Professional Documents
Culture Documents
: TS08100034-EME
Page 1 of 59
EMC
TEST REPORT
Report Engineer
Julie Wang
Reviewed By
Project Engineer
Table of Contents
1. General information...................................................................................................... 4
1.1 Identification of the EUT........................................................................................ 4
1.2 Additional information about the EUT................................................................... 4
2. Test specifications......................................................................................................... 5
2.1 Test standards.......................................................................................................... 5
2.2 Additions, deviations and exclusions from standards............................................. 5
2.3 Operation mode ...................................................................................................... 5
2.4 Performance criteria ............................................................................................... 6
2.5 Performance verification ........................................................................................ 6
3. Test summary................................................................................................................ 7
4. EN 55022 Conducted emission test.............................................................................. 8
4.1 Operating environment ........................................................................................... 8
4.2 Test setup & procedure ........................................................................................... 8
4.3 Test equipment........................................................................................................ 9
4.4 Emission limit......................................................................................................... 9
4.5 Uncertainty of Conducted Emission....................................................................... 9
4.6 Conducted emission test data ............................................................................... 10
5. EN 55022 Radiated emission test............................................................................... 14
5.1 Operating environment ......................................................................................... 14
5.2 Test setup & procedure ......................................................................................... 14
5.3 Test equipment...................................................................................................... 16
5.4 Emission limit....................................................................................................... 16
5.5 Uncertainty of Radiated Emission........................................................................ 16
5.6 Radiated emission test data .................................................................................. 17
6. EN 61000-3-2 Harmonics test .................................................................................... 21
6.1 Operating environment ......................................................................................... 21
6.2 Test setup & procedure ......................................................................................... 21
6.3 Test equipment...................................................................................................... 21
6.4 Uncertainty of Radiated Emission........................................................................ 21
6.5 Test result.............................................................................................................. 22
7. EN 61000-3-3 Voltage fluctuations-flicker Test......................................................... 24
7.1 Operating environment ......................................................................................... 24
7.2 Test setup & procedure ......................................................................................... 24
7.3 Test equipment...................................................................................................... 24
7.4 Uncertainty of Radiated Emission........................................................................ 24
7.5 Test result.............................................................................................................. 25
8. EN 61000-4-2 Electrostatic discharge immunity test................................................. 27
8.1 Operating environment ......................................................................................... 27
8.2 Purpose ................................................................................................................. 27
8.3 Test set-up............................................................................................................. 27
8.4 Test conditions ...................................................................................................... 27
8.5 Test equipment...................................................................................................... 28
8.6 Test result.............................................................................................................. 28
9. EN 61000-4-3 Radiated, radio-frequency, electromagnetic field immunity test
9.1 Operating environment ......................................................................................... 30
Report No.: TS08100034-EME
Page 3 of 59
1. General information
The EUT is a Digital Wireless Video Baby Monitor, and was defined as information
technology equipment.
2. Test specifications
The EUT was supplied with DC 6V from adapter (230 Vac, 50 Hz) and was tested in
normal operating mode.
Report No.: TS08100034-EME
Page 6 of 59
Performance table
Criteria During test After test
Shall operate as intended Shall operate as intended
May show degradation of Shall be no degradation of performance(Note 2)
A performance(Note1) Shall be no loss of function
Shall be no loss of function Shall be no loss of stored data or user
programmable functions
Shall be no unintentional transmissions
May show loss of function (one or Functions shall be self-recoverable
more) Shall operate as intended after recovering
B May show degradation of performance Shall be no degradation of performance(Note 2)
(Note 1) Shall be no loss of stored data or user
No unintentional transmissions programmable functions
May be loss of function (one or more) Functions shall be recoverable by the operator
C Shall operate as intended after recovering
Shall be no degradation of performance(Note 2)
Note 1: Degradation of performance during the test is understood as a degradation to a level not
below a minimum performance level specified by the manufacturer for the use of the
apparatus as intended. In some cases the specified minimum performance level may be
replaced by a permissible degradation of performance.
If the minimum performance level or the permissible performance degradation is not
specified by the manufacturer then either of these may be derived from the product
description and documentation (including leaflets and advertising) and what the user may
reasonably expect from the apparatus if used as intended.
Note 2: No degradation of performance after the test is understood as no degradation below a
minimum performance level specified by the manufacturer for the use of the apparatus as
intended. In some cases the specified minimum performance level may be replaced by a
permissible degradation of performance. After the test no change of actual operating data
or user retrievable data is allowed.
If the minimum performance level or the permissible performance degradation is not
specified by the manufacturer then either of these may be derived from the product
description and documentation (including leaflets and advertising) and what the user may
reasonably expect from the apparatus if used as intended.
The EUT has been monitored based on manufacturer’s specification, the performance
fulfilled the requirements of standard.
Report No.: TS08100034-EME
Page 7 of 59
3. Test summary
(EN 301 489-17)
Emission
Standard Test Type Result Remarks
Pass by -23.77 dB at 30.000 MHz
Conducted Test PASS
EN 55022: 2006 Line Phase
Class B Pass by -1.84 dB at 528.000 MHz
Radiated Test PASS
With antenna polarization Horizontal
EN 61000-3-2: 2006 Harmonic current
PASS Meet the requirements
Class A Emissions
EN 61000-3-3: 1995 Voltage fluctuation
PASS Meet the requirements
+A1: 2001+A2: 2005 & Flicker
Immunity
Standard Test Type Result Performance Criteria Test Judgment
EN 61000-4-2: 1995 Meets the requirements of
ESD test PASS Criterion B
+A1: 1998+ A2: 2001 Performance Criterion B
EN 61000-4-3: 2006 Meets the requirements of
RS test PASS Criterion A
+A1: 2007 Performance Criterion A
Meets the requirements of
EN 61000-4-4: 2004 EFT test PASS Criterion B
Performance Criterion B
Meets the requirements of
EN 61000-4-5: 2006 Surge test PASS Criterion B
Performance Criterion A
Meets the requirements of
EN 61000-4-6: 2007 CS test PASS Criterion A
Performance Criterion A
Remark:
The EUT has been tested/evaluated and pass the above standards without modification.
Report No.: TS08100034-EME
Page 8 of 59
(1) TTD-41T
wireless
AC Power
AMN 1 TTD-41T
wireless
AMN 2 TTD-61R
EMI
Receiver
AC Power
(2) TTD-61R
wireless
AC Power
AMN 1 TTD-61R
wireless
AMN 2 TTD-41T
EMI
Receiver
AC Power
The EUT along with its peripherals were placed on a 1.0 meter(W)×1.5 meter(L)
and 0.8 meter in height wooden table and the EUT was adjusted to maintain a
0.4meter space from a vertical reference plane. The EUT was connected to power
mains through a Artificial Mains Network (AMN), which provided 50 ohm coupling
impedance for measuring instrument and the chassis ground was bounded to the
horizontal ground plane of shielded room.
The excess power cable between the EUT and the AMN was bundled. All connecting
cables of EUT and peripherals were moved to find the maximum emission
Report No.: TS08100034-EME
Page 9 of 59
0.50~5.00 73 60 56 46
5.00~30.0 73 60 60 50
Phase: Line
Model No.: TTD-41T
Test Condition: Normal operation mode
Remark:
1. Corr. Factor (dB)= AMN Factor (dB) + Cable Loss (dB)
2. Margin (dB) = Level (dBuV) – Limit (dBuV)
Report No.: TS08100034-EME
Page 11 of 59
Phase: Neutral
Model No.: TTD-41T
Test Condition: Normal operation mode
Remark:
1. Corr. Factor (dB)= AMN Factor (dB) + Cable Loss (dB)
2. Margin (dB) = Level (dBuV) – Limit (dBuV)
Report No.: TS08100034-EME
Page 12 of 59
Phase: Line
Model No.: TTD-61R
Test Condition: Normal operation mode
Remark:
1. Corr. Factor (dB)= AMN Factor (dB) + Cable Loss (dB)
2. Margin (dB) = Level (dBuV) – Limit (dBuV)
Report No.: TS08100034-EME
Page 13 of 59
Phase: Neutral
Model No.: TTD-61R
Test Condition: Normal operation mode
Remark:
1. Corr. Factor (dB)= AMN Factor (dB) + Cable Loss (dB)
2. Margin (dB) = Level (dBuV) – Limit (dBuV)
Report No.: TS08100034-EME
Page 14 of 59
The Diagram below shows the test setup, which is utilized to make these measurements.
(1) TTD-41T
Antenna
Tower
1.0~4.0 meter
wireless Receiver
10 meter
Antenna
TTD-41T
0.8 meter
Ground Plane
wireless □
RF Test
TTD-61R Receiver
Report No.: TS08100034-EME
Page 15 of 59
(2) TTD-61R
Antenna
Tower
1.0~4.0 meter
wireless Receiver
10 meter
Antenna
TTD-61R
0.8 meter
Ground Plane
wireless □
RF Test
TTD-41T Receiver
Radiated testing was performed at a 10 meters open area test site. The devices under test
were placed on a turntable top 0.8 meter above ground. The table was 360 degrees to
determine the position of the highest radiation. EUT is set 10 meters from the EMI
receiving antenna, which is mounted on the top of a variable height mast. The antenna
height is varied between one meter and four meters above ground to find the
maximum value of the field strength. Both horizontal polarization and vertical
polarization of the antenna was set to conduct the measurement.
The bandwidth was set on the EMI meter 120 kHz.
The levels are quasi peak value readings. The frequency spectrum from 30 MHz to 1000
MHz was investigated.
Report No.: TS08100034-EME
Page 16 of 59
30~230 10 40 30
230~1000 10 47 37
Note:
1. The tighter limit shall apply at the edge between two frequency bands.
2. Distance refers to the distance in meters between the measuring instrument
antenna and the closet point of EUT.
Polarity: Vertical
Model No.: TTD-41T
Test Condition: Normal operation mode
Remark:
1. Level (dBμV/m)= Factor (dB/m)+ Read Level (dBμV)
2. Factor = Antenna Factor (dB/m) + Cable Loss (dB)
3. Over Limit (Margin) (dB) = Level (dBμV/m) – Limit Line(dBμV/m)
Report No.: TS08100034-EME
Page 18 of 59
Polarity: Horizontal
Model No.: TTD-41T
Test Condition: Normal operation mode
Remark:
1. Level (dBμV/m)= Factor (dB/m)+ Read Level (dBμV)
2. Factor = Antenna Factor (dB/m) + Cable Loss (dB)
3. Over Limit (Margin) (dB) = Level (dBμV/m) – Limit Line(dBμV/m)
Report No.: TS08100034-EME
Page 19 of 59
Polarity: Vertical
Model No.: TTD-61R
Test Condition: Normal operation mode
Remark:
1. Level (dBμV/m)= Factor (dB/m)+ Read Level (dBμV)
2. Factor = Antenna Factor (dB/m) + Cable Loss (dB)
3. Over Limit (Margin) (dB) = Level (dBμV/m) – Limit Line(dBμV/m)
Report No.: TS08100034-EME
Page 20 of 59
Polarity: Horizontal
Model No.: TTD-61R
Test Condition: Normal operation mode
Remark:
1. Level (dBμV/m)= Factor (dB/m)+ Read Level (dBμV)
2. Factor = Antenna Factor (dB/m) + Cable Loss (dB)
3. Over Limit (Margin) (dB) = Level (dBμV/m) – Limit Line(dBμV/m)
Report No.: TS08100034-EME
Page 21 of 59
AC power Measuring
EUT
Equipment
PC controller
Harmonics of the fundamental current were measured up to 2 kHz using a digital power
analyzer. The test voltage was supplied from an AC source, which meets the
requirements according to the standard.
The steady-state harmonic current measurements were carried out using averaging.
Note: The above equipments are within the valid calibration period.
EUT: TTD-41T
Power Freq.: 50Hz
Power Voltage: 230Vac
CLASSIFICATION: CLASS A
SUMMARY RESULT: PASS
Current Current
Hn AMPs Limit
Result Hn AMPs Limit
Result
1 0.023 NA Pass 21 0.000 0.107 Pass
2 0.000 1.080 Pass 22 0.000 0.084 Pass
3 0.008 2.300 Pass 23 0.000 0.098 Pass
4 0.000 0.430 Pass 24 0.000 0.077 Pass
5 0.006 1.140 Pass 25 0.000 0.090 Pass
6 0.000 0.300 Pass 26 0.000 0.071 Pass
7 0.001 0.770 Pass 27 0.000 0.083 Pass
8 0.000 0.230 Pass 28 0.000 0.066 Pass
9 0.001 0.400 Pass 29 0.000 0.078 Pass
10 0.000 0.184 Pass 30 0.000 0.061 Pass
11 0.001 0.330 Pass 31 0.000 0.073 Pass
12 0.000 0.153 Pass 32 0.000 0.058 Pass
13 0.000 0.210 Pass 33 0.000 0.068 Pass
14 0.000 0.131 Pass 34 0.000 0.054 Pass
15 0.000 0.150 Pass 35 0.000 0.064 Pass
16 0.000 0.115 Pass 36 0.000 0.051 Pass
17 0.000 0.132 Pass 37 0.000 0.061 Pass
18 0.000 0.102 Pass 38 0.000 0.048 Pass
19 0.000 0.118 Pass 39 0.000 0.058 Pass
20 0.000 0.092 Pass 40 0.000 0.046 Pass
Report No.: TS08100034-EME
Page 23 of 59
EUT: TTD-61R
Power Freq.: 50Hz
Power Voltage: 230Vac
CLASSIFICATION: CLASS A
SUMMARY RESULT: PASS
Current Current
Hn AMPs Limit
Result Hn AMPs Limit
Result
1 0.023 NA Pass 21 0.000 0.107 Pass
2 0.000 1.080 Pass 22 0.000 0.084 Pass
3 0.008 2.300 Pass 23 0.000 0.098 Pass
4 0.000 0.430 Pass 24 0.000 0.077 Pass
5 0.006 1.140 Pass 25 0.000 0.090 Pass
6 0.000 0.300 Pass 26 0.000 0.071 Pass
7 0.001 0.770 Pass 27 0.000 0.083 Pass
8 0.000 0.230 Pass 28 0.000 0.066 Pass
9 0.001 0.400 Pass 29 0.000 0.078 Pass
10 0.000 0.184 Pass 30 0.000 0.061 Pass
11 0.001 0.330 Pass 31 0.000 0.073 Pass
12 0.000 0.153 Pass 32 0.000 0.058 Pass
13 0.000 0.210 Pass 33 0.000 0.068 Pass
14 0.000 0.131 Pass 34 0.000 0.054 Pass
15 0.000 0.150 Pass 35 0.000 0.064 Pass
16 0.000 0.115 Pass 36 0.000 0.051 Pass
17 0.000 0.132 Pass 37 0.000 0.061 Pass
18 0.000 0.102 Pass 38 0.000 0.048 Pass
19 0.000 0.118 Pass 39 0.000 0.058 Pass
20 0.000 0.092 Pass 40 0.000 0.046 Pass
Report No.: TS08100034-EME
Page 24 of 59
Measuring
AC power EUT
Equipment
PC controller
The voltage changes at the supply terminals were measured using the voltage method.
The test voltage was supplied from an AC source which meets the requirements
according to the standard. The voltage source has virtually zero internal impedance
and is connected
(1 phase)
Z = 0.4 + j 0.25 Ω (total impedance)
(3 phases)
Impedance in line conductor: Za = 0.25 + j 0.25 Ω
Impedance in neutral conductor: Zn = 0.15 +j 0.10 Ω
Note: The above equipments are within the valid calibration period.
EUT: TTD-41T
Power Freq.: 50Hz
Power Voltage: 230Vac
EUT: TTD-61R
Power Freq.: 50Hz
Power Voltage: 230Vac
8.2 Purpose
The object of the test is to evaluate the ESD immunity performance of EUT.
A horizontal coupling plane (HCP) was placed on a non-metallic table 0.8 meter above
a reference ground plane (RGP) and connected to it with a cable with two 470 kΩ
resistors. The EUT was placed on an insulation sheet on the HCP and was operated
according to the specified operating mode.
A vertical coupling plane (VCP) was connected to the RGP with a cable with two 470 k
Ω resistors.
EUT: TTD-41T
Description
Contact Discharge: 2 test points Air Discharge
Metallic Screws Plastic Screws
Metallic Case Plastic Case (gap)
Metallic Connect ports Plastic Connect ports
Metallic Junctions Plastic Junctions
Others: LED indicator
Panel Board
Others:Right/Left side buttons,
Turn/OFF volume buttons
Report No.: TS08100034-EME
Page 29 of 59
EUT: TTD-61R
Description
Contact Discharge: 0 test points Air Discharge
Metallic Screws Plastic Screws
Metallic Case Plastic Case (gap)
Metallic Connect ports Plastic Connect ports
Metallic Junctions Plastic Junctions
Others: LED indicator
Panel Board
Others:Right/Left side buttons,
Turn/OFF volume buttons
Report No.: TS08100034-EME
Page 30 of 59
9.2 Purpose
This test method subjects the EUT to a power source of disturbance comprising electric
and magnetic field, simulating those coming from intentional RF transmitters.
The EUT was placed on a non-metallic table 0.8 meter above the reference ground
plane (RGP) and was operated according to its specified operating mode.
Ferrite tiles/absorbers were placed on the RGP between the EUT and the antenna to
reduce the reflections from the RGP. The EUT and its cables were exposed for the
electromagnetic field for 1.5 meter vertically and 1.5 meter horizontally.
H: Horizontal V: Vertical
EUT: TTD-41T
EUT: TTD-61R
10.2 Purpose
The purpose of this test is to evaluate the EUT performance during the repetitive
transient bursts applied to power port and ports for I/O ports.
For power port testing, the EUT was placed on a non-metallic table 0.1 meter above a
reference ground plane (RGP) and was put into operation according to the specified
operating mode.
Open-circuit output test voltage (±10 %) and repetition rate of the impulses (±20 %)
On I/O (Input/Output) signal,
On power supply port, PE
Data and control ports
Level Voltage peak Repetition rate Voltage peak Repetition rate
kV kHz kV kHz
1 0.5 5 or 100 0.25 5 or 100
2 1 5 or 100 0.5 5 or 100
3 2 5 or 100 1 5 or 100
4 4 5 or 100 2 5 or 100
(1)
X Special Special Special Special
NOTE 1 Use of 5 kHz repetition rates is traditional; however, 100 kHz is closer to reality. Product
committees should determine which frequencies are relevant for specific products or product types.
NOTE 2 With some products, there may be no clear distinction between power ports and I/O ports, in
which case it is up to product committees to make this determination for test purposes.
(1) “x” is an open level. The level has to be specified in the dedicated equipment
specification
EUT: TTD-41T
EUT: TTD-61R
11.2 Purpose
The object of this test is to establish a common reference to evaluate the performance of
EUT when subjected to high-energy disturbances on the power and interconnection
lines.
The EUT was placed on a non-metallic support 0.8 meter above a reference ground
plane and was put into operation according to the specified operating mode.
Note: “X” is an open class. This level can be specified in the product specification
Surge wave form: 1.2 x 50 µs, Repetition rate: 1 /min (max)
Report No.: TS08100034-EME
Page 36 of 59
EUT: TTD-41T
Phase Criteria
0o 90o 180o 270o
Volt Mode Polarity level
+ P P P P A
0.5 kV L1 to L2
- P P P P A
+ P P P P A
1 kV L1 to L2
- P P P P A
+ - - - - -
L1 to Gnd
1 kV/ - - - - - -
2 kV + - - - - -
L2 to Gnd
- - - - - -
Note: 1. “P” means the EUT pass the test.
Note: 2. “-“ means not applicable
EUT: TTD-61R
Phase Criteria
0o 90o 180o 270o
Volt Mode Polarity level
+ P P P P A
0.5 kV L1 to L2
- P P P P A
+ P P P P A
1 kV L1 to L2
- P P P P A
+ - - - - -
L1 to Gnd
1 kV/ - - - - - -
2 kV + - - - - -
L2 to Gnd
- - - - - -
Note: 1. “P” means the EUT pass the test.
Note: 2. “-“ means not applicable
Report No.: TS08100034-EME
Page 37 of 59
12.2 Purpose
The test method subjects the EUT to a power source of disturbance comprising electric
and magnetic field, simulating those coming from intentional RF transmitters.
The measurement is for evaluating the performance of EUT when subjected to RF
conducted disturbance.
The EUT was placed on a non-metallic support 0.1 meter above a reference ground
plane (RGP) with the coupling/decoupling network (CDN) placed 0.3 meter from the
EUT on the RGP.
Voltage
Test level Modulation
(Vrms)
1 1 1 kHz 80 % AM
2 3 1 kHz 80 % AM
3 10 1 kHz 80 % AM
X Special 1 kHz 80 % AM
EUT: TTD-41T
Frequency Criteria
Test Port/Line Result Remark
(MHz) Level
0.15 MHz to 80 MHz Power Line P A -
Note: 1. “P” means the EUT pass the test.
Note: 2. “-“ means not applicable
EUT: TTD-61R
Frequency Criteria
Test Port/Line Result Remark
(MHz) Level
0.15 MHz to 80 MHz Power Line P A -
Note: 1. “P” means the EUT pass the test.
Note: 2. “-“ means not applicable
Report No.: TS08100034-EME
Page 40 of 59
13.2 Purpose
The object of this standard is to establish a common reference for evaluating the
Immunity of electrical and electronic equipment when subjected to voltage dips, Short
interruptions, and voltage variations.
The EUT was placed on a non-metallic support 0.8 meter above a reference ground
plane and was put into operation according to the specified operating mode.
Test Duration
Tests Recovery Time
Level % UT (Period)
0 % Short Circuit 250 3 10 Sec.
0 % Open Circuit 250 3 10 Sec.
EUT: TTD-41T
EUT: TTD-61R
TTD-41T
TTD-41T
Report No.: TS08100034-EME
Page 57 of 59
TTD-61R
TTD-61R
Report No.: TS08100034-EME
Page 58 of 59
TTD-41T
TTD-41T
Report No.: TS08100034-EME
Page 59 of 59
TTD-61R
TTD-61R