Professional Documents
Culture Documents
DENISON HYDRAULICS
high performance hydraulic vane pumps
single, double, triple
T7 and T67 industrial application
Publ. 1 - AM0705 - A
09 / 2000 / 2000 / FB
Replaces : 1 - AM 079 - B
L14 - 10705 - 1
GENERAL
General characteristics.................................................................................................... 3
Minimum and maximum speeds .................................................................................... 4
Pressure ratings ............................................................................................................... 4
Minimum allowable inlet pressure ................................................................................. 5
Main calculation ............................................................................................................. 6
Intermittent pressure rating............................................................................................. 6
Description...................................................................................................................... 7
Application advantages................................................................................................... 7
Hydraulic fluids .............................................................................................................. 8
Shafts .............................................................................................................................. 9
Priming at starting........................................................................................................... 9
General characteristics.................................................................................................... 9
Formulas ....................................................................................................................... 10
Notes ............................................................................................................................. 11
T7B - T7BS
T7BB - T7BBS
T67CB
T67DB
T67EB
T67DBB
T67DCB
T67EDB
Dimensions .................................................................................................................. 27
Ordering code and operating characteristics ................................................................ 28
Technical data ............................................................................................................... 29
Porting diagrams for double and triple pumps ............................................................. 30
Porting diagrams for triple pumps................................................................................ 31
Addresses ...................................................................................................................... 32
Back to Content
2
CHARACTERISTICS
These T67 series vane pumps have been specially designed for high/low circuit. The
combination of different cartridges in double and triple pumps allows low flow at high
pressure (4350 PSI max.) and high flow at lower pressure. This is a clever way to
optimize your circuit design.
This pump feature will also allow a very fast pressure cycle change with a very precise
flow repeatability.
GREATER FLOW
B:
C:
D:
E:
HIGHER PRESSURE
B:
C:
D:
E:
BETTER EFFICIENCY
Over 94 % under high pressure, which increases productivity and reduces heating and
operation costs.
MOUNTING FLEXIBILITY
CARTRIDGE DESIGN
Viscosities from 3900 to 60 SUS permit colder starts and hotter running. The balanced
design compensates for wear and temperature changes. At high viscosity or cold
temperature, the rotor to side plates gap is well lubricated and improves mechanical
efficiency.
GENERAL APPLICATIONS
INSTRUCTIONS
1. Check speed range, pressure, temperature, fluid quality, viscosity and pump rotation.
2. Check inlet conditions of the pump, if it can accept application requirement.
3. Type of shaft : if would support operating torque.
4. Coupling must be chosen to minimize pump shaft load (weight, misalignment).
5. Filtration : must be adequate for lowest contamination level.
6. Environment of pump : to avoid noise reflection, pollution and shocks.
Back to Content
3
MINIMUM AND MAXIMUM SPEED, PRESSURE RATINGS - T7 AND T67 SERIES INDUSTRIAL APPLICATION
Theoretical
Displacement Minimum
Vi
Speed
Series Size Displ.
T7
T67
C
B02
B03
B04
B05
B06
B07
B08
B10
B12
B15
B02
B03
B04
B05
B06
B07
B08
B10
B12
B15
003
005
006
008
010
012
014
017
020
022
025
028
031
014
017
020
024
028
031
035
038
042
045
050
042
045
050
052
062
066
072
in3/rev.
.35
.60
.78
.97
1.21
1.37
1.52
1.94
2.50
3.05
.35
.60
.78
.97
1.21
1.37
1.52
1.94
2.50
3.05
.66
1.05
1.30
1.61
2.08
2.26
2.81
3.56
3.89
4.29
4.84
5.42
6.10
2.90
3.55
4.00
4.80
5.50
6.00
6.80
7.30
8.30
8.90
9.64
8.07
8.70
9.67
10.00
12.00
13.00
13.86
Maximum Speed
HF-0,HF-1 HF-3, HF-4
HF-2
HF-5
RPM
RPM
RPM
HF-0, HF-2
Int. Cont.
PSI
PSI
600
3600
1800
4650
4200
4350
4060
4000
3500
4350*
4000
4060
3500
4000
3500
3000
2300
3500
3000
3000
2300
3500
3000
3000
600
3600
1800
Maximum Pressure
HF-1, HF-4, HF-5
Int.
Cont.
PSI
PSI
HF-3
Int. Cont.
PSI
PSI
3500
3000
2500
2000
3500
3000
2500
2000
3000
2500
2500
2000
2500
2000
2500
2000
3000
600
2800
1800
2500
600
2500
1800
2300
3000
2500
2200
600
2200
1800
2300
3000
2500
HF-0, HF-2 = Antiwear petroleum base. HF-1 = Non antiwear petroleum base. HF-5 = Synthetic fluids.
HF-3 = Water in oil emulsions. HF-4 = Water glycols.
* Please consult DENISON Hydraulics for applications over 4350 PSI.
For further information or if the performance characteristics outlined above do not meet your own particular requirements, please consult your local
DENISON Hydraulics office.
Back to Content
4
MINIMUM ALLOWABLE INLET PRESSURE (PSI ABSOLUTE) - T7 AND T67 SERIES INDUSTRIAL APPLICATION
Cartridges
Size Displ.
B02
B03
B04
B05
B06
B
B07
B08
B10
B12
B15
003
005
006
008
010
C
012
014
017
020
022
025
028
031
014
017
020
024
028
D
031
035
038
042
045
050
042
045
050
E
052
062
066
072
1200
11.6
1500
11.6
1800
11.6
2100
11.6
Speed RPM
2200
2300
11.6
11.6
2500
11.6
12.2
11.6
2800
11.6
14.3
13.0
11.6
14.5
11.6
11.6
11.6
11.6
12.3
12.3
13.3
13.8
14.9
14.2
15.2
15.7
16.1
14.5
15.2
13.0
12.3
13.0
12.3
11.6
11.6
11.6
11.9
12.3
13.0
13.3
13.8
13.0
13.8
14.2
13.0
13.8
14.2
14.5
12.8
13.8
14.5
12.3
14.2
14.8
13.3
13.8
14.2
14.5
14.8
15.2
15.8
14.5
11.6
11.6
11.6
11.6
13.0
12.3
12.3
12.3
13.8
12.3
13.8
14.5
14.8
15.2
15.7
15.8
15.2
16.0
17.1
17.8
18.7
3000
3600
11.6
11.6
11.9
14.2
12.3
13.0
15.2
15.2
16.4
Displ.
B02
B03
B04
B05
B06
B07
B08
B10
B12
B15
003
005
006
008
010
012
014
017
020
022
025
028
031
014
017
020
025
028
031
035
038
042
045
050
042
045
050
052
062
066
072
Inlet pressure is measured at inlet flange with petroleum base fluids at a viscosity between 60 and 300 SUS. The difference between
inlet pressure at the pump flange and atmospheric pressure must not exceed 2.9 PSI to prevent aeration.
Multiply absolute pressure by 1,25 for HF-3, HF-4 fluids.
by 1,35 for HF-5 fluid.
by 1,10 for ester or rapeseed base.
Use the cartridge with the highest absolute pressure for double and triple pumps.
Back to Content
5
MAIN CALCULATION
To resolve
Volumetric displ.
Available flow
Input power
Vi [in3/rev.]
qv [GPM]
P [HP]
Routine :
1. First calculation Vi =
Performances required
Requested flow qv [GPM] 19.8
Speed
n [RPM] 2500
Pressure
p [PSI] 3600
Example :
231 Q
n
Vi =
231 x 19.8
= 1.83 in3/rev.
2500
qVI =
1.94 x 2500
= 21.0 GPM
231
Pi =
21.0 x 3600
= 44.1 HP
1714
9. Results
Vi = 1.94 in3/rev.
qVe = 20.21 GPM
P = 45.30 HP
T7B B10
INTERMITTENT PRESSURE
RATING
T7 and T67 units may be operated intermittently at pressures higher than the
recommended continuous rating when the time weighted average of pressure is less
than or equal to the continuous duty pressure rating. This intermittent pressure rating
calculation is only valid if other parameters : speed, fluid, viscosity and contamination
level are respected.
For total cycle time longer than 15 minutes, please consult your DENISON Hydraulics
representative.
Example : T7B - B10
Duty cycle
4 min. at 4650 PSI
1 min. at 500 PSI
5 min. at 2300 PSI
(4 x 4650) + (1 x 500) + (5 x 2300)
= 3070 PSI
10
3070 PSI is lower than 4200 PSI allowed as continuous pressure for T7B - B10 with
HF-0 fluid.
Back to Content
6
Inlet
Outlet
Inlet
90 Section
Suction ramp
where unloaded
vane moves out.
Section B-B
Pin cavity is at a steady
pressure equal to that at
discharge port.
Section A-A
Discharge ramp
where unloaded
vane moves in.
Nota : The "E" and "B" size cartridges are with 12 vanes.
APPLICATION ADVANTAGES
The high pressure capability up to 4650 PSI, in the small envelope, reduces
installation costs and provides extended life at reduced pressure.
The high volumetric efficiency, typically better than 94%, reduces heat generation,
and allows speeds down to 600 RPM at full pressure.
The high mechanical efficiency, typically better than 94%, reduces energy
consumption.
The wide speed range (600 RPM at 3600 RPM), combined with large size cartridge
displacements will optimize operation for the lowest noise level in the smallest
envelope.
The low speed (600 RPM), low pressure, high viscosity (3900 SUS) allows
applications in cold environment with a minimum energy consumption and without
risk of seizure.
The low ripple pressure ( 29 PSI) reduces piping noise and increases lifetime of
other components in the circuit.
The high resistance to particle contamination, because of the double lip vane,
increases pump life.
The large variety of options (cam displacement, shaft, porting) allows customized
installation.
Back to Content
7
RECOMMENDED FLUIDS
ACCEPTABLE ALTERNATE
FLUIDS
The use of fluids other than petroleum based antiwear R & O fluids requires that the
maximum ratings of the pumps will be reduced. In some cases, the minimum
replenishment pressures must be increased. Consult specific sections for more details
(page 4).
VISCOSITY
VISCOSITY INDEX
+ 212
+ 122
+ 158
+ 149
The fluid must be clean before and during operation to maintain contamination level of
NAS 1638 class 8 (or ISO 18/14) or better. Filters with 25 micron (or better, 10 100)
nominal ratings may be adequate but do not guarantee the required cleanliness levels.
Suction strainers must be of adequate size to provide minimum inlet pressure specified.
100 mesh (149 micron) is the finest mesh recommended. Use oversize strainers or omit
them altogether on applications which require cold starts or use fire resistant fluids.
OPERATING TEMPERATURES
AND VISCOSITIES
Operating temperatures are a function of the fluid viscosities, fluid type, and pump.
Fluid viscosity should be selected to provide optimum viscosity at normal operating
temperatures. For cold starts, the pumps should be operated at low speed and pressure
until fluid warms up to an acceptable viscosity for full power operation.
WATER CONTAMINATION IN
THE FLUID
Back to Content
8
SPLINED SHAFTS
COUPLING SPLINES
The mating female spline should be free to float and find its own center. If both
members are rigidly supported, they must be aligned within .006 TIR or less to reduce
fretting. The angular alignment of two spline axes must be less than .002 per 1"
radius.
The coupling spline must be lubricated with a lithium molydisulfide grease or a
similar lubricant.
The coupling must be hardened to a hardness between 27 and 45 R.C.
The female spline must be made to conform to the Class 1 fit as described in
SAE-J498b (1971). This is described as a Flat Root Side Fit.
KEYED SHAFT
DENISON Hydraulics supplies the T7 and T67 series keyed shaft pumps with high
strength heat-treated keys. Therefore, when installing or replacing these pumps, the
heat-treated keys must be used in order to ensure maximum life in the application. If
the key is replaced, it must be a heat-treated key between 27 and 34 R.C. hardness. The
corners of the keys must be chamfered .030" to .040" at 45 to clear radii in the key
way.
NOTE
Alignment of keyed shafts must be within tolerances given for splined shafts.
SHAFT LOADS
These products are designed primarily for coaxial drives which do not impose axial or
side loading on the shaft. Consult specific sections for more details.
PRIMING AT STARTING
When the pump is set into operation for the first time, it must be primed at the lowest
possible speed and pressure. When a pressure relief valve is used at the outlet, it should
be backed off to minimize return pressure.
When possible, an air bleed off should be provided in the circuit to facilitate purging of
system air.
Never operate the pump at maximum speed and pressure without making sure that the
pump priming is completed and that the fluid is disaerated.
Mounting
standard
Weight without
connector and
bracket - Lbs
Moment of
inertia
lb.in2
ISO
3019-2 100 A2HW
SAE J744c
ISO/3019-1 SAE B
ISO
3019-2 100 A2HW
50.7
1.1
Suction
1"1/2
50.7
1.1
1" 1/2
71.8
4.0
2" 1/2
71.8
4.0
57.3
T67DBB
T67DCB
SAE J744c
ISO/3019-1 SAE B
SAE J744c
ISO/3019-1 SAE B
SAE J744c
ISO/3019-1 SAE C
SAE J744c
ISO/3019-1 SAE C
SAE J744c
ISO/3019-1 SAE C
T67EDB
ISO/3019-2
T7B
T7BS
T7BB
T7BBS
T67CB
T67DB
T67EB
SAE 4 bolts
J518c - ISO/DIS 6162-1
Pressure
1" or 3/4"
1" or 3/4"
2" 1/2
P1
1" or 3/4"
1" or 3/4"
P2
3/4"
3/4"
3.9
2" 1/2
1"
3/4"
80.7
9.1
3"
1" 1/4
3/4"
121.0
23.8
3" 1/2
1" 1/2
3/4"
134.5
11.5
4"
220.4
26.1
4"
P1
1"1/4
1"1/2
P2
1"
1"1/4
P3
3/4"
3/4"
Back to Content
9
lbs. in.
HP
U.S. gpm
rpm
displacement(in3 rev.)
Fluid motor torque
lbs. in.
HP
Back to Content
10
Back to Content
11
Model No
Cam ring
(Delivery at 0 PSI & 1200 RPM)
B02 = 1.84 GPM B07 = 7.13 GPM
B03 = 3.11 GPM B08 = 7.89 GPM
B04 = 4.06 GPM B10 = 10.08 GPM
B05 = 5.04 GPM B12 = 13.00 GPM
B06 = 6.28 GPM B15 = 15.85 GPM
UNC thread
T7BS
M0
M1
00
01
1"
3/4"
1"
3/4"
1"1/2
1"1/2
1"1/2
1"1/2
Seal class
1 = S1 (for mineral oil)
4 = S4 (for fire resistant fluids)
5 = S5 (for mineral oil and fire resistant
fluids)
Design letter
Porting combination
00 = standard
P = Pressure port
S = Suction port
Pressure p [PSI]
Do not operate the pump more than 5 seconds at any speed or
viscosity if internal leakage is higher than 50% of theoretical
flow.
Pressure p [PSI]
Load F [Lbs]
Pressure p [PSI]
Speed n [RPM]
Maximum permissible axial load Fa = 180 Lbs
Back to Content
12
DIMENSIONS & OPERATING CHARACTERISTICS - Weight : 50.7 Lbs - T7B AND T7BS SERIES
Model
T7B
T7BS
Code
M0
M1
00
01
A
M10
.75 deep
B
M12
.88 deep
3/8-16 UNC
.75 deep
1/2-13 UNC
.88 deep
C
1.03
.87
1.03
.87
D
2.06
1.87
2.06
1.87
E
1.00
.75
1.00
.75
F
5.50
5.50
5.75
5.75
G
2.75
2.75
2.87
2.87
H
.55
.55
.56
.56
Volumetric
Speed
displacement Vi n [RPM]
Flow qv [GPM]
Input power P [HP]
p = 0 PSI
p = 2000 PSI p = 4650 PSI p = 100 PSI p = 2000 PSI p = 4650 PSI
B02
.35 in3/rev
1200
1.84
1.41
0.27
2.54
1800
2.76
2.33
1.73
0.74
4.02
8.59
B03
.60 in3/rev
1200
3.11
2.68
2.08
0.34
4.02
9.06
1800
4.66
4.23
3.63
0.85
6.24
13.75
B04
.78 in3/rev
1200
4.06
3.63
3.03
0.40
5.13
11.64
1800
6.09
5.66
5.06
0.94
7.90
17.62
B05
.97 in3/rev
1200
5.04
4.61
4.01
0.45
6.27
14.31
1800
7.56
7.13
6.53
1.02
9.62
21.62
B06
1.21 in3/rev
1200
6.28
5.85
5.25
0.53
7.71
17.66
1800
9.42
8.99
8.39
1.13
11.79
26.66
B07
1.37 in3/rev
1200
7.13
6.70
6.10
0.58
8.71
19.98
1800
10.70
10.27
9.67
1.20
13.29
30.14
B08
1.52 in3/rev
1200
7.89
7.46
6.86
0.62
9.60
22.05
1800
11.84
11.41
10.81
1.27
14.62
33.24
B10
1.94 in3/rev
1200
10.08
9.65
9.05
0.75
12.15
27.98
1800
15.12
14.69
14.09
1.46
18.45
42.14
B12
2.50 in3/rev
1200
13.00
12.57
12.031)
0.92
15.56
33.591)
1800
19.50
19.07
1.72
23.55
18.541)
50.581)
3
2)
B15
3.05 in /rev
1200
15.85
15.42
14.95
1.08
18.89
38.112)
1800
23.78
23.35
1.97
28.55
22.882)
57.352)
- We do not recommand to use the B02 cartridge at 4650 PSI & 1800 RPM as the internal leakage is over 50% of theoretical flow.
1)
2
B12 = 4350 PSI max. int.
) B15 = 4060 PSI max. int.
Back to Content
13
Model No.
Modifications
P1
P2
P1
P2
S
Metric thread
T7BB - T7BBS
M0
M1
1"
3/4"
3/4"
3/4"
2"1/2
2"1/2
UNC thread
T7BBS
00
01
1"
3/4"
3/4"
3/4"
2"1/2 2"1/2
Seal class
1 = S1 (for mineral oil)
4 = S4 (for fire resistant fluids)
5 = S5 (for mineral oil and fire
resistant fluids)
Design letter
Porting combination (see page 30)
00 = standard
Direction of rotation (view on shaft end)
R = clockwise
L = counter-clockwise
Pressure p [PSI]
Double pump noise level is given with each section discharging at
the pressure noted on the curve.
Load F [Lbs]
Pressure p [PSI]
Do not operate the pump more than 5 seconds at any speed or
viscosity if internal leakage is higher than 50% of theoretical
flow.
Total leakage is the sum of each section loss at its operating
conditions.
HYDROMECHANICAL POWER LOSS (TYPICAL)
Pressure p [PSI]
Total hydromechanical power loss is the sum of each section at
its operating conditions.
Speed n [RPM]
Maximum permissible axial load Fa = 180 Lbs
Back to Content
14
DIMENSIONS & OPERATING CHARACTERISTICS - Weight : 71.9 Lbs - T7BB AND T7BBS SERIES
Model
T7BB
T7BBS
Code
M0
M1
00
01
A
M10
.75 deep
B
M12
.88 deep
3/8-16 UNC
.75 deep
1/2-13 UNC
.88 deep
C
1.03
.87
1.03
.87
D
2.06
1.87
2.06
1.87
E
1.00
.75
1.00
.75
F
5.50
5.50
5.75
5.75
G
2.75
2.75
2.87
2.87
H
.55
.55
.56
.56
Series
Volumetric
displacem. Vi
Pump
T7BB
Shaft
1
V x p max.
12666
Back to Content
15
Model No.
Modifications
P1
P2
Seal class
1 = S1 (for mineral oil)
4 = S4 (for fire resistant fluids)
5 = S5 (for mineral oil and fire
resistant fluid)
Design letter
Pressure p [PSI]
Double pump noise level is given with each section discharging at
the pressure noted on the curve.
Load F [Lbs]
Pressure p [PSI]
Do not operate the pump more than 5 seconds at any speed or
viscosity if internal leakage is higher than 50% of theoretical
flow.
Total leakage is the sum of each section loss at its operating
conditions.
HYDROMECHANICAL POWER LOSS (TYPICAL)
Pressure p [PSI]
Total hydromechanical power loss is the sum of each section at
its operating conditions.
Speed n [RPM]
Maximum permissible axial load Fa = 180 Lbs
Back to Content
16
Series
Shaft
1
2
5
V x p max.
12666
18972
18246
Volumetric
displacem. Vi
Back to Content
17
Model No.
P1
P2
Seal class
1 = S1 (for mineral oil)
4 = S4 (for fire resistant fluids)
5 = S5 (for mineral oil and fire resistant
fluids)
Design letter
Pressure p [PSI]
Pressure p [PSI]
Do not operate the pump more than 5 seconds at any speed or
Double pump noise level is given with each section discharging at
viscosity if internal leakage is higher than 50% of theoretical flow. the pressure noted on the curve.
Total leakage is the sum of each section loss at its operating
conditions.
PERMISSIBLE RADIAL LOAD
Load F [Lbs]
Pressure p [PSI]
Total hydromechanical power loss is the sum of each section at
its operating conditions.
Speed n [RPM]
Maximum permissible axial load Fa = 270 Lbs
Back to Content
18
P1
Series
Volumetric
displacem. Vi
014
017
020
024
028
031
035
038
0421)
0451)
0501)
2.90 in3/rev
3.55 in3/rev
4.03 in3/rev
4.85 in3/rev
5.47 in3/rev
6.00 in3/rev
6.77 in3/rev
7.34 in3/rev
8.30 in3/rev
8.89 in3/rev
9.64 in3/rev
B02
.35 in3/rev
B03
.60 in3/rev
B04
.78 in3/rev
B05
.97 in3/rev
B06
1.21 in3/rev
P2
B07
1.37 in3/rev
B08
1.52 in3/rev
B10
1.94 in3/rev
B12
2.50 in3/rev
B15
3.05 in3/rev
1) 042 - 045 - 050 = 2200 RPM max.
Shaft
1
2
V x p max.
38299
30638
Back to Content
19
Model No.
Modifications
P1
P2
Seal class
1 = S1 (for mineral oil)
4 = S4 (for fire resistant fluids)
5 = S5 (for mineral oil and fire resistant
fluids)
Design letter
Porting combination (see page 30)
00 = standard
Type of shaft
1 = keyed (SAE CC)
2 = keyed (non SAE)
3 = splined (SAE C)
4 = splined (SAE CC)
Pressure p [PSI]
Pressure p [PSI]
Do not operate the pump more than 5 seconds at any speed or
Double pump noise level is given with each section discharging at
viscosity if internal leakage is higher than 50% of theoretical flow. the pressure noted on the curve.
Total leakage is the sum of each section loss at its operating
conditions.
PERMISSIBLE RADIAL LOAD
Load F [Lbs]
Pressure p [PSI]
Total hydromechanical power loss is the sum of each section at
its operating conditions.
Speed n [RPM]
Maximum permissible axial load Fa = 449 Lbs
Back to Content
20
Shaft
2
3
V x p max.
30638
54207
Back to Content
21
Model No.
P1
P2
P3
Modifications
Mounting w/connection variables
01 = 4 bolts SAE flanges
(J518c) UNC thread
M1 = 4 bolts SAE flanges
(J518c) Metric thread
Seal class
1 = S1 (for mineral oil)
4 = S4 (for fire resistant fluids)
5 = S5 (for mineral oil and fire resistant
fluids)
Design letter
Porting combination (see pages 30 & 31)
00 = standard
P1
Series
Volumetric
displacem. Vi
014
017
020
024
028
031
035
038
0421)
0451)
0501)
2.90 in3/rev
3.55 in3/rev
4.03 in3/rev
4.85 in3/rev
5.47 in3/rev
6.00 in3/rev
6.77 in3/rev
7.34 in3/rev
8.30 in3/rev
8.89 in3/rev
9.64 in3/rev
B02
.35 in3/rev
B03
.60 in3/rev
B04
.78 in3/rev
B05
.97 in3/rev
B06
1.21 in3/rev
P2
&
B07
1.37 in3/rev
P3
B08
1.52 in3/rev
B10
1.94 in3/rev
B12
2.50 in3/rev
B15
3.05 in3/rev
1) 042 - 045 - 050 = 2200 RPM max. 2)
Back to Content
22
Pressure p [PSI]
Pressure p [PSI]
Load F [Lbs]
Pressure p [PSI]
Speed n [RPM]
Back to Content
23
Model No.
P1
P2
P3
Series
Modifications
Mounting w/connection variables
01 = 4 bolts SAE flanges
(J518c) UNC thread
M1 = 4 bolts SAE flanges
(J518c) Metric thread
Seal class
1 = S1 (for mineral oil)
4 = S4 (for fire resistant fluids)
5 = S5 (for mineral oil and fire resistant
fluids)
Design letter
Porting combination (see pages 30 & 31)
00 = standard
Direction of rotation (view on shaft end)
R = clockwise
L = counter-clockwise
Type of shaft
1 = keyed (non SAE) 3 = splined (SAE C)
2 = keyed (SAE CC) 4 = splined (SAE
Volumetric
displacem. Vi
Back to Content
24
Pressure p [PSI]
Pressure p [PSI]
Load F [Lbs]
Pressure p [PSI]
Speed n [RPM]
Back to Content
25
26
DIMENSIONS - Weight : 134.5 Lbs - T67DBB / T67DCB SERIES
Back to Content
Shaft
Vi x p max. P1 + P2 + P3
Shaft
Vi x p max. P1 + P2 + P3
T67DBB
38299
54207
T67DCB
58901
58901
27
Back to Content
Model No.
P1
P2
P3
Modifications
Mounting w/connection variables
4 bolts SAE flanges
(J518c) Metric thread
1 = P3 = 3/4" SAE
Mounting (pump)
P = 4 holes for pedestal mounting
F = Standard mounting
Seal class
1 = S1 (for mineral oil)
4 = S4 (for fire resistant fluids)
5 = S5 (for mineral oil and fire resistant
fluids)
Design letter
Porting combination (see pages 30 & 31)
00 = standard
Direction of rotation (view on shaft end)
R = clockwise
L = counter-clockwise
Type of shaft
1 = keyed (G45N - ISO 3019-2)
Back to Content
28
Pressure p [PSI]
Pressure p [PSI]
Load F [Lbs]
Pressure p [PSI]
Speed n [RPM]
Back to Content
29
Back to Content
30
Back to Content
31