Professional Documents
Culture Documents
What three statements are true about routers that are configured for EIGRP?
(Choose three.)
2
Given the following commands:
What three conclusions can be determined based on the commands used on the
router? (Choose three.)
Bandwidth, load, delay, and reliability are metrics used for route selection.
3
What is indicated when an EIGRP route is in the passive state?
The route has the highest path cost of all routes to that destination network.
Cisco-Training.net
The route must be confirmed by neighboring routers before it is put in the active
state.
The route is a feasible successor and will be used if the active route fails.
4
What two problems may occur if the EIGRP default bandwidth for a serial link
is higher than the actual bandwidth? (Choose two.)
Routing updates will arrive too quickly for receiving routers to process.
5
What is the default administrative distance for EIGRP internal routes?
70
90
100
110
120
255
Cisco-Training.net
6
A network administrator issues the command show ip route and sees this line of
output:
What two pieces of information can be obtained from the output? (Choose two.)
Cisco-Training.net
Refer to the exhibit. Which statement is true about the EIGRP authentication
configuration?
RTA and RTB will not accept updates from each other because key 1 on RTB
does not match RTA.
RTA and RTB will not accept updates from each other because the key chain
names do not match.
The ip authentication mode AS does not match the locally configured AS.
8
Which Layer 4 protocol does EIGRP use to provide reliability for the
transmission of routing information?
DUAL
IP
PDM
RTP
TCP
UDP
Cisco-Training.net
Refer to the exhibit. Routers RTR-1 and RTR-3 are completely configured. The
administrator needs to configure the routing protocol on router RTR-2 so that
communication occurs throughout the network. Which group of commands will
successfully configure EIGRP on RTR-2?
10
What prevents RIPv1 updates from being correctly advertised?
11
Cisco-Training.net
What does a router that is running RIP use to determine the best path to take
when forwarding data?
12
What is the purpose of the network command when RIP is being configured as
the routing protocol?
It identifies all of the destination networks that the router is allowed to install in
its routing table.
It identifies the directly connected networks that will be included in the RIP
routing updates.
13
How do EIGRP routers establish and maintain neighbor relationships?
Cisco-Training.net
14
Refer to the exhibit. Routers A and B have EIGRP configured and automatic
summarization has been disabled on both routers. Which router command will
summarize the attached routes?
15
How often does RIPv2 send routing table updates, by default?
every 30 seconds
every 45 seconds
Cisco-Training.net
every 60 seconds
every 90 seconds
16
The Ethernet networks on RTR-2 and RTR-3 were not entered correctly in the
network statements on these routers.
17
What two statements are correct regarding EIGRP authentication? (Choose two.)
Cisco-Training.net
EIGRP authentication uses the MD5 algorithm.
EIGRP authentication requires that both routers have the same key chain name.
EIGRP authentication can be configured on one router and updates from this
router are protected; whereas a neighbor router can be without the authentication
configuration and its updates are unprotected.
18
When should EIGRP automatic summarization be turned off?
19
What is the maximum number of hops that RIP will attempt before it considers
the destination unreachable?
14 hops
15 hops
16 hops
17 hops
Cisco-Training.net
20
What two statements are true regarding EIGRP tables? (Choose two.)
The topology table shows whether a route is in the passive or active state.
The routing table shows the amount of time elapsed since a router adjacency was
formed.
21
Refer to the exhibit. Which statement is true about the output from the show ip
protocols command?
Cisco-Training.net
Auto summarization has been disabled.
Cisco-Training.net