SKF TMJG 100D has been specially designed to accurately measure the hydraulic pressure when mounting bearings with the SKF Drive-up program. Uses the principle of a piezo-electric element which generates a pressure related voltage. This signal is converted by the electronics of the instrument into a digital read out. The unit is equipped with a special peak function for the possibility of measuring very sudden pressure peaks.
SKF TMJG 100D has been specially designed to accurately measure the hydraulic pressure when mounting bearings with the SKF Drive-up program. Uses the principle of a piezo-electric element which generates a pressure related voltage. This signal is converted by the electronics of the instrument into a digital read out. The unit is equipped with a special peak function for the possibility of measuring very sudden pressure peaks.
SKF TMJG 100D has been specially designed to accurately measure the hydraulic pressure when mounting bearings with the SKF Drive-up program. Uses the principle of a piezo-electric element which generates a pressure related voltage. This signal is converted by the electronics of the instrument into a digital read out. The unit is equipped with a special peak function for the possibility of measuring very sudden pressure peaks.
Instructions for use 1. Application The high precision digital gauge TMJG 100D has been specially designed to accurately measure the hydraulic pressure when mounting bearings with the SKF Drive-up program. The gauge is also suitable for other applications where the pressure has to be determined with a high accuracy up to pressures of 100 MPa. 2. Description The TMJG 100D uses the principle of a piezo-electric element which generates a pressure related voltage. This signal is converted by the electronics of the instrument into a digital read out. The unit is equipped with a special peak function for the possibility of measuring very sudden pressure peaks. It fits the SKF pumps 729124, TMJL 50 and TMJL 100 but can also be connected directly to an SKF hydraulic nut type HMV. 3. Technical data Connection thread : G 1/4 Measuring range : 0-100 MPa Resolution : 0,1 MPa Accuracy : 0 - 70 MPa 0,14 MPa 70 - 100 MPa 0,50 MPa Response time : 99% in 0,001 s Sensor : Piezo-electric element Operating temperature : 10-50C (50-122F) Functions : ON/OFF with automatic switch off after 10 minutes PEAK for indication of sudden pressure peaks Battery type : 9 V IEC 6LR61 Battery life : 100 hours (continuous operation) 2 SKF TMJG 100D 4. Operating instructions 1. Screw the gauge into the pressure port. 2. Adjust the face of the gauge to the preferred position by loosening the counter-nut (fig. 1) between the housing and the shaft. 3. Turn the dial of the gauge to the preferred position (fig.2). The dial can be rotated over 355. 4. Switch the unit ON by pressing the ON/OFF button. 5. The unit is switched off by pressing the ON/OFF button once more or automatically after 10 minutes of use. Figure 1 Figure 2 SKF TMJG 100D 3 6. To facilitate measurements of sudden pressure peaks the units is supplied with a special PEAK function. The exact function of the PEAK function is explained in fig. 3. The PEAK function is confirmed on the display. Note 1. Due to internal signal noise the peak reading at zero pressure will be around 2 MPa. 2. If the maximum pressure of 100 MPa exceeded the figure 1 will be shown on the left hand side of the display. WARNING! For safety reasons never apply pressures above 100 MPa. 5. Maintenance Replace the battery as soon as Battery low is displayed on the gauge. The instrument is then opened by simply turning the dial face beyond the limit stop. 6. Accessories Designation Description TMJG S76 Rubber protection sleeve M P 5 3 7 E In line with our policy of continuous development of our products we reserve the right to alter any part of the above specification without prior notice. Although care has been taken to ensure the accuracy of this publication, SKF does not assume any liability for errors or omissions. SKF Maintenance Products Copyright SKF 2001/08 www.mapro.skf.com Display digitally frozen (Hold) Display: highest value drops with 2 digits/sec. = 20 digits = 20 digits = 20 digits Switch point Pressure profile (Display in Normal Operation) Switch Point Display value in the PEAK-mode Figure 3