You are on page 1of 8

http://projects.icbse.com/http://projects.icbse.

com/
Chemistry, C++, Physics, Maths, Biology, Social Science
Home
Biology
C++
Chemistry
IP
Maths
Physics
Social Science
javascript:void(0);
Top of Form 1
Bottom of Form 1
HYPERLINK "http://projects.icbse.com/"Home > Chemistry > Chemistry Project on Foaming
Capacity of Soaps
Chemistry Project on Foaming Capacity of
Soaps
D o w n l o a d P r o j e c t
http://projects.icbse.com/chemistry/297.pdfhttp://projects.icbse.com/chemistry/297.pdf
S h a r e

Foaming Capacity Of Soaps
Lourdes Central School,
Bejai, Mangalore
Investigatory Project
On
Foaming Capacity
Of Soaps
Kenneth Lobo
Class XI I
Contents
Acknowledgements 3
Preface 4
Introduction 5
Commercial preparation 6
Introduction to experiment 9
Objective and theory 10
Procedure 11
Observation table 12
Result 13
Test for hardness 14
Bibliography 15
Acknowledgement
I will treasure the knowledge imparted to me by
Mrs. Anita Thomas, my grateful thanks to her for the able teaching and guidance. I thank Mr.
Harsha Kumar, the Lab assistant for his cooperation.
I also thank my parents and my friends for their constant support and cooperation.
Preface
Soaps and detergents remove dirt and grease from skin and clothes. But all soaps are not equally
effective in their cleaning action. Soaps are the Na and K salts of higher fatty acids such as
Palmitic acid, Stearic acid and Oleic acid.
The cleansing action of soaps depends on the solubility of the long alkyl chain in grease and that
of the -COONa or the -COOK part in water.
Whenever soap is applied on a dirty wet cloth, the non polar alkyl group dissolves in grease
while the polar -COONa part dissolves in water. In this manner, an emulsion is formed between
grease and water which appears as foam.
The washing ability of soap depends on foaming capacity, as well as the water used in cleaning.
The salts of Ca and Mg disrupt the formation of micelle formation. The presence of such salts
makes the water hard and the water is called hard water. These salts thus make the soap
inefficient in its cleaning action.
Sodium Carbonate when added to hard water reacts with Ca and Mg and precipitates them out.
Therefore sodium carbonate is used in the treatment of hard water.
This project aims at finding the foaming capacity of various soaps and the action of Ca and Mg
salts on their foaming capacity.
Introduction
Soap is an anionic surfactant used in conjunction with water for washing and cleaning, which
historically comes either in solid bars or in the form of a viscous liquid. Soap consists of sodium
or potassium salts of fatty acids and is obtained by reacting common oils or fats with a strong
alkaline in a process known as saponification. The fats are hydrolyzed by the base, yielding
alkali salts of fatty acids (crude soap) and glycerol.
The general formula of soap is
Fatty end water soluble end
CH
3
-(CH
2
)
n
COONa
Soaps are useful for cleaning because soap molecules have both a hydrophilic end, which
dissolves in water, as well as a hydrophobic end, which is able to dissolve non polar grease
molecules. Applied to a soiled surface, soapy water effectively holds particles in colloidal
suspension so it can be rinsed off with clean water. The hydrophobic portion (made up of a long
hydrocarbon chain) dissolves dirt and oils, while the ionic end dissolves in water. The resultant
forms a round structure called micelle. Therefore, it allows water to remove normally-insoluble
matter by emulsification.
Commercial production of soap
The most popular soap making process today is the cold process method, where fats such as
olive oil react with strong alkaline solution, while some soapers use the historical hot process.
Handmade soap differs from industrial soap in that, usually, an excess of fat is sometimes used to
consume the alkali (super fatting), and in that the glycerin is not removed, leaving a naturally
moisturizing soap and not pure detergent. Often, emollients such as jojoba oil or Shea butter are
added at trace (the point at which the saponification process is sufficiently advanced that the
soap has begun to thicken), after most of the oils have saponified, so that they remain unreacted
in the finished soap.
Fat in soap
Soap is derived from either vegetable or animal fats. Sodium Tallowate, a common ingredient in
much soap, is derived from rendered beef fat. Soap can also be made of vegetable oils, such as
palm oil, and the product is typically softer.
An array of saponifiable oils and fats are used in the process such as olive, coconut, palm, cocoa
butter to provide different qualities. For example, olive oil provides mildness in soap; coconut oil
provides lots of lather; while coconut and palm oils provide hardness. Sometimes castor oil can
also be used as an ebullient.
Smaller amounts of unsaponifable oils and fats that do not yield soap are sometimes added for
further benefits.
Preparation of soap
In cold-process and hot-process soap making, heat may be required for saponification.
Cold-process soap making takes place at a sufficient temperature to ensure the liquification of
the fat being used.
Unlike cold-processed soap, hot-processed soap can be used right away because the alkali and fat
saponify more quickly at the higher temperatures used in hot-process soap making. Hot-process
soap making was used when the purity of alkali was unreliable.
Cold-process soap making requires exact measurements of alkali and fat amounts and computing
their ratio, using saponification charts to ensure that the finished product is mild and skin-
friendly.
Hot process
In the hot-process method, alkali and fat are boiled together at 80100 C until saponification
occurs, which the soap maker can determine by taste or by eye.
After saponification has occurred, the soap is sometimes precipitated from the solution by adding
salt, and the excess liquid drained off. The hot, soft soap is then spooned into a mold.
Cold process
A cold-process soap maker first looks up the saponification value of the fats being used on a
saponification chart, which is then used to calculate the appropriate amount of alkali. Excess
unreacted alkali in the soap will result in a very high pH and can burn or irritate skin. Not enough
alkali and the soap are greasy.
The alkali is dissolved in water. Then oils are heated, or melted if they are solid at room
temperature. Once both substances have cooled to approximately 100-110F (37-43C), and are
no more than 10F (~5.5C) apart, they may be combined. This alkali-fat mixture is stirred until
trace. There are varying levels of trace. After much stirring, the mixture turns to the
consistency of a thin pudding. Trace corresponds roughly to viscosity. Essential and fragrance
oils are added at light trace.
Introduction to the experiment
Soap samples of various brands are taken and their foaming capacity is noticed.
Various soap samples are taken separately and their foaming capacity is observed. The soap with
the maximum foaming capacity is thus, said to be having the best cleaning capacity.
The test requires to be done with distilled water as well as with tap water. The test of soap on
distilled water gives the actual strength of the soaps cleaning capacity. The second test with tap
water tests the effect of Ca
2+
and Mg
2+
salts on their foaming capacities.
Objective: To compare the foaming capacity of various soaps.
Theory: The foaming capacity of soap depends upon the nature of the soap and its
concentration. This may be compared by shaking equal volumes of solutions of different samples
having the same concentration with same force for the same amount of time. The solutions are
then allowed to stand when the foam produced during shaking disappears gradually. The time
taken for the foam to disappear in each sample is determined. The longer the time taken for the
disappearance of the foam for the given sample of soap, greater is its foaming capacity or
cleansing action.
Requirements: Five 100ml conical flasks, five test tubes, 100ml measuring cylinder, test tube
stand, weighing machine, stop watch.
Chemical Requirements: Five different soap samples, distilled water, tap water.
Procedure:
1. Take five 100ml conical flasks and number them 1, 2,3,4,5. Put 16ml of water in each flask
and add 8 Gms of soap.
2. Warm the contents to get a solution.
3. Take five test tubes; add 1ml of soap solution to 3ml of water.
Repeat the process for each soap solution in different test tubes.
4. Close the mouth of the test tube and shake vigorously for a minute. Do the same for all test
tubes and with equal force.
5. Start the timer immediately and notice the rate of disappearance of 2mm of froth.
Observations: The following outcomes were noticed at the end of the experiment
Test Tube no Vol. of soap solution Vol. of water added Time taken for disappearance
of 2mm
1. Dove 8ml 16ml 1142
2. Lux 8ml 16ml 328
3. Tetmosol 8ml 16ml 510
4. Santoor 8ml 16ml 1532
5. Cinthol 8ml 16ml 940
Result
The cleansing capacity of the soaps taken is in the order:
Santoor > Dove > Cinthol > Tetmosol > Lux
From this experiment, we can infer that Santoor has the highest foaming capacity, in other
words, highest cleaning capacity.
Lux, on the other hand is found to have taken the least amount of time for the disappearance of
foam produced and thus is said to be having the least foaming capacity and cleansing capacity.
Test for hardness in water
Test for Ca
2+
and Mg
2+
salts in the water supplied
Test for Ca
2+
in water
H
2
O +NH
4
Cl + NH
4
OH + (NH
4
)
2
CO
3

No precipitate
Test for Mg
2+
in water
H
2
O +NH
4
Cl + NH
4
OH + (NH
4
)
3
PO
4

No precipitate
The tests show negative results for the presence of the salts causing hardness in water. The water
used does not contain salts of Ca
2+
and Mg
2+
. The tap water provided is soft and thus, the
experimental results and values hold good for distilled water and tap water.
BIBLIOGRAPHY
Parts of this project have been referred from foreign sources and have been included in this
investigatory project after editing.
The references of the sources are as follows:
Books:
Together With Lab Manual Chemistry-XII
Comprehensive Chemistry 12
Internet sources:
www.wikipedia.org
www.google.com
www.yahoo.com
Structure of soap molecule and micelle formation
Related:
C++ Project on Telephone Directory System
TELEPHONE DIRECTORY SYSTEM // TELEPHONE DIRECTORY SYSTEM
#include #include #in...
Chemistry Project on Optical Fiber and its Applications
Optical Fiber and its Applications Name: ...
Chemistry Project To Study the Setting of Cement
Setting of Cement AIM To Study the Setting of Cement CERTIFICATE This is to certify
that thi...
C++ Project on Periodic Table
Periodic Table /* Program Title : Periodic Table There is some personal infomation in ...
Comments (1) Trackbacks (0) Leave a comment Trackback
1.
2. indu c
3. October 11th, 2010 at 05:10 | #1
4. Reply | Quote
5. thank you very much.
6. No trackbacks yet.
Name (required)
E-Mail (will not be published) (required)
Website
Subscribe to comments feed
Notify me of follow-up comments by email.
Notify me of new posts by email.
Bottom of Form 2
HYPERLINK "http://projects.icbse.com/chemistry-299"Chemistry Project to Prepare Rayon Threads
From Filter Paper Chemistry Project on Optical Fiber and its Applications
Project Work
Chemistry Project to Study the Rate of Diffusion
Chemistry Project on Foaming Capacity of Soaps
C++ Project on Telephone Directory Management System
C++ Project on Diabetes Detection
C++ Project for Computer Shop
Archives
July 2010
March 2010
July 2009
May 2009
April 2009
March 2009
Tags
Banking C++ Project File C++ Project File Structure CBSE Disaster Management Project CBSE
Maths Project CBSE Maths Project on Probability CBSE Maths Project Topics CD Cafe Disaster
Management
Project
CBSE Maths Project Class IX
CBSE Science Projects Class IX
CBSE Social Science Projects
CCE Projects
Top Contributors
1. Abhisek De
2. Abhyodaya siddhartha
3. Garima Bhardwaj
4. Saurabh
5. Swathi
E D U C O O P
http://educoop.com/http://educoop.com/
http://whos.amung.us/stats/o7vzhgys3357/http://whos.amung.us/stats/o7vzhgys3357/HYPERLI
NK \l "Top
Copyright 2010 School Projects

You might also like