You are on page 1of 10

L272

DUAL POWER OPERATIONAL AMPLIFIERS

. . . . . . .

OUTPUT CURRENT TO 1 A OPERATES AT LOW VOLTAGES SINGLE OR SPLIT SUPPLY LARGE COMMON-MODE AND DIFFERENTIAL MODE RANGE GROUND COMPATIBLE INPUTS LOW SATURATION VOLTAGE THERMAL SHUTDOWN

Powerdip (8 + 8)

DESCRIPTION The L272 is a monolithic integrated circuits in Powerdip, Minidip and SO packages intended for use as power operational amplifiers in a wide range of applications including servo amplifiers and power supplies, compacts disc, VCR, etc. The high gain and high output power capability provide superior performance whatever an operational amplifier/power booster combination is required. PIN CONNECTIONS (top view)
Minidip SO16 (Narrow)

ORDERING NUMBERS : L272 (Powerdip) L272M (Minidip) L272D (SO16 Narrow)

L272M

L272D

July 2003

1/10

L272
BLOCK DIAGRAMS L272 L272D L272M

SCHEMATIC DIAGRAM (one only)

2/10

L272
ABSOLUTE MAXIMUM RATINGS
Symbol Vs Vi Vi Io Ip Ptot Supply Voltage Input Voltage Differential Input Voltage DC Output Current Peak Output Current (non repetitive) Power Dissipation at: Tamb = 80C (L272), Tamb = 50C (L272M), Tcase = 90 C (L272D) Tcase = 75 C (L272) Operating Temperature Range (L272D) Storage and Junction Temperature Parameter Value 28 Vs Vs 1 1.5 1.2 5 40 to 85 40 to 150 A A W W C C Unit V

Top Tstg, Tj

THERMAL DATA
Symbol Rth j-case Rth j-amb Rth j-alumina Parameter Thermal Resistance Junction-pins Thermal Resistance Junction-ambient Thermal Resistance Junction-alumina Max. Max. Max. Powerdip 15 70 SO16 ** 50 Minidip * 70 100 Unit
o o o

C/W C/W C/W

* Thermal resistance junction-pin 4 ** Thermal resistance junctions-pins with the chip soldered on the middle of an alumina supporting substrate measuring 15x 20mm; 0.65mm thickness and infinite heatsink.

ELECTRICAL CHARACTERISTICS (VS = 24V, Tamb = 25oC unless otherwise specified)


Symbol Vs Is Ib Vos Ios SR B Ri Gv eN IN CRR SVR Parameter Supply Voltage Quiescent Drain Current Input Bias Current Input Offset Voltage Input Offset Current Slew Rate Gain-bandwidth Product Input Resistance O. L. Voltage Gain Input Noise Voltage Input Noise Current Common Mode Rejection Supply Voltage Rejection f = 100Hz f = 1kHz B = 20kHz B = 20kHz f = 1kHz f = 100Hz, RG = 10k, VR = 0.5V Vs = 24V Vs = 12V Vs = 6V Ip = 0.1A Ip = 0.5A f = 1 kHz; RL =10, Gv = 30dB Vs = 24V Vs = 6V f = 1kHz, Gv = 3 dB, Vs = 24V, RL = 60 500 60 70 50 10 200 75 70 62 56 23 22.5 60 60 0.5 145 % C 3/10 V V dB VO = VS 2 Vs = 24V Vs = 12V Test Conditions Min. 4 8 7.5 0.3 15 50 1 350 Typ. Max. 28 12 11 2.5 60 250 Unit V mA mA A mV nA V/s kHz k dB dB V pA dB dB 54

Vo Cs

Output Voltage Swing Channel Separation

21

d Tsd

Distortion Thermal Shutdown Junction Temperature

L272
Figure 1 : Quiescent Current versus Supply Voltage Figure 2 : Quiescent Drain Current versus Temperature

Figure 3 :

Open Loop Voltage Gain

Figure 4 :

Output Voltage Swing versus Load Current

Figure 5 :

Output Voltage Swing versus Load Current

Figure 6 :

Supply Voltage Rejection versus Frequency

4/10

L272
Figure 7 : Channel Separation versus Frequency Figure 8 : Common Mode Rejection versus Frequency

APPLICATION SUGGESTION NOTE In order to avoid possible instability occuring into final stage the usual suggestions for the linear power stages are useful, as for instance :

- layout accuracy ; - a 100nF capacitor corrected between supply pins and ground ; - boucherot cell (0.1 to 0.2 F + 1 series) between

Figure 9 : Bidirectional DC Motor Control with P Compatible Inputs

Figure 10 : Servocontrol for Compact-disc

Figure 11 : Capstan Motor Control in Video Recorders

5/10

L272
Figure 12 : Motor Current Control Circuit.

Note : The input voltage level is compatible with L291 (5-BIT D/A converter).

Figure 13 : Bidirectional Speed Control of DC Motors. 2R3 R1 For circuit stability ensure that RX > where RM = internal resistance of motor. RM Vs 2R R1 The voltage available at the terminals of the motor is VM = 2 (Vi ) + Ro M where Ro = 2 RX and IM is the motor current.

6/10

L272

DIM. MIN. a1 B b b1 D E e e3 F I L Z 0.38 0.51 0.85

mm TYP. MAX. MIN. 0.020 1.40 0.50 0.50 20.0 8.80 2.54 17.78 7.10 5.10 3.30 1.27 0.015 0.033

inch TYP. MAX.

OUTLINE AND MECHANICAL DATA

0.055 0.020 0.020 0.787 0.346 0.100 0.700 0.280 0.201 0.130

Powerdip 16
0.050

7/10

L272
mm DIM. MIN. A a1 B b b1 D E e e3 e4 F I L Z 3.18 7.95 2.54 7.62 7.62 6.6 5.08 3.81 1.52 0.125 0.51 1.15 0.356 0.204 1.65 0.55 0.304 10.92 9.75 0.313 0.100 0.300 0.300 0.260 0.200 0.150 0.060 TYP. 3.32 0.020 0.045 0.014 0.008 0.065 0.022 0.012 0.430 0.384 MAX. MIN. TYP. 0.131 MAX. inch

OUTLINE AND MECHANICAL DATA

Minidip

8/10

L272

DIM. MIN. A a1 a2 b b1 C c1 D (1) E e e3 F (1) G L M S 3.8 4.6 0.4 9.8 5.8 0.35 0.19 0.1

mm TYP. MAX. 1.75 0.25 1.6 0.46 0.25 0.5 45 (typ.) 10 6.2 1.27 8.89 4 5.3 1.27 0.62 8(max.) 0.150 0.181 0.016 0.386 0.228 0.014 0.007 0.004 MIN.

inch TYP. MAX. 0.069 0.009 0.063 0.018 0.010 0.020

OUTLINE AND MECHANICAL DATA

Weight: 0.20gr

0.394 0.244 0.050 0.350 0.157 0.209 0.050 0.024

SO16 Narrow

(1) D and F do not include mold flash or protrusions. Mold flash or potrusions shall not exceed 0.15mm (.006inch).

0016020
9/10

L272

Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics 2003 STMicroelectronics Printed in Italy All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. http://www.st.com

10/10

You might also like