Professional Documents
Culture Documents
SDM140
Features
Simple, compact and heavy duty designed monoblock valves from 1 to 6 sections for open and closed centre hydraulic systems. H Fitted with a direct or pilot operated main pressure relief valve. H Each spool has indipendent load check valve. H Parallel circuit. H Optional carry--over port. H Diameter 18 mm -- 0.71 in interchangeable spools. H A wide variety of service port valves. H Available manual, pneumatic, electro--pneumatic, hydraulic, electro--hydraulic and remote with flexible cables spool control kits.
Additional information This catalogue shows the product in the most usual configurations. Please contact Customer Service Dpt. for more detailled information or special request. WARNING! All specifications of this catalogue refers to the standard product at this date. Walvoil, oriented to a continuous improvement, reserves the right to discontinue, modify or revise the specifications, without notice.
WALVOIL IS NOT RESPONSIBLE FOR ANY DAMAGE CAUSED BY AN INCORRECT USE OF THE PRODUCT.
4th edition January 2000: This edition supercedes all prior documents.
DAT007E
SDM140
Contents
Contents
Working conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Dimensional data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Hydraulic circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Performance data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Ordering codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Inlet relief options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Standard spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 A side spool positioners . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 B side options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Hydraulic spool control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Port rellief options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Inlet and outlet conversion port options . . . . . . . . . . . . . . . 31 Installation and maintenance . . . . . . . . . . . . . . . . . . . . . . . . 32
DAT007E
SDM140
Working conditions
This catalogue shows technical specifications and diagrams measured with mineral oil of 46 mm2/s -- 46 cSt viscosity at 40C temperature. Nominal flow rating Operating pressure (maximum) Max. back pressure Internal leakage A(B)T Hydraulic fluid Fluid temperature Viscosity with NBR seals with FPM (VITON) seals operating range min max Max level of contamination Ambient temperature NOTE -- For different conditions please contact Customer Service. on outlet port T Dp=100 bar - 1450 psi fluid and valve at 40C 80 l/min 280 bar 25 bar 3 cm3/min Mineral base oil from --20 to 80C from --20 to 100C from 15 to 75 mm2/s 12 mm2/s mm2/s 400 from 15 to 75 cSt 12 cSt 400 cSt 4060 psi 360 psi 0.18 in 3/min
DAT007E
SDM140
Dimensional data
46.5 1.83 45 1.77 40.5 1.59 13 0.51
Carry-over
29 1.14
29 1.14
94 3.7
50 1.97
42 1.65 36 1.42
84 3.31
8.5
0.33
40 1.57
11 104.5 4.11
5.5 0.22
Production batch : P99 = production year (1999) 00001 = progressive number Valve code
E
mm 135 180 225 in 5.32 7.09 8.86 mm 118 163 208
F
in 4.65 6.42 8.19
Standard threads
PORTS Inlet P and carry--over C A and B ports Outlet T PILOT PORTS Hydraulic Pneumatic G 1/4 NPTF 1/8--27 SAE 6 (9/16--18 UNF) NPTF 1/8--27 G 1/4 NPTF 1/8--27 BSP
(ISO228/1)
DAT007E
505
505
Weight
kg 9.3 13.4 16.6 lb 20.5 29.5 36.6
E
mm 270 315 360 in 10.63 12.40 14.17 mm 253 298 343
F
in 9.96 11.73 13.50
Weight
kg 20.8 24 27.3 lb 45.9 52.9 60.2
SAE UN-UNF SAE 12 (1 1/16--12 UN) SAE 10 (7/8--14 UNF) SAE 12 (1 1/16--12 UN)
METRIC
(ISO 6149)
SDM140
Hydraulic circuit
Standard configuration with top inlet and outlet ports (PSA execution). P P T A1 B1 A2 B2 T
Positioner kit
175 2540
Ex:
Tank line
SDM140/2--P(YG3--175)/18L/18L/PSA On request the main relief valve can be assembled P on the spool control kit side (VMC execution) T A1 B1
175 2540
A2 B2
Right inlet
Simmetrical body allows the reverse assembly of spools and relative kits (execution ED).
T B2 A2 A2 A1 B1 A1
T
IN
P
175 2540
B2
B1
DAT007E
SDM140
Performance data Open centre
From top inlet to top outlet (execution PSA).
20 (bar) 15 6 sections 4 sections 10 2 sections 90 180
270 (psi)
A1 A2 A3 A4 A5 A6 P B1 B2 B3 B4 B5 B6 T
Pressure
A1 A2 A3 A4 A5 A6
Pressure
15
P B1 B2 B3 B4 B5 B6
180
10
270 (psi)
A1 A2 A3 A4 A5 A6 P B1 B2 B3 B4 B5 B6 T
SDM140
Ordering codes 1st section following section Example: SDM140/ 2 - P (YG3- 175) / 1 8 L / 1 8IM . P2(G3- 100) / PSA * 1. 1. Body kits (*) 2. 3. 4. 5. 6. 7. 8.
Port relief valve setting in bar
TYPE CODE DESCRIPTION Without service port valves prearrangement 1-P 5KC1973000 1 section 2-P 5KC1963000 2 sections 3-P 5KC1923008 3 sections 4-P 5KC1933004 4 sections 5-P 5KC1943004 5 sections 6-P 5KC1953000 6 sections Include body, seals, rings and load check valves.
4.
8
6.
8IM
8.
PSL
9B-10B-11B
2.
page 10 III I
8PN
TYPE CODE DESCRIPTION VMD140/1: direct pressure relief valve type Y (standard) (YG3- 175) X134121175 Range 125 to 250 bar / from 1800 to 3600 psi VMP140/1: pilot operated pressure relief valve type X (XG- 175) X134211175 Range 25 to 280 bar / from 360 to 4060 psi SV XTAP530590 Plug for main relief valve seat
3.
TYPE 1
Spools
CODE 3CU1310401
page 12
8EP3
CIRCUIT DESCRIPTION Double acting, 3 pos., with A and B closed in neutral position 2 3CU1325401 Double acting, 3 pos., with A and B open to tank in neutral position 2H 3CU1325200 Double acting, 3 pos., with A and B partially open to tank 3 3CU1331130 Single acting on A, 3 pos., B plugged: requires G1/2 plug (see part I ) 4 3CU1335130 Single acting on B, 3 pos., A plugged: requires G1/2 plug (see part I ) Special spools: need special body kit J5 3CU1340420 Double acting, 4 pos., with A and B to tank in 4th position (float) 8P 3CU1361400 Double acting, 3 pos., with regenerative in pos.2
8.
PSA 8ED3
1.
4.
TYPE 8 8D 8D1 8K 8MHA 9B 10B 11B 8PN 8EP3 8ED3
page 16 2.
SV
J 13
DESCRIPTION With spring return in neutral position As type 8 for dual control As type 8 for dual control (radial hole) As type 8 for 12 VDC spool solenoid lock device Sping return to neutral spool positioner with ON/OFF spool position signal With detent in pos. 1 and spring return neutral pos. With detent in pos. 2 and spring return neutral pos. With detent in pos. 1 and 2, spring return neutral pos. ON/OFF pneumatic 12 VDC ON/OFF electro-pneumatic 24 VDC ON/OFF electro-pneumatic 12 VDC ON/OFF electro-hydraulic 24 VDC ON/OFF electro-hydraulic
SDM140
Ordering codes 8.
PSA AEK AE
4.
TYPE
page 16
J 13
7.
P U
6.
8IM
J 13K
DESCRIPTION With detent in position 3 and spring return neutral position As type 13 for 12 VDC spool solenoid lock device
5.
TYPE L LB SLP SLC TQ LCB
page 22
II
C
DESCRIPTION Standard lever Steel lever Without lever, with dust-proof plate Without lever, with cap Control for flexible cable Joystick lever for 2 sections
5.
P3T L UX
6.
page 26
J 13IM
5IDR208213
Proportional hydraulic operated with spring return in neutral position Proportional hydraulic operated with extra stroke for float position and spring return in neutral pos.
7. 3.
1-2-2H-3-4 SLP
J 5
page 27
LB
TYPE CODE DESCRIPTION Need special body kit Anti-shock valve P(G3- 100) 3XCAR208113 Range 100 to 250 bar / from 1450 to 3600 psi P(G4- 200) 3XCAR208114 Range 200 to 315 bar / from 2900 to 4600 psi Anti-shock and anti-cavitation valve U(G2- 63) XCAR308112 Range 63 to 125 bar / from 900 to 1800 psi U(G3- 100) XCAR308115 Range 100 to 250 bar / from 1450 to 3600 psi U(G4- 200) XCAR308114 Range 200 to 315 bar / from 2900 to 4600 psi C XCAR408110 Anti-cavitation P3T 3XTAP524290 A and B ports valve blanking plugs Anti-shock and anti-cavitation valve UX(G- 145) X143411145 Range 100 to 280 bar / from 1450 to 4060 psi
SLC 8P TQ
8.
TYPE PSA PSL AE AEK
page 31
2.
X LCB
DESCRIPTION Top inlet and outlet (n.2 G 3/4 plugs required) Side inlet and outlet (n.2 G 3/4 plugs required) G 3/4 carry-over sleeve Plug for closed centre circuit
II
I
TYPE G1/2
Ports plug *
CODE 3XTAP727180 DESCRIPTION For single acting (spools type 3 and 4)
II
Optional handlevers
CODE 170012020 170013120 DESCRIPTION For L lever box L= 200 mm/7.87in For LB lever or LCB joystick L=200mm/7.87in
SV
NOTE J - Spools and positioners with the same symbol must be assembled together: for more informations see relevant pages.
DAT007E
III
TYPE R3,6
Restrictors
CODE 3SPE217060 DESCRIPTION Restrictor 3.6 mm / 0.142 in for G 1/2 port
SDM140
Inlet relief options Direct pressure relief valve VMD140 ( Y G 3 - 175 )
Pressure setting in bar (standard 175 / 2540 psi) Adjustable spring type Adjustment type
(3).
(G, Z).
Adjustment type
G: with screw
Wrench 27 - 42 Nm / 31 lbft Wrench 13 - 24 Nm / 17.7 lbft Allen wrench 6
max 32 1.26
Performance data
Spring nr. 3 *Standard setting: 175 bar -- 2530 psi
300 (bar) Pressure 200 4000 (psi) 3000 2000 100 1000
Response time
(% DP) 105% Pressure 95% 90%
10% 0.25
RESPONSE TIME
0 0 30 Flow 60 90 (l/min)
Time
10
DAT007E
SDM140
Inlet relief options Pilot operated pressure relief valve VMP140 ( X G - 175 )
Pressure setting in bar (standard 175 / 2540 psi) Adjustable type
(G).
Adjustment type
G: with screw
Wrench 27 - 42 Nm / 31 lbft Wrench 13 - 24 Nm / 17.7 lbft Allen wrench 6
max 40 1.57
Performance data
Range setting *Standard setting: 175 bar -- 2530 psi
300 (bar) Pressure 200 (% DP) 4000 (psi) Pressure 3000 2000 100 1000 105% 95% 90%
Response time
10% 0.35
RESPONSE TIME
0 0 30 Flow 60 90 (l/min)
Time
11
SDM140
Standard spool Type 1
B " stroke =
+ 7 mm + 0.28 in
1
A B
P PA
LC
BT
16.5 0.65
50 1.97 40 1.57
1
A
0
B
LC
222.5 8.76
B A stroke =
- 7 mm - 0.28 in
0
A
2
B
P P B
LC
AT
Performance data
Spool metering PA(B)
0.1 90 (l/min ) 60 Flow Flow F 30 Y J Qin = 80 l/min F P(on ports) = 63bar/900psi Y P(on ports) = 100bar/1450psi J P(on ports) = 250bar/3600psi 0.2 (in) 90 (l/min ) 60 J Y 30
0 0 1 2 3 4 Stroke 5 6 7 (mm)
12
SDM140
Standard spool Type 2
A B
1
A
0
B
LC
Type 2H
A B
1
A
0
B
LC
Type 3
Port B plugged
1
A
LC
Type 4
Port A plugged
0
B
LC
DAT007E
13
SDM140
Spool options Type 5
This spool needs special body with extra machinering and must be used only with spool positioner type 13, 13K (see page 21). A B
+ 7 mm + 0.28 in P T
1
A B
" stroke = T P PA A LC P T
BT B
1
A
0
B
LC
0
A
2
B
A T P P B A LC P T
stroke = - 6.7 mm - 0.26 in P T
AT B
2
A
3
B
AA T P LC P T
stroke = - 12 mm - 0.47 in P T
A(B) T (float)
Performance data
Spool metering PA(B)
0.1 90 (l/min ) 60 Flow F 30 Y J Qin = 80 l/min F P(on ports) = 63bar/900psi Y P(on ports) = 100bar/1450psi J P(on ports) = 250bar/3600psi Flow 0.2 (in) 90 (l/min ) 60 J 30 Y F
0 0 1 2 3 4 Stroke 5 6 7 (mm)
14
SDM140
Spool options Type 8P
This spool needs special body with extra machinering.
B " stroke =
+ 7 mm + 0.28 in
1
A B
P PA
LC
BT
1
A
0
B
LC
B A stroke =
- 7 mm - 0.28 in
0
A
2
B
LC
PA+B (regenerative)
Performance data
Spool metering PA
(Q = 80 l/min) 0.1 0.2 (in) 90 (l/min ) 60 Flow F 30 Y J Qin = 80 l/min F P(on ports) = 63bar/900psi Y P(on ports) = 100bar/1450psi J P(on ports) = 250bar/3600psi 50 (bar) 40 Pressure drop 30 20 10 0 0 30 60 Flow 90 120 (l/min) 200 600 (psi) 400
0 0 1 2 3 4 Stroke 5 6 7 (mm)
DAT007E
15
SDM140
A side spool positioners With spring return in neutral position
8 kit
Supplied with standard spring type B (see force--stroke diagram). Available with lighter spring type A (8MA code: 5V08108240) or heavier type C (8MC code: 5V08208000).
1
Allen wrench 4 6.6 Nm / 4.9 lbft Allen wrench 6 24 Nm / 17.7 lbft
2
- 0.2 150 (N) 75 Forza 0 -75
Force-stroke diagram
- 0.1 0.1 0.2 (in)
C B A A B C
-7 -6 -5 -4 -3 -2 -1 0 1 Stroke 2 3 4 5 6
(lbf) 30 20 10 - 10 - 20 - 30
50 1.97
-150
7 (mm)
8D kit 1
Allen Wrench 4 6.6 Nm / 4.9 lbft Wrench 15 24 Nm / 17.7 lbft
8D1 kit 0 2
Allen Wrench 4 6.6 Nm / 4.9 lbft Wrench 14 24 Nm / 17.7 lbft 8H11
M8
13 0.51
62.5 2.46
71 2.80 81 3.19
8K kit
35 1.38
Connection ISO4400 (for connector see page 19) Wrench 24 9.8 Nm / 7.2 lbft Allen wrench 4 6.6 Nm / 4.9 lbft Allen wrench 6 24 Nm / 17.7 lbft Wrench 14 24 Nm / 17.7 lbft 100 3.94
115 4.53
NOTE -- In case of P, U and C port relief valves assembly, the coil needs to be turned 15 due to limited space. 16
DAT007E
SDM140
A side spool positioners Sping return to neutral spool positioner with ON/OFF spool position signal
8MHA kit
Module kit with electric ON/OFF signal to indicate the spool position. Moving the polarized magnet connected to the spool, a Hall effect sensor will be actuated creating a low current output.
Printed circuit with Hall effect sensor + 3/28 Vdc Out 1 3 1 2 Out 2 103 2.62 Connection DIN43650 Digital outputs PNP open collector.
Polarized magnet Allen wrench 6 24 Nm / 17.7 lbft 40 1.57 Allen wrench 4 6.6 Nm / 4.9 lbft 0.2 28 Voltage (V) 0.1
Out 1
0 - 0.1 - 0.2 (in) 28 Voltage (V) 0.2 0.1
Out 2
0 - 0.1 - 0.2 (in)
0 7 6 5 4 3 2 1 0 -1 -2 -3 -4 -5 -6 -7 (mm) Stroke
0 7 6 5 4 3 2 1 0 -1 -2 -3 -4 -5 -6 -7 (mm) Stroke
With detent
9B-10B-11B kits
Allen wrench 4 6.6 Nm / 4.9 lbft Wrench 6 24 Nm / 17.7 lbft
11B
Operating features
Locking force in position 1 and 2: . . . . . 135 N / 30.4 lbft 10% Unlocking force from position 1: . . . . . . 210 N / 47.2 lbft 10% from position 2: . . . . . 300 N / 67.5 lbft 10% 82,5
9B
10B
Operating features
Locking force: 135 / 30.4 lbft 10% Unlocking force: 210 N / 47.2 lbft 10%
Operating features
Locking force: 135 N / 30.4 lbft 10% Unlocking force: 300 N / 47.2 lbft 10%
DAT007E
17
SDM140
A side spool positioners 8ED3 kit
ON--OFF electro--hydraulic spool control kit with external pilot and drain.
Allen wrench 4 6.6 Nm / 4.9 lbft 42 1.65 73 2.87 6.6 Nm Connection ISO4400 (for connector see page 19) Solenoid valve: wrench 24 - 9.8 Nm / 7.2 lbft
Scheme
L V
Coil
1
Scheme ISO 1219
170 6.69
Wrench 9
L V
24 Nm 17.7 lbft
1
V Wrench 13 24 Nm / 17.7 lbft 169 6.65 L
Operating features
Pilot pressure . . . . . . . . . . . . . . . . . . . : min.10 bar- 145 psi : max.50 bar - 725 psi Max.back pressure on outlet L . . . . . : 25 bar - 363 psi DESCRIPTION 3 ways solenoid valve 12VDC coil 24VDC coil
Ordering codes
CODE 2S0EJ08002013 2X4350012 2X4350024
P A1 B1 A2 B2
T L
A1
A2
IN
T
175 2540
B1
B2
DAT007E
SDM140
A side spool positioners
Collector kit with pilot and drain lines
The kit consists of a collector with VRP pressure reducing valve and relative pipes.
202 7.95 24 0.95
VRP
T A1 B1 A2 B2
A1
A2
175 2540
VRC
P
B1
Wrench 32 42 Nm / 31 lbft VRC back pressure valve (not included in kit)
B2
Ordering codes
TYPE KE1R3 KE2R3 KE3R3 KE4R3 KE5R3 KE6R3 CODE 5KE1R30330 5KE2R30330 5KE3R30330 5KE4R30330 5KE5R30330 5KE6R30330 DESCRIPTION Kit for 1 section Kit for 2 sections Kit for 3 sections Kit for 4 sections Kit for 5 sections Kit for 6 sections
Ex: SDM140/2--P(YG3--175)/18ED3L/18ED3L/VRC-KE2R3-24VDC
Pressure drop PT
400 (psi) 300 200
10
100
G3/4
0 0 30 Flow 60 90 (l/min)
Operating features
50 1.97
2 1
PG09 DAT007E
19
SDM140
A side spool positioners 8PN kit
1
Allen wrench 4 6.6 Nm / 4.9 lbft Special wrench 24 Nm / 17.7 lbft V1 V2
NPT 1/8
V1 V2
Operating features
Pilot pressure . . . . . . . . . . . . . . . . . . . : 6 bar (max.10) : 87 psi (max.145) 120 4.72
8EP3 kit
Scheme
V1 Connector C01 code: 2X1001020 (include in control kit) Wrench 14 9.8 Nm / 7.2 lbft 34 73 1.34 2.87 Pg 9 V2
1
Scheme ISO 1219
1
V1 142.5 5.61 8 0.32 V2
V1
V2
Operating features
Pilot pressure . . . . . . . . . . . . . . . . . . . : 6 bar (max.10) : 87 psi (max.145)
20
DAT007E
SDM140
A side spool positioners For spool type 5 (page 14)
13 kit 1 0 2 3
Operating features
Locking force . . . . . . . . . . . . . . . . . . . . : 330 N / 74.2 lbf 10% Unlocking force . . . . . . . . . . . . . . . . . . : 240 N / 54 lbf 10%
82.5 3.25
13K kit
Connection ISO4400 (for connector see page 19) Wrench 24 9.8 Nm / 7.2 lbft Allen wrench 4 6.6 Nm / 4.9 lbft
35 1.38
Operating features
115 4.53 Locking force . . . . . . . . . . . . . . . . . . . . : 330 N / 74.2 lbf 10% Unlocking force . . . . . . . . . . . . . . . . . . : 240 N / 54 lbf 10%
NOTE -- In case of P, U and C port service valves assembly the coil needs to be turned 15 due to limited space.
DAT007E
21
SDM140
B side options L lever box
Alluminium with protection boot lever pivot box; it can be rotated 180 (execution L180)
0
Vertical handlever assembly
28 17
17
3
Horizontal handlever assembly
execution L180
LB steel lever
19 0.75
Execution LB1
44.5 1.75
Execution LB4
34.5 1.36
65.5 2.58
29 1.14
220220--1
220230-1
220230-1
SLC cap
Protection cap usable with pneumatic spool and electro--hydraulic control kit.
5 0.2
1
9 0.35 27 1.06
17 0.67
75 2.95
22
29 1.14
SDM140
B side options TQ cable remote control
Waterproof cap prearranged for remote control with flexible cable.
1
Allen wrench 4 6.6 Nm / 4.9 lbft Wrench 10 Wrench 24
97.5 2.84
NOTE - For more information concerning remote cable control require appropriate documentation.
CD flexible cables
DAT007E
23
SDM140
Bside options LCB joystick lever
Allen wrench 4 9.8 Nm / 7.2 lbft Wrench 17 42 Nm / 31 lbft Wrench 13
1 1
0 0
2 2
Wrench 12
B1
B1-B2 B2-B1
B2
B2-A1
29 1.14
A2
B2
B1
A1
22 0.87
15,9 0.63
A1-A2 M12
A1-B2
A2-B1
A2-A1
A1
45 1.77
12 0.47
A2
97 3.82
A1
A1-A2 A1-B2 A2-B1
A2
A2-A1
A2
42 1.66 29 1.14
B2
B1
A1
B1-A2
B1
12 0.47
B1-B2
B2-B1
B2-A1
B2
NOTE - Due to limited space in case of LCB3 or LCB4 configuration the assembly of ports service relief valves is not possible. 24
DAT007E
SDM140
Hydraulic spool control 8IM kit (for single acting and double acting spools)
Allen wrench 4 6.6 Nm / 31 lbft Allen wrench 5 9.8 Nm / 7.2 lbft 59 2.32 G 1/4 VA
1
59 2.32
2
VB
VA
VB
Operating features
Max.pilot pressure . . . . . . . : 50 bar : 725 psi
77 3.03
2
30 (bar) Pilot pressure 20
77 3.03
0.1
10
100
0 -7 -5 -3 -1 0 1 Stroke 3 5 7 (mm)
13IM kit (for spool type 5 with 4th float position see page 14)
Allen wrench 4 6.6 Nm / 4.9 lbft Allen wrench 5 9.8 Nm / 7.2 lbft 59 2.32 G 1/4 VA
3
VB
VA
76,5 3.01
VB
88,5 3.48
77 3.03
Pressure-stroke diagram
3
30 (bar) Pilot pressure 20
Float
- 0.4 - 0.3
Port B
- 0.2 - 0.1
Port A
0.1
10
100
0 -12
-10
-8
-6
-4
-2
0 Stroke
6 (mm)
DAT007E
25
SDM140
Hydraulic spool control Connection example
\
VA1
VA2 P
VA1
VB1
VA2
VB2 A2 B2
13IM kit
8IM kit
A1 B1
A1
A2
IN
B1
B2
175 2540
VB1
VB2
Spool control kit 13IM pressure curve 070 for float position 0.2 0.24 0.3 (in) 0.04 0.1
400 (psi) 300
15 5
0 0 1 3 Stroke 6
218
16.8 5.8
0 0
244
200 100
73
84
8.5 9
(mm)
3 Stroke
9 (mm)
26
DAT007E
SDM140
Port relief options Anti-shock valve P 1 ( G 3 - 100 )
Setting value in bar. Spring type (3, 4). Adjustment type (G, H).
P1
A B T P
P2
A B
P3
A B T P
1 2 3
Adjustment type
G: with screw
Wrench 22 42 Nm / 31 lbft Notch 1,5 mm / 0.06 in Wrench 24 42 Nm / 31 lbft max 95,5 3.76 Special body prearranged for port service valves
Performance data
Spring nr. 3 (blue band) *Standard setting: 100 bar -- 1450 psi
400 (bar) 300 Pressure 200 100 0 0 30 Flow 60 90 (l/min) (psi) 4500 3000 1500
Spring nr. 4 (red band) *Standard setting: 200 bar -- 2900 psi
400 (bar) 300 Pressure 200 100 0 0 30 Flow 60 90 (l/min) (psi) 4500 3000 1500
Response time
(% DP) 105% Pressure 95% 90%
10% 0.18
RESPONSE TIME
Time
27
SDM140
Port relief options Anti-shock and anti- cavitation U 1 (G 3 - 100 )
Setting value in bar. Adjustment type (G, Spring type (2,
3, 4). H).
U1
A B T P
U2
A B
U3
A B T P
1 2 3
Adjustment type
G: with screw
Wrench 22 42 Nm / 31 lbft Notch 1,5 mm / 0.06 in Wrench 24 42 Nm / 31 lbft max 95,5 3.76 Special body prearranged for port service valves
Performance data
Spring nr. 2 (green band) *Standard setting: 63 bar -- 900 psi
400 (bar) 300 Pressure 200 100 0 0 30 Flow 60 90 (l/min) (psi) 4500 3000 1500
Spring nr. 3 (blue band) *Standard setting: 100 bar -- 1450 psi
400 (bar) 300 Pressure 200 100 0 0 30 Flow 60 90 (l/min)
Spring nr. 4 (red band) *Standard setting: 200 bar -- 2900 psi
(psi) 4500 3000 1500
400 (psi) (bar) 4500 300 3000 1500 Pressure 200 100 0 0 30 Flow 60 90 (l/min)
Response time
(% DP) 105% Pressure 95% 90%
OVERSHOOT
Pressure drop
60 (bar) Pressure 40
20
10% 0.45
RESPONSE TIME
0.6
TRANSIENT RECOVERY TIME
Time
()
0 0 10 20 Flow 30 40 (l/min)
28
SDM140
Port relief options Anticavitation valve C 1
1 2 3
mounted on A port. mounted on B port. mounted on A and B ports.
C1
A B T
C2
A B
C3
A B T P
86 3.39
Performance data
Pressure drop
24 (bar) 18 Pressure 12 6 0 0 30 Flow 60 90 (l/min)
P1T
A B T P
Special body prearranged for port service valves
P2T
A B
P3T
A B T P
Wrench 10 42 Nm / 31 lbft
DAT007E
29
SDM140
Port relief options Pilot operated pressure valve
The UX cartridge valve cavity is different from the P, U and C valves cavity
UX 1 ( G - 145 )
Pressure setting in bar Adjustment screw
UX1
AB T P
UX2
AB
UX3
AB T P
(G, H)
1 2 3
Adjustment type
G: with screw
Wrench 22 42 Nm / 31 lbft Wrench 17 40 Nm / 30 lbft Allen Wrench 5 Wrench 24 42 Nm / 31 lbft max 115.5 4.55
Performance data
Range setting *Standard setting: 145 bar -- 2100 psi
(psi) 4500 3000 1500
Pressure drop
60 (bar) Pressure 40 750 (psi) 500 250 (% DP) 105% Pressure 95% 90%
Response time
20
10% 0.2
RESPONSE TIME
Time
SDM140
Inlet and outlet port options PSA: upper (standard)
See page 6
PSL: side
Allen wrench 12 - 42 Nm / 31 lbft Allen wrench 12 42 Nm / 31 lbft
A1 B1
A2 B2
P P T
175 2540
Ex: SDM140/2--P(YG3--175)/18L/18L/PSL
P A1 B1 A2 B2
C C
G3/4
175 2540
Ex: SDM140/2--P(YG3--175)/18L/18L/AE
G3/4
P T
Closed centre plug Allen wrench 12 42 Nm / 31 lbft
T A1 B1 A2 B2
Ex: SDM140/2--P(YG3--175)/18L/18L/AEK
175 2540
DAT007E
31
SDM140
Installation and maintenance
The SDM140 valve is assembled and tested as per the technical specification of this catalogue. Before the final installation on your equipment, follow the below recommendations: ---the valve can be assembled in any position, in order to prevent body deformation and spool sticking mount the product on a flat surface; in order to prevent the possibility of water entering the lever box and spool control kit, do not use high pressure wash down directly on the valve; prior to painting, ensure plastic port plugs are tightly in place.
A2 A1 B2 B1 C T
Carry-over configuration
NOTE -- These torque are recommended. Assembly tightening torque depends on many factors, including lubrication, coating and surface finish. The manufacturer shall be consulted. 32
DAT007E
SDM140
Installation and maintenance
O-Ring seals 18x2,5 code: 4GUA118025 Load check valves Sealing edge
Body
Lever pivot box Pressure relief valve Spool Normally the spools are interchangeable. Verify the smoothness during the assembly
NOTE -- All articulated parts inside cap, lever box and mechanical joystick are lubricated with synthetic base grease grade NLGI2 MALFUNCTION External leakage pivot box lever or control kit side. Excessive internal leakage on A and B ports. Dropping load during transition while raising Inability to build pressure on A and B ports. CAUSE Worn spool seal due to mechanical actuation or high back pressure. Increase clearance between spools and body due to high wear High leakage on the load check valve. Pressure relief valve blocked open. Low pump pressure and flow. REMEDY Locate the leakage and replace the seal. Check back pressure level. Replace the directional control valve and check the oil contamination level. Remove the load check valve and clean the seat. Remove and clean or replace the valve. Check the pump and circuit.
DAT007E
33
SDM140
Note
NOTE -- The SDM140 valve can be supplied with one coat of black paint (CVN configuration). EX.: SDM140/2--P(YG3--175)/18L/18L/PSA-- <CVN>
34
DAT007E
AUSTRIA
IRELAND
PORTUGAL
BELGIUM
ISRAEL
CANADA
ITALY
CHINA
DENMARK
SOUTH AFRICA HYFLO Southern Africa ltd P.O. box 240 Paarden eiland 7420 tel. 0027 21 511 7021 fax. 0027 21 5114456 LOWE ERNEST 6 Skew road 1460 Boksburg North tel. 0027 11 8944281 fax. 0027 11 8946108 SPAIN INTERSEAL S.A. Autovia de Castelldefels Km 5 08820 El prat de Llobregat Barcelona tel. 0034 93 3706711 fax. 0034 93 3701807 HYDRAC AB Getaengsvaegen 22 50263 Boras tel. 0046 33 127470 fax. 0046 33 125879
FINLAND
FRANCE
SWEDEN
GERMANY
SWITZERLAND BT HYDRAULIK AG Fischermattelistrasse 6 3000 Berna 5 tel. 0041 31 3798141 fax. 0041 31 3823980 TAIWAN LIMIT TEIN INDUSTRIAL CO. LTD 2F. NO. 8-1 lane 42 sec.3 TZU Ching rd. Sanchung city Taipei Hsien tel. 00886 2 9995022 fax. 00886 2 9995055 SRITONG ENGINEERING CO. LTD 8/233-236 Moo 4 Rama 2 10150 Bangmod chomthong, Bangkok tel. 00662 428 4171 fax. 00662 428 4180 AFRICA INDUSTRIE N.Z.I Ben Arous Tunis tel. 0021 61 1 384510 fax. 0021 61 1 384476 HIDRO KONTROL MAK. SANAYI VE TI Buyuk Sanayi 1 Cadde Arpacio 2 Ishani n. 95/11 Iskitler 6060 Ankara tel. 0090 312 3842895 fax. 0090 312 3414476 HIDROTAS DIS TICARET A.S. Halit Ziya bulv n.33 Zuhal is han-Izmir tel. 0090 232 4842253 fax. 0090 232 4837463 UNITED KINGDOM BYPY HYDRAULICS & TRANSMISSIONS LTD NO. 8 Lingen road sheet R.I.E. Ludlow salop sy8 1xd tel. 0044 1 584 873012/3/4 fax. 0044 1 584 876647 USA MC ELROY FLUID POWER 826 North Fulton 74158 Tulsa Oklahoma tel. 001 918 8369055 fax. 001 918 8319300
THAILAND
TUNISIA
HOLLAND
MALAYSIA
TURKEY
MOROCCO
NORWAY
NEW ZELAND VICKERS SYSTEMS LTD 77-79 Ben Lomond Crescent P.O.Box 51 076 Pakuranga Aoukland tel. 0064 9 576 9089 fax. 0064 9 576 5865
WALVOIL S.P.A. 42100 REGGIO EMILIA ITALY VIA ADIGE, 13/D TEL. +39.0522.932411 FAX +39.0522.300984 E-MAIL: INFO@WALVOIL.COM HTTP: //WWW.WALVOIL.COM CUSTOMER SERVICE TEL. +39.0522.932555 FAX +39.0522.932455
D1409808I DAT007E