Professional Documents
Culture Documents
provides information on directly connected devices that have CCNA3 v4.0 download
CDP enabled CCNA4 v4.0 download(updated
5. Refer to the exhibit. What two statements are true 21/7/2008)
based on the output shown? (Choose two.) CCNA 3:Module 7
the reported distance to network 172.16.1.0 is 2172416 CCNA 3:Module 6
192.168.10.5 and 192.168.10.9 are feasible successors CCNA 3:Module 5
neighbors 192.168.10.9 and 192.168.10.5 have auto CCNA 3:Module 4
summary disabled.
CCNA 3:Module 3
router 3 is load balancing traffic to the 172.16.3.0 network
CCNA 3:Module 2
across its serial interfaces.
CCNA 3:Module 1
all interfaces shown on Router3 are in the passive state and
CCNA 2:Final Set 3
will not send EIGRP advertisements
6. Which of the following should be considered when CCNA 2:Final Set 2
troubleshooting a problem with the establishment of CCNA 2:Module 11
neighbor relationships between OSPF routers? (Choose CCNA 2:Module 10
three.) CCNA 2:Module 9
OSPF interval timers mismatch CCNA 2:Module 8
gateway of last resort not redistributed CCNA 2:Module 7
interface network type mismatch
CCNA 2:Module 6
no loopback interface configured
CCNA 2:Module 5
administrative distance mismatch
CCNA 2:Module 4
inconsistent authentication configuration
CCNA 2:Module 3
7. Refer to the exhibit. Which three statements are true
of the routing table for Router1? (Choose three.) CCNA 2:Module 2
The route to network 172.16.0.0 has an AD of 156160. CCNA 2:Module 1
Network 192.168.0.16 can best be reached using CCNA 1:Final
FastEthernet0/0. CCNA 1:Module 11
The AD of EIGRP routes has been manually changed to a CCNA 1:Module 10
value other than the default value. CCNA 1:Module 9
Router1 is running both the EIGRP and OSPF routing
CCNA 1:Module 8
process.
CCNA 1:Module 7
Network 172.17.0.0 can only be reached using a default
CCNA 1:Module 6
route.
CCNA 1:Module 5
No default route has been configured.
CCNA 1:Module 4
8. Refer to the exhibit. The ORL router is unable to form CCNA 1:Module 3
a neighbor relationship with the JAX router. What is a CCNA 1:Module 2
possible cause of this problem? CCNA 1:Module 1
Router JAX has the wrong autonomous-system number.
► July (13)
The command network 192.168.2.0 is missing from the
EIGRP configuration on the JAX router. ► June (13)
Automatic summarization is not disabled on the JAX router.
► May (27)
Router JAX has the wrong IP address on the Fa0/1 interface.
9. Which statement is true regarding routing metrics?
All routing protocols use the same metrics.
LABELS
EIGRP uses bandwidth as its only metric.
CCNA 1 UPDATED (12)
Routers compare metrics to determine the best route.
The larger metric generally represents the better path. CCNA 2 UPDATED (12)
10. Which three statements are true of holddown CCNA 3 UPDATED (7)
timers? (Choose three.) CCNA tieng viet (1)
used by link state routing protocols to prevent routing loops CCNA1 (16)
prevent update messages from reinstating a route that may CCNA2 (20)
have gone bad CCNA3 (10)
allow routers to still forward packets to destination networks
CCNA4 (8)
that are in holddown
Cisco Exploration 4.0 (3)
limit the number of hops a packet can traverse through the
ebook CCNA (2)
network before it is discarded
EbooK_tool_CCNA (7)
prevent a router advertising a network through the same
interface from which the network was learned key_CCNA v4 (3)
permit lower metric updates received from any neighboring key_CCNA4 (13)
router to reinstate the route to a possibly down network Labpro (2)
If hello packets are not received within the hold time, DUAL
must recalculate the topology.
The reported distance is the distance to a destination as
advertised by a neighbor.
EIGRP maintains full knowledge of the network topology in
the topology table and exchanges full routing information
with neighboring routers in every update.
EIGRP builds one routing table that contains routes for all
configured routed protocols.
55. Refer to the exhibit. Which path will traffic from the
172.16.1.0/24 network take to get to the 10.0.0.0/24
network?
ADC
ABC
It will load balance the traffic between ADC and ABC
It will send the traffic via ABC, and will use ADC as a backup
path only when ABC fails.
heirarchical designs.
They are aware of the complete network topology.
They pass their entire routing tables to their directly
connected neighbors only.
They offer rapid convergence times in large networks.
They rely on decreasing hop counts to determine the best
path.
They do not include subnet masks in their routing updates.
0 COMMENTS:
Post a Comment