You are on page 1of 150

Vertically Polarized Directional Panel Antennas

806-900 MHz, 806-960 MHz


Model Number
Frequency Range
(MHz)
H-Plane E-Plane
Gain
(dBd)
Fixed Electrical
Downtilt Options
Length x Width x Depth
(in inches)
WPA-80063/2CF _ 806-900 MHz 63 30 10 dBd 0 23.8 x 11.8 x 3.9
WPA-80063/4CF _ 806-960 MHz 63 16 13 dBd 0, 2, 5 47.4 x 11.8 x 3.9
WPA-80063/6CF _ 806-960 MHz 63 11 14.5 dBd 0, 5 71.0 x 11.8 x 3.9
WPA-80063/8CF _ 806-960 MHz 63 7 16.5 dBd 0, 2, 5, 10 94.7 x 11.8 x 3.9
WPA-80080/2CF _ 806-900 MHz 80 30 9.5 dBd 0 23.8 x 11.2 x 4.5
WPA-80080/4CF _ 806-960 MHz 80 15 12 dBd 0, 5 47.4 x 11.2 x 4.5
WPA-80080/6CF _ 806-960 MHz 80 11 13.5 dBd 0, 4 71.1 x 11.2 x 4.5
WPA-80080/8CF _ 806-960 MHz 80 7 15 dBd 0, 5 94.7 x 11.2 x 4.5
WPA-80090/2CF _ 806-900 MHz 90 30 9 dBd 0 23.8 x 8.1 x 5.7
WPA-80090/4CF _ 806-960 MHz 90 15 11.5 dBd 0, 5 47.4 x 8.1 x 5.7
WPA-80090/6CF _ 806-960 MHz 90 11 13 dBd 0, 5 71.1 x 8.1 x 5.7
WPA-80090/8CF _ 806-960 MHz 90 7 14.5 dBd 0, 5 94.7 x 8.1 x 5.7
WPA-800120/6CF _ 806-960 MHz 120 11 12 dBd 0, 5 70.9 x 5.6 x 5.6
WPA-800 Series
The WPA (Wideband Panel Antenna) is a directional antenna operating within the 806-900 MHz and 806-960 MHz frequency range.
These vertically polarized panel antennas are light-weight and low-profile and offer excellent upper side lobe suppression and hor-
izontal roll-off. WPAs are ideal for sectorized sites in which cost is a factor and tower issues are present. Antennas are available
with fixed electrical downtilt.
Design and Construction of the WPA-800 Panel:
WPA antennas are manufactured with our exclusive 3T Technology, featuring single-piece, water-cut brass feedline assemblies for
consistent performance; a non-collinear system with access to each radiating element for control of the shaping of the vertical pat-
tern; air as insulation for virtually no internal signal loss; fiberglass radomes and aircraft grade aluminum reflector plates for even
heat dissipation to minimize plate warping and bending.
Model Number Guide:
Amphenol Antel, Inc.
Models Currently Available:
WPA- 800 63 / 8 CF E-DIN 5
Electrical Downtilt
Connector Type
NE is an elongated N connector
E-DIN is an elongated DIN connector
BF refers to a Bottom-Fed connector
CF refers to a Center-Fed connector
TF refers to a Top-Fed connector
Number of radiating element sets
Also refers to the approx. length in feet
Horizontal Beamwidth
Operating Frequency Range
800 =Operates within 806-960 MHz
When ordering replace __ with the connector type (NE or E-DIN).
Ver t i c al l y Pol ar i zed, Panel 63 / 10 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
WPA-80063/2CF __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mec hani c al spec i f i c at i ons
Length 604 mm 23.8 in
Width 300 mm 11.8 in
Depth
Depth with z-bracket
100
140
mm
mm
3.9
5.5
in
in
4)
Weight 3.2 kg 7.0 lbs
Wind Area
Fore/Aft 0.18 m
2
1.95 ft
2
Side 0.06 m
2
0.65 ft
2
Rated Wind Velocity (Safety factor 2.0)
>486 km/hr >302 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 257 N 57.8 lbs
Side 88 N 19.7 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36211102
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 10 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 63
E-Plane 30
1)
Electrical Downtilt 0
1)
Null Fill 0%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
Watercut brass feedline assembly for
consistent performance.
Unique feedline design eliminates the need
for conventional solder joints in the signal
path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 63 / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
WPA-80063/4CF __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mec hani c al spec i f i c at i ons
Length 1205 mm 47.4 in
Width 300 mm 11.8 in
Depth
Depth with z-bracket
100
140
mm
mm
3.9
5.5
in
in
4)
Weight 5.4 kg 12.0 lbs
Wind Area
Fore/Aft 0.36 m
2
3.9 ft
2
Side 0.12 m
2
1.3 ft
2
Rated Wind Velocity (Safety factor 2.0)
>431 km/hr >267 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 516 N 116.0 lbs
Side 194 N 43.7 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 13 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 63
E-Plane 16
1)
Electrical Downtilt 0
1)
Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
Watercut brass feedline assembly for
consistent performance.
Unique feedline design eliminates the need
for conventional solder joints in the signal
path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 63 / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
WPA-80063/4CF __ 2
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mec hani c al spec i f i c at i ons
Length 1205 mm 47.4 in
Width 300 mm 11.8 in
Depth
Depth with z-bracket
100
140
mm
mm
3.9
5.5
in
in
4)
Weight 5.4 kg 12.0 lbs
Wind Area
Fore/Aft 0.36 m
2
3.9 ft
2
Side 0.12 m
2
1.3 ft
2
Rated Wind Velocity (Safety factor 2.0)
>431 km/hr >267 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 516 N 116.0 lbs
Side 194 N 43.7 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 13 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 63
E-Plane 16
1)
Electrical Downtilt 2
1)
Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
Watercut brass feedline assembly for
consistent performance.
Unique feedline design eliminates the need
for conventional solder joints in the signal
path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 63 / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
WPA-80063/4CF __ 5
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mec hani c al spec i f i c at i ons
Length 1205 mm 47.4 in
Width 300 mm 11.8 in
Depth
Depth with z-bracket
100
140
mm
mm
3.9
5.5
in
in
4)
Weight 5.4 kg 12.0 lbs
Wind Area
Fore/Aft 0.36 m
2
3.9 ft
2
Side 0.12 m
2
1.3 ft
2
Rated Wind Velocity (Safety factor 2.0)
>431 km/hr >267 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 516 N 116.0 lbs
Side 194 N 43.7 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 13 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 63
E-Plane 16
1)
Electrical Downtilt 5
1)
Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
Watercut brass feedline assembly for
consistent performance.
Unique feedline design eliminates the need
for conventional solder joints in the signal
path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 63 / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
WPA-80063/6CF __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mec hani c al spec i f i c at i ons
Length 1804 mm 71.0 in
Width 300 mm 11.8 in
Depth
Depth with z-bracket
100
140
mm
mm
3.9
5.5
in
in
4)
Weight 6.8 kg 15.0 lbs
Wind Area
Fore/Aft 0.54 m
2
5.8 ft
2
Side 0.18 m
2
1.9 ft
2
Rated Wind Velocity (Safety factor 2.0)
>459 km/hr >284 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 791 N 177.9 lbs
Side 322 N 72.4 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 14.5 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 63
E-Plane 11
1)
Electrical Downtilt 0
1)
Null Fill 15%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
Watercut brass feedline assembly for
consistent performance.
Unique feedline design eliminates the need
for conventional solder joints in the signal
path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 63 / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
WPA-80063/6CF __ 5
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mec hani c al spec i f i c at i ons
Length 1804 mm 71.0 in
Width 300 mm 11.8 in
Depth
Depth with z-bracket
100
140
mm
mm
3.9
5.5
in
in
4)
Weight 6.8 kg 15.0 lbs
Wind Area
Fore/Aft 0.54 m
2
5.8 ft
2
Side 0.18 m
2
1.9 ft
2
Rated Wind Velocity (Safety factor 2.0)
>459 km/hr >284 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 791 N 177.9 lbs
Side 322 N 72.4 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 14.5 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 63
E-Plane 11
1)
Electrical Downtilt 5
1)
Null Fill 15%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
Watercut brass feedline assembly for
consistent performance.
Unique feedline design eliminates the need
for conventional solder joints in the signal
path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 63 / 16.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
WPA-80063/8CF __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mec hani c al spec i f i c at i ons
Length 2404 mm 94.7 in
Width 300 mm 11.8 in
Depth
Depth with z-bracket
100
140
mm
mm
3.9
5.5
in
in
4)
Weight 8.6 kg 19.0 lbs
Wind Area
Fore/Aft 0.72 m
2
7.8 ft
2
Side 0.24 m
2
2.6 ft
2
Rated Wind Velocity (Safety factor 2.0)
>340 km/hr >211 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1078 N 242.7 lbs
Side 455 N 102.4 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 16.5 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 63
E-Plane 7
1)
Electrical Downtilt 0
1)
Null Fill 10-15%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
Watercut brass feedline assembly for
consistent performance.
Unique feedline design eliminates the need
for conventional solder joints in the signal
path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 63 / 16.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
WPA-80063/8CF __ 2
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mec hani c al spec i f i c at i ons
Length 2404 mm 94.7 in
Width 300 mm 11.8 in
Depth
Depth with z-bracket
100
140
mm
mm
3.9
5.5
in
in
4)
Weight 8.6 kg 19.0 lbs
Wind Area
Fore/Aft 0.72 m
2
7.8 ft
2
Side 0.24 m
2
2.6 ft
2
Rated Wind Velocity (Safety factor 2.0)
>340 km/hr >211 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1078 N 242.7 lbs
Side 455 N 102.4 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 16.5 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 63
E-Plane 7
1)
Electrical Downtilt 2
1)
Null Fill 10-15%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
Watercut brass feedline assembly for
consistent performance.
Unique feedline design eliminates the need
for conventional solder joints in the signal
path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 63 / 16.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
WPA-80063/8CF __ 5
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mec hani c al spec i f i c at i ons
Length 2404 mm 94.7 in
Width 300 mm 11.8 in
Depth
Depth with z-bracket
100
140
mm
mm
3.9
5.5
in
in
4)
Weight 8.6 kg 19.0 lbs
Wind Area
Fore/Aft 0.72 m
2
7.8 ft
2
Side 0.24 m
2
2.6 ft
2
Rated Wind Velocity (Safety factor 2.0)
>340 km/hr >211 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1078 N 242.7 lbs
Side 455 N 102.4 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 16.5 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 63
E-Plane 7
1)
Electrical Downtilt 5
1)
Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
Watercut brass feedline assembly for
consistent performance.
Unique feedline design eliminates the need
for conventional solder joints in the signal
path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 63 / 16.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
WPA-80063/8CF __ 10
Revision Date: 8/9/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2404 mm 94.7 in
Width 300 mm 11.8 in
Depth
Depth with z-bracket
100
140
mm
mm
3.9
5.5
in
in
4)
Weight 8.6 kg 19.0 lbs
Wind Area
Fore/Aft 0.72 m
2
7.8 ft
2
Side 0.24 m
2
2.6 ft
2
Rated Wind Velocity (Safety factor 2.0)
>340 km/hr >211 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1078 N 242.7 lbs
Side 455 N 102.4 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-941 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 16.5 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 63
E-Plane 7
1)
Electrical Downtilt 10
1)
Null Fill 10-15%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
Watercut brass feedline assembly for
consistent performance.
Unique feedline design eliminates the need
for conventional solder joints in the signal
path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 80 / 9.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
WPA-80080/2CF __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mec hani c al spec i f i c at i ons
Length 604 mm 23.8 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
114
154
mm
mm
4.5
6.1
in
in
4)
Weight 2.2 kg 4.9 lbs
Wind Area
Fore/Aft 0.18 m
2
1.80 ft
2
Side 0.07 m
2
0.76 ft
2
Rated Wind Velocity (Safety factor 2.0)
>800 km/hr >500 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 248 N 56 lbs
Side 102 N 23 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36211102
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 9.5 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 80
E-Plane 30
1)
Electrical Downtilt 0
1)
Null Fill 0%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
Watercut brass feedline assembly for
consistent performance.
Unique feedline design eliminates the need
for conventional solder joints in the signal
path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 80 / 12 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
WPA-80080/4CF __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mec hani c al spec i f i c at i ons
Length 1205 mm 47.4 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
114
154
mm
mm
4.5
6.1
in
in
4)
Weight 4.5 kg 9.9 lbs
Wind Area
Fore/Aft 0.36 m
2
3.9 ft
2
Side 0.15 m
2
1.6 ft
2
Rated Wind Velocity (Safety factor 2.0)
>653 km/hr >406 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 522 N 117 lbs
Side 233 N 52 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 12 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 80
E-Plane 15
1)
Electrical Downtilt 0
1)
Null Fill 5-10%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
Watercut brass feedline assembly for
consistent performance.
Unique feedline design eliminates the need
for conventional solder joints in the signal
path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 80 / 12 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
WPA-80080/4CF __ 5
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mec hani c al spec i f i c at i ons
Length 1205 mm 47.4 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
114
154
mm
mm
4.5
6.1
in
in
4)
Weight 4.5 kg 9.9 lbs
Wind Area
Fore/Aft 0.36 m
2
3.9 ft
2
Side 0.15 m
2
1.6 ft
2
Rated Wind Velocity (Safety factor 2.0)
>653 km/hr >406 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 522 N 117 lbs
Side 233 N 52 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 12 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 80
E-Plane 15
1)
Electrical Downtilt 5
1)
Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
Watercut brass feedline assembly for
consistent performance.
Unique feedline design eliminates the need
for conventional solder joints in the signal
path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 80 / 13.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
WPA-80080/6CF __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mec hani c al spec i f i c at i ons
Length 1804 mm 71.1 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
114
154
mm
mm
4.5
6.1
in
in
4)
Weight 6.8 kg 14.9 lbs
Wind Area
Fore/Aft 0.54 m
2
5.8 ft
2
Side 0.21 m
2
2.3 ft
2
Rated Wind Velocity (Safety factor 2.0)
>438 km/hr >272 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 790 N 178 lbs
Side 353 N 80 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 13.5 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 80
E-Plane 11
1)
Electrical Downtilt 0
1)
Null Fill 10-15%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
Watercut brass feedline assembly for
consistent performance.
Unique feedline design eliminates the need
for conventional solder joints in the signal
path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 80 / 13.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
WPA-80080/6CF __ 4
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mec hani c al spec i f i c at i ons
Length 1804 mm 71.1 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
114
154
mm
mm
4.5
6.1
in
in
4)
Weight 6.8 kg 14.9 lbs
Wind Area
Fore/Aft 0.54 m
2
5.8 ft
2
Side 0.21 m
2
2.3 ft
2
Rated Wind Velocity (Safety factor 2.0)
>438 km/hr >272 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 790 N 178 lbs
Side 353 N 80 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 13.5 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 80
E-Plane 11
1)
Electrical Downtilt 4
1)
Null Fill 10-15%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
Watercut brass feedline assembly for
consistent performance.
Unique feedline design eliminates the need
for conventional solder joints in the signal
path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 80 / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
WPA-80080/8CF __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mec hani c al spec i f i c at i ons
Length 2405 mm 94.7 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
114
154
mm
mm
4.5
6.1
in
in
4)
Weight 10.9 kg 24.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.5 ft
2
Side 0.28 m
2
3.0 ft
2
Rated Wind Velocity (Safety factor 2.0)
>333 km/hr >207 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1048 N 236 lbs
Side 510 N 115 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 15 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 80
E-Plane 7
1)
Electrical Downtilt 0
1)
Null Fill 10-15%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
Watercut brass feedline assembly for
consistent performance.
Unique feedline design eliminates the need
for conventional solder joints in the signal
path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 80 / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
WPA-80080/8CF __ 5
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mec hani c al spec i f i c at i ons
Length 2405 mm 94.7 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
114
154
mm
mm
4.5
6.1
in
in
4)
Weight 10.9 kg 24.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.5 ft
2
Side 0.28 m
2
3.0 ft
2
Rated Wind Velocity (Safety factor 2.0)
>333 km/hr >207 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1048 N 236 lbs
Side 510 N 115 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 15 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 80
E-Plane 7
1)
Electrical Downtilt 5
1)
Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
Watercut brass feedline assembly for
consistent performance.
Unique feedline design eliminates the need
for conventional solder joints in the signal
path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 90 / 9 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
WPA-80090/2CF __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mec hani c al spec i f i c at i ons
Length 604 mm 23.8 in
Width 205 mm 8.1 in
Depth
Depth with z-bracket
145
185
mm
mm
5.7
7.3
in
in
4)
Weight 2.1 kg 4.6 lbs
Wind Area
Fore/Aft 0.12 m
2
1.33 ft
2
Side 0.09 m
2
0.92 ft
2
Rated Wind Velocity (Safety factor 2.0)
>800 km/hr >500 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 176 N 39.5 lbs
Side 122 N 27.5 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36211102
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 9 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 90
E-Plane 30
1)
Electrical Downtilt 0
1)
Null Fill 0%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
Watercut brass feedline assembly for
consistent performance.
Unique feedline design eliminates the need
for conventional solder joints in the signal
path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 90 / 11.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
WPA-80090/4CF __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mec hani c al spec i f i c at i ons
Length 1205 mm 47.4 in
Width 205 mm 8.1 in
Depth
Depth with z-bracket
145
185
mm
mm
5.7
7.3
in
in
4)
Weight 5.4 kg 12.0 lbs
Wind Area
Fore/Aft 0.25 m
2
2.7 ft
2
Side 0.17 m
2
1.9 ft
2
Rated Wind Velocity (Safety factor 2.0)
>679 km/hr >422 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 362 N 81.4 lbs
Side 264 N 59.4 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 11.5 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 90
E-Plane 15
1)
Electrical Downtilt 0
1)
Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
Watercut brass feedline assembly for
consistent performance.
Unique feedline design eliminates the need
for conventional solder joints in the signal
path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 90 / 11.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
WPA-80090/4CF __ 5
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mec hani c al spec i f i c at i ons
Length 1205 mm 47.4 in
Width 205 mm 8.1 in
Depth
Depth with z-bracket
145
185
mm
mm
5.7
7.3
in
in
4)
Weight 5.4 kg 12.0 lbs
Wind Area
Fore/Aft 0.25 m
2
2.7 ft
2
Side 0.17 m
2
1.9 ft
2
Rated Wind Velocity (Safety factor 2.0)
>679 km/hr >422 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 362 N 81.4 lbs
Side 264 N 59.4 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 11.5 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 90
E-Plane 15
1)
Electrical Downtilt 5
1)
Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
Watercut brass feedline assembly for
consistent performance.
Unique feedline design eliminates the need
for conventional solder joints in the signal
path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 90 / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
WPA-80090/6CF __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mec hani c al spec i f i c at i ons
Length 1805 mm 71.1 in
Width 205 mm 8.1 in
Depth
Depth with z-bracket
145
185
mm
mm
5.7
7.3
in
in
4)
Weight 8.2 kg 18.0 lbs
Wind Area
Fore/Aft 0.37 m
2
3.9 ft
2
Side 0.26 m
2
2.8 ft
2
Rated Wind Velocity (Safety factor 2.0)
>452 km/hr >281 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 558 N 126.0 lbs
Side 433 N 97.4 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 13 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 90
E-Plane 11
1)
Electrical Downtilt 0
1)
Null Fill 10-15%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
Watercut brass feedline assembly for
consistent performance.
Unique feedline design eliminates the need
for conventional solder joints in the signal
path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 90 / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
WPA-80090/6CF __ 5
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mec hani c al spec i f i c at i ons
Length 1805 mm 71.1 in
Width 205 mm 8.1 in
Depth
Depth with z-bracket
145
185
mm
mm
5.7
7.3
in
in
4)
Weight 8.2 kg 18.0 lbs
Wind Area
Fore/Aft 0.37 m
2
3.9 ft
2
Side 0.26 m
2
2.8 ft
2
Rated Wind Velocity (Safety factor 2.0)
>452 km/hr >281 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 558 N 126.0 lbs
Side 433 N 97.4 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 13 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 90
E-Plane 11
1)
Electrical Downtilt 5
1)
Null Fill 10%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
Watercut brass feedline assembly for
consistent performance.
Unique feedline design eliminates the need
for conventional solder joints in the signal
path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 90 / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
WPA-80090/8CF __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mec hani c al spec i f i c at i ons
Length 2405 mm 94.7 in
Width 205 mm 8.1 in
Depth
Depth with z-bracket
145
185
mm
mm
5.7
7.3
in
in
4)
Weight 10.4 kg 23.0 lbs
Wind Area
Fore/Aft 0.49 m
2
5.3 ft
2
Side 0.35 m
2
3.8 ft
2
Rated Wind Velocity (Safety factor 2.0)
>323 km/hr >201 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 793 N 178.4 lbs
Side 591 N 132.9 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 14.5 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 90
E-Plane 7
1)
Electrical Downtilt 0
1)
Null Fill 10-15%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
Watercut brass feedline assembly for
consistent performance.
Unique feedline design eliminates the need
for conventional solder joints in the signal
path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 90 / 14.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
WPA-80090/8CF __ 5
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Featuring upper side
lobe suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mec hani c al spec i f i c at i ons
Length 2405 mm 94.7 in
Width 205 mm 8.1 in
Depth
Depth with z-bracket
145
185
mm
mm
5.7
7.3
in
in
4)
Weight 10.4 kg 23.0 lbs
Wind Area
Fore/Aft 0.49 m
2
5.3 ft
2
Side 0.35 m
2
3.8 ft
2
Rated Wind Velocity (Safety factor 2.0)
>323 km/hr >201 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 793 N 178.4 lbs
Side 591 N 132.9 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-127 mm (2.0-5.0 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 14.5 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 90
E-Plane 7
1)
Electrical Downtilt 5
1)
Null Fill 10-15%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
Watercut brass feedline assembly for
consistent performance.
Unique feedline design eliminates the need
for conventional solder joints in the signal
path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 120 / 12 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
WPA-800120/6CF __
Revision Date: 7/12/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mec hani c al spec i f i c at i ons
Length 1801 mm 70.9 in
Width 141 mm 5.6 in
Depth
Depth with t-bracket
142
170
mm
mm
5.6
6.7
in
in
4)
Weight 5 kg 11.0 lbs
Wind Area
Fore/Aft 0.26 m
2
2.8 ft
2
Side 0.26 m
2
2.8 ft
2
Rated Wind Velocity (Safety factor 2.0)
>328 km/hr >204 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 429 N 96.4 lbs
Side 423 N 95.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-102 mm (2.0-4.0 in).
Mounting bracket kit #26799997
Downtilt bracket kit #26799999
The downtilt bracket kit includes the mounting
bracket kit.
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 12 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 120
E-Plane 11
1)
Electrical Downtilt 0
1)
Null Fill 10-15%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
Watercut brass feedline assembly for
consistent performance.
Unique feedline design eliminates the need
for conventional solder joints in the signal
path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 120 / 12 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
WPA-800120/6CF __ 5
Revision Date: 7/12/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mec hani c al spec i f i c at i ons
Length 1801 mm 70.9 in
Width 141 mm 5.6 in
Depth
Depth with t-bracket
142
170
mm
mm
5.6
6.7
in
in
4)
Weight 5 kg 11.0 lbs
Wind Area
Fore/Aft 0.26 m
2
2.8 ft
2
Side 0.26 m
2
2.8 ft
2
Rated Wind Velocity (Safety factor 2.0)
>328 km/hr >204 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 429 N 96.4 lbs
Side 423 N 95.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-102 mm (2.0-4.0 in).
Mounting bracket kit #26799997
Downtilt bracket kit #26799999
The downtilt bracket kit includes the mounting
bracket kit.
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Patented Dipole Design: U.S. Patent No. 6,229,496 B1
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 12 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 120
E-Plane 11
1)
Electrical Downtilt 5
1)
Null Fill 10-15%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
Watercut brass feedline assembly for
consistent performance.
Unique feedline design eliminates the need
for conventional solder joints in the signal
path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed
connector only.
1300 Capital Drive Rockford, IL 61109 Toll-Free (888) 417-9562 Tel. (815) 399-0001
Fax. (815) 399-0156 Email: antel@antelinc.com www.antelinc.com

Mount i ng & Dow nt i l t Br ac k et Ki t s
WPA Br ac ket Ki t s
Part Number Bracket Type

36210002 Standard WPA
Mounting Bracket
Kit for:

WPA-80063/2CF
WPA-80063/4CF
WPA-80063/6CF
WPA-80063/8CF
WPA-80080/2CF
WPA-80080/4CF
WPA-80080/6CF
WPA-80080/8CF
WPA-80090/2CF
WPA-80090/4CF
WPA-80090/6CF
WPA-80090/8CF


26799997 Standard WPA
Mounting Bracket
Kit for:

WPA-800120/6CF











R
W
A
A
N
T
E
N
N
A
36210002 Top View Side View
26799997 Top View Side View
*Both the downtilt bracket kit and the
standard mounting bracket kit must be
ordered for mechanical downtilt applications,
except with the WPA-800120/6CF.

**The downtilt bracket kit for the
WPA-800120/6CF includes the standard
mounting bracket.


Mounting Bracket Kits are sold separately
and not included in the price of antennas.
1300 Capital Drive Rockford, IL 61109 Toll-Free (888) 417-9562 Tel. (815) 399-0001
Fax. (815) 399-0156 Email: antel@antelinc.com www.antelinc.com

Mount i ng & Dow nt i l t Br ac k et Ki t s
WPA Br ac ket Ki t s
Part Number Bracket Type

36211102 Standard WPA
*Downtilt Bracket
Kit for:

WPA-80063/2CF
WPA-80080/2CF
WPA-80090/2CF


36114003 Standard WPA
*Downtilt Bracket
Kit for:

WPA-80063/4CF
WPA-80063/6CF
WPA-80063/8CF
WPA-80080/4CF
WPA-80080/6CF
WPA-80080/8CF
WPA-80090/4CF
WPA-80090/6CF
WPA-80090/8CF


26799999 Standard WPA
**Downtilt Bracket
Kit for:

WPA-800120/6CF






*Both the downtilt bracket kit and the
standard mounting bracket kit must be
ordered for mechanical downtilt applications,
except with the WPA-800120/6CF.

**The downtilt bracket kit for the
WPA-800120/6CF includes the standard
mounting bracket.


Mounting Bracket Kits are sold separately
and not included in the price of antennas.




R
W
A
A
N
T
E
N
N
A
36211102 Top View Side View




R
W
A
A
N
T
E
N
N
A
36114003 Top View Side View
26799999 Top View Side View
Vertically Polarized Directional Panel Antennas
806-900 MHz, 824-896 MHz, 806-960 MHz
Model Number
Frequency Range
(MHz)
H-Plane E-Plane
Gain
(dBd)
Fixed Electrical Downtilt
Options**
Length x Width x Depth
(in inches)
RWA-80020/17 _ 806-960 MHz 20 14 17 dBd 1.25 48.2 x 34.4 x 4.0
RWA-80020/20 _ 806-960 MHz 20 7 20 dBd 1.25 100.9 x 34.4 x 4.0
RWA-8008 _ 806-960 MHz 62 56 8 dBd 0 13.2 x 11.2 x 5.9
RWA-80011 _ 806-960 MHz 62 28 11 dBd 0, 3, 5 25.2 x 11.2 x 5.9
RWA-80014 _ 806-960 MHz 62 14 14 dBd 1.25, 3, 5, 9, 14 48.2 x 11.2 x 5.9
RWB-80015/62CF _ 806-900 MHz 62 10 15 dBd 0 72.6 x 11.2 x 4.6
RWA-80017LS _ 806-941 MHz 62 7 16 dBd 0, 3, 5 96.5 x 11.2 x 5.9
RWA-80017 _ 806-960 MHz 62 7 17 dBd 1.25, 2, 3, 4, 5, 6, 9 96.5 x 11.2 x 5.9
RWA-8007 _ 806-960 MHz 78 56 7 dBd 0 13.2 x 11.2 x 5.9
RWA-80010 _ 806-960 MHz 78 28 10 dBd 0, 5, 9 25.2 x 11.2 x 5.9
RWA-80013 _ 806-960 MHz 78 14 13 dBd 1.25, 3, 5, 6, 9 48.2 x 11.2 x 5.9
RWB-80014/78CF _ 806-900 MHz 80 10 13.5 dBd 1.25 72.6 x 11.2 x 4.6
RWA/RWB-800 Series
The RWA/RWB (Reflector Wall Antenna/Reflector Wall Antenna Subset B) is a cellular sector antenna operating within the 806-900
MHz, 824-896 MHz, and the 806-960 MHz frequency range, with 3 dBd H-Plane angles of 20, 62, 78, 90, 102 and 120. These
are classic panel antennas with fixed electrical downtilt and null fill.
Design and Construction of the RWA/RWB Panel:
RWA/RWB antennas are manufactured with our exclusive 3T Technology, featuring a four channel extrusion running the length of
the antenna; durable brass feedlines that eliminate the need for conventional solder joints; a non-collinear system with access to
every radiating element for broad bandwidth and consistent performance across the entire frequency band; air as insulation for vir-
tually no internal signal loss.
Model Number Guide:
Amphenol Antel, Inc.
Models Currently Available:
RWA-
RWB-
800
800
17
13 / 90
LS CF
CF
E-DIN
E-DIN
5 25%
Null Fill (Referenced only if 20% or more)
Electrical Downtilt
Connector Type
NE is an elongated N connector
E-DIN is an elongated DIN connector
BF refers to a Bottom-Fed connector.
CF refers to a Center-Fed connector.
TF refers to a Top-Fed connector.
LS refers to Lobe Suppression.*
Horizontal Beamwidth
Gain in dBd
Operating Frequency Range
800 =Operates within 806-960 MHz
**Some downtilt models may operate at a different frequency range than that listed. Please consult specification sheet for actual frequency range.
When ordering replace __ with the connector type (NE or E-DIN).
*Not all models featuring lobe suppression will have the LS indicator. Check radiation patterns for lobe suppression.
Model Number
Frequency Range
(MHz)
H-Plane E-Plane
Gain
(dBd)
Fixed Electrical Downtilt
Options**
Length x Width x Depth
(in inches)
RWA-80016LS _ 806-941 MHz 78 7 15 dBd 0, 3 96.5 x 11.2 x 5.9
RWA-80016 _ 806-960 MHz 78 7 16 dBd 1.25, 3, 5 96.5 x 11.2 x 5.9
RWB-8006/90 _ 806-960 MHz 90 56 6.5 dBd 0 13.2 x 11.2 x 5.9
RWB-8009/90 _ 806-960 MHz 90 28 9.5 dBd 0 25.2 x 11.2 x 5.9
RWB-80012/90 _ 806-960 MHz 90 14 12.5 dBd 1.25, 3, 5, 6, 9 48.2 x 11.2 x 5.9
RWB-80013/90CF _ 806-900 MHz 90 10 13 dBd 1.25 72.6 x 11.2 x 4.6
RWB-80015/90LS _ 806-941 MHz 90 7 14 dBd 0 96.5 x 11.2 x 5.9
RWB-80015/90 _ 806-960 MHz 90 7 15 dBd 1.25, 3, 5 96.5 x 11.2 x 5.9
RWA-8006 _ 806-960 MHz 102 56 6 dBd 0 13.2 x 11.2 x 5.9
RWA-8009 _ 806-960 MHz 102 28 9 dBd 0, 5, 9 25.2 x 11.2 x 5.9
RWA-80012 _ 806-960 MHz 102 14 12 dBd 1.25, 3, 5, 6, 9 48.2 x 11.2 x 5.9
RWB-80013/102CF _ 806-900 MHz 102 10 12.5 dBd 1.25 72.6 x 11.2 x 4.6
RWA-80015LS _ 806-941 MHz 102 7 14 dBd 0, 3 96.5 x 11.2 x 5.9
RWA-80015 _ 806-960 MHz 102 7 15 dBd 1.25, 2, 3, 5 96.5 x 11.2 x 5.9
RWB-8008/120 _ 806-960 MHz 120 28 8 dBd 0 25.2 x 11.2 x 5.9
RWB-80011/120 _ 806-960 MHz 120 14 11 dBd 1.25, 3, 5, 6, 9 48.2 x 11.2 x 5.9
RWB-80014/120LS _ 806-941 MHz 120 7 13 dBd 0 96.5 x 11.2 x 5.9
RWB-80014/120 _ 806-960 MHz 120 7 14 dBd 1.25, 3, 5 96.5 x 11.2 x 5.9
Models Currently Available Continued:
RWA/RWB-800 Series Continued
Amphenol Antel, Inc.
**Some downtilt models may operate at a different frequency range than that listed. Please consult specification sheet for actual frequency range.
When ordering replace __ with the connector type (NE or E-DIN).
Ver t i c al l y Pol ar i zed, Panel 20 / 17 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80020/17 __
Revision Date: 1/16/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 875 mm 34.4 in
Depth 100 mm 4.0 in
4)
Weight 29 kg 64 lbs
Wind Area
1.06 m
2
11.38 ft
2
Wind load
at 50 m/s
1892 N 425.4 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit included.
Cannot be mechanically downtilted.
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.5:1
Polarization Vertical
1)
Gain 17 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 20
E-Plane 14
1)
Electrical Downtilt 1.25
1)
Null Fill 5%
Lightning Protection Direct Ground
Antenna consists of three separate
RWA-80014 antennas connected by
a power divider.
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 20 / 20 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80020/20 __
Revision Date: 1/16/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2563 mm 100.9 in
Width 875 mm 34.4 in
Depth 100 mm 4.0 in
4)
Weight 44 kg 98 lbs
Wind Area
2.24 m
2
24.1 ft
2
Wind load
at 50 m/s
3800 N 854 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit included.
Cannot be mechanically downtilted.
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.5:1
Polarization Vertical
1)
Gain 20 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 20
E-Plane 7
1)
Electrical Downtilt 1.25
1)
Null Fill 5%
Lightning Protection Direct Ground
Antenna consists of three separate
RWA-80017 antennas connected by
a power divider.
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 62 / 8 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-8008 __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 335 mm 13.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 2.4 kg 5.3 lbs
Wind Area
Fore/Aft 0.10 m
2
1.02 ft
2
Side 0.05 m
2
0.54 ft
2
Rated Wind Velocity (Safety factor 2.0)
>750 km/hr >466 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 135 N 30.2 lbs
Side 71 N 16.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210001
Downtilt bracket kit #36211101
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 8 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 56
1)
Electrical Downtilt 0
1)
Null Fill 0%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 62 / 11 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80011 __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 640 mm 25.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 3.8 kg 8.4 lbs
Wind Area
Fore/Aft 0.18 m
2
1.96 ft
2
Side 0.10 m
2
1.03 ft
2
Rated Wind Velocity (Safety factor 2.0)
>761 km/hr >473 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 258 N 58.1 lbs
Side 137 N 30.9 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36211102
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 11 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 28
1)
Electrical Downtilt 0
1)
Null Fill 0%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 62 / 11 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80011 __ 3
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 640 mm 25.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 3.8 kg 8.4 lbs
Wind Area
Fore/Aft 0.18 m
2
1.96 ft
2
Side 0.10 m
2
1.03 ft
2
Rated Wind Velocity (Safety factor 2.0)
>761 km/hr >473 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 258 N 58.1 lbs
Side 137 N 30.9 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36211102
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 11 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 28
1)
Electrical Downtilt 3
1)
Null Fill 0%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 62 / 11 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80011 __ 5
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 640 mm 25.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 3.8 kg 8.4 lbs
Wind Area
Fore/Aft 0.18 m
2
1.96 ft
2
Side 0.10 m
2
1.03 ft
2
Rated Wind Velocity (Safety factor 2.0)
>761 km/hr >473 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 258 N 58.1 lbs
Side 137 N 30.9 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36211102
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 11 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 28
1)
Electrical Downtilt 5
1)
Null Fill 0%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 62 / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80014 __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
center, or top
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 14 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 14
1)
Electrical Downtilt 1.25
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Ant enna can be or der ed wi t h bot t om-f ed,
cent er -f ed or t op-f ed connect or.
Bot t om-f ed: RWA-80014 + (NE or E-DIN)
Cent er -f ed: RWA-80014CF + (NE or E-DIN)
Top-f ed: RWA-80014TF + (NE or E-DIN)
Ver t i c al l y Pol ar i zed, Panel 62 / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80014CF __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center,
top or bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 14 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 14
1)
Electrical Downtilt 1.25
1)
Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Ant enna can be or der ed wi t h cent er -f ed
bot t om-f ed, or t op-f ed connect or.
Cent er -f ed: RWA-80014CF + (NE or E-DIN)
Bot t om-f ed: RWA-80014 + (NE or E-DIN)
Top-f ed: RWA-80014TF + (NE or E-DIN)
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Ver t i c al l y Pol ar i zed, Panel 62 / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80014TF __
Revision Date: 1/16/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s)
NE or E-DIN
1 port / top,
center or bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 14 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 14
1)
Electrical Downtilt 1.25
1)
Null Fill 5%
Lightning Protection Direct Ground
TF Denotes a Top-Fed
Connector.
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Ant enna can be or der ed wi t h t op-f ed,
cent er -f ed, or bot t om-f ed connect or.
Top-f ed: RWA-80014TF + (NE or E-DIN)
Cent er -f ed: RWA-80014CF + (NE or E-DIN)
Bot t om-f ed: RWA-80014 + (NE or E-DIN)
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Ver t i c al l y Pol ar i zed, Panel 62 / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80014 __ 3
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
or center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 14 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 14
1)
Electrical Downtilt 3
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Ant enna can be or der ed wi t h bot t om-f ed or
cent er -f ed connect or.
Bot t om-f ed: RWA-80014 + (NE or E-DIN) + 3
Cent er -f ed: RWA-80014CF + (NE or E-DIN) + 3
Ver t i c al l y Pol ar i zed, Panel 62 / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80014CF __ 3
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center or
bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 14 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 14
1)
Electrical Downtilt 3
1)
Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Ant enna can be or der ed wi t h cent er -f ed or
bot t om-f ed connect or.
Cent er -f ed: RWA-80014CF + (NE or E-DIN) 3
Bot t om-f ed: RWA-80014 + (NE or E-DIN) 3
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Ver t i c al l y Pol ar i zed, Panel 62 / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80014 __ 3 25%
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 14 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 14
1)
Electrical Downtilt 3
1)
Null Fill 25%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Ant enna avai l abl e wi t h bot t om-f ed
connect or onl y.
Ver t i c al l y Pol ar i zed, Panel 62 / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80014 __ 5
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
or center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 14 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 14
1)
Electrical Downtilt 5
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Ant enna can be or der ed wi t h bot t om-f ed or
cent er -f ed connect or.
Bot t om-f ed: RWA-80014 + (NE or E-DIN) + 5
Cent er -f ed: RWA-80014CF + (NE or E-DIN) + 5
Ver t i c al l y Pol ar i zed, Panel 62 / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80014CF __ 5
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center or
bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 14 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 14
1)
Electrical Downtilt 5
1)
Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Ant enna can be or der ed wi t h cent er -f ed or
bot t om-f ed connect or.
Cent er -f ed: RWA-80014CF + (NE or E-DIN) 5
Bot t om-f ed: RWA-80014 + (NE or E-DIN) 5
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Ver t i c al l y Pol ar i zed, Panel 62 / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80014 __ 9
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
or center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 14 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 14
1)
Electrical Downtilt 9
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Ant enna can be or der ed wi t h bot t om-f ed or
cent er -f ed connect or.
Bot t om-f ed: RWA-80014 + (NE or E-DIN) + 9
Cent er -f ed: RWA-80014CF + (NE or E-DIN) + 9
Ver t i c al l y Pol ar i zed, Panel 62 / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80014CF __ 9
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center or
bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 14 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 14
1)
Electrical Downtilt 9
1)
Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Ant enna can be or der ed wi t h cent er -f ed or
bot t om-f ed connect or.
Cent er -f ed: RWA-80014CF + (NE or E-DIN) 9
Bot t om-f ed: RWA-80014 + (NE or E-DIN) 9
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Ver t i c al l y Pol ar i zed, Panel 62 / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80014 __ 14
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
824-896 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 824-896 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 14 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 14
1)
Electrical Downtilt 14
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Ant enna avai l abl e wi t h bot t om-f ed connect or
onl y.
Ver t i c al l y Pol ar i zed, Panel 62 / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80015/62CF __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Specially designed for
enhanced upper side
lobe suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1844 mm 72.6 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
116
156
mm
mm
4.6
6.1
in
in
4)
Weight 10 kg 23.0 lbs
Wind Area
Fore/Aft 0.53 m
2
5.7 ft
2
Side 0.21 m
2
2.3 ft
2
Rated Wind Velocity (Safety factor 2.0)
>277 km/hr >172 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 765 N 172 lbs
Side 366 N 82 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 15 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 10
1)
Electrical Downtilt 0
1)
Null Fill 15%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed connector
only.
Ver t i c al l y Pol ar i zed, Panel 62 / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80017LS __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Specially designed for
enhanced upper side lobe
suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
or center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 16 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 7
1)
Electrical Downtilt 0
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna can be ordered with bottom-fed or
center-fed connector.
Bottom-fed: RWA-80017LS + (NE or E-DIN)
Center-fed: RWA-80017LSCF + (NE or E-DIN)
Ver t i c al l y Pol ar i zed, Panel 62 / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80017LSCF __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Specially designed for
enhanced upper side lobe
suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center or
bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 16 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 7
1)
Electrical Downtilt 0
1)
Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna can be ordered with center-fed or
bottom-fed connector.
Center-fed: RWA-80017LSCF + (NE or E-DIN)
Bottom-fed: RWA-80017LS + (NE or E-DIN)
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Ver t i c al l y Pol ar i zed, Panel 62 / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80017LS __ 3 25%
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Specially designed for
enhanced upper side lobe
suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 16 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 7
1)
Electrical Downtilt 3
1)
Null Fill 25%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 62 / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80017LS __ 5 25%
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Specially designed for
enhanced upper side lobe
suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 16 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 7
1)
Electrical Downtilt 5
1)
Null Fill 25%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 62 / 17 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80017 __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
or center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 17 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 7
1)
Electrical Downtilt 1.25
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna can be ordered with bottom-fed or
center-fed connector.
Bottom-fed: RWA-80017 + (NE or E-DIN)
Center-fed: RWA-80017CF + (NE or E-DIN)
Ver t i c al l y Pol ar i zed, Panel 62 / 17 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80017CF __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center or
bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 17 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 7
1)
Electrical Downtilt 1.25
1)
Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna can be ordered with center-fed or bot-
tom-fed connector.
Center-fed: RWA-80017CF + (NE or E-DIN)
Bottom-fed: RWA-80017 + (NE or E-DIN)
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142 lbs
Ver t i c al l y Pol ar i zed, Panel 62 / 17 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80017 __ 25%
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s)
NE or E-DIN
1 port / bottom
or center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 17 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 7
1)
Electrical Downtilt 1.25
1)
Null Fill 25%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna can be ordered with bottom-fed or
center-fed connector.
Bottom-fed: RWA-80017 + (NE or E-DIN) + 25%
Center-fed: RWA-80017CF + (NE or E-DIN) + 25%
Ver t i c al l y Pol ar i zed, Panel 62 / 17 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80017CF __ 25%
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center or
bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 17 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 7
1)
Electrical Downtilt 1.25
1)
Null Fill 25%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna can be ordered with center-fed or
bottom-fed connector.
Center-fed: RWA-80017CF + (NE or E-DIN) + 25%
Bottom-fed: RWA-80017 + (NE or E-DIN) + 25%
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142 lbs
Ver t i c al l y Pol ar i zed, Panel 62 / 17 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80017 __ 2
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s)
NE or E-DIN
1 port / bottom
or center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 17 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 7
1)
Electrical Downtilt 2
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna can be ordered with bottom-fed or
center-fed connector.
Bottom-fed: RWA-80017 + (NE or E-DIN) + 2
Center-fed: RWA-80017CF + (NE or E-DIN) + 2
Ver t i c al l y Pol ar i zed, Panel 62 / 17 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80017CF __ 2
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center or
bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 17 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 7
1)
Electrical Downtilt 2
1)
Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna can be ordered with center-fed or bot-
tom-fed connector.
Center-fed: RWA-80017CF + (NE or E-DIN) + 2
Bottom-fed: RWA-80017 + (NE or E-DIN) + 2
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142 lbs
Ver t i c al l y Pol ar i zed, Panel 62 / 17 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80017 __ 3
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 17 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 7
1)
Electrical Downtilt 3
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 62 / 17 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80017 __ 3 25%
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 17 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 7
1)
Electrical Downtilt 3
1)
Null Fill 25%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 62 / 17 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80017 __ 4
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 17 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 7
1)
Electrical Downtilt 4
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 62 / 17 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80017 __ 5
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 17 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 7
1)
Electrical Downtilt 5
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 62 / 17 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80017 __ 5 25%
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 17 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 7
1)
Electrical Downtilt 5
1)
Null Fill 25%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 62 / 17 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80017 __ 6
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 17 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 7
1)
Electrical Downtilt 6
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 62 / 17 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80017 __ 9
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
824-896 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 824-896 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 17 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 62
E-Plane 7
1)
Electrical Downtilt 9
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 78 / 7 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-8007 __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 335 mm 13.2 in
Width 285 mm 11.2 in
Depth
Depth with z- bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 2.4 kg 5.3 lbs
Wind Area
Fore/Aft 0.10 m
2
1.02 ft
2
Side 0.05 m
2
0.54 ft
2
Rated Wind Velocity (Safety factor 2.0)
>750 km/hr >466 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 135 N 30.2 lbs
Side 71 N 16.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210001
Downtilt bracket kit #36211101
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 7 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 78
E-Plane 56
1)
Electrical Downtilt 0
1)
Null Fill 0%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 78 / 10 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80010 __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 640 mm 25.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 3.8 kg 8.4 lbs
Wind Area
Fore/Aft 0.18 m
2
1.96 ft
2
Side 0.10 m
2
1.03 ft
2
Rated Wind Velocity (Safety factor 2.0)
>761 km/hr >473 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 258 N 58.1 lbs
Side 137 N 30.9 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36211102
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 10 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 78
E-Plane 28
1)
Electrical Downtilt 0
1)
Null Fill 0%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 78 / 10 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80010 __ 5
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 640 mm 25.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 3.8 kg 8.4 lbs
Wind Area
Fore/Aft 0.18 m
2
1.96 ft
2
Side 0.10 m
2
1.03 ft
2
Rated Wind Velocity (Safety factor 2.0)
>761 km/hr >473 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 258 N 58.1 lbs
Side 137 N 30.9 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36211102
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 10 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 78
E-Plane 28
1)
Electrical Downtilt 5
1)
Null Fill 0%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 78 / 10 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80010 __ 9
Revision Date: 12/7/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mec hani c al spec i f i c at i ons
Length 640 mm 25.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 3.8 kg 8.4 lbs
Wind Area
Fore/Aft 0.18 m
2
1.96 ft
2
Side 0.10 m
2
1.03 ft
2
Rated Wind Velocity (Safety factor 2.0)
>761 km/hr >473 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 258 N 58.1 lbs
Side 137 N 30.9 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36211102
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 10 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 78
E-Plane 28
1)
Electrical Downtilt 9
1)
Null Fill 0%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 78 / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80013 __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 13 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 78
E-Plane 14
1)
Electrical Downtilt 1.25
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 78 / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80013 __ 3
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 13 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 78
E-Plane 14
1)
Electrical Downtilt 3
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 78 / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80013 __ 3 25%
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 13 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 78
E-Plane 14
1)
Electrical Downtilt 3
1)
Null Fill 25%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 78 / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80013 __ 5
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 13 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 78
E-Plane 14
1)
Electrical Downtilt 5
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 78 / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80013 __ 6
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 13 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 78
E-Plane 14
1)
Electrical Downtilt 6
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 78 / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80013 __ 9
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 13 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 78
E-Plane 14
1)
Electrical Downtilt 9
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 80 / 13.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80014/78CF __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1844 mm 72.6 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
116
156
mm
mm
4.6
6.1
in
in
4)
Weight 10 kg 23.0 lbs
Wind Area
Fore/Aft 0.53 m
2
5.7 ft
2
Side 0.21 m
2
2.3 ft
2
Rated Wind Velocity (Safety factor 2.0)
>277 km/hr >172 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 765 N 172 lbs
Side 366 N 82 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 13.5 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 80
E-Plane 10
1)
Electrical Downtilt 1.25
1)
Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed connector
only.
Ver t i c al l y Pol ar i zed, Panel 78 / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80016LS __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Specially designed for
enhanced upper side
lobe suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
or center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 15 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 78
E-Plane 7
1)
Electrical Downtilt 0
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna can be ordered with bottom-fed or
center-fed connector.
Bottom-fed: RWA-80016LS + (NE or E-DIN)
Center-fed: RWA-80016LSCF + (NE or E-DIN)
Ver t i c al l y Pol ar i zed, Panel 78 / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80016LSCF __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Specially designed for
enhanced upper side
lobe suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center or
bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 15 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 78
E-Plane 7
1)
Electrical Downtilt 0
1)
Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna can be ordered with center-fed or
bottom-fed connector.
Center-fed: RWA-80016LSCF + (NE or E-DIN)
Bottom-fed: RWA-80016LS + (NE or E-DIN)
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Ver t i c al l y Pol ar i zed, Panel 78 / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80016LS __ 3 25%
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Specially designed for
enhanced upper side
lobe suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 15 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 78
E-Plane 7
1)
Electrical Downtilt 3
1)
Null Fill 25%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 78 / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80016 __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s)
NE or E-DIN
1 port / bottom
or center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 16 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 78
E-Plane 7
1)
Electrical Downtilt 1.25
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna can be ordered with bottom-fed or
center-fed connector.
Bottom-fed: RWA-80016 + (NE or E-DIN)
Center-fed: RWA-80016CF + (NEor E-DIN)
Ver t i c al l y Pol ar i zed, Panel 78 / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80016CF __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s)
NE or E-DIN
1 port / center or
bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 16 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 78
E-Plane 7
1)
Electrical Downtilt 1.25
1)
Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna can be ordered with center-fed or
bottom-fed connector.
Center-fed: RWA-80016CF + (NE or E-DIN)
Bottom-fed: RWA-80016 + (NE or E-DIN)
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Ver t i c al l y Pol ar i zed, Panel 78 / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80016 __ 25%
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 16 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 78
E-Plane 7
1)
Electrical Downtilt 1.25
1)
Null Fill 25%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 78 / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80016 __ 3
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 16 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 78
E-Plane 7
1)
Electrical Downtilt 3
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 78 / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80016 __ 3 25%
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 16 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 78
E-Plane 7
1)
Electrical Downtilt 3
1)
Null Fill 25%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 78 / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80016 __ 5
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 16 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 78
E-Plane 7
1)
Electrical Downtilt 5
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 78 / 16 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80016 __ 5 25%
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 16 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 78
E-Plane 7
1)
Electrical Downtilt 5
1)
Null Fill 25%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 90 / 6.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-8006/90 __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 335 mm 13.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 2.4 kg 5.3 lbs
Wind Area
Fore/Aft 0.10 m
2
1.02 ft
2
Side 0.05 m
2
0.54 ft
2
Rated Wind Velocity (Safety factor 2.0)
>750 km/hr >466 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 135 N 30.2 lbs
Side 71 N 16.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210001
Downtilt bracket kit #36211101
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 6.5 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 90
E-Plane 56
1)
Electrical Downtilt 0
1)
Null Fill 0%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 90 / 9.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-8009/90 __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 640 mm 25.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 3.8 kg 8.4 lbs
Wind Area
Fore/Aft 0.18 m
2
1.96 ft
2
Side 0.10 m
2
1.03 ft
2
Rated Wind Velocity (Safety factor 2.0)
>761 km/hr >473 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 258 N 58.1 lbs
Side 137 N 30.9 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36211102
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 9.5 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 90
E-Plane 28
1)
Electrical Downtilt 0
1)
Null Fill 0%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 90 / 12.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80012/90 __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 12.5 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 90
E-Plane 14
1)
Electrical Downtilt 1.25
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 90 / 12.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80012/90 __ 3
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 12.5 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 90
E-Plane 14
1)
Electrical Downtilt 3
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 90 / 12.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80012/90 __ 3 25%
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 12.5 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 90
E-Plane 14
1)
Electrical Downtilt 3
1)
Null Fill 25%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 90 / 12.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80012/90 __ 5
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 12.5 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 90
E-Plane 14
1)
Electrical Downtilt 5
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 90 / 12.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80012/90 __ 6
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 12.5 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 90
E-Plane 14
1)
Electrical Downtilt 6
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 90 / 12.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80012/90 __ 9
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 12.5 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 90
E-Plane 14
1)
Electrical Downtilt 9
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 90 / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80013/90CF __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Specially designed for
enhanced upper side
lobe suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1844 mm 72.6 in
Width 285 mm 11.2 in
Depth
Depth with z- bracket
116
156
mm
mm
4.6
6.1
in
in
4)
Weight 10 kg 23.0 lbs
Wind Area
Fore/Aft 0.53 m
2
5.7 ft
2
Side 0.21 m
2
2.3 ft
2
Rated Wind Velocity (Safety factor 2.0)
>277 km/hr >172 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 765 N 172 lbs
Side 366 N 82 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 13 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 90
E-Plane 10
1)
Electrical Downtilt 1.25
1)
Null Fill 10-15%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed connector
only.
Ver t i c al l y Pol ar i zed, Panel 90 / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80015/90LS __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Specially designed for
enhanced upper side
lobe suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
or center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 14 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 90
E-Plane 7
1)
Electrical Downtilt 0
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna available with bottom-fed or
center-fed connector.
Bottom-fed: RWB-80015/90LS + (NE or E-DIN)
Center-fed: RWB-80015/90LSCF + (NE or E-DIN)
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Ver t i c al l y Pol ar i zed, Panel 90 / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80015/90LSCF __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Specially designed for
enhanced upper side
lobe suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center or
bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 14 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 90
E-Plane 7
1)
Electrical Downtilt 0
1)
Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna available with center-fed or
bottom-fed connector.
Center-fed: RWB-80015/90LSCF + (NE or E-DIN)
Bottom-fed: RWB-80015/90LS + (NE or E-DIN)
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Ver t i c al l y Pol ar i zed, Panel 90 / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80015/90 __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s)
NE or E-DIN
1 port / bottom
or center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 15 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 90
E-Plane 7
1)
Electrical Downtilt 1.25
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna can be ordered with bottom-fed or
center-fed connector.
Bottom-fed: RWB-80015/90 + (NE or E-DIN)
Center-fed: RWB-80015/90CF + (NE or E-DIN)
Ver t i c al l y Pol ar i zed, Panel 90 / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80015/90CF __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s)
NE or E-DIN
1 port / center or
bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 15 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 90
E-Plane 7
1)
Electrical Downtilt 1.25
1)
Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna can be ordered with center-fed or
bottom-fed connector.
Center-fed: RWB-80015/90CF + (NE or E-DIN)
Bottom-fed: RWB-80015/90 + (NE or E-DIN)
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Ver t i c al l y Pol ar i zed, Panel 90 / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80015/90 __ 25%
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s)
NE or E-DIN
1 port / bottom
or center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 15 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 90
E-Plane 7
1)
Electrical Downtilt 1.25
1)
Null Fill 25%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna can be ordered with bottom-fed or
center-fed connector.
Bottom-fed: RWB-80015/90 + (NE or E-DIN) + 25%
Center-fed: RWB-80015/90CF + (NE or E-DIN) + 25%
Ver t i c al l y Pol ar i zed, Panel 90 / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80015/90CF __ 25%
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s)
NE or E-DIN
1 port / center or
bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 15 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 90
E-Plane 7
1)
Electrical Downtilt 1.25
1)
Null Fill 25%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna can be ordered with center-fed or
bottom-fed connector.
Center-fed: RWB-80015/90CF + (NE or E-DIN) + 25%
Bottom-fed: RWB-80015/90 + (NE or E-DIN) + 25%
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Ver t i c al l y Pol ar i zed, Panel 90 / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80015/90 __ 3
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s)
NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 15 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 90
E-Plane 7
1)
Electrical Downtilt 3
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 90 / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80015/90 __ 3 25%
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s)
NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 15 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 90
E-Plane 7
1)
Electrical Downtilt 3
1)
Null Fill 25%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 90 / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80015/90 __ 5
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s)
NE or E-DIN
1 port / bottom
or center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 15 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 90
E-Plane 7
1)
Electrical Downtilt 5
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna can be ordered with bottom-fed or
center-fed connector.
Bottom-fed: RWB-80015/90 + (NE or E-DIN) + 5
Center-fed: RWB-80015/90CF + (NE or E-DIN) + 5
Ver t i c al l y Pol ar i zed, Panel 90 / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80015/90CF __ 5
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s)
NE or E-DIN
1 port / center or
bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 15 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 90
E-Plane 7
1)
Electrical Downtilt 5
1)
Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna can be ordered with center-fed or
bottom-fed connector.
Center-fed: RWB-80015/90CF + (NE or E-DIN) + 5
Bottom-fed: RWB-80015/90 + (NE or E-DIN) + 5
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Ver t i c al l y Pol ar i zed, Panel 90 / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80015/90 __ 5 25%
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s)
NE or E-DIN
1 port / bottom
or center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 15 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 90
E-Plane 7
1)
Electrical Downtilt 5
1)
Null Fill 25%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna can be ordered with bottom-fed or
center-fed connector.
Bottom-fed: RWB-80015/90 + (NE or E-DIN) + 5 25%
Center-fed: RWB-80015/90CF + (NE or E-DIN) + 5 25%
Ver t i c al l y Pol ar i zed, Panel 90 / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80015/90CF __ 5 25%
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s)
NE or E-DIN
1 port / center or
bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 15 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 90
E-Plane 7
1)
Electrical Downtilt 5
1)
Null Fill 25%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna can be ordered with center-fed or
bottom-fed connector.
Center-fed: RWB-80015/90CF + (NE or E-DIN) + 5 25%
Bottom-fed: RWB-80015/90 + (NE or E-DIN) + 5 25%
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Ver t i c al l y Pol ar i zed, Panel 102 / 6 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-8006 __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 335 mm 13.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 2.4 kg 5.3 lbs
Wind Area
Fore/Aft 0.10 m
2
1.02 ft
2
Side 0.05 m
2
0.54 ft
2
Rated Wind Velocity (Safety factor 2.0)
>750 km/hr >466 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 135 N 30.2 lbs
Side 71 N 16.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210001
Downtilt bracket kit #36211101
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 6 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 102
E-Plane 56
1)
Electrical Downtilt 0
1)
Null Fill 0%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 102 / 9 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-8009 __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 640 mm 25.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 3.8 kg 8.4 lbs
Wind Area
Fore/Aft 0.18 m
2
1.94 ft
2
Side 0.10 m
2
1.03 ft
2
Rated Wind Velocity (Safety factor 2.0)
>761 km/hr >473 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 258 N 58.1 lbs
Side 137 N 30.9 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36211102
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 9 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 102
E-Plane 28
1)
Electrical Downtilt 0
1)
Null Fill 0%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 102 / 9 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-8009 __ 5
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 640 mm 25.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 3.8 kg 8.4 lbs
Wind Area
Fore/Aft 0.18 m
2
1.94 ft
2
Side 0.10 m
2
1.03 ft
2
Rated Wind Velocity (Safety factor 2.0)
>761 km/hr >473 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 258 N 58.1 lbs
Side 137 N 30.9 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36211102
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 9 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 102
E-Plane 28
1)
Electrical Downtilt 5
1)
Null Fill 0%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 102 / 9 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-8009 __ 9
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 640 mm 25.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 3.8 kg 8.4 lbs
Wind Area
Fore/Aft 0.18 m
2
1.94 ft
2
Side 0.10 m
2
1.03 ft
2
Rated Wind Velocity (Safety factor 2.0)
>761 km/hr >473 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 258 N 58.1 lbs
Side 137 N 30.9 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36211102
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 9 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 102
E-Plane 28
1)
Electrical Downtilt 9
1)
Null Fill 0%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 102 / 12 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80012 __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 12 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 102
E-Plane 14
1)
Electrical Downtilt 1.25
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 102 / 12 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80012 __ 3
Revision Date: 7/2/07
When ordering replace ___ with connector type.
Radiation pattern
1)
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 12 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 102
E-Plane 14
1)
Electrical Downtilt 3
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Contact our marketing
department for patterns.
Tel: 815-381-7817
Email: antel@antelinc.com
Ver t i c al l y Pol ar i zed, Panel 102 / 12 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80012 __ 3 25 %
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 12 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 102
E-Plane 14
1)
Electrical Downtilt 3
1)
Null Fill 25%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 102 / 12 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80012 __ 5
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 12 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 102
E-Plane 14
1)
Electrical Downtilt 5
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 102 / 12 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80012 __ 6
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 12 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 102
E-Plane 14
1)
Electrical Downtilt 6
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 102 / 12 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80012 __ 9
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 12 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 102
E-Plane 14
1)
Electrical Downtilt 9
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 102 / 12.5 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80013/102CF __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Specially designed for
enhanced upper side
lobe suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1844 mm 72.6 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
116
156
mm
mm
4.6
6.1
in
in
4)
Weight 10 kg 23.0 lbs
Wind Area
Fore/Aft 0.53 m
2
5.7 ft
2
Side 0.21 m
2
2.3 ft
2
Rated Wind Velocity (Safety factor 2.0)
>277 km/hr >172 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 765 N 172 lbs
Side 366 N 82 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 12.5 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 102
E-Plane 10
1)
Electrical Downtilt 1.25
1)
Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with center-fed connector
only.
Ver t i c al l y Pol ar i zed, Panel 102 / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80015LS __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Specially designed for
enhanced upper side
lobe suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s)
NE or E-DIN
1 port / bottom
or center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 14 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 102
E-Plane 7
1)
Electrical Downtilt 0
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna can be ordered with bottom-fed or
center-fed connector.
Bottom-fed: RWA-80015LS + (NE or E-DIN)
Center-fed: RWA-80015LSCF + (NE or E-DIN)
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Ver t i c al l y Pol ar i zed, Panel 102 / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80015LSCF __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Specially designed for
enhanced upper side
lobe suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s)
NE or E-DIN
1 port / center or
bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 14 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 102
E-Plane 7
1)
Electrical Downtilt 0
1)
Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna can be ordered with center-fed or
bottom-fed connector.
Center-fed: RWA-80015LSCF + (NE or E-DIN)
Bottom-fed: RWA-80015LS + (NE or E-DIN)
Ver t i c al l y Pol ar i zed, Panel 102 / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80015LS __ 3 25%
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Specially designed for
enhanced upper side
lobe suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 14 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 102
E-Plane 7
1)
Electrical Downtilt 3
1)
Null Fill 25%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna available with bottom-fed
connector only.
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Ver t i c al l y Pol ar i zed, Panel 102 / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80015 __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s)
NE or E-DIN
1 port / bottom
or center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 15 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 102
E-Plane 7
1)
Electrical Downtilt 1.25
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna can be ordered with bottom-fed or
center-fed connector.
Bottom-fed: RWA-80015 + (NE or E-DIN)
Center-fed: RWA-80015CF + (NE or E-DIN)
Ver t i c al l y Pol ar i zed, Panel 102 / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80015CF __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s)
NE or E-DIN
1 port / center or
bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 15 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 102
E-Plane 7
1)
Electrical Downtilt 1.25
1)
Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna can be ordered with center-fed or
bottom-fed connector.
Center-fed: RWA-80015CF + (NE or E-DIN)
Bottom-fed: RWA-80015 + (NE or E-DIN)
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Ver t i c al l y Pol ar i zed, Panel 102 / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80015 __ 25%
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
or center
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 14 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 102
E-Plane 7
1)
Electrical Downtilt 1.25
1)
Null Fill 25%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna can be ordered with bottom-fed or cen-
ter-fed connector.
Bottom-fed: RWA-80015 + (NE or E-DIN) + 25%
Center-fed: RWA-80015CF + (NE or E-DIN) + 25%
Ver t i c al l y Pol ar i zed, Panel 102 / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80015CF __ 25%
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s)
NE or E-DIN
1 port / center or
bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 14 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 102
E-Plane 7
1)
Electrical Downtilt 1.25
1)
Null Fill 25%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna can be ordered with center-fed or
bottom-fed connector.
Center-fed: RWA-80015CF + (NE or E-DIN) + 25%
Bottom-fed: RWA-80015 + (NE or E-DIN) + 25%
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Ver t i c al l y Pol ar i zed, Panel 102 / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80015 __ 2
Revision Date: 7/2/07
When ordering replace ___ with connector type.
Radiation pattern
1)
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 15 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 102
E-Plane 7
1)
Electrical Downtilt 2
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Contact our marketing
department for patterns.
Tel: 815-381-7817
Email: antel@antelinc.com
Ver t i c al l y Pol ar i zed, Panel 102 / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80015 __ 3
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 15 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 102
E-Plane 7
1)
Electrical Downtilt 3
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 102 / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80015 __ 3 25%
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 15 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 102
E-Plane 7
1)
Electrical Downtilt 3
1)
Null Fill 25%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 102 / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80015 __ 5
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 15 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 102
E-Plane 7
1)
Electrical Downtilt 5
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 102 / 15 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWA-80015 __ 5 25%
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 15 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 102
E-Plane 7
1)
Electrical Downtilt 5
1)
Null Fill 25%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 120 / 8 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-8008/120 __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 640 mm 25.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 3.8 kg 8.4 lbs
Wind Area
Fore/Aft 0.18 m
2
1.94 ft
2
Side 0.10 m
2
1.03 ft
2
Rated Wind Velocity (Safety factor 2.0)
>761 km/hr >473 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 258 N 58.1 lbs
Side 137 N 30.9 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36211102
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.4:1
Polarization Vertical
1)
Gain 8 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 120
E-Plane 28
1)
Electrical Downtilt 0
1)
Null Fill 0%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 120 / 11 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80011/120 __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.45:1
Polarization Vertical
1)
Gain 11 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 120
E-Plane 14
1)
Electrical Downtilt 1.25
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 120 / 11 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80011/120 __ 3
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.45:1
Polarization Vertical
1)
Gain 11 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 120
E-Plane 14
1)
Electrical Downtilt 3
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 120 / 11 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80011/120 __ 3 25%
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.45:1
Polarization Vertical
1)
Gain 11 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 120
E-Plane 14
1)
Electrical Downtilt 3
1)
Null Fill 25%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 120 / 11 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80011/120 __ 5
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.45:1
Polarization Vertical
1)
Gain 11 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 120
E-Plane 14
1)
Electrical Downtilt 5
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 120 / 11 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80011/120 __ 6
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.45:1
Polarization Vertical
1)
Gain 11 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 120
E-Plane 14
1)
Electrical Downtilt 6
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 120 / 11 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80011/120 __ 9
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
824-896 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 1225 mm 48.2 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 6.5 kg 14.3 lbs
Wind Area
Fore/Aft 0.35 m
2
3.76 ft
2
Side 0.18 m
2
1.98 ft
2
Rated Wind Velocity (Safety factor 2.0)
>380 km/hr >236 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 500 N 112.3 lbs
Side 277 N 62.2 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 824-896 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
1)
VSWR 1.45:1
Polarization Vertical
1)
Gain 11 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 120
E-Plane 14
1)
Electrical Downtilt 9
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna available with bottom-fed
connector only.
Ver t i c al l y Pol ar i zed, Panel 120 / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80014/120LS __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Specially designed for
enhanced upper side
lobe suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
or center
1)
VSWR 1.45:1
Polarization Vertical
1)
Gain 13 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 120
E-Plane 7
1)
Electrical Downtilt 0
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna can be ordered with bottom-fed or
center-fed connector.
Bottom-fed: RWB-80014/120LS + (NE or E-DIN)
Center-fed: RWB-80014/120LSCF + (NE or E-DIN)
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Ver t i c al l y Pol ar i zed, Panel 120 / 13 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80014/120LSCF __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Specially designed for
enhanced upper side
lobe suppression.
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / center or
bottom
1)
VSWR 1.45:1
Polarization Vertical
1)
Gain 13 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 120
E-Plane 7
1)
Electrical Downtilt 0
1)
Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna can be ordered with center-fed or
bottom-fed connector.
Center-fed: RWB-80014/120LSCF + (NE or E-DIN)
Bottom-fed: RWB-80014/120LS + (NE or E-DIN)
Ver t i c al l y Pol ar i zed, Panel 120 / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80014/120 __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-960 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-960 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
or center
1)
VSWR 1.45:1
Polarization Vertical
1)
Gain 14 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 120
E-Plane 7
1)
Electrical Downtilt 1.25
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna can be ordered with bottom-fed or
center-fed connector.
Bottom-Fed: RWB-80014/120 + (NE or E-DIN)
Center-fed: RWB-80014/120CF + (NE or E-DIN)
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Ver t i c al l y Pol ar i zed, Panel 120 / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80014/120CF __
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s)
NE or E-DIN
1 port / center or
bottom
1)
VSWR 1.45:1
Polarization Vertical
1)
Gain 14 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 120
E-Plane 7
1)
Electrical Downtilt 1.25
1)
Null Fill 5%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna can be ordered with center-fed or
bottom-fed connector.
Center-fed: RWB-80014/120CF + (NE or E-DIN)
Bottom-Fed: RWB-80014/120 + (NE or E-DIN)
Ver t i c al l y Pol ar i zed, Panel 120 / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80014/120 __ 25%
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s) NE or E-DIN
1 port / bottom
or center
1)
VSWR 1.45:1
Polarization Vertical
1)
Gain 14 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 120
E-Plane 7
1)
Electrical Downtilt 1.25
1)
Null Fill 25%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna can be ordered with bottom-fed or center-
fed connector.
Bottom-Fed: RWB-80014/120 + (NE or E-DIN) + 25%
Center-fed: RWB-80014/120CF + (NE or E-DIN) + 25%
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Ver t i c al l y Pol ar i zed, Panel 120 / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80014/120CF __ 25%
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-900 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-900 MHz
Impedance 50
3)
Connector(s)
NE or E-DIN
1 port / center or
bottom
1)
VSWR 1.45:1
Polarization Vertical
1)
Gain 14 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 120
E-Plane 7
1)
Electrical Downtilt 1.25
1)
Null Fill 25%
Lightning Protection Direct Ground
CF Denotes a Center-Fed
Connector.
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
Antenna can be ordered with center-fed or
bottom-fed connector.
Center-fed: RWB-80014/120CF + (NE or E-DIN) + 25%
Bottom-Fed: RWB-80014/120 + (NE or E-DIN) + 25%
Ver t i c al l y Pol ar i zed, Panel 120 / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80014/120 __ 3
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s)
NE or E-DIN
1 port / bottom
1)
VSWR 1.45:1
Polarization Vertical
1)
Gain 14 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 120
E-Plane 7
1)
Electrical Downtilt 3
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna available with bottom-fed
connector only.
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Ver t i c al l y Pol ar i zed, Panel 120 / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80014/120 __ 3 25%
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s)
NE or E-DIN
1 port / bottom
1)
VSWR 1.45:1
Polarization Vertical
1)
Gain 14 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 120
E-Plane 7
1)
Electrical Downtilt 3
1)
Null Fill 25%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna available with bottom-fed
connector only.
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Ver t i c al l y Pol ar i zed, Panel 120 / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80014/120 __ 5
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s)
NE or E-DIN
1 port / bottom
1)
VSWR 1.45:1
Polarization Vertical
1)
Gain 14 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 120
E-Plane 7
1)
Electrical Downtilt 5
1)
Null Fill 5%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna available with bottom-fed
connector only.
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Ver t i c al l y Pol ar i zed, Panel 120 / 14 dBd
Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com
RWB-80014/120 __ 5 25%
Revision Date: 7/2/07
When ordering replace ___ with connector type.

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Radiation pattern
1)
Horizontal

0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
-170
-160
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
5 10 15 20 25 30 35
Vertical
Radiation patterns for all antennas are
measured with the antenna mounted on
a fiberglass pole.
Mounting on a metal pole will typically
improve the Front-to-Back ratio.
806-941 MHz
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
This Amphenol Antel antenna is under a five-
year limited warranty for repair or replacement.
Mechani c al spec i f i c at i ons
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome.
Mounting and Downtilting
Mounting brackets attach to a pipe diameter of
50-160 mm (2.0-6.3 in).
Mounting bracket kit #36210002
Downtilt bracket kit #36114003
El ec t r i c al spec i f i c at i ons
1)
Typical values.
2)
Power rating limited by connector only.
3)
NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4)
The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
Frequency Range 806-941 MHz*
Impedance 50
3)
Connector(s)
NE or E-DIN
1 port / bottom
1)
VSWR 1.45:1
Polarization Vertical
1)
Gain 14 dBd
2)
Power Rating 500 W
1)
Half Power Angle
H-Plane 120
E-Plane 7
1)
Electrical Downtilt 5
1)
Null Fill 25%
Lightning Protection Direct Ground
A 1 four-channel extrusion running the
entire length of the antenna for unmatched
strength and rigidity.
Durable brass feedline design that elimi-
nates the need for conventional solder
joints in the signal path.
A non-collinear system with access to
every radiating element for broad band-
width and superior performance.
Air as insulation for virtually no internal
signal loss.
*Also available up to 960 MHz. Consult your sales
director for more information.
Antenna available with bottom-fed
connector only.
Length 2450 mm 96.5 in
Width 285 mm 11.2 in
Depth
Depth with z-bracket
150
190
mm
mm
5.9
7.5
in
in
4)
Weight 14 kg 31.0 lbs
Wind Area
Fore/Aft 0.70 m
2
7.51 ft
2
Side 0.37 m
2
3.96 ft
2
Rated Wind Velocity (Safety factor 2.0)
>188 km/hr >117 mph
Wind Load @ 100 mph (161 km/hr)
Fore/Aft 1160 N 238.2 lbs
Side 632 N 142.0 lbs
Part Number Bracket Type

36210001 Standard RWA/RWB
Mounting Bracket
Kit for:

RWA-8006
RWA-8007
RWA-8008
RWB-8006/90

36210002 Standard RWA/RWB
Mounting Bracket
Kit for:

RWA-8009
RWA-80010
RWA-80011
RWA-80012
RWA-80013
RWA-80014
RWA-80014CF
RWA-80015
RWA-80015CF
RWA-80015LS
RWA-80015LSCF
RWA-80016
RWA-80016CF
RWA-80016LS
RWA-80016LSCF
RWA-80017
RWA-80017CF
RWA-80017LS
RWA-80017LSCF
RWB-8008/120
RWB-8009/90
RWB-80011/120
RWB-80012/90
RWB-80013/90CF
RWB-80013/102CF
RWB-80014/78CF
RWB-80014/120
RWB-80014/120CF
RWB-80014/120LS
RWB-80014/120LSCF
RWB-80015/62CF
RWB-80015/90
RWB-80015/90CF
RWB-80015/90LS
RWB-80015/90LSCF

1300 Capital Drive Rockford, IL 61109 Toll-Free (888) 417-9562 Tel. (815) 399-0001
Fax. (815) 399-0156 Email: antel@antelinc.com www.antelinc.com

Mount i ng & Dow nt i l t Br ac k et Ki t s
RWA/RWB Br ac ket Ki t s
*Both the downtilt bracket kit and the
standard mounting bracket kit must be
ordered for mechanical downtilt applications.


Mounting Bracket Kits are sold separately
and not included in the price of antennas.




R
W
A
A
N
T
E
N
N
A
36210002 Top View Side View




R
W
A
A
N
T
E
N
N
A
Side View
1300 Capital Drive Rockford, IL 61109 Toll-Free (888) 417-9562 Tel. (815) 399-0001
Fax. (815) 399-0156 Email: antel@antelinc.com www.antelinc.com

Mount i ng & Dow nt i l t Br ac k et Ki t s
RWA/RWB Br ac ket Ki t s
*Both the downtilt bracket kit and the
standard mounting bracket kit must be
ordered for mechanical downtilt applications.


Mounting Bracket Kits are sold separately
and not included in the price of antennas.
36211101 Top View Side View




R
W
A
A
N
T
E
N
N
A
36211102 Top View Side View
36114003 Top View Side View
Part Number Bracket Type

36211101 *Downtilt Bracket
Kit for:
RWA-8006
RWA-8007
RWA-8008
RWB-8006/90

36211102 *Downtilt Bracket
Kit for:
RWA-8009
RWA-80010
RWA-80011
RWB-8008/120
RWB-8009/90

36114003 *Downtilt Bracket
Kit for:
RWA-80012
RWA-80013
RWA-80014
RWA-80014CF
RWA-80015
RWA-80015CF
RWA-80015LS
RWA-80015LSCF
RWA-80016
RWA-80016CF
RWA-80016LS
RWA-80016LSCF
RWA-80017
RWA-80017CF
RWA-80017LS
RWA-80017LSCF
RWB-80011/120
RWB-80012/90
RWB-80013/90CF
RWB-80013/102CF
RWB-80014/78CF
RWB-80014/120
RWB-80014/120CF
RWB-80014/120LS
RWB-80014/120LSCF
RWB-80015/62CF
RWB-80015/90
RWB-80015/90CF
RWB-80015/90LS
RWB-80015/90LSCF

You might also like