Professional Documents
Culture Documents
i (2)
P
grid
=
3
2
( v
M
+ v
A
)
i = P
M
+ P
A
(3)
v
M
=
2
3
V
dc
S
1M
+ S
2M
e
j
2
3
+ S
3M
e
j
2
3
(4)
v
A
=
2
3
V
dcx
S
1A
+ S
2A
e
j
2
3
+ S
3A
e
j
2
3
(5)
P
A
=
3
2
v
r
2
3
V
dc
S
1M
+ S
2M
e
j
2
3
+ S
3M
e
j
2
3
i (6)
where v
M
, P
M
, and S
iM
(i = 1, 2, 3) represent the main in-
verter voltage, power, and switching function while those of
the auxiliary inverter are given by v
r
, P
M
, and S
iA
(i = 1, 2, 3),
respectively. v
r
represents the output voltage, and P
grid
repre-
sents the real power ow to the grid.
According to (6), it can be deduced that, for a given output
power, supercapacitor power varies with the main inverter
dc-link voltage V
dc
. Therefore, supercapacitor power can be
controlled by controlling the main inverter dc-link voltage.
Furthermore, according to (3), for a given output power, the
main inverter power solely depends on the auxiliary inverter
1026 IEEE TRANSACTIONS ON INDUSTRY APPLICATIONS, VOL. 49, NO. 3, MAY/JUNE 2013
Fig. 6. Controller block diagram of the proposed system.
power. Therefore, the maximum power point of the wind tur-
bine can indirectly be tracked by changing the main inverter
dc-link voltage. The usual practice is to maintain this voltage
at a constant level with the help of a controlled rectier or a
boost rectier placed between the main inverter and the wind
turbine generator (WTG) system. However, in the proposed
system, the boost rectier is used to vary the main inverter
dc-link voltage and thus indirectly track the maximum power
point of the WTG. The controller block diagram for this
indirect maximum power point tracking (MPPT) is shown in
Fig. 6. In this controller, the measured wind speed and the
parameters of the turbine model are used to derive a power
reference for the generator-side converter. The actual generator
power is compared with the reference, and the error is fed
into a proportionalintegral (PI) controller which generates a
voltage reference for the boost rectier. This voltage reference
is normalized to produce the modulation index for the boost
rectier.
IV. MODULATION AND CONTROL OF THE
GRID-SIDE INVERTER
In the proposed system, the main inverter is operated in
the six-step mode, which moves slowly from one vector to
the next. This generates square wave outputs from the main
inverter which get smoothened by the auxiliary inverter. Owing
to this low-frequency operation, the main inverter switching
losses get reduced [14], [15]. The auxiliary inverter, which acts
as an active lter, is operated at high switching frequency by
utilizing a space vector modulation (SVM) method. Therefore,
the overall modulation is a combination of the six-step mode
and SVM. More information on this combined modulation
method can be found in [16] and [17].
The grid-side inverter controller employs an inner current
controller and an outer power controller as shown in Fig. 6.
The grid voltage and current injected into the grid are converted
into the synchronous reference frame. The direct component
of the inverter output current i
d
controls the active power
exchange with the grid while the quadrature component i
q
controls the reactive power. Therefore, to generate a reference
for the direct current component, the instantaneous active power
of the generator-side converter is passed through an LPF [6].
The quadrature current reference i
q
is set to zero to keep the
power factor at the grid connection point at unity. These active
and reactive current references (i
d
and i
q
) are then compared
with actual current components, and the errors are passed
through PI controllers to produce voltage references v
d
and v
q
,
respectively. Equations (7) and (8) are then used to calculate the
amplitude and angle of the reference voltage vector. In (8), is
the initial phase angle of the reference vector
A
m
=
2
d
+ v
2
q
(7)
m
= tan
1
q
v
+ . (8)
V. SUPERCAPACITOR SIZING AND
IMPLEMENTATION ISSUES
The main cause of power uctuations is the change of wind
speed. Therefore, the capacity of the energy storage system
is also a function of the wind speed variation. In order to
analyze this relationship, the wind is modeled as the sum of
a dc quantity and a series of harmonics as in (9) [18]. In the
following simulation, the wind speed uctuation is assumed to
be 20% of the mean value as in (10). The power captured from
the wind can be expressed as in (11).
v
w
(t) =V
w0
+
V
wi
sin (
i
t) (9)
v
w
(t) =V
w0
1 + 0.2 sin
2
T
t
(10)
P(t) =0.5AC
p
v
w
(t)
3
(11)
where v
w
is the instantaneous wind speed, V
w0
is the mean
wind speed, V
wi
is the harmonic amplitude,
i
is the angular
frequency (f = 1/T = /2 = 0.1 10 Hz), is the density
of air, A is the swept area of wind turbine blades, and C
p
is the
coefcient of power conversion.
Power uctuations caused by the aforementioned wind speed
change have to be compensated by the energy storage system.
Therefore, the required capacity of the supercapacitor bank is
determined according to
E
sc,discharg e
=
t
2
t
1
(P(t) P
grid
(t)) dt (12)
C
sc
2E
sc,discharg e
V
2
sc,H
V
2
sc,L
(13)
where E
sc,discharge
is the amount of energy taken out from
the supercapacitor during the discharging period, t
1
and t
2
are the starting time and end time of the discharging period,
respectively, and V
sc,H
and V
sc,L
are the starting and end values
of the supercapacitor voltage.
Supercapacitors behave as resistors at high frequencies (typ-
ically beyond few tens of hertz) [19], [20]. Therefore, the
proposed system requires an electrolytic capacitor to assist
supercapacitors at high frequencies.
VI. SIMULATION RESULTS
The proposed direct integration scheme has been tested
using computer simulations on MATLAB/SIMULINKPLECS
JAYASINGHE et al.: SUPERCAPACITOR DIRECT INTEGRATION SCHEME FOR WIND ENERGY CONVERSION SYSTEM 1027
TABLE I
SYSTEM PARAMETERS OF THE SIMULATION SETUP
Fig. 7. (a) Wind speed prole. (b) Input power P
in
, output power P
grid
,
and supercapacitor power P
sc
. (c) Main inverter dc-link voltage V
dc
and
auxiliary inverter dc-link voltage V
dcx
. (d) Main inverter dc-link current I
dc
and supercapacitor current I
dcx
(low pass ltered).
digital simulation platform. The schematic diagramof the simu-
lation setup is shown in Fig. 1(d), and the corresponding param-
eters of the setup are given in Table I. The wind speed prole
shown in Fig. 7(a) with an average speed of 10 m/s, 20% har-
monic amplitude, and 1-Hz harmonic frequency is used to test
the performance of the proposed system and control strategy.
The corresponding variations of the input power P
in
, the power
injected into the grid P
grid
, and the supercapacitor power P
sc
Fig. 8. (a) Modulation index of the generator-side converter. (b) Generator
current. (c) Amplitude of the grid-side inverter output voltage. (d) Power angle
for the grid-side inverter output voltage. (e) dq-axis components of the grid-
side inverter output current. (f) Inverter output current. (g) Enlarged view of the
inverter output current.
are shown in Fig. 7(b). The input power shows a large variation
ranging from 30 to 100 kW. The average value of the output
power is 60 kW with a small variation of 5 kW. A simple
calculation would reveal that the corresponding input power
uctuation is about 66% while the output power uctuation is
less than 8.4%. This proves the efcacy of the proposed system
in mitigating power uctuations caused by wind changes.
As mentioned in Section III, the main inverter dc-link voltage
is changed to control the supercapacitor power and thus to
indirectly track the MPPT of the WTG. The corresponding
main inverter dc-link voltage and the supercapacitor voltage
1028 IEEE TRANSACTIONS ON INDUSTRY APPLICATIONS, VOL. 49, NO. 3, MAY/JUNE 2013
Fig. 9. (a) Inverter output voltage v
as
. (b) Enlarged view of the inverter
output voltage. (c) v
amg
showing the six-step operation of the main inverter.
(d) v
axgx
showing the PWM operation of the auxiliary inverter.
variations are shown in Fig. 7(c). According to this diagram, the
main inverter dc-link voltage shows a large variation ranging
from 400 to 1200 V which is far below the upper limit of
modern IGCT devices, and therefore, the proposed system is
feasible. Similarly, the supercapacitor voltage varies with a
maximum of V
sc,H
= 800 V and a minimum of V
sc,L
= 400 V.
Therefore, according to (12) and (13), the required minimum
capacitance of the supercapacitor bank is found to be 43.75 mF
which is a realistic value.
The main inverter dc-link current and supercapacitor current
variations are shown in Fig. 7(d). The main inverter dc-link
current is nearly constant due to the six-step operation of
the main inverter. However, the supercapacitor current varies
with the main inverter dc-link voltage owing to the pulsewidth
modulation (PWM) operation of the auxiliary inverter.
The change of the modulation index of the generator-side
converter (boost rectier) for the aforementioned wind speed
prole is shown in Fig. 8(a). The corresponding generator
currents are shown in Fig. 8(b). Similarly, the variations of
the amplitude and power angle of the grid-side inverter output
voltage are shown in Fig. 8(c) and (d), respectively. These two
values are nearly constant owing to the smooth power delivery
to the grid. Consequently, the dq-axis currents of the grid-
side inverter are nearly constant as shown in Fig. 8(e). The
corresponding three phase currents of the grid-side inverter
and their zoomed-in view are shown in Fig. 8(f) and (g),
respectively, to illustrate the low harmonic distortion of the dual
inverter arrangement.
The inverter output voltage of the a-phase is shown in
Fig. 9(a). An enlarged view of the inverter output voltage is
given in Fig. 9(b) to show the multilevel operation of the
Fig. 10. (a) Schematic diagram of the experimental setup. (b) Photographs of
the experimental setup.
TABLE II
SYSTEM PARAMETERS OF THE EXPERIMENTAL SETUP
proposed dual inverter system. The two gures shown in
Fig. 9(c) and (d) depict the six-step operation of the main
inverter and the PWM operation of the auxiliary inverter,
respectively.
VII. EXPERIMENTAL RESULTS
The schematic diagram and photographs of the laboratory
prototype are shown in Fig. 10(a) and (b), respectively. The two
inverters are coupled through an RL load, and their parameters
are given in Table II. A large capacitor bank is used to emulate
the high capacitance of the supercapacitor. The controller is set
to regulate the output power to a given reference. The result
of this output power regulation is shown in Fig. 11(a) by the
graph marked with P
out
. The input power and supercapacitor
power variations are also plotted in the same gure and are
marked as P
in
and P
sc
, respectively. In order to emulate the
JAYASINGHE et al.: SUPERCAPACITOR DIRECT INTEGRATION SCHEME FOR WIND ENERGY CONVERSION SYSTEM 1029
Fig. 11. Experimental results showing the power smoothening capability.
(a) Input power, output power, and supercapacitor power. (b) DC-link volt-
age variations. (c) Variations of average dc-link currents. (d) Output voltage
(a-phase). (e) Output current (a-phase).
WTG and to obtain the input power prole shown in Fig. 11(a),
a programmable ac source is used with a bridge rectier. The
ac source is programmed in a way that the rectier output,
i.e., the main inverter dc-link voltage, is varied as shown in
Fig. 11(b) by the trace marked as V
dc
. The corresponding su-
percapacitor voltage variation V
dcx
is also shown in Fig. 11(b).
The resultant average supercapacitor current variation is shown
in Fig. 11(c). An enlarged view of the load voltage is given
in Fig. 11(d) to show the multilevel operation of the proposed
dual inverter system. The inverter output current waveform,
shown in Fig. 11(e), proves the efcacy of the proposed system
in generating outputs with very low distortions under variable
dc-link voltage conditions.
VIII. CONCLUSION
The direct integration of energy storage devices has a number
of advantages such as reduction in power losses, cost, and
complexity. Therefore, in this paper, the popular dual inverter
topology was customized to connect a supercapacitor bank
directly into the dc link of the auxiliary inverter. The operation
of the proposed system was discussed in detail. Simulation
and experimental results were presented to verify the efcacy
of the proposed system in suppressing short-term wind power
uctuations.
REFERENCES
[1] T. Kinjo, T. Senjyu, N. Urasaki, and H. Fujita, Output leveling of renew-
able energy by electric double-layer capacitor applied for energy storage
system, IEEE Trans. Energy Convers., vol. 21, no. 1, pp. 221227,
Mar. 2006.
[2] E. Naswali, C. Alexander, H. Y. Han, D. Naviaux, A. Bistrika, A. Jouanne,
A. Yokochi, and T. K. A. Brekken, Supercapacitor energy storage for
wind energy integration, in Proc. ECCE, Sep. 1721, 2011, pp. 298305.
[3] L. Qu and W. Qiao, Constant power control of DFIG wind turbines with
supercapacitor energy storage, IEEE Trans. Ind. Appl., vol. 47, no. 1,
pp. 359367, Jan./Feb. 2011.
[4] N. Bingchang and C. Sourkounis, Energy yield and power uctuation of
different control methods for wind energy converters, IEEE Trans. Ind.
Appl., vol. 47, no. 3, pp. 14801486, May/Jun. 2011.
[5] M.-S. Lu, C. L. Chang, W.-J. Lee, and L. Wang, Combining the wind
power generation system with energy storage equipment, IEEE Trans.
Ind. Appl., vol. 45, no. 6, pp. 21092115, Nov./Dec. 2009.
[6] S. M. Muyeen, R. Takahashi, T. Murata, and J. Tamura, Integration of
an energy capacitor system with a variable-speed wind generator, IEEE
Trans. Energy Convers., vol. 24, no. 3, pp. 740749, Sep. 2009.
[7] Li. Wei, G. Joos, and J. Belanger, Real-time simulation of a wind turbine
generator coupled with a battery supercapacitor energy storage system,
IEEE Trans. Ind. Electron., vol. 57, no. 4, pp. 11371145, Apr. 2010.
[8] G. Guidi, T. M. Undeland, and Y. Hori, An optimized converter for
battery-supercapacitor interface, in Proc. IEEE Power Electron. Spec.
Conf., Jun. 2007, pp. 29762981.
[9] C. Abbey and G. Joos, Supercapacitor energy storage for wind en-
ergy applications, IEEE Trans. Ind. Appl., vol. 43, no. 3, pp. 769776,
May/Jun. 2007.
[10] L. Allegre, A. Bouscayrol, and R. Trigui, Inuence of control strate-
gies on battery/supercapacitor hybrid energy storage systems for traction
applications, in Proc. IEEE Veh. Power Propulsion Conf., Sep. 2009,
pp. 213220.
[11] Abedini and A. Nasiri, Applications of super capacitors for PMSG wind
turbine power smoothing, in Proc. IEEE Ind. Electron. Conf., Nov. 2008,
pp. 33473351.
[12] K. Jin, M. Yang, X.-B. Ruan, and M. Xu, Three-level bidirectional
converter for fuel-cell/battery hybrid power system, IEEE Trans. Ind.
Electron., vol. 57, no. 6, pp. 19761986, Jun. 2010.
[13] L. Wei and G. Joos, Comparison of energy storage system technologies
and congurations in a wind farm, in Proc. IEEE Power Electron. Spec.
Conf., Jun. 2007, pp. 12801285.
1030 IEEE TRANSACTIONS ON INDUSTRY APPLICATIONS, VOL. 49, NO. 3, MAY/JUNE 2013
[14] K. A. Corzine, W. Wielebsk, F. Z. Peng, and J. Wang, Control of cas-
caded multilevel inverters, IEEE Trans. Power Electron., vol. 19, no. 3,
pp. 732738, May 2004.
[15] S. Lu and K. A. Corzine, Advanced control and analysis of cascaded
multilevel converters based on P-Q compensation, IEEE Trans. Power
Electron., vol. 22, no. 4, pp. 12421252, Jul. 2007.
[16] S. D. G. Jayasinghe, D. M. Vilathgamuwa, and U. K. Madawala, Di-
rect integration of battery energy storage systems in distributed power
generation, IEEE Trans. Energy Convers., vol. 26, no. 2, pp. 677685,
Jun. 2011.
[17] S. D. G. Jayasinghe, D. M. Vilathgamuwa, and U. K. Madawala, A dual
inverter with integrated energy storage for wind power systems, in Proc.
IPEC, Sapporo, Japan, Jun. 2125, 2010, pp. 31823187.
[18] T. H. Nguyen, D. C. Lee, S. S. Ho, and E. H. Kim, Improvement of
power quality for PMSG wind turbine systems, in Proc. IEEE ECCE,
Sep. 1216, 2010, pp. 27632770.
[19] W. Lajnef, J. M. Vinassa, O. Briat, S. Azzopardi, and C. Zardini, Study
of ultracapacitors dynamic behaviour using impedance frequency anal-
ysis on a specic test bench, in Proc. IEEE Int. Symp. Ind. Electron.,
May 47, 2004, vol. 2, pp. 839844.
[20] S. Buller, M. Thele, R. W. A. A. De Doncker, and E. Karden, Impedance-
based simulation models of supercapacitors and Li-ion batteries for power
electronic applications, IEEE Trans. Ind. Appl., vol. 41, no. 3, pp. 742
747, May/Jun. 2005.
S. D. Gamini Jayasinghe (S10M12) received
the B.Sc. degree in electronics and telecommunica-
tion engineering from the University of Moratuwa
(UoM), Moratuwa, Sri Lanka, in 2003. He is cur-
rently working toward the Ph.D. degree in the School
of Electrical and Electronic Engineering, Nanyang
Technological University, Singapore.
From 2004 to 2007, he was with the Dialog UoM
Mobile Communications Research Laboratory as a
Research Engineer.
D. Mahinda Vilathgamuwa (S90M93SM99)
received the B.Sc. degree in electrical engineer-
ing from the University of Moratuwa, Moratuwa,
Sri Lanka, in 1985 and the Ph.D. degree in electri-
cal engineering from the University of Cambridge,
Cambridge, U.K., in 1993.
Since 1993, he has been with the School of Electri-
cal and Electronic Engineering, Nanyang Technolog-
ical University, Singapore, where he was a Lecturer
and is currently an Associate Professor. His current
research interests include power electronic convert-
ers, electrical drives, and power quality.
Dr. Vilathgamuwa is currently the Chairman of the IEEE Singapore Section
and a member of the Power Electronics Technical Committee of the IEEE
Industrial Electronics Society.
Udaya K. Madawala (M95SM06) received the
B.Sc.(Hons.) degree in electrical engineering from
the University of Moratuwa, Moratuwa, Sri Lanka,
in 1987 and the Ph.D. degree in power electron-
ics from The University of Auckland, Auckland,
New Zealand, in 1993.
After working in industry, he joined the Depart-
ment of Electrical and Computer Engineering, The
University of Auckland, as a Research Fellow in
1997. At present, he is an Associate Professor, and
his research interests are in the elds of power elec-
tronics, inductive power transfer, and renewable energy.
Dr. Madawala is an active IEEE volunteer and serves as an Associate Editor
for both the IEEE TRANSACTIONS ON INDUSTRIAL ELECTRONICS and IEEE
TRANSACTIONS ON POWER ELECTRONICS. He is the Chairman of the IEEE
Industrial Electronics Chapter in New Zealand and a member of the Power
Electronics Technical Committee of the IEEE Industrial Electronics Society.