Professional Documents
Culture Documents
25 1000
Length 2 3
Breadth 2 2
Depth
Calculation:
Design along Z-direction - Span =Bf Reinforcement provided in top layer Width of Footing Length of Footing Length of Pedestal Depth of Footing Clear Cover Diameter of Reinforcing Bars Area of each bar Effective Depth of Footing slab section Concrete Characteristic Strength Steel Yield Strength
Lf Bf Bp Df cc A deff fck fy
= = = = = = = = = = = = =
Maximum Bearing Pressure among all load qmax cases Corresponding Minimum Pressure qmin
Check for Bending Bending Moment to be checked at face of column (34.2.3.2, IS 456:2000) Factored Bending Moment Limiting Value of Moment Mulim = 0.138*fck*b*deff^2 Percentage of Steel required Minimum Percentage of Steel required Muz Mulim Mu/bdeff2 p pmin Ast Astmin = = = = = = =
Ast = p/100*b*deff Final Area of Steel Required Ast = p/100*b*deff Number of Bars Required Number of Bars Provided
Spacing of the Provided reinforcement
= = = = = = =
Check for One-Way Shear Beam Shear to be checked at distance deff from column face (34.2.4.1, IS 456:2000) Distance of critical section from edge dc = Vuz Shear Force at Section = V Nominal Shear Stress = Cmax = Maximum Allowable shear stress Design Shear strength of Concrete C =
Check for Two-Way (Punching) Shear Punching shear to be checked at distance deff/2 from column face (34.2.4.1 (b) & 31.6, IS 456:2000)
Length of Critical Section, Lcr = Lp + (deff/2)*2 Width of Critical Section, Bcr = Bp + (deff/2)*2
Perimeter of Critical Section, bo = 2(Lcr+Bcr) Column Axial Load Upward Load Due to Pressure Total Load Nominal Shear Stress due to = vertical load, tv1
= = = = = =
tV1
c
= = = = = =
ks = 0.5 + c 1.0
tc
Allowable Shear Stress
0.5 1 1.37
N/mm2 N/mm2
tc*ks 1.37
Design along X-direction - Span =Lf Reinforcement provided in top layer Width of Footing Length of Footing Length of Pedestal Depth of Footing Clear Cover Diameter of Reinforcing Bars Area of each bar Effective Depth of Footing slab section Concrete Characteristic Strength
Lf Bf Bp Df cc A deff fck
= = = = = = = = =
fy
= = = =
Maximum Bearing Pressure among all load qmax cases Corresponding Minimum Pressure qmin
Check for Bending Bending Moment to be checked at face of column (34.2.3.2, IS 456:2000) Mux Factored Bending Moment = Limiting Value of Moment Mulim = Mulim = 0.138*fck*b*deff^2 = Mu/bdeff2 Percentage of Steel required p = Minimum Percentage of Steel required pmin =
Area of Steel Required Ast = p/100*b*deff Minimum Area of Steel Required Ast = p/100*b*deff Final Area of Steel Required Ast = p/100*b*deff Number of Bars Required Number of Bars Provided
Spacing of the Provided reinforcement
= = = = = = = =
Check for One-Way Shear Beam Shear to be checked at distance deff from column face (34.2.4.1, IS 456:2000) Distance of critical section from edge dc = Vuz Shear Force at Section = V Nominal Shear Stress = Cmax = Maximum Allowable shear stress Design Shear strength of Concrete C =
Check for Two-Way (Punching) Shear Punching shear to be checked at distance deff/2 from column face (34.2.4.1 (b) & 31.6, IS 456:2000)
Length of Critical Section, Lcr = Lp + (deff/2)*2 Width of Critical Section, Bcr = Bp + (deff/2)*2
Perimeter of Critical Section, bo = 2(Lcr+Bcr) Column Axial Load Upward Load Due to Pressure Total Load Nominal Shear Stress due to = vertical load, tv1
= = = = = =
tV1
ks = 0.5 + c 1.0
tc
Allowable Shear Stress
= = = = =
0.5 1 1.37
N/mm2 N/mm2
tc*ks 1.37
Check for Overturning Overturning Moment Total vertical Load Leaver Arm Re-storing Moment Factor of Safty against Overturning = = = = = 140 748.875 2000 1497.75 10.7
200 200
4000 2000 500 500 50 12 113.15 432 30 415 101.83 0.102 11.69 0.01
mm mm mm mm mm mm
mm2 mm N/mm2 N/mm2 kN/m2 N/mm2 kN/m2 N/mm2
1.72E+08 1.55E+09
0.46 0.127 0.12 1097.28 1200
mm2 mm2
mm2 %
SAFE
#REF! 1.94E+05
0.225 3.5 0.28
mm N N/mm2 N/mm2
Table 20, IS 456:2000
SAFE SAFE
N/mm2
Table 19, IS 456:2000
6, IS 456:2000)
mm mm mm N
N
4.28E+05 7.21E+04
mm mm mm mm mm mm
mm2 mm N/mm2
4.68E+08 3.26E+09
0.593 0.17 0.12 3019.2 2400 3019.2 26.696 27 70 3053.628 0.172
mm2 %
SAFE
1306 3.99E+05
0.225 3.5 0.32
mm N N/mm2 N/mm2
Table 20, IS 456:2000
SAFE SAFE
N/mm2
Table 19, IS 456:2000
6, IS 456:2000)
mm mm mm N
N
4.42E+05 5.80E+04
1.5
SAFE