Professional Documents
Culture Documents
com
CCBOOTCAMP’s®
Comprehensive ICND2 Study Guide
With Sample Questions
CCBOOTCAMP®
375 N. Stephanie Street
Building 21, Suite 2111
Henderson, NV 89014
PH# 702-968-5100
www.ccbootcamp.com
“Cisco” the “Cisco Logo,” “CCNA,” “CCNP,” “CCDP,” “CCDA,” “CCIE,” “Cisco
Certified Network Associate,” “Cisco Certified Network Professional,” “Cisco
Certified Design Associate,” and “Cisco Certified Design Professional,” are
registered trademarks of Cisco Systems, Inc. The contents contained herein, are
not associated with nor endorsed by Cisco Systems, Inc.
Published by:
CCBOOTCAMP®
375 N. Stephanie St.
Bldg. 21, Suite 2111
Henderson, NV 89014
All rights reserved. No part of this book may be reproduced or transmitted in any form or by any
means, electronic or mechanical, including photocopying, recording, or by any information
storage and retrieval system, without written permission from the publisher, except for the
inclusion of brief quotations in a review.
Feedback Information
At CCBOOTCAMP®, our goal is to create an easy-to-use reference study guide of the highest
quality and value. User’s feedback is always appreciated and welcome. Please contact us
through email at feedback@ccbootcamp.com with comments and questions.
Contents
Command Review................................................................................................................... 8
VTP Configuration................................................................................................................. 13
Spanning-Tree Configuration................................................................................................ 15
VTP Configuration................................................................................................................. 16
Overview ............................................................................................................................... 42
SPF Algorithm....................................................................................................................... 42
Implementing EGRIP................................................................................................................. 49
ACL Identification.................................................................................................................. 54
Transitioning to IPv6.................................................................................................................. 66
Global Addresses.................................................................................................................. 68
Overview of PPP................................................................................................................... 76
The show interfaces command displays status and statistics information on the network
interfaces of the switch. The table shows some fields in the display that are useful for checking
on fundamental switch details.
Output Description
FastEthernetO/2 is Indicates the status of the interface hardware. In this example, it is
up functioning correctly. The hardware status is followed by the status
of the line protocol, which in this example is also operational and
active.
address is Shows the MAC address that identifies the interface hardware.
0008.a445.ce82...
Half-duplex, 10 Mb/s Shows the type mode of connection. Other possibilities include full
duplex, 100 Mb/s.
CRC Shows that there were 0 CRC errors. CRC errors can indicate
duplex mismatch or a malfunctioning Ethernet adapter in an
attached device.
1. When you use the show interface command to display the status and statistics for the interfaces
configured on a Catalyst switch, which output field indicates the MAC address that identifies the interface
hardware?
B. Hardware is … 10BaseT
C. Address is 0050.BD73.E2C1
show version: Displays the configuration of the system hardware and the software version
information.
show running-config: Displays the current active (running) configuration file of the switch.
This command requires privileged EXEC mode access. The IP address, subnet mask, and
default-gateway settings will be displayed here.
show interfaces: Displays statistics and status information of all the interfaces on the switch.
Both the switch trunks and the switch line ports are considered interfaces. The resulting
output varies, depending on the network for which an interface has been configured. Usually
this command is entered with the options (vpe and slot/number, where type allows values
such as Ethernet and Fast Ethernet, and slot/number indicates slot 0 and the port number on
the selected interface (for example, eO/I).
2. Which show command requires that you have privileged EXEC mode access?
A. show ip
B. show version
C. show running
D. show interfaces
When the correct enable password is entered, the switch or device prompt changes to
hostname#, indicating that the user is now at the privileged EXEC level. Entering the ?
command at the privileged EXEC level will reveal many more command options than those
available at the user EXEC level.
To return to the user EXEC level, enter the disable command at the hostname# prompt.
3. Which Cisco IOS is used to return to the user EXEC mode from the privileged EXEC mode?
A. exit>
B. quit
C. disable>
D. userexec
Command History
Command Description
4. Which command returns to more recent commands in the history buffer after recalling commands?
A. Ctrl-N
B. Ctrl-P
C. show history
D. show terminal
D. Enter both the enable secret and the enable password commands.
6. Which Cisco IOS command configures serial port in slot 0, port 1 on a modular router?
B. interface serial 0 1
D. serial 0 1 interface
Use the clock rate speed (with 64kbps expressed as 64000) command to set the clock speed
of a router.
7. Which Cisco IOS command should you use to set the clock speed to 64 kbps on a serial interface on a
Cisco router?
A. clock rate 64
B. clock speed 64
While Cisco IOS Software is a core technology that extends across many products, its
operation details vary depending on the internetworking devices that are involved. To enter
commands into the CLI, type or paste the entries within one of the several console
configuration modes. In terminal configuration mode, an incremental compiler is invoked. Each
configuration command entered is parsed as soon as you press the Enter key.
8. How do you instruct a Cisco device to parse and execute an entered command?
A. Press the Send key
User Exec: Allows access to only a limited number of basic monitoring commands.
9. Which statement best describes what the user EXEC mode commands allow you to configure on a Cisco
router?
A. You cannot configure anything; the user mode commands are used to display information.
B. The user EXEC mode allows you to perform global configuration tasks that affect the entire router.
C. The user EXEC mode commands allow you to enter a secret password so that you can configure
the router.
D. The user EXEC mode commands allow you to configure interfaces, subinterfaces, lines, and
routers.
Privileged EXEC: allows access to all device commands, such as those used for
configuration and Management, and can be password protected to allow only authorized
users to access the device.
10. Which access level allows a person to access all router commands and can be password protected to
allow only authorized individuals to access the router?
11. Which CLI prompt indicates that you are working in privileged EXEC mode?
A. hostname#
B. hostname>
C. hostname-exec>
D. hostname-config
From the privileged EXEC mode, you can enter global configuration mode using the configure
terminal command. From global configuration mode, you can access specific configuration
modes, which include, but are not limited to, the following:
12. Which configuration mode will you use to configure a particular port on a switch?
A. user mode
______ 1. Line
______ 2. Router
______ 3. Interface
______ 4. Controller
______ 5. Subinterface
A. Router(config-if)#
B. Router(config-line)#
C. Router(config-subif)#
D. Router(config-router)#
E. Router(config-controller)#
Commands that point to or indicate a process or interface that will be configured are called
major commands. When entered, major commands cause the CLI to enter a specific
configuration mode. Major commands have no effect unless a subcommand that supplies the
configuration entry is immediately entered. For example, the major command interface serial
0 has no effect unless it is followed by a subcommand that tells what is to be done to that
interface.
Notice that entering a major command switches from one configuration mode to another.
15. Which command would you enter in the privileged EXEC mode to list the command options?
A. ?
B. init
C. help
D. login
Word help: Enter the ? command to get word help for list of commands that begin with a
particular character sequence. Enter the character sequence followed immediately by the
question mark. Do not include a space before the question mark. The router displays a list of
commands that begin with the characters you entered
16. What CLI command should you enter to display a list of commands that begin with the letter “c” on a
Catalyst switch?
A. c?
B. c?
C. help c
D. help c*
Command syntax help: Enter the ? command to get command syntax help for completing a
command. Enter a question mark in place of a key word or argument. Include a space before
the question mark. The network device then displays a list available command option. “<cr>”
represents a carriage return.
17. What CLI command should you enter to display the command syntax help so that you can see how to
complete a command that begins with “config”?
A. config?
B. config ?
C. help config
D. help config*
Console Error Messages Identifies problems with any switch commands that are
incorrectly entered so that they can be altered or corrected
Command History Buffer Allows recall of long or complex commands or entries for
reentry, review, or correction
18. Match each type of help available with the Cisco IOS CLI to its description
A. Provides a list of commands and the arguments associated with a specific command.
B. Allows recall of long or complex commands or entries for reentry, review, or correction.
C. Identifies problems with router commands incorrectly entered so that you can alter or correct them.
Command Review
Command Description
Ip address address mask Sets the IP address and mask of the device
19. Which Cisco IOS command correctly configures an IP address and subnet mask on a switch?
A. ip address
B. ip address 196.125.243.10
C. 192.125.243.10 ip address
20. Which Cisco IOS commands correctly configure the IP address and subnet mask for Ethernet interface 1
in slot 1?
A. interface Ethernet 1 1
ip address 192.168.1.1 mask 255.255.255.0
C. interface Ethernet 1 1
ip address 192.168.1.1 255.255.255.0
Command Description
21. What information does the show running-config command provide on a Cisco router?
Command Description
22. Which Cisco IOS command creates a message to be displayed upon router login?
A. hostname hostname
Refer to the exhibit. The network administrator made the entries that are shown and then saved the configuration.
From a console connection, what password or password sequence is required for the administrator to access privileged
mode on Router1?
A. cisco
B. sanfran
C. sanjose
D. either cisco or sanfran
E. either cisco or sanjose
F. sanjose and sanfran
1-2
1-3
1-4
1-5
1-6
Ethernet trunk interfaces support different trunking modes. You can configure an interface as
trunking or nontrunking, or have it negotiate trunking with the neighboring interfaces.
D. to load-balance traffic between parallel links using the Spanning Tree Protocol