Professional Documents
Culture Documents
Condux’s sole liability and the purchaser’s sole remedy for a failure of goods
under this limited warranty, and for any and all claims arising out of the
purchase and use of the goods, shall be limited to the repair or replacement
of the goods that do not conform to this warranty.
CONDUX
Condux International, Inc. • P.O. Box 247 • 145 Kingswood Road • Mankato, MN 56001 USA
1-507-387-6576 • 1-800-533-2077 • FAX 1-507-387-1442
Internet: http://www.condux.com • e-mail: cndxinfo@condux.com
5 Blue Heron Drive Collegeville, PA 19426 (610) 831-5020 Fax: (610) 831-5012
www.comstarsupply.com
5 Blue Heron Drive
Comstar Supply, INC Collegeville, PA 19426
Think Cable... Think Comstar Phone: 610-831-5020
Fax: 610-831-5012
1-866-326-6782 www.comstarsupply.com
Installation Procedure
NOTE: For use of pulling cables prior to lashing. 8. Attach the pulling rope to the eye at the front of the
NOTE: Do not exceed 300 lbs. of pulling pressure per cable. Cable Puller.
NOTE: Cable Puller 18108000 is used for 1/4" (6 mm) 9. Proceed with the cable pulling process. The Cable Puller
and 5/16" (8 mm) strand capacities. Cable Puller will have to be removed at each pole and placed on the
18108010 is used for 5/16" (8 mm) and 3/8" (10 mm) next strand section for continuous cable placement.
strand capacities.
NOTE: Also called “jig” and “airplane”.
1. Install from the bucket or the pole.
Removal Procedure
2. Release the brake by pushing the lever upwards and
1. Remove the Cable Puller after the lashing has been
holding it in that position.
completed on the section of cable that the Cable Puller
3. Place the Cable Puller on the strand with the eyelets facing is holding.
the opposite direction in which the cable is to be pulled.
2. Reverse the installation procedure to remove the
4. Hang the Cable Puller on the strand by placing the rollers Cable Puller.
over the strand.
5. Release the brake lever. The brake should now pinch the
strand and hold the puller in place. The brake will release Rollers
Eyelets
when the pulling begins and catch when the pulling stops.
This will hold the unit in place and keep the cable from
creeping back down the strand.
Eye
6. Place Cable Grips over the ends of the cable that is to
be pulled.
Brake
7. Attach the Cable Grips to the quick-connect links on the
Cable Puller. The eyelets swivel during the pulling process Quick-Connect Links
to avoid tangles and possible cable damage. The eyelets
are set to break at 300 lbs. of pulling pressure. Figure 1. Aerial Cable Puller
!WARNING: Read and understand all procedure !CAUTION: Wear personal protective equipment:
and safety instructions before using any Condux hard hat, safety glasses, safety shoes, and leather
Aerial Cable Pullers. Failure to do so may result in work gloves. Failure to do this could result in
personal injury or property damage. Save this personal injury.
user’s guide for future reference.
ADVERTENCIA !ADVERTENCIA: Favor de leer y comprender !DANGER: Do not use around electrical wires.
todas las instrucciones de operación y seguridad Severe personal injury or death could result.
antes de usar el Condux Aerial Cable Pullers. Si
Instrucciones
de Operación Ud. nocomprende las instrucciones favor de
consultarle a su jefe.
5 Blue Heron Drive Collegeville, PA 19426 (610) 831-5020 Fax: (610) 831-5012
www.comstarsupply.com