Professional Documents
Culture Documents
Recycled Content:
25%
Product Description
Materials
A. General:
ASTM C 635 Intermediate-duty main beam classication, ASTM A 653 zinc-coated hot dipped galvanized steel. Exposed surfaces chemically cleansed, zinc-coated and prenished. Materials conform to the performance standard ASTM C 645 (Standard Specication for Rigid Furring Channels for Screw Applications of Gypsum Board). B. Components: 1A. Main Beams: Double-web construction, prole height 1-11/16 with peaked roof top bulb and 1-1/2 knurIed ange HD8906FO8 (144, 1-1/2 ange, 51 routs, pre-notched starting 8 from each end and 8 on center for creating curved instalIations) HD8906F16 (144, 1-1/2 ange, 51 routs, pre-notched starting 4 from one end and 16 on center for creating curved instatIations) Other
1/4" 9/16" 1-11/16"
1-1/2"
2A. Cross Tees: Double-web construction, prole height 1-1/2 with peaked roof top bulb and 1-1/2 knurled ange.
XL8965 (72, 2 routs, starting 24 off each end, galvanized) For Type F light xture compatibility XL8947P (50, 8 routs, starting 10 off each end, galvanized) For Type F light xture compatibility XL8945P (48, 9 routs, center rout and routes starting 10 off each end, galvanized) For Type F light xture compatibility XL7936G90 (36, no routs, galvanized) XL8925 (26, 2 routs, 12 off each end, galvanized) For Type F light xture compatibility XL8926 (24, 3 routs, center rout and 12 off each end, galvanized) For Type F light xture compatibility XL7918 (14, no routs, galvanized) For Type F light xture compatibility Other XL7341 (48, 3 routs starting 12 from each end, galvanized) XL8341 (48, center rout, galvanized) Other
1-1/2"
Typical Applications
Indoor applications Barrel vaults and domes
2B. Cross Tee: Double-web construction, prole height 1-11/16 with peaked roof top bulb and prenished 15/16 ange.
15/16"
CHANNEL MOLDING
suspension systems
HD7859 (120, hemmed angle molding, nominal 1-1/4 x 1-1/4) 7858 (144, hemmed reverse
angle molding, nominal 1-9/16 x 15/16) Other 5. Radius Clip (RC2) is used for drywall applications which form curved installations; attaches to the cavity side of the web of the main beam with four 7/16" pan head screws; install at all knockout locations Accessories: (see Drywall Accessories Submittal Sheet, CS-3082).
1-1/4" (32mm)
ANGLE MOLDING
REVERSE MOLDINGS
Note: RC2 clip must be installed at every knockout location on main beam.
Physical Data
Material Hot dipped galvanized steel Surface Finish Unpainted steel Cross Tee/Main Beam Interface Override End Detail Main Beam: Staked-on clip Cross Tee: Staked-on clip Duty Classication Intermediate-duty Main Beam Load Test Data
HANGER SPACING (Lbs./LF. Simple Span)** MAIN BEAMS LENGTH HD8906F08 144 HD8906F16 144 WEB ASTM HEIGHT CLASS 1-11/16 Intermediate-duty 1-11/16 Intermediate-duty L/240 2 3 4 18.4 18.4 2 L/360 3 4 12.3 12.3
13.0 4.27
1-1/2
Seismic Performance
MAIN BEAMS HD8901 HD8906 CROSS TEES XL7918, XL8926, XL8925, XL7936G90, XL7341, XL8341, XL8945P, XL8947P, XL8965 MINIMUM LBS. TO PULL OUT COMPRESSION/TENSION 348.0 374.0 MINIMUM LBS. TO PULL OUT COMPRESSION/TENSION 377.0
Note: All load test data based on at installation per ASTM C 635
ICC Reports
For areas under ICC jurisdiction, see ICC evaluation report number 1289 for allowable values and/or conditions of use concerning the suspension system components listed on this page. The report is subject to reexamination, revisions and possible cancellation.