Professional Documents
Culture Documents
TECHNICAL MANUAL
(ML-104858)
(115/60/3)
SPECIFICATION SHEET
INSTALLATION INSTRUCTIONS
OPERATION INSTRUCTIONS
CLEANING INSTRUCTIONS
MAINTENANCE INSTRUCTIONS
TROUBLE SHOOTING INSTRUCTIONS
WIRING DIAGRAMS
CATALOG OF REPLACEMENT PARTS
SMARTPARTS USER GUIDE
RECOMMENDED SPARE PARTS LIST
Warranty Registration
Preventive Maintenance
Specialty Programs
Item # ________________________________
Quantity _______________________________
C.S.I. Section 11400
A-200
MIXER
FOOD EQUIPMENT
STANDARD FEATURES
MODEL
Gear-Driven Transmission
15 Minute Timer
Three Fixed Speeds
Open Base
Large, Easy-To-Reach Controls
#12 Taper Attachment Hub
Stainless Steel Bowl Guard
OPTIONS
Deluxe Nickel Chrome Plate Finish
(115/60/1 and 230/60/1, Bench Model only)
Floor Model
(Base is 21"W x 2112"D x 4114"H)
ACCESSORIES
A-200 MIXER
A-200
MIXER
FOOD EQUIPMENT
SOLUTIONS/BENEFITS
Recommended Maximum Capacities - dough capacities based on 70F. water and 12% flour moisture.
AGITATORS
SUITABLE FOR
OPERATION
CAPACITY OF BOWL (QTS. LIQUID)
Egg Whites
D
Mashed Potatoes
B&C
Mayonnaise (Qts. of Oil)
B or C or D
Meringue (Qts. of Water)
D
Waffle or Hot Cake Batter
B
Whipped Cream
D or C
Cake, Angel Food
(8-10 oz. cake)
C or I
Cake, Box or Slab
B or C
Cake, Cup
B or C
Cake, Layer
B or C
Cake, Pound
B
Cake, Short (Sponge)
C or I
Cake, Sponge
C or I
Cookies, Sugar
B
Dough, Bread or Roll
(Lt.-Med.) 60% AR
ED
Dough, Heavy Bread 55% AR
ED
Dough Pie
B&P
Dough, Thin Pizza 40% AR
(max. mix time 5 min.)
ED
Dough, Med. Pizza 50% AR
ED
Dough, Thick Pizza 60% AR
ED
Dough, Raised Donut 65% AR
ED
Dough, Whole Wheat 70% AR
ED
Eggs & Sugar for Sponge Cake
B & C or I
Icing, Fondant
B
Icing, Marshmallow
C or I
Shortening & Sugar, Creamed
B
Pasta, Basic Egg Noodle
(max. mix time 5 min.)
ED
PRODUCT
A-200
20
1 qt.
15 lbs.
10 qts.
112 pts.
8 qts.
4 qts.
15
20 lbs.
20 lbs.
20 lbs.
21 lbs.
15 lbs.
12 lbs.
15 lbs.
25 lbs.
15 lbs.
18 lbs.
9 lbs.
10 lbs.
20 lbs.
9 lbs.*
20 lbs.
8 lbs.
12 lbs.
2 lbs.
16 lbs.
5 lbs.
1st Speed
* 2nd Speed
If high gluten flour is used, reduce above dough batch size
by 10%.
2nd Speed should never be used on 50% AR or lower products.
USE OF ICE REQUIRES A 10% REDUCTION IN BATCH SIZE.
1 gallon of water weighs 8.33 lbs.
NOTE: Attachment hub should not be used while mixing.
A-200
MIXER
FOOD EQUIPMENT
SPECIFICATIONS
MOTOR:
1
2 H.P., Hobart designed, permanently lubricated ball
bearings, splash-proof, fan cooled. Single-phase is
capacitor-start, induction-run type.
Single Phase
115V
230V
8.2 Amps
4.2 Amps
ELECTRICAL:
115/60/1 and 230/60/1 U L Listed. Also available in
100/50/1, 220/50/1, 100/60/1 and 220/60/1 not
submitted for U L Listing.
CONTROLS:
Two-pole toggle switch with No Volt Release.
A 15-minute electric timer is standard. Non-timed
operation obtained by setting timer on HOLD
position.
TRANSMISSION:
Gear-driven. Gears are constant mesh heat-treated
alloy steel. Anti-friction ball bearings. A hardened
steel worm and special worm wheel transmit power
from motor to transmission. Grease lubricated.
SPEEDS:
Three positive speeds - Low, Intermediate, and High.
Agitator
(RPM)
Attachment
(RPM)
Low
107
61
Intermediate
198
113
High
361
205
BOWL GUARD:
Heavy-duty stainless steel wire front and solid stainless steel rear portion. Front portion of guard rotates
easily to add ingredients and install or remove
agitator. It detaches in seconds for cleaning in dishwasher or sink. Rear portion of guard can be quickly
cleaned in position. Guard must be in closed position
before mixer will operate. The bowl support lock
prevents the bowl from being lowered while mixer
is running. Bowl support interlock provides further
protection.
BOWL LIFT:
Hand crank operated, self-locking in any position.
FINISH:
Standard Metallic Gray finish, Polyurethane Enamel.
Deluxe finish has nickel-chrome plating on transmission case, bowl support, pedestal and base.
STANDARD EQUIPMENT:
Consists of the mixer unit with cord and plug, one
(1) 20-quart stainless steel bowl, one (1) B flat
beater, one (1) D wire whip, stainless steel bowl
guard, cord and plug.
ATTACHMENT HUB:
When specified, comes with front-mounted Hobart
standard #12 taper attachment hub for use with
#12 size attachments.
NOTE: Use of attachment hub during mixing
operation may result in a negative impact on
performance and longevity of mixer.
ATTACHMENTS AND ACCESSORIES:
The following are available at extra cost:
Stainless Steel Bowl
B Flat Beater
Stainless Steel B Beater
C Wing Whip
D Wire Whip
E Dough Hook
ED Dough Hook
P Pastry Knife
Hobart Bowl
Scraper
Hobart Ingredient
Chute
A-200
MIXER
FOOD EQUIPMENT
SPECIFICATIONS
ELECTRICAL SPECIFICATIONS: 115/60/1 and
230/60/1 U L Listed. Also available in 100/50/1,
220/50/1, 100/60/1 and 220/60/1 not submitted for
U L Listing.
A200/A200-T Mixers
WARNING
ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH
THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE
AND/OR OTHER CODES IN FORCE.
A200FT Mixer
WARNING
ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH
THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/
OR OTHER CODES IN FORCE.
As continued product improvement is a policy of Hobart, specifications are subject to change without notice.
N
S
R
U
C
T
O
N
S
A200 MIXER
MODEL
A200
937 332-3000
www.hobartcorp.com
2
A200 Mixer 115/60/1 Technical ManualPage 8 of 43
GENERAL
The model A200 mixer is a 20 quart, bench-type mixer with a 1/2 H.P. motor, and a #12 attachment hub.
With the use of special agitators, a 12 quart bowl may be used on the A200 mixers.
The floor model and the deluxe finish model are equipped with a timer.
Most A200 mixers are equipped with a 0 - 15 minute timer.
There are a variety of attachments and accessories available for all models, and these are explained
in a separate Use and Applications Handbook which is supplied with each mixer.
INSTALLATION
UNPACKING
Immediately after unpacking the mixer, check for possible shipping damage. If this machine is found
to be damaged after unpacking, save the packaging material and contact the carrier within 15 days of
delivery.
Prior to installation, test the electrical service to assure that it agrees with the specifications on the
machine data plate.
LOCATION
Place the mixer on a suitable sturdy level surface. There should be adequate space around the mixer
for the user to operate the controls and install and remove bowls.
Holes are provided in the base to permanently secure the mixer, although this is not necessary in
normal installations. Four plastic plugs are supplied with the mixer to plug these holes if they are not
used.
3
A200 Mixer 115/60/1 Technical ManualPage 9 of 43
OPERATION
WARNING: MOVING BEATER IN BOWL. KEEP HANDS, CLOTHING, AND UTENSILS OUT WHILE
IN OPERATION, DO NOT USE WITHOUT INTERLOCKED GUARD.
CONTROLS
All models are furnished with an On-Off toggle switch which controls power to the mixer.
The Bowl Guard must be in position or the mixer will not operate. Refer to page 6.
If the Bowl Support is not all the way up, the mixer will not operate unless the On-Off switch is held in
the up position.
The TIMER (if equipped) is used in conjunction with the On-Off switch for timed mixing operations and
will stop the mixer when the desired time has elapsed.
With the timer set on HOLD, the mixer will run until the On-Off switch is turned to Off.
The GEAR SHIFT LEVER (Fig. 1) is used to change speeds. Always stop the mixer before changing
speeds. To change speeds, turn the switch Off, move the gear shift lever to the desired speed, and
turn the switch back On.
Speed 1 (Low) This speed is for heavy mixtures such as bread dough, heavy batters, and
potatoes.
Speed 2 (Medium) This speed is for light dough which must rise quickly, cake batters, and some
whipping operations.
Speed 3 (High) This is a fast speed for light work such as whipping cream, beating eggs, and
mixing thin batters.
The BOWL LIFT HANDLE (Fig. 1) is used to raise and lower the bowl. To raise the bowl, rotate the
handle upward; rotating the handle downward lowers the bowl.
MIXING
This section explains operation of the mixer and how to install bowls, agitators, and attachments. A
separate Use and Applications Handbook is provided with the mixer which contains information on
mixing procedures and outlines specific uses for agitators, attachments, and accessories.
Bowl
New mixer bowls and agitators (beaters, whips, and dough arms) should be thoroughly washed with
hot water and a mild soap solution, rinsed with either a mild soda or vinegar solution, and thoroughly
rinsed with clear water BEFORE being put into service. This cleaning procedure should also be
followed for bowls and agitators before whipping egg whites or whole eggs.
The bowl must be installed before the agitator. To install the bowl, fully lower the bowl support (Fig. 1).
Position the bowl so the alignment bracket on the back of the bowl is in the bowl retainer and the
alignment pins (Fig. 1) on the front of the bowl support fit in the holes on the sides of the bowl. Lock
the bowl in place by rotating the bowl clamps (Fig. 1) over the ears of the bowl.
Agitator
To install an agitator (Fig. 1), the bowl must be installed and fully lowered. Place the agitator in the bowl,
push it up on the agitator shaft, and turn it clockwise to seat the shaft pin in the slot of the agitator shank.
4
A200 Mixer 115/60/1 Technical ManualPage 10 of 43
A200
ON
ON
7
8
10
OFF
11
LD
OFF
12
13
HO
15 14
ATTACHMENT HUB
THUMB SCREW
CONTROL
PANEL
BOWL LIFT
HANDLE
SPLASH
GUARD
GEAR SHIFT
LEVER
APRON
WIRE CAGE
BOWL
SUPPORT
AGITATOR
BOWL
CLAMP
BOWL LIFT
SLIDEWAYS
ALIGNMENT
PIN
PL-53477
Fig. 1
5
A200 Mixer 115/60/1 Technical ManualPage 11 of 43
Front-Center
Retainer
To Remove:
Rotate Wire Cage to the Left 340 Degrees until
the Front-Center Retainer can be lowered
Flat
Fig. 2
6
A200 Mixer 115/60/1 Technical ManualPage 12 of 43
CLEANING
WARNING: UNPLUG MACHINE POWER CORD BEFORE BEGINNING ANY CLEANING
PROCEDURE.
The mixer should be thoroughly cleaned daily.
Bowls and agitators should be removed from the mixer and cleaned in a sink.
DO NOT use a hose to clean the mixer it should be washed with a clean damp cloth. The apron
(Fig. 1) may be removed by loosening the thumb screws.
The Drip Cup-Splash Guard (which is secured by three screws) should be removed periodically and
wiped clean.
For cleaning the Bowl Guard (including both Wire Cage Assembly and Splash Guard), refer to page 6.
MAINTENANCE
WARNING: UNPLUG MACHINE POWER CORD BEFORE BEGINNING ANY MAINTENANCE
PROCEDURE.
LUBRICATION
Bowl Clamps (Fig. 1) should be lubricated twice a year.
Motor
The motor has sealed ball bearings which require no lubrication maintenance.
7
A200 Mixer 115/60/1 Technical ManualPage 13 of 43
SERVICE
If service is needed on this equipment, contact your local Hobart Service Office.
8
A200 Mixer 115/60/1 Technical ManualPage 14 of 43
PRINTED IN U.S.A.
TROUBLESHOOTING
A200 MIXER
SYMPTOM
POSSIBLE CAUSE
1.
2.
3.
4.
NOTE:
If symptom(s) persists after possible causes have been checked, contact your local Hobart Service Office.
1CR
4
ES
2 START 3
SWITCH
1
1S
ON/OFF
3
2LS
BOWL
1CR
6
NO
1LS
1CR INTERLOCK
0
1
GRN
TIMER
MOTOR
J1
GND
BLK
WHT
MOTOR
START
1 2
MAIN
T4
T1
SPLICE
K1
TIMER CONTACTS
CLOSED
OPEN
OFF 1-2 & 1-3
--1-2
HOLD
1-3
--TIMED
1-2 & 1-3
WIRING DIAGRAM
A-200-T MIXER
UNDER 150 VOLTS
AI 2657
CATALOG OF
REPLACEMENT
PARTS
MODEL A200
SERIES MIXER
(INCLUDES MOTOR PARTS)
A200
A200 DT
A200 FT
A200 C
ML-104858
ML-104863
ML-104861
ML-134091
1 THRU 4
11
7
8
ON
9-10
1
11
0
13
OFF
15
14
PL-55803
PART NO.
00-294650-004-1
00-294650-004-2
00-294650-004-3
00-294650-004-4
00-291746
00-875567
00-873115-00001
SC-013-07
00-123109
SC-128-68
00-291748
NAME OF PART
AMT.
-2-
HOBART
1-2
PL-55796
3
CORRECTIONAL COVER
(ML-134091 ONLY)
ILLUS.
PL-55796
1
2
3
PART NO.
00-875153
SC-128-66
00-438151
NAME OF PART
AMT.
Cover .......................................................................................................................................... 1
Mach. Screw 8-32 x 1/2 Tx. Button Hd. (SST) ........................................................................... 3
Hasp Plate ............................................................................................................................... 1
-3-
1-2
10
11
12
13-14
15
16
4
6
PL-55793
PART NO.
SC-066-13
SC-128-73
00-438533
00-438523
SC-122-44
00-438530
00-438527-00001
00-438526
SC-122-82
00-438527-00003
SC-122-44
00-438539
00-438525
SC-122-83
00-438527-00002
SC-122-44
NAME OF PART
AMT.
Mach. Screw 8-32 x 1/4 Phil. Truss Hd. (Painted and Deluxe) .................................................. 3
Mach. Screw 8-32 x 1/4 Tx. Button Hd. (SST) (ML-134091) ..................................................... 3
Guard & Drip Cup Assy. ............................................................................................................. 1
Wire Cage Weldment .................................................................................................................. 1
Mach. Screw Special 8-32 x 3/8 Truss Hd. ................................................................................ 2
Stop Cage ................................................................................................................................ 1
Shoe Front ............................................................................................................................... 1
Key Shoe ................................................................................................................................. 1
Mach. Screw 4-40 x 7/16 Oval Hd., Special ................................................................................ 1
Shoe Adjustable ...................................................................................................................... 1
Mach. Screw Special 8-32 x 3/8 Truss Hd. ............................................................................. 2
Bumper Cage ........................................................................................................................... 1
Retainer Magnet ...................................................................................................................... 1
Mach. Screw 6-32 x 3/8 Truss Hd., Special ............................................................................... 2
Shoe Fixed .............................................................................................................................. 1
Mach. Screw Special 8-32 x 3/8 Truss Hd. ............................................................................. 2
-4-
20
19
21
22
23
24
9 THRU 18
25
34
26-27
8
33
7
6
32
28
29
PL-55801
31
30
PART NO.
00-114824-00001
00-435047-00004
00-435047-00007
00-435047-00004
OR-001-03
SC-119-07
WL-019-79
00-108197-00001
00-012746-00019
00-012746-00005
00-012746-00006
00-012746-00007
00-012746-00008
00-012746-00009
00-012746-00010
00-012746-00012
00-012746-00013
00-012746-00016
00-435065-00002
RR-004-18
00-012430-00055
00-015217
BB-018-17
00-007094
BA-002-09
00-023166-00013
00-023166-00006
BB-005-34
00-023482
00-113936
00-065062-00001
SC-040-09
WL-003-35
00-438524-00002
00-102778-00001
NAME OF PART
AMT.
2
1
3
4
5
6-7
9-10
11
PL-55802
BASE UNIT
-6-
BASE UNIT
ILLUS.
PL-55802
1
2
3
4
5
6
7
8
9
10
11
PART NO.
00-873229-00003
00-873229-00002
00-108159
WS-018-19
SC-097-53
WS-018-19
SC-062-27
00-074998-00004
WS-018-19
SC-118-10
00-875590-00003
NAME OF PART
AMT.
-7-
56-57
1
2
3
7-8-9
5
4
10-11-12
13
14-15
16-17
19
20
18
21
23
22
24
32
54
55
33
34
35
36
25
26
48-49
53
27
47
52
50
51
28
46
29
42
37 THRU 41
30
31
43
44
45
PL-55800
-8-
PART NO.
SC-060-40
00-087711-00248
00-439892
00-275683
00-295644
00-270776
WL-006-22
SC-041-13
SC-120-38
WL-006-22
SC-011-95
SC-123-34
00-873232-00001
00-438543-00002
00-438543-00004
00-070641-00011
SC-128-73
00-078506
PC-003-55
PS-004-15
00-114430-00002
WS-009-11
WS-009-13
00-438528
00-015215
WS-006-46
PC-003-55
00-012745
00-012782
WS-006-26
NS-036-15
00-479510
SC-022-20
SC-014-55
00-111213-00006
00-111213-00005
00-113016-00001
00-113016-00004
00-113016-00005
00-113016-00006
00-113016-00007
00-121625
SC-060-56
SC-128-81
00-078505
00-478582
00-084854-00001
00-084853-00003
00-084853-00005
00-291444-00001
00-291444-00002
00-291263
00-274614
00-087711-252-1
00-875859
00-438079
00-438078
NAME OF PART
AMT.
4-5-6
2-3
7
8
63
14-15
62
9-10
61
11
12
13
16
17
18-19
60
59
58
57
20-21
56
55
22
54
23
24
36
53
51
52
37
25-26-27
50
46 THRU 49
45
42
43
44
41
40
28
39
38 35 34 33
31
32
29
30
- 10 -
PL-55799
PART NO.
00-018231-00003
SC-016-17
SC-015-57
SC-128-82
NS-009-36
00-875751
SC-018-01
00-012708
00-020394-00001
00-875752
00-020395
00-011800-00062
00-012735
00-873802-00005
00-873802-00006
00-438131-00057
WL-003-28
SC-127-85
00-479486
SC-009-49
SC-128-68
00-115231-00002
00-118363
FE-022-84
00-117542-00081
00-117542-00082
00-117542-00080
00-077401
00-875241
00-479471
SC-015-34
SC-128-75
00-290115-00001
00-023946
PS-003-08
BA-002-09
00-111170
NS-013-22
WL-004-06
00-013160
00-873504
00-012733
00-012734
00-012732
00-875567
00-123109
SC-027-28
WL-011-01
NS-010-11
00-873115-00002
00-873140-00001
00-873140-00002
00-123674
00-011800-00116
WL-003-28
SC-119-07
00-067750
NS-009-36
SC-008-56
00-064871
WL-003-28
SC-008-48
WL-003-22
00-875249
00-479470
NAME OF PART
AMT.
2
3-4
1
5
6
7
9
10
11
12
17
14
13
15
16
18-19-20
PL-55560
21-22
MOTOR PARTS
- 12 -
MOTOR PARTS
ILLUS.
PL-55560
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
PART NO.
NS-032-23
00-012430-00004
00-291221
00-070407
00-012754
00-012757
00-873057
SD-015-38
00-271612-00002
00-873203-00002
SD-015-38
00-873125
SD-015-39
WL-008-07
00-087714-042-1
00-087714-042-3
SD-015-38
00-873061-00001
00-873061-00002
00-873061-00003
00-113703
00-070487-00025
NAME OF PART
AMT.
- 13 -
32
45
8
9
33
46
10
34
11
47
35
48
12
36
13
37
49
14
38
15
16
17
18
50
51
39
52-53
40
19
41
54
42
20
21
43
55
44
56
22
23
24
25-26
27
28
29
30
PL-55483
31
- 14 -
PART NO.
NS-032-29
WS-008-13
BB-020-18
WS-010-18
WS-010-19
WS-010-20
00-107145
00-124730
00-109070-00002
00-124729
00-124732
00-124752
00-124733-00002
00-124744
00-012695
00-012430-00059
00-070035-00001
00-012695
00-124743
00-012723
BB-020-06
00-012430-00017
00-067500-00075
00-124734
00-437342
00-067500-00078
00-114695
00-124946
WS-030-83
00-010928-00002
00-024715-00003
00-012710
WS-006-36
BB-005-02
00-012744
00-291236
00-124736
00-435297
00-012697
00-435297
00-124760
RR-004-19
BB-005-01
SL-002-08
00-012710
WS-006-36
BB-005-02
00-124745
00-124765-00001
00-124748
00-012430-00004
00-124751-00003
00-124749-00002
00-291128
BB-005-01
SL-002-08
00-292799-00002
00-292800
00-292798-00001
00-292798-00002
NAME OF PART
AMT.
- 15 -
1-2
5-6
PL-55897
AGITATORS
ILLUS.
PL-55897
1
2
3
4
5
6
7
PART NO.
00-275459
00-275559
00-295165
00-275897
00-477521
00-295119
00-295036
NAME OF PART
AMT.
APRIL 2005
PRINTED IN U.S.A.
User Guide
User Guide
From
hobartservice.com
select
PARTS
Next
select
SMARTPARTS
Web Browser Pop-up blocker must be turned off for this site in order for SmartParts to operate
If the ML Number of
the Equipment is
known,
select
Use SmartParts Now
(Well explain what to
do if the ML number of
the Equipment is not
known in Section 2)
This is SmartParts
home page
Then click on
Continue
Click on the
Radio button
to select the
Parts Catalog
Selecting the part on the figure causes the part to be highlighted on the parts list
Click on the Add button to add the part to the shopping cart
You can add more parts or change the quantity of the parts already in the cart
When finished, click on the Confirm Parts Selected and then on Print Parts List if
you want to print
Then click on
Continue
Selecting the part on the figure causes the part to be highlighted on the parts list
Click on the Add button to add the part to the shopping cart
You can add more parts or change the quantity of the parts already in the cart
When finished, click on the Confirm Parts Selected and then on Print Parts List if
you want to print
A200 MIXER
SEPTEMBER 2009
Part Number
Description
291221
Worm
124751-3
124734
Planetary Shaft
120388
Switch, Timed
70487-18
Capacitor
271612-2
87714-42-1
Relay 120V
87711-248
438527-1
Front Shoe
438527-3
Adjustable Shoe
438539
Cage Bumper
438525
Magnet Retainer
438527-2
Fixed Shoe
113936
Beater Shaft
Page 1 of 1
A200 Mixer 115/60/1 Technical ManualPage 43 of 43
A200 Mixer