Professional Documents
Culture Documents
D
00000000
Manufacturer : SUN TEC Corporation.
Address: 431, Dongsam-Dong, Youngdo-Ku, Busan, KOREA. TEL. : +82-51-413-5000 FAX: +82-51-403-7200 E-mail: suntec@kornet.net
1. GENERAL DESCRIPTION
Marine automatic exchange This system is used system, is highly reliable space division and, suitable stored for bad circumstances. program control and fully
solid-state
switching,
accommodates to maximum
20 subscribers
and 2 trunks.
It is designed each.
to operate
- Compact Exchange - Simple Installation and maintenance using High-speed C-MOS technology
- Low Power Consumption - Cost Effectiveness - Console-Iess - Easy System Operation Expansion(10
Lines/SLC
Card)
2. SPECIFICATIONS
2.1 Power Supply
Usually an AC automatically power source is used. If the AC power fails, the power source is
switched
to the auxiliary
OC power
source(battery)
: 220V(10%) : 24V(10%)
60Hz(5%)
OC Input Power
Source
2.3 Signalling
CD
- Make Ratio : 40 3 %
1 -
2.4 DTMF
------Low
High Freq(Hz)
-----Freq(Hz)
1209 1 4 7
1336 2 5 8
O
1477 3 6 9
#
697 770 852 941 - Signal Frequency and Composition - Frequency Oeviation : 1.5 % - Signal Transmission Level
High Frequency Group : -8.0 2.0 dBm Low Frequency Group : -10.0 2.0 dBm
Condition
-5C to +50C 90% or less
Humidity
3. OPERATION
Make sure of a dial tone from telephone heard, it means that all connection handset before dialing. If a busy tone is circuits are busy. In such a case, hook on the
handset and wait tor some time. lf a dial tone is heard, start the dialing within 10 seconds.
3.1 Intercom(lnter-party
Talking)
OIAL COUNTERNO.
number of
counter party(2 digit). When the counter party is free calling party hears a ring back tone until the counter party makes a response. When the counter calling party hears a busy tone. In this case, calling Call-Back". When the conversation is completed party is busy,
and either
handset speech channel will be reset and another party hears a busy tone indicating conversation end.
- 2 -
------------------------
3.2 Paging(Public
Addresser)
Extensions give with paging call priority are permitted aches to the paging equipment by dialing a paging call digit "Broadcast O". "Broadcast O" LOUOSPEAKERS
PUBLlC ADORESSER
This feature allows to make an announcement system is free, speech channel will
through
speaker(s).
be connected
by relay, while
tone(electronic chime bell) is supplied to the telephone and speaker(s) for 2 seconds. In case that paging system is busy, a busy tone is heard from telephone handset.
call
given with this feature priority can make an outgoing call
through trunk by dialing this feature digit "9" and wanted number. After dialing digit "9", make sure of a dial tone from trunk. And then dial the wanted number. If all trunks are busy, a busy tone will be heard. In this case, wait for some time after hook-on and retry later, or make an external call-back.
TRUNK
extension(one,
extension) receives an external ring. The user of pre-assigned extension response to the incoming call by hooking off the telephone
ringing. When an user dials digit "9" to make an external call, if there is a incoming call on a trunk, incoming call is connected firstly.
dials a internal call-back digit "Reserve Oial NO" and wanted internal number. Calling
- 3 -
------------------------
party will hear a ring-back tone from the handset for 1 seconds, indicating internal call-back activated to the called party, then hear a busy tone and speech channel for calling party will be reset.
HOOK_FLASH ANO
If both parties, call-back calling and call-back called, become free, internal call-back calling party receives an internal ring for 30 seconds and will be excluded from
internal call-back service if call-back calling party doesn't make a response within that time by hooking off the telephone handset. If internal call-back calling party makes a response within 30 seconds, he hears a ring-back tone and call-back called party receives an internal ring. Following procedure is the same as that of inter-party call. In case that internal call-back called party is engaged in another call procedure
before call-back calling party makes a response, then the calling party hears a busy tone from the telephone handset when he hooks off in response to internal Call-back ringing. But the internal call-back remains effective.
Call-Back
When making an outgoing call, if all trunks are busy and external calling party wants to make an external call-back, then confirming a dial tone from telephone handset
and dials a external call-back digit "Reserve 9". Calling party will hear a ring-back tone from the handset for 1 seconds, when the external call-back queue indicating external call-back activated. But,
released from speech channel. If any trunk becomes idle, external call-back activated party receives an external ring. By hooking off the handset, external call-back activated party seizures a trunk automatically, and hears a dial tone from trunk. In this case, dialing telephone number only without an external call digit "9" makes an external call. When there are several external call-backs in the queue, priorities will be honored first and then time sequence.
- 4 -
party hears a ring-back tone while counter third party receives an internal ring when the third party is free, or a busy tone when the third party is busy.
In any case, while the transferring party is engaged in cal! transferring the second HOlD by the transferring party restores the speech channel for the external cal! and music wil! be cleared.
external cal! transferring is possible as fol!ows : 1) If the third party is free and makes a response to the cal! from transfer ring party, internal cal! wil! be established. cal! transterring party hooks on, then After confirming external the party's response, is completed.
cal! transfer
Speech channel for the external cal! wil! be connected to the third party.
the third party's ringing(transterring party hooks on, then the ringing
changed from internal ring to external ring, indicating cal! from trunk. External ring continued for 30 seconds. If the third party hooks off within 30 seconds, external cal! is connected to the third party, and if not, external ring tor the
third party stops after 30 seconds. If the extension of transferring party is free at that time, it receives an external ring again for 30 seconds, and if not, the external cal! wil! be released. If transferring party makes a response to the
5 -
SUN TEC.
CORPORATION-----------------------------------------------
4. INSTALLATION
4.1 Installation
The system vibration
of System
be installed in a place where there is little effect of heat, moisture,
must
and shock.
a difficult-to-detect
malfunction
be caused
if a part of the
contacts
the ship body grounding. system uses a microcomputer Never make and, as such, has many semiconductors connection phone). dial illumination, Wrong set. connection etc, or of the power to the
circuits. in case
wrong
telephone
terminal circuit
of system
telephone(key
the exchange
or a telephone
4.3 Connection
Check, at first,
of Telephone
internal wiring
Sets
of telephone consists set. connection of L 1 in white, cord of desk-top type and
compact wall-mount
type telephone
L2 in red.
Connection
method
will be described
Connected No Change
Connection
to Public
Addresser
System
In the exchange,
L1 L2 TELEPHONE PG
L1 L2 A1 A2 SA SPEAKER
EXCHANGE
INBOARD
Voice signal output(L 1, L2) : OdBm Contact signal output(A1, A2) Max. switching voltage: AC 125V, DC 24V Max. switching current: AC/DC 1.25A
- 6 --
-----.
SUN TEC. CORPORATION ----------------------@ Connection of External Relay Box An external bell, if provided separately from the telephone take care of the polarity. @ Connection of Trunks (Shore lines or Inmarsat) The exchange has 2 trunk ports that can be connected Inmarsat(analog telephone follows : port). The connection to Shore lines or to internal bell, must be
L! C.0.1 [
L2 0------------0
L!
CEN1RAL OFFICE
C.0.2
L20---,
INMAR
-SAT
EXC HANG E lERMINAL BOARD
SAW-213B, SAW-213C)
This telephone set has drip-proof type housing case(accommodates circuit network, push-button dials, pilot lamp, bell, relay circuit, headset connector, sub receiver) a handset. To use the wall telephone with headset in a noisy place, sub-receiver type or headchest connector type telephone.
@ Flush Type Telephone(SAF-215A,
network, push button dials, pilot lamp, bell and terminals inside its housing. This telephone set has the terminal for signal relay box. This flush type telephone set is provided with a dimmer S/W. It is used mostly in a wheel house or E.C.R.
7 -
----------------------(SAP-217 A) of drip-proof and structure, has a handset, inside circuit its network, The
@ Portable Type Telephone This telephone push button, set, pilot being lamp
cord-connecting shoulder
receiptable
housing.
connection
Usually,
making
the cord to the cover and lift the handset. for other telephone. Especially for rainy weather, cover. The water-proof ends, close on
while
notch
never
conversation
put hang
up the handset,
cord
pocket and close the cover. cord from the telephone Because the connection set, if necessary.
disconnect
the telephone
CN7~
SLC 1
'~~
CN2 ~
AC220V INPUT
CN3 ~
Public Addresser
[1
DC24V INPUT
Paging
20 21 22 23 24 25 26
27 28
29
30
3'
32
33
34
35
36
37
38
39
Ie
L1
L2
L1 L2 L1 L2 L1 L2
- 8 -
5. TROUBLE
Trouble
SHOOTING
Cause 1. Fuse 1. Replace cord Supply 2. Change 3. Replace 1. Replace line 2. Check 3. Replace 1. Replace 2. Replace Source Measure fuse connection PIS telephone connection CPU CARO
2. Power 3. Power
1. Telephone No tone 2. Connection 3. CPU CARO 1. Telephone No ring 2. SLC CARO 3. Ring Supply 1. Telephone Impossible external cal! 2. Connection 3. CPU CARO 1. Telephone Impossible internal cal! 2. Connection 3. CPU CARO line line
3. Replace of Power Supply Unit 1. Replace 2. Reconnect 3. Replace 1. Replace 2. Reconnect 3. Replace 1. Replace telephone line or pin CPU CARO
The others
- 9 -
410
uv
1_
175
-1
1 !
I I I I I I I I I I
I I I I I I I I I I
. I
(jJ\o*4rA
o
)f'o
(U
o m ..q-
\.O)
Jm
D
o
tJ
u
1 00000000
,---
m r-,
I .-i I
,(
10
170
o
-,
'\
/ @
CABLE ENTRY
01
IUe
e
I
Size
Scale
Doc. No.
Rev
A41/1
Date
. SAS-ATX-001
Sheet: 1 01 1
, 1.0b
2005. 12.
Method
Jumper
EIE
N-N
"'
00<
..
1. Cabling - Signal Input : A- TEL, C- TEL, S- TEL - Power Output : External 8ell. Rotating Lamp - Power source : AC220V/l1 or DC24V (According to the Relay 80x Model.)
av
fA-TEL!
C-TEL! S-TEL
I
SELL +1-
LAMP + 1-
DC24V' V+IV-
L 11 L2 B+ 8- !8+18-
I
Auto Tel.
L1(81) L2(B2)
I I I
'--
*1
REMARK * 1. This voltage must Jumper to L 1, L2 *2. This voltage must *3. This voltage must
be port be be
*2
}
DC24V+ GND(-)
DC24Vor AC2 20V/100V Supply pO wer for Relay Box, Bel!, Lamp
f--
rRotating Lamp
8+
f--
L-
8-
'-r-
r---'--
DC24V+ GND(-)
External Bel!
B+
f--
8-
'--
NOTE: When you use the Relay Box, the voltage of the external Bel! or Rotating Lamp must be same as the Relay Box power source. I Ex) When you use the AC220V for Relay Box power source, you must use the external Bel! or rotating Lamp using the AC220V power source.
ACll0Y 110V
DC24V
A-A', B-B'
-
A-B
O
X
SSR-010
pea
T1
"
'
RL1
o o
o o o o
BELL
CD J3
18]
0,2
o o o o
00000
J4l]
o
o
~
~~tv
o
F1
h
<~<
A-TEL
C-TEL
S-TEL
DC24V
010
l1 l2
010
B+ B-
010
B+ B-
010
+
010
+
010
U+
v-
Ex.l) When use the AC220V power source and connect to the AC220V Bell; Jumper : Power source 220V, J4, A-A', B-B' and don't jump the J3. Ex,2) When use the DC24V power source and using the contact type output; [umper : Power source 24V, J3, A-B and don't jump the J4.
Warning : The output voltage is same as the supply power source. So, when output) . you connect the BeIl or Lamp, you must use the same voltage of power source in Bell or Lamp.(No matter in contact type
Ex) When you use the AC220V power source in relay box, you rnust use the Bell or Lamp using the AC220V voltage.
Warning : Must be check the J3, J4 jumper in above table before operating the relay box by the supply power source. When you mistake in jump of J3, J4, it will be cause to the electric shock and trouble. Don't jump the A' to B'.
~-