You are on page 1of 19

Figure 1.

To make this object, notice the absolute coordinate location of the smaller
circle (4,4.5) which is where you are going to start with. nd the rest of the object
follows with it.
Figure !. This object is made with the ad"antage of the direct distance entry
command to first make the #erimeter (first without the cur"es). The cur"es in the
sides can be made by using the fillet or circle-ttr command then trim.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Figure $. gain notice the absolute coordinate location of the line in 1, $ and the
#oint in 5,% which is where the rest of the drawing follows.
Figure 4. This object again has absolute coordinates to follow. This is made through
circles-2P, lines, and ars (start&center&radius).
Figure 5. To make this object, start with the line, then the arcs. The center of the
arc in 45' is the end#oint of the location 1.5(.
Figure ). This drawing again has absolute coordinate locations to follow. The
triangle is made by following those commands gi"en in numbered order. To circle
inside the triangle is made through cicle-ttr command.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Figure %. Though this object can be made through lines and arcs, the objecti"e is to
make this one using #olylines wherein the lines and arcs are connected.
Figure *. This object starts with the smaller circles with the diameter or (.5( and
the rest follows. circle-ttr command is more useful than using arc to make the
cur"es.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Figure +. This object is almost similar to figure + which also starts with the smaller
circles. gain a cicle-ttr command is used here than arcs to make the cur"es. To
co#y the arc inside or outside at a different radius, the offset command could be
useful.
Figure 1(. ,n this objects the direct distance entry could be useful to make the
#erimeter. For the cur"es on the edge, fillet command could also be used. -elati"e
rectangular entry with snap-from command could locate the circles. center. To
make the dash&dot center line you need to load the line in the linetype bo/.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
Figure 11. The objecti"e of making this object is to learn the array (rectangular and
#olar) command. There are a total of 1%) smaller circles. There are 4( circles
around each inner circles and +) circles inside.
Figure 1!. This e/ercise will hel# you use the chamfer command which will hel#
you make the cut on the edge. The mirror command is also used to reflect an
object to its o##osite side.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
.
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net
www.jntuworld.com
www.jntuworld.com
www.jwjobs.net

You might also like