You are on page 1of 5

A July'12 60% SUBMISSION Irfan Qureshi Abdul Waheed Syed Ahmed

Rev. Date Revision(s) Prepared By Reviewed By Approved By



Page 1 of 8
Brendan Clarke
Submitted By
STRUCTURAL
ANALYSIS & DESIGN OF LIGHT POLE FOUNDATION
Job No. 027-T04
Contract No. 027-T04, Task-4
(181-C01, 182-C01, 183-C01)
Doc. No.181-C01-CALCS-20LS-SA-002 REV A
KINGDOM OF SAUDI ARABIA
ROYAL COMMISSION FOR JUBAIL & YANBU
ROYAL COMMISSION IN JUBAIL
ENGINEERING CONSULTANCY SERVICES FOR RIC
TASK-04
CIVIL AND STRUCTURAL
JOB NO. 027T04
Contract No: 027-T04 Designed by: MIQ
Task No: 04 Date : 30/10/2012
Calc No: Design Stage 90% Submittal Checked by: MAW
Subject: Revision: A Date : 30/10/2012
Royal Commission for Juabil & Yanbu
Royal Commision in Jubail
PARTC: ANALYSIS & DESIGN OF LIGHT POLE FOUNDATION
Calculation Sheet
Project Title: Ras Al Khair Industrial City
181-C01-CALCS-20LS-SA-002
LIGHT POLE FOUNDATION
Contract No: 027-T04 Designed by: MIQ
Task No: 04 Date : 30/10/2012
Calc No: Design Stage 90% Submittal Checked by: MAW
Subject: Revision: A Date : 30/10/2012
Royal Commission for Juabil & Yanbu
Royal Commision in Jubail
Calculation Sheet
Project Title: Ras Al Khair Industrial City
181-C01-CALCS-20LS-SA-002
LIGHT POLE FOUNDATION
1. INPUT DATA.
0.150 m
0.100 m
14.000 m
0.2 m
0.25 m
1.2. Soil Data.
20.0 kN/m
3
100.0 kPa
25.0 kPa/m
1.3. Loadings.
15.00 kN
5.00 kN
10.00 kN-m
160.00 km/hr
(kN/m
2
or kPa)
1.3364 kPa
0.6682 kPa
2.1048 kN
2.1. Pole Foundation Embedment and Total Length.
**Trial d = 1.4 m (**iterate until equal to d)
S = 0.8 m
b = 1.131 m
P = 2.807 m
S
3
= 35
kN/m
2
S
3
= S
3a
*d
d = 2.07 m
L
t
= 2.32 m
Pxw = qave*h*(Dt+Db)/2 = (use as Px if no other external horizontal load)
(width of square pole foundation)
P = Px + M/(h+h
1
+h
2
) "equivalent total horizontal load"
d = sqrt(4.25*P*(h+h
1
+h
2
)/(S
3
*b)) IBC 2009 Eq. 18-2 p.398
L
t
= h
1
+ h
2
+ d (total length of pole foundation)
passive pressure based on a depth equal to the depth of embedment
length
b is equal to diameter for circle and diagonal dimension for square
Pole diameter @ bottom, D
b
=
Unit weight of soil, =
*(From SBC or IBC Tables)
Axial load, Py =
Horizontal load, Px =
1.1. Pole Foundation Data.
Depth to resisting surface, h
2
=
Height of Pole, h =
Pole diameter @ top, D
t
=
14.00m HIGH POLE (unpaved areas)
Pole Height above soil, h
1
=
*Allowable soil bearing pressure,P
a
=
*Allow. lat'l soil bearing pressure,S
3a
=
Wind load pressure, q = 2.456x10
-5
V
2
h
2/7
Moment applied, M =
Wind velocity, V =
Horizontal load due to wind, Pxw:
Average q, q
ave
=
q @ top of pole, q
t
=
2. DESIGN CALCULATIONS & RESULTS.
Contract No: 027-T04 Designed by: MIQ
Task No: 04 Date : 30/10/2012
Calc No: Design Stage 90% Submittal Checked by: MAW
Subject: Revision: A Date : 30/10/2012
Royal Commission for Juabil & Yanbu
Royal Commision in Jubail
Calculation Sheet
Project Title: Ras Al Khair Industrial City
181-C01-CALCS-20LS-SA-002
LIGHT POLE FOUNDATION
Ab = 0.64 m
2
Wc = 35.663 kN
Fy = 50.663 kN
Pb = 79.16 kPa
Since,
As
min
=
2016 mm
2
Use 10 16 bars
3.1. International Building Code (IBC 2009).
2.2. Pole Foundation End Bearing Pressure
Ab = S2foundation base area
Wc = Ab * Lt * 24 .. Concrete foundation weight
Fy = Py + Wctoatl vertical load
Pb =fy/Ab actual bearing pressure at bottom
3. REFERENCES.
2.3. Pole Foundation Design
Add 0.0018% minimum reinforcement in the foundation
Pb < Pa, O.K!
Contract No: 027-T04 Designed by: MIQ
Task No: 04 Date : 30/10/2012
Calc No: Design Stage 90% Submittal Checked by: MAW
Subject: Revision: A Date : 30/10/2012
Royal Commission for Juabil & Yanbu
Royal Commision in Jubail
Calculation Sheet
Project Title: Ras Al Khair Industrial City
181-C01-CALCS-20LS-SA-002
LIGHT POLE FOUNDATION
3.2. Saudi Building Code 2007 Section 303 Structural-Soil and Foundations

You might also like