You are on page 1of 30

Plasma Flat Panel

42 PDP Monitor

Owners Manual

Important Safety Instructions


WARNING
RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock, do not remove the front or back covers. No user-serviceable parts inside. Refer servicing to qualified service personnel only.
The lightning flash with arrow-head within a triangle is intended to inform the user that parts inside the product are a risk of electric shock. The exclamation point within a triangle is intended to tell the user that important operating and servicing instructions are explained.

Special Notices

Certain programs may be copyrighted and any unauthorized recording in whole or in part may be in violation of copyright laws in the U.S. and Canada. FCC/CSA regulations state that any unauthorized modifications to this display may void user authority to operate it.

Warnings & Precautions


Read these insturctions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturers instruction. Do not install near any heat sources such as radiators. Heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and third grounding prong. The wide blade or the third prong are provided for you safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/ accessories specified by the manufacturer. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over. Unplug this apparatus during lightning storms or when unused for long periods of time. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in amy way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Attention, consult accompanying documents with respect to electric Shock, The symbol in figure shall be shown adjacent to the text of time 12 above.

Important Safety Instructions

Avoid overhead power lines. An outdoor antenna system should not be placed in the vicinity of overhead power lines, electric lights, or power circuits. When installing an outdoor antenna, be careful to not touch any power lines or circuits as contact with these lines can be fatal. Do not insert any foreign objects through the ventilation openings to the display. It may touch dangerous voltage points or damage parts. If an outdoor antenna or cable system is connected to the display, be sure the antenna or cable system is grounded to provide some protection against voltage surges and static charge buildups. Section 810 of the National Electrical Code, ANSI/NFPA No.70-1984, provides information about proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. If this display is equipped with separate speakers, please remove the speakers prior to moving the display. Moving the display with the speakers attached may cause damage or injury. Disconnect the unit from the main supply and refer servicing to qualified service personnel under the following conditions: - Power cord or plug is damaged or frayed. - Liquid has been spilled into the product and/or the unit has been exposed to water or moisture. - Unit does not operate normally when the operating instructions are not followed. Adjust only those controls that are covered by the operating instructions, improper adjustment of other controls may result in damage which often requires extensive work by a qualified technician to restore the unit to normal operation. - Unit has been dropped or the cabinet has been damaged. - Unit exhibits a distinct change in performance, indicating a need for service.

Cleaning & Maintenance

Disconnect from the electric outlet before cleaning. Do not use liquid or aerosol cleaners. Use only a slightly damp cloth for cleaning.

Special Warranty Information


Cell Defects

Although the display panels are produced with more than 99% percent active cells, there may be some cells that do not produce light or remain lit. This is considered normal and not a manufacturer defect.

Regulatory Notice
FCC Statement
The Federal Communications Commission Radio Frequency Interference Statement includes the following warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television receptions, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help.

Warning
User must use shielded signal interface cables to maintain FCC compliance for the product. Provided with this display is a detachable power supply cord with IEC320 style terminations. It may be suitable for connection to any UL Listed personal computer with similar configuration. Before making the connection, make sure the voltage rating of the computer convenience outlet is the same as the monitor and that the ampere rating of the computer convenience outlet is equal to or exceeds the monitor voltage rating. For 120 Volt applications, use only UL Listed detachable power cord with NEMA configuration 5-15P type (parallel blades) plug cap. For 240 Volt applications use only UL Listed Detachable power supply cord with NEMA configuration 6015P type (tandem blades) plug cap.

IC Compliance Notice
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations of ICES-003. Cet appareil Numerique de classe B respecte toutes les exigences du Reglemont NMB-03 sur les equipements produisant des interferences au Canada.

Notice de Conformit IC
Cet appareil numerique de classe B respecte toutes les exigences du Reglement ICES-003 sur les equipements produisant des interferences au Canada.

Table of Contents
Important Safety Instructions ................................................................................................................... 2 Special Notices ................................................................................................................................. 2 Warnings & Precautions ................................................................................................................... 2 Cleaning & Maintenance ................................................................................................................... 3 Special Warranty Info ........................................................................................................................ 3 Regulatory Notice .................................................................................................................................... 4 Getting to Know Your Display .................................................................................................................. 7 Package Contents ............................................................................................................................ 8 Front Panel Controls ......................................................................................................................... 9 Rear Panel Connections ................................................................................................................... 10 Remote Control ................................................................................................................................. 11 Display Connections ............................................................................................................................... 13 Connecting a VCR ............................................................................................................................ 14 Connecting a DVD ............................................................................................................................. 15 Connecting a Set-Top Box ................................................................................................................ 17 External Audio Connections .............................................................................................................. 18 Connecting a PC .............................................................................................................................. 19 RS-232 Connection ........................................................................................................................... 21 Basic Operations ..................................................................................................................................... 25 Powering On/Off................................................................................................................................ 26 Change Inputs ................................................................................................................................... 26 Volume Adjustment ........................................................................................................................... 27 On-Screen Display Menu .................................................................................................................. 28 On-Screen Status Display................................................................................................................. 29 Understanding Widescreen Modes .................................................................................................... 30 Changing Aspect Ratios .................................................................................................................... 31 Picture Controls ...................................................................................................................................... 33 Adjusting Picture Settings ................................................................................................................. 34 Picture-in-Picture .............................................................................................................................. 36 Noise Reduction ............................................................................................................................... 38 Imagie Shift ...................................................................................................................................... 39 Adjusting Screen Size ...................................................................................................................... 40 Picture Mode .................................................................................................................................... 41 Quick Access Menu ......................................................................................................................... 42 Sound Controls ....................................................................................................................................... 43 Adjusting Sound Settings ................................................................................................................. 44 Using Surround Sound ...................................................................................................................... 45 Built-in Amplification (Speaker) ......................................................................................................... 47 Fixed / Variable Audio Output ........................................................................................................... 48 Advanced Functions ................................................................................................................................ 49 Sleep Timer ...................................................................................................................................... 50 OSD Menu Language ........................................................................................................................ 50 Full White ......................................................................................................................................... 51 Power Save Mode ............................................................................................................................. 52 Multi-Color ........................................................................................................................................ 52 Information Display............................................................................................................................ 53 Advanced Functions Setup ............................................................................................................... 54 Understanding HDTV ......................................................................................................................... 55 Appendix ................................................................................................................................................. 57 Troubleshooting ................................................................................................................................ 58 Wall Mount Insturctions Guide .......................................................................................................... 59 Specifications ................................................................................................................................... 61 Index ................................................................................................................................................ 63

Table of Contents

Flat Panel Monitor

Getting to Know Your Display

Getting to Know Your Display


Package Contents

Flat Panel Display

Remote Control

Batteries

User Manual

Power Cord

Quick Start Guide

Warranty Card

Getting to Know Your Display


Front Panel Controls

IR Sensor Status LED


Orange - Standby (Power OFF) with AC power detected. The LED will illuminate in orange color if the monitor is shut-off but the main power cord is plugged into the back of the unit. Solid Green - Power ON

Volume Adjustment Buttons


Use these buttons to adjust volume up and down. These keys also serve as navigation and adjustment keys when On Screen Display menu is engaged.

Select Buttons
Use these buttons to navigate through the On Screen Display menu.

Menu Button
Use this button to engage the On Screen Display menu.

Power (Standby) Button


Turns power on/off from standby mode.

Input Button
Use this button to switch between available inputs.

Getting to Know Your Display


Rear Panel Connections

Composite / S-Video Inputs


Connect Composite or S-Video signals from external sources such VCRs or DVD players.

RGB Input
Connect to RGB output of computer or Set-Top Box.

Component Video Inputs


Auto-detecting component video inputs (Y/Pb/Pr or Y/Cb/Cr) for connecting to the component output of a DVD player or Set-Top Box.

Digital HDMI Inputs


Connect to the digital video signals from a Set-Top Box .

RS-232 Connector
Connect to a computer serial port.

Audio Output
Variable or fixed audio output for connecting to an external audio amplifier.

10

Getting to Know Your Display


Remote Control
Standby Power On/Off
Push this button to turn on the monitor from Standby mode. Push it again to turn off to Standby mode.

Number Keypad
These keys are not applicable to this monitor.

Input Select
Press to select input signal modes sequentially.

Sound Mute On/Off


To switch the sound off and back on again.

Smart ID
This key is not available for this monitor.

Display
Press to show the status of the monitor.

WIDE
Toggles between various aspect ratio settings.

Select Up/Down
Press to navigate through the On Screen Display menu.

Volume/Adjust Up/Down
Press to turn volume up or down. These keys also serve as navigation and adjustment keys when On Screen Display menu is engaged.

Menu
Engages the OSD menu.

Quick Access Menu


Engages Quick Access menu.

Recall
Recalls default picture settings.
13

PIP (Picture-in-Picture Button)


Turns on PIP (Picture-in-Picture) feature under HDMI input mode. Press it again to turn off PIP feature.

13

PIP Source
Changes the input source of the PIP sub-window among AV/Component input sources.

Swap
This key is not applicable to this monitor.

PIP Position
This key changes the PIP sub-window to 4 different corner locations.

Note: RGB 2 direct input key is not applicable to this monitor.

11

Getting to Know Your Display


Remote Control (cont)
Closed Captioning
Turns on Closed Captioning Mode.

Picture Mode
Press to select Picture Modes sequentially.

3D Digital COMB
Filter Direct key. Turns 3D Digital Comb Filter on and off.

Sleep Timer
Engages Sleep Timer settings.

Direct Input Selection Keys


Directly change input signal selection by pressing the appropriate key.
22

Discrete Power ON/OFF


Press OFF to send monitor into standby mode. Press ON to power on from standby mode.

22

Battery Installation

12

Flat Panel Monitor

Display Connections

13

Display Connections
Connecting a VCR Using S-Video Input
Connect the S-Video (4-pin DIN) connector from the VCR to the S-Video input on the back of monitor. Connect the red (R) and white (L) audio output from the VCR to the R and L audio input located next to the S-Video connector. Note: There are two sets of S-Video inputs provided. For TV Channels setup please refer to VCR user manual for details.

Ant. In

Antenna

Using Composite Input


Connect the Video (yellow) out connector from the VCR to the Video (yellow) input on the back of monitor. Connect the red (R) and white (L) audio output from the VCR to the R and L audio input located next to the Video (yellow) connector.

Note: There are two sets of composite inputs provided. For TV Channels setup please refer to VCR user manual for details.

Ant. In

Antenna

14

Display Connections
Connecting a DVD Using Component Video Input
There are two sets of component video inputs provided. You can use either set of component inputs to connect your DVD. Connect the green-colored (labeled as Y) jack from the DVD to the green-colored jack of the monitor. Connect the red-colored (labed as PR or CR) jack from the DVD to the red-colored PR/CR jack of the monitor. Connect the blue-colored (labed as PB or CB) jack from the DVD to the blue-colored PB/CB jack of the monitor. Connect the red (R) and white (L) audio jacks from the DVD to the R and L audio-in jacks located next to the PR/CR connector. Note: There are two sets of component inputs provided.

15

Display Connections
Connecting a DVD (cont) Using S-Video Input
Connect the S-Video (4-pin DIN) connector from the DVD to the S-Video input on the back of monitor.

Connect the red (R) and white (L) audio jacks from the DVD to the R and L audio-in jacks located next to the S-Video connector.

Note: There are two sets of S-Video inputs provided.

Using Composite Input


Connect the Video (yellow) out connector from the DVD to the Video (yellow) input on the back of monitor. Connect the red (R) and white (L) audio-out jacks from the DVD to the R and L audio-in jacks located next to the Video (yellow) connector.

Note: There are two sets of composite inputs provided.

16

Display Connections
Connecting a Set-Top Box Using Component Video Input
There are two sets of component video inputs provided. You can use either set of component inputs to connect your Set-Top Box. Some HDTV Set-Top Boxes may not have a Component Video output. Instead, use RGB input method. Connect the green-colored (labeled as Y) jack from the Set-Top Box to the green-colored jack of the monitor. Connect the red-colored (labed as PR or CR) jack from the Set-Top Box to the red-colored PR/CR jack of the monitor. Connect the blue-colored (labed as PB or CB) jack from the Set-Top Box to the blue-colored PB/CB jack of the monitor. Connect the red (R) and white (L) audio jacks from the Set-Top Box to the R and L audio-in jacks located next to the PR/CR connector.

Using RGB Input


Connect the 15-pin D-Sub RGB connector from the back of the HDTV Set-Top Box to the RGBIN Connector located on the back of the monitor. Connect the red (R) and white (L) audio-out jacks from the HDTV Set-Top Box to the R and L audio-in jacks located next to the RGB connector.

Notes: Some HDTV Set-Top Boxes may not have a RGB output. Use Component Video input or HDMI input method if this is the case. Upon connecting your HDTV Set-Top Box to the RGB input of the monitor, it may be necessary to adjust various picture settings on the monitor to correctly match the output of the HDTV Set-Top Box. This is caused by the different video timings set by various HDTV Set-Top Box manufacturers.

17

Display Connections
Connecting a Set-Top Box (cont) Using HDMI Input
Connect the HDMI connector from the back of the HDTV Set-Top Box to the HDMI Connector located on the back of the monitor.
-

HDMI Cable

HDMI

Notes: Some HDTV Set-Top Boxes may not have a HDMI output. Use Component Video input or RGB input method if this is the case. Upon connecting your HDTV Set-Top Box to the HDMI input of the monitor, it may be necessary to adjust various picture settings on the monitor to correctly match the output of the HDTV Set-Top Box. This is caused by the different video timings set by various HDTV Set-Top Box manufacturers.

External Audio Connections Connecting to an External Amplifiers


This monitor can be connected to an external amplifier using the AUDIO OUT jacks located on the back of the monitor. Connect the red (R) and white (L) AUDIO OUT jacks from right side of the connector panel to the external amplifier. Note: The AUDIO OUT RCA jacks can be set to either Fixed or Variable audio output levels.

18

Display Connections
Connecting a PC Using RGB Video Input
For most PCs, connect the 15-pin D-Sub RGB connector from the back of the PC to the RGBIN Connector located on the back of the monitor. Connect the red (R) and white (L) audio jacks from the PC to the R and L jacks located next to the RGB connector. Note: A RGB loop-out labeled RGB Out will allow another RGB monitor to be connected. The RGB loop-out will display the same signal as the RGB In signal source.
RGB Cable (15 Pin D-Sub) Audio (3.5 mm Mini-Stereo to RCA cable)

Setting Up Your Monitor Using Plug and Play


This monitor adheres to VESA Plug and Play standard to eliminate complicated and time consuming setup of monitors. This monitor identifies itself to the computer and automatically sends the PC its Extended Display Identification Data (EDID) using Display Data Channel (DDC) protocols.

How to Set up Your PC for Use with Monitor (Windows)


The display settings for a typical Windows-based computer are shown below; however, actual screens on your computer will differ depending on the version of Windows and video card equipped with the computer. Even though the actual screen may look different from example displayed below, basic set-up routine will apply in most cases.

Go to Windows CONTROL PANEL by clicking: START, SETTINGS, CONTROL PANEL. The CONTROL PANEL Window is displayed. Select the DISPLAY icon from this window.

19

Display Connections
Connecting a PC (cont)
The DISPLAY PROPERTIES dialog box is displayed. Select the SETTINGS tab to display your computers video output settings. Set the Screen Resolution settings to 1024x768 PIXELS. For COLOR QUALITY, select 32 BIT COLOR (might also be expressed as 16 million colors). If a vertical-frequency option exists, set the value to 60 or 60 Hz. Click OK to complete the setting. Note: Both screen position and size will vary, depending on the type of PC graphics card and its resolution selected.

Supported Resolutions
This monitor supports the following resolutions Horizontal Dot x Line 720 x 400@70Hz 640 x 480@60Hz
2

Vertical Frequency (Hz) 70.087 59.940 59.835 60.317 60.004 60.020 59.940 60.000 60.000 Dot Rate (MHz) 28.322 25.175 30.000 40.000 65.000 108.000 27.000 74.250 74.250 Vertical Polarity + + + + + Horizontal Polarity + + + +

Frequency (KHz) 31.469 31.469 31.413 37.879 48.363 63.981 31.469 45.000 33.750

852 x 480@60Hz 800 x 600@60Hz 1024 x 768@60Hz 1280 x 1024@60Hz 720 x 480p@60Hz 1280 x 720p@60Hz 1920 x 1080i@60Hz

3
4

4
4

Note: This monitor does not support Macintosh resolutions. Resolution with 2 is only available for 42 ED Monitor. Resolution with 3 is only available for 42 HD Monitor. Resolutions with 4 are type of video signal.

20

Display Connections
RS-232 Connection Overview
This monitor is equipped with an RS-232 serial terminal for using the monitor with computer controls. The RS-232 serial terminal conforms to the RS-232C interface specification. The computer will require software application (such as HyperTerminal) which allows the computer to send and receive control data that can support the communication parameters described in this section.

Interface Parameters
These parameters are required to setup communications with the monitor. RS-232C Pint Layout Specification RS-232C Pin 1 Received Line Signal Detector (Data Carrier Detect) Sync Method Synchronous Pin 2 Received Data (RXD) Baud Rate 9600 bps Pin 3 Transmit Data (TXD) Parity None Pin 4 Data Terminal Ready (DTR) Character Length 8 Bits Pin 5 Signal Ground Stop Bit 1 Bit Pin 6 Data Set Ready (DSR) Pin 7 Request To Send (RTS) Pin 8 Clear To Send (CTS) Pin 9 Ring Indicator

Command Format and Sequencing


Data Structure Overview
In order to transmit data from the computer to the monitor, the data must be sent in a structured format. The format used by this monitor follows a COMMAND:DATA sequence. All commands and its related data are formatted using a 3-character format separated by a colon in-between. For example, the Power On command is sent as: PWR:PON where PWR is telling the monitor that it is receiving a Power related command, followed by the actual command to carry out.

Communications Overview
As commands are sent from the PC, the monitor will provide feedback regarding the state of command execution back to the PC. The monitor provides information status to inform: 1. Whether the command sent by the computer was received by the monitor. 2. Whether the COMMAND:DATA structure was correctly formatted for execution by the monitor. 3. Whether the command sent was successfully carried out by the monitor.

21

Display Connections
The following is an example of the communication process between the PC and the monitor using a program such as HyperTerminal. Example: Read Power Status followed by Power On command and input select to AV1 with disruption PC Status
Send command to read power status Rcv acknowledgment of command received Rcv OFF status from monitor Rcv confirmation of command complete Send command to POWER ON the monitor Rcv acknowledgment of command Rcv confirmation of command complete Send command to switch to AV1 input Rcv acknowledge of command not accepted Send command to void previous command Rcv acknowledgment of command received Rcv confirmation of command complete Send command to switch to AV1 input again Rcv acknowledgment of command received Rcv confirmation of command complete Ready to send another command

Monitor Status
Monitor rcvs command Sends confirmation of command rcvd to PC Sends actual status of power to PC (OFF) Sends confirmation of command completion Monitor is not busy and waiting for command Sends confirmation of command rcvd to PC Monitor powers on and sends confirmation Monitor is busy doing another task Sends busy status because it cant rcv data Rcvs command to clear previous command Sends confirmation of command rcvd to PC Clears command buffer and sends confirm Monitor is not busy and rcvs command Sends confirmation of command rcvd to PC Monitor switches to AV1 and sends confirm Monitor is ready to accept another command

Command and Data Tables


Description
Read Data Volume Power On/Off Brightness Contrast Color Tint Sharpness Input Select V-Size V-Position H-Size H-Position Recall Mute Language Bass Treble Balance Surround Sound Closed Captioning Aspect Ratio PIP PIP Position

Command
REA VOL PWR BRT CON CLR TNT SHP INP VSZ VPS HSZ HPS RCL MUT LNG BAS TRB BAL SRS CCD ZOM PIP PIS

Data Options
VOL, PWR, BRT, CON, CLR, TNT, SHP, INP, VSZ, VPS, HSZ, HPS, RCL, MUT, LNG, BAS, TRB, BAL, SRS, CCD, ZOM, PIP, PIS,SIN, IKP, DZM, BI3, B14,BI5, PTM 001100 PON=Power On, OFF=Power Off 001100 001100 001100 001100 001100 AV1=AV Input 1, AV2=AV Input 2, CP1=Component Input 1,CP2=Component Input 2, RG1=RGB, HDM=HDMI 001....100 001100 001100 001100 000 MON=On, OFF=Off ENG=English, SPA=Spanish, FFR=French 001.100 001100 001100 OFF=Off, STR=Stereo, MON=Mono OFF, CC1, CC2, CC3, CC4, TX1, TX2, TX3, TX4 WID=16:9, PAN=Panorama Stretch, NOR=4:3 with black bars PON=PIP On, OFF=PIP Off PS1=Position 1, PS2=Position 2, PS3=Position 3, PS4=Position 4

22

Display Connections
Description
Sub-Source Input Skip Default Aspect Image Shift Full White Multi-Color Picture Mode Power on Sequence Sleep Timer

Command
SIN IKP DZM BI3 BI4 BI5 PTM POQ SLP

Data Options
AV1=AV Input 1, AV2=AV Input 2,CP1=Component Input 1, CP2=Component Input 2, NOR= Normal, AV1=AV Input 1, AV2=AV Input 2, CP1=Component 1, CP2=Component 2, RG1=RGB, HDM=HDMI WID=16:9, PAN=Panaorama Stretch, NOR=4:3 with black bars OFF=Turn Off, 10S=10 Sec, 20S=20 Sec, 30S=30 Sec OFF=Turn Off, 10M=10 Min, 60M=60 Min OFF=Turn Off, 10M=10 Min, 60M=60 Min CNM=Cinema, VVD=Vivid, STD=Standard, USR=User 1ST=1 STEP, 2ST=2 STEP OFF=OFF, 15M=15 MIN, 30M=30 MIN, 45M= 45 MIN, 60M=60 MIN, 90M=90 MIN, 1H2=120 MIN

23

Display Connections

24

Flat Panel Monitor Basic Operations

Basic Operations

25

Basic Operations Basic Operations


Powering On/Off Using Front Panel or Remote Control
Make sure the monitor is plugged into the wall outlet. If the power is plugged, the STATUS LED will illuminate in orange color. Press the control. key on the panel or the remote POWER (Toggle)

The monitor will now turn on after a brief pause. The STATUS LED will now turn green to indicate power on status. To turn power off, simply press the key on the panel or the remote control once again.

Using Discrete Power ON/OFF Keys


The discrete POWER ON/OFF keys send two discrete signals to the monitor, one for ON and one for OFF. Because signals are discrete, these keys can be used by third-party universal remote controls for macro programming. To turn power on, simply press the button. If the monitor is turned on already, pressing this button will have no effect. To turn off power, simply press the button. If the monitor is already turned off, pressing this button will have no effect.

Discrete POWER ON/OFF

Changing Inputs Using Front Panel or Remote Control


Press the INPUT key on the panel or the key on the remote control. Pressing the INPUT key will cycle the monitor through all available input signal sources in the following order:
AV1 HDMI AV2 RGB COMPONENT1 COMPONENT2

Input Select (Toggle)

26

Basic Operations
Using Direct Input Selection Keys
If you prefer not to cycle thru all available inputs, you can use the Direct Input Selection keys located towards the bottom of the remote control. Simply select the input that you would like to switch to and press the Direct Input Selection key for that input. Direct Input Selection Keys

Volume Adjustment Using Front Panel or Remote Control


To turn up sound volume, press VOLUME + on either the front panel of monitor or on the remote control. To turn down sound volume, press VOLUME on either the front panel of monitor or on the remote control.

VOLUME +/-

Using MUTE
If you would like to silence the volume on a temporary basis, simply press the key to silence the volume. When the monitors volume is muted, the monitor will display MUTE on the upper right corner of the screen. To disengage the mute mode, simply press the key again or the volume buttons. MUTE

27

Basic Operations
On-Screen Display Menu Accessing OSD Menu via Remote Control or Front Panel
The On-Screen Display (OSD) menu allows access to setup various parameters equipped with this display. To access the OSD menu, press button on the front panel of monitor or press NENU key located on the remote control. OSD Menu Navigation OSD Menu Access

Navigation through the OSD Menu can be accomplished using the arrow keys on the remote control or using the front panel control keys.

OSD Menu Timeout Setting


OSD Menu will automatically disappear after a preset period of time so that it doesnt remain on the screen. To change the OSD timeout period, please follow the steps below. Access the OSD menu, select SETUP submenu. Use keys to highlight OSD
H i

TIMEOUT. Press

keys to confirm selection.


O SD

O SD

LANGUAGE SLEEP TIMER OSD TIMEOUT OSD BACKGROUND POWER SAVE FULL WHITE MULTI-COLOR PREV. MENU

5 SEC GRAY OFF OFF OFF

The OSD Timeout window is displayed. Use keys to adjust your settings. Press keys to confirm selection.
OSD TIMEOUT 5 SEC 5 MIN 10 SEC 30 SEC

28

Basic Operations
OSD Background Color Setting
The background color of the OSD Menu can be customized. To change the OSD Background color setting, please follow the steps below. Access the OSD menu, select SETUP submenu. Use keys to highlight OSD BACKGROUND. Press selection. keys to confirm
O SD

H i

O SD

LANGUAGE SLEEP TIMER OSD TIMEOUT OSD BACKGROUND POWER SAVE FULL WHITE MULTI-COLOR PREV. MENU

5 SEC GRAY OFF OFF OFF

The OSD BACKGROUND window is displayed. Use keys to adjust your settings. Press keys to confirm selection.

On-Screen Status Display


Displaying Status
The On-Screen Status Display shows detailed information regarding the operational status of the monitor. The status display automatically appears whenever there is a change in the state of the monitor such as channel change or input change. The status display will automatically disappear after a timeout period. To manually show the Status Display, simply press the key on the remote control. AV Mode
A V1

Input Source

Note: When using AV1 and AV2, priority is given to the S-Video input. When using S-video connection AV1 and AV2, the status display will denote [S] to indicate the input source is using S-Video connector.

Component Mode / HDMI Mode Input Source COMPONENT1 1080I Signal Format

RGB Mode
RGB 640x480

Input Source Signal Format

29

Basic Operations
Understanding Widescreen Modes
This monitor is capable of displaying a widescreen image on the native 16:9 aspect ratio screen. However, not all available video content fits perfectly in a widescreen (16:9) format resulting in unused screen space. This monitor is capable of displaying images in various formats that is suitable for various types of content depending on its size.

For 4:3 (Square) Content


Content from traditional TV, VCR, and some DVDs are formatted using a square 4:3 format. When viewing content in this Square format the following viewing modes are suitable.

4:3 (NORMAL)
In 4:3 mode, the original 4:3 image is preserved but black bars are used to fill the the extra space on the left and right.

16:9 (FULL)
The original 4:3 image is proportionally stretched to fill the entire screen. This is the default setting from factory.

PANORAMA
The original 4:3 image is expanded in both the horizontal and vertical directions. The center of the picture is almost normal while the edges are considerably expanded.

30

You might also like