You are on page 1of 32

Millennium 4 Mnl M4092 rev

1/22/03

9:38 AM

MILLENNIUM 4
Universal Remote Control

Users Guide

Page 1

Millennium 4 Mnl M4092 rev

1/22/03

9:38 AM

TABLE OF CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Features And Functions . . . . . . . . . . . . . . . . . . . . . . 4
Key Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Programming TV Control . . . . . . . . . . . . . . . . . . . . . 8
Setup Codes for TVs . . . . . . . . . . . . . . . . . . . . . . . . 8
Programming VCR/DVD Player Control . . . . . . . . 12
Setup Codes for VCRs. . . . . . . . . . . . . . . . . . . . . . 13
Setup Codes for DVD Players. . . . . . . . . . . . . . . . . 15
Programming TV/VCR Combo Control . . . . . . . . 16
Setup Codes for TV/VCRs . . . . . . . . . . . . . . . . . . . 17

Programming Cable Converter


(or DBS Receiver) Control . . . . . . . . . . . . . . . . . . . 18
To Unlock the CBL Key. . . . . . . . . . . . . . . . . . . . . . 18
To Program the CBL Key . . . . . . . . . . . . . . . . . . . . 19
To Lock the CBL Key . . . . . . . . . . . . . . . . . . . . . . . 20
Setup Codes for Cable Converters. . . . . . . . . . . . . 20
Setup Codes for DBS Receivers. . . . . . . . . . . . . . . 20
Programming Channel Control Lock . . . . . . . . . . 21
To Activate Channel Control Lock . . . . . . . . . . . . . 21
To De-Activate Channel Control Lock. . . . . . . . . . . 21
Programming Audio Control . . . . . . . . . . . . . . . . . 22
Setup Codes for Audio Amplifiers . . . . . . . . . . . . . 22
Setup Codes for Audio Receivers. . . . . . . . . . . . . . 23
Searching For Your Code . . . . . . . . . . . . . . . . . . . . 24
Checking The Codes . . . . . . . . . . . . . . . . . . . . . . . 25
Re-Assigning Device Keys . . . . . . . . . . . . . . . . . . 26
Changing Volume Lock . . . . . . . . . . . . . . . . . . . . . 27
To Change Volume Lock to the Cable Mode . . . . . . 27
To Change Volume Lock to the TV Mode. . . . . . . . . 27
To Change Volume Lock to the VCR Mode . . . . . . . 27
To Change Volume Lock to the Audio Mode . . . . . . 28
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Additional Information . . . . . . . . . . . . . . . . . . . . . . 30

Page 2

Millennium 4 Mnl M4092 rev

1/22/03

9:38 AM

INTRODUCTION
The Universal Electronics Millennium 4 is our latest
generation universal remote control. It is designed with
sophisticated technology that will allow you to finally
consolidate the clutter of all of the original remote controls
in your home entertainment system. Its packed with easyto-use features such as:
Preprogrammed to operate the cable converter
supplied by your cable system provider
Preprogrammed technology for easy setup
Convenient hide-away sliding door to conceal
less-used functions
Color-coded keys to quickly locate popular functions
Cable ID Lock to lock your remote control for use only
with the cable converter
Channel Lock to lock channel selection only to the
cable converter
Code library for video and audio components
Code Search to help program control of older or
discontinued components
Before you can use your new remote control, you will
need to program it to operate the specific home entertainment components you wish to control. Follow the
instructions detailed in this manual to set up your
Millennium 4 and enjoy your new remote control.

Page 3

Millennium 4 Mnl M4092 rev

1/22/03

9:38 AM

FEATURES AND FUNCTIONS


Use the illustration below to locate Millennium 4 features
and then study the Key Charts (on the next two pages) to
learn how they function.

Page 4

Millennium 4 Mnl M4092 rev

1/22/03

9:38 AM

Key Charts
The LED (red light) blinks to show that
the remote control is working and is
sending signals.
Press AUDIO, VCR, TV, or CBL once
to select a home entertainment
component to control.
Press POWER once to turn on or off
the selected home entertainment
component.
Use SETUP for all programming
sequences.
Use the keypad (0 ~ 9) to directly select
channels (e.g., 09 or 31).

Press MUTE once to turn sound off


or on.
Press ENTER once after entering channel
numbers on some TV models.
Use VOL+ (or VOL-) to raise (or lower)
the sound volume.
Use CH+ (or CH-) to select the next
higher (or lower) channel.
Press LAST once to recall the last channel
and to page back one screen in the
main menu.
Use FAV to cycle through your favorite
channels that are stored in your cable
converter.
Use GUIDE to display the program guide.
Press PPV/LOCK once to display the pay
per view menu or to lock out a specific
channel on your cable converter.
Use EXIT to exit out of your cable
converters menu and guide.
continued on next page...

Page 5

Millennium 4 Mnl M4092 rev

1/22/03

9:38 AM

FEATURES AND FUNCTIONS


Key Charts (continued)
Use cursor keys to move the cursor in
the program guide and menu screens.
Use SELECT/OK to choose options, PPV
events, and to tune programs from the
program guide.
Use INFO to display current channel and
program information.
Press MENU once to display your cable
converters screen menu.
Use PAGE (or PAGE ) to page up
or down) through menu screens and the
program guide.
Slide the door open to reveal less-often
used keys such as VCR transport buttons
and cable converter features.
In the VCR and TV modes, use the REW,
PLAY, FF, REC, STOP, and PAUSE keys to
control your VCR. To record a program,
press REC twice.
Reserved for cable converter features
(see your cable converter manual).
Press TV/VCR once to switch the VCR to
view TV channels or tape. This key will
also control the input select feature on
most TVs.

Page 6

Millennium 4 Mnl M4092 rev

1/22/03

9:38 AM

INSTALLING BATTERIES

1.

On the back of the Millennium 4, push the tab


and lift off the battery cover.

2.

Obtain two (2) fully-charged AA alkaline


batteries. Match the + and marks on the
batteries to the + and marks in the battery
case, then insert the new batteries.

3.

Press the battery cover back into place. The tab


should click when the cover is locked.

4.

Test the unit by pressing POWER and any mode


key (e.g. AUDIO, VCR, TV, or CBL). If the batteries
are inserted correctly, the LED will blink once.

NOTE: Whenever batteries need replacement, the Millennium 4


will blink twice with every key press. Simply replace the batteries
and the Millennium 4 will be restored to its full functionality,
complete with your favorite settings.

Page 7

Millennium 4 Mnl M4092 rev

1/22/03

9:38 AM

PROGRAMMING TV CONTROL
NOTE: If you own a TV/VCR combination, skip this section and
perform Programming TV/VCR Combo Control on page 16.

Locate the brand name of your TV in the Setup Codes


for TVs in the next section, and write it in the space below.
TV Brand: __________________________________
The brands are listed in alphabetical order with the most
popular codes listed first.You will use one of these codes
to program the Millennium 4 to operate your TV:
1.

Turn on the TV.

2.

On the Millennium 4, press TV once. Press and


hold SETUP until the LED blinks twice, then
release SETUP.

3.

Enter the first four-digit code for your TV. If


you perform this procedure correctly, the LED
will blink twice.
NOTE: If the LED did not blink twice after entering
the codes last digit, then repeat steps 2 through 3 and
try entering the same code again.

4.

Aim the Millennium 4 at your TV and press


POWER once. The TV should turn off. If it does
not, repeat steps 2 and 3, trying each code for
your brand until you find one that works. If it
still does not work, try searching for the code
(see Searching For Your Code on page 24).

5.

For future reference, write your TV code in the


boxes below.

NOTE: Remember, to use the Millennium 4 to operate your TV,


press TV first.

Setup Codes for TVs:


AOC
Admiral
Aiko
Akai
Alaron
America Action
Anam
Audiovox
Baysonic

0030, 0019
0093, 0463
0092
0030
0179
0180
0180
0451, 0180, 0623, 0092
0180

Page 8

Millennium 4 Mnl M4092 rev

Belcor
Bell & Howell
Bradford
Brockwood
Broksonic
CXC
Candle
Carnivale
Carver
Celebrity
Cineral
Citizen
Concerto
Contec
Craig
Crosley
Crown
Curtis Mathes
Daewoo
Daytron
Denon
Dumont
Electroband
Emerson
Envision
Fisher
Fujitsu
Funai
Futuretech
GE
Gibralter
GoldStar
Gradiente
Grunpy
Hallmark
Harley Davidson
Harman/Kardon
Harvard
Hitachi
Infinity
Inteq
JBL
JCB
JVC
KEC
KTV
Kenwood
Konka
LG

1/22/03

9:38 AM

0019
0154, 0016
0180
0019
0236, 0463
0180
0030, 0056
0030
0054
0000
0451, 0092
0060, 0030, 0056, 0092, 0280
0056
0180
0180
0054
0180
0047, 0747, 0054, 0154, 0051, 0451, 0093, 0060, 0030, 0056,
0145, 0016, 0166
0451, 0019, 0623, 0624, 0092
0019
0145
0017, 0019
0000
0154, 0236, 0463, 0180, 0178, 0179, 0019, 0623, 0624, 0282,
0280
0030
0154
0179, 0683
0180, 0179, 0171
0180
0047, 0747, 0051, 0451, 0093, 0178, 0021, 0282
0017, 0030, 0019
0030, 0178, 0056, 0019
0053, 0056
0180, 0179
0178
0179
0054
0180
0056, 0145, 0016
0054
0017
0054
0000
0053
0180
0180, 0030, 0280
0030, 0019
0707, 0628, 0632, 0638, 0703
0056
continued on next page...

Page 9

Millennium 4 Mnl M4092 rev

1/22/03

9:38 AM

PROGRAMMING TV CONTROL
Setup Codes for TVs (continued):
LXI
Logik
Luxman
MGA
MTC
Magnavox
Majestic
Marantz
Matsushita
Megatron
Memorex
Midland
Minutz
Mitsubishi
Motorola
Multitech
NAD
NEC
NTC
Nikko
Onwa
Optimus
Optonica
Orion
Panasonic
Penney
Philco
Philips
Pilot
Pioneer
Portland
Prism
Proscan
Proton
Pulsar
Quasar
RCA
RadioShack
Realistic
Runco
SSS
Sampo
Samsung
Sansei
Sansui
Sanyo
Scimitsu

0047, 0747, 0054, 0154, 0156, 0178


0016
0056
0150, 0030, 0178, 0019
0060, 0030, 0056, 0019
0054, 0030, 0179
0016
0054, 0030
0250
0178, 0145
0154, 0250, 0463, 0150, 0178, 0179, 0056, 0016
0047, 0747, 0017, 0051
0021
0093, 0150, 0178, 0019
0093
0180
0156, 0178, 0166
0030, 0056, 0019
0092
0030, 0178, 0092
0180
0154, 0250, 0166
0093, 0165
0236, 0463, 0179
0051, 0250
0047, 0747, 0156, 0051, 0060, 0030, 0178, 0021, 0056, 0019
0054, 0463, 0030, 0145, 0019
0054
0030, 0019
0166
0019, 0092
0051
0047, 0747
0178
0017, 0019
0051, 0250, 0165
0047, 0747, 0090, 0051, 0093, 0019, 0278
0047, 0747, 0154, 0180, 0030, 0178, 0056, 0019, 0165
0154, 0180, 0030, 0178, 0056, 0019, 0165
0017, 0030
0180, 0019
0030
0060, 0030, 0178, 0056, 0019
0451
0463
0154
0019

10

Page 10

Millennium 4 Mnl M4092 rev

Scotch
Scott
Sears
Semivox
Semp
Sharp
Shogun
Signature
Sony
Soundesign
Squareview
Starlite
Supreme
Sylvania
Symphonic
TMK
TNCi
Tandy
Technics
Technol Ace
Techwood
Teknika
Telefunken
Toshiba
Vector Research
Victor
Vidikron
Vidtech
Wards
White Westinghouse
Yamaha
Zenith

1/22/03

9:38 AM

0178
0236, 0180, 0178, 0179, 0019
0047, 0747, 0054, 0154, 0156, 0178, 0179, 0056, 0171
0180
0156
0093, 0688, 0165
0019
0016
0000
0180, 0178, 0179
0171
0180
0000
0054, 0030
0180, 0171
0178, 0056
0017
0093
0051, 0250
0179
0051, 0056
0054, 0180, 0150, 0060, 0179, 0056, 0019, 0016, 0092
0056
0154, 0156, 0060
0030
0053
0054
0178, 0019
0054, 0030, 0178, 0021, 0179, 0056, 0019, 0016, 0165
0463, 0623, 0624
0030, 0019
0017, 0463, 0624, 0016, 0092

11

Page 11

Millennium 4 Mnl M4092 rev

1/22/03

9:38 AM

PROGRAMMING VCR/DVD PLAYER CONTROL


NOTE: If you own a TV/VCR combination, skip this section and
perform Programming TV/VCR Combo Control on page 16.

Locate the brand name of your VCR in Setup Codes for


VCRs on the next page, or your DVD player in Setup Codes
for DVD Players on page 15, and write it in the appropriate
space below.
VCR Brand: ________________________________
or
DVD Player Brand: ____________________________
The brands are listed in alphabetical order with the most
popular codes listed first.You will use one of these codes
to program the Millennium 4 to operate your VCR or
DVD player:
1.

Turn on your VCR and insert a video cassette,


or turn on your DVD player and insert a DVD.

2.

On the Millennium 4, press VCR once. Press


and hold SETUP until the LED blinks twice,
then release SETUP.

3.

Enter the first four-digit code for your VCR or


DVD player. If you perform this procedure
correctly, the LED will blink twice.
NOTE: If the LED did not blink twice after entering
the codes last digit, then repeat steps 2 through 3 and
try entering the same code again.

4.

Aim the Millennium 4 at the VCR or DVD


player and press POWER once. The device
should turn off. If your VCR remote control
does not have a POWER key, press PLAY. If the
VCR does not respond, repeat steps 2 and 3,
trying each code listed for your brand until you
find one that works. If the device still does not
work , try searching for the code (see Searching
For Your Code on page 24).

5.

For future reference, write your devices code


and type in the boxes and space below.

Device Type:________________________
NOTE: Remember, to use the Millennium 4 to operate your VCR
or DVD player, press VCR first.

12

Page 12

Millennium 4 Mnl M4092 rev

1/22/03

9:38 AM

Setup Codes for VCRs:


Admiral
Adventura
Aiko
Aiwa
Akai
America Action
American High
Asha
Audiovox
Beaumark
Bell & Howell
Broksonic
CCE
Calix
Canon
Carver
Cineral
Citizen
Colt
Craig
Curtis Mathes
Cybernex
Daewoo
Denon
Dynatech
Electrohome
Electrophonic
Emerex
Emerson

0048, 0209
0000
0278
0037, 0000
0041
0278
0035
0240
0037
0240
0104
0184, 0121, 0209, 0002, 0479, 0295
0072, 0278
0037
0035
0081
0278
0037, 0278
0072
0037, 0047, 0240, 0072
0035, 0060, 0162, 0041
0240
0045, 0278, 0561
0042
0000
0037
0037
0032
0037, 0184, 0000, 0121, 0043, 0209, 0002, 0278, 0479, 0561,
0295, 0294
Fisher
0047, 0104
Fuji
0035, 0033
Funai
0000
GE
0035, 0060, 0048, 0240
Garrard
0000
Go Video
0432, 0526, 0643, 0232, 0279
GoldStar
0037
Gradiente
0000
HI-Q
0047
Harley Davidson
0000
Harman/Kardon
0081
Harwood
0072
Headquarter
0046
Hitachi
0000, 0042, 0041, 0105
Hughes Network Sys. 0042
JVC
0067, 0041
Jensen
0041
KEC
0037, 0278
KLH
0072
continued on next page...

13

Page 13

Millennium 4 Mnl M4092 rev

1/22/03

9:38 AM

PROGRAMMING VCR/DVD PLAYER CONTROL


Setup Codes for VCRs (continued):
Kenwood
Kodak
LXI
Lloyds
Logik
MEI
MGA
MGN Technology
MTC
Magnasonic
Magnavox
Magnin
Marantz
Marta
Matsushita
Memorex
Minolta
Mitsubishi
Motorola
Multitech
NEC
Nikko
Noblex
Olympus
Optimus
Orion
Panasonic
Penney
Pentax
Philco
Philips
Pilot
Pioneer
Polk Audio
Profitronic
Proscan
Protec
Pulsar
Quarter
Quartz
Quasar
RCA
RadioShack
Radix
Randex
Realistic

0067, 0041
0035, 0037
0037
0000
0072
0035
0240, 0043
0240
0000, 0240
0278
0035, 0039, 0081, 0000
0240
0035, 0081
0037
0035, 0162, 0454
0035, 0037, 0048, 0039, 0047, 0162, 0000, 0240, 0104, 0209,
0454, 0479, 0046
0042, 0105
0048, 0067, 0043
0035, 0048
0000, 0072
0067, 0104, 0041
0037
0240
0035
0037, 0048, 0162, 0104, 0454, 0432
0184, 0209, 0002, 0479, 0295
0035, 0225, 0162, 0454, 0616
0035, 0037, 0042, 0240
0042, 0105
0035, 0209, 0479
0035, 0081, 0618
0037
0067
0081
0240
0060
0072
0039
0046
0046
0035, 0162, 0454
0035, 0060, 0048, 0042, 0240, 0105, 0060
0000
0037
0037
0035, 0037, 0048, 0047, 0000, 0104, 0046

14

Page 14

Millennium 4 Mnl M4092 rev

ReplayTV
Runco
STS
Samsung
Samtron
Sanky
Sansui
Sanyo
Scott
Sears
Semp
Sharp
Shintom
Shogun
Singer
Sony
Sylvania
Symphonic
TMK
Tatung
Teac
Technics
Teknika
Thomas
Tivo
Toshiba
Totevision
Unitech
Vector
Video Concepts
Videosonic
Wards
White Westinghouse
XR-1000
Zenith

1/22/03

9:38 AM

0614, 0616
0039
0042
0045, 0240
0643
0048, 0039
0000, 0067, 0209, 0041, 0479
0047, 0240, 0104, 0046
0184, 0045, 0121, 0043
0035, 0037, 0047, 0000, 0042, 0104, 0046, 0105
0045
0048
0072
0240
0072
0035, 0032, 0000, 0636, 0033
0035, 0081, 0000, 0043
0000
0240
0041
0000, 0041
0035, 0162
0035, 0037, 0000
0000
0618, 0636
0045, 0043
0037, 0240
0240
0045
0045
0240
0035, 0060, 0048, 0047, 0081, 0000, 0042, 0240, 0072
0209, 0072, 0278
0035, 0000, 0072
0039, 0000, 0209, 0479, 0033

Setup Codes for DVD Players:


Aiwa
Apex
B&K
Denon
Fisher
GE
Gradiente
Harman/Kardon
Hitachi
Hiteker
JVC
Kenwood

0641
0672
0655, 0662
0490, 0634
0670
0522
0651
0582
0573, 0664
0672
0558, 0623
0534, 0682
continued on next page...

15

Page 15

Millennium 4 Mnl M4092 rev

1/22/03

9:38 AM

PROGRAMMING VCR/DVD PLAYER CONTROL


Setup Codes for DVD Players (continued):
Konka
Magnavox
Marantz
Mitsubishi
Onkyo
Optimus
Oritron
Panasonic
Philips
Pioneer
Proscan
RCA
Samsung
Sharp
Sherwood
Sony
Technics
Techwood
Theta Digital
Toshiba
Yamaha
Zenith

0711, 0719, 0720, 0721


0503, 0675
0539
0521
0503, 0627
0571
0651
0490, 0677, 0632, 0678, 0679
0503, 0539
0525, 0571, 0632
0522
0522, 0571
0573
0630
0633
0533
0490
0692
0571
0503
0490, 0545
0503, 0591

PROGRAMMING TV/VCR COMBO CONTROL


Locate the brand name of your TV/VCR Combo in Setup
Codes for TV/VCR Combos on the next page, and write it in
the space below.
TV/VCR Combo Brand: ________________________
The brands are listed in alphabetical order with popular
codes listed first.You will use one of these codes to program the Millennium 4 to operate your TV/VCR Combo:
1.

Turn on your TV/VCR Combo and insert a


video cassette.

2.

On the Millennium 4, press VCR once. Press


and hold SETUP until the LED blinks twice,
then release SETUP.

3.

Enter the first four-digit code for your TV/VCR


Combo. If you perform this procedure correctly,
the LED will blink twice.
16

Page 16

Millennium 4 Mnl M4092 rev

1/22/03

9:38 AM

NOTE: If the LED did not blink twice after entering


the codes last digit, then repeat steps 2 through 3 and
try entering the same code again.

4.

Aim the Millennium 4 at your TV/VCR Combo


and press POWER once. The unit should turn
off. If it does not respond, repeat steps 2 and 3,
trying each code listed for your brand until you
find one that works. If it still does not work, try
searching for the code (see Searching For Your
Code on page 24).

5.

If youve found a TV/VCR setup code that works


your TV/VCR Combo and a separate TV code is
also listed, youll need to program this code into
the Millennium 4 to access volume control (see
Programming TV Control on page 8).
If there is no separate TV code listed, you will
need to perform the following steps to access
volume control:
a. Press and hold SETUP until the LED blinks
twice, then release SETUP.
b. Enter 9 - 9 - 3. The LED will blink twice.
c. Press VCR once. The LED will blink twice.

6.

For future reference, write your TV/VCR


Combo code in the boxes below.

NOTE: Remember, to use the Millennium 4 to operate your


TV/VCR Combo, press VCR first.

Setup Codes for TV/VCR Combos:


American High
Brocksonic
Colt
Curtis Mathis
Daewoo
Emerson
Funai
GE
Hitachi
HQ
Lloyds
MGA
Magnavox

0035 (for TV use 0051)


0002, 0294,
0072
0035 (for TV use 0051)
0278
0002, 0294, 0479
0000
0035 (for TV use 0051), 0060 (for TV use 0047),
0048 (for TV use 0093), 0240
0035 (for TV use 0051), 0000
0000
0000
0240
0081 (for TV use 0054), 0035 (for TV use 0051), 0000
continued on next page...

17

Page 17

Millennium 4 Mnl M4092 rev

1/22/03

9:38 AM

PROGRAMMING TV/VCR COMBO CONTROL


Setup Codes for TV/VCR Combos (continued):
Magnin
Memorex
Mitsubishi
Orion
Panasonic
Penney
Quasar
RCA
Sansui
Sanyo
Sears
Sharp
Sony
Symphonic
Zenith

0240
0037, 0162 (for TV use 0250)
0048 (for TV use 0093)
0002, 0294, 0479
0035 (for TV use 0051), 0162 (for TV use 0250)
0035 (for TV use 0051), 0240, 0162 (for TV use 0250)
0035 (for TV use 0051), 0162 (for TV use 0250)
0060 (for TV use 0047), 0035 (for TV use 0051),
0048 (for TV use 0093)
0000, 0479
0240
0000, 0037
0048 (for TV use 0093)
0032 (for TV use 0000)
0000
0000

PROGRAMMING CABLE CONVERTER


(OR DBS RECEIVER) CONTROL
The Millennium 4 is preprogrammed at the factory to
operate the cable converter given to you by your cable
company. However, if you have another brand or model
of cable converter or satellite receiver that you would like
to control, then youll need to perform the following
instructions to unlock the cable key, enter in a new code,
and lock the cable key again.

To Unlock the CBL Key:


1.

Turn on the Cable Converter or DBS Receiver.

2.

On the Millennium 4, press CBL once. Press


and hold SETUP until the LED blinks twice,
then release SETUP.

3.

Enter 9 - 9 - 7. The LED will blink twice.

4.

Press CH- once. The LED will blink twice.

18

Page 18

Millennium 4 Mnl M4092 rev

1/22/03

9:38 AM

To Program the CBL Key:


1.

On the next page, locate the brand name of


your Cable Converter in Setup Codes For Cable
Converters, or DBS (Direct Broadcast Satellite)
Receiver in Setup Codes For DBS Receivers, and
write it in the appropriate space below.
Cable Converter Brand: ________________
or
DBS Receiver Brand: __________________
The brands are listed in alphabetical order
with the most popular codes listed first.You
will use one of these codes to reprogram the
Millennium 4 to operate your Cable Converter
or DBS Receiver.

2.

On the Millennium 4, press CBL once. Press


and hold SETUP until the LED blinks twice,
then release SETUP.

3.

Enter the first four-digit code for your Cable


Converter or DBS Receiver. If you perform this
procedure correctly, the LED will blink twice.
NOTE: If the LED did not blink twice after entering
the codes last digit, then repeat steps 2 through 3 and
try entering the same code again.

4.

Aim the Millennium 4 at your Cable Converter


or DBS Receiver and press POWER once. The
unit should turn off. If it does not respond,
repeat steps 2 and 3, trying each code listed for
your brand until you find one that works. If it
still does not work , try searching for the code
(see Searching For Your Code on page 24).

5.

For future reference, write your devices code


and type in the boxes and space below.

Device Type:________________________
NOTE: Remember, to use the Millennium 4 to operate your Cable
Converter or DBS Receiver, press CBL first.
continued on next page...

19

Page 19

Millennium 4 Mnl M4092 rev

1/22/03

9:38 AM

PROGRAMMING CABLE CONVERTER


(OR DBS RECEIVER) CONTROL
(continued)
To Lock the CBL Key:
1.

On the Millennium 4, press CBL once. Press


and hold SETUP until the LED blinks twice,
then release SETUP.

2.

Enter 9 - 9 - 7. The LED will blink twice.

3.

Press CH+ once. The LED will blink twice.

Setup Codes for Cable Converters:


ABC
Americast
Bell South
General Instrument
GoldStar
Hamlin
Jerrold
Memorex
Panasonic
Paragon
Philips
Pioneer
Pioneer
Pulsar
Quasar
Regal
Runco
Samsung
Scientific Atlanta
Starcom
Toshiba
Zenith

0003, 0008
0899
0899
0476
0144
0273
0003, 0476
0000
0000
0000
0305
0144, 0877, 0533
0533
0000
0000
0273
0000
0144
0008, 0477, 0877
0003
0000
0525, 0000, 0899

Setup Codes for DBS Receivers:


Echostar
0775, 1005
Expressvu
0775
GE
0566
General Instrument 0869, 0892
HTS
0775
Hughes Network Sys. 0749
JVC
0775
Mitsubishi
0749

20

Page 20

Millennium 4 Mnl M4092 rev

Next Level
Philips
Proscan
RCA
RadioShack
Samsung
Sony
Star Choice
Toshiba

1/22/03

9:38 AM

0869, 0892
0749, 1076
0392
0566, 0392
0869
1109
0639
0869
0749

PROGRAMMING CHANNEL CONTROL LOCK


By activating this feature, the Millennium 4 will only
allow access to the channel control capabilities of your
cable converter. This will guarantee that you do not
inadvertently change the channel on your TV or VCR.

To Activate Channel Control Lock:


1.

On the Millennium 4, press and hold SETUP


until the LED blinks twice, then release SETUP.

2.

Enter 9 - 9 - 6. The LED will blink twice.

3.

Press CH+ once. The LED will blink twice.

4.

Now, regardless of what mode you select (i.e.,


TV, VCR, or CBL), only the channel control capability of your cable converter will be accessible.
NOTE: This feature does not affect the Audio mode.

To De-Activate Channel Control Lock:


1.

On the Millennium 4, press and hold SETUP


until the LED blinks twice, then release SETUP.

2.

Enter 9 - 9 - 6. The LED will blink twice.

3.

Press CH- once. The LED will blink twice.

4.

The Millennium 4 will again provide TV and


VCR channel control capabilities while in the
TV or VCR mode.

21

Page 21

Millennium 4 Mnl M4092 rev

1/22/03

9:38 AM

PROGRAMMING AUDIO CONTROL


Locate the brand name of your audio amplifier or receiver
in one of the accompanying code lists at the end of this
section.Write it in the appropriate space below.
Audio Amplifier Brand: ________________________
or
Audio Receiver Brand:__________________________
The brands are listed in alphabetical order with popular
codes listed first.You will use one of these codes to
program the Millennium 4 to operate your audio device:
1.

Turn on the audio device.

2.

On the Millennium 4, press AUDIO once. Press


and hold SETUP until the LED blinks twice,
then release SETUP.

3.

Enter the first four-digit code for your audio


device. If you perform this procedure correctly,
the LED will blink twice.
NOTE: If the LED did not blink twice after entering
the codes last digit, then repeat steps 2 through 3 and
try entering the same code again.

4.

Aim the Millennium 4 at your audio device and


press POWER once. The unit should turn off. If
it does not respond, repeat steps 2 and 3, trying
each code listed for your brand until you find
one that works. If it still does not work , try
searching for the code (see Searching For Your
Code on page 24).

5.

For future reference, write your devices code


and type in the boxes and space below.

NOTE: Remember, to use the Millennium 4 to operate your audio


device, press AUDIO first.

Setup Codes for Audio Amplifiers:


Denon
GE
Harman/Kardon
JVC
Marantz

0160
0078
0892
0331
0892

22

Page 22

Millennium 4 Mnl M4092 rev

Optimus
Panasonic
Philips
Polk Audio
Realistic
Sony
Soundesign
Technics
Victor
Wards
Yamaha

1/22/03

9:38 AM

0395
0308
0892
0892
0395
0689
0078
0308
0331
0078
0354

Setup Codes for Audio Receivers:


ADC
Adcom
Aiwa
Capetronic
Carver
Casio
Clarinette
Denon
Garrard
Harman/Kardon
JBL
JVC
Kenwood
Lloyds
MCS
Magnavox
Marantz
Modulaire
Nakamichi
Onkyo
Optimus
Panasonic
Penney
Philips
Pioneer
Proscan
Quasar
RCA
Realistic
Sansui
Sharp
Sony
Soundesign
Sunfire
Teac
Technics

0531
0616
1405, 0121, 0405
0531
0008
0195
0195
1104, 1160
0463
0110, 0891
0110
0074
1313, 1027, 1570, 1569, 0186, 0077
0195
0039, 0346
0531, 0195, 0391
0039
0195
0097
0135
1023, 0531, 0670, 0186, 0177
1518, 0039
0195
1269, 1120, 0391
1023, 0531, 0014, 0150, 0630
1254
0039
1023, 1254, 0531, 0054, 0346
0195
0346
0186
1058
0670
1313
0463
1308, 1309, 1518, 0039
continued on next page...

23

Page 23

Millennium 4 Mnl M4092 rev

1/22/03

9:38 AM

PROGRAMMING AUDIO CONTROL


Setup Codes for Audio Amplifiers (continued):
Victor
Wards
Yamaha
Yorx
Zenith

0074
0014, 0054
0176, 1176, 0186
0195
0857

SEARCHING FOR YOUR CODE


If your TV,VCR or DVD Player, Cable Converter, or Audio
Component does not respond to the Millennium 4 after
trying all of the codes listed for your brand, or if your
brand is not listed at all, try searching for your code.
For example, to search for a code for your TV:
1.

Turn on your TV.

2.

On the Millennium 4, press and hold SETUP


until the LED blinks twice, then release SETUP.

3.

Enter 9 - 9 - 1. The LED will blink twice.

4.

Aim the remote control at the the TV and slowly


alternate between pressing POWER and TV.
Stop when the TV turns off.
NOTE: In the search mode, the Millennium 4 will
send IR codes from its library to the selected component, starting with the most popular code first.

5.

Press SETUP once to lock in the code.

6.

To search for the codes of your other


components, repeat steps 1 through 5, but
substitute the appropriate key (i.e., VCR, CBL,
or AUDIO) for the (VCR or DVD, Cable, or
Audio) component you are searching for.

24

Page 24

Millennium 4 Mnl M4092 rev

1/22/03

9:38 AM

CHECKING THE CODES


If you have set up the Millennium 4 using the Searching
For Your Code procedure, you may need to find out which
four-digit code is operating your equipment:
For example, to find out which code is operating your TV:
1.

Turn on your TV.

2.

On the Millennium 4, press and hold SETUP


until the LED blinks twice, then release SETUP.

3.

Enter 9 - 9 - 0. The LED will blink twice.

4.

To view the code for the first digit, press 1 once.


Wait 3 seconds and count the number of LED
blinks (e.g., 3 blinks = 3) and write down the
number in the leftmost TV Code box below.
NOTE: If a code digit is 0, the LED will not blink.

5.

Repeat step 4 three more times for remaining


digits. Use 2 for the second digit, 3 for the third
digit, and 4 for the fourth digit. Finish writing
down the code in the TV Code boxes below.

6.

To check for the codes of your other


components, repeat steps 1 through 5, but
substitute the appropriate key (i.e., VCR, CBL,
or AUDIO) for the (VCR or DVD, Cable, or
Audio) component you are checking.Write
down the codes in the appropriate boxes below.
TV Code

VCR (or DVD Player) Code

CBL Code

AUDIO ___________________ Code

25

Page 25

Millennium 4 Mnl M4092 rev

1/22/03

9:38 AM

RE-ASSIGNING DEVICE KEYS


The Millennium 4 can be set up to control a second TV
or VCR, or any combination of four home entertainment
components. For example, to have the Millennium 4
control a TV, a Cable Converter, and two VCRs, you will
need to re-assign the unused AUDIO key to operate the
second VCR as follows:
1.

On the Millennium 4, press and hold SETUP


until the LED blinks twice, then release SETUP.

2.

Enter 9 - 9 - 2. The LED will blink twice.

3.

Press VCR once, then press AUDIO once.

4.

The AUDIO key is now ready to be programmed


for your second VCR. See Programming
VCR/DVD Player Control on page 12.

To re-assign other device keys, repeat steps 1 through 4 by


substituting the key sequence from the following chart for
a desired component:
To Re-Assign

Perform Key Sequence

TV as 2nd VCR key:

SETUP - 9 - 9 - 2 - VCR - TV

TV as 2nd Audio key:

SETUP - 9 - 9 - 2 - AUDIO - TV

TV as 2nd Cable key:

SETUP - 9 - 9 - 2 - CBL - TV

TV back to TV:

SETUP - 9 - 9 - 2 - TV - TV

VCR as 2nd TV key:

SETUP - 9 - 9 - 2 - TV - VCR

VCR as 2nd Audio key: SETUP - 9 - 9 - 2 - AUDIO - VCR


VCR as 2nd Cable key: SETUP - 9 - 9 - 2 - CBL - VCR
VCR back to VCR:

SETUP - 9 - 9 - 2 - VCR - VCR

AUDIO as 2nd TV key: SETUP - 9 - 9 - 2 - TV - AUDIO


AUDIO as 2nd VCR key: SETUP - 9 - 9 - 2 - VCR - AUDIO
AUDIO as 2nd Cable key: SETUP - 9 - 9 - 2 - CBL - AUDIO
AUDIO back to AUDIO: SETUP - 9 - 9 - 2 - AUDIO - AUDIO
Upon completion of a re-assignment, the LED will blink
twice to confirm your selection.At that time, you will also
need to program the Millennium 4 to control the new
component. See previous sections on Programming TV
Control, Programming VCR/DVD Player Control,
Programming Cable Converter (or DBS Receiver) Control,
or Programming Audio Control.
26

Page 26

Millennium 4 Mnl M4092 rev

1/22/03

9:38 AM

CHANGING VOLUME LOCK


The Millennium 4 is set to control volume of a component
through your TV while in the TV,VCR, or Cable mode.
However, in the Audio mode, you have separate control of
of your audio components volume.
If your TV is not remote controllable, or if you would like
the volume to be controlled by a different component, you
can change the Volume Lock setting to control a volume
through a non-associated mode (e.g., through the cable in
the TV mode).

To Change Volume Lock to the Cable Mode:


1.

On the Millennium 4, press and hold SETUP


until the LED blinks twice, then release SETUP.

2.

Enter 9 - 9 - 3 and then press CBL once. The


LED will blink twice.

3.

Now, whenever you press VOL+, VOL-, or MUTE


on the Millennium 4, volume will be controlled
by your cable converter or DBS receiver.

To Change Volume Lock to the TV Mode:


1.

On the Millennium 4, press and hold SETUP


until the LED blinks twice, then release SETUP.

2.

Enter 9 - 9 - 3 and then press TV once. The


LED will blink twice.

3.

Now, whenever you press VOL+, VOL-, or MUTE


on the Millennium 4, volume will be controlled
by your TV.

To Change Volume Lock to the VCR Mode:


1.

On the Millennium 4, press and hold SETUP


until the LED blinks twice, then release SETUP.

2.

Enter 9 - 9 - 3 and then press VCR once. The


LED will blink twice.

3.

Now, whenever you press press VOL+, VOL-, or


MUTE on the Millennium 4, volume will be
controlled by your VCR or DVD player.
continued on next page...

27

Page 27

Millennium 4 Mnl M4092 rev

1/22/03

9:38 AM

CHANGING VOLUME LOCK ( continued)


To Change Volume Lock to the Audio Mode:
NOTE: Performing these steps will allow you to access the volume
control of your audio component in all modes.

1.

On the Millennium 4, press and hold SETUP


until the LED blinks twice, then release SETUP.

2.

Enter 9 - 9 - 3 and then press AUDIO once. The


LED will blink twice.

3.

Now, whenever you press press VOL+, VOL-, or


MUTE on the Millennium 4, volume will be
controlled by your audio component.

28

Page 28

Millennium 4 Mnl M4092 rev

1/22/03

9:38 AM

TROUBLESHOOTING
PROBLEM:

LED does not blink when you press a key.

SOLUTION: Replace the batteries with two (2) new AA


alkaline batteries (see page 7).
PROBLEM:

LED blinks when you press a key, but home


entertainment component does not respond.

SOLUTION: Make sure you are aiming the Millennium 4 at


your home entertainment component and that
you are within 15 feet of the component you are
trying to control.
PROBLEM:

The Millennium 4 does not control home


entertainment components or commands are
not performing properly.

SOLUTION: Try all listed codes for the component brand


being set up. Make sure all components can be
operated with an infrared remote control.
PROBLEM:

TV/VCR combo does not respond properly.

SOLUTION: Use the VCR codes for your brand. Some combo
units may require both a TV code and a VCR
code for full operation (see page 16).
PROBLEM:

No volume on a second TV.

SOLUTION: Follow instructions in Changing Volume Lock


(see page 27).
PROBLEM:

CH+ , CH - , and LAST do not work for your


RCA TV.

SOLUTION: Due to RCA design (1983-1987), only the original


remote control will operate these functions.
PROBLEM:

Changing channels does not work properly.

SOLUTION: If original remote control required pressing


ENTER to change channels, press ENTER on the
Millennium 4 after entering a channel number.
PROBLEM:

Tried Search Method and still could not find a


working code.

SOLUTION: Try the Search Method again after clearing out


the device key as follows: Press and hold SETUP
until the LED (red light) blinks twice, then
release. Next enter 9 - 9 - 2. Then press and
release the device key to be cleared twice.
PROBLEM:

Remote control does not turn on Sony or Sharp


TV/VCR Combo.

SOLUTION: For power on, these products require programming TV codes on the Millennium 4. For Sony,
use TV code 0000 and VCR code 0032. For Sharp,
use TV code 0093 and VCR code 0048.

29

Page 29

Millennium 4 Mnl M4092 rev

1/22/03

9:38 AM

ADDITIONAL INFORMATION
The Millennium 4 does not have any user-serviceable
parts. Opening the case, except for the battery cover, may
cause permanent damage to your Millennium 4.
For help via the Internet, visit us at:
cable.rcinfo.com
(do not type in http:// or www before the address)
For help via e-mail, contact us at:
CableHelp@ueic.com
Copyright 2003 by Universal Electronics Inc. No part
of this publication may be reproduced, transmitted,
transcribed, stored in any retrieval system, or translated
to any language, in any form or by any means, electronic,
mechanical, magnetic, optical, manual, or otherwise,
without the prior written permission of Universal
Electronics Inc.
M4092A

01/03

30

Page 30

Millennium 4 Mnl M4092 rev

1/22/03

9:38 AM

Page 31

Millennium 4 Mnl M4092 rev

1/22/03

9:38 AM

Page 32

You might also like