Professional Documents
Culture Documents
Since 1983
VIDEO
Control functions are provided through RS-232 and RS-485 circuits that are connected to a dedicated
computer at a remote location. Connectors provided on the camera control unit allow for local control via
a laptop computer communicating through the RS-232 port.
During normal (unattended) operations, the remote computer communicates through the REMOTE
connector on the rear panel of the controller assembly. If intervention becomes necessary at the camera
site, a laptop computer communicating through the LOCAL connector on the front panel of the controller
assembly may be used. Internal circuits in the controller assembly monitor for the presence of data on the
LOCAL port. When data is detected, an internal relay automatically switches control from the REMOTE port
to the LOCAL port. Time delay circuits keep the relay latched in local control mode for a predetermined
(adjustable) period of time. When no further local data is detected after the time delay, the internal relay
automatically defaults to the REMOTE port, thus resuming normal (unattended) operations.
Visual indicators (light emitting diodes, or LEDs) have been provided on the front panel for verification
of operational status. The CAMERA ON indicator illuminates when 24 VAC power is available to the video
camera. The SYSTEM ON indicator illuminates when power is applied to the controller assembly. The
LOCAL ON indicator illuminates whenever local computer control is applied.
A number of filters and surge protectors are provided within the camera control assembly for protection
of power, data and video circuits. Main AC input power is applied through a power entry module
incorporating supplementary overcurrent protection (fuse), an ON-OFF switch and EMI filtering. A number
of surge protectors have been incorporated to protect the camera control unit from overvoltage surges
that may originate from outside sources. These surge protectors are connected in the video and camera
data circuits.
Efficiency Better than 90% over line voltage range, at full load
Camera Fuse
(4A)
Camera Power
Switch
Status Lights Video Out
-Camera On (Red) (BNC Fitting)
-System On (Amber) Local Camera Control
-Local On (Green) (DB9 Receptacle)
Video Out
(BNC Fitting)
Video In
(BNC Fitting)
Various sizes and configurations to meet all of your traffic industry needs.
Rainproof, weatherproof housing.
Ground, pole, or pedestal mountable options.
3 Point Corbin locking system.
EMI / RFI Protection system.
Natural or forced convection optionss for
fo
or equipment ventilation.
Removable air filters cover louvers to
o minimize
m dust and dirt intrusion.
Corrosion resistant aluminum.
Upgrade to a
new Multilink
TCC today!
W
D
Main Body .125 Aluminum with Door Front and Rear Doors
Synthetic Rubber Seal with 3-Point Corbin
Hardware Stainless Steel Lock
Cable Entrance Cable Entry Locations In
Finish Polyester Powder Coat
Bottom Of Enclosure
Battery Storage Optional Battery
Storage Unit Heating and Cooling Forced Convection with
BSU-3/4 Installed Cooling Fan
BSU-6/8
Finish Polyester Powder Coat Heating and Cooling Natural Convection with
Fan Option
Brown
Green
Hunter Green
Gray
Almond
47
4 7.596
5 48.125
45
5.5
.513
24.4
.409
409 20.600
0
12.000 23.2
23 .253
53
27.7
27 7883
3
12.000 15.000
6.000
15.000
Finding the right Traffic control cabinet to meet your physical specifications is made simple with the Multilink Build a
Cabinet Program™.
How does the Multilink Build a Cabinet Program™ work? Simply tell us the physical sizes, features, and quality that you
need for your specific applications and we will produce you an E-Drawing for your review prior to start of production.
Capable of quick,
custom service
for all your
manufacturing
needs
Cabinet
securing clips
are available
Product Information
Stock ID: 017-054-20 017-054-21 017-054-22 017-054-23
Input Voltage 120VAC 240VAC 120VAC 240VAC
Input Current 15.5A 8A 7.5A 3.9A
Input Frequency 60Hz 60Hz
Line Accept 102VAC 204VAC 102VAC 204VAC
Line Reject 90VAC 180VAC 90VAC 180VAC
Output Voltage 120VAC -5%/+2% 120VAC -5%/+2%
Output Current 11.25A 5.4A
Output Power 1350VA 650VA
Efficiency 90% typical 90% typical
Battery Voltage 48VDC nominal 24VDC nominal
Low Battery
42.0VDC 21.0VDC
Cutoff
Battery
No higher than 49VDC No higher than 24.5VDC
Acceptance
Battery Charger Bulk, balance, and float Bulk, balance, and float
Recharge Current 10A max 10A max
Battery Float
54.7VDC (2.28V/cell) 27.36VDC (2.28V/cell)
Voltage
Charger
-0.09V/degC -0.09V/degC
Temperature
-0.05V/decF -0.05V/decF
Compensation
Transfer Time 4mS typical 4mS typical
Size 19”W x 8.6”H x 12.5D 19”W x 8.6”H x 12.5D
(483mm x 218mm x 318mm) (483mm x 218mm x 318mm)
POWER SOLUTIONS
Black Hawk
Status at a glance with
Resettable output user friendly LCD display
8 Programmable dry
circuit breaker relay contacts with
RS232
User-friendly LCD display shows history, battery test, major alarm, event counter and many
POWER SOLUTIONS
Black Hawk
Modern PCB
Assembly Process Air Flow Cooling Duct
Black Hawk Inverter
! )NRUSH
(Z
#URRENT -AY
p(Z 4RIP "REAKER
4HERMISTER
,INE 3ENSE )SOLATION 2ELAY
6 -/6 0ROTECTION
-UST
p
$ISCONNECT FOR
)NVERTER
&ERRO
.O )SOLATION 4RANSFERS ON
,ITTLE 4RANSIENTS AND
0ROTECTION .OISE
/UTPUT IS
3OMETIMES
)NTERRUPTED
/PTION AT
!DDED #OST -UST #ONNECT
FOR )NVERTER
2ISK /UTAGE TO
#OMPLEX 4EST "ATTERY &ANS
)NVERTER )NVERTER
#ONTROLLER 2EQUIRED
#OLD 3TART
)NVERTER
Product Information
Stock ID: 017-055-20 017-055-21
POWER SOLUTIONS
MP Plus
Status at a glance with
user friendly LCD display
Front loaded duplex
receptacle
No transfer, No interruption
RS485
Universal Input
120V operation
POWER SOLUTIONS
MP Plus
3IMULTANEOUS
4RUE
)NVERTER /PERATION
503
.O 3WITCHING
&ULL ! #HARGER
AT ALL ,OADS /UTPUT
3TATUS "ATTERY #HARGER
-ONITORING
)NTERFACE
.O 2ISK "ATTERY
3TANDARD
)NVERTER 4EST
&EATURE
.O #OOLING
3IMPLIFIED ,OW 6OLTAGE ,OW 6OLTAGE &AN 2EQUIRED
#ONTROLLER "OOST )NVERTER
POWER SOLUTIONS
FlexPOWER 25
Features & Benefits
tWall-mount or pole-mount 12-volt DC
uninterruptible power system
tUnobtrusive, aesthetically pleasing enclosure
tOptional battery heater extends battery life and
run-time in cold locations
tLocal alarm indicators and remote status monitoring
and reporting
tWide-range power input capability accepts nearly any AC
voltage/frequency combination
tProduct is RoHS compliant
t NRTL compliance to UL/CSA 60950, EN 60950 and FCC Part 15,
Class B
Input Voltage 90 to 265 VAC Input Protection Replaceable fuse rated at 1-ampere
Replaceable metal oxide varistors (MOVs)
at input
Input Frequency 47 to 63Hz Output Protection Current limit and overvoltage shutdown;
fused battery
Power Factor 0.9 or better at any Operating -40°F to 149°F (-40°C to 65°C)
load Temperature
Output Power 25 VA Storage -58°F to 158°F (-50°C to 70°C)
Temperature
Output Voltage 12 VDC (adjustable) Humidity 0 to 95% non-condensing
(nominal)
Voltage Adjustment 9 to 16 VDC Alarms LED battery Status / Alarm
Range
Output Current 2 amps DC Battery 7.2 amp-hour maintenance-free VRLA
(nominal) battery
Output Ripple Less than 25mV RMS Output Noise Less than 1.8 volts peak-to-peak
(voice band)
POWER SOLUTIONS
FlexPOWER 50
Features & Benefits
tWall-mount or pole-mount 48-volt DC uninterruptible power
system
tUnobtrusive, aesthetically pleasing enclosure
tOptional battery heater extends battery life and run-time in
cold locations
tLocal alarm indicators and remote status monitoring and
reporting
tWide-range power input capability accepts nearly any AC
voltage/frequency combination
tProduct is RoHS compliant
tNRTL compliance to UL/CSA 60950, EN 60950 and FCC Part 15,
Class B
Input Voltage 90 to 265 VAC Input Protection Replaceable fuse rated at 1-ampere
Replaceable metal oxide varistors (MOVs)
at input
Input Frequency 47 to 63Hz Output Protection Current limit and overvoltage shutdown;
fused battery
Power Factor 0.9 or better at any load Operating -40°F to 149°F (-40°C to 65°C)
Temperature
Output Power 50 VA Storage -58°F to 158°F (-50°C to 70°C)
Temperature
Output Voltage 48 VDC (adjustable) Humidity 0 to 95% non-condensing
(nominal)
Voltage Adjustment 42 to 58 VDC Alarms LED battery Status / Alarm
Range
Output Current 1 amp DC Battery Four 7.2 amp-hour maintenance-free
(nominal) VRLA batteries
Output Ripple Less than 25mV RMS Output Noise Less than 1.8 volts peak-to-peak
(voice band)
POWER SOLUTIONS
FlexPOWER 150 and 300
Features & Benefits
tPrimary power conversion for 48-volt DC UPS
applications
tProvides equipment operating power with
simultaneous battery charging capability
tTemperature compensating charging for long
battery life and optimum standby time
tLocal LCD display and remote status monitoring
and reporting
tWide-range power input capability accepts nearly
any AC voltage/frequency combination
tProduct is RoHS compliant
tNRTL compliance to UL/CSA 60950, EN 60950 and
FCC Part 15, Class B
The FlexPOWER Model 150 and 300 power conversion FlexPower 150
modules provide nominal 48-volt DC output using Stock ID 017-058-20
Description 48VDC, 150 Watt Power Module
commercial AC line as the input power source. Output DC Dimensions N/A
is used to power MDU, MTU and SBU applications while Weight N/A
maintaining a standby battery in a state of full charge. This UOM Each
product is designed for use in the FlexPOWER Enclosure
that enables construction of larger capacity semi- FlexPower 300
customized power systems serving telecommunications, Stock ID 017-059-20
data and video services. Either four or eight standby Description 48VDC, 300 Watt Power Module
batteries may be used with this power module, providing Dimensions N/A
Weight N/A
either 7.2 or 14.4 ampere-hour standby capability. UOM Each
POWER SOLUTIONS
FlexPOWER ENCLOSURES
Features & Benefits
tPrimary power conversion for 48-volt DC UPS applications.
tProvides equipment operating power with simultaneous battery charging
capability.
tTemperature compensating charging for long battery life and optimum
standby time.
tLocal LCD display and remote status monitoring and reporting.
tWide-range power input capability accepts nearly any AC voltage/
frequency combination
tProduct is RoHS compliant
tNRTL compliance to UL/CSA 60950, EN 60950 and FCC Part 15, Class B
Input Voltage 90 to 265 VAC Input Protection External fuse or circuit breaker required
Replaceable metal oxide varistors
(MOVs) at input
Input Frequency 47 to 63Hz Output Protection Current limit and overvoltage
shutdown
Power Factor 0.9 or better at any load Operating -40°F to 149°F (-40°C to 65°C)
Temperature
Output Power 150 VA Storage -58°F to 158°F (-50°C to 70°C)
Temperature
Output Voltage 48 VDC (adjustable Humidity 0 to 95% non-condensing
(nominal)
Voltage Adjustment 42 to 58 VDC Local Status & Built-in LCD display for operating
Range Alarms parameters
and alarms
Output Current 3.1 amp DC Battery Supports (4) or (8) 7.2 amp-hour
(nominal) maintenance-free VRLA batteries
Output Ripple Less than 3mV RMS Output Noise Less than 90mV peak-to-peak
(voice band)
POWER SOLUTIONS
FlexPOWER BATTERIES
032-030-10
Stock ID 032-030-10
Description 12 Volt, 7.2 amp-hour VRLA battery
Dimensions 5.95” x 2.54” x 3.70” (151mm x 65mm x 94mm)
Weight 5.45 lbs. (2.47 Kg)
UOM Each
032-032-10
Stock ID 032-032-10
Description 12 Volt, 12 amp-hour VRLA battery
Dimensions 5.95” x 3.86” x 3.94” (151mm x 98mm x 100mm)
Weight 8.36 lbs. (3.80 Kg)
UOM Each
032-033-10
Stock ID 032-033-10
Description 12 Volt, 17 amp-hour VRLA battery
Dimensions 7.13” x 2.99” x 6.58” (181mm x 76mm x 167mm)
Weight 14.34 lbs. (6.50 Kg)
UOM Each
The FlexPOWER series of batteries complements the FlexPOWER product line of DC power systems and power
conversion modules. These batteries are lead-acid, maintenance-free units suitable for use inside enclosures typically
applied in customer premise locations in MDU, SBU and similar applications. Batteries may be used singly in 12-volt
backup systems or in series or series-parallel arrangements in 48-volt DC systems.
Features & Benefits
tDesigned for standby, float service application
tRecognized component per UL standards for standby batteries
POWER SOLUTIONS
Longhaul / Backhaul Systems
Multilink’s Longhaul/Backhaul Systems provide uninterrupible electrical power for Mission Critical Network Devices
DC Distribution
Features & Benefits
t24 and 48VDC
tOptional Low Voltage Disconnect
tConfigurable for 10 to 100A Loads
t19” Rack Mount, 2RU Height (optional 23” Spacing)
tETL Certification
Uninterruptible Power
Supply
Features & Benefits
tTrue UPS Power Supply
TM
Contact Multilink Technical Support to select the best Integrated UPS System for your application
TM
# Cable Strain
Dome Size Splice Tray # Splice # Ground
Mounting Relief Kits
(Max. Splices) (# splices) Trays Lugs
( g size )
4024-D P = Pole/Wall
612-SSTP 3-6
4024 (48 Single A X 1-4 X A = Aerial X X 0-5 *
12 Splices (3/4" Fitting)
fusion) D = ADSS
4048-D P = Pole/Wall
4048-SSTP 3-6
4048 (96 Single B X 1-4 X A = Aerial X X 0-5 *
24 Splices (3/4" Fitting)
Fiber fusion) D = ADSS
Optic
Closure 4000-D
4048-SSTP
(192 Single B
24 Splices P = Pole/Wall
fusion) 3-6
4000 X 1-8 X A = Aerial X X 0-6*
4000-D (1" Fitting)
4072-SSTP D = ADSS
(288 Single C
36 Splices
fusion)
*See notes
Example
SFOC4024-A-1-A-3-1
The Multilink Starfighter 4024-D Fiber Optic Dome Splice closure is an “all parts” inclusive hermetically sealed splice
enclosure designed for ease of assembly and re-entry. The closure is designed with a gasketed split end plate for
midaccess cable applications and an easy to install “no special tool” sealing system. All major hardware is factory installed
to allow for quick field installation. Universal Multicentric* Grommets along with compression style lateral or branch
cable seals, makes installing the enclosure easy. The 4024-D is a small capacity closure that can be used in aerial, pedestal,
and underground applications.
*Multicentric is a Registered Trademark of Mar-Don
A-B C-D E F G H
enclosure designed for ease of assembly and re-entry. The closure is designed with a gasketed split end plate for mid-
access cable applications and includes an integrated slack storage basket, interlocking splice trays via a modified keyhole
style stacking module, and an easy to install no special tool sealing system. All major hardware is factory installed to allow
for quick field installation. Universal Multicentric* Grommets along with compression style lateral or branch cable
seals, makes installing the enclosure easy to assemble. The 4048D is a medium capacity closure that can be used in aerial,
pedestal, and underground applications.
*Multicentric is a Registered Trademark of Mar-Don
A-B C-D E F G H
The Starfighter 4000-D Dome Splice Closure is designed for above or below grade applications and supports up to 6 or
more cable entries. The closure has a unique gasketed Split End Plate system that allows for midaccessing cable up to
1.125” in diameter. Branch or lateral cables can be added to any one of four compression seal entry ports. Multiple cables
(up to 6) can also be installed utilizing multi-port grommets available for the closure. The closure requires no special
tools, adhesives, or mastics for installation. Integrated slack storage and hinged trays allow for maximum storage and ac-
cess of fiber and fiber bundles. Splice capacity of 288 single fusion splices using the 4072-SSTP tray 36 splice.
Features & Benefits
tCompletely sealed with compression seal technology
tEase in installation requiring no special tools
tGR-771 and CATV industry compliant
tMid-access design for installation over existing cables without disturbing a working cable
tCan be used for above or below grade applications
tCapacity: w/ (8) 4048 - SSTP - 192 Single Fusion Splices or
Capacity: w/ (8) 4072 - SSTP - 288 Single Fusion Splices
tRUS Listed
Stock ID Description Dimensions Wt. Lbs. UOM
10-8146 4000-D Starfighter Dome Splice Enclosure with one 4072-SSTP Splice Tray 22.0” L x 10.0” D 12.50 Each
020-002-20 4000-D Starfighter Dome Splice Enclosure with one 4048-SSTP Splice Tray 22.0” L x 10.0” D 12.48 Each
10-8007 4048-SSTP 24 Fiber Splice Tray 9.75” L x 4.5” W x 0.5” D 0.57 Each
065-001-10 4072-SSTP 36 Fiber Splice Tray 10.75” L x 5.75” W x 0.5” D 0.59 Each
A B C D-E F G H-I J
Starfighter 2000-F
holds four fiber cables
The Starfighter 2000-F is a medium capacity fiber optic splice closure designed for a majority of splicing applications in
above and below grade installations. The closure supports both aluminum and plastic splice trays and is fully gasketed to
prevent the ingress of water while allowing for ease in entry. The unit is compact and manufactured with highly impact
and corrosion resistant materials.
B
Starfighter 3000-F with a
Cable Addition Kit,
Holds 8 Cables
The Starfighter 3000-F is a high capacity splice closure designed for major splice points in the network. The closure
supports both Inline and Butt configurations and is expandable utilizing an optional cable expansion kit. The closure
utilizes gasketed sealing along with a patented cable seal which allows for mid-span access to the largest cables. The
closure can be used in both above and below grade applications.
1120-SSTA
Stock ID 70902K
Model # 1120-SSTA
Description 12 Single Fusion Splice Tray
Dimensions 6.5” L x 4.75” W x .5” D
Weight Approx. 0.35 lbs.
Material Aluminum
Capacity 12 Single Fusion Splices
2000-SSTA
Stock ID 70506K
Model # 2000-SSTA
Description 24 Single Fusion Splice Tray
Dimensions 11.75” L x 4” W x .5” D
Weight Approx. 0.65 lbs.
Material Aluminum
Capacity 24 Single Fusion Splices
3000-SSTA
Stock ID 70505K
Model # 3000-SSTA
Description 24 Single Fusion Splice Tray
Dimensions 7.75” L x 6” W x .5” D
Weight Approx. 0.54 lbs.
Material Aluminum
Capacity 24 Single Fusion Splices
2020-SSTP
Stock ID 70709K
Model # 2020-SSTP
Description 24 Single Fusion Splice Tray
Dimensions 12.25” L x 4” W x .5” D
Weight Approx. 0.54 lbs.
Material Plastic Base w/ Aluminum Cover
Capacity 24 Single Fusion Splices
3030-SSTP
Stock ID 70706K
Model # 3030-SSTP
Description 24 Single Fusion Splice Tray
Dimensions 8.25” L x 5.75” W x .5” D
Weight Approx. 0.50 lbs.
Material Plastic
Capacity 24 Single Fusion Splices
4048-SSTP
Stock ID 10-8007
Model # 4048-SSTP
Description 24 Single Fusion Splice Tray
Dimensions 9.75” L x 4.5” W x .5” D
Weight Approx. 0.60 lbs.
Material Plastic
Capacity 24 Single or 48 Dual Stacked
4072-SSTP
Stock ID 065-001-10
Model # 4072-SSTP
Description 36 Single Fusion Splice Tray
Dimensions 10.75” L x 5.75” W x .5” D
Weight Approx. 0.60 lbs.
Material Plastic
Capacity 36 Single, 72 Dual Stacked or 144 Mass Fusion
612-SSTP
Stock ID 065-209-10
Model # 612-SSTP
Description 12 Single Fusion Splice Tray
Dimensions 6” L x 2.75” W x .75” D
Weight Approx. 0.10 lbs.
Material Plastic
Capacity 12 Single Fusion Splices
The Multilink Plastic Sno-Shoe® has been designed with two purposes in mind. The first is to store additional lengths of
fiber along the strand for later use. The second is to act as a safeguard, protecting the minimum bend radius of the fiber
optic cable while establishing proper installation practices. The Multilink Plastic Sno-Shoe® is a durable and cost effective
tool for storing fiber optic cable in the air!
Features
tThe plastic material design makes the Sno-Shoe® non-conductive.
tBuilt-in user friendly design features include:
1) Countersunk nut wells for easy one tool installation.
2) The captive design of the Patented Cable Trough™ allows the installer to simply lay the cable in the trough, leaving
both hands free to secure the cable unit.
3) Stackability: The plastic Sno-Shoe® can be stacked in multiple cable configurations to accommodate additional fiber
mount tiering.
4) The multiple slots in the Patented Cable Trough™ allow you to secure the cable with either heavy duty tie-wraps or
stainless steel straps. These slots also allow you to secure additional cable to the unit in expansion situations
without having to remove any of the previously installed cable from the unit and also allows for water and ice
drainage.
Benefits
Why use the Plastic ADSS Sno-Shoe®?
tPrevents microbends in fiber optic cable
tProvides consistency and regularity in fiber optic loops
tSolution to spacing problems on poles
tEliminates costly storage vaults.
tWill not harm fibers
t20 year pro-rated Warranty
tRUS Listed
Installation Applications
Two typical applications for the Multilink Plastic Sno-Shoe® are illustrated below
Application 1
Strand Storage Installation
Application 2
Butt Splice Installation
New for all dielectric self supporting cable! The Multilink Plastic ADSS Sno-Shoe® has been designed with two purposes
in mind. The first is to eliminate the need for slack storage vaults and allow for ADSS slack to be stored aerial for later
use. The second is to act as a safeguard, protecting the minimum bend radius of the fiber optic cable while establishing
proper installation practices. The Multilink Plastic ADSS Sno-Shoe® is a durable and cost effective tool for storing fiber
optic cable in the air!
Features
tThe plastic material design makes the Sno-Shoe® non-conductive.
tBuilt-in user friendly design features include:
1) Countersunk nut wells for easy one tool installation.
2) The captive design of the Patented Cable Trough™ allows the installer to simply lay the cable in the trough, leaving
both hands free to secure the cable unit.
3) Stackability: the plastic Sno-Shoe® can be stacked in multiple cable configurations to accommodate additional fiber
mount tiering.
4) The multiple slots in the Patented Cable Trough™ allow you to secure the cable with either heavy duty tie-wraps or
stainless steel straps. These slots also allow you to secure additional cable to the unit in expansion situations
without having to remove any of the previously installed cable from the unit and also allows for water and ice
drainage.
Benefits
Why use the Plastic ADSS Sno-Shoe®?
tPrevents microbends in fiber optic cable
tProvides consistency and regularity in fiber optic loops
tSolution to spacing problems on poles
tEliminates costly storage vaults.
tWill not harm fibers
t20 year pro-rated Warranty
tRUS Listed
Patent # 5408571 / Patent # D450,0425
The Multilink Plastic Adjustable Sno-Shoe® has been designed for slack storage at 90 degree location where the pole
turns a corner. The 16” (40.6cm) diameter circle design allows two half circle units to be installed on the strand. The half
circle design can be adjusted to the desired coil length. The wide channel allows for the coil to be wrapped numerous
times. The Plastic Adjustable Sno-Shoe® can be adjusted to a captive length of or it can be separated to a desired length
without being captive. In addition, the Plastic Adjustable Sno-Shoe® still serves as a safeguard, protecting the minimum
bend radius of the fiber optic cable while establishing proper installation practices. The Multilink Plastic Adjustable Sno-
Shoe® is a durable and cost effective tool for storing fiber optic cable.
Features
tThe plastic material design makes the Sno-Shoe® non-conductive.
tBuilt-in user friendly design features include:
1) Countersunk nut wells for easy one tool installation.
2) The captive design of the Patented Cable Trough™ allows the installer to simply lay the cable in the trough, leaving
both hands free to secure the cable unit.
3) Stackability: the plastic Sno-Shoe® can be stacked in multiple cable configurations to accommodate additional fiber
mount tiering.
4) The multiple slots in the Patented Cable Trough™ allow you to secure the cable with either heavy duty tie-wraps or
stainless steel straps. These slots also allow you to secure additional cable to the unit in expansion situations
without having to remove any of the previously installed cable from the unit and also allows for water and ice
drainage.
Benefits
Why use the Plastic Adjustable Sno-Shoe®?
tPrevents microbends in fiber optic cable
tProvides consistency and regularity in fiber optic loops
tSolution to spacing problems on poles
tEliminates costly storage vaults.
tWill not harm fibers
t20 year pro-rated Warranty
tRUS Listed
7/8”
2 1/4”
24” is dual sided for more storage Optional 18 and 48-inch Shown with extensions installed
extensions are available
A B C D
Pole Mount Strand Mount Wall Mount Rack Mount
16” 24”
Radii 8” 12”
Length 25” 36.5”
Channel Width 2” 2.25”
Channel Depth 2” .875”
The Multilink Mini Plastic Sno-Shoe was designed to store slack drop fiber optic cable. This unit can be used aerially, wall
mounted, or used in a vault to neatly store excess cable. It protects a minimum bend radius of 3.5” (8.89cm).
Features
tThe plastic material design makes the Sno-Shoe® non-conductive.
tBuilt-in user friendly design features include:
1) Countersunk nut wells for easy one tool installation.
2) The captive design of the Patented Cable Trough™ allows the installer to simply lay the cable in the trough, leaving
both hands free to secure the cable unit.
3) Stackability: the plastic Sno-Shoe® can be stacked in multiple cable configurations to accommodate additional fiber
mount tiering.
4) The multiple slots in the Patented Cable Trough™ allow you to secure the cable with either heavy duty tie-wraps or
stainless steel straps. These slots also allow you to secure additional cable to the unit in expansion situations
without having to remove any of the previously installed cable from the unit and also allows for water and ice
drainage.
Benefits
Why use the Plastic Adjustable Sno-Shoe®?
tPrevents microbends in fiber optic cable
tProvides consistency and regularity in fiber optic loops
tSolution to spacing problems on poles
tEliminates costly storage vaults.
tWill not harm fibers
t20 year pro-rated Warranty Patent Pending
The Starfighter Mid-Span Grounding Closure is specifically designed to allow for meeting grounding and bonding
specifications. The closure has a Gel Seal technology to provide for a water tight seal without the need for any additional
grommets or special seals. The closure is also designed for re-sealing cable sheath damaged as a result of placing or
outside plant events.
tStandard/Stock Colors: Yellow and Orange. Custom Colors: Blue, Green, Gray, White, Brown, and Red
tPlease specify color when placing your order
tOther custom colors available upon request
t500 Minimum Order with both RT & SL part numbers
t5,000 Minimum Order for custom colors
tPlease contact customer service for custom orders and more information
tPlease note: $75.00 one time set-up fee for special logo
Features & Benefits
tAny print or logo your company desires
tUV stabilized body
tOne step installation; Wrap-around design
tAvailable in a variety of colors
tAvailable in three different sizes
tLifetime warranty on printing and a 20 year pro-rated warranty on plastic body
tCustomization provides easy identification of your cables during emergencies or general maintenance
tUV stabilized body won’t degrade in outside applications
tSimple and quick installation: Wrap-around design eliminates the need for special tools and adhesives.
tThe variety of colors offered allow you to segregate your different fiber runs or to distinguish your cables from
pre-existing cables
tThe three different sizes can accommodate a variety of cable configurations
tOur marker will last the life of your system
Stock ID Description Dimensions UOM
Varies MFM-12 Lasered Fiber Optic Cable Marker .5” x 8” (12.7mm x 20.3cm) Each
Varies MFM-15 Lasered Fiber Optic Cable Marker 1” x 8” (25.4mm x 20.3cm) Each
Varies MFM-20 Lasered Fiber Optic Cable Marker 2” x 8” (50.8mm x 20.3cm) Each
Varies MFM-12RT Custom Regular Type Name & # .5” x 8” (12.7mm x 20.3cm) Each
Varies MFM-15RT Custom Regular Type Name & # 1” x 8” (25.4mm x 20.3cm) Each
Varies MFM-20RT Custom Regular Type Name & # 2” x 8” (50.8mm x 20.3cm) Each
Varies MFM-12SL Custom Special Logo & # .5” x 8” (12.7mm x 20.3cm) Each
Varies MFM-15SL Custom Special Logo & # 1” x 8” (25.4mm x 20.3cm) Each
Varies MFM-20SL Custom Special Logo & # 2” x 8” (50.8mm x 20.3cm) Each
Varies *Flag Style Fiber Optic Cable Marker 3.75” L x 4” W Each
Please contact customer service for custom orders and more information.
3615-GS
Stock ID 34118K
Description Plastic Power Splice W/out Connector
Dimensions 4.25” L x 2.375” W x 1.5” H
Weight -
3615-GS closed Material -
UOM Each
4421-UDSP
Stock ID 34402K
Description 100% Underground Drop Sealant Pairs
Dimensions 4.25” L x 2.375” W x 1.5” H
Weight -
Material -
UOM Each
4425-UDSP
Stock ID 34401K
Description 100% Underground Drop Sealant Pairs
Dimensions 4.25” L x 2.375” W x 1.5” H
Weight -
Material -
UOM 50/Bag
3611-GS
Stock ID 34122K-OR
Description For RG7/11 Drop Cable Twisted Pair Orange Kit
Dimensions 7.75” L x 1.5” W x 1.75” H
Weight -
Material Plastic with Silicone
UOM Each
3612-GS
Stock ID 34123K-OR
Description Splice Repair Kit For 0.412 - 0.750 Feeder Cable
Black Kit
Dimensions 12” L x 2.25” W x 3.5” D
Weight -
Material Plastic with Silicone
UOM Each
3614-GS
Stock ID 34145K
Description Multi Gelseal™ Splice Orange Kit
Dimensions 6” L x 2” W x 1” D
Weight -
Material Plastic with Silicone
UOM Each
3616-GS
Stock ID 10-8342
Description For RG59, RG6, RG7, RG11 and 312 Drop Cable
Twisted Pair Black Kit
Dimensions 6” L x 2” W x 1” D
Weight -
Material Plastic with Silicone
UOM Each
Designing and
Engineering
Sheet
Metal
Forming
Precision
Stamping
Finishing
Silk
Screen
Printing
Multilink and DOT’s are doing their part to Conserve Energy and use
Alternative Energy.
Multilink’s Black Hawk, MP Plus, and FlexPower are premium standby power supply products
that DOT’s incorporate into new and existing traffic control systems. Multilink has a complete
line of environmentally controlled enclosures for housing standby power systems and batteries.
Multilink’s Camera Control Interface enables DOT’s to control and monitor such video cameras
and sensors for their traffic monitoring system.
DC Generators