.149
20
DGM/AGM
189.991
13.228
0.145
20
DGM/LAT
180.302
13.108
0.144
20
AGM/DGM
199.333
13.508
0.147
20
LWB/LGM
191.362
13.319
0.139
20
LWB/DGM
195.315
13.294
0.147
20
DGM/LWT
13.544
0.144
20
*
187.265
13.008
0.146
20
DGM/AGM
180.648
12.859
0.136
20
LAT/LAB
186.654
13.470
0.147
20
DGM/LWB
187.297
8.102
4.326
172.304
199.333
19

13.154
0.352
2.676
12.478
13.903
22

Page 155 of 238

Average norm
Standard Dev. norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Avg. tply Strengthnorm Modulusnorm


[in]
[ksi]
[Msi]
0.0068
183.448
12.389
0.0073
174.896
13.302
0.0074
199.847
12.897
0.0073
177.476
13.042
0.0069
12.388
0.0074
194.982
13.490
0.0067
161.561
11.690
0.0073
196.840
13.000
0.0072
13.482
0.0072
183.242
13.735
0.0072
190.680
13.045
0.0072
196.893
12.887
0.0075
191.824
14.409
0.0072
191.002
13.299
0.0072
180.051
13.090
0.0073
203.394
13.783
0.0069
184.252
12.824
0.0074
199.995
13.612
0.0072
13.568
0.0073
189.953
13.195
0.0068
170.905
12.165
0.0073
189.916
13.706
0.0072

0.0067
0.0075

187.429
10.938
5.836
161.561
203.394
19

13.136
0.611
4.652
11.690
14.409
22

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Unnotched Tension Properties (UNT3) -- (ETW)


Normalized Strength
HEXCEL 8552 - IM7 UNI PREPREG

Cure Cycle #
Prepreg Lot #

Prepeg Lot #

Cure Cycle #

3
2

0
0

50

100

150

200

250

300

350

400

Laminate Tension Strength (UNT3) [ksi]

Laminate Unnotched Tension Properties (UNT3) -- (ETW)


Normalized Modulus
HEXCEL 8552 - IM7 UNI PREPREG

Cure Cycle #
Prepreg Lot #

3
2
2
1
1

0
0.0

5.0

10.0

15.0

Laminate Tension Modulus (UNT3) [Msi]

Page 156 of 238

20.0

25.0

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

4.11 Unnotched Compression 1 Properties


Laminate Unnotched Compression Properties (UNC1) -- (RTD)
Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen Hexcel Hexcel Cure Prepreg
Cure Cycle
Number
Batch #
Cycle
Lot #
Batch #
HFIWA111A
A
M1
1
1
HFIWA112A
A
M1
1
1
HFIWA113A
A
M1
1
1
HFIWA114A
A
M1
1
1
HFIWA211A
A
M2
1
2
HFIWA212A
A
M2
1
2
HFIWA213A
A
M2
1
2
HFIWB111A
B
M1
2
1
HFIWB112A
B
M1
2
1
HFIWB113A
B
M1
2
1
HFIWB211A
B
M2
2
2
HFIWB212A
B
M2
2
2
HFIWB213A
B
M2
2
2
HFIWC111A
C
M1
3
1
HFIWC112A
C
M1
3
1
HFIWC113A
C
M1
3
1
HFIWC211A
C
M2
3
2
HFIWC212A
C
M2
3
2
HFIWC213A
C
M2
3
2
Batch B Cure Cycle 1 has improper layup so results were removed

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength
[ksi]
82.117
96.785
90.832
84.912
91.192
92.530
91.329

Modulus
[Msi]
7.418
7.671
7.440
7.199
7.711
7.739
7.602

Poisson's
Ratio
0.290
0.320
0.310
0.304
0.338
0.367
0.354

Avg. Specimen
Thickn. [in]
0.107
0.116
0.119
0.120
0.114
0.118
0.119

# Plies in
Laminate
16
16
16
16
16
16
16

Failure
Mode
BGM
BGM
BGM
BGM
BGM
BGM
BGM

Avg. tply
[in]
0.0067
0.0072
0.0074
0.0075
0.0071
0.0074
0.0074

Strengthnorm
[ksi]
76.272
97.037
93.855
88.081
90.532
95.127
94.289

Modulusnorm
[Msi]
6.890
7.690
7.688
7.467
7.655
7.957
7.848

73.465
91.759
74.784
88.972
86.634
79.952
85.577
91.348
89.030

8.612
8.485
8.092
8.245
8.125
7.841
7.884
7.933
7.781

0.314
0.348
0.336
0.314
0.341
0.349
0.339
0.356
0.360

0.107
0.114
0.117
0.112
0.119
0.119
0.110
0.116
0.117

16
16
16
16
16
16
16
16
16

BGM
BGM
BGM
BGM
BGM
BGM
BGM
BGM
BGM

0.0067
0.0071
0.0073
0.0070
0.0075
0.0074
0.0069
0.0072
0.0073

68.065
90.538
75.660
86.745
89.642
82.427
81.875
91.797
90.782

7.979
8.372
8.187
8.039
8.407
8.084
7.543
7.972
7.934

out

check for extras

0.0072

87.045
8.111
9.318
68.065
97.037
16

86.951
6.529
7.508
73.465
96.785
16

7.861
0.382
4.861
7.199
8.612
16

0.334
0.022
6.705
0.290
0.367
16

Page 157 of 238

Average norm
Standard Dev. norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

0.0067
0.0075
16

7.857
0.373
4.749
6.890
8.407
16

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Unnotched Compression Properties (UNC1) -- (RTD)


Normalized Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
2

Prepreg Lot #

Cure Cycle #

0
0

25

50

75

100

125

150

Laminate Compression Strength (UNC1) [ksi]

Laminate Unnotched Compression Properties (UNC1) -- (RTD)


Normalized Modulus

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
2

0
0.0

2.0

4.0

6.0

8.0

10.0

Laminate Compression Modulus (UNC1) [Msi]

Page 158 of 238

12.0

14.0

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Unnotched Compression Properties (UNC1) -- (ETW)


Strength & Modulus
HEXCEL 8552 - IM7 UNI PREPREG

normalizing tply
[in]
0.0072

Specimen
Hexcel
Hexcel Cure Prepreg Cure Cycle Strength Modulus Poisson's Avg. Specimen # Plies in
Failure
Avg. tply Strengthnorm
Number
Batch #
Cycle
Lot #
#
[ksi]
[Msi]
Ratio
Thickn. [in]
Laminate
Mode
[in]
[ksi]
HFIWA11DD
A
M1
1
1
54.607
7.001
0.369
0.118
16
BGM
0.0074
55.744
HFIWA11ED
A
M1
1
1
59.118
6.924
0.356
0.118
16
BGM
0.0074
60.555
HFIWA11FD
A
M1
1
1
51.227
7.240
0.356
0.116
16
BGM
0.0073
51.605
HFIWA115D
A
M1
1
1
51.738
6.987
0.362
0.118
16
BGM
0.0074
52.958
HFIWA214D
A
M2
1
2
64.777
6.971
0.334
0.118
16
BGM
0.0073
66.071
HFIWA215D
A
M2
1
2
58.623
6.817
0.367
0.117
16
BAB
0.0073
59.284
HFIWA216D
A
M2
1
2
51.583
6.791
0.375
0.116
16
BGM / DGM
0.0073
52.046
HFIWB21CD
B
M2
2
1
58.036
7.198
0.379
0.115
16
DGM / BGM
0.0072
57.726
HFIWB216D
B
M2
2
1
56.134
7.126
0.350
0.115
16
HGM
0.0072
55.874
HFIWB2RMD
B
M2
2
1
61.874
6.905
0.354
0.117
16
DGM / BGM
0.0073
62.841
HFIWC11AD
C
M1
3
1
52.051
7.024
0.359
0.117
16
DGM
0.0073
52.804
HFIWC11BD
C
M1
3
1
56.854
7.040
0.356
0.117
16
BGM
0.0073
57.520
HFIWC11CD
C
M1
3
1
50.531
7.184
0.317
0.116
16
BGM
0.0073
51.065
HFIWC21AD
C
M2
3
2
49.367
7.204
0.339
0.115
16
DGM
0.0072
49.345
HFIWC21BD
C
M2
3
2
50.270
7.375
0.361
0.115
16
BAT
0.0072
50.059
HFIWC21CD
C
M2
3
2
48.540
7.136
0.369
0.116
16
BGM
0.0072
48.716
HFIWA118D
A
M1
1
1
70.392
0.117
16
BGM
0.0073
71.543
HFIWA119D
A
M1
1
1
70.983
0.117
16
BGM
0.0073
72.226
HFIWA11AD*
A
M1
1
1
56.125
0.117
16
BGM
0.0073
57.075
HFIWA11BD*
A
M1
1
1
58.329
0.118
16
BGM
0.0073
59.511
HFIWA11CD*
A
M1
1
1
0.117
16
HIB
0.0073
HFIWA217D*
A
M2
1
2
55.250
0.117
16
HAB
0.0073
56.130
HFIWA218D*
A
M2
1
2
58.901
0.117
16
BGM
0.0073
60.009
HFIWA219D*
A
M2
1
2
54.659
0.117
16
HGM
0.0073
55.735
HFIWB217D
B
M2
2
2
54.624
0.115
16
BGM
0.0072
54.339
HFIWB218D
B
M2
2
2
69.184
0.115
16
HGM
0.0072
69.194
HFIWB219D
B
M2
2
2
64.638
0.115
16
BGM
0.0072
64.563
HFIWB21AD
B
M2
2
2
62.823
0.115
16
HAT
0.0072
62.569
HFIWB21BD
B
M2
2
2
0.115
16
HIT
HFIWC117D*
C
M1
3
1
0.117
16
BGM
HFIWC118D*
C
M1
3
1
55.329
0.117
16
BAB
0.0073
56.065
HFIWC119D
C
M1
3
1
55.844
0.117
16
HAB
0.0073
56.636
HFIWC217D*
C
M2
3
2
50.176
0.116
16
HAT
0.0072
50.452
HFIWC218D*
C
M2
3
2
0.117
16
HAB
HFIWC219D*
C
M2
3
2
0.117
16
HAT
Compressive Strength is not reported for HFIWB 116D as unacceptable failure mode was observed
STRENGTH WAS NOT REPORTED FOR SPECIMENS HFIWA11CD and HFIWB21BD DUE TO AN UNACCEPTABLE FAILURE MODE.
Shaded specimens had modulus removed due to improper strain gage adhesive used
Batch B Cure Cycle 1 has improper layup so results were removed
* Specimens have uneven grip marks due to thickness variation
Average 57.086
7.058
0.356
Average norm 0.0073
57.675
Standard Dev. 6.207
0.161
0.016
Standard Dev. norm
6.355
Coeff. of Var. [%] 10.872
2.282
4.424
Coeff. of Var. [%]norm
11.019
Min. 48.540
6.791
0.317
Min.
0.0072
48.716
Max. 70.983
7.375
0.379
Max.
0.0074
72.226
Number of Spec.
30
16
16
Number of Spec.
31
30

Page 159 of 238

Modulusnorm
[Msi]
7.147
7.093
7.293
7.152
7.111
6.894
6.852
7.159
7.093
7.013
7.126
7.122
7.260
7.201
7.344
7.161

7.126
0.128
1.801
6.852
7.344
16

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Unnotched Compression Properties (UNC1) -- (ETW)


Normalized Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
2

Prepreg Lot #

Cure Cycle #

0
0

25

50

75

100

125

150

Laminate Compression Strength (UNC1) [ksi]

Laminate Unnotched Compression Properties (UNC1) -- (ETW)


Normalized Modulus

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
2

0
0.0

2.0

4.0

6.0

8.0

Laminate Compression Modulus (UNC1) [Msi]

Page 160 of 238

10.0

12.0

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

4.12 Unnotched Compression 2 Properties


Laminate Unnotched Compression Properties (UNC2) -- (RTD)
Strength & Modulus
HEXCEL 8552 - IM7 UNI PREPREG

normalizing tply
[in]
0.0072

Specimen Hexcel Hexcel Cure Prepreg Cure Cycle Strength Modulus Poisson's Avg. Specimen # Plies in Failure
Avg. tply Strengthnorm Modulusnorm
Number
Batch #
Cycle
Lot #
#
[ksi]
[Msi]
Ratio
Thickn. [in]
Laminate
Mode
[in]
[ksi]
[Msi]
HFIXA111A
A
M1
1
1
73.013
4.789
0.535
0.136
20
BGM
0.0068
69.151
4.536
HFIXA112A
A
M1
1
1
71.811
4.938
0.566
0.144
20
BGM
0.0072
71.720
4.932
HFIXA113A
A
M1
1
1
64.461
4.672
0.562
0.148
20
BGM
0.0074
66.125
4.793
HFIXA114A
A
M1
1
1
70.533
4.578
0.581
0.148
20
BGM
0.0074
72.615
4.713
HFIXA211A
A
M2
1
2
60.868
4.598
0.563
0.136
20
BGM
0.0068
57.627
4.353
HFIXA212A
A
M2
1
2
63.297
5.027
0.608
0.143
20
BGM
0.0071
62.652
4.976
HFIXA213A
A
M2
1
2
68.035
4.955
0.612
0.147
20
BGM
0.0073
69.302
5.047
HFIXB111A
B
M1
2
1
67.082
5.303
0.664
0.144
20
BGM
0.0072
66.849
5.284
HFIXB112A
B
M1
2
1
65.716
5.328
0.675
0.145
20
BGM
0.0072
65.975
5.349
HFIXB113A
B
M1
2
1
64.557
5.251
0.662
0.146
20
BGM
0.0073
65.394
5.319
HFIXB211A*
B
M2
2
2
64.745
5.202
0.546
0.133
20
BGM
0.0066
59.747
4.800
HFIXB212A
B
M2
2
2
69.508
5.141
0.587
0.141
20
BGM
0.0070
67.818
5.016
HFIXB213A
B
M2
2
2
70.542
4.844
0.563
0.145
20
BGM
0.0072
70.836
4.864
HFIXC211A*
C
M2
3
2
63.253
4.847
0.514
0.130
20
BGM
0.0065
57.294
4.390
HFIXC212A
C
M2
3
2
70.328
5.092
0.574
0.139
20
BGM
0.0069
67.862
4.914
HFIXC213A
C
M2
3
2
72.077
5.046
0.572
0.144
20
BGM
0.0072
72.085
5.046
For batch C, cure cycle 1 panel has wrong layup, has two -45 degree plies at beginning of layup.
*Specimens have thickness taper at edge of coupon
Average 67.489
4.976
0.587
Average norm 0.0071
66.441
4.896
Standard Dev. 3.735
0.241
0.047
Standard Dev.norm
4.890
0.299
Coeff. of Var. [%] 5.534
4.842
7.960
Coeff. of Var. [%]norm
7.360
6.100
Min. 60.868
4.578
0.514
Min.
0.0065
57.294
4.353
Max. 73.013
5.328
0.675
Max.
0.0074
72.615
5.349
Number of Spec.
16
16
16
Number of Spec.
16
16

Page 161 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Unnotched Compression Properties (UNC2) -- (RTD)


Normalized Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
2

Prepreg Lot #

Cure Cycle #

0
0

10

20

30

40

50

60

70

80

90

Laminate Compression Strength (UNC2) [ksi]

Laminate Unnotched Compression Properties (UNC2) -- (RTD)


Normalized Modulus

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2

0
0.0

1.0

2.0

3.0

4.0

5.0

Laminate Compression Modulus (UNC2) [Msi]

Page 162 of 238

6.0

7.0

8.0

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Unnotched Compression Properties (UNC2) -- (ETW)


Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen Hexcel Hexcel Cure Prepreg Cure Cycle Strength Modulus* Poisson's Avg. Specimen # Plies in
Number
Batch #
Cycle
Lot #
#
[ksi]
[Msi]
Ratio
Thickn. [in]
Laminate
HFIXA11DD
A
M1
1
1
37.314
3.847
0.641
0.148
20
HFIXA11ED
A
M1
1
1
34.936
3.910
0.642
0.149
20
HFIXA11FD
A
M1
1
1
41.150
4.149
0.673
0.147
20
HFIXA115D
A
M1
1
1
40.617
3.860
0.659
0.148
20
HFIXA21AD
A
M2
1
2
36.826
3.967
0.670
0.146
20
HFIXA21BD
A
M2
1
2
36.576
4.173
0.698
0.146
20
HFIXA21CD
A
M2
1
2
34.595
4.077
0.685
0.146
20
HFIXB119D
B
M1
2
1
41.295
4.131
0.690
0.143
20
HFIXB11AD
B
M1
2
1
41.878
4.145
0.671
0.143
20
HFIXB114D
B
M1
2
1
42.303
4.182
0.695
0.146
20
HFIXB21BD
B
M2
2
2
35.933
4.115
0.654
0.143
20
HFIXB21CD
B
M2
2
2
34.825
4.005
0.646
0.143
20
HFIXB214D
B
M2
2
2
38.605
4.038
0.669
0.145
20
HFIXC21AD
C
M2
3
2
31.309
4.077
0.655
0.143
20
HFIXC21BD
C
M2
3
2
35.807
4.158
0.661
0.143
20
HFIXC214D
C
M2
3
2
42.616
4.108
0.631
0.145
20
HFIXA118D
A
M1
1
1
49.443
0.147
20
HFIXA119D
A
M1
1
1
44.763
0.146
20
HFIXA11AD
A
M1
1
1
46.375
0.146
20
HFIXA11BD
A
M1
1
1
42.111
0.146
20
HFIXA217D
A
M2
1
2
37.693
0.145
20
HFIXA218D
A
M2
1
2
42.187
0.145
20
HFIXA219D
A
M2
1
2
42.274
0.146
20
HFIXB116D
B
M1
2
1
37.228
0.137
20
HFIXB117D
B
M1
2
1
40.263
0.142
20
HFIXB118D
B
M1
2
1
40.542
0.142
20
HFIXB217D
B
M2
2
2
47.639
0.143
20
HFIXB218D
B
M2
2
2
45.032
0.143
20
HFIXB219D
B
M2
2
2
46.851
0.143
20
HFIXC217D
C
M2
3
2
40.333
0.143
20
HFIXC218D
C
M2
3
2
0.142
20
HFIXC219D
C
M2
3
2
43.987
0.144
20
HFIXC218D: STRENGTH REMOVED DUE TO A BAD FAILURE MODE
For batch C, cure cycle 1 panel has wrong layup, has two -45 degree plies at beginning of layup.
* Modulus removed due to improper strain gage adhesvie used
Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

40.429
4.330
10.710
31.309
49.443
31

4.059
0.111
2.723
3.847
4.182
16

0.665
0.020
3.029
0.631
0.698
16

Page 163 of 238

Failure
Mode
DGM
DGM
DGM
DGM
DGM
BGM
DGM
DGM
DGM
DGM
BGM/DGM
DGM
DGM
DGM
DGM
DGM
BGM
BGM
BGM
BGM
BGM
BGM
BGM
BAB
BGM
BGM
BGM
BGM
BGM
BGM
BGM / CIB
BGM

Average norm
Standard Dev.norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Avg. tply Strengthnorm


[in]
[ksi]
0.0074
38.415
0.0074
36.137
0.0074
42.008
0.0074
41.735
0.0073
37.256
0.0073
37.037
0.0073
35.156
0.0072
41.094
0.0072
41.723
0.0073
42.949
0.0071
35.622
0.0072
34.692
0.0073
38.941
0.0072
31.189
0.0072
35.608
0.0072
42.828
0.0073
50.336
0.0073
45.530
0.0073
47.131
0.0073
42.794
0.0072
37.855
0.0073
42.480
0.0073
42.910
0.0069
35.444
0.0071
39.597
0.0071
40.068
0.0071
47.303
0.0071
44.657
0.0072
46.575
0.0071
40.007
0.0071
0.0072
43.921

0.0072

0.0069
0.0074
32

40.613
4.430
10.907
31.189
50.336
31

Modulusnorm
[Msi]
3.961
4.045
4.235
3.967
4.013
4.225
4.143
4.111
4.130
4.246
4.080
3.990
4.073
4.062
4.135
4.129

4.096
0.090
2.206
3.961
4.246
16

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Unnotched Compression Properties (UNC2) -- (ETW)


Normalized Strength
HEXCEL 8552 - IM7 UNI PREPREG
3
Cure Cycle #

2
2

0
0

10

20

30

40

50

60

70

80

90

Laminate Compression Strength (UNC2) [ksi]

Laminate Unnotched Compression Properties (UNC2) -- (ETW)


Normalized Modulus
HEXCEL 8552 - IM7 UNI PREPREG
3
3

Prepreg Lot #

2
2

0
0.0

1.0

2.0

3.0

4.0

5.0

6.0

Laminate Compression Modulus (UNC2) [Msi]

Page 164 of 238

7.0

8.0

Prepreg Lot #

Cure Cycle #

Cure Cycle #

Prepreg Lot #

Cure Cycle #

Prepreg Lot #

CAM-RP-2009-015 April 22, 2011 Revision A

4.13 Unnotched Compression 3 Properties

Laminate Unnotched Compression Properties (UNC3) -- (RTD)


Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen Hexcel Hexcel Cure Prepreg Cure Cycle Strength Modulus
Number
Batch #
Cycle
Lot #
#
[ksi]
[Msi]
HFIYA112A
A
M1
1
1
12.739
HFIYA113A
A
M1
1
1
128.027
11.653
HFIYA114A
A
M1
1
1
121.763
11.980
HFIYA115A
A
M1
1
1
122.888
11.373
HFIYA116A
A
M1
1
1
115.332
12.483
HFIYA211A
A
M2
1
2
117.385
11.196
HFIYA212A
A
M2
1
2
123.466
11.659
HFIYA213A
A
M2
1
2
118.442
11.807
HFIYB111A*
B
M1
2
1
HFIYB112A
B
M1
2
1
122.753
12.304
HFIYB113A
B
M1
2
1
137.699
12.005
HFIYB2C1A*
B
M2
2
2
HFIYB2C2A
B
M2
2
2
116.554
11.926
HFIYB2C3A
B
M2
2
2
112.003
11.984
HFIYC111A
C
M1
3
1
118.911
12.436
HFIYC112A
C
M1
3
1
111.743
11.642
HFIYC113A
C
M1
3
1
116.408
11.601
HFIYC211A*
C
M2
3
2
HFIYC212A
C
M2
3
2
126.639
11.970
HFIYC213A
C
M2
3
2
127.022
12.114
*Specimens have thickness taper at end of specimen
Average 121.065
Standard Dev. 6.699
Coeff. of Var. [%] 5.533
Min. 111.743
Max. 137.699
Number of Spec.
16

11.934
0.404
3.383
11.196
12.739
17

Poisson's Avg. Specimen # Plies in


Ratio
Thickn. [in]
Laminate
0.452
0.141
20
0.394
0.146
20
0.382
0.147
20
0.404
0.146
20
0.433
0.145
20
0.384
0.133
20
0.443
0.141
20
0.453
0.146
20
0.430
0.412

0.138
0.142

0.439
0.450
0.438
0.412
0.422

0.143
0.144
0.143
0.150
0.147

20
20
20
20
20
20
20
20

0.399
0.436

0.141
0.146

20
20

0.423
0.024
5.596
0.382
0.453
17

Page 165 of 238

Failure
Mode
END CRUSH
BGM
BGM
BGM
BGM
BGM
BGM
BGM

Avg. tply
[in]
0.0070
0.0073
0.0074
0.0073
0.0073
0.0066
0.0071
0.0073

Strengthnorm
[ksi]
129.969
124.426
124.566
116.227
108.201
120.994
120.348

Modulusnorm
[Msi]
12.451
11.830
12.242
11.528
12.579
10.320
11.426
11.997

BGM
BGM
BGM
BGM
BGM
BGM
BGM
BGM

0.0069
0.0071

117.226
136.089

11.750
11.865

0.0072
0.0072
0.0072
0.0075
0.0074

115.974
111.666
118.456
116.631
119.143

11.866
11.947
12.389
12.151
11.873

BGM
BGM

0.0071
0.0073

124.279
129.183

11.747
12.320

0.0072

120.836
7.083
5.862
108.201
136.089
16

11.899
0.518
4.350
10.320
12.579
17

Average norm
Standard Dev. norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

0.0066
0.0075
17

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Unnotched Compression Properties (UNC3) -- (RTD)


Normalized Strength
HEXCEL 8552 - IM7 UNI PREPREG

Cure Cycle #
Prepreg Lot #

Cure Cycle #

2
1
1

Prepreg Lot #

3
2

0
0

20

40

60

80

100

120

140

160

Laminate Compression Strength (UNC3) [ksi]

Laminate Unnotched Compression Properties (UNC3) -- (RTD)


Normalized Modulus

Cure Cycle #
Prepreg Lot #

HEXCEL 8552 - IM7 UNI PREPREG

3
2
2
1
1

0
0.0

2.0

4.0

6.0

8.0

10.0

Laminate Compression Modulus (UNC3) [Msi]

Page 166 of 238

12.0

14.0

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Unnotched Compression Properties (UNC3) -- (ETW)


Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen Hexcel Hexcel Cure Prepreg Cure Cycle Strength Modulus Poisson's Avg. Specimen # Plies in
Number
Batch #
Cycle
Lot #
#
[ksi]
[Msi]
Ratio
Thickn. [in]
Laminate
HFIYA111D*
A
M1
1
1
0.132
20
HFIYA117D
A
M1
1
1
11.218
0.420
0.144
20
HFIYA21BD
A
M2
1
2
11.351
0.414
0.146
20
HFIYA21CD
A
M2
1
2
11.407
0.434
0.146
20
HFIYA214D
A
M2
1
2
11.597
0.450
0.148
20
HFIYB118D
B
M1
2
1
78.090
11.699
0.415
0.142
20
HFIYB11CD
B
M1
2
1
88.909
11.821
0.399
0.144
20
HFIYB114D
B
M1
2
1
11.946
0.427
0.144
20
HFIYB2CBD
B
M2
2
2
75.171
11.835
0.403
0.140
20
HFIYB2CCD*
B
M2
2
2
0.130
20
HFIYB2C4D
B
M2
2
2
11.555
0.426
0.144
20
HFIYC11BD
C
M1
3
1
90.400
11.493
0.423
0.148
20
HFIYC11CD
C
M1
3
1
11.639
0.417
0.147
20
HFIYC114D
C
M1
3
1
11.479
0.408
0.148
20
HFIYC21CD
C
M2
3
2
88.788
11.949
0.402
0.146
20
HFIYC214D
C
M2
3
2
94.499
11.953
0.416
0.147
20
HFIYC215D
C
M2
3
2
93.549
11.958
0.389
0.146
20
HFIYA119D
A
M1
1
1
70.041
0.145
20
HFIYA11AD
A
M1
1
1
67.563
0.145
20
HFIYA11BD
A
M1
1
1
76.395
0.146
20
HFIYA11CD
A
M1
1
1
74.707
0.146
20
HFIYA217D
A
M2
1
2
83.165
0.146
20
HFIYA218D
A
M2
1
2
0.146
20
HFIYA219D
A
M2
1
2
68.257
0.145
20
HFIYA21AD
A
M2
1
2
77.754
0.146
20
HFIYB117D
B
M1
2
1
78.394
0.142
20
HFIYB119D
B
M1
2
1
74.240
0.143
20
HFIYB11AD
B
M1
2
1
75.914
0.143
20
HFIYB11BD
B
M1
2
1
85.654
0.144
20
HFIYB2C7D
B
M2
2
2
83.154
0.144
20
HFIYB2C8D
B
M2
2
2
71.529
0.145
20
HFIYB2C9D*
B
M2
2
2
0.146
20
HFIYB2CAD
B
M2
2
2
87.745
0.145
20
HFIYC117D
C
M1
3
1
78.159
0.150
20
HFIYC118D
C
M1
3
1
68.776
0.148
20
HFIYC11AD
C
M1
3
1
72.324
0.148
20
HFIYC217D
C
M2
3
2
72.290
0.145
20
HFIYC218D
C
M2
3
2
78.362
0.145
20
HFIYC21BD
C
M2
3
2
73.619
0.145
20
COMPRESSIVE MODULUS AND POISSON'S RATIO WAS NOT REPORTED FOR SPECIMEN HFIYA21AD.
Modulus of shaded specimens removed due to improper strain gage adhesive used
SPECIMEN HFIYA118D TO HFIYA11CD WERE NOT GAUGED
SPECIMEN HFIYB117C TO HFIYB11AD WERE NOT GAUGED
HFIYB2CAD HAD A BAD STRAIN GAGE
Compressive strengths for HFIYA21XD,HFIYA 117D not reported as un accpetable failure modes were observed
Compressive strengths not reported for HFIYB 114D,HFIYB 2C4D as unacceptable failure modes were observed.
Compressive strength for HFIYC 11CD,HFIYC 114D is not reported as unacceptable failure mode was observed.
*Specimens have thickness taper on edge of specimen
Average 78.794
11.660
0.416
Standard Dev.
7.872
0.243
0.015
Coeff. of Var. [%]
9.991
2.087
3.623
Min. 67.563
11.218
0.389
Max. 94.499
11.958
0.450
Number of Spec.
27
15
15

Page 167 of 238

Failure
Mode
BAT
BAT/HIT
HAT / HIT
ENDCRUSH
ENDCRUSH
DGM / BGM
BGM
HAB / HIB
BAT
BAT
ENDCRUSH
BAT
HIT
HIT
BAB
BAB
BAB
HAB
HAT
HAT
HAB
HGM
HIB
HAT
HAB
BAB
BAB
BAT
BAB
BGM
BGM
BAT
BAT
HAB
HAT
HAB
HAB
HAB
HAT

Average norm
Standard Dev. norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Avg. tply Strengthnorm Modulusnorm


[in]
[ksi]
[Msi]
0.0072
0.0073
0.0073
0.0074
0.0071
0.0072
0.0072
0.0070
0.0072
0.0074
0.0074
0.0074
0.0073
0.0074
0.0073
0.0072
0.0073
0.0073
0.0073
0.0073
0.0073
0.0073
0.0073
0.0071
0.0071
0.0072
0.0072
0.0072
0.0072

77.077
88.899
73.266

92.744

89.877
96.632
94.978
70.479
68.048
77.314
75.883
84.272

11.537
11.791
11.899
11.797
12.095
12.223
12.140

68.881
78.663
77.314
73.647
75.510
85.515
83.125
71.968

0.0073
0.0075
0.0074
0.0074
0.0072
0.0072
0.0073

88.629
81.162
70.639
74.132
72.650
78.707
74.292

0.0073

79.419
8.192
10.315
68.048
96.632
27

0.0070
0.0075
36

11.243
11.498
11.584
11.905
11.547
11.820
11.974
11.535

11.772
0.277
2.352
11.243
12.223
15

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Unnotched Compression Properties (UNC3) -- (ETW)


Normalized Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
2

Prepreg Lot #

Cure Cycle #

0
0

20

40

60

80

100

120

140

160

Laminate Compression Strength (UNC3) [ksi]

Laminate Unnotched Compression Properties (UNC3) -- (ETW)


Normalized Modulus

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
2

0
0.0

2.0

4.0

6.0

8.0

10.0

Laminate Compression Modulus (UNC3) [Msi]

Page 168 of 238

12.0

14.0

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

4.14 Laminate Short Beam Strength Properties


Laminate Short Beam Strength Properties (LSBS) -- (RTD)
Strength
HEXCEL 8552 - IM7 UNI PREPREG
Specimen
Number
HFIqA171A
HFIqA172A
HFIqA173A
HFIqA174A
HFIqA27X1A
HFIqA27X2A
HFIqA27X3A
HFIqB171A
HFIqB172A
HFIqB173A
HFIqB174A
HFIqB271A
HFIqB272A
HFIqB273A
HFIqC17X1A
HFIqC17X2A
HFIqC17X3A
HFIqC271A
HFIqC272A
HFIqC273A
HFIqC274A

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
B
C
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
2
3
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
1
2
2
2
1
1
1
2
2
2
2

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength
[ksi]
11.089
12.055
12.983
12.125
12.646
10.879
12.271
12.748
12.594
11.193
12.687
12.562
12.662
12.269
11.670
12.620
12.560
12.420
9.550
12.318
12.804

Avg. Specimen
Thickn. [in]
0.161
0.174
0.179
0.178
0.176
0.176
0.176
0.172
0.173
0.173
0.173
0.174
0.173
0.172
0.173
0.174
0.174
0.172
0.172
0.172
0.172

12.129
0.831
6.851
9.550
12.983
21

Page 169 of 238

# Plies in
Laminate
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Avg. tply
[in]
0.0067
0.0073
0.0075
0.0074
0.0073
0.0073
0.0073
0.0072
0.0072
0.0072
0.0072
0.0072
0.0072
0.0072
0.0072
0.0073
0.0073
0.0072
0.0072
0.0072
0.0072

0.0072

0.0067
0.0075
21

Failure
Mode
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Short Beam Strength Properties (LSBS) -- (RTD)


Measured Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

0
0

Laminate Short Beam Strength (LSBS) [ksi]

Page 170 of 238

10

12

14

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A


Laminate Short Beam Strength Properties (LSBS) -- (ETW)
Measured Strength
HEXCEL 8552 - IM7 UNI PREPREG
Specimen
Number
HFIqA177D
HFIqA178D
HFIqA17AD
HFIqA27X6D
HFIqA27X7D
HFIqA27X8D
HFIqA27X9D
HFIqB178D
HFIqB179D
HFIqB17AD
HFIqB276D
HFIqB277D
HFIqB278D
HFIqC17X6D
HFIqC17X7D
HFIqC17X8D
HFIqC276D
HFIqC277D
HFIqC278D

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M2
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
2
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength
[ksi]
6.721
6.792
6.993
7.699
7.182
7.240
7.095
7.008
6.885
6.772
6.635
6.846
6.719
6.996
6.922
6.853
7.355
7.060
7.047

Avg. Specimen
Thickn. [in]
0.176
0.176
0.175
0.174
0.174
0.175
0.176
0.173
0.174
0.175
0.173
0.172
0.172
0.174
0.173
0.173
0.173
0.173
0.173

6.991
0.255
3.646
6.635
7.699
19

Page 171 of 238

# Plies in
Laminate
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Avg. tply
[in]
0.0073
0.0073
0.0073
0.0072
0.0073
0.0073
0.0073
0.0072
0.0072
0.0073
0.0072
0.0072
0.0072
0.0072
0.0072
0.0072
0.0072
0.0072
0.0072

0.0072

0.0072
0.0073
19

Failure
Mode
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Short Beam Strength Properties (LSBS) -- (ETW)


Measured Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
2

0
0

Laminate Short Beam Strength (LSBS) [ksi]

Page 172 of 238

10

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

4.15 Lamina Short Beam Strength Properties


Short Beam Strength Properties (SBS) -- (CTD)
Strength
HEXCEL 8552 - IM7 UNI PREPREG
Specimen
Number
HFIQA113B
HFIQA118B
HFIQA11CB
HFIQA11HB
HFIQA214B
HFIQA215B
HFIQA216B
HFIQB11DB
HFIQB11EB
HFIQB11FB
HFIQB217B
HFIQB21DB
HFIQB21GB
HFIQC114B
HFIQC115B
HFIQC116B
HFIQC215B
HFIQC216B
HFIQC21DB

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength
[ksi]
20.889
20.948
20.000
21.120
21.244
21.257
21.148
19.680
21.135
21.188
20.735
21.155
22.130
20.907
20.787
20.868
20.492
21.548
22.577

Avg. Specimen
Thickn. [in]
0.238
0.237
0.239
0.241
0.255
0.258
0.257
0.253
0.257
0.255
0.247
0.248
0.244
0.253
0.259
0.259
0.251
0.250
0.256

21.043
0.642
3.053
19.680
22.577
19

Page 173 of 238

# Plies in
Laminate
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Avg. tply
[in]
0.0070
0.0070
0.0070
0.0071
0.0075
0.0076
0.0075
0.0074
0.0075
0.0075
0.0073
0.0073
0.0072
0.0074
0.0076
0.0076
0.0074
0.0074
0.0075

0.0074

0.0070
0.0076
19

Failure
Mode
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR

CAM-RP-2009-015 April 22, 2011 Revision A

Short Beam Strength Properties (SBS) -- (CTD)


Measured Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

Cure Cycle #

2
1
1

0
0

10

15

Short BeamStrength (SBS) [ksi]

Page 174 of 238

20

25

Prepreg Lot #

3
2

CAM-RP-2009-015 April 22, 2011 Revision A

Short Beam Strength Properties (SBS) -- (RTD)


Strength
HEXCEL 8552 - IM7 UNI PREPREG
Specimen
Number
HFIQA112A
HFIQA119A
HFIQA11BA
HFIQA211A
HFIQA21BA
HFIQA21HA
HFIQB113A
HFIQB117A
HFIQB11BA
HFIQB213A
HFIQB218A
HFIQB21CA
HFIQC112A
HFIQC119A
HFIQC11HA
HFIQC21EA
HFIQC21FA
HFIQC21GA

Hexcel
Batch #
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength
[ksi]
17.128
17.463
16.916
17.780
17.682
17.409
17.649
17.436
17.002
17.233
16.360
16.198
16.861
16.919
17.398
16.984
17.039
16.794

Avg. Specimen
Thickn. [in]
0.224
0.228
0.223
0.225
0.227
0.229
0.231
0.234
0.230
0.243
0.237
0.240
0.225
0.223
0.227
0.261
0.262
0.258

17.125
0.430
2.511
16.198
17.780
18

# Plies in
Laminate
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Avg. tply
[in]
0.0066
0.0067
0.0066
0.0066
0.0067
0.0067
0.0068
0.0069
0.0068
0.0071
0.0070
0.0071
0.0066
0.0066
0.0067
0.0077
0.0077
0.0076

Failure
Mode
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR

0.0069

0.0066
0.0077
18

Short Beam Strength Properties (SBS) -- (RTD)


Measured Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

Prepreg Lot #

Cure Cycle #

3
2

2
1

0
0

10

12

Short Beam Strength (SBS) [ksi]

Page 175 of 238

14

16

18

20

CAM-RP-2009-015 April 22, 2011 Revision A

Short Beam Strength Properties (SBS) -- (ETD)


Strength
HEXCEL 8552 - IM7 UNI PREPREG
Specimen
Number
HFIQA114C
HFIQA117C
HFIQA11DC
HFIQA11GC
HFIQA212C
HFIQA21CC
HFIQA21GC
HFIQB112C
HFIQB118C
HFIQB11IC
HFIQB219C
HFIQB21BC
HFIQB21IC
HFIQC117C
HFIQC11EC
HFIQC11FC
HFIQC214C
HFIQC217C
HFIQC21CC

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
Batch #
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

Strength Avg. Specimen


[ksi]
Thickn. [in]
11.181
0.247
11.775
0.245
11.465
0.248
11.411
0.248
11.125
0.237
11.264
0.237
11.273
0.238
11.293
0.220
11.015
0.224
11.132
0.222
11.201
0.224
10.980
0.228
10.970
0.222
10.989
0.252
11.235
0.248
11.279
0.247
11.576
0.245
11.341
0.245
10.958
0.247

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

11.235
0.218
1.944
10.958
11.775
19

# Plies in
Laminate
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34

Avg. tply
[in]
0.0073
0.0072
0.0073
0.0073
0.0070
0.0070
0.0070
0.0065
0.0066
0.0065
0.0066
0.0067
0.0065
0.0074
0.0073
0.0073
0.0072
0.0072
0.0073

Failure
Mode
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR

Average
0.0070
Standard Dev.
Coeff. of Var. [%]
Min.
0.0065
Max.
0.0074
Number of Spec.
19

Short Beam Strength Properties (SBS) -- (ETD)


Measured Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

0
0

Short Beam Strength (SBS) [ksi]

Page 176 of 238

10

12

14

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

Short Beam Shear Properties (SBS) -- (ETW)


Measured Strength
HEXCEL 8552 - IM7 UNI PREPREG
Specimen
Number
HFIQA115D
HFIQA116D
HFIQA11ED
HFIQA11FD
HFIQA21DD
HFIQA21ED
HFIQA21FD
HFIQB115D
HFIQB116D
HFIQB11CD
HFIQB214D
HFIQB21ED
HFIQB21FD
HFIQC113D
HFIQC118D
HFIQC11DD
HFIQC213D
HFIQC218D
HFIQC21BD

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength Avg. Specimen


[ksi]
Thickn. [in]
8.113
0.251
8.038
0.249
8.169
0.253
8.137
0.252
8.419
0.244
8.151
0.247
8.198
0.246
8.538
0.244
8.395
0.241
8.074
0.244
8.161
0.251
8.151
0.251
8.222
0.250
8.091
0.241
7.863
0.240
8.364
0.242
8.820
0.236
8.748
0.237
8.140
0.236

8.252
0.242
2.927
7.863
8.820
19

# Plies in
Laminate
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34

Avg. tply
[in]
0.0074
0.0073
0.0074
0.0074
0.0072
0.0073
0.0072
0.0072
0.0071
0.0072
0.0074
0.0074
0.0074
0.0071
0.0071
0.0071
0.0069
0.0070
0.0069

Average
0.0072
Standard Dev.
Coeff. of Var. [%]
Min.
0.0069
Max.
0.0074
Number of Spec.
19

Page 177 of 238

COMPRESSION
COMPRESSION
COMPRESSION
COMPRESSION
COMPRESSION
COMPRESSION
COMPRESSION
COMPRESSION
COMPRESSION
COMPRESSION
COMPRESSION
COMPRESSION
COMPRESSION
COMPRESSION
COMPRESSION
COMPRESSION
COMPRESSION
COMPRESSION
COMPRESSION

Failure
Mode
/ INTERLAMINAR SHEAR
/ INTERLAMINAR SHEAR
/ INTERLAMINAR SHEAR
/ INTERLAMINAR SHEAR
/ INTERLAMINAR SHEAR
/ INTERLAMINAR SHEAR
/ INTERLAMINAR SHEAR
/ INTERLAMINAR SHEAR
/ INTERLAMINAR SHEAR
/ INTERLAMINAR SHEAR
/ INTERLAMINAR SHEAR
/ INTERLAMINAR SHEAR
/ INTERLAMINAR SHEAR
/ INTERLAMINAR SHEAR
/ INTERLAMINAR SHEAR
/ INTERLAMINAR SHEAR
/ INTERLAMINAR SHEAR
/ INTERLAMINAR SHEAR
/ INTERLAMINAR SHEAR

CAM-RP-2009-015 April 22, 2011 Revision A

Short Beam Strength Properties (SBS) -- (ETW)


Measured Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

0
0

10

Short Beam Strength (SBS) [ksi]

Page 178 of 238

12

14

16

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

4.16 Open Hole Tension 1 Properties


Laminate Open Hole Tension Properties (OHT1) -- (CTD)
Strength

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFIDA116B
HFIDA117B
HFIDA118B
HFIDA119B
HFIDA216B
HFIDA217B
HFIDA218B
HFIDB115B
HFIDB116B
HFIDB117B
HFIDB216B
HFIDB217B
HFIDB218B
HFIDC116B
HFIDC117B
HFIDC118B
HFIDC216B
HFIDC217B
HFIDC218B

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

Strength
[ksi]
56.265
55.416
57.519
54.997
53.305
55.545
53.271
56.508
55.718
58.780
59.065
58.040
57.482
60.750
61.668
58.242
58.836
59.173
57.662

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Avg. Specimen
Thickn. [in]
0.117
0.118
0.115
0.112
0.117
0.117
0.117
0.116
0.115
0.119
0.115
0.116
0.114
0.116
0.117
0.116
0.117
0.117
0.116

# Plies in
Laminate
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16

Failure
Modes
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM

57.276
2.262
3.950
53.271
61.668
19

Average norm
Standard Dev.norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Avg. tply
[in]
0.0073
0.0074
0.0072
0.0070
0.0073
0.0073
0.0073
0.0073
0.0072
0.0074
0.0072
0.0073
0.0071
0.0073
0.0073
0.0073
0.0073
0.0073
0.0073

Strengthnorm
[ksi]
57.006
56.635
57.344
53.645
54.269
56.598
54.073
57.015
55.549
60.531
58.843
58.544
56.825
61.190
62.524
58.781
59.645
60.089
58.229

0.0073

57.754
2.433
4.213
53.645
62.524
19

0.0070
0.0074
19

Laminate Open Hole Tension Properties (OHT1) -- (CTD)


Normalized Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

Cure Cycle #

2
1
1

0
0

10

20

30

40

50

60

70

Laminate Open Hole Tension Strength [ksi]

Page 179 of 238

80

90

100

Prepreg Lot #

3
2

CAM-RP-2009-015 April 22, 2011 Revision A


Laminate Open Hole Tension Properties (OHT1) -- (RTD)
Strength

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFIDA111A
HFIDA112A
HFIDA113A
HFIDA114A
HFIDA211A
HFIDA212A
HFIDA213A
HFIDB111A
HFIDB112A
HFIDB113A
HFIDB211A
HFIDB212A
HFIDB213A
HFIDC111A
HFIDC112A
HFIDC113A
HFIDC211A
HFIDC212A
HFIDC213A

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

Strength
[ksi]
57.333
57.225
57.430
59.787
53.318
56.126
56.851
58.569
57.566
57.722
59.861
58.439
60.377
59.887
62.217
64.442
58.071
59.987
60.004

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Avg. Specimen
Thickn. [in]
0.112
0.118
0.117
0.117
0.117
0.118
0.118
0.115
0.117
0.116
0.112
0.116
0.114
0.113
0.117
0.116
0.114
0.117
0.116

# Plies in
Laminate
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16

58.695
2.390
4.072
53.318
64.442
19

Failure
Modes
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM

Avg. tply
[in]
0.0070
0.0074
0.0073
0.0073
0.0073
0.0074
0.0074
0.0072
0.0073
0.0072
0.0070
0.0073
0.0071
0.0071
0.0073
0.0072
0.0071
0.0073
0.0073

Average norm 0.00724


Standard Dev.norm
Coeff. of Var. [%]norm
Min. 0.0070
Max. 0.0074
Number of Spec.
19

Strengthnorm
[ksi]
55.956
58.649
58.502
60.825
54.120
57.693
58.068
58.298
58.382
57.922
58.345
58.912
59.915
58.865
63.063
64.610
57.440
61.020
60.481

59.003
2.350
3.982
54.120
64.610
19

Laminate Open Hole Tension Properties (OHT1) -- (RTD)


Normalized Strength
Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

0
0

20

40

60

80

Laminate Open Hole Tension Strength [ksi]

Page 180 of 238

100

120

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Open Hole Tension Properties (OHT1) -- (ETW)


Strength

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFIDA11BD
HFIDA11CD
HFIDA11DD
HFIDA11ED
HFIDA21BD
HFIDA21CD
HFIDA21DD
HFIDB119D
HFIDB11AD
HFIDB11BD
HFIDB21BD
HFIDB21CD
HFIDB21DD
HFIDC11BD
HFIDC11CD
HFIDC11DD
HFIDC11FD
HFIDC21BD
HFIDC21CD
HFIDC21DD

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
1
2
2
2

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength
[ksi]
63.475
62.272
62.206
63.863
66.003
67.056
67.795
63.402
65.212
71.042
73.233
67.200
67.239
65.357
69.942
68.968
65.533
67.346
65.625
66.795

Avg. Specimen
Thickn. [in]
0.116
0.116
0.117
0.116
0.117
0.117
0.118
0.113
0.116
0.116
0.114
0.115
0.115
0.116
0.116
0.116
0.117
0.117
0.117
0.116

# Plies in
Laminate
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16

66.478
2.853
4.292
62.206
73.233
20

Failure
Modes
AGM
AGM
AGM
AGM
AGM
MGM
AGM
AGM
AGM
MGM
AGM
AGM
AGM
AGM
AGM
AGM
MGM
AGM
AGM
AGM

Average norm
Standard Dev. norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Laminate Open Hole Tension Properties (OHT1) -- (ETW)


Normalized Strength

Avg. tply
[in]
0.0073
0.0073
0.0073
0.0072
0.0073
0.0073
0.0074
0.0071
0.0072
0.0072
0.0071
0.0072
0.0072
0.0072
0.0073
0.0072
0.0073
0.0073
0.0073
0.0073

Strengthnorm
[ksi]
64.017
62.966
62.926
64.297
67.092
68.288
69.218
62.154
65.656
71.515
72.587
67.152
67.141
65.716
70.579
69.297
66.472
68.184
66.660
67.413

0.0073

66.966
2.850
4.255
62.154
72.587
20

0.0071
0.0074

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
1
1

0
0

20

40

60

80

Laminate Open Hole Tension Strength [ksi]

Page 181 of 238

100

120

Prepreg Lot #

Cure Cycle #

3
2

CAM-RP-2009-015 April 22, 2011 Revision A

4.17 Open Hole Tension 2 Properties


Laminate Open Hole Tension Properties (OHT2) -- (CTD)
Strength

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFIEA115B
HFIEA116B
HFIEA117B
HFIEA118B
HFIEA215B
HFIEA216B
HFIEA217B
HFIEB115B
HFIEB116B
HFIEB117B
HFIEB215B
HFIEB216B
HFIEB217B
HFIEC115B
HFIEC116B
HFIEC117B
HFIEC215B
HFIEC216B
HFIEC217B

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength
[ksi]
44.404
45.649
44.586
45.233
43.883
44.158
44.366
45.728
46.353
45.119
46.586
46.601
46.631
45.492
46.661
47.025
46.563
46.288
45.652

Avg. Specimen
Thickn. [in]
0.145
0.146
0.146
0.146
0.147
0.146
0.149
0.144
0.144
0.145
0.144
0.143
0.144
0.139
0.146
0.144
0.145
0.145
0.147

# Plies in
Laminate
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20

45.630
0.987
2.164
43.883
47.025
19

Failure
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM

Avg. tply
[in]
0.0072
0.0073
0.0073
0.0073
0.0074
0.0073
0.0074
0.0072
0.0072
0.0072
0.0072
0.0072
0.0072
0.0070
0.0073
0.0072
0.0073
0.0072
0.0073

Strengthnorm
[ksi]
44.686
46.209
45.262
45.940
44.940
44.920
45.768
45.664
46.224
45.422
46.586
46.347
46.734
44.045
47.196
47.063
46.962
46.535
46.524

0.0073

45.949
0.881
1.918
44.045
47.196
19

Average norm
Standard Dev.norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

0.0070
0.0074
19

Laminate Open Hole Tension Properties (OHT2) -- (CTD)


Normalized Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
1
1

0
0

10

20

30

40

50

Laminate Open Hole Tension Strength [ksi]

Page 182 of 238

60

70

80

Prepreg Lot #

Cure Cycle #

3
2

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Open Hole Tension Properties (OHT2) -- (RTD)


Strength

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFIEA111A
HFIEA112A
HFIEA113A
HFIEA114A
HFIEA211A
HFIEA212A
HFIEA213A
HFIEB111A
HFIEB112A
HFIEB113A
HFIEB211A
HFIEB212A
HFIEB213A
HFIEC111A
HFIEC112A
HFIEC113A
HFIEC211A
HFIEC212A
HFIEC213A

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2
Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength
[ksi]
44.383
43.792
43.592
43.843
41.048
42.213
42.685
42.668
43.774
43.345
45.471
45.720
45.864
42.805
42.882
43.976
43.083
44.403
43.720

Avg. Specimen
Thickn. [in]
0.142
0.147
0.145
0.145
0.140
0.149
0.147
0.144
0.145
0.144
0.140
0.145
0.143
0.140
0.145
0.143
0.140
0.147
0.145

# Plies in
Laminate
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20

43.646
1.207
2.766
41.048
45.864
19

Failure
Modes
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
Average norm
Standard Dev.norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Laminate Open Hole Tension Properties (OHT2) -- (RTD)


Normalized Strength

Avg. tply
[in]
0.0071
0.0073
0.0073
0.0073
0.0070
0.0074
0.0073
0.0072
0.0072
0.0072
0.0070
0.0072
0.0072
0.0070
0.0072
0.0072
0.0070
0.0074
0.0072

Strengthnorm
[ksi]
43.915
44.583
44.006
44.218
39.912
43.571
43.490
42.589
44.068
43.240
44.286
45.958
45.598
41.705
43.071
43.798
41.916
45.472
44.009

0.0072

43.653
1.433
3.284
39.912
45.958
19

0.0070
0.0074
19

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

0
0

10

20

30

40

50

Laminate Open Hole Tension Strength [ksi]

Page 183 of 238

60

70

80

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

normalizing tply
[in]
0.0072

Laminate Open Hole Tension Properties (OHT2) -- (ETW)


Strength
HEXCEL 8552 - IM7 UNI PREPREG
Specimen
Number
HFIEA11AD
HFIEA11BD
HFIEA11CD
HFIEA219DD
HFIEA21AD
HFIEA21BD
HFIEB119D
HFIEB11AD
HFIEB11BD
HFIEB218D
HFIEB219D
HFIEB21AD
HFIEC118D
HFIEC119D
HFIEC11AD
HFIEC218D
HFIEC219D
HFIEC21AD

Hexcel
Batch #
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength
[ksi]
38.273
37.898
38.398
36.182
36.377
36.605
38.837
39.577
39.010
37.223
38.589
40.019
39.249
38.575
38.907
39.152
37.182
40.037

Avg. Specimen
Thickn. [in]
0.145
0.146
0.146
0.146
0.148
0.146
0.140
0.145
0.143
0.143
0.145
0.143
0.143
0.144
0.144
0.143
0.140
0.146

# Plies in
Laminate
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20

Failure
Modes
AGM
AGM
AGM
AGM
AGM
AGM
AGM
LGM
LGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM

38.338
1.192
3.110
36.182
40.037
18

Average norm
Standard Dev.norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Avg. tply
[in]
0.0072
0.0073
0.0073
0.0073
0.0074
0.0073
0.0070
0.0072
0.0072
0.0071
0.0072
0.0072
0.0072
0.0072
0.0072
0.0071
0.0070
0.0073

Strengthnorm
[ksi]
38.499
38.451
38.891
36.773
37.316
37.020
37.691
39.810
38.789
36.861
38.825
39.875
39.095
38.445
38.853
38.771
36.270
40.709

0.0072

38.386
1.189
3.098
36.270
40.709
18

0.0070
0.0074
18

Laminate Open Hole Tension Properties (OHT2) -- (ETW)


Normalized Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
1
1

0
0

10

20

30

40

50

Laminate Open Hole Tension Strength [ksi]

Page 184 of 238

60

70

80

Prepreg Lot #

Cure Cycle #

3
2

CAM-RP-2009-015 April 22, 2011 Revision A

4.18 Open Hole Tension 3 Properties


Laminate Open Hole Tension Properties (OHT3) -- (CTD)
Strength

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFIFA116B
HFIFA117B
HFIFA118B
HFIFA119B
HFIFA215B
HFIFA216B
HFIFA217B
HFIFB115B
HFIFB116B
HFIFB117B
HFIFB214B
HFIFB215B
HFIFB216B
HFIFC115B
HFIFC116B
HFIFC117B
HFIFC215B
HFIFC216B
HFIFC217B

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength
[ksi]
72.748
71.330
74.260
75.999
70.749
74.477
70.910
84.181
80.126
80.709
82.090
83.543
84.377
82.716
83.049
78.341
76.176
77.746
77.844

Avg. Specimen
Thickn. [in]
0.147
0.148
0.149
0.148
0.147
0.148
0.149
0.144
0.144
0.144
0.146
0.145
0.144
0.143
0.144
0.145
0.143
0.144
0.144

# Plies in
Laminate
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20

77.967
4.683
6.006
70.749
84.377
19

Failure
Mode
AGM / LGM
AGM / LGM
AGM / LGM
AGM / LGM
AGM / LGM
AGM / LGM
AGM / LGM
LGM / AGM
AGM
LGM / AGM
LGM / AGM
LGM / AGM
AGM
LGM/AGM
LGM
AGM
AGM/LGM
AGM
LGM

Average norm
Standard Dev. norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Avg. tply
[in]
0.0074
0.0074
0.0075
0.0074
0.0074
0.0074
0.0075
0.0072
0.0072
0.0072
0.0073
0.0073
0.0072
0.0072
0.0072
0.0072
0.0072
0.0072
0.0072

Strengthnorm
[ksi]
74.264
73.476
76.839
77.935
72.412
76.537
73.389
84.288
79.894
80.868
82.945
84.269
84.279
82.362
82.828
78.731
75.664
77.566
77.727

0.0073

78.751
3.964
5.033
72.412
84.288
19

0.0072
0.0075
19

Laminate Open Hole Tension Properties (OHT3) -- (CTD)


Normalized Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
1
1

0
0

20

40

60

80

100

Laminate Open Hole Tension Strength [ksi]

Page 185 of 238

120

140

160

Prepreg Lot #

Cure Cycle #

3
2

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Open Hole Tension Properties (OHT3) -- (RTD)


Strength

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFIFA111A
HFIFA112A
HFIFA113A
HFIFA114A
HFIFA211A
HFIFA212A
HFIFA213A
HFIFB111A
HFIFB112A
HFIFB113A
HFIFB211A
HFIFB212A
HFIFB213A
HFIFC111A
HFIFC112A
HFIFC113A
HFIFC211A
HFIFC212A
HFIFC213A

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength
[ksi]
81.536
81.570
84.147
83.870
80.490
79.778
79.068
89.781
88.390
88.177
89.962
93.126
85.187
89.951
94.489
94.135
83.280
87.504
91.470

Avg. Specimen
Thickn. [in]
0.145
0.149
0.148
0.148
0.141
0.149
0.147
0.133
0.147
0.143
0.141
0.145
0.145
0.138
0.145
0.143
0.140
0.145
0.144

# Plies in
Laminate
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20

86.627
4.958
5.724
79.068
94.489
19

Failure
Mode
LGM/AGM
LGM
LGM
LGM/AGM
LGM/AGM
LGM
LGM
AGM
AGM
AGM / LGM
AGM / LGM
AGM / LGM
AGM
LGM / AGM
LGM / AGM
LGM / AGM
LGM / AGM
LGM / AGM
LGM / AGM

Average norm
Standard Dev.norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Laminate Open Hole Tension Properties (OHT3) -- (RTD)


Normalized Strength

Avg. tply
[in]
0.0073
0.0074
0.0074
0.0074
0.0071
0.0074
0.0074
0.0066
0.0073
0.0072
0.0071
0.0073
0.0072
0.0069
0.0073
0.0072
0.0070
0.0073
0.0072

Strengthnorm
[ksi]
82.103
84.213
86.484
86.200
78.897
82.475
80.880
82.735
89.976
87.595
88.328
93.859
85.768
85.953
95.167
93.536
80.977
88.324
91.746

0.0072

86.590
4.725
5.457
78.897
95.167
19

0.0066
0.0074
19

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
1
1

0
0

20

40

60

80

100

Laminate Open Hole Tension Strength [ksi]

Page 186 of 238

120

140

160

Prepreg Lot #

Cure Cycle #

3
2

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Open Hole Tension Properties (OHT3) -- (ETW)


Strength

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFIFA11BD*
HFIFA11CD*
HFIFA11DD*
HFIFA11ED*
HFIFA219D
HFIFA21AD
HFIFA21BD
HFIFB118D
HFIFB119D*
HFIFB11AD
HFIFB11BD
HFIFB218D
HFIFB219D
HFIFB21AD
HFIFC119D
HFIFC11AD
HFIFC11BD
HFIFC219D
HFIFC21AD
HFIFC21BD

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
1
2
2
2
1
1
1
2
2
2

Strength
[ksi]
114.518
107.381
114.736
103.774
102.238
110.569
106.810
128.781
117.340
106.610
114.723
125.681
119.126
121.801
116.543
115.517
117.042
119.003
104.988
110.152

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Avg. Specimen
Thickn. [in]
0.147
0.147
0.147
0.149
0.148
0.148
0.147
0.145
0.137
0.147
0.144
0.145
0.146
0.147
0.144
0.145
0.143
0.143
0.144
0.144

# Plies in
Laminate
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20

113.867
7.248
6.365
102.238
128.781
20

Failure
Mode
LGM
LGM
LGM
LGM
LGM
LGM
LGM
AGM
LGM/AGM
LGM/AGM
LGM/AGM
LGM/AGM
LGM/AGM
LGM/AGM
AGM
LGM
AGM/LGM
AGM
AGM/LGM
AGM
Average norm
Standard Dev.norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Avg. tply
[in]
0.0074
0.0073
0.0074
0.0075
0.0074
0.0074
0.0074
0.0073
0.0068
0.0073
0.0072
0.0072
0.0073
0.0073
0.0072
0.0072
0.0071
0.0072
0.0072
0.0072

Strengthnorm
[ksi]
116.903
109.370
117.126
107.377
105.042
113.948
109.146
129.750
111.486
108.732
114.935
126.278
120.726
124.141
116.435
116.266
116.188
118.397
105.036
109.935

0.0073

114.861
6.830
5.946
105.036
129.750
20

0.0068
0.0075
20

Laminate Open Hole Tension Properties (OHT3) -- (ETW)


Normalized Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

Prepreg Lot #

Cure Cycle #

1
1

0
0

20

40

60

80

100

120

140

Laminate Open Hole Tension Properties Strength [ksi]

Page 187 of 238

160

180

200

CAM-RP-2009-015 April 22, 2011 Revision A

4.19 Filled-Hole Tension 1 Properties


Laminate Filled-Hole Tension Properties (FHT1) -- (CTD)
Strength

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFI4A117B
HFI4A118B
HFI4A119B
HFI4A11AB
HFI4A215B
HFI4A216B
HFI4A217B
HFI4B115B
HFI4B116B
HFI4B117B
HFI4B215B
HFI4B216B
HFI4B217B
HFI4C115B
HFI4C116B
HFI4C117B
HFI4C215B
HFI4C216B
HFI4C217B

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

Strength
[ksi]
59.027
57.302
60.172
61.327
62.748
60.030
59.748
65.873
67.053
64.288
65.191
64.500
66.214
65.035
65.600
66.666
62.871
65.150
68.013

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Avg. Specimen
Thickn. [in]
0.117
0.117
0.118
0.117
0.117
0.117
0.118
0.114
0.114
0.115
0.115
0.114
0.115
0.117
0.118
0.115
0.116
0.116
0.118

# Plies in
Laminate
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16

Failure
Mode
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM

63.516
3.085
4.856
57.302
68.013
19

Average norm
Standard Dev. norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Avg. tply
[in]
0.0073
0.0073
0.0074
0.0073
0.0073
0.0073
0.0074
0.0071
0.0071
0.0072
0.0072
0.0071
0.0072
0.0073
0.0074
0.0072
0.0073
0.0073
0.0073

Strengthnorm
[ksi]
60.095
57.998
61.469
62.436
63.891
61.046
61.002
65.244
66.151
63.953
64.955
63.968
66.185
65.853
67.384
66.328
63.417
65.630
69.401

0.0073

64.021
2.810
4.390
57.998
69.401
19

0.0071
0.0074
19

Laminate Filled-Hole Tension Properties (FHT1) -- (CTD)


Normalized Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
1
1

0
0

10

20

30

40

50

60

Laminate Filled-Hole Tension Strength [ksi]

Page 188 of 238

70

80

90

100

Prepreg Lot #

Cure Cycle #

3
2

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Filled-Hole Tension Properties (FHT1) -- (RTD)


Strength

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFI4A112A
HFI4A113A
HFI4A114A
HFI4A115A
HFI4A211A
HFI4A212A
HFI4A214A
HFI4B111A
HFI4B112A
HFI4B113A
HFI4B211A
HFI4B212A
HFI4B214A
HFI4C111A
HFI4C113A*
HFI4C114A*
HFI4C211A
HFI4C212A
HFI4C213A

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

Strength
[ksi]
64.899
60.163
59.596
63.146
60.980
64.939
64.451
70.013
66.645
67.424
69.067
66.498
72.193
67.382
71.250
68.599
67.144
62.523
66.195

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Avg. Specimen
Thickn. [in]
0.117
0.117
0.118
0.118
0.112
0.118
0.117
0.110
0.116
0.114
0.110
0.116
0.115
0.111
0.117
0.117
0.111
0.118
0.116

# Plies in
Laminate
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16

Failure
Mode
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM

65.953
3.569
5.412
59.596
72.193
19

Average norm
Standard Dev. norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Avg. tply
[in]
0.0073
0.0073
0.0074
0.0073
0.0070
0.0074
0.0073
0.0068
0.0072
0.0071
0.0069
0.0072
0.0072
0.0069
0.0073
0.0073
0.0069
0.0074
0.0073

Strengthnorm
[ksi]
66.120
61.190
61.165
64.444
59.198
66.433
65.561
66.579
66.982
66.644
66.030
66.863
71.764
64.740
72.343
69.591
64.667
64.287
66.885

0.0072

65.868
3.259
4.948
59.198
72.343
19

0.0068
0.0074
19

Laminate Filled-Hole Tension Properties (FHT1) -- (RTD)


Normalized Strength
Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

0
0

10

20

30

40

50

60

70

Laminate Filled-Hole Tension Strength [ksi]

Page 189 of 238

80

90

100

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Filled-Hole Tension Properties (FHT1) -- (ETW)


Strength

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFI4A11BD
HFI4A11CD
HFI4A11DD
HFI4A11FD
HFI4A218D
HFI4A21AD
HFI4A21BD
HFI4A21CD
HFI4B118D
HFI4B11AD
HFI4B11BD
HFI4B218D
HFI4B21BD
HFI4B21CD
HFI4C118D
HFI4C11AD
HFI4C11BD
HFI4C11CD
HFI4C21AD
HFI4C21BD
HFI4C21CD
HFI4C21DD

Hexcel
Batch #
A
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M1
M2
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
2
1
1
1
2
2
2
1
1
1
1
2
2
2
2

Strength
[ksi]
67.367
66.790
67.424
64.289
69.017
67.726
69.612
67.440
69.282
68.161
73.843
74.583
72.453
72.070
71.303
65.293
72.470
70.193
67.537
71.258
71.493
69.776

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Avg. Specimen
Thickn. [in]
0.118
0.117
0.117
0.117
0.117
0.117
0.117
0.116
0.115
0.116
0.114
0.115
0.115
0.115
0.117
0.120
0.117
0.118
0.118
0.116
0.117
0.117

# Plies in
Laminate
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16

Failure
Mode
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM

69.517
2.709
3.897
64.289
74.583
22

Average norm
Standard Dev.norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Avg. tply
[in]
0.0074
0.0073
0.0073
0.0073
0.0073
0.0073
0.0073
0.0073
0.0072
0.0072
0.0071
0.0072
0.0072
0.0072
0.0073
0.0075
0.0073
0.0073
0.0074
0.0073
0.0073
0.0073

Strengthnorm
[ksi]
68.770
67.959
68.429
65.172
69.945
68.911
70.418
67.958
69.362
68.526
72.914
74.400
72.316
71.882
72.211
67.910
73.309
71.604
69.149
71.939
72.600
70.634

0.0073

70.287
2.278
3.240
65.172
74.400
22

0.0071
0.0075
22

Laminate Filled-Hole Tension Properties (FHT1) -- (ETW)


Normalized Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

Cure Cycle #

2
1
1

0
0

10

20

30

40

50

60

Laminate Filled-Hole Tension Strength [ksi]

Page 190 of 238

70

80

90

100

Prepreg Lot #

3
2

CAM-RP-2009-015 April 22, 2011 Revision A

4.20 Filled-Hole Tension 2 Properties


Laminate Filled-Hole Tension Properties (FHT2) -- (CTD)
Strength

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFI5A115B
HFI5A116B
HFI5A117B
HFI5A118B
HFI5A215B
HFI5A216B
HFI5A217B
HFI5B183B
HFI5B184B
HFI5B185B
HFI5B215B
HFI5B216B
HFI5B219B
HFI5C116B
HFI5C117B
HFI5C118B
HFI5C216B
HFI5C217B
HFI5C218B

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
Batch #
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength
[ksi]
51.005
51.396
50.245
51.243
51.790
51.627
52.243
54.728
53.591
51.798
53.233
53.008
50.393
53.211
53.345
50.679
50.227
53.565
51.544

Avg. Specimen
Thickn. [in]
0.146
0.146
0.148
0.141
0.148
0.147
0.148
0.144
0.144
0.144
0.145
0.144
0.145
0.144
0.145
0.138
0.144
0.144
0.141

# Plies in
Laminate
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20

52.046
1.316
2.528
50.227
54.728
19

Failure
Mode
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM

Avg. tply
[in]
0.0073
0.0073
0.0074
0.0071
0.0074
0.0073
0.0074
0.0072
0.0072
0.0072
0.0072
0.0072
0.0073
0.0072
0.0073
0.0069
0.0072
0.0072
0.0071

Strengthnorm
[ksi]
51.749
52.038
51.693
50.306
53.127
52.661
53.809
54.640
53.697
51.822
53.424
53.106
50.877
53.026
53.876
48.544
50.378
53.386
50.613

0.0072

52.251
1.567
2.999
48.544
54.640
19

Average norm
Standard Dev.norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

0.0069
0.0074
19

Laminate Filled-Hole Tension Properties (FHT2) -- (CTD)


Normalized Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

Cure Cycle #

2
1
1

0
0

10

20

30

40

50

Laminate Filled-Hole Tension Strength [ksi]

Page 191 of 238

60

70

80

Prepreg Lot #

3
2

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Filled-Hole Tension Properties (FHT2) -- (RTD)


Strength

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFI5A111A
HFI5A112A
HFI5A113A
HFI5A114A
HFI5A211A
HFI5A212A
HFI5A213A
HFI5B181A
HFI5B121A
HFI5B182A
HFI5B211A
HFI5B212A
HFI5B213A
HFI5C111A
HFI5C112A
HFI5C113A
HFI5C211A
HFI5C213A
HFI5C214A

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength
[ksi]
45.997
47.027
50.242
49.553
49.823
49.363
47.248
48.549
48.010
48.932
46.169
50.056
44.673
49.493
48.053
47.632
48.980
48.012
45.723

Avg. Specimen
Thickn. [in]
0.140
0.148
0.145
0.146
0.145
0.147
0.147
0.142
0.143
0.144
0.142
0.146
0.144
0.140
0.147
0.143
0.142
0.144
0.144

# Plies in
Laminate
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20

48.081
1.605
3.337
44.673
50.242
19

Failure
Mode
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM
AGM

Average norm
Standard Dev. norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Avg. tply
[in]
0.0070
0.0074
0.0073
0.0073
0.0072
0.0074
0.0074
0.0071
0.0072
0.0072
0.0071
0.0073
0.0072
0.0070
0.0074
0.0072
0.0071
0.0072
0.0072

Strengthnorm
[ksi]
44.587
48.268
50.679
50.264
50.036
50.546
48.244
47.723
47.726
49.068
45.437
50.786
44.637
48.084
49.087
47.411
48.350
48.173
45.781

0.0072

48.152
1.941
4.031
44.587
50.786
19

0.0070
0.0074
19

Laminate Filled-Hole Tension Properties (FHT2) -- (RTD)


Normalized Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

0
0

10

20

30

40

50

Laminate Filled-Hole Tension Strength [ksi]

Page 192 of 238

60

70

80

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A


Laminate Filled-Hole Tension Properties (FHT2) -- (ETW)
Strength

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFI5A11AD
HFI5A11BD
HFI5A11DD
HFI5A11ED
HFI5A21AD
HFI5A21CD
HFI5A21DD
HFI5B186D
HFI5B122D
HFI5B187D
HFI5B21CD
HFI5B21DD
HFI5B21ED
HFI5C11BD
HFI5C11CD
HFI5C11DD
HFI5C21BD
HFI5C21CD
HFI5C21ED

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength
[ksi]
40.752
41.247
42.864
42.513
41.976
40.962
41.571
42.962
41.756
42.322
42.137
43.421
42.356
43.106
41.453
42.816
42.810
43.152
43.538

Avg. Specimen
Thickn. [in]
0.146
0.145
0.147
0.148
0.147
0.148
0.147
0.144
0.144
0.144
0.144
0.144
0.146
0.144
0.145
0.145
0.145
0.143
0.143

# Plies in
Laminate
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20

42.301
0.832
1.967
40.752
43.538
19

Failure
Mode
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM

Average norm
Standard Dev.norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Laminate Filled-Hole Tension Properties (FHT2) -- (ETW)


Normalized Strength

Avg. tply
[in]
0.0073
0.0073
0.0073
0.0074
0.0074
0.0074
0.0074
0.0072
0.0072
0.0072
0.0072
0.0072
0.0073
0.0072
0.0072
0.0072
0.0072
0.0072
0.0072

Strengthnorm
[ksi]
41.219
41.572
43.643
43.753
42.885
41.986
42.509
42.898
41.621
42.400
42.264
43.451
42.842
43.002
41.683
42.974
43.067
42.982
43.307

0.0073

42.635
0.738
1.732
41.219
43.753
19

0.0072
0.0074
19

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

0
0

10

20

30

40

50

Laminate Filled-Hole Tension Strength [ksi]

Page 193 of 238

60

70

80

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

4.21 Filled-Hole Tension 3 Properties


normalizing tply
[in]
0.0072

Laminate Filled-Hole Tension Properties (FHT3) -- (CTD)


Strength
HEXCEL 8552 - IM7 UNI PREPREG
Specimen
Number
HFI6A111B
HFI6A112B*
HFI6A113B
HFI6A114B
HFI6A212B
HFI6A213B
HFI6A214B
HFI6B112B
HFI6B113B
HFI6B115B
HFI6B216B
HFI6B217B
HFI6B219B*
HFI6C116B*
HFI6C117B
HFI6C118B
HFI6C216B
HFI6C217B
HFI6C218B

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength
[ksi]
76.916
77.654
79.761
71.758
71.220
72.885
79.149
83.462
85.087
83.583
84.691
79.312
86.562
88.226
83.733
80.774
85.168
82.027
78.179

Avg. Specimen
Thickn. [in]
0.148
0.147
0.148
0.141
0.148
0.147
0.147
0.145
0.144
0.143
0.142
0.145
0.139
0.144
0.145
0.140
0.144
0.144
0.140

# Plies in
Laminate
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20

Failure
Mode
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
AGM
AGM
AGM
AGM
LGM
LGM
AGM
AGM
LGM
LGM

80.534
4.936
6.129
71.220
88.226
19

Average norm
Standard Dev.norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Laminate Filled-Hole Tension Properties (FHT3) -- (CTD)


Normalized Strength

Avg. tply
[in]
0.0074
0.0074
0.0074
0.0070
0.0074
0.0073
0.0073
0.0072
0.0072
0.0072
0.0071
0.0073
0.0070
0.0072
0.0073
0.0070
0.0072
0.0072
0.0070

Strengthnorm
[ksi]
79.230
79.271
82.013
70.247
73.339
74.260
80.670
83.877
84.811
83.109
83.799
79.899
83.777
88.154
84.595
78.726
85.119
82.245
76.252

0.0072

80.705
4.593
5.691
70.247
88.154
19

0.0070
0.0074
19

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

Cure Cycle #

1
1

0
0

20

40

60

80

100

Laminate Filled-Hole Tension Strength [ksi]

Page 194 of 238

120

140

Prepreg Lot #

3
2

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Filled-Hole Tension Properties (FHT3) -- (RTD)


Strength

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFI6A115A
HFI6A116A
HFI6A117A
HFI6A118A
HFI6A215A
HFI6A216A
HFI6A218A
HFI6B116A
HFI6B117A
HFI6B118A
HFI6B212A
HFI6B213A
HFI6B215A
HFI6C112A
HFI6C113A1
HFI6C114A
HFI6C211A
HFI6C212A
HFI6C215A

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength
[ksi]
84.133
82.476
77.075
84.415
87.203
87.870
89.304
99.567
96.382
101.085
91.092
89.175
102.608
96.557
100.427
101.732
90.816
91.339
93.490

Avg. Specimen
Thickn. [in]
0.147
0.147
0.148
0.143
0.147
0.148
0.144
0.143
0.144
0.140
0.145
0.143
0.143
0.145
0.143
0.144
0.136
0.145
0.144

# Plies in
Laminate
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20

Failure
Mode
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM

91.934
7.269
7.906
77.075
102.608
19

Average norm
Standard Dev.norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Avg. tply
[in]
0.0073
0.0073
0.0074
0.0072
0.0074
0.0074
0.0072
0.0071
0.0072
0.0070
0.0072
0.0071
0.0072
0.0073
0.0072
0.0072
0.0068
0.0072
0.0072

Strengthnorm
[ksi]
85.876
83.956
79.154
83.887
89.212
90.077
89.169
98.714
96.694
98.066
91.419
88.514
102.156
97.238
100.020
101.391
86.065
91.900
93.588

0.0072

91.952
6.624
7.204
79.154
102.156
19

0.0068
0.0074
19

Laminate Filled-Hole Tension Properties (FHT3) -- (RTD)


Normalized Strength
Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2

1
1

0
0

20

40

60

80

Laminate Filled-Hole Tension Strength [ksi]

Page 195 of 238

100

120

140

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Filled-Hole Tension Properties (FHT3) -- (ETW)


Strength

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFI6A21AD
HFI6A21BD
HFI6A21ED
HFI6A119D*
HFI6A11AD
HFI6A11BD
HFI6A11CD
HFI6B11BD
HFI6B11CD
HFI6B11ED
HFI6B21BD
HFI6B21CD
HFI6B21DD
HFI6C11AD**
HFI6C11CD
HFI6C11FD
HFI6C21BD
HFI6C21CD
HFI6C21DD

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M2
M2
M2
M1
M1
M1
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
2
2
2
1
1
1
1
1
1
1
2
2
2
1
1
1
2
2
2

Strength
[ksi]
101.196
102.134
101.429
96.211
97.394
92.014
99.674
102.156
96.596
106.183
99.756
97.666
105.477
100.274
105.904
107.293
100.091
100.494
102.630

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Avg. Specimen
Thickn. [in]
0.149
0.147
0.148
0.141
0.149
0.147
0.147
0.143
0.143
0.142
0.143
0.143
0.143
0.144
0.144
0.145
0.144
0.143
0.144

# Plies in
Laminate
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20

Failure
Mode
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM
MGM

100.767
3.852
3.823
92.014
107.293
19

Average norm
Standard Dev. norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Avg. tply
[in]
0.0074
0.0074
0.0074
0.0071
0.0074
0.0073
0.0073
0.0072
0.0072
0.0071
0.0071
0.0072
0.0072
0.0072
0.0072
0.0073
0.0072
0.0072
0.0072

Strengthnorm
[ksi]
104.558
104.521
104.152
94.263
100.506
93.921
101.635
101.719
96.239
104.917
98.936
97.146
104.818
100.518
105.916
108.112
99.743
100.041
102.309

0.0072

101.262
3.953
3.904
93.921
108.112
19

0.0071
0.0074
19

Laminate Filled-Hole Tension Properties (FHT3) -- (ETW)


Normalized Strength
HEXCEL 8552 - IM7 UNI PREPREG

Cure Cycle #
Prepreg Lot #

2
2

1
1

0
0

20

40

60

80

Laminate Filled-Hole Tension Strength [ksi]

Page 196 of 238

100

120

140

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

4.22 Open Hole Compression 1 Properties


Laminate Open Hole Compression Properties (OHC1) -- (RTD)
Strength

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFIGA111A
HFIGA112A
HFIGA113A
HFIGA114A
HFIGA211A
HFIGA212A
HFIGA213A
HFIGB111A
HFIGB112A
HFIGB113A
HFIGB211A
HFIGB212A
HFIGB213A
HFIGC111A
HFIGC112A
HFIGC113A
HFIGC211A
HFIGC212A
HFIGC213A

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2
Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength
[ksi]
49.352
48.708
49.494
49.152
47.573
46.871
49.658
51.283
47.434
48.741
49.322
49.005
49.499
50.305
51.152
49.517
45.150
48.727
48.053

Avg. Specimen
Thickn. [in]
0.174
0.181
0.178
0.178
0.168
0.181
0.176
0.165
0.174
0.172
0.166
0.175
0.174
0.170
0.172
0.173
0.168
0.177
0.174

# Plies in
Laminate
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24

48.894
1.448
2.962
45.150
51.283
19

Failure
Modes
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
Average norm
Standard Dev. norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Avg. tply
[in]
0.0072
0.0075
0.0074
0.0074
0.0070
0.0075
0.0073
0.0069
0.0072
0.0072
0.0069
0.0073
0.0072
0.0071
0.0072
0.0072
0.0070
0.0074
0.0072

Strengthnorm
[ksi]
49.676
50.991
50.993
50.731
46.316
49.145
50.592
49.096
47.717
48.624
47.400
49.756
49.719
49.393
50.974
49.455
43.909
49.831
48.266

0.0072

49.083
1.793
3.653
43.909
50.993
19

0.0069
0.0075

Laminate Open Hole Compression Properties (OHC1) -- (RTD)


Normalized Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

0
0

10

20

30

40

50

60

Laminate Open Hole Compression Strength [ksi]

Page 197 of 238

70

80

90

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Open Hole Compression Properties (OHC1) -- (ETW)


Strength

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFIGA117D
HFIGA118D
HFIGA119D
HFIGA11AD
HFIGA216D
HFIGA217D
HFIGA218D
HFIGB116D
HFIGB117D
HFIGB118D
HFIGB216D
HFIGB217D
HFIGB218D
HFIGC116D
HFIGC117D
HFIGC118D
HFIGC216D
HFIGC217D
HFIGC218D

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2
Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength
[ksi]
37.501
36.396
36.163
35.770
35.276
35.697
33.586
34.888
35.442
34.874
36.226
33.749
36.958
34.153
33.898
34.086
36.149
34.019
35.613

Avg. Specimen
Thickn. [in]
0.180
0.172
0.179
0.176
0.177
0.179
0.173
0.172
0.174
0.169
0.173
0.176
0.169
0.173
0.176
0.168
0.173
0.177
0.171

# Plies in
Laminate
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24

Failure
Modes
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM

35.287
1.148
3.252
33.586
37.501
19

Avg. tply
[in]
0.0075
0.0072
0.0075
0.0073
0.0074
0.0074
0.0072
0.0072
0.0073
0.0070
0.0072
0.0073
0.0070
0.0072
0.0073
0.0070
0.0072
0.0074
0.0071

Strengthnorm
[ksi]
38.956
36.203
37.426
36.436
36.102
36.933
33.628
34.781
35.757
34.144
36.163
34.329
36.049
34.110
34.457
33.080
36.278
34.764
35.190

0.0072

35.515
1.445
4.069
33.080
38.956
19

Average norm
Standard Dev.norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

0.0070
0.0075

Laminate Open Hole Compression Properties (OHC1) -- (ETW)


Normalized Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

0
0

10

15

20

25

30

Laminate Open Hole Compression Strength [ksi]

Page 198 of 238

35

40

45

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

4.23 Open Hole Compression 2 Properties


Laminate Open Hole Compression Properties (OHC2) -- (RTD)
Strength

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Hexcel
Hexcel Cure
Prepreg
Cure Cycle
Strength
Avg. Specimen
Number
Batch #
Cycle
Lot #
#
[ksi]
Thickn. [in]
HFIHA111A*
A
M1
1
1
HFIHA112A
A
M1
1
1
37.632
0.149
HFIHA113A
A
M1
1
1
37.773
0.147
HFIHA114A
A
M1
1
1
38.392
0.147
HFIHA212A
A
M2
1
2
35.927
0.149
HFIHA213A
A
M2
1
2
37.419
0.146
HFIHA214A
A
M2
1
2
37.776
0.147
HFIHB111A
B
M1
2
1
36.276
0.144
HFIHB112A
B
M1
2
1
39.054
0.143
HFIHB113A
B
M1
2
1
39.284
0.144
HFIHB212A
B
M2
2
2
39.428
0.143
HFIHB213A
B
M2
2
2
40.133
0.144
HFIHB214A
B
M2
2
2
37.460
0.144
HFIHC111A
C
M1
3
1
39.165
0.143
HFIHC112A
C
M1
3
1
38.456
0.147
HFIHC113A
C
M1
3
1
40.851
0.146
HFIHC212A
C
M2
3
2
37.306
0.144
HFIHC213A
C
M2
3
2
39.456
0.148
HFIHC214A
C
M2
3
2
39.482
0.146
*Data from was removed due to thickness variation due to pinching on edge of panel during bagging.
Average
38.404
Standard Dev.
1.310
Coeff. of Var. [%]
3.412
Min.
35.927
Max.
40.851
Number of Spec.
18

# Plies in
Laminate

Failure
Modes

Avg. tply
[in]

Strengthnorm
[ksi]

20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20

LGM
AGM / LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM / AGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM / AGM
LGM
LGM

0.0075
0.0073
0.0073
0.0074
0.0073
0.0074
0.0072
0.0072
0.0072
0.0071
0.0072
0.0072
0.0071
0.0074
0.0073
0.0072
0.0074
0.0073

38.983
38.552
39.174
37.062
38.042
38.585
36.255
38.896
39.166
39.085
39.993
37.338
38.793
39.337
41.333
37.237
40.456
40.090

0.0073

38.799
1.276
3.290
36.255
41.333
18

Average norm
Standard Dev.norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Laminate Open Hole Compression Properties (OHC2) -- (RTD)


Normalized Strength

0.0071
0.0075
18

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

0
0

10

20

30

40

50

Laminate Open Hole Compression Strength [ksi]

Page 199 of 238

60

70

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Open Hole Compression Properties (OHC2) -- (ETW)


Strength

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Hexcel
Hexcel Cure
Prepreg
Number
Batch #
Cycle
Lot #
HFIHA117D
A
M2
1
HFIHA118D
A
M2
1
HFIHA119D
A
M2
1
HFIHA11CD
A
M2
1
HFIHA217D
A
M2
1
HFIHA218D
A
M2
1
HFIHA21AD
A
M2
1
HFIHB117D
B
M1
2
HFIHB118D
B
M1
2
HFIHB119D
B
M1
2
HFIHB217D
B
M2
2
HFIHB218D
B
M2
2
HFIHB219D
B
M2
2
HFIHC117D
C
M1
3
HFIHC118D
C
M1
3
HFIHC11AD
C
M1
3
HFIHC217D
C
M2
3
HFIHC218D*
C
M2
3
HFIHC219D
C
M2
3
HFIHC21AD
C
M2
3
reviewed data and specimens; found no cause for removal

Cure Cycle
#
2
2
2
2
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2
2
Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength
[ksi]
24.954
25.246
25.126
25.557
25.927
25.139
26.064
25.576
24.776
25.648
24.900
24.411
26.302
26.780
27.563
26.133
27.200
22.243
25.674
26.151

Avg. Specimen
Thickn. [in]
0.149
0.143
0.148
0.148
0.148
0.146
0.148
0.144
0.140
0.144
0.144
0.139
0.145
0.148
0.142
0.145
0.145
0.145
0.145
0.145

# Plies in
Laminate
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20

Failure
Modes
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM

25.568
1.125
4.399
22.243
27.563
20

Average norm
Standard Dev.norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Laminate Open Hole Compression Properties (OHC2) -- (ETW)


Normalized Strength

Avg. tply
[in]
0.0075
0.0072
0.0074
0.0074
0.0074
0.0073
0.0074
0.0072
0.0070
0.0072
0.0072
0.0069
0.0073
0.0074
0.0071
0.0073
0.0073
0.0072
0.0073
0.0072

Strengthnorm
[ksi]
25.870
25.143
25.835
26.326
26.581
25.453
26.839
25.526
24.114
25.665
24.842
23.549
26.552
27.568
27.098
26.384
27.411
22.359
25.864
26.317

0.0073

25.765
1.295
5.025
22.359
27.568
20

0.0069
0.0075
20

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
1
1

0
0

10

20

30

40

50

Laminate Open Hole Compression Strength [ksi]

Page 200 of 238

60

70

Prepreg Lot #

Cure Cycle #

3
2

CAM-RP-2009-015 April 22, 2011 Revision A

4.24 Open Hole Compression 3 Properties


Laminate Open Hole Compression Properties (OHC3) -- (RTD)
Strength

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFIIA112A
HFIIA113A
HFIIA114A
HFIIA115A
HFIIA211A
HFIIA212A
HFIIA213A
HFIIB111A
HFIIB112A
HFIIB113A
HFIIB211A
HFIIB212A
HFIIB213A
HFIIC111A
HFIIC112A
HFIIC113A
HFIIC211A
HFIIC212A
HFIIC213A

Hexcel Hexcel Cure


Batch #
Cycle
A
M1
A
M1
A
M1
A
M1
A
M2
A
M2
A
M2
B
M1
B
M1
B
M1
B
M2
B
M2
B
M2
C
M1
C
M1
C
M1
C
M2
C
M2
C
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength
[ksi]
60.942
60.721
64.256
63.061
59.243
59.063
62.584
67.551
63.679
63.819
65.022
62.890
63.372
64.202
60.008
66.739
62.358
65.106
69.243

Avg. Specimen
Thickn. [in]
0.141
0.148
0.147
0.147
0.138
0.150
0.147
0.140
0.144
0.144
0.139
0.145
0.143
0.138
0.145
0.144
0.139
0.146
0.144

# Plies in
Laminate
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20

Failure
Modes
LGM
LGM
LGM
LGM / AGM
LGM
LGM
LGM
LGM
AGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM

63.361
2.714
4.284
59.063
69.243
19

Average norm
Standard Dev. norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Avg. tply
[in]
0.0071
0.0074
0.0073
0.0074
0.0069
0.0075
0.0073
0.0070
0.0072
0.0072
0.0070
0.0073
0.0072
0.0069
0.0073
0.0072
0.0070
0.0073
0.0072

Strengthnorm
[ksi]
59.772
62.513
65.520
64.535
56.631
61.381
63.700
65.799
63.613
63.863
62.862
63.523
63.050
61.690
60.570
66.731
60.402
66.078
69.283

0.0072

63.238
2.872
4.542
56.631
69.283
19

0.0069
0.0075

Laminate Open Hole Compression Properties (OHC3) -- (RTD)


Normalized Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

0
0

20

40

60

80

100

Laminate Open Hole Compression Strength [ksi]

Page 201 of 238

120

140

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Open Hole Compression Properties (OHC3) -- (ETW)


Strength

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFIIA117D
HFIIA119D
HFIIA11AD
HFIIA11BD
HFIIA217D
HFIIA218D
HFIIA219D
HFIIB117D
HFIIB118D
HFIIB119D
HFIIB217D
HFIIB218D
HFIIB21AD
HFIIC117D
HFIIC118D
HFIIC11AD
HFIIC216D
HFIIC217D
HFIIC218D
HFIIC21AD

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2
2
Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength
[ksi]
43.892
46.817
45.668
47.637
43.825
44.311
46.269
50.124
45.102
48.963
44.869
45.558
46.396
44.907
48.614
45.907
42.659
46.524
51.350
44.945

Avg. Specimen
Thickn. [in]
0.147
0.148
0.147
0.147
0.149
0.144
0.148
0.145
0.143
0.147
0.145
0.142
0.146
0.145
0.141
0.146
0.142
0.143
0.137
0.143

# Plies in
Laminate
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20

Failure
Modes
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM

46.217
2.201
4.762
42.659
51.350
20

Average norm
Standard Dev.norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Laminate Open Hole Compression Properties (OHC3) -- (ETW)


Normalized Strength

Avg. tply
[in]
0.0074
0.0074
0.0074
0.0074
0.0074
0.0072
0.0074
0.0073
0.0071
0.0073
0.0073
0.0071
0.0073
0.0072
0.0070
0.0073
0.0071
0.0071
0.0069
0.0071

Strengthnorm
[ksi]
44.908
48.036
46.630
48.657
45.296
44.434
47.549
50.495
44.653
49.949
45.222
44.893
46.928
45.078
47.499
46.550
42.007
46.152
48.860
44.534

0.0072

46.417
2.111
4.548
42.007
50.495
20

0.0069
0.0074

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
2

0
0

10

20

30

40

50

Laminate Open Hole Compression Strength [ksi]

Page 202 of 238

60

70

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

4.25 Filled-Hole Compression 1 Properties


Laminate Filled-Hole Compression Properties (FHC1) -- (RTD)
Strength

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFI7A111A
HFI7A112A
HFI7A113A
HFI7A116A
HFI7A211A
HFI7A212A
HFI7A213A
HFI7B112A
HFI7B113A
HFI7B114A
HFI7B211A
HFI7B212A
HFI7B213A
HFI7B214A
HFI7C111A
HFI7C112A
HFI7C113A
HFI7C211A
HFI7C213A
HFI7C214A

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
2
2
2
2
1
1
1
2
2
2

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength
[ksi]
65.463
62.442
64.338
65.893
63.946
66.211
70.538
76.196
72.336
68.620
68.994
72.258
71.491
74.418
69.807
67.037
70.097
71.561
75.282
69.069

Avg. Specimen
Thickn. [in]
0.177
0.177
0.176
0.177
0.168
0.175
0.173
0.173
0.171
0.171
0.164
0.176
0.172
0.172
0.169
0.174
0.172
0.167
0.172
0.173

# Plies in
Laminate
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24

Failure
Mode
LGF
MGM
MGF
MGF
MGF
MGF
MGF
MGF
MGF
MGF
MGF
MGF
MGF
MGF
LGF
MGF
MGM
MGF
MGF
LGF

69.300
3.851
5.557
62.442
76.196
20

Average norm
Standard Dev.norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Laminate Filled-Hole Compression Properties (FHC1) -- (RTD)


Normalized Strength

Avg. tply
[in]
0.0074
0.0074
0.0073
0.0074
0.0070
0.0073
0.0072
0.0072
0.0071
0.0071
0.0068
0.0073
0.0072
0.0072
0.0070
0.0073
0.0072
0.0070
0.0072
0.0072

Strengthnorm
[ksi]
66.953
64.032
65.610
67.393
62.343
67.201
70.695
76.167
71.555
68.064
65.481
73.728
71.250
74.210
68.218
67.515
69.820
69.277
75.100
69.222

0.0072

69.192
3.693
5.338
62.343
76.167
20

0.0068
0.0074
20

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

0
0

20

40

60

80

Laminate Filled-Hole Compression Strength [ksi]

Page 203 of 238

100

120

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Filled-Hole Compression Properties (FHC1) -- (ETW)


Strength

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFI7A117D
HFI7A118D
HFI7A119D
HFI7A11AD
HFI7A216D
HFI7A218D
HFI7A219D
HFI7B116D
HFI7B117D
HFI7B119D
HFI7B216D
HFI7B217D
HFI7B21AD
HFI7C116D
HFI7C119D
HFI7C11AD
HFI7C217D
HFI7C218D
HFI7C21AD

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength
[ksi]
52.767
51.092
50.055
48.041
49.903
48.614
47.933
54.567
51.569
51.627
53.877
51.456
51.286
51.701
52.987
53.041
53.076
52.625
54.428

Avg. Specimen
Thickn. [in]
0.179
0.167
0.178
0.178
0.173
0.170
0.176
0.171
0.173
0.171
0.172
0.174
0.163
0.172
0.175
0.172
0.174
0.174
0.177

# Plies in
Laminate
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24

Failure
Mode
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM,LGF
LGM,LGF
LGM
LGM
LGM,LGO
LGM

51.613
1.990
3.855
47.933
54.567
19

Average norm
Standard Dev.norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Avg. tply
[in]
0.007
0.007
0.007
0.007
0.007
0.007
0.007
0.007
0.007
0.007
0.007
0.007
0.007
0.007
0.007
0.007
0.007
0.007
0.007

Strengthnorm
[ksi]
54.645
49.254
51.653
49.389
49.855
47.705
48.742
54.067
51.623
51.204
53.612
51.863
48.352
51.546
53.631
52.790
53.393
52.965
55.604

0.0072

51.679
2.279
4.410
47.705
55.604
19

0.0068
0.0075
19

Laminate Filled-Hole Compression Properties (FHC1) -- (ETW)


Normalized Strength
HEXCEL 8552 - IM7 UNI PREPREG
3
Cure Cycle #

Prepreg Lot #

Cure Cycle #

Prepreg Lot #

0
0

20

40

60

80

Laminate Filled-Hole Compression Strength [ksi]

Page 204 of 238

100

120

CAM-RP-2009-015 April 22, 2011 Revision A

4.26 Filled-Hole Compression 2 Properties


Laminate Filled-Hole Compression Properties (FHC2) -- (RTD)
Strength

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Hexcel Hexcel Cure Prepreg
Number
Batch #
Cycle
Lot #
HFI8A111A
A
M1
1
HFI8A112A
A
M1
1
HFI8A113A
A
M1
1
HFI8A114A
A
M1
1
HFI8A212A
A
M2
1
HFI8A213A
A
M2
1
HFI8A214A
A
M2
1
HFI8B111A
B
M1
2
HFI8B112A
B
M1
2
HFI8B113A
B
M1
2
HFI8B211A
B
M2
2
HFI8B212A
B
M2
2
HFI8B213A
B
M2
2
HFI8C111A
C
M1
3
HFI8C112A
C
M1
3
HFI8C113A
C
M1
3
HFI8C211A
C
M2
3
HFI8C215A
C
M2
3
HFI8C216A
C
M2
3
Note: HFI8A211A was not included due to bad failure.

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

Strength
[ksi]
52.194
56.130
56.315
54.064
55.486
53.907
54.713
51.968
53.821
56.128
54.346
50.572
53.535
54.090
53.683
57.536
52.267
55.097
54.892

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Avg. Specimen
Thickn. [in]
0.141
0.148
0.146
0.147
0.147
0.146
0.147
0.140
0.146
0.144
0.142
0.144
0.144
0.144
0.144
0.144
0.144
0.146
0.146

# Plies in
Laminate
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20

Failure
Mode
MGF
MGF
MGF
MGF
LGF
AGM
MGF
AGM
MGF
MGF
MGF
LGM
AGM
MGF
MGF
MGF
LGF
MGF
MGF

54.250
1.717
3.166
50.572
57.536
19

Average norm
Standard Dev.norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Avg. tply
[in]
0.0071
0.0074
0.0073
0.0074
0.0074
0.0073
0.0074
0.0070
0.0073
0.0072
0.0071
0.0072
0.0072
0.0072
0.0072
0.0072
0.0072
0.0073
0.0073

Strengthnorm
[ksi]
51.240
57.708
57.279
55.241
56.649
54.812
55.967
50.410
54.612
56.147
53.591
50.426
53.448
54.059
53.807
57.623
52.442
55.792
55.502

0.0072

54.566
2.252
4.127
50.410
57.708
19

0.0070
0.0074
19

Laminate Filled-Hole Compression Properties (FHC2) -- (RTD)


Normalized Strength
HEXCEL 8552 - IM7 UNI PREPREG

Cure Cycle #
Prepreg Lot #

1
1

0
0

10

20

30

40

50

60

70

Laminate Filled-Hole Compression Strength [ksi]

Page 205 of 238

80

90

100

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Filled-Hole Compression Properties (FHC2) -- (ETW)


Strength

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFI8A11AD
HFI8A11BD
HFI8A11CD
HFI8A11DD
HFI8A217D
HFI8A218D
HFI8A219D
HFI8B116D
HFI8B117D
HFI8B118D
HFI8B217D
HFI8B218D
HFI8B219D
HFI8C117D
HFI8C118D
HFI8C119D
HFI8C217D
HFI8C21BD
HFI8C21CD

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

Strength
[ksi]
42.022
43.199
43.160
40.875
40.631
41.624
41.044
40.181
39.512
38.952
37.862
39.184
39.181
42.391
42.392
40.212
40.523
41.263
42.118

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Avg. Specimen
Thickn. [in]
0.148
0.146
0.147
0.147
0.148
0.141
0.148
0.144
0.145
0.143
0.142
0.144
0.144
0.144
0.145
0.144
0.145
0.146
0.145

# Plies in
Laminate
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20

Failure
Mode
LGM
LGM
LGM,LGO
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
AGM,LGM
AGM,LGM
LGM
LGM
LGM
LGM

40.859
1.496
3.661
37.862
43.199
19

Average norm
Standard Dev. norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Avg. tply
[in]
0.0074
0.0073
0.0073
0.0073
0.0074
0.0070
0.0074
0.0072
0.0073
0.0072
0.0071
0.0072
0.0072
0.0072
0.0073
0.0072
0.0072
0.0073
0.0073

Strengthnorm
[ksi]
43.160
43.809
43.994
41.594
41.670
40.646
42.279
40.167
39.906
38.736
37.358
39.052
39.290
42.411
42.711
40.324
40.763
41.826
42.493

0.0073

41.168
1.809
4.394
37.358
43.994
19

0.0070
0.0074

Laminate Filled-Hole Compression Properties (FHC2) -- (ETW)


Normalized Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
1
1

0
0

10

20

30

40

50

60

70

Laminate Filled-Hole Compression Strength [ksi]

Page 206 of 238

80

90

100

Prepreg Lot #

Cure Cycle #

3
2

CAM-RP-2009-015 April 22, 2011 Revision A

4.27 Filled-Hole Compression 3 Properties


normalizing tply
[in]
0.0072

Laminate Filled-Hole Compression Properties (FHC3) -- (RTD)


Strength
HEXCEL 8552 - IM7 UNI PREPREG
Specimen
Number
HFI9A113A
HFI9A114A
HFI9A115A
HFI9A212A
HFI9A213A
HFI9A215A
HFI9B111A
HFI9B112A
HFI9B113A
HFI9B211A
HFI9B212A
HFI9B215A
HFI9C111A
HFI9C112A
HFI9C113A
HFI9C213A
HFI9C214A
HFI9C215A

Hexcel
Batch #
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength
[ksi]
100.899
102.545
93.040
98.641
102.738
87.810
94.763
96.989
99.323
101.931
99.865
100.124
99.109
104.248
100.123
95.335
92.969
96.374

Avg. Specimen
Thickn. [in]
0.147
0.147
0.148
0.149
0.147
0.147
0.139
0.144
0.143
0.140
0.143
0.143
0.140
0.147
0.145
0.145
0.145
0.145

# Plies in
Laminate
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20

Failure
Mode
MGF
MGF
MGF
MGF
MGF
MGF
MGF
MGF
MGF
MGF
MGF
MGF
MGF
MGF
MGF
MGF
LGF
MGF

98.157
4.176
4.254
87.810
104.248
18

Average norm
Standard Dev.norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Laminate Filled-Hole Compression Properties (FHC3) -- (RTD)


Normalized Strength

Avg. tply
[in]
0.0073
0.0073
0.0074
0.0074
0.0073
0.0073
0.0070
0.0072
0.0071
0.0070
0.0071
0.0072
0.0070
0.0074
0.0072
0.0073
0.0073
0.0072

Strengthnorm
[ksi]
102.756
104.456
95.603
101.826
104.807
89.446
91.494
97.202
98.369
99.264
99.033
99.556
96.631
106.541
100.517
96.284
93.668
96.843

0.0072

98.572
4.542
4.608
89.446
106.541
18

0.0070
0.0074

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

1
1

0
0

20

40

60

80

Laminate Filled-Hole Compression Strength [ksi]

Page 207 of 238

100

120

140

Prepreg Lot #

Cure Cycle #

3
2

CAM-RP-2009-015 April 22, 2011 Revision A

normalizing tply
[in]
0.0072

Laminate Filled-Hole Compression Properties (FHC3) -- (ETW)


Strength
HEXCEL 8552 - IM7 UNI PREPREG
Specimen
Number
HFI9A117D
HFI9A118D
HFI9A11AD
HFI9A11CD
HFI9A216D
HFI9A217D
HFI9A218D
HFI9B116D
HFI9B117D
HFI9B11AD
HFI9B217D
HFI9B218D
HFI9B219D
HFI9C116D
HFI9C117D
HFI9C118D
HFI9C217D
HFI9C218D
HFI9C219D

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
2
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Strength
[ksi]
69.224
74.689
71.517
70.467
70.881
71.904
70.754
71.675
72.240
73.884
73.508
69.873
69.943
77.225
74.844
75.632
72.003
72.482
68.986

Avg. Specimen
Thickn. [in]
0.148
0.146
0.149
0.146
0.146
0.143
0.147
0.144
0.145
0.143
0.142
0.145
0.143
0.146
0.146
0.144
0.145
0.144
0.148

# Plies in
Laminate
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20

Failure
Mode
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM
LGM

72.196
2.264
3.135
68.986
77.225
19

Average norm
Standard Dev.norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Avg. tply
[in]
0.0074
0.0073
0.0074
0.0073
0.0073
0.0072
0.0073
0.0072
0.0072
0.0072
0.0071
0.0072
0.0072
0.0073
0.0073
0.0072
0.0073
0.0072
0.0074

Strengthnorm
[ksi]
70.995
75.648
73.976
71.446
72.070
71.505
72.006
71.435
72.558
73.413
72.487
70.181
69.474
78.092
76.134
75.378
72.728
72.624
70.806

0.0073

72.787
2.205
3.029
69.474
78.092
19

0.0071
0.0074
19

Laminate Filled-Hole Compression Properties (FHC3) -- (ETW)


Normalized Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
1
1

0
0

10

20

30

40

50

60

70

Laminate Filled-Hole Compression Strength [ksi]

Page 208 of 238

80

90

100

Prepreg Lot #

Cure Cycle #

3
2

CAM-RP-2009-015 April 22, 2011 Revision A

4.28 Single Shear Bearing 1 Properties


Laminate Bearing Properties (SSB1) -- (RTD)
Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFI1A112A
HFI1A113A
HFI1A114A
HFI1A115A
HFI1A211A
HFI1A212A
HFI1A213A
HFI1B111A
HFI1B112A
HFI1B113A
HFI1B211A
HFI1B212A
HFI1B213A
HFI1C111A
HFI1C112A
HFI1C113A
HFI1C211A
HFI1C212A
HFI1C213A

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure Prepreg


Cycle
Lot #
M1
1
M1
1
M1
1
M1
1
M2
1
M2
1
M2
1
M1
2
M1
2
M1
2
M2
2
M2
2
M2
2
M1
3
M1
3
M1
3
M2
3
M2
3
M2
3

Cure Cycle #
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

2% Offset
Strength [ksi]
106.298
107.274
111.618
116.831
107.034
112.704
107.280
111.703
112.467
115.988
118.291
114.477
109.247
117.118
113.824
118.980
116.861
113.651
114.993

Avg. Specimen
Thickn. [in]
0.109
0.108
0.116
0.117
0.107
0.111
0.113
0.106
0.111
0.110
0.112
0.113
0.113
0.111
0.112
0.116
0.110
0.118
0.113

# Plies in
Laminate
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16

*Ultimate Strength not obtained


Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Comments

Avg. tply
[in]
0.0068
0.0068
0.0073
0.0073
0.0067
0.0070
0.007
0.007
0.0069
0.0069
0.0070
0.0071
0.0071
0.0069
0.0070
0.0073
0.0069
0.0074
0.0071

B1I / 2% OFFSET FOR UBS*


B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
Ultimate Bearing Strength / B1I:
B:Bearing, 1:first hole, I: Inapplicable
(not on bolt, nut or head side)

112.981
4.018
3.556
106.298
118.980
19

Average norm 0.0070


Standard Dev. norm
Coeff. of Var. [%]norm
Min. 0.0066
Max. 0.0074
Number of Spec.
19

Laminate Bearing Properties (SSB1) -- (RTD)


Normalized 2% Offset Strength

2% Strengthnorm
[ksi]
100.423
100.771
112.829
118.623
99.307
108.953
104.812
102.653
108.431
111.055
115.193
112.572
107.161
112.475
111.140
119.858
112.008
116.413
113.229

109.890
6.059
5.514
99.307
119.858
19

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

0
0

25

50

75

100

125

Laminate Bearing Strength (SSB1) [ksi]

Page 209 of 238

150

175

200

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Bearing Properties (SSB1) -- (ETW)


Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen

Hexcel

Hexcel Cure

Prepreg

Number
HFI1A117D
HFI1A118D
HFI1A119D
HFI1A11AD
HFI1A217D
HFI1A218D
HFI1A219D
HFI1B116D
HFI1B117D
HFI1B118D
HFI1B119D
HFI1B216D
HFI1B217D
HFI1B219D
HFI1B21AD
HFI1C116D
HFI1C117D
HFI1C118D
HFI1C216D
HFI1C217D
HFI1C218D

Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
C
C
C
C
C
C

Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M1
M2
M2
M2
M2
M1
M1
M1
M2
M2
M2

Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle #
1
1
1
1
2
2
2
1
1
1
1
2
2
2
2
1
1
1
2
2
2

2% Offset

Avg. Specimen

# Plies in

Strength [ksi]
92.906
86.483
94.390
94.925
95.782
99.813
92.654
96.354
98.015
96.256
75.485
95.780
79.089
77.542
68.615
95.379
83.578
94.145
88.240
86.389
95.743

Thickn. [in]
0.114
0.115
0.116
0.117
0.115
0.117
0.117
0.111
0.109
0.111
0.117
0.117
0.111
0.118
0.116
0.112
0.103
0.106
0.118
0.103
0.111

Laminate
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16

*Ultimate Strength not obtained


Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Comments

Avg. tply

2% Strengthnorm

[in]
0.0071
0.0072
0.0072
0.0073
0.0072
0.0073
0.007
0.0069
0.0068
0.0070
0.0073
0.0073
0.0069
0.0074
0.0073
0.0070
0.0065
0.0066
0.0074
0.0065
0.0069

[ksi]
91.858
86.520
94.827
96.339
95.491
101.128
93.699
92.813
92.329
92.997
76.642
97.595
76.125
79.191
69.191
92.771
74.945
86.354
90.423
77.440
92.211

Average norm 0.0071


Standard Dev.norm
Coeff. of Var. [%]norm
Min. 0.0065
Max. 0.0074
Number of Spec.
21

88.138
8.903
10.101
69.191
101.128
21

B1I / 2% OFFSET FOR UBS*


B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
Ultimate Bearing Strength / B1I:
B:Bearing, 1:first hole, I: Inapplicable
(not on bolt, nut or head side)

89.884
8.534
9.495
68.615
99.813
21.000

Laminate Bearing Properties (SSB1) -- (ETW)


Normalized 2% Offset Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
2

0
0

25

50

75

100

125

Laminate Bearing Strength (SSB1) [ksi]

Page 210 of 238

150

175

200

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

4.29 Single Shear Bearing 2 Properties


Laminate Bearing Properties (SSB2) -- (RTD)
Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFI2A111A
HFI2A113A
HFI2A114A
HFI2A115A
HFI2A212A
HFI2A213A
HFI2A214A
HFI2B111A
HFI2B112A
HFI2B113A
HFI2B212A
HFI2B213A
HFI2B215A
HFI2C111A
HFI2C112A
HFI2C113A
HFI2C211A
HFI2C212A
HFI2C213A

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure Prepreg Cure Cycle


2% Offset
Avg. Specimen # Plies in
Cycle
Lot #
#
Strength [ksi]
Thickn. [in]
Laminate
M1
1
1
109.784
0.146
20
M1
1
1
115.844
0.146
20
M1
1
1
119.732
0.146
20
M1
1
1
116.225
0.146
20
M2
1
2
107.330
0.147
20
M2
1
2
113.680
0.146
20
M2
1
2
116.978
0.146
20
M1
2
1
122.564
0.143
20
M1
2
1
113.243
0.145
20
M1
2
1
117.116
0.143
20
M2
2
2
111.830
0.145
20
M2
2
2
114.749
0.143
20
M2
2
2
109.087
0.142
20
M1
3
1
104.420
0.138
20
M1
3
1
114.777
0.139
20
M1
3
1
115.248
0.140
20
M2
3
2
111.985
0.139
20
M2
3
2
118.646
0.148
20
M2
3
2
116.496
0.146
20

Comments
B1I /
B1I /
B1I /
B1I /
B1I /
B1I /
B1I /
B1I /
B1I /
B1I /
B1I /
B1I /
B1I /
B1I /
B1I /
B1I /
B1I /
B1I /
B1I /

2%
2%
2%
2%
2%
2%
2%
2%
2%
2%
2%
2%
2%
2%
2%
2%
2%
2%
2%

OFFSET FOR UBS*


OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*

Avg. tply
[in]
0.0073
0.0073
0.0073
0.0073
0.0073
0.0073
0.0073
0.0071
0.0073
0.0072
0.0073
0.0072
0.0071
0.0069
0.0069
0.0070
0.0069
0.0074
0.0073

2% Strengthnorm
[ksi]
111.093
117.051
121.381
118.068
109.231
114.969
118.210
121.500
114.108
116.492
112.672
114.205
107.269
100.298
110.659
111.833
107.760
121.805
117.804

0.0072

114.021
5.566
4.882
100.298
121.805
19

Ultimate Bearing Strength / B1I:


B:Bearing, 1:first hole, I: Inapplicable
(not on bolt, nut or head side)

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

114.197
4.413
3.865
104.420
122.564
19

Average norm
Standard Dev. norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

0.0069
0.0074
19

Laminate Bearing Properties (SSB2) -- (RTD)


Normalized 2% Offset Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
1
1

0
0

25

50

75

100

125

Laminate Bearing Strength (SSB2) [ksi]

Page 211 of 238

150

175

200

Prepreg Lot #

Cure Cycle #

3
2

CAM-RP-2009-015 April 22, 2011 Revision A


Laminate Bearing Properties (SSB2) -- (ETW)
Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFI2A118D
HFI2A119D
HFI2A11AD
HFI2A11BD
HFI2A216D
HFI2A218D
HFI2A219D
HFI2B115D
HFI2B116D
HFI2B117D
HFI2B216D
HFI2B217D
HFI2B21AD
HFI2C116D
HFI2C118D
HFI2C119D
HFI2C216D
HFI2C217D
HFI2C218D

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

2% Offset
Strength [ksi]
92.682
81.650
91.223
97.233
88.887
77.484
92.381
89.332
86.144
91.640
82.833
86.520
90.471
83.364
77.965
79.807
84.712
86.483
89.800

Avg. Specimen
Thickn. [in]
0.147
0.139
0.140
0.140
0.148
0.146
0.145
0.144
0.137
0.144
0.145
0.137
0.144
0.148
0.146
0.146
0.142
0.135
0.146

# Plies in
Laminate
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20

Comments

Avg. tply
[in]
0.0074
0.0070
0.0070
0.0070
0.0074
0.0073
0.0072
0.0072
0.0068
0.0072
0.0072
0.0068
0.0072
0.0074
0.0073
0.0073
0.0071
0.0068
0.0073

B1I / 2% OFFSET FOR UBS*


B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*

2% Strengthnorm
[ksi]
94.731
78.815
88.700
94.701
91.047
78.398
92.734
89.270
81.678
91.704
83.149
82.154
90.178
85.574
79.048
80.758
83.399
81.318
90.881

Ultimate Bearing Strength / B1I:


B:Bearing, 1:first hole, I: Inapplicable
(not on bolt, nut or head side)

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

86.874
5.393
6.208
77.484
97.233
19

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Average norm 0.0071


Standard Dev.norm
Coeff. of Var. [%]norm
Min. 0.0068
Max. 0.0074
Number of Spec.
19

Laminate Bearing Properties (SSB2) -- (ETW)


Normalized 2% Offset Strength

86.223
5.624
6.522
78.398
94.731
19

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

0
0

25

50

75

100

125

Laminate Bearing Strength (SSB2) [ksi]

Page 212 of 238

150

175

200

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

4.30 Single Shear Bearing 3 Properties


Laminate Bearing Properties (SSB3) -- (RTD)
Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFI3A112A
HFI3A113A
HFI3A114A
HFI3A115A
HFI3A212A
HFI3A213A
HFI3A214A
HFI3B111A
HFI3B112A
HFI3B113A
HFI3B211A
HFI3B212A
HFI3B213A
HFI3C111A
HFI3C112A
HFI3C114A
HFI3C212A
HFI3C213A
HFI3C215A

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

2% Offset
Strength [ksi]
111.329
110.555
110.982
110.014
118.853
118.684
118.053
112.900
108.476
109.396
116.878
115.519
122.041
113.847
116.374
115.629
104.569
114.501
116.007

Avg. Specimen
Thickn. [in]
0.147
0.140
0.139
0.137
0.147
0.146
0.147
0.137
0.147
0.144
0.139
0.146
0.144
0.147
0.144
0.145
0.146
0.149
0.146

# Plies in
Laminate
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20

Comments
B1I /
B1I /
B1I /
B1I /
B1I /
B1I /
B1I /
B1I /
B1I /
B1I /
B1I /
B1I /
B1I /
B1I /
B1I /
B1I /
B1I /
B1I /
B1I /

2%
2%
2%
2%
2%
2%
2%
2%
2%
2%
2%
2%
2%
2%
2%
2%
2%
2%
2%

OFFSET FOR UBS*


OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*
OFFSET FOR UBS*

Avg. tply
[in]
0.0073
0.0070
0.0070
0.0068
0.0073
0.0073
0.007
0.007
0.0074
0.0072
0.0070
0.0073
0.0072
0.0074
0.0072
0.0072
0.0073
0.0075
0.0073

2% Strengthnorm
[ksi]
113.352
107.151
107.244
104.322
121.123
120.428
120.458
107.307
110.812
109.142
112.861
117.445
121.801
116.219
116.361
116.191
105.840
118.543
117.417

0.0072

113.896
5.710
5.014
104.322
121.801
19

Ultimate Bearing Strength / B1I:


B:Bearing, 1:first hole, I: Inapplicable
(not on bolt, nut or head side)

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

113.927
4.317
3.790
104.569
122.041
19

Average norm
Standard Dev. norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

0.0068
0.0075
19

Laminate Bearing Properties (SSB3) -- (RTD)


Normalized 2% Offset Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

2
1
1

0
0

25

50

75

100

125

Laminate Bearing Strength (SSB3) [ksi]

Page 213 of 238

150

175

200

Prepreg Lot #

Cure Cycle #

3
2

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Bearing Properties (SSB3) -- (ETW)


Strength & Modulus

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFI3A117D
HFI3A119D
HFI3A11AD
HFI3A11BD
HFI3A216D
HFI3A218D
HFI3A219D
HFI3B116D
HFI3B117D
HFI3B118D
HFI3B216D
HFI3B217D
HFI3B218D
HFI3C116D
HFI3C117D
HFI3C118D
HFI3C216D
HFI3C217D
HFI3C218D

Hexcel
Batch #
A
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
C
C
C

Hexcel Cure
Cycle
M1
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2
M1
M1
M1
M2
M2
M2

Prepreg
Lot #
1
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3

Cure Cycle
#
1
1
1
1
2
2
2
1
1
1
2
2
2
1
1
1
2
2
2

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

2% Offset
Strength [ksi]
99.478
87.757
94.216
91.661
99.866
99.109
95.924
101.302
92.665
98.556
94.921
85.275
86.622
86.888
87.638
81.004
85.372
83.126
92.797

Avg. Specimen
Thickn. [in]
0.139
0.145
0.145
0.143
0.148
0.145
0.144
0.146
0.141
0.139
0.145
0.134
0.141
0.144
0.146
0.146
0.147
0.147
0.145

# Plies in
Laminate
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20

Comments
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
B1I / 2% OFFSET FOR UBS*
Ultimate Bearing Strength / B1I:
B:Bearing, 1:first hole, I:
Inapplicable (not on bolt, nut or
head side)

91.799
6.272
6.832
81.004
101.302
19

Average norm
Standard Dev. norm
Coeff. of Var. [%]norm
Min.
Max.
Number of Spec.

Laminate Bearing Properties (SSB3) -- (ETW)


Normalized 2% Offset Strength

Avg. tply
[in]
0.0069
0.0073
0.0073
0.0071
0.0074
0.0072
0.0072
0.0073
0.0071
0.0069
0.0073
0.0067
0.0071
0.0072
0.0073
0.0073
0.0074
0.0074
0.0073

2% Strengthnorm
[ksi]
95.828
88.489
94.979
90.898
102.525
99.591
96.191
102.780
90.970
95.088
95.800
79.333
84.988
86.958
88.987
82.316
87.358
84.993
93.720

0.0072

91.673
6.556
7.152
79.333
102.780
19

0.0067
0.0074
19

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Prepreg Lot #

3
2
2
1
1

0
0

25

50

75

100

125

Laminate Bearing Strength (SSB3) [ksi]

Page 214 of 238

150

175

200

Prepreg Lot #

Cure Cycle #

CAM-RP-2009-015 April 22, 2011 Revision A

4.31 Compression Strength After Impact 1 Properties


Laminate Compression After Impact Properties (CAI) -- (RTD)
Strength

normalizing tply
[in]
0.0072

HEXCEL 8552 - IM7 UNI PREPREG


Specimen
Number
HFIKA112A
HFIKA113A
HFIKA114A
HFIKA115A
HFIKA116A
HFIKA117A
HFIKA118A

Hexcel Hexcel Cure Prepreg Cure Cycle Measured Impact Strength Avg. Specimen
Batch #
Cycle
Lot #
#
Energy (in-lbf)
[ksi]
Thickn. [in]
A
M1
1
1
261.23
30.134
0.175
A
M1
1
1
264.22
30.591
0.176
A
M1
1
1
265.46
29.761
0.177
A
M1
1
1
261.64
32.374
0.174
A
M1
1
1
266.12
29.529
0.177
A
M1
1
1
262.11
30.898
0.175
A
M1
1
1
262.37
33.434
0.175
Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

# Plies in
Laminate
24
24
24
24
24
24
24

30.960
1.439
4.649
29.529
33.434
7

Failure
Mode
LDM
LDM
LDM
LDM
LDM
LDM
LDM

Avg. tply
[in]
0.0073
0.0073
0.0074
0.0073
0.0074
0.0073
0.0073

Average norm 0.00732


Standard Dev.norm
Coeff. of Var. [%]norm
Min. 0.0073
Max. 0.0074
Number of Spec.

Strengthnorm
[ksi]
30.599
31.072
30.525
32.618
30.170
31.372
33.798
31.451
1.307
4.155
30.170
33.798
7

Laminate Compression After Impact Properties 1 (CAI1) -- (RTD)


Normalized Strength

Cure Cycle #

HEXCEL 8552 - IM7 UNI PREPREG

Cure Cycle #

0
0

10

20

30

40

50

Laminate Compression After Impact Strength (CAI) [ksi]

Page 215 of 238

60

70

80

CAM-RP-2009-015 April 22, 2011 Revision A

4.32 Interlaminar Tension Properties


Laminate Curved Beam Strength Properties (CBS) -- (CTD)
Strength
HEXCEL 8552 - IM7 UNI PREPREG
Specimen
Number
HFIMA119B
HFIMA11AB
HFIMA11BB
HFIMA11CB
HFIMA11DB
HFIMA11EB
HFIMA11FB
HFIMA11GB

Hexcel
Batch #
A
A
A
A
A
A
A
A

Hexcel Cure
Cycle
M1
M1
M1
M1
M1
M1
M1
M1

Prepreg
Lot #
1
1
1
1
1
1
1
1

Cure Cycle
#
1
1
1
1
1
1
1
1

Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Curved Beam
Strength [lb]
286.007
402.797
429.446
376.970
247.302
462.853
373.011
466.694

Interlaminar Tension
Strength [ksi]
8.970
13.144
13.340
12.066
7.635
14.709
11.782
14.018

380.635
79.141
20.792
247.302
466.694
8

11.958
2.472
20.675
7.635
14.709
8

Avg. Specimen # Plies in


Thickn. [in]
Laminate
0.151
22
0.146
22
0.152
22
0.148
22
0.153
22
0.149
22
0.150
22
0.157
22

Avg. tply
[in]
0.0069
0.0066
0.0069
0.0067
0.0070
0.0068
0.0068
0.0071
0.0069
0.0066
0.0071

Average
Min.
Max.

Laminate Interlaminar Tension Strength (ILT) -- (CTD)


Measured Strength
HEXCEL 8552 - IM7 UNI PREPREG

Cure Cycle #

Cure Cycle #

0
0

100

200

300

400

500

600

Laminate Curved Beam Strength (CBS) [lb]

Laminate Interlaminar Tension Strength (ILT) -- (CTD)


Measured Strength
HEXCEL 8552 - IM7 UNI PREPREG

Cure Cycle #

Cure Cycle #

0
0

10

Laminate Interlaminar Tension Strength (ILT) [ksi]

Page 216 of 238

12

14

16

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Curved Beam Strength Properties (CBS) -- (RTD)


Strength
HEXCEL 8552 - IM7 UNI PREPREG
Specimen
Number
HFIMA111A
HFIMA112A
HFIMA113A
HFIMA114A
HFIMA115A
HFIMA116A
HFIMA117A

Hexcel Hexcel Cure Prepreg Cure Cycle Curved Beam


Batch #
Cycle
Lot #
#
Strength [lb]
A
M1
1
1
433.114
A
M1
1
1
355.037
A
M1
1
1
345.304
A
M1
1
1
387.874
A
M1
1
1
309.813
A
M1
1
1
347.870
A
M1
1
1
318.963
Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

356.853
42.119
11.803
309.813
433.114
7

Interlaminar Tension
Strength [ksi]
13.246
10.806
10.490
11.821
9.990
10.869
10.061

Avg. Specimen # Plies in


Thickn. [in]
Laminate
0.154
22
0.155
22
0.155
22
0.155
22
0.148
22
0.152
22
0.150
22

11.041
1.149
10.410
9.990
13.246
7

Average
Min.
Max.

Avg. tply
[in]
0.0070
0.0070
0.0071
0.0070
0.0067
0.0069
0.0068
0.0069
0.0067
0.0071

Laminate Curved Beam Strength Properties (CBS) -- (RTD)


Measured Strength
HEXCEL 8552 - IM7 UNI PREPREG

Cure Cycle #

Cure Cycle #

0
0

100

200

300

400

500

600

Laminate Curved Beam Strength (CBS) [lb]

Laminate Interlaminar Tension Strength (ILT) -- (RTD)


Measured Strength
HEXCEL 8552 - IM7 UNI PREPREG

Cure Cycle #

Cure Cycle #

0
0

10

Laminate Interlaminar Tension Strength (ILT) [ksi]

Page 217 of 238

12

14

16

CAM-RP-2009-015 April 22, 2011 Revision A

Laminate Curved Beam Strength Properties (CBS) -- (ETW)


Strength
HEXCEL 8552 - IM7 UNI PREPREG
Specimen Hexcel Hexcel Cure Prepreg Cure Cycle Curved Beam
Number
Batch #
Cycle
Lot #
#
Strength [lb]
HFIMA11HD
A
M1
1
1
207.829
HFIMA11ID
A
M1
1
1
211.004
HFIMA11JD
A
M1
1
1
209.973
HFIMA11KD
A
M1
1
1
202.503
HFIMA11LD
A
M1
1
1
212.626
HFIMA11MD
A
M1
1
1
211.706
HFIMA11ND
A
M1
1
1
205.110
Average
Standard Dev.
Coeff. of Var. [%]
Min.
Max.
Number of Spec.

Interlaminar Tension
Strength [ksi]
6.391
6.608
6.601
6.192
6.715
6.490
6.230

208.679
3.729
1.787
202.503
212.626
7

Avg. Specimen # Plies in


Thickn. [in]
Laminate
0.154
22
0.151
22
0.151
22
0.154
22
0.150
22
0.154
22
0.155
22

6.461
0.199
3.077
6.192
6.715
7

Avg. tply
[in]
0.0070
0.0069
0.0069
0.0070
0.0068
0.0070
0.0071
0.0069
0.0068
0.0071

Average
Min.
Max.

Laminate Curved Beam Strength Properties (CBS) -- (ETW)


Measured Strength
HEXCEL 8552 - IM7 UNI PREPREG
Cure Cycle #

Cure Cycle #

0
0

50

100

150

200

250

300

350

400

Laminate Curved Beam Strength (CBS) [lb]

Laminate Interlaminar Tension Strength (ILT) -- (ETW)


Measured Strength
HEXCEL 8552 - IM7 UNI PREPREG

Cure Cycle #

Cure Cycle #

0
0

Laminate Interlaminar Tension Strength (ILT) [ksi]

Page 218 of 238

10

CAM-RP-2009-015 April 22, 2011 Revision A

5. Shear Stress vs. Shear Strain, RTD

Shear Stress (psi)

Shear Stress vs Shear Strain


25000
20000
15000
10000
5000
0
0

20000

40000

Shear Strain (micro in/in)

Page 219 of 238

60000

CAM-RP-2009-015 April 22, 2011 Revision A

6. FLUID SENSITIVITY COMPARISON


Average Short Beam

Same Environment Short Beam Strength Worst Case Environment Short % Strength Reduction With

Fluid
a
b
c
d
e
f
g
h
i
j
k
l
r
A
t

a
b
c
d
e
f
g
h
i
j
k
l
r
A
t

Strength With Fluid (ksi)


18.131
16.821
16.749
16.561
16.480
16.221
15.835
16.586
15.852
16.804
16.794
16.297
15.819
16.962
14.811

Without Fluid (ksi) (ETD)


16.96
16.96
16.96
16.96
16.96
16.96
16.96
16.96
16.96
16.96
16.96
16.96
16.96
16.96
16.96

100 Low lead Fuel


SAE AMS 2629 JRF
Mil-PRF-5606 Hydraulic Oil
Mil-PRF-83282 Hydraulic Oil
Engine Lube Oil Mil-L-7808
Engine Lube Oil Mil-L-23699
Salt Water
Skydrol LD-4
50% Water + 50% Skydrol
MEK Washing Fluid
Polypropylene Glycol Deicer
Isopropyl Alcohol Deicing Agent
Distilled Water
Dry (Room Temp)
160F5F(85%5%) until Equilibrium

Page 220 of 238

Beam Strength (ksi) (ETW)


14.81
14.81
14.81
14.81
14.81
14.81
14.81
14.81
14.81
14.81
14.81
14.81
14.81
14.81
14.81

Respect to ETD (no fluid)


-6.895
0.828
1.252
2.361
2.843
4.369
6.643
2.214
6.545
0.930
0.989
3.916
6.735
0.000
12.681

CAM-RP-2009-015 April 22, 2011 Revision A


Average Short Beam

Same Environment Short Beam

Strength With Fluid (ksi)


10.630
11.298
11.053
10.934
10.442
10.451
9.847
10.463
9.527
11.050
11.133
11.120
9.642
11.008
8.193

Strength Without Fluid (ksi) (ETD)


11.008
11.008
11.008
11.008
11.008
11.008
11.008
11.008
11.008
11.008
11.008
11.008
11.008
11.008
11.008

Worst Case Environment Short % Strength Reduction With

Fluid
1
2
3
4
5
6
7
8
9
m
n
p
s
C
D

1
2
3
4
5
6
7
8
9
m
n
p
s
C
D

Beam Strength (ksi) (ETW)


8.193
8.193
8.193
8.193
8.193
8.193
8.193
8.193
8.193
8.193
8.193
8.193
8.193
8.193
8.193

100 Low lead Fuel


SAE AMS 2629 JRF
Mil-PRF-5606 Hydraulic Oil
Mil-PRF-83282 Hydraulic Oil
Engine Lube Oil Mil-L-7808
Engine Lube Oil Mil-L-23699
Salt Water
Skydrol LD-4
50% Water + 50% Skydrol
MEK Washing Fluid
Polypropylene Glycol Deicer
Isopropyl Alcohol Deicing Agent
Distilled Water
Dry (Room Temp)
160F5F(85%5%) until Equilibrium

Page 221 of 238

Respect to ETD (no fluid)


3.429
-2.635
-0.413
0.674
5.135
5.062
10.542
4.952
13.454
-0.381
-1.135
-1.018
12.407
0.000
25.574

CAM-RP-2009-015 April 22, 2011 Revision A


Fluid Sensitivity Screening
Short Beam Strength Properties (FSBS) -- (RTD) Strength
HEXCEL 8552 - IM7 UNI PREPREG
Specimen
Number
HFIQA121a
HFIQA122a
HFIQA123a
HFIQA124a
HFIQA125a
HFIQA126a
HFIQA12Jb
HFIQA12Kb
HFIQA12Lb
HFIQA12Mb
HFIQA12Nb
HFIQA12Ob
HFIQA131c
HFIQA132c
HFIQA133c
HFIQA134c
HFIQA135c
HFIQA136c
HFIQA13Dd
HFIQA13Ed
HFIQA13Fd
HFIQA13Gd
HFIQA13Hd
HFIQA13Id
HFIQA141e
HFIQA142e
HFIQA143e
HFIQA144e
HFIQA145e
HFIQA146e
HFIQA14Df
HFIQA14Ef
HFIQA14Ff
HFIQA14Gf
HFIQA14Hf
HFIQA14If
HFIQA151g
HFIQA152g
HFIQA153g
HFIQA154g
HFIQA155g
HFIQA156g
HFIQA15Dh
HFIQA15Eh
HFIQA15Fh
HFIQA15Gh
HFIQA15Hh
HFIQA15Ih
HFIQA161i
HFIQA162i
HFIQA163i
HFIQA164i
HFIQA165i
HFIQA16Dj
HFIQA16Ej
HFIQA16Fj
HFIQA16Gj
HFIQA16Hj
HFIQA16Ij
HFIQA171k
HFIQA172k
HFIQA173k
HFIQA174k
HFIQA175k
HFIQA176k
HFIQA17DL
HFIQA17EL
HFIQA17FL
HFIQA17GL
HFIQA17HL
HFIQA17IL
HFIQA181r
HFIQA182r
HFIQA183r
HFIQA184r
HFIQA185r
HFIQA186r
HFIQA18DA
HFIQA18EA
HFIQA18FA
HFIQA18GA
HFIQA18HA
HFIQA18IA
HFIQA191t
HFIQA192t
HFIQA193t
HFIQA194t
HFIQA195t
HFIQA196t

Hexcel
Batch #
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A

Hexcel Cure
Cycle
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1

Prepreg
Lot #
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1

Fluid
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3
4
4
4
4
4
4
5
5
5
5
5
5
6
6
6
6
6
6
7
7
7
7
7
7
8
8
8
8
8
8
9
9
9
9
9
10
10
10
10
10
10
11
11
11
11
11
11
12
12
12
12
12
12
13
13
13
13
13
13
14
14
14
14
14
14
15
15
15
15
15
15

Strength
[ksi]
21.418
17.274
17.170
17.648
17.687
17.589
16.630
16.780
16.647
16.886
16.931
17.053
16.482
16.659
16.777
16.804
16.651
17.121
16.450
16.582
16.250
16.805
16.287
16.993
16.326
16.538
16.367
16.283
16.436
16.928
16.064
16.548
16.399
16.014
16.087
16.213
15.457
16.263
14.951
15.984
15.915
16.441
16.374
16.910
16.811
16.291
16.567
16.564
16.090
16.125
15.797
15.769
15.476
17.656
17.078
16.641
16.892
16.266
16.290
16.905
16.930
16.382
16.512
17.143
16.891
16.419
16.410
16.230
16.639
15.845
16.241
15.918
15.536
15.983
15.599
15.765
16.116
16.659
16.852
16.800
16.898
17.201
17.359
15.132
14.993
14.716
15.192
13.958
14.874

Avg. Specimen
Thickn. [in]
0.200
0.212
0.223
0.233
0.238
0.241
0.216
0.226
0.237
0.245
0.251
0.254
0.256
0.257
0.257
0.257
0.257
0.257
0.214
0.224
0.234
0.243
0.249
0.251
0.253
0.251
0.247
0.242
0.235
0.226
0.251
0.252
0.252
0.252
0.253
0.253
0.216
0.227
0.236
0.243
0.248
0.251
0.253
0.251
0.247
0.243
0.235
0.226
0.252
0.252
0.252
0.252
0.252
0.215
0.226
0.235
0.243
0.248
0.251
0.252
0.251
0.248
0.243
0.237
0.229
0.253
0.253
0.252
0.253
0.253
0.253
0.213
0.226
0.235
0.243
0.248
0.251
0.253
0.251
0.248
0.243
0.236
0.227
0.252
0.253
0.253
0.252
0.252
0.253

# Plies in
Laminate
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34

Avg. tply
[in]
0.0059
0.0062
0.0066
0.0068
0.0070
0.0071
0.0063
0.0066
0.0070
0.0072
0.0074
0.0075
0.0075
0.0076
0.0076
0.0076
0.0075
0.0076
0.0063
0.0066
0.0069
0.0071
0.0073
0.0074
0.0074
0.0074
0.0073
0.0071
0.0069
0.0067
0.0074
0.0074
0.0074
0.0074
0.0074
0.0074
0.0064
0.0067
0.0069
0.0072
0.0073
0.0074
0.0074
0.0074
0.0073
0.0071
0.0069
0.0066
0.0074
0.0074
0.0074
0.0074
0.0074
0.0063
0.0066
0.0069
0.0071
0.0073
0.0074
0.0074
0.0074
0.0073
0.0071
0.0070
0.0067
0.0074
0.0074
0.0074
0.0075
0.0074
0.0074
0.0063
0.0066
0.0069
0.0071
0.0073
0.0074
0.0074
0.0074
0.0073
0.0071
0.0069
0.0067
0.0074
0.0074
0.0074
0.0074
0.0074
0.0074

Average
Min
Max

0.0071
0.0059
0.0076

Page 222 of 238

Failure
Mode
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR

18.131

16.821

16.749

16.561

16.480

16.221

15.835

16.586

15.852

16.804

16.794

16.297

15.819

16.962

14.811

CAM-RP-2009-015 April 22, 2011 Revision A

Fluid Sensitivity Screening


Short Beam Strength Properties (FSBS) -- (ETD) Strength
HEXCEL 8552 - IM7 UNI PREPREG
Specimen
Number
HFIQA1271
HFIQA1281
HFIQA1291
HFIQA12A1
HFIQA12B1
HFIQA12C1
HFIQA12D2
HFIQA12E2
HFIQA12F2
HFIQA12G2
HFIQA12H2
HFIQA12I2
HFIQA1373
HFIQA1383
HFIQA1393
HFIQA13A3
HFIQA13B3
HFIQA13C3
HFIQA13J4
HFIQA13K4
HFIQA13L4
HFIQA13M4
HFIQA13N4
HFIQA13O4
HFIQA1475
HFIQA1485
HFIQA1495
HFIQA14A5
HFIQA14B5
HFIQA14C5
HFIQA14J6
HFIQA14K6
HFIQA14L6
HFIQA14M6
HFIQA14N6
HFIQA14O6
HFIQA1577
HFIQA1587
HFIQA1597
HFIQA15A7
HFIQA15B7
HFIQA15C7
HFIQA15J8
HFIQA15K8
HFIQA15L8
HFIQA15M8
HFIQA15N8
HFIQA15O8
HFIQA1679
HFIQA1689
HFIQA1699
HFIQA16A9
HFIQA16B9
HFIQA16C9
HFIQA16Jm
HFIQA16Km
HFIQA16Lm
HFIQA16Mm
HFIQA16Nm
HFIQA16Om
HFIQA177n
HFIQA178n
HFIQA179n
HFIQA17An
HFIQA17Bn
HFIQA17Cn
HFIQA17Jp
HFIQA17Kp
HFIQA17Lp
HFIQA17Mp
HFIQA17Np
HFIQA17Op
HFIQA187s
HFIQA188s
HFIQA189s
HFIQA18As
HFIQA18Bs
HFIQA18Cs
HFIQA18JC
HFIQA18KC
HFIQA18LC
HFIQA18MC
HFIQA18NC
HFIQA18OC
HFIQA197D
HFIQA198D
HFIQA199D
HFIQA19AD
HFIQA19BD
HFIQA19CD

Hexcel
Batch #
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A

Hexcel Cure
Cycle
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1
MH1

Prepreg
Lot #
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1

Fluid
1
1
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3
4
4
4
4
4
4
5
5
5
5
5
5
6
6
6
6
6
6
7
7
7
7
7
7
8
8
8
8
8
8
9
9
9
9
9
9
10
10
10
10
10
10
11
11
11
11
11
11
12
12
12
12
12
12
13
13
13
13
13
13
14
14
14
14
14
14
15
15
15
15
15
15

Strength
[ksi]
10.925
11.029
10.866
8.809
11.063
11.090
11.334
11.269
11.302
11.200
11.603
11.080
11.415
11.188
11.167
10.870
10.971
10.708
11.031
10.999
10.744
10.975
10.913
10.939
10.534
10.598
10.451
10.467
10.248
10.357
10.398
10.327
10.047
10.455
10.712
10.764
9.993
9.909
9.651
9.877
9.774
9.880
10.641
10.674
10.532
10.321
10.386
10.221
9.691
9.274
9.467
9.419
9.633
9.675
11.079
11.226
10.934
11.036
10.943
11.081
11.388
11.276
11.319
11.043
10.959
10.811
11.070
11.014
11.074
11.082
11.290
11.189
9.424
9.683
9.554
9.697
9.712
9.783
11.122
10.883
10.986
11.400
10.839
10.817
8.335
8.207
8.324
7.842
8.293
8.154

Avg. Specimen
Thickn. [in]
0.243
0.242
0.243
0.242
0.242
0.243
0.243
0.240
0.236
0.231
0.224
0.214
0.256
0.254
0.251
0.245
0.237
0.228
0.253
0.253
0.253
0.254
0.253
0.253
0.214
0.225
0.234
0.241
0.247
0.251
0.252
0.250
0.247
0.241
0.234
0.226
0.252
0.253
0.253
0.252
0.253
0.253
0.216
0.226
0.234
0.243
0.248
0.251
0.252
0.251
0.248
0.244
0.236
0.227
0.253
0.253
0.253
0.252
0.252
0.252
0.214
0.225
0.235
0.244
0.248
0.252
0.252
0.251
0.248
0.243
0.237
0.228
0.252
0.253
0.252
0.252
0.252
0.253
0.215
0.225
0.236
0.244
0.248
0.251
0.252
0.252
0.247
0.243
0.235
0.225

# Plies in
Laminate
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34
34

Avg. tply
[in]
0.0071
0.0071
0.0071
0.0071
0.0071
0.0071
0.0072
0.0071
0.0069
0.0068
0.0066
0.0063
0.0075
0.0075
0.0074
0.0072
0.0070
0.0067
0.0074
0.0075
0.0075
0.0075
0.0075
0.0074
0.0063
0.0066
0.0069
0.0071
0.0073
0.0074
0.0074
0.0074
0.0073
0.0071
0.0069
0.0066
0.0074
0.0074
0.0074
0.0074
0.0074
0.0074
0.0063
0.0066
0.0069
0.0071
0.0073
0.0074
0.0074
0.0074
0.0073
0.0072
0.0069
0.0067
0.0074
0.0074
0.0074
0.0074
0.0074
0.0074
0.0063
0.0066
0.0069
0.0072
0.0073
0.0074
0.0074
0.0074
0.0073
0.0071
0.0070
0.0067
0.0074
0.0075
0.0074
0.0074
0.0074
0.0074
0.0063
0.0066
0.0069
0.0072
0.0073
0.0074
0.0074
0.0074
0.0073
0.0071
0.0069
0.0066

Average
Min
Max

0.0071
0.0063
0.0075

Page 223 of 238

Failure
Mode
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR / COMPRESSION
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR / COMPRESSION
INTERLAMINAR SHEAR / COMPRESSION
INTERLAMINAR SHEAR / COMPRESSION
INTERLAMINAR SHEAR / COMPRESSION
INTERLAMINAR SHEAR / COMPRESSION
INTERLAMINAR SHEAR / COMPRESSION
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR / COMPRESSION
INTERLAMINAR SHEAR / COMPRESSION
INTERLAMINAR SHEAR / COMPRESSION
INTERLAMINAR SHEAR / COMPRESSION
INTERLAMINAR SHEAR / COMPRESSION
INTERLAMINAR SHEAR / COMPRESSION
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR / COMPRESSION
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR
INTERLAMINAR SHEAR

10.630

11.298

11.053

10.934

10.442

10.451

9.847

10.463

9.527

11.050

11.133

11.120

9.642

11.008

8.193

CAM-RP-2009-015 April 22, 2011 Revision A

Load vs Displacement Curves for 90 Day RT Specimens


3500

One Sample Selected


per fluid type

3000

100 Low level AV


Fuel
SAE AMS 2629 JET
REF Fluid
MIL 5606
hyrdaulic
DRY

2500

2000
Load (lbf)

MIL 83282
hyrdaulic
MIL 7808 Engine
Oil
MIL 23699 Engine
Oil
Salt Water

1500

1000

500

SKYDROL LD-4
50% Water, 50%
SKYDROL LD-4
Distilled Water

0
0

0.01

0.02

0.03
0.04
Displacement (in)

0.05

0.06

0.07

Load vs Displacement Curves for 90 Day ETD (250F) Specimens


2500

One Sample Selected


per fluid type
100 Low level AV Fuel

2000

SAE AMS 2629 JET REF


Fluid
MIL 5606 hyrdaulic

Load (lbf)

1500
DRY
MIL 83282 Hydraulic

1000

MIL 7808 Engine Oil


MIL 23699 Engine Oil

500

Salt Water
SKYDROL LD-4

0
0

0.01

0.02

0.03

0.04

0.05

Displacement (in)

Page 224 of 238

0.06

0.07

50% Water, 50%


SKYDROL LD-4
Distilled Water

CAM-RP-2009-015 April 22, 2011 Revision A

Load vs Displacement Curves for 90 min. RT Specimens


3500

3000

One Sample Selected


per fluid type

Load (lbf)

2500

2000
MEK Washing Fluid ASTM D740
Polypropylene Glycol Deicer

1500

1000

500

0
-0.01

0.01

0.02

0.03

0.04

0.05

Displacement (in)

Load vs Displacement Curves for 90 min. ETD (250F) Specimens


2000
1800
1600
1400

One Sample Selected


per fluid type

Load (lbf)

1200
MEK Washing Fluid ASTM D740

1000

Polypropylene Glycol Deicer

800
600
400
200
0
0

0.01

0.02

0.03

0.04

Displacement (in)

Page 225 of 238

0.05

0.06

CAM-RP-2009-015 April 22, 2011 Revision A

Load vs Displacement Curves, RT, 48hrs 4hrs


3500
3000

Load (lbf)

2500

One Sample Selected


per fluid type

2000
1500

ISOPROPYL ALCOHOL Deicing Agent

1000
500
0
-0.005

0.005

0.01

0.015

0.02

0.025

0.03

0.035

0.04

0.045

0.05

Displacement (in)

Load vs Displacement Curves, ETD, 48hrs 4hrs


2000
1800
1600
1400

One Sample Selected


per fluid type

Load (lbf)

1200
1000

ISOPROPYL ALCOHOL Deicing Agent

800
600
400
200
0
-0.005

0.005

0.01

0.015

0.02

0.025

0.03

0.035

Displacement (in)

Page 226 of 238

0.04

0.045

CAM-RP-2009-015 April 22, 2011 Revision A

85% Relative Humidity @ RT


3000

2500

Load (lbf)

2000

One Sample Selected


per fluid type
1500
85% Relative Humidity @ RT

1000

500

0
0

0.01

0.02

0.03

0.04

0.05

0.06

Displacement (in)

85% Relative Humidity @250F


1600
1400
1200

Load (lbf)

1000

One Sample Selected


per fluid type

800
85% Relative Humidity @250F

600
400
200
0
0

0.01

0.02

0.03

0.04

0.05

Displacement (in)

Page 227 of 238

0.06

0.07

CAM-RP-2009-015 April 22, 2011 Revision A

7. MOISTURE CONDITIONING CHARTS


7.1 In-Plane Shear Thinnest Panel

1.0
0.9

% Weight Gain (Total)

0.8
0.7
0.6
0.5
0.4
0.3

HFINA1
HFINA2

0.2

HFINB1
HFINB2

0.1

HFINC1
HFINC2

0.0
0

10

20

30

40
Time (days)

Page 228 of 238

50

60

70

CAM-RP-2009-015 April 22, 2011 Revision A

7.2 Short Beam Strength- Thickest Panel

1.2

% Weight Gain (Total)

1.0

0.8

0.6

0.4
HFIQA11xD
HFIQA21xD
HFIQB11xD

0.2

HFIQB21xD
HFIQC11xD
HFIQC21xD

0.0
0

20

40

60

80
100
Time (days)

120

140

160

The rest of the curves can be found on the CD that accompanies this report.

Page 229 of 238

180

CAM-RP-2009-015 April 22, 2011 Revision A

8. DMA Results
The charts and graphs below are only examples. The remaining files can be obtained
from the CD provided with this report.

DMA Results Summary


Hexcel / Cessna HF 071105C1 (TT) Wet
Sample #
HFIDA 11
HFIDA 21
HFIDB 11
HFIDB 21
HFIDC 11
HFIDC 21

Onset Storage Modulus


Average
Tg [C]
Tg [F]
160.50
320.90
159.82
319.67
160.28
320.50
158.75
317.74
159.21
318.57
158.27
316.88
AVERAGE
319.04

Peak of Tangent Delta


Average
Tg [C]
Tg [F]
174.65
346.36
173.38
344.08
172.74
342.93
171.56
340.80
172.69
342.83
171.91
341.43

DMA Results Summary


Hexcel / Cessna HF 071105C1 (UNT3) Wet
Sample #
HFIDA 11
HFIDA 21
HFIDB 11
HFIDB 21
HFIDC 11
HFIDC 21

Onset Storage Modulus


Average
Tg [C]
Tg [F]
162.39
324.30
161.98
323.56
162.03
323.65
161.46
322.63
161.68
323.02
163.09
325.55
AVERAGE
323.79

Table 8-1: DMA Wet Results

Page 230 of 238

Peak of Tangent Delta


Average
Tg [C]
Tg [F]
178.21
352.77
176.77
350.19
176.59
349.85
177.09
350.76
176.25
349.24
177.15
350.87

CAM-RP-2009-015 April 22, 2011 Revision A

DMA Results Summary


Hexcel / Cessna HF 071105C1 (TT) Dry
Sample #
HFIDA 11
HFIDA 21
HFIDB 11
HFIDB 21
HFIDC 11
HFIDC 21

Onset Storage Modulus


Average
Tg [C]
Tg [F]
207.27
405.08
209.23
408.61
209.35
408.82
207.37
405.26
204.70
400.45
206.82
404.28
AVERAGE
405.41

Peak of Tangent Delta


Average
Tg [C]
Tg [F]
228.19
442.73
231.93
449.47
231.76
449.16
231.58
448.84
232.99
451.37
233.50
452.30

DMA Results Summary


Hexcel / Cessna HF 071105C1 (UNT3) Dry
Sample #
HFIDA 11
HFIDA 21
HFIDB 11
HFIDB 21
HFIDC 11
HFIDC 21

Onset Storage Modulus


Average
Tg [C]
Tg [F]
209.37
408.87
208.99
408.17
206.87
404.37
210.96
411.73
207.34
405.21
207.94
406.28
AVERAGE
407.44

Table 8-2: DMA Dry Results

Page 231 of 238

Peak of Tangent Delta


Average
Tg [C]
Tg [F]
234.62
454.31
234.89
454.79
235.17
455.31
236.27
457.29
235.41
455.74
235.60
456.08

CAM-RP-2009-015 April 22, 2011 Revision A

8.1 DMA Wet Batch A

Page 232 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

8.2 DMA Dry Batch A

Page 233 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

9. TMA Results
The TMA results were tested at Hexcel. Specimens were taken from the same panels
as DMA and wet and dry testing was tested concurrently.
4/23/2008

Wet Specimens tested for Tg by TMA to HSP-T2 (NMS 128)


Sample ID
HF071105C1 IAU2 2 HFITA21
HF071105C1 IAU2 2 HFITA21
HF071105C1 IBU1 1 HFITB11
HF071105C1 IBU1 1 HFITB11
HF071105C1 IAU1 1 HFITA 11
HF071105C1 IAU1 1 HFITA 11
HF071105C1 IBU12 2
HF071105C1 IBU12 2
HF071105C1 ICU1 1 HFITC 11
HF071105C1 ICU1 1 HFITC 11
HF071105C1 ICU2 2 HFITC 21
HF071105C1 ICU2 2 HFITC 21
HF071105C1 IAC1 1 HFITA 11
HF071105C1 IAC1 1 HFITA 11
HF071105C1 ICC2 2 HFITC 21
HF071105C1 ICC2 2 HFITC 21
HF071105C1 IAC2 2 HFITA 21
HF071105C1 IAC2 2 HFITA 21
HF071105C1 IAC1 1 HFITC 11
HF071105C1 IAC1 1 HFITC 11
HF071105C1 IBC1 1 HFITB 11
HF071105C1 IBC1 1 HFITB 11
HF071105C1 IBC2 2 HFITB 21
HF071105C1 IBC2 2 HFITB 21

Rep
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2

Thickness (mm) Tg (Deg C)


0.1036
222.25
0.1346
217.89
0.1863
218.91
0.1715
215.32
0.1652
220.96
0.1482
221.02
0.1910
216.55
0.1783
214.33
0.1585
219.76
0.1477
213.09
0.1644
217.99
0.1614
218.01
0.1627
221.11
0.1707
219.45
0.1464
221.74
0.1825
221.36
0.1702
212.45
0.1658
213.08
0.1432
219.08
0.1321
219.56
0.1750
212.53
0.1785
215.45
0.1492
218.42
0.1427
219.38

AVERAGE

432.05
424.20
426.04
419.58
429.73
429.84
421.79
417.79
427.57
415.56
424.38
424.42
430.00
427.01
431.13
430.45
414.41
415.54
426.34
427.21
414.55
419.81
425.16
426.88

Avg
428.13
422.81
429.78
419.79
421.57
424.40
428.50
430.79
414.98
426.78
417.18
426.02

424.23

Table 9-1: Wet TMA Results

Page 234 of 238

CAM-RP-2009-015 April 22, 2011 Revision A


1/21/2008

Summary of Dry NCAMP Supplied Tg (TMA) Specimens


Specimen ID
HF-H12-TMA-A-M1-Dry (TT)
HF-H12-TMA-A-M2-Dry (TT)
HF-H12-TMA-B-M1-Dry (TT)
HF-H12-TMA-B-M2-Dry (TT)
HF-H12-TMA-C-M1-Dry (TT)
HF-H12-TMA-C-M2-Dry (TT)
HF-H12-TMA-A-M1-Dry (UNT3)
HF-H12-TMA-A-M2-Dry (UNT3)
HF-H12-TMA-B-M1-Dry (UNT3)
HF-H12-TMA-B-M2-Dry (UNT3)
HF-H12-TMA-C-M1-Dry (UNT3)
HF-H12-TMA-C-M2-Dry (UNT3)

Rep
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2
1
2

Tg
214.91
217.80
216.52
219.96
217.71
214.73
215.29
214.37
212.16
209.56
215.03
219.66
221.79
223.48
221.24
217.95
212.86
213.11
220.95
219.50
216.67
218.62
217.71
216.90

Avg
216.36

421.44

218.24

424.83

216.22

421.20

214.83

418.69

210.86

411.55

217.35

423.22

222.64

432.74

219.60

427.27

212.99

415.37

220.23

428.41

217.65

423.76

217.31

423.15

AVERAGE
AVERAGE

422.64

Table 9-2: Dry TMA Results

Page 235 of 238

Test Date Time


1/19/2008 1:36
1/19/2008 0:37
1/19/2008 1:54
1/19/2008 2:11
1/19/2008 2:35
1/19/2008 3:17
1/19/2008 3:42
1/19/2008 4:23
1/19/2008 5:02
1/19/2008 5:19
1/19/2008 5:35
1/19/2008 5:52
1/21/2008 7:09
1/21/2008 7:24
1/21/2008 7:41
1/21/2008 7:58
1/21/2008 8:16
1/21/2008 8:34
1/21/2008 8:51
1/21/2008 9:06
1/21/2008 9:53
1/21/2008 10:09
1/21/2008 10:37
1/21/2008 10:52

Operator
KV
KV
KV
KV
KV
KV
KV
KV
KV
KV
KV
KV
KV
KV
KV
KV
KV
KV
KV
KV
KV
KV
KV
KV

CAM-RP-2009-015 April 22, 2011 Revision A

9.1 TMA Wet Batch A Results

9.2 TMA Wet Batch A Results

Page 236 of 238

CAM-RP-2009-015 April 22, 2011 Revision A

10. Physical Test Results


The following physical test results were obtained at Hexcel. Remaining results required
per section 4 of the test plan can be found on the CD accompanying this report.
NMS 128/2 Rev.- IM7G/8552
Type35, Class1, Grade190
IM7G
8552
Lot
spl rep Date
Ind
Avg Test ID Ind
P6942-4SQ 1
1
25-Jan-07
12
12 GEL350 13.26
P6942-4SQ
2
25-Jan-07
12
GEL350 12.98
3
13.5
P6942-4SQ 16
1
25-Jan-07
12
12 GEL350 13.12
P6942-4SQ
2
25-Jan-07
12
GEL350 12.95
3
13.1
P6944
1
1
2-Mar-07
13
13 GEL350 13.69
P6944
2
2-Mar-07
13
GEL350 11.38
3
12
P6944
14
1
2-Mar-07
12 12.2 GEL350 13.17
P6944
2
2-Mar-07 12.5
GEL350 11.34
3
10.6
P7059
1
1
1-Mar-07 12.75 12.6 GEL350 14.42
P7059
2
1-Mar-07 12.5
GEL350 14.95
3
14.87
P7059
16
1
1-Mar-07
13
13 GEL350 15.72
P7059
2
1-Mar-07
13
GEL350 16.27

Avg
Test ID
13.25 X_FLOW350B
X_FLOW350B
X_FLOW350B
13.06 X_FLOW350B
X_FLOW350B
X_FLOW350B
12.36 X_FLOW350B
X_FLOW350B
X_FLOW350B
11.7 X_FLOW350B
X_FLOW350B
X_FLOW350B
14.75 X_FLOW350B
X_FLOW350B
X_FLOW350B
16.38 X_FLOW350B
X_FLOW350B

Ind
0.688
0.615
0.831
0.966
0.931
1.045
0.556
0.57
0.589
0.569
0.495
0.438
0.46
0.645
0.642
0.733
0.601

Table 10-1: Hexcel Physical Testing Results

Page 237 of 238

Avg
Test ID
0.711 X_VOL350P
X_VOL350P
X_VOL350P
0.981 X_VOL350P
X_VOL350P
X_VOL350P
0.572 X_VOL350P
X_VOL350P
X_VOL350P
0.501 X_VOL350P
X_VOL350P
X_VOL350P
0.582 X_VOL350P
X_VOL350P
X_VOL350P
0.59 X_VOL350P
X_VOL350P

CAM-RP-2009-015 April 22, 2011 Revision A

11. Deviations
1. For fluid sensitivity testing, the Jet Reference fluid called out in the NCAMP test
plan is a rare fuel and therefore extremely expensive. As a replacement, we used
Jet Fuel A per ASTM D1655. AMS2629 is a jet reference fuel intended to
simulate jet engine fuel only. This was approved by all participating panel
fabricators.
2. For the ETW testing, it was discovered that the original adhesive used to bond the strain
gauges was not rated for the 250 degree F testing. Therefore, specimens were
refabricated and retested for modulus. This caused a delay in the program due the time
required to recondition and retest the specimens. Below is a summary of what decisions
were made affecting this Hexcel 8552 program.

o CLCs Gauge bonded with M Bond 600, cured for 1 hour 30 minutes at
300F
o Gauges were be applied before drying and then moisture conditioned.
o Previously Tested CLC specimens - Hot Dry 250F : NCAMP looked for
scraps for modulus specimens more specimens were found and
retested
o ALL CLC specimens with Hot Wet 250F testing required 6 specimens per
panel; 3 for modulus (gauged) and 3 for strength (not gauged). The
number of specimens were doubled because the protective coating
applied on the gage might prevent (or slow down) moisture absorption rate
in the gauged section.

Page 238 of 238

You might also like