Professional Documents
Culture Documents
Contractor
Job Location
Approval
Engineer
Approval
Representative
Series LC-150
Features
Durable brass bodied control valve for years of service
WQA Certified fully automatic metered demand control valve
S
ophisticated digital electronic controls that store operating
history that can be accessed by the user
Fully adjustable regeneration cycles
Dry contact lock out switch for remote interface is standard
WQA Certified high capacity resin
H
ighly corrosion resistant WQA or NSF Certified fiberglass
tanks
Durable polypropylene lower distribution system
Standards
Control Valve- WQA Certified to NSF/ANSI Std. 61 and ANNEX "G"
Ion Exchange Resin- WQA Certified to NSF/ANSI Std. 61
Mineral Tank- WQA or NSF Certified to NSF/ANSI Std. 44 or 61
Series LC-150
Specifications
A Series LC-150 water softening system shall be installed on
the buildings main water line just after it enters the building.
The installation point shall be after any backflow prevention
or pressure regulating valves. Other installation options are to
install a system just before the water heater or other types of
equipment needing the protection of softened water. In installations where dedicated cold water make up to a water heater
is the installation point, a backflow preventer and a thermal
expansion tank must be installed as well. The system shall be
installed with a bypass valve to allow for the shut down and
removal of the unit without interrupting the water supply to the
building.
The water softener shall be a down flow regenerated, metered
demand, sodium cycle cation exchange type system with all
components necessary for proper operation. Electrical requirements are 120 volt 60 hertz. A local drain is required to accept
drain water from the system. The feed water pressure must not
fall below 25psi or exceed 125psi. Water temperature must not
fall below 34F or exceed 110F (1 - 43C).
The system shall provide softened water measuring less than
one grain per gallon of hardness as Calcium Carbonate when
operated within the manufacturers operational specifications.
! WARNING
Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after
the system.
Watts product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements,
please contact Watts Technical Service. Watts reserves the right to change or modify product design, construction, specifications, or materials without prior notice and without incurring any obligation to make such changes and modifications on Watts products previously or subsequently sold.
Dimensions - Weights
DD
EE
Hardness (maximum) . . . . . . .
Water Pressure . . . . . . . . . . .
Depends on customers
acceptable hardness leakage
level.
2
5psi to 125psi
(171 kPa to 8.5 bar)
FF
BB
AA
NOTICE
FRONT
SIDE
FRONT
SIDE
Model No.
Dimensions
A
M4210B-285NT
M4214B-285NT
M4218B-285NT
M4222B-285NT
M4226B-285NT
M4230B-285NT
WEIGHTS
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
in.
mm
547/8
6615/16
663/8
68
70
763/8
1394
1699
1686
1727
1778
1940
553/4
677/8
671/4
69
71
771/4
1416
1724
1708
1753
1803
1962
61
733/8
723/4
747/16
767/16
823/4
1549
1864
1848
1890
1941
2102
1315/16
1415/16
1515/16
181/8
211/8
241/8
353
378
405
460
536
613
19
1913/16
2013/16
2113/16
235/16
2413/16
483
503
528
554
592
630
18
18
18
24
24
30
457
457
457
610
610
762
40
40
40
41
50
50
1016
1016
1016
1041
1270
1270
210
240
320
380
585
710
95
109
145
173
266
323
Specifications
Model No.
M4210B-285NT
M4214B-285NT
M4218B-285NT
M4222B-285NT
M4226B-285NT
M4230B-285NT
TANK
SIZE
Mineral Tank
RESIN
GRAVEL
Ft3
12" x 52"
14" x 65"
16" x 65"
18" x 65"
21" x 62"
24" x 72"
2.0
3.0
4.0
5.0
7.0
10.0
30 lbs.
60 lbs.
80 lbs.
100 lbs.
100 lbs.
200 lbs.
Brine Tank
TANK
SALT
size
fill
18x40
18x40
18x40
24x41
24x50
30x50
400
400
400
600
800
1400
Softening
CAPACITY
Max
min
60 K
90 K
120 K
150 K
210 K
300 K
40 K
60 K
80 K
100 K
140 K
200 K
30
45
60
75
105
150
12
18
24
30
42
60
15/20
17/22
25/40
30/50
35/53
40/55
15/25
15/25
15/25
15/25
15/25
15/25
3.5
5.0
7.0
11.0
13.0
15.0
Ordering Information
Model No.
M4210B-285NT
M4214B-285NT
M4218B-285NT
M4222B-285NT
M4226B-285NT
M4230B-285NT
DESCRIPTION
PIPE SIZE
SPACE
REQUIRED
DxWxh
1.5"
1.5"
1.5"
1.5"
1.5"
1.5"
WEIGHT
LBS
KGS
210
240
320
380
585
710
95
109
145
173
266
323
NOTICE
Capacities are based on resin manufacturers data and are dependent upon influent water TDS, temperature, bed depth, and flow
rates. Feed water must be free of oil and color. Pipe size, tank size, and space requirements are in inches. Flow rates listed at 25
psi drops are for intermittent peak flow rates and are not to be used as continuous flows.
ES-WQ-LC-150 1441
2014 Watts