Professional Documents
Culture Documents
Page 1 of 7
Shear Terms
CENE 437: The Class: Loads: Lateral Loads: Seismic Loads: UBC '97: Base
In this section, the various terms of the static base shear equation are examined in more detail.
Effective peak ground accelerations with 10% probability of being exceeded in 50 yrs. Given as a percentage of acceleration due to gravity. horizontal ground acceleration is predicted at .4g at bedrock.
Doesn't account for building dynamic properties or local soil conditions. '97 UBC Figure 16.2 seismic zone map. Table 16.I Z values as given below: Zone Z 0 1 0
2A
.15
.075
Page 2 of 7
2B 3 4
.20
.30 .40
I = importance factor.
Classifying buildings according to use and importance. Essential facilities, hazardous facilities, special occupancy structures, standard occupancy structures, miscellaneous structures. remain functioning in a catastrophe.
Essential facilities mean that the building must Essential facilities include: hospitals, Design for greater safety.
Fundamental period of vibration is the length of time, in seconds, it takes a structure to move through one complete cycle of free vibration in the first mode.
Page 3 of 7
vibrations for masonry buildings is estimated at: Height (ft) Period (seconds) 20 40 120 160
a v
60
.73 .90
C and C = seismic dynamic response spectrum values. Accounts for how the building and soil can amplify the basic ground acceleration or velocity.
a v
C and C are determined from respectively '97 UBC tables 16 Q and 16 R as a function of Z, underlying soil conditions, and proximity to a fault. Soil profile type: Using method A,
Page 4 of 7
motion.
When the period of vibration of the building is soil, the bedrock motion is amplified. The predicted by Z alone. The following are
close to the period of vibration of the underlying building experiences larger motions than that generalizations about building response as a stiffness.
Description
Building
Soil
Soft
Higher
The soil profile types are: Description Hard Rock Rock Type S S
A B
Page 5 of 7
Very dense soil and soft rock SC Stiff soil Soft soil See '97 UBC 1629.3.1 S S S
D E F
Specific details about each type can be found in In the absence of a geotechnical site investigation,
D
use S . This is in accordance with '97 UBC 1629.3 Do not confuse this requirement with the one stated in '97 UBC 1630.2.3.2 which applies ONLY when using the simplified design base web site is NOT using these simplified procedures, but is using 1630.2.1. R = response modification factor.
A judgement factor that accounts for building ductiltiy, damping, and over strength. prior to fracture: Ductility = ability to deform in the inelastic range
Page 6 of 7
Over strength = the extra or reserve strength in the structural system. It comes from the practice of designing every member in a group according to the forces in the most critical member of that group.
Structural systems with larger R = better seismic performance. In '97 UBC Table 16 N, R range from 2.8 (light steel frame bearing walls with tension bracing) to 8.5 systems). (special SMRFS of steel or concrete and some dual For bearing wall systems where the wall elements resist both lateral and vertical loads: stories: R = 5.5 N and N = near source factors that are applicable in only seismic zone 4. They account for the very large ground
v v v a
Wood shear panel buildings with 3 or less Masonry shear walls: R = 4.5.
accelerations that occur near the seismic source (the fault). N is generally used with C for structures located < 9.3 miles (15km) from the fault.
Page 7 of 7
N is found in '97 UBC Table 16 T N is used with C for structures located < 6.2 miles (10 km) from the fault.
a a a v
Both N and N are based upon the type of seismic source, A C. This source type, and location of fault, like a current USGS survey. must be established using approved geotechnical data