Control Systems and Simulation lab Electrical and Electronics engineering Department-BVRIT. Manual uses the plan, cogent and simple language to explain the fundamental aspects of Control Systems and Simulation in practical. Manual prepared very carefully with our level best. It gives all the steps in executing an experiment.
Control Systems and Simulation lab Electrical and Electronics engineering Department-BVRIT. Manual uses the plan, cogent and simple language to explain the fundamental aspects of Control Systems and Simulation in practical. Manual prepared very carefully with our level best. It gives all the steps in executing an experiment.
Control Systems and Simulation lab Electrical and Electronics engineering Department-BVRIT. Manual uses the plan, cogent and simple language to explain the fundamental aspects of Control Systems and Simulation in practical. Manual prepared very carefully with our level best. It gives all the steps in executing an experiment.
DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING
ACADEMIC YEAR 2012-2013 III B.Tech EEE I-SEMESTER
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 2
PREFACE
The significance of the Control Systems and Simulation Lab is renowned in the various fields of engineering applications. For an Electrical Engineer, it is obligatory to have the practical ideas about the Control Systems and Simulation. By this perspective we have introduced a Laboratory manual cum Observation for Control Systems and Simulation Lab.
The manual uses the plan, cogent and simple language to explain the fundamental aspects of Control Systems and Simulation in practical. The manual prepared very carefully with our level best. It gives all the steps in executing an experiment.
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 3
ACKNOWLEDGEMENT
It is one of lifes simple pleasures to say thank you for all the help that one has extended their support. I wish to acknowledge and appreciate Assoc Prof K. Raudu, Assist. Prof. R.Munishwar, Foreman. P Prabhu Dass, and A Ramesh for their sincere efforts made towards developing the Control Systems and Simulation Lab manual. I wish to thank students for their suggestions which are considered while preparing the lab manual. I am extremely indebted to Sri.Col Dr. T. S. Surendra, Principal and Professor, Department of Electrical and Electronics Engineering, BVRIT for his valuable inputs and sincere support to complete the work. Specifically, I am grateful to the Management for their constant advocacy and incitement. Finally, I would again like to thank the entire faculty in the Department and those people who directly or indirectly helped in successful completion of this work.
(Prof. N. BHOOPAL) HOD - EEE
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 4
GUIDELINES TO WRITE YOUR OBSERVATION BOOK
1. Experiment Title, Aim, Apparatus, Procedure should be on right side. 2. Circuit diagrams, Model graphs, Observations table, Calculations table should be left side. 3. Theoretical and model calculations can be any side as per your convenience. 4. Result should always be in the ending. 5. You all are advised to leave sufficient no of pages between experiments for theoretical or model calculations purpose.
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 5
DOS AND DONTS IN THE LAB DOS:- 1. Proper dress has to be maintained while entering in the Lab. (Boys Tuck in and shoes, girls with apron)
2. All students should come to the Lab with necessary tools. (Cutting Pliers 6, Insulation remover and phase tester)
3. Students should carry observation notes and record completed in all aspects. 4. Correct specifications of the equipment have to be mentioned in the circuit diagram. 5. Student should be aware of operating equipment. 6. Students should be at their concerned experiment table, unnecessary moment is restricted. 7. Student should follow the indent procedure to receive and deposit the equipment from the Lab Store Room.
8. After completing the connections Students should verify the circuits by the Lab Instructor. 9. The reading must be shown to the Lecturer In-Charge for verification. 10. Students must ensure that all switches are in the OFF position, all the connections are removed.
11. All patch cords and stools should be placed at their original positions.
DONTs:-
1. Dont come late to the Lab. 2. Dont enter into the Lab with Golden rings, bracelets and bangles. 3. Dont make or remove the connections with power ON. 4. Dont switch ON the supply without verifying by the Staff Member. 5. Dont switch OFF the machine with load. 6. Dont leave the lab without the permission of the Lecturer In-Charge.
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 6 JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD III Year B.Tech. EEE I-Semester L T/P/D C 0 -/3/- 2 (55603)CONTROL SYSTEMS AND SIMULASTION LAB
Any eight of the following experiments are to be conducted
1. Time response of Second order System 2. Characteristics of Synchros 3. Programmable logic controller study and verification of truth tables of Logic Gates, Simple Boolean expressions and application of speed control of motor. 4. Effect of feedback on DC Servo motor. 5. Transfer function of DC motor 6. Effect of P,PD,PI,PID controller on a second order system 7. Lag and lead compensation- magnitude and phase plot. 8. Transfer function of DC generator 9. Temperature controller using PID 10. Characteristics of Magnetic Amplifier 11. Characteristics of AC servo motor
Any two Simulation experiments to be conducted.
1. PSPICE simulation of Op-Amp based integrator and differentiator circuits. 2. Linear system analysis (Time domain analysis, Error analysis) using MATLAB. 3. Stability analysis (Bode, Root Locus, Nyquist) of linear time invariant system using MATLAB. 4. State Space model for classical transfer function using MATLAB verification.
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 7
Control Systems and Simulation Lab
III Year B.Tech EEE I-Sem Academic year 2012-2013
S.no Name of the experiment 1 Time response of Second order System
2 Characteristics of Synchros
3 Effect of P,PD,PI,PID controller on a second order system
4 Temperature controller using PID
5 Characteristics of Magnetic Amplifier
6 DC Position control system
7 Characteristics of AC servo motor
8 Transfer function of DC generator
9 Root locus plot, bode plot from MATLAB
10 Characteristics of DC servo motor 11 Transfer function of DC shunt motor 12 Simulation of State space models using MAT LAB Add on Experiments 1 Simulation of Transfer function using Operational Amplifier
2 Lag lead compensator 3 P L C
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 8
1. TIME RESPONSE OF SECOND ORDER SYSTEM
AIM: To study the time response of second order system with step input and square input.
b) signal source: This signal source consists of a square wave generator of 15Hz approximately and a step signal generator. A switch is provided to select square are step (DC) source. Amplitude of signal source can be varied from 0v to 15v approximately for square wave and 0v to 15v approximately for step (DC) source.
c) Second order system: This part consists of second order system built using op-amp and an RLC circuit. Definition: We can define second order system by using closed transfer function C(S)/R(S)= W n 2 /S 2 +2 W+W n 2
Where is called damping ratio.
SECOND ORDER SYSTEM USING RLC :-
Calculation:
W n = 1/ LC = 1/ 2X.32X10.6=1250
R=2 L/C
FOR =0.3, R=1500 =1, R=5000
=0.7, R= 3500 =2, R=10000
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 9
PROCEDURE: 1. Connections are made as per the circuit diagram. 2. Switch on the main supply to the unit. Observe the source o/p by selecting square wave and by varying amplitude using function generator. 3. First select square wave signal with a required time constant. Draw input square wave. 4. Connect signal output to second order system input using RLC. 5. Draw the graph for the respective output.
Result: Hence the steady state response for the square wave input is verified.
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 10
2. CHARACTERSTICS OF SYNCHROS AND TRANSMITTER
Circuit Diagram:
Study of synchro transmitter: Circuit Diagram :
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 11
2. CHARACTERSTICS OF SYNCHROS AND TRANSMITTER
Aim: To study the characteristics of synchros as transmitter and synchro transmitter- receiver pair.
Apparatus: Synchros pair unit Voltmeter (0-50v) MI-3No.s 1-Ph variac patch cords. Definition: A synchros on electromagnetic transducer commonly used convert an angular position of a shaft into an electric signal.
Study of Synchro Transmitter and receiver:- In this part or experiment we can see that because or the transformer action the angular position of rotor is transformed into a unique set of stator voltages.
PROCEDURE:
1) Make the connections as per CKT diagram. 2) Apply 50v AC supply to the transmitter. 3) Adjust the pointer on the rotor of the transmitters to zero position 4) Observe the position across to rotate of the receiver. If it is not zero the rotor, so as to obtain zero voltage and this value is referred to as electrical zero position of the receiver. 5) Holding firm by position of rotor shaft at transmitters slightly. Note down the voltage across the rotor of the receiver. 6) Now continue the readings up to 360 , in steps of 30 by increasing the angular positions of the transmitter in steps. 7) Take rotor shaft position of transmitters on X- axis and voltage on Y axis and draw a graph. 8) Draw graph by taking transmitter angular position on X- axis and receiver angular position on Y axis.
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 12
Table:
S.No Rotor angle of
Transmitter
Rotor angle of receiver
Receiver rotor voltage
Study of synchro transmitter: Procedure:- 1) Apply 50V,AC to the rotor of synchro transmitter. 2) Measure the voltage between s 1 , s2,s3
for various shaft positions from 0-3600.There voltage which have to be ve sign has to be desired form the knowledge of voltage between wave forms. 3) Similarly measure the voltage between S 2 and S 3 , S 3 and S 1 various shaft positions. 4) Plot the graph of rotor position in degrees Vs (S 1, S 2 ),(S 2, S 3 ) and (S 3, S 1 ) respectively.
Result: Hence the characteristics of Synchros are verified
Questions: 1) Define synchros? 2) What do you understood by this experiment? 3) Write principal how angular position is converted to voltage? 4) Write the applications of synchro transmitter? 5) Write the applications of synschro receiver? S.NO Voltage ROTOR POSITION SHAFT V(S 1 -S3) V(S 2 -S 3 ) V(S 3 -S 4 )
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 13 3. Effect of P, PD, PI, PID Controller on a second order system
b) Integral Controller-Open loop :
Diagram of the system:
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 14
3. Effect of P, PD, PI, PID Controller on a second order system
AIM :To study the effect of P,PD,PI,PID controller on a second order system.
APPARATUS:- PID controller unit, patch cords and CRO.
PID controller unit:-
Front panel details:-
1) Main : Main on/off switch 2) Square : Variable square wave out 0-2v. 3) Level : Potentio meter to vary the amplitude of square wave and triangular wave 4) Frequency : Potentio meter to vary the frequency of square wave and triangular wave 5) Triangle : Triangle wave O/P for triggering purpose in x-y mode 6) Amplitude : Potentio meter to vary the D.C voltage from 0-12v 7) Dc : Variable Dc O/P 0-12v 8) GND : Ground terminal 9) DPM : 31/2 digit DC volt meter to measure DC voltage at different points 10) Vin : +ve I/P of error detector feedback voltage 11) V f : -ve I/P of error detector feedback voltage 12)V e : Error voltage 13) P : 10 turn potentio meter to vary potential gain from 0- 20 with indicating dial 14) I : 10 turn potentio meter to vary the integral gain from 10-1000 15) D : 10 turn potentio meter to vary the derivative gain from 1-0.01 16) Controller : PID controller with variable PID parameters. 17) ON/OFF : On/off switch for P,I,D individually 18) + : Adder 19) INV AMP : Units gain inverting amplifier to find the effect of Positive feed back
20) Process:
A) First order system : First order system with time constant of 3m sec. B) Second order system: Second order system with time constant of 5 sec. C) Time constant : 1m sec Suitable for square wave I/P D) Integrator : 2m sec. Time with 180 0 phase shift
A) Proportional controller open loop:
Procedure: www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 15 1) Make the connections as given in to the figure. 2) Connect DC voltage o f 0.5 volts to PID input. 3) Connect feed back to ground 4) Vary the proportional gain pot 5) Switch on P controller and keep I and D controller at off position 6) Vary the proportional gain pot and note down the O/P voltage
S.NO V in Gain (K c ) VOLT
b) Integral Controller-Open loop :
Procedure: 1. Make the connections as given in the circuit diagram. 2. Connections a small voltage of .2 volts to input. 3. Connect feed back to ground. 4. Switch off P and I. Switch on D controller. 5. d) Derivative controller open loop
Procedure: 1.Make the connections as per circuit diagram 2.Connect a small DC voltage of .2 volts to I/P 3.Connect feed back to ground 4.Switch off P and I . Switch on D controller
D) Proportional controller closed loop
Procedure: 1.Make the connections as shown in the figure. 2.Keep I and D controllers at off positions 3.Connect DC supply to v in
4.Connect first order plant in the loop. 5.Note down V m , V f, V error to direct P- gained and enter in the tabulars column. 6.Error voltage =V s /1+G
Table :
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 16 S.NO P-GAIN -C S Feedback voltage v s Error voltage -Ve Cal error
(e) Integral + Proportional + Derivate controller ( PID):
Procedure: 1. Make the connections as given in the circuit diagram 2. Connect square wave to v in
3. Connect the constant block only the loop 4. Connect X- input to triangle wave form and Y- input to feed back input -V f
Graph :
Result :
Questions :
1. Define proportional ? 2. Define integral controller ? 3. Why should we do not connect first order& second order in the loop of PID controller ? 4. Define second order system ? 5. Where shall we apply PID controller ? www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 17
TEMPERATURE CONTROLLER USING PID
CIRCUIT DIAGRAM:-
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 18
TEMPERATURE CONTROLLER USING PID
AIM: To study the on/off Temperature controller. APPARATUS:- 1) On/off temperature module. 2) Heater system. 3) PT-100 RTD Sensor. 4) Water Controller.
PROCEDURE:- 1) Connect the RTD sensors PT-100 to the binding post provided. Connect the heater table to the plug provided. 2) Keep the rotary switch in zero degree position. Set the meter reading it should be show zero degree. 3) Keep the rotary switch in RTD position; The meter reading indicates the temperature. 4) Set the temperature value to required temperature setting. 5) Keep the RTD in water container. 6) Note the temperature at which Heater turns off. 7) Repeat the steps 3 to 6 to various temperatures.
RESULT:
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 19 6. CHARACTERISTICS OF MAGNETIC AMPLIFIER Circuit Diagram:
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 20 6. CHARACTERISTICS OF MAGNETIC AMPLIFIER
AIM: To study the characteristics of magnetic amplifier. APPARATUS: magnetic amplifier kit, patch cords, load (100wbulb), external dc supply Ammeters (0-100mA, MC)-1 No Ammeter- (0-1A, MI)-1No Procedure for series connected magnetic amplifier parallel connected magnetic amplifier
1) Connections are made as per the CKT diagram 2) Switch on the main supply and give the DC power to the magnetic amplifier through RPS. 3) Now vary the DC power in steps and note down the readings of I C and I L
and Observe the load at variable DC voltage. 4) plot the graph between I C and I L at variable position for both series connection and parallel connection
Tabular form: Series Magnetic amplifier: 50V Voltage(v) I C (mA) I L (mA)
Parallel Magnetic Amplifier:
100V Voltage(v) I C (mA) I L (mA)
100V Voltage(v) I C (mA) I L (mA)
50V Voltage(v) I C (mA) I L (mA)
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 21 MODEL GRAHPH:
Result:
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 22
7. DC POSITOIN CONTROL SYSTEM
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 23 7. DC POSITOIN CONTROL SYSTEM
AIM: To study the position control system by using DC signals. APPARATUS: DC position control system units. OPERATION WITH OUT FEEDBACK (SW 1 In off position i.e., Tacho out) (1). Now slowly advance the input potentiometer P 1 in clockwise direction. The O/P potentiometer along with load will be seen to be following the change in the input potentiometer. (2). Keep the pot P 1 at around 180 degrees position. P 2 will be also in the same position. (3). Now change the input pot in a step fusion by a 60 to 80 degrees. The O/P will be observed to change in oscillatory mode before it settles in final position. The tendency for oscillations is found to be dependent on the amplifier gain setting. For high gain there are too many oscillations where as for low gain oscillations are reduced but with static error.
OPERATION WITH STABILIZING FEEDBACK: 1. Now put the SW1 in lower position. 2. SW2 must be in down position i.e., degeneration mode. Keep P 4 in fully anti clock wise direction. 3. Now take the pot P 1 to 180 0 position and effect step input change in one of the directions, O/P gain indicates oscillations is found to be dependent on the amplifier gain setting. For high gain there are too many oscillations where as for low gain oscillations are reduced but with static error.
OPERATION WITH STABILIZING FEEDBACK: 1. Now put the Sw1 in lower position. 2. Sw2 must be in down ward position i.e degeneration mode. Keep P4 in fully anti clock wise direction. 3. Now take the pot P1 to 180 0 position and effect step input change in one of the directions, O/P gain indicates oscillations. 4. Now advance the pot P 4 in clock wise direction, the O/P now is observed to follow the I/P in a smooth if P 4 pot io too much advance. The o/p in a sluggish fashion indicating over damped system. 5. Now put switch if P1 disturbed the pot P2 is found to oscillate continuously around the desired position.
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 24 Table: 1 DEGENERATIVE:
S.No I/P angular position degrees Output angular position degrees With stabilizing Remarks
Table: 2
REGENERATIVE:
Table: 3
Result:
S.No I/P angular position degrees Output angular position degrees With stabilizing Remarks
S.No I/P angular position degrees Output angular position degrees With out stabilizing Remarks
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 25 8.CHARACTERISTICS OF AC SERVO MOTOR
AIM: To study the characteristics of AC servo motor. Front panel details:
1. Power : main ON/OFF switch to the unit with built in indicator. 2. RPM : tachometer to display to RPM 3. Ammeter : Ammeter to measure the DC motor armature current 4. Servomotor ON/OFF : AC supply ON/OFF switch to the servo motor. 5. Load ON/OFF : ON/OFF switch to load the motor. 6. R : Potentio meter to vary the load 500 ohms/25watts. 7. V dc : 12V unregulated DC supply to DC motor 8. E b Terminals to measure the back EMF 9. Control winding: Control winding terminals of AC servo motor 10 Reference winding: Reference winding of AC servo motor. 11. Control voltage : Auto transformer to vary the AC supply to control winding.
TABLE TO PLOT SPEED Vs BACK EMF:
Sl no Speed rpm Backemf- volts
PROCEDURE:
1. Study all the controls on the front panel. 2. Initially keep load control switch at OFF position, indicating the armature circuit of dc machine is not connected to auxiliary dc supply 12V keep servo motor supply switch also at off position. 3. Ensure that load potentiometer and control voltage auto transformer at minimum position. 4. Now switch on mains supply to the unit and also AC servo motor supply switch vary the control voltage transformer. You can observe that the AC servo motor will stars rotating and the speed will be indicated by the tachometer in the front panel. 5. With load switch at OFF position switch ON AC servomotor and keep the speed in the minimum position. You can observe that the AC servomotor starts moving with speed being indicated by the tachometer and set the speed for maximum speed. Now switch on the load switch and start loading AC servo motor by varying the laod potentiometer slowly, Note down the corresponding values of Ia and speed and enter these readings in the table. And also note down the control panel.
S.No Ia(mA) N(rpm) P(watts) Torque(Gm-cm)
Repeat for Vc=3/4 th 230V www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 26
Draw the graph of torque Vs speed.
K2=DT/DN
Determine the motor constant K1: 1. Apply rated voltage 230V to control winding. 2. Apply load on the motor gradually till the motor wil run in the RPM. 3. Note down I and calculate torque 4. Decrease the load on the motor slightly the motor will run at certain rpm. 5. Reduce Vc slightly till the speed the motor comes to N rpm 6. repeat different loads. 7. Repeat for N2 rpm.
Draw the graph of Torque V/S V C
K1= DT/DVc
Ia measured by ammeter which is connected in series with the power supply & variable resistance (load control). This method does not take in to the account the no load torque developed by the ac servo motor. To measure torque developed at no load (i.e torque just required to rotate rotor of ac servomotor, rotor of dc motor) the ac servomotor is switched off. Now the dc machine run as the help of dc power supply, speed will be controlled by variable resistance again we have to effect the measurement of Ia for a given speed. From the product of Eb( back emf developed by the motor) and the armature current taken, we can find the mechanical power developed at the shaft. Again we must use the formula.
P= 2pi*NT/60 Torque = P*1.019*10 4 *60/2pi*N
For various speeds, we can note down the no load torque required to be developed by the motor. This torque is negligible & may not be taken in to account for normal testing. Torque calculation for a sample data:
Ia =0.17A Speed N= 850 rpm For speed 850rpm- Eb = 0.96V www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 27 Therefore power P = Eb*Ia = 0.96*0.17 = 0.1632 watts.
T= P*1.019 * 10 4 *60/2piN
T = 0.1632*1.019*10 4 * 60/2*3.142*850
T = 18.68 Gm-cm
GRAPHS: Respective graphs are drawn separately
RESULT: www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 28
9. TRANSFER FUNCTION OF DC GENERATOR
Circuit Diagram:-
Circuit diagrams to find R f and L f :
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 29 9. TRANSFER FUNCTION OF DC GENERATOR
AIM: To find out the transfer function of a DC generation, after determining the various Constants .APPARATUS:
S.NO NAME RANGE TYPE Qty 1 Motor generator set ______ ______ 1 2 Rheostat 290ohm/2.4A --------- 1 3 Ammeter (0-2.5)A MC 1 4 Voltmeter (0-250)V MC 1 5 Tachometer 0-5000 rpm Digital 1 6 Multimeter ------------- Digital 1.
PROCEDURE: 1.Make all the connections as per the circuit diagram 2. Keep the rheostat of motor with starter and adjust the speed to rated value. 3.Start the DC motor with starter and adjust the speed to rated value. 4.To determine the kg. the magnetization characteristics of separately excited DC generation is to be drawn. Use the straight line position of the curve to determine Kg= E G /I F . 5. Field resistance of generation R1 is determined by volumes and ammeter method.
Tabular form:
1) Magnetization characteristics:
S.No I f (A) Eg(V)
2) Field Resistance: S.No V I R f =V/I
3) Field Impedance:
S.No I(A) V(V) Z f (ohms)
Model Graph: www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 30
Model Calculations: X f = (Z f 2 R f 2 ) L f = X L /2f Transfer function, T(s) = Kg/1+sg Where Kg = Eg/If g = L f /R f
RESULT: www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 31 10. ROOT LOCUS PLOT, BODEPLOT FROM MATLAB
AIM: To plot root locus and bode plot by using MATLAB.
SIMULATION TOOLS:
1. IBM PC Compatible with MATLAB Software 2. MATLAB Simulator PROGRAMME:
a) /* root locus */ num = [1,3]; den = [1, 2, 3, 4]; rlocus (num, den)
Grid
b) / * Bode plot * /
num = [1, 3]; den = [1,2, 3, 4];
bode (num, den)
grid
RESULT:
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 32
11. CHRACTERISTICS OF DC SERVO MOTOR
BLOCK DIAGRAM:
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 33 11. CHRACTERISTICS OF DC SERVO MOTOR
AIM: To study the characteristics of DC servo motor i) Speed Vs Va ii) Speed Vs torque iii) Torque Vs Ia
APPARATUS: DC Servo motor controller Voltmeter - 0-30V
THEORY: The motors that are used in automatic control systems are called servomotrs. The servomotors are used to convert an electrical signal applied them into an angular displacement of shaft. Depending on the supply required to run the motor, they are broadly classified as DC servo motor and AC servomotors. But, the DC servomotrs are expensive than AC servomotors. But, the DC servo motors have linear characteristics and so it is easier to control DC motors are capable of delivering over 3 times their rated torque for a short time but AC motors will short at 2 to 2.5 times their rated torque. In DC servomotors mainly 2 types of motors are classified 1. Permanent magnetic motors and electromagnetic field motors.
The DC servo motors are generally used for large power applications such as in machine tools and robotics.
PROCEDURE:
1. Connections are made as per the circuit diagram the motor is operated on open loop. 2. Connect the motor to he o/p power amplifier in the servo controller through ammeter. Connect a Voltmeter across the motor armature. 3. Set the controller to the proportional by connecting the I controller i/p to ground. 4. Set the proportional gain to minimum. 5. Switch on the supply to motor controller and the pulse release. 6. Set Vref =1V, slowly increase the gain Kp voltage by means of proportional gain adjustment and find the voltage at which the motor just running. 7. vary reference voltage in speeds and for each step, note down the motor speed & Va. It gives T Vs Va characteristics. 8. Run the motor at 1500rpm by suitably adjusting the Vref & Kp note down Va, Ia & speed. 9. Apply load by moving brake magnet close to the disc.Apply load in steps of 0.1A. Note down Ia, Va& speed for each step. 10. Ammeter current reaches a value above which it may not increase when the speed is low, the eddy current induced in the disc becomes, lag which reduces the load torque. 11. Draw the graph between W Vs Va, T Vs Ia, W Vs Ia.
Tabular form: To plot w Vs Va and w Vs Eb.
S.No Vref Eb Va Ia N W=2N/60
Tabular form: to plot w Vs Ia and Vs Ia www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 34
To find Kf from the graph Eb Vs w:
Eb = Ea IaRa
Eb = Kb * w
Kf = Eb /w
MODEL GRAPHS:
RESULT: Hence the characteristics of DC servomotor are drawn.
S.No Va Ia N w = K f * Ia
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 35
12. TRANSFER FUNCTION OF D.C SHUNT MOTOR
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 36 12. TRANSFER FUNCTION OF D.C SHUNT MOTOR
AIM: To Determine the transfer function of DC motor by conducting Retardation test.
APPARATUS: S. No. Description Range Type Qty 1 Ammeter (0-2) A M.C 1 2 Voltmeter (0-5) A (0-300) V M.C
Specification Shunt motor Voltage 220v Current 19A Capacity 5 Hp Speed 1500rpm Excitation Current 1A Voltage 220v
THEORY: We perform armature control of d.c motor in the system shown Ra = resistance of armature () La = inductance of armature wdg(h) Ia = Armature current (A) Ea = applied armature voltage(V) Ed = back e.m.f (V) Tm = torque developed by motor (N-M) = angular displacement of motor shaft J = moment of intertia of motor and load ref motor shaft (kg-M 2 ) F = equivalent viscous friction co- efficient of motor end load ref to motor shaft (N-M / rad / sec) www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 37 In servo applications the D.C motors are generally used in linear range of magnetization curve. Therefore the air gap flux is prop to I F
= k f I f
The torque I m developed by motor is prop to the product of I a and air gap flux i.e T m = K i K f I f I a , K 1 is constant In the armature controlled D.C motor the field current is sept constant so that T m = K t i a ------------(1) Where K t is known as motor torque constant the motor back emf being prop to speed given as E d = K b d / dt -------------(2) Where K b is back emf constant . the deff eq n of armature ckt is L a dia / dt + R a I a + e b = v a ----------(3) The torque eq n is J d 2 / dt 2 + f d / dt
= T m = K t I a -------(4) Taking l.t to 1,2,3 and 4 E d (s) = sk b (s) --------(5) La s Ia(s) + Ra Ia(s) + Eb(s) = Va(s) ----------(6) Js 2 (s) + fs (s) = Tm(s) -------(7) Tm(s) = kf Ia(s) ------(8) From 7&8 eq n
Js 2 (s) + fs (s) = kf Ia(s) Ia(s) = (Js 2 + fs)/ Kt (s) ------(9) From 5,6,9 Va(s) = (La s + Ra) (Js 2 +fs)/kt (s) + sk b (s) = (Las + Ra) (J 2 s + fs) + sk b kt/ kt (s) (s)/Va(s) = kt / s[(Las + Ra) (Js+f) + k b k t ] The T.F is given as G(s) = kt / s [(L a s+Ra) (Js+f) + k b k t ] At constant speed k b = k t
PROCEDURE: 1. connect the circuit as per ckt diagram 2. check the rated speed of motor 3. start the motor with armature on no-load 4. Switch on the supply from armature motors and take the taken to reach different speed from rated speed. 5. load the armature of motor with resistance load 6. switch off the supply and take time taken for different times from rated speed 7. note down the values of voltmeter and ammeter 8. draw the graph b/w N&t and draw tangent from the rated speed on y- axis on to the curve which cuts the x- axis i.e total time taken to reach zero speed known as time constant 9. determine the different constants of the motor 10. determine the T.F of D.C motor i.e.G(s) = kt / s[k b k t + (LaRas)(t s +f)]
OBSERVATIONS:
With out load
With load
N T (Sec) N T(sec)
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 38
V
I
Eb
V
I
Ra
Model calculations:
W intial = 2 N/60 W final = 2 N 1 /60
dw/dt =( W intial - W final )/( T intial - T final )
K b = E b /(dw/dt) W 1 = V* I W= J* (2 N 1 /60) * dw /dt W+ W 1 = (J * (2 N 2 /60)* 2 (N initial - N 2 )/60) / (T intial - T final ) W 1
= (W+W 1 ) W 1 = VI from the graph find Time constant But = J/f and hence find friction coefficient f. Therefore transfer function,
T(s) = kt / s [(L a s+Ra) (Js+f) + k b k t ]
Circuit Diagram:-
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 39
RESULT:- www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 40 13. SIMULATION OF STATE SPACE MODELS USING MATLAB
AIM: To find the transfer function of the given system, controllability, Obeservability and System stability.
X= AX + BU Y= CX + DU -1 1 0
A= 0 -4 2
0 0 -10
1 B = 0 C = 1 0 1 D=(0)
1
SIMULATION TOOLS:
1. IBM PC Compatible with MATLAB Software 2. MATLAB SIMULATOR THEORY:
State: Minimum amount of information required to estimate the future of the system. State variable: The minimal set of these variables which describe the state of the system. Suppose n state variables are represented as n components of a state then the vector is known as state vector.
x 1 (t)
x 2 (t) X(t) = x n n X 1
State Space model representation
State eq n is X(t) = AX(t) + BU(t) o/p eq n Y(t) = Cx(t) + DU(t) www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 41
Transfer function matrix, T.F = C(SI A) -1 B+D. A system is said to be completely state controllable if it is possible to find an input u(t) that will transfer a system from any initial state to any final state over a specified time interval. Controllable matrix S= [ B AB A 2 B ..A n-1 B] If rank of the matrix n, then the system is state controllable. Rank (S) = n. [|B| 0] A system is said to be state observability the state of the system can be determined from the knowledge of input U(t) & o/p y(t) over a finite interval of time. The representation is W = [C T A T C T (A T ) 2 C T .(A T ) n-1 C T ] Rank (W) = n [observable]
Program-1 A= [-1 1 0 ; 0 -4 2 ; 0 0 -10]
B= [1 0 -1];
C= [1 0 1];
D= [0]
[num, den]=ss2tf [A, B, C, D];
disp(num);
disp(den);
Program-2 A= [-1 0 0, 0 -4 2, 0 0 -10];
B= [1 0 -1];
C= [1 0 1];
D= [0]
S=ctrb(A, B);
n=det(s);
if abs(n)<eps
disp(system is not controllable);
else
disp(system is controllable);
end
Program-3 A= [-1 0 0, 0 -4 2, 0 0 -10]; www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 42
B= [1 0 -1];
C= [1 0 1];
D= [0]
W=obsv(A,C);
n=det(W);
if abs(n)<eps
disp(system is not observabilety);
else
disp(system is observability);
end.
RESULT: Hence the transfer function of the given system, controllability, observability and system stability are found.
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 43
Add On Experiments:-
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 44
1.SIMULATON OF TRANSFER FUNCTION USING OPERATIONAL AMPLIFIER
Circuit Diagram:-
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 45
1. SIMULATON OF TRANSFER FUNCTION USING OPERATIONAL AMPLIFIER AIM:- To simulate transfer function using operational amplifier. APPARATUS:- Bread board, Resistors 1k and 100k, Capacitors-4.7uf, CRO, Function generator. THEORY:-The operational amplifier is a direct coupled high gain amplifier consisting of two or more differential amplifier followed by a level shifter and output stage. The feedback is added to control its overall response characteristics. It is used to perform a wide variety of linear and non-linear operations. ELECTRICAL PARAMTERS OF PO-OMP:- INPUT OFFSET VOLTAGE:- It is the voltage which must be supplied between the input terminal of an operational amplifier to balance it. OUTPUT OFFSET VOLTAGE: It is the difference between the dc voltages present at the two output terminals. COMMON MODE REJECTION RATIO (CMRR):- It is defined as the ratio of the differential voltage gain (Adm) and common mode voltage gain (Acm) CMRR=Adm/Acm. INPUT RESISTANCE:- It is the equivalent resistance that can be measured at either the inverting input terminal with the other terminal connected to ground. SLEW RATE:- It is the time rate of change of the closed loop amplifier output voltage under large signal conditions. S.R=dVo/dt\max. v/us POWER SUPPLY REJECTION RATIO:- It is the ratio of change in input offset voltage to the corresponding change in one power supply voltage, all remaining power supply voltages held constant. PROCEDURE:- 1. Connect as per circuit diagram of integrator. 2. Give a sequence input to integrator ckt via function generator. 3. Observe the output waveform on CRO for lower frequency output. 4. The frequency is adjusted to higher values to get a triangular output. 5. Note the time period and frequency of output waveform.
RESULT:-
www.jntuworld.com www.jntuworld.com www.jwjobs.net Control Systems and Simulation Lab Electrical & Electronics Engineering Department-BVRIT 46