Professional Documents
Culture Documents
DIN
Wide choice of variants DSNU- Cylinder barrel made of stainless steel Bearing and end caps made of wrought aluminium alloy
DSNUP- Cylinder barrel made of wrought aluminium alloy Bearing and end caps made of polyamide Cost optimised
DSNU/ESNU-MA Threaded bearing cap Short end cap with axial supply port
DSNU-MQ Threaded bearing cap Short end cap with lateral supply port
DSNU-MH Direct mounting on bearing cap Short end cap with lateral supply port
Cushioning types Cushioning P Mode of operation The drive is fitted with flexible polymer end position cushioning Small loads Low speeds Low impact energy No adjustment required Time-saving Cushioning PPS The drive is fitted with self-adjusting end position cushioning Small to medium loads Low to medium speeds Medium impact energy No adjustment required Time-saving Powerful Cushioning PPV The drive is fitted with adjustable end position cushioning Medium to large loads High speeds High impact energy Very powerful
Application
Advantages
Internet: www.festo.com/catalog/...
Key features S2 S6 S10 Through piston rod Heat resistant seals Constant (slow speed) operation at low piston speeds Low friction
Description For working at both ends with the same force in the advance and return stroke, for attaching external stops Temperature resistance up to max. 120 C Suitable for slow stroke movements at a constant, stick-slip-free speed over the full stroke of the cylinder. Seal contains silicone grease (not free of paint-wetting impairment substances) The special seals considerably reduce system wear. This corresponds to a considerably lower response pressure. Seal contains silicone grease (not free of paint-wetting impairment substances) Metric standard thread to ISO All external cylinder surfaces comply with corrosion resistance class 3 to Festo standard 940 070. The piston rod is made from corrosion and acid resistant steel
S11
K2 K3 K5 K6 K8 R3
Extended male piston rod thread Female piston rod thread Special thread on piston rod Shortened male piston rod thread Extended piston rod High corrosion protection
Longer service life with bellows kit DADB The bellows kit is a leak-free system. To prevent unwanted media from being drawn in, the supply and exhaust air of the kit must be ducted via a pressure compensation hole in the connection section 1. The kit protects the piston rod, seal and bearing against a wide variety of media, for example: dust chippings oil grease fuel
Internet: www.festo.com/catalog/...
Female thread
[mm] Doubleacting
[mm]
[mm]
S2
K8
K2
K6
K5
K3
Basic version with position sensing (cylinder barrel made of stainless steel) DSNU 8, 10 10, 15, 20, 25, 1 100 30, 35, 40, 50, 1 200 12, 16 60, 70, 80, 100, 1 320 20 125, 150, 160, 1 500 25 200, 250, 300, 320, 400, 500 DSNU Round cylinder with piston 32 63
Basic version with or without position sensing (cylinder barrel made of aluminium) DSNUP 16 25, 50, 100 2) 20 25
8, 10 12, 16 20 25
8, 10 12, 16 20 25
8, 10 12, 16 20 25
Internet: www.festo.com/catalog/...
S6
S10
S11
R3 12
Basic version with position sensing (cylinder barrel made of stainless steel) DSNU
DSNU Round cylinder with piston 32 63 Basic version with or without position sensing (cylinder barrel made of aluminium) DSNUP
dsnu
23
26
dsnu
12
dsnu
12
dsnu
12
dsnu
Internet: www.festo.com/catalog/...
Female thread
[mm] 10, 25, 40, 50, 80, 100, 125, 160, 200, 250, 300, 320, 400, 500
S2
K8
K2
K6
K5
K3
Function
Version
Piston
Stroke
Variable stroke1)
Cushioning Fixed P
Position sensing A
[mm] Singleacting Basic version with position sensing ESNU 8, 10, 12, 16, 20, 25
[mm] 1 50
1 50
ESNU-MA Round cylinder with piston 32 63 Basic version without position sensing ESN 8, 10, 12, 16, 20, 25
10, 25, 50
1 50
1)
Cylinders with position sensing require a minimum stroke of 10 mm to ensure reliable sensing
Internet: www.festo.com/catalog/...
S6
S10
S11
R3 45
Version
esnu
38
ESNU-MA Round cylinder with piston 32 63 Basic version without position sensing ESN
esnu
51
2)
Internet: www.festo.com/catalog/...
aI
aC aH 1 2 aF 3 4 5 bJ aB aD aE aG
6 7 8 Variants DSNU-MQ
DSNU-MA
DSNU-MH
DSNU-Q
DSNU-KP
Swivel mounting
Installation variants with mounting attachments Foot mounting (for short strokes) Foot mounting
Flange mounting
Swivel mounting
Internet: www.festo.com/catalog/...
-H1)
Note 2) Only push-in fittings or one-way flow control valves with cylindrical connecting thread (M or G thread) may be used for the compressed air ports in conjunction with the DSNUP. 3) The bellows kit protects the cylinder (piston rod, seal and bearings) against a wide range of media and thus prevents premature wear. It can only be used in combination with an extended piston rod (K8).
Cannot be used on the bearing cap in combination with bellows kit DADB.
Internet: www.festo.com/catalog/...
DSNU Type Double-acting DSNU/DSN Single-acting ESNU/ESN Piston [mm] Stroke [mm] Cushioning P PPV PPS Flexible cushioning rings/pads at both ends Pneumatic cushioning, adjustable at both ends Pneumatic cushioning, self-adjusting at both ends Standard cylinder
25
80
PPV
MQ
Standard cylinder
Position sensing A Variant MQ MA MH Lateral air connection Axial air connection With mounting flange on bearing cap Via proximity sensor
Modular product system Individually configurable DSNU 34 ESNU 43 Square piston rod (protection against rotation) Through piston rod (piston rod type) Extended male piston rod thread Male piston rod thread, shortened at one end Female piston rod thread (female thread) Special piston rod thread (special thread) Extended piston rod at front Clamping unit on the piston rod Heat-resistant seals for temperatures up to 120 C (temperature resistance) Slow speed (constant motion at low piston rod speeds) Low friction All external cylinder surfaces conform to corrosion resistance class CRC 3 (corrosion protection)
10
Internet: www.festo.com/catalog/...
Internet: www.festo.com/catalog/...
11
-N-T-
Basic version
Direct mounting MH
General technical data Piston Pneumatic connection Piston rod thread Constructional design
10
12
16
20
25 Gx M10x1.25
Cushioning
[mm] [mm]
M5 M5 M5 M5 Gx M4 M4 M6 M6 M8 Piston Piston rod Cylinder barrel Flexible cushioning rings/pads at both ends Adjustable cushioning at both ends Self-adjusting cushioning at both ends 9 12 15 12 15 Via proximity sensor Direct mounting (MH variant only) Via accessories Any
17 17
-H- Note: This product conforms to ISO 1179-1 and to ISO 228-1
Operating conditions Piston Operating medium Note on operating/pilot medium Operating pressure Basic version S10 S11
1)
10
12
16
20
25
[bar]
Compressed air in accordance with ISO 8573-1:2010 [7:4:4] Operation with lubricated medium possible (in which case lubricated operation will always be required) 1.5 101) 1 10 1.5 10 1 10 0.45 10 0.3 10
Ambient conditions Standard cylinder Ambient temperature1) Corrosion resistance class CRC2) ATEX [C]
Basic version
S6
S10 +5 +80 2
S11 2
R3 20 +80 3
12
Internet: www.festo.com/catalog/...
1) 2)
Note operating range of proximity sensors. Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents. Corrosion resistance class 3 as per Festo standard 940 070 Components requiring higher corrosion resistance. External visible parts in direct contact with industrial atmospheres or media such as solvents and cleaning agents, with a predominantly functional requirement for the surface.
Internet: www.festo.com/catalog/...
13
16 10 100
20
25
2.7 3.2
5.3 4.7
<11) <11)
10 47 40 0.05
12 68 51 0.07
Theoretical force at 6 bar, ad30 vancing Theoretical force at 6 bar, re23 tracting Max. impact energy at the end positions 0.03 for flexible cushioning elements1)
1) The values are reduced by approx. 50% at an ambient temperature of 80 C
Average piston speed v as a function of applied load m in combination with PPS cushionings Piston 16 Piston 20
-H-
Note
-H-
Note Additional graphs for PPS cushioning www.festo.com Design software for PPV cushioning ProDrive
14
Internet: www.festo.com/catalog/...
8 34.6 2.4
10 37.3 2.7
12 75 4
16 89.9 4.6
20 186.8 7.2
25 238 11
Basic version
8/10 12/16 20 25
Standard cylinder 1 2 3 4 Piston rod Bearing cap Cylinder barrel End cap Seals Note on materials
Basic version
R3
S6
S10
S11
High-alloy stainless steel Anodised aluminium High-alloy stainless steel Anodised aluminium Polyurethane, nitrile rubber RoHS compliant
Fluoro elastomer
Internet: www.festo.com/catalog/...
15
-H+ [mm] 8 10 12 16 20 25 [mm] 8 10 12 16 20 25 6 8 11 6 9 12 46 50 56 68 69.5 4 6 6 8 10 8.2 23 31 2 22 24 28 18 16 64 75 82 95 104 12 16 20 22 KW AM B h9 12 16 22 BE BF CD H9 4 6 8 D D4 9.3 11.3 13.3 17.3 21.3 26.5 VD EE EW G
Note
Piston rod nut is not included in scope of delivery for 8 20. = plus stroke length KK KV
12 17 20 22 MM
15 20 27
8 M5 12 Gx 16 16 10
M4 M6 M8 M10x1.25 ZJ
19 24 32
L2
PL
TO
WF
XC 1
62 72 78 92 97.5
5 7 9
-H- Note: This product conforms to ISO 1179-1 and to ISO 228-1
16
Internet: www.festo.com/catalog/...
+ [mm] 8 10 12 16 20 25 [mm] 8 10 12 16 20 25 7.6 7.1 7.7 14.5 14 5 6 7.5 14 18.1 22.4 25.2 12 16 22 25 M3 M4 M5 18 23 31 3.4 4.5 5.5 6.6 16 22 28 32 8 B h9 12 16 22 D2 10.5 12.5 14.5 17.5 21.7 26.7 L4 D3 E EE F FB G
= plus stroke length L2 -MQ -MA 43.6 43.1 47.7 53.7 66.5 68.5 ZJ -MQ 62 -MA 59.6 59.1 69.7 75.7 90.5 96.5 -MH 61.5 61.8 72 77.8 91.5 97.2 -MH 53.5 53.8 62 67.5 81.5 86.2
6 8 10 11 L5
24 M5 30 40 Gx 3
46 50 56 68 69.5 WF
L3
RT
10 11
72 78 92 97.5
-H- Note: This product conforms to ISO 1179-1 and to ISO 228-1
Internet: www.festo.com/catalog/...
17
-H-
Note
The thread types at both piston rod ends are identical. In combination with variant Q, the left-hand piston rod end is square, the right-hand piston rod end round. K2 Extended male piston rod thread K6 Shortened male piston rod thread
-H-
Note
If variant K8 is required in combination with S2, the piston rod will only be extended on one side.
[mm] 8 10 12 16 20 25
1)
A1 max.
A2 max.
A3 max.
AM
AF
KF Basic thread
T4
WF -MQ
15 20 25 35
12 16 20 22
12
M4 M6
M4 M6 M8 M10x1.25
2 2.6
16 22 24 28
62 72 78 92 97.5
The special threads are only available as male threads. The scope of delivery does not include a hex nut for the piston rod thread.
18
Internet: www.festo.com/catalog/...
Stroke [mm] 10 15 20 25 30 40 50 60 80 100 10 15 20 25 30 40 50 60 80 100 10 15 20 25 30 40 50 60 80 100 125 160 200 10 15 20 25 30 35 40 50 60 70 80 100 125 150 160 200
P Flexible cushioning rings/pads at both ends A With position sensing Part No. Type 19177 1908247 1908248 19178 1908249 19179 19180 1908250 19181 19182 19183 1908251 1908252 19184 1908253 19185 19186 1908254 19187 19188 19189 1908255 1908256 19190 1908257 19191 19192 1908258 19193 19194 19195 19196 19197 19198 1908259 1908260 19199 1908261 1908262 19200 19201 1908263 1908264 19202 19203 19204 1908265 19205 19206 DSNU-8-10-P-A DSNU-8-15-P-A DSNU-8-20-P-A DSNU-8-25-P-A DSNU-8-30-P-A DSNU-8-40-P-A DSNU-8-50-P-A DSNU-8-60-P-A DSNU-8-80-P-A DSNU-8-100-P-A DSNU-10-10-P-A DSNU-10-15-P-A DSNU-10-20-P-A DSNU-10-25-P-A DSNU-10-30-P-A DSNU-10-40-P-A DSNU-10-50-P-A DSNU-10-60-P-A DSNU-10-80-P-A DSNU-10-100-P-A DSNU-12-10-P-A DSNU-12-15-P-A DSNU-12-20-P-A DSNU-12-25-P-A DSNU-12-30-P-A DSNU-12-40-P-A DSNU-12-50-P-A DSNU-12-60-P-A DSNU-12-80-P-A DSNU-12-100-P-A DSNU-12-125-P-A DSNU-12-160-P-A DSNU-12-200-P-A DSNU-16-10-P-A DSNU-16-15-P-A DSNU-16-20-P-A DSNU-16-25-P-A DSNU-16-30-P-A DSNU-16-35-P-A DSNU-16-40-P-A DSNU-16-50-P-A DSNU-16-60-P-A DSNU-16-70-P-A DSNU-16-80-P-A DSNU-16-100-P-A DSNU-16-125-P-A DSNU-16-150-P-A DSNU-16-160-P-A DSNU-16-200-P-A
PPV Pneumatic cushioning, adjustable at both ends A With position sensing Part No. Type
10
12
16
1908266 1908267 1908268 33973 1908269 1908270 19229 19230 1908271 1908272 19231 19232 19233 1908273 19234 19235
DSNU-16-10-PPV-A DSNU-16-15-PPV-A DSNU-16-20-PPV-A DSNU-16-25-PPV-A DSNU-16-30-PPV-A DSNU-16-35-PPV-A DSNU-16-40-PPV-A DSNU-16-50-PPV-A DSNU-16-60-PPV-A DSNU-16-70-PPV-A DSNU-16-80-PPV-A DSNU-16-100-PPV-A DSNU-16-125-PPV-A DSNU-16-150-PPV-A DSNU-16-160-PPV-A DSNU-16-200-PPV-A
Internet: www.festo.com/catalog/...
19
Stroke [mm] 10 15 20 25 30 35 40 50 60 70 80 100 125 150 160 200 250 300 320 10 15 20 25 30 35 40 50 60 70 80 100 125 150 160 200 250 300 320 400 500
P Flexible cushioning rings/pads at both ends A With position sensing Part No. Type 19207 1908282 1908283 19208 1908284 1908285 19209 19210 1908286 1908287 19211 19212 19213 1908288 19214 19215 19216 19217 34718 19218 1908305 1908306 19219 1908307 1908308 19220 19221 1908309 1908310 19222 19223 19224 1908311 19225 19226 19227 19228 34719 35191 35192 DSNU-20-10-P-A DSNU-20-15-P-A DSNU-20-20-P-A DSNU-20-25-P-A DSNU-20-30-P-A DSNU-20-35-P-A DSNU-20-40-P-A DSNU-20-50-P-A DSNU-20-60-P-A DSNU-20-70-P-A DSNU-20-80-P-A DSNU-20-100-P-A DSNU-20-125-P-A DSNU-20-150-P-A DSNU-20-160-P-A DSNU-20-200-P-A DSNU-20-250-P-A DSNU-20-300-P-A DSNU-20-320-P-A DSNU-25-10-P-A DSNU-25-15-P-A DSNU-25-20-P-A DSNU-25-25-P-A DSNU-25-30-P-A DSNU-25-35-P-A DSNU-25-40-P-A DSNU-25-50-P-A DSNU-25-60-P-A DSNU-25-70-P-A DSNU-25-80-P-A DSNU-25-100-P-A DSNU-25-125-P-A DSNU-25-150-P-A DSNU-25-160-P-A DSNU-25-200-P-A DSNU-25-250-P-A DSNU-25-300-P-A DSNU-25-320-P-A DSNU-25-400-P-A DSNU-25-500-P-A
PPV Pneumatic cushioning, adjustable at both ends A With position sensing Part No. Type 1908289 1908290 1908291 33974 1908292 1908293 19236 19237 1908294 1908295 19238 19239 19240 1908296 19241 19242 19243 19244 34720 1908312 1908313 1908314 33975 1908315 1908316 19245 19246 1908317 1908318 19247 19248 19249 1908319 19250 19251 19252 19253 34721 35193 35194 DSNU-20-10-PPV-A DSNU-20-15-PPV-A DSNU-20-20-PPV-A DSNU-20-25-PPV-A DSNU-20-30-PPV-A DSNU-20-35-PPV-A DSNU-20-40-PPV-A DSNU-20-50-PPV-A DSNU-20-60-PPV-A DSNU-20-70-PPV-A DSNU-20-80-PPV-A DSNU-20-100-PPV-A DSNU-20-125-PPV-A DSNU-20-150-PPV-A DSNU-20-160-PPV-A DSNU-20-200-PPV-A DSNU-20-250-PPV-A DSNU-20-300-PPV-A DSNU-20-320-PPV-A DSNU-25-10-PPV-A DSNU-25-15-PPV-A DSNU-25-20-PPV-A DSNU-25-25-PPV-A DSNU-25-30-PPV-A DSNU-25-35-PPV-A DSNU-25-40-PPV-A DSNU-25-50-PPV-A DSNU-25-60-PPV-A DSNU-25-70-PPV-A DSNU-25-80-PPV-A DSNU-25-100-PPV-A DSNU-25-125-PPV-A DSNU-25-150-PPV-A DSNU-25-160-PPV-A DSNU-25-200-PPV-A DSNU-25-250-PPV-A DSNU-25-300-PPV-A DSNU-25-320-PPV-A DSNU-25-400-PPV-A DSNU-25-500-PPV-A
25
20
Internet: www.festo.com/catalog/...
Stroke [mm] 40 50 80 100 125 160 200 40 50 80 100 125 160 200 250 300 320 40 50 80 100 125 160 200 250 300 320 400 500
PPS Pneumatic cushioning, self-adjustable at both ends Without position sensing Part No. Type 559234 559235 559236 559237 559238 559239 559240 559241 559242 559243 559244 559245 559246 559247 559248 559249 559250 559251 559252 559253 559254 559255 559256 559257 559258 559259 559260 559261 559262 DSNU-16-40-PPS DSNU-16-50-PPS DSNU-16-80-PPS DSNU-16-100-PPS DSNU-16-125-PPS DSNU-16-160-PPS DSNU-16-200-PPS DSNU-20-40-PPS DSNU-20-50-PPS DSNU-20-80-PPS DSNU-20-100-PPS DSNU-20-125-PPS DSNU-20-160-PPS DSNU-20-200-PPS DSNU-20-250-PPS DSNU-20-300-PPS DSNU-20-320-PPS DSNU-25-40-PPS DSNU-25-50-PPS DSNU-25-80-PPS DSNU-25-100-PPS DSNU-25-125-PPS DSNU-25-160-PPS DSNU-25-200-PPS DSNU-25-250-PPS DSNU-25-300-PPS DSNU-25-320-PPS DSNU-25-400-PPS DSNU-25-500-PPS
20
25
Internet: www.festo.com/catalog/...
21
Stroke [mm] 10 15 20 25 30 35 40 50 60 70 80 100 125 150 160 200 10 15 20 25 30 35 40 50 60 70 80 100 125 150 160 200 250 300 320
PPS Pneumatic cushioning, self-adjustable at both ends A With position sensing Part No. Type 1908274 1908275 1908276 559263 1908277 1908278 559264 559265 1908279 1908280 559266 559267 559268 1908281 559269 559270 1908297 1908298 1908299 559271 1908300 1908301 559272 559273 1908302 1908303 559274 559275 559276 1908304 559277 559278 559279 559280 559281 DSNU-16-10-PPS-A DSNU-16-15-PPS-A DSNU-16-20-PPS-A DSNU-16-25-PPS-A DSNU-16-30-PPS-A DSNU-16-35-PPS-A DSNU-16-40-PPS-A DSNU-16-50-PPS-A DSNU-16-60-PPS-A DSNU-16-70-PPS-A DSNU-16-80-PPS-A DSNU-16-100-PPS-A DSNU-16-125-PPS-A DSNU-16-150-PPS-A DSNU-16-160-PPS-A DSNU-16-200-PPS-A DSNU-20-10-PPS-A DSNU-20-15-PPS-A DSNU-20-20-PPS-A DSNU-20-25-PPS-A DSNU-20-30-PPS-A DSNU-20-35-PPS-A DSNU-20-40-PPS-A DSNU-20-50-PPS-A DSNU-20-60-PPS-A DSNU-20-70-PPS-A DSNU-20-80-PPS-A DSNU-20-100-PPS-A DSNU-20-125-PPS-A DSNU-20-150-PPS-A DSNU-20-160-PPS-A DSNU-20-200-PPS-A DSNU-20-250-PPS-A DSNU-20-300-PPS-A DSNU-20-320-PPS-A
20
22
Internet: www.festo.com/catalog/...
Stroke [mm] 10 15 20 25 30 35 40 50 60 70 80 100 125 150 160 200 250 300 320 400 500
PPS Pneumatic cushioning, self-adjustable at both ends A With position sensing Part No. Type 1908320 1908321 1908322 559282 1908323 1908324 559283 559284 1908325 1908326 559285 559286 559287 1908327 559288 559289 559290 559291 559292 559293 559294 DSNU-25-10-PPS-A DSNU-25-15-PPS-A DSNU-25-20-PPS-A DSNU-25-25-PPS-A DSNU-25-30-PPS-A DSNU-25-35-PPS-A DSNU-25-40-PPS-A DSNU-25-50-PPS-A DSNU-25-60-PPS-A DSNU-25-70-PPS-A DSNU-25-80-PPS-A DSNU-25-100-PPS-A DSNU-25-125-PPS-A DSNU-25-150-PPS-A DSNU-25-160-PPS-A DSNU-25-200-PPS-A DSNU-25-250-PPS-A DSNU-25-300-PPS-A DSNU-25-320-PPS-A DSNU-25-400-PPS-A DSNU-25-500-PPS-A
Stroke [mm]
P Flexible cushioning rings/pads at both ends A With position sensing Part No. Type 14326 14325 14324 14323 14328 14327 DSNU-8--P-A DSNU-10--P-A DSNU-12--P-A DSNU-16--P-A DSNU-20--P-A DSNU-25--P-A
PPV Pneumatic cushioning, adjustable at both ends A With position sensing Part No. Type
-H-
Note
Additional variants can be configured and ordered via the DSNU product modules 35.
Internet: www.festo.com/catalog/...
23
-V- New
-N-T-
16
20
25 Gx
Mode of operation Cushioning Position sensing Type of mounting Mounting position Operating and environmental conditions Operating medium Note on operating/pilot medium Operating pressure1) Ambient temperature Corrosion resistance class CRC2)
1) 2)
M5 Gx Piston Piston rod Cylinder barrel Double-acting Flexible cushioning rings/pads at both ends Via proximity sensor Via accessories Any
[bar] [C]
Compressed air in accordance with ISO 8573-1:2010 [7:4:4] Operation with lubricated medium possible (in which case lubricated operation will always be required) 18 10 +60 2
Note operating range of proximity sensors Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents.
Force [N] and impact energy [J] Piston Theoretical force at 6 bar, advancing Theoretical force at 6 bar, retracting Impact energy at end positions Weight [g] Piston Product weight with 0 mm stroke Additional weight per 10 mm stroke Moving load at 0 mm stroke Additional load per 10 mm stroke
16 47 4 23 2
20 83 6 44 4
25 111 8 71 6
24
Internet: www.festo.com/catalog/...
-V- New
16 0.015 2.3
20 0.02 2.3
25 0.015 2.3
0.015 1.9
0.02 1.7
0.015 2.0
Standard cylinder 1 2 3 4 Piston rod Bearing cap Cylinder barrel End cap Seals Note on materials High-alloy stainless steel Polyamide Wrought aluminium alloy Polyamide Polyurethane, nitrile rubber RoHS-compliant
16 20 25
Internet: www.festo.com/catalog/...
25
-V- New
-H-
Note
For the compressed air ports only push-in fittings or one-way flow control valves with cylindrical connecting thread (M or G thread) may be used. Piston rod nut is not included in scope of delivery for 16/20. [mm] 16 20 25 [mm] 16 20 25 [mm] 16 20 25
1)
AM
B h9 16 22 22 G
BE
BF
CD H9 6 8 8 L2 MM 6 8 10
D 20 27 27 OH
D4 18 22 27 PL
EE
16 20 22 EW
17 20 22
M5 Gx Gx VD
12 16 16 WF
10 16 16 XC 1 82 95 104
M6 M8 M10x1.25 ZJ
8 12 12 1
56 68 70 2
14 19 19
2 2 2
Max. tightening torque of thread [Nm] BE1) EE 12/8 22/15 22/15 1.3 6 6
22 24 28
Bearing cap/end cap
78 92 98
5 7 9
19 27 27
-H-
Note
Part No. 551 668 551 669 551 670 551 671 551 672 551 673 551 674 551 675 551 676
Type DSNUP-16-25-P-A DSNUP-16-50-P-A DSNUP-16-100-P-A DSNUP-20-25-P-A DSNUP-20-50-P-A DSNUP-20-100-P-A DSNUP-25-25-P-A DSNUP-25-50-P-A DSNUP-25-100-P-A
20
25
26
Internet: www.festo.com/catalog/...
-N-T-
General technical data Piston Pneumatic connection Piston rod thread Operating medium Constructional design Max. torque at the piston rod Cushioning [Nm]
12
16
20 Gx M8
25 Gx M10x1.25
[mm]
M5 M5 M6 M6 Compressed air, filtered, lubricated or unlubricated Piston Protected against rotation with square piston rod 0.10 0.10 Flexible cushioning rings/ pads at both ends Adjustable cushioning at both ends 12 Via proximity sensor Via accessories Any
0.20
0.45
15
17
-H- Note: This product conforms to ISO 1179-1 and to ISO 228-1
Operating conditions Piston Operating medium Note on operating/pilot medium Operating pressure [bar]
1)
12
16
20
25
Compressed air in accordance with ISO 8573-1:2010 [7:4:4] Operation with lubricated medium possible (in which case lubricated operation will always be required) 1.5 101) 1 10
With DSNU-12- -Q- PPV (pneumatic cushioning adjustable at both ends): 2 10 bar
Ambient conditions Standard cylinder Ambient temperature1) [C] Corrosion resistance class CRC2)
1) 2)
R3 3
Note operating range of proximity sensors. Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents. Corrosion resistance class 3 as per Festo standard 940 070 Components requiring higher corrosion resistance. External visible parts in direct contact with industrial atmospheres or media such as solvents and cleaning agents, with a predominantly functional requirement for the surface.
Internet: www.festo.com/catalog/...
27
12
Theoretical force at 6 bar, advancing 68 Theoretical force at 6 bar, retracting 51 Max. impact energy at the end positions 0.07 for flexible cushioning elements1)
1) The values are reduced by approx. 50% at an ambient temperature of 80 C
Weight [g] Piston Product weight with 0 mm stroke Additional weight per 10 mm stroke Materials Sectional view 1 2
12 80 4.1
16 110 4.7
20 215 7.1
25 275 10.9
Standard cylinder 1 2 3 4 Piston rod Bearing cap Cylinder barrel End cap Seals High-alloy stainless steel Anodised aluminium High-alloy stainless steel Anodised aluminium Polyurethane, nitrile rubber
28
Internet: www.festo.com/catalog/...
-H+ [mm] 12 16 20 25 [mm] 12 16 20 25 10 16 M6 M8 M10x1.25 24 32 8 11 9 12 50 56 68 69.5 6 2 8.2 22 24 28 16 20 22 G AM B h9 16 22 B1 j BE BF CD H9 6 8 D D4 13.3 17.3 21.3 26.5 VD WF
Note
Piston rod nut is not included in scope of delivery for 12 20. = plus stroke length EE EW
5.5 7 9 KV
M16x1.5 M22x1.5
17 20 22 L
20 27
M5 Gx
12 16
KK
KW
L2
PL
XC 1 75 82 95 104
ZJ
72 78 92 97.5
-H- Note: This product conforms to ISO 1179-1 and to ISO 228-1
Internet: www.festo.com/catalog/...
29
-H-
Note
-N-T-
Additional measures are required for use in safety-related applications; in Europe, for example, the standards listed under the EC Machinery Directive must be observed. Without additional measures in accordance with statutory minimum requirements, the product is not suitable for use in safety-related sections of control systems.
General technical data Piston Pneumatic connection Piston rod thread Constructional design
10
12
16
20
25 Gx M10x1.25
Cushioning
[mm] [mm]
Mounting position Holding force of the clamping [N] unit Axial play under load [mm] Pneumatic connection of the clamping unit
M5 M5 M5 M5 Gx M4 M4 M6 M6 M8 Piston Piston rod Cylinder barrel Flexible cushioning rings/pads at both ends Pneumatic cushioning, adjustable at both ends Self-adjusting cushioning at both ends 9 12 15 12 15 Via proximity sensor Via through-holes Via accessories Any 80 80 180 180 350 0.2 M5 0.3
17 17
350 0.5
-H- Note: This product conforms to ISO 1179-1 and to ISO 228-1
Operating conditions Piston Operating medium Note on operating/pilot medium Operating pressure [bar] Ambient conditions Standard cylinder Ambient temperature1) [C] Corrosion resistance class CRC2)
1) 2)
10
12
16
20
25
Compressed air in accordance with ISO 8573-1:2010 [7:4:4] Operation with lubricated medium possible (in which case lubricated operation will always be required) 3 10
R3 3
Note operating range of proximity sensors. Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents. Corrosion resistance class 3 as per Festo standard 940 070 Components requiring higher corrosion resistance. External visible parts in direct contact with industrial atmospheres or media such as solvents and cleaning agents, with a predominantly functional requirement for the surface.
30
Internet: www.festo.com/catalog/...
10 47 40 0.05
12 68 51 0.07
Theoretical force at 6 bar, advancing 30 Theoretical force at 6 bar, retracting 23 Max. impact energy at the end positions 0.03 for flexible cushioning elements1)
1) The values are reduced by approx. 50% at an ambient temperature of 80 C
Average piston speed v as a function of applied load m in combination with cushioning PPS Piston 16 Piston 20
-H-
Note
-H-
Note Additional graphs for PPS cushioning www.festo.com Design software for PPV cushioning ProDrive
Design software for flexible cushioning elements ProDrive Weight [g] Piston Product weight with 0 mm stroke Additional weight per 10 mm stroke
8 97.6 2.4
10 100.3 2.7
12 193 4
16 207.9 4.6
20 393.8 7.2
25 456 11
Internet: www.festo.com/catalog/...
31
Basic version
8/10 12/16 20 25
2 3
Standard cylinder 1 2 3 4 5 6 Piston rod Bearing cap Housing, clamping unit Clamping jaws Cylinder barrel End cap Piston, clamping unit Spring Seals High-alloy stainless steel Anodised aluminium Wrought aluminium alloy Brass High-alloy stainless steel Anodised aluminium Polyacetate Spring steel Polyurethane, nitrile rubber
32
Internet: www.festo.com/catalog/...
20/25
8 ... 16
Note
Piston rod nut is not included in scope of delivery for 8 20. = plus stroke length
-H-
Note bination with variant Q, the righthand piston rod is square, the lefthand piston rod round. The clamping unit is mounted on the left-hand, round piston rod. + = plus stroke length ++ = plus 2x stroke length
The thread types at both piston rod ends are identical. The clamping unit is mounted on only one side. In com-
Internet: www.festo.com/catalog/...
33
19.5 24 27
27 32 36
12 17 20 22 H2
15 20 27
12 16 20 4.2 M5
EE
EW
H1
KK
KV
MM
L2
L6
L7
L8
L9
T3
PL
WF
ZM
5 7 9
-H- Note: This product conforms to ISO 1179-1 and to ISO 228-1
34
Internet: www.festo.com/catalog/...
193 986 193 987 193 988 193 989 193 990 193 991 Order example 193 991 Ordering table Size 0 M Module No. Function Piston Stroke Cushioning
DSNU
8 10 12 16 20 25
1 500
P PPV PPS
MQ MA MH
S2
DSNU
25
350
PPV
MH
S2
8 193 986
10 193 987
12 193 988
16 193 989
20 193 990
25 193 991
Conditions
Code
Enter code
Standard cylinder, double-acting, based on ISO 6432 [mm] 8 10 12 16 20 25 [mm] 1 100 1 200 1 320 1 500 Flexible cushioning rings/pads at both ends Pneumatic cushioning, adjustable at both ends 1 Pneumatic cushioning, aC self-adjusting at both ends Via proximity sensor Lateral supply port, end cap Axial supply port, end cap With mounting flange at front (direct mounting), bearing cap Through piston rod
4 MH 5 S2 aC PPS Not with combination S6-R3. Not with KP, S10, S11 Not with S10, S11 Not with MA, MH, S6, S10, S11 and not with combination MQ-R3
DSNU
2 3 3 4 5
In combination with S6, S10, S11 not with piston 12 mm Minimum stroke: 10 mm Not with S2, S10, S11
-H-
Note
The bellows kit DADB must not be used in combination with the variant MH. The running characteristics change slightly when the bellows kit DADB is combined with the variant S10 or S11. Transfer order code DSNU
Internet: www.festo.com/catalog/...
35
K2
K3
K5
K8
KP
S6
S11
R3
7K6
M10K5
R3
10
12
16
20
25
Conditions 6 7 8
Code
Enter code
Extended male thread 0 O Shortened male thread Female thread Special thread Piston rod extended at one end Clamping unit Temperature resistance Slow speed (constant motion) Low friction Corrosion protection
6 K2 7 K6 8 K3 9 KP Not with K3, K6 Not with K3 Not with K5 Not with S6, S10, S11, R3
Extended male piston rod thread [mm] 1 15 1 20 1 25 1 35 Shortened male piston rod thread [mm] 1 4 18 1 10 Female piston rod thread (M4) (M6) Piston rod with special thread M10 Extended piston rod at one end [mm] 1 50 1 100 1 110 1 150 Attached Heat-resistant seals for temperatures up to 120 C Slow speed (constant motion at low piston speeds) Low friction High corrosion protection
aJ S6 aA S10 aB S11 Not with S10, S11 Not with S11, R3 Not with R3
9 aJ aA aB
36
Internet: www.festo.com/catalog/...
193 988 193 989 193 990 193 991 Order example 193 990 Ordering table Size 0 M Module No. Function Piston Stroke Cushioning
DSNU
12 16 20 25
1 500
P PPV
MQ MA MH
S2
DSNU
20
150
PPV
MQ
12 193 988
16 193 989
20 193 990
25 193 991
Conditions
Code
Enter code
Standard cylinder, double-acting, based on ISO 6432 [mm] 12 16 20 25 [mm] 5 160 5 200 5 250 Flexible cushioning rings/pads at both ends Pneumatic cushioning, adjustable at both ends Via proximity sensor Lateral supply port, end cap Axial supply port, end cap With mounting flange at front (direct mounting), bearing cap Square piston rod Through piston rod
3 MH Not with combination Q-R3
DSNU - - -P
DSNU
-H-
Note
The bellows kit DADB must not be used in combination with the variant Q. Transfer order code DSNU
Internet: www.festo.com/catalog/...
37
K2
K6
K3
K5
K8
KP
R3
60K8
KP
12
16
20
25
Conditions 4 5 6
Code
Enter code
Extended male thread 0 O Shortened male thread Female thread Special thread Piston rod extended at one end Clamping unit Corrosion protection
4 K2 5 K6 6 K3 Not with K3, K6 Not with K3 Not with K5
Extended male piston rod thread [mm] 1 20 1 25 Shortened male piston rod thread [mm] 1 4 18 Female piston rod thread (M4) Piston rod with special thread Extended piston rod at one end [mm] 1 100 1 110 Attached High corrosion protection
7 KP Only with S2. Not with R3
38
Internet: www.festo.com/catalog/...
-N-T-
Basic version
Axial air connection MA General technical data Piston Pneumatic connection Piston rod thread Constructional design
10
12
16 M5 M6
20 Gx M8
25 Gx M10x1.25
M5 M5 M5 M4 M4 M6 Piston Piston rod Cylinder barrel Flexible cushioning rings/pads at both ends Via proximity sensor Via accessories Any
-H- Note: This product conforms to ISO 1179-1 and to ISO 228-1
Operating conditions Piston Operating medium Note on operating/pilot medium Operating pressure [bar] Ambient conditions Standard cylinder Ambient temperature1) [C] Corrosion resistance class CRC2)
1) 2)
10
12
16
20
25
Compressed air in accordance with ISO 8573-1:2010 [7:4:4] Operation with lubricated medium possible (in which case lubricated operation will always be required) 1.5 10 1.2 10
20 +80 2
Note operating range of proximity sensors. Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents.
Internet: www.festo.com/catalog/...
39
Weight ESNU-... [g] Piston Product weight with 0 mm stroke Additional weight per 10 mm stroke Weight ESNU-...-MA [g] Piston Product weight with 0 mm stroke Additional weight per 10 mm stroke Materials Sectional view 1 2
8 35 2.4
10 37.3 2.7
12 75 4
16 89.9 4.6
20 186.8 7.2
25 238 11
8 30 2.4
10 33 2.7
12 65 4
16 81 4.6
20 167 7.2
25 222 11
Standard cylinder 1 2 3 4 Piston rod Bearing cap Cylinder barrel End cap Seals Spring High-alloy stainless steel Anodised aluminium High-alloy stainless steel Anodised aluminium Polyurethane, nitrile rubber Spring steel
40
Internet: www.festo.com/catalog/...
Note
Piston rod nut is not included in scope of delivery for 8 20. = plus stroke length
+ [mm] 8 10 12 16 20 25 [mm] 8 10 12 16 20 25 6 8 11 6 9 12 46 50 56 68 69.5 12 16 20 22 KW AM B h9 12 16 22 BE BF CD H9 4 6 8 D D2 10.5 12.5 14.5 17.5 21.7 26.7 PL D4 9.3 11.3 13.3 17.3 21.3 26.5 VD EE EW
15 20 27
8 M5 12 Gx 16 16 10
M4 M6 M8 M10x1.25 ZJ -MA
19 24 32
L3
MM
WF
XC 1
4 6 6 8 10 8.2 2
16 22 24 28
64 75 82 95 104
62 72 78 92 97.5
5 7 9
-H- Note: This product conforms to ISO 1179-1 and to ISO 228-1
Internet: www.festo.com/catalog/...
41
[mm] 8 10 12 16 20 25
1)
A1 max.
A2 max.
A3 max.
AF
AM
KF Basic thread
T4
WF
15 4 20 25 35 50 8
12
12 16 20 22
M4 M6
M4 M6 M8 M10x1.25
2 2.6
16 22 24 28
The special threads are only available as male threads. The scope of delivery does not include a hex nut for the piston rod thread.
42
Internet: www.festo.com/catalog/...
Stroke [mm]
Part No.
Type
[mm]
Stroke [mm]
Part No.
Type
Internet: www.festo.com/catalog/...
43
Function ESNU
ESNU
25
45
MA
8 193 996
10 193 997
12 193 998
16 193 999
20 194 000
25 194 001
Conditions
Code
Enter code
Standard cylinder, single-acting pushing, based on ISO 6432 [mm] 8 10 12 16 20 25 [mm] 1 50 Flexible cushioning rings/pads at both ends Via proximity sensor Axial air connection 1
ESNU - - -P -A -MA
ESNU
-P
44
Internet: www.festo.com/catalog/...
30K2 Ordering table Size Extended male thread 0 O Shortened male thread Female thread Special thread Extended piston rod
M10K5
30K8
10
12
16
20
25
Conditions 2
Code
Enter code
Extended male piston rod thread [mm] 1 15 1 20 Shortened male piston rod thread [mm] 1 4 Female piston rod thread Piston rod with special thread Extended piston rod [mm] 1 50
1 25 18 (M4)
1 35
-K2 -K6
(M6) M10
-K3 -K5 K8
2 3
K2 K3
Not with female thread K3, shortened male thread K6 Not with special thread K5, shortened male thread K6
Internet: www.festo.com/catalog/...
45
-N-T-
General technical data Piston Pneumatic connection Piston rod thread Constructional design
10
12
16 M5 M6
20 Gx M8
25 Gx M10x1.25
M5 M5 M5 M4 M4 M6 Piston Piston rod Cylinder barrel Flexible cushioning rings/pads at both ends Via accessories Any
-H- Note: This product conforms to ISO 1179-1 and to ISO 228-1
Operating conditions Piston Operating medium Note on operating/pilot medium Operating pressure [bar] Ambient conditions Standard cylinder Ambient temperature [C] Corrosion resistance class CRC1)
1)
10
12
16
20
25
Compressed air in accordance with ISO 8573-1:2010 [7:4:4] Operation with lubricated medium possible (in which case lubricated operation will always be required) 1.5 10 1 10
20 +80 2
Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents.
46
Internet: www.festo.com/catalog/...
8 30 23
10 47 40
12 68 51
16 121 104
20 189 158
25 295 247
The force in the advance stroke is the same as the force in the return stroke with the variant S2
Weights [g] Piston Product weight with 0 mm stroke Additional weight per 10 mm stroke Materials Sectional view 1 2
8 40 2.3
10 43 2.5
12 80 4.1
16 96 4.7
20 200 7.1
25 260 10.9
Standard cylinder 1 2 3 4 Piston rod Bearing cap Cylinder barrel End cap Seals High-alloy stainless steel Anodised aluminium High-alloy stainless steel Anodised aluminium Polyurethane, nitrile rubber
Internet: www.festo.com/catalog/...
47
Note
Piston rod nut is not included in scope of delivery for 8 20. = plus stroke length
+ = plus stroke length ++ = plus 2x stroke length [mm] 8 10 12 16 20 25 [mm] 8 10 12 16 20 25 19 24 32 6 8 11 6 9 12 46 50 56 68 69.5 4 6 6 8 10 8.2 2 22 24 28 16 12 16 20 22 KV AM B h9 12 16 22 BE BF CD H9 4 6 8 D D4 9.3 11.3 13.3 17.3 21.3 26.5 VD EE EW G KK
12 17 20 22 L2
15 20 27
8 M5 12 Gx 16 16 10
M4 M6 M8 M10x1.25 ZM 1
KW
MM
PL
WF
XC 1 64 75 82 95 104
ZJ
62 72 78 92 97.5
5 7 9
-H- Note: This product conforms to ISO 1179-1 and to ISO 228-1
48
Internet: www.festo.com/catalog/...
Piston [mm]
Stroke [mm]
10
12
Internet: www.festo.com/catalog/...
49
Piston [mm]
Stroke [mm]
20
25
50
Internet: www.festo.com/catalog/...
Piston [mm]
Stroke [mm]
10 320 10 500
11 893 11 894
DSN-20--PPV-S2 DSN-25--PPV-S2
Internet: www.festo.com/catalog/...
51
-N-T-
General technical data Piston Pneumatic connection Piston rod thread Constructional design
10
12
16 M5 M6
20 Gx M8
25 Gx M10x1.25
M5 M5 M5 M4 M4 M6 Piston Piston rod Cylinder barrel Flexible cushioning rings/pads at both ends Via accessories Any
-H- Note: This product conforms to ISO 1179-1 and to ISO 228-1
Operating conditions Piston Operating medium Note on operating/pilot medium Operating pressure [bar] Ambient conditions Standard cylinder Ambient temperature [C] Corrosion resistance class CRC1)
1)
10
12
16
20
25
Compressed air in accordance with ISO 8573-1:2010 [7:4:4] Operation with lubricated medium possible (in which case lubricated operation will always be required) 1.5 10 1.2 10
20 +80 2
Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents.
52
Internet: www.festo.com/catalog/...
8 40 2.3
10 43 2.5
12 80 4.1
16 96 4.7
20 200 7.1
25 260 10.9
Standard cylinder 1 2 3 4 Piston rod Bearing cap Cylinder barrel End cap Seals Spring High-alloy stainless steel Anodised aluminium High-alloy stainless steel Anodised aluminium Polyurethane, nitrile rubber Spring steel
Internet: www.festo.com/catalog/...
53
-H+ [mm] 8 10 12 16 20 25 [mm] 8 10 12 16 20 25 19 24 32 6 8 11 6 9 12 46 50 56 68 69.5 4 6 6 8 10 8.2 2 22 24 28 16 12 16 20 22 KV AM B h9 12 16 22 BE BF CD H9 4 6 8 D D4 9.3 11.3 13.3 17.3 21.3 26.5 VD EE EW
Note
Piston rod nut is not included in scope of delivery for 8 20. = plus stroke length G KK
12 17 20 22 L2
15 20 27
8 M5 12 Gx 16 16 10
M4 M6 M8 M10x1.25 1
KW
MM
PL
WF
XC 1 64 75 82 95 104
ZJ
62 72 78 92 97.5
5 7 9
-H- Note: This product conforms to ISO 1179-1 and to ISO 228-1
54
Internet: www.festo.com/catalog/...
Stroke [mm]
Part No.
Type
[mm]
Stroke [mm]
Part No.
Type
Internet: www.festo.com/catalog/...
55
HBN/CRHBN-x2
AO
AT
AU
R1
SA -KP
TR
US
XA -KP
XS -KP 24 32 32 36 40
5 6 6 8 8
3 4 4 5 5
11 14 14 17 17
10 13 13 20 20
68 78 84 102 103.5
25 32 32 40 40
35 42 42 54 54
73 86 92 109 114.5
Part No. 161 866 162 999 161 867 162 998
Type
1)
Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents. Corrosion resistance class 4 as per Festo standard 940 070 Components requiring higher corrosion resistance. Parts used with aggressive media, e.g. food or chemical industry. These applications should be supported with special tests with the media if required.
56
Internet: www.festo.com/catalog/...
+ Dimensions and ordering data For AB [mm] 8, 10 12 16 20 25 For [mm] 8, 10 12, 16 20, 25
1)
AT
TF
UF
UR
ZF -KP
4.5 5.5 5.5 6.6 6.6 Basic version CRC1) Weight [g] 2 2 2 12 26 52
3 4 4 5 5
30 40 40 50 50
40 53 53 66 66
13 18 18 19 23
65 76 82 97 102.5
Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents. Corrosion resistance class 4 as per Festo standard 940 070 Components requiring higher corrosion resistance. Parts used with aggressive media, e.g. food or chemical industry. These applications should be supported with special tests with the media if required.
Swivel mounting SBN Material: Mounting ring: Wrought aluminium alloy, anodised Bearing: Bronze Screws: Galvanised steel Bracket: Steel Cannot be used on the bearing cap in combination with bellows kit DADB. Dimensions and ordering data For CM FL [mm] 20/25
1)
GL
HB
L1 max.
LE
MR
RF
RG
UK
UX
CRC1)
Weight [g]
Part No.
Type
38.1+0.4
35
20
60.2
31
12
20
24
46.1
40
200
539 927
SBN-20/25
Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a surrounding industrial atmosphere or media such as cooling or lubricating agents.
Internet: www.festo.com/catalog/...
57
TM
UM
UW
XH
XL -KP
CRC1)
Weight [g]
Part No.
Type
4 6 6 6 6
6 8 8 8 8
26 38 38 46 46
38 58 58 66 66
20 25 25 30 30
13 18 18 20 24
65 76 82 96 101.5
2 2 2 2 2
20 50 50 70 70
Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a surrounding industrial atmosphere or media such as cooling or lubricating agents.
Clevis foot LBN/CRLBN Material: LBN: Galvanised steel CRLBN: High-alloy stainless steel Free of copper and PTFE RoHS-compliant
Dimensions and ordering data For CM [mm] 8, 10 12, 16 20, 25 For [mm] 8, 10 12, 16 20, 25
1)
EK 4 6 8
FL
GL
HB
LE
MR
RG
UX
13.8 13 16
21.5 24 26
5 7 10
12.5 15 20
20 25 32
Corrosion resistance class 2 as per Festo standard 940 070 Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or lubricating agents. Corrosion resistance class 4 as per Festo standard 940 070 Components requiring higher corrosion resistance. Parts used with aggressive media, e.g. food or chemical industry. These applications should be supported with special tests with the media if required.
58
Internet: www.festo.com/catalog/...
Type
For 8 10 12 16 20 25
32 963
16 20, 25
MSK-M16X1,5 MSK-M22X1,5
Ordering data Piston rod attachments, corrosion resistant Designation For Part No. Type Rod eye CRSGS 12 16 20 25 Ordering data Guide units For 8, 10 12, 16 20 25 195 580 195 581 195 582 CRSGS-M6 CRSGS-M8 CRSGS-M10x1,25
For 12 16 20 25
With recirculating ball bearing guide Part No. Type 35 197 33 481 33 482 33 483 FEN-8/10--KF FEN-12/16--KF FEN-20--KF FEN-25--KF
Technical data Internet: feng With plain-bearing guide Part No. Type 35 196 19 168 19 169 19 170 FEN-8/10- FEN-12/16- FEN-20- FEN-25-
Internet: www.festo.com/catalog/...
59
General technical data Type DADB-S1Max. stroke range of cylinder1) Type of mounting Mounting position Resistance to media Ambient temperature3) Corrosion resistance class CRC4)
1) 2) 3) 4)
16
20
25 10 500 10 50
[C]
10 200 10 200 10 320 10 50 With threaded pin Any Dust, chippings, oil, grease, fuel ( Internet: Resistance to media) 10 +80 3
In combination with the bellows kit DADB Slight change in spring return force Note operating range of proximity sensors and cylinder Corrosion resistance class 3 as per Festo standard 940 070 Components with heavy corrosion exposure. Externally visible components in direct contact with normal industrial atmosphere or media such as solvents and cleaning agents, where the surface requirement is predominantly functional.
Materials Sectional view 1 2 3 4 Bellows 1 2 3 4 Connection Intermediate piece Bellows End piece O-ring Note on materials Polyamide Polyamide Nitrile rubber Polyamide Nitrile rubber Free of copper and PTFE RoHS compliant
Weight [g] Type DADB-S1Stroke [mm] 10 50 51 100 101 150 151 200 201 250 251 300 301 350 351 400 401 450 451 500
12 7 9 13 16
16 7 9 13 16
20 20 32 45 58 73 85 100
60
Internet: www.festo.com/catalog/...
Advancing
Retracting
12/16 20/25
-H-
Note
The push-in fittings opposite must be used for the pressure compensation hole. Silencers can be used as an alternative. This reduces the travel speed slightly.
Tubing length and push-in fitting for pressure compensation hole Tubing O.D. Push-in fitting [mm] [mm] Part No. Type 12, 16, 20, 25 6 153 317 537 014 533 845 533 875 QSM-M5-6-I QS-F-M5-6-I QS-F-M5-6H QS-F-M5-6
Internet: www.festo.com/catalog/...
61
+ Stroke [mm] 10 50 51 100 101 150 151 200 201 250 251 300 301 350 351 400 401 450 451 500 Stroke [mm] 10 50 51 100 101 150 151 200 201 250 251 300 301 350 351 400 401 450 451 500
1)
A21) 23 34 48 59
D1 max.
D2
12/16 EE
L1
L2
WF+A2 45 56 70 81 25 EE
A21) 22 34 47 60 75 86 101
D1 max.
D2
20 EE
L1
L2
22
8.5
M5
3.2
29
8.5
M5
4.2
2.7
D1 max.
D2
L1
L2
29
8.5
M5
4.2
2.7
The dimension corresponds to the K8 value (extended piston rod) of the drive
62
Internet: www.festo.com/catalog/...
Cylinder data Stroke [mm] 12 [mm] 10 50 51 100 101 150 151 200 10 50 51 100 101 150 151 200 201 250 251 300 301 320
Bellows kit Dimension Part No. Type for K8 [mm] 23 34 48 59 22 34 47 60 75 86 101 553 391 553 393 553 395 553 397 553 407 553 409 553 411 553 413 553 415 553 417 553 419 DADB-S1-12-S10-50 DADB-S1-12-S51-100 DADB-S1-12-S101-150 DADB-S1-12-S151-200 DADB-S1-20-S10-50 DADB-S1-20-S51-100 DADB-S1-20-S101-150 DADB-S1-20-S151-200 DADB-S1-20-S201-250 DADB-S1-20-S251-300 DADB-S1-20-S301-350
20
25
-H-
Note
Can only be used with piston 20 and 25 of the single-acting standard cylinder ESNU.
Internet: www.festo.com/catalog/...
63
Ordering data Proximity sensors, round design, magnetic reed Assembly Electrical connection Cable Plug M8 N/O contact Via accessories 3-wire 3-pin
Ordering data Proximity sensors, round design, magnetic reed, corrosion resistant Assembly Electrical connection Cable length Cable Plug M8 [m] N/O contact Via accessories 3-wire 2.5
Part No.
161 775
CRSMEO-4-K-LED-24
Ordering data Mounting kits for proximity sensors SMEO/SMTO/CRSMEO Designation For Part No. Type Mounting kit SMBR 8 10 12 16 20 25 19 272 19 273 19 274 19 275 19 276 19 277 SMBR-8 SMBR-10 SMBR-12 SMBR-16 SMBR-20 SMBR-25
Technical data Internet: smbr Designation For Part No. Type Mounting kit CRSMBR, corrosion resistant 8 10 12 164 581 CRSMBR-12 16 164 582 CRSMBR-16 20 164 583 CRSMBR-20 25 164 584 CRSMBR-25
64
Internet: www.festo.com/catalog/...
Electrical connection
Part No.
NPN
N/C contact Insertable in the slot from above, flush with cylinder profile, short design PNP Cable, 3-wire 7.5 574340 SMT-8M-A-PO-24V-E-7,5-OE
Ordering data Proximity sensors for T-slot, magnetic reed Type of mounting Switching output N/O contact Insertable in the slot from above, flush with the cylinder profile Contacting
Electrical connection
Part No.
Cable, 3-wire Cable, 2-wire Plug M8x1, 3-pin Cable, 3-wire Plug M8x1, 3-pin
Insertable in the slot lengthwise, flush with the cylinder profile N/C contact Insertable in the slot lengthwise, flush with the cylinder profile
Contacting
543 862 543 863 543 872 543 861 150 855 150 857
Contacting
Cable, 3-wire
7.5
160 251
SME-8-O-K-LED-24
Ordering data Mounting kits for proximity sensors SME/SMT-8 Designation For Mounting kit SMBR-8 8 10 12 16 20 25
Part No. 175 091 175 092 175 093 175 094 175 095 175 096
Technical data Internet: smbr Type SMBR-8-8 SMBR-8-10 SMBR-8-12 SMBR-8-16 SMBR-8-20 SMBR-8-25
Internet: www.festo.com/catalog/...
65
Part No.
Ordering data Proximity sensors for C-slot, magnetic reed Type of mounting Switching Electrical connection, output connection direction N/O contact Insertable in the slot from above Insertable in slot lengthwise Contacting Plug M8x1, 3-pin, in-line Cable, 3-wire, in-line Cable, 2-wire, in-line Plug M8x1, 3-pin, in-line Cable, 3-wire, in-line
Part No.
Contacting
551 367 551 365 551 369 173 212 173 210
SME-10M-DS-24V-E-0,3-L-M8D SME-10M-DS-24V-E-2,5-L-OE SME-10M-ZS-24V-E-2,5-L-OE SME-10-SL-LED-24 SME-10-KL-LED-24 Technical data Internet: smbr Type SMBR-10-8 SMBR-10-10 SMBR-10-12 SMBR-10-16 SMBR-10-20 SMBR-10-25 Technical data Internet: nebu Type NEBU-M8G3-K-2.5-LE3 NEBU-M8G3-K-5-LE3 NEBU-M12G5-K-2.5-LE3 NEBU-M12G5-K-5-LE3 NEBU-M8W3-K-2.5-LE3 NEBU-M8W3-K-5-LE3 NEBU-M12W5-K-2.5-LE3 NEBU-M12W5-K-5-LE3
Ordering data Mounting kits for proximity sensors SME/SMT-10 Designation For Mounting kit SMBR-10 8 10 12 16 20 25 Ordering data Connecting cables Electrical connection, left Straight socket, M8x1, 3-pin Straight socket, M12x1, 5-pin Angled socket, M8x1, 3-pin Angled socket, M12x1, 5-pin
Part No. 175 101 173 227 175 102 173 228 175 103 175 104
Electrical connection, right Cable, open end, 3-wire Cable, open end, 3-wire Cable, open end, 3-wire Cable, open end, 3-wire
Part No. 541 333 541 334 541 363 541 364 541 338 541 341 541 367 541 370
66
Internet: www.festo.com/catalog/...
Gx
For supply air M5 3 4 6 3 4 6 8 Metal design 193 153 193 154 193 155 193 156 193 157 193 158 193 159 GRLZ-M5-QS-3-D GRLZ-M5-QS-4-D GRLZ-M5-QS-6-D GRLZ-x-QS-3-D GRLZ-x-QS-4-D GRLZ-x-QS-6-D GRLZ-x-QS-8-D Technical data Internet: crgrla Type
Gx
Ordering data One-way flow control valves, corrosion resistant Port Thread For push-in fitting For exhaust air M5 Gx CRQS/CRQSL/CRQST
Material
Part No.
CRGRLA-M5-B CRGRLA-x-B
-H-
Note
Only push-in fittings or one-way flow control valves with cylindrical connecting thread (M or G thread) may be used for the compressed air ports in conjunction with the DSNUP.
Internet: www.festo.com/catalog/...
67
Pneumatics Pneumatic linear and rotary actuators, valves, and air supply
PLCs and I/O Devices PLC's, operator interfaces, sensors and I/O devices
Supporting Advanced Automation As No One Else Can! Festo is a leading global manufacturer of pneumatic and electromechanical systems, components and controls for industrial automation, with more than 12,000 employees in 56 national headquarters serving more than 180 countries. For more than 80 years, Festo has continuously elevated the state of manufacturing with innovations and optimized motion control solutions that deliver higher performing, more profitable automated manufacturing and processing equipment. Our dedication to the advancement of automation extends beyond technology to the education and development of current and future automation and robotics designers with simulation tools, teaching programs, and on-site services.
Quality Assurance, ISO 9001 and ISO 14001 Certifications Festo Corporation is committed to supply all Festo products and services that will meet or exceed our customers requirements in product quality, delivery, customer service and satisfaction. To meet this commitment, we strive to ensure a consistent, integrated, and systematic approach to management that will meet or exceed the requirements of the ISO 9001 standard for Quality Management and the ISO 14001 standard for Environmental Management.
Copyright 2008, Festo Corporation. While every effort is made to ensure that all dimensions and specifications are correct, Festo cannot guarantee that publications are completely free of any error, in particular typing or printing errors. Accordingly, Festo cannot be held responsible for the same. For Liability and Warranty conditions, refer to our Terms and Conditions of Sale, available from your local Festo office. All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by any means, electronic, mechanical, photocopying or otherwise, without the prior written permission of Festo. All technical data subject to change according to technical update. Printed on recycled paper at New Horizon Graphic, Inc., FSC certified as an environmentally friendly printing plant.
United States
USA Headquarters, East: Festo Corp., 395 Moreland Road, Hauppauge, NY 11788 Phone: 1.631.435.0800; Fax: 1.631.435.8026; Email: info@festo-usa.com www.festo.com/us
Canada
USA Headquarters
Festo Corporation 395 Moreland Road P.O. Box 18023 Hauppauge, NY 11788, USA www.festo.com/us USA Sales Offices Appleton North 922 Tower View Drive, Suite N Greenville, WI 54942, USA Boston 120 Presidential Way, Suite 330 Woburn, MA 01801, USA Chicago 1441 East Business Center Drive Mt. Prospect, IL 60056, USA Dallas 1825 Lakeway Drive, Suite 600 Lewisville, TX 75057, USA Detroit Automotive Engineering Center 2601 Cambridge Court, Suite 320 Auburn Hills, MI 48326, USA New York 395 Moreland Road Hauppauge, NY 11788, USA Silicon Valley 4935 Southfront Road, Suite F Livermore, CA 94550, USA
Headquarters: Festo Inc., 5300 Explorer Drive, Mississauga, Ontario L4W 5G4 Phone: 1.905.624.9000; Fax: 1.905.624.9001; Email: festo.canada@ca.festo.com www.festo.ca
Mexico
Headquarters: Festo Pneumatic, S.A., Av. Ceyln 3, Col. Tequesquinahuac, 54020 Tlalnepantla, Edo. de Mxico Phone:011 52 [55] 53 21 66 00; Fax: 011 52 [55] 53 21 66 65; Email: festo.mexico@mx.festo.com www.festo.com/mx
Central USA
Festo Corporation 1441 East Business Center Drive Mt. Prospect, IL 60056, USA Phone:1.847.759.2600 Fax: 1.847.768.9480
Western USA
Festo Corporation 4935 Southfront Road, Suite F Livermore, CA 94550, USA Phone: 1.925.371.1099 Fax: 1.925.245.1286
Festo Worldwide
Argentina Estonia Lithuania Slovakia Australia Finland Slovenia Malaysia Austria Mexico South Africa Belarus Belgium Brazil Greece Spain Bulgaria Hong Kong Norway Sweden Canada Hungary Peru Chile India Philippines Taiwan China Indonesia Poland Thailand Colombia Iran Turkey Croatia Ireland Czech Republic Israel Russia Italy Japan Serbia Denmark Latvia Singapore Venezuela France Germany Great Britain
New Zealand
Romania
Switzerland
Ukraine
United States
www.festo.com