Professional Documents
Culture Documents
D D D D D D D D D
Single Chip Mixer/Oscillator and Synthesizer VHF-L, VHF-H, UHF 3-Band Local Oscillator I2C Bus Protocol Bidirectional Data Transmission 30-V Tuning Voltage Output 4-Channel NPN Type Band Switch Drivers Programmable Reference Divider Ratio (512, 640 or 1024) 5-V Power Supply 32-Pin TSSOP Package
description
SN761672A is a single chip synthesized tuner IC designed for TV/VCR tuning systems. The circuit consists of a PLL synthesizer, 3-band local oscillators and mixer, a 30-V output tuning NC No internal connection amplifier, and four NPN band switch drivers. It is available in a small package outline. The 15-bit programmable counter and reference divider is controlled by I2C bus protocol. Tuning step frequency is selectable by this reference-divider ratio for a 4-MHz crystal oscillator.
VOL OSC B VOL OSC C OSC GND VHS OSC B VHS OSC C UHF OSC B1 UHF OSC C1 UHF OSC C2 UHF OSC B2 IF GND IF OUT1 IF OUT2 VCC CP VTU XTAL
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17
UHF RF IN2 UHF RF IN1 VHF RF IN2 VHF RF IN1 RF GND MIX OUT2 MIX OUT1 BS4 BS3 BS2 BS1 NC ADC AS SDA SCL
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright 2001, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters.
block diagram
UHF OSC B1 UHF OSC C1 UHF OSC C2 UHF OSC B2 VOL OSC B VOL OSC C VHI OSC B VHI OSC C MIX OUT1 MIX OUT2 OSC GND
VHF-L OSC
VHF-H OSC
UHF OSC
VHF Mixer
UHF Mixer
1/8 Prescaler
CP VTU
XTAL
512/640/1024 Prescaler
Phase Detector
Charge Pump
NPN Band Switch Port SCL SDA AS NC 5-Level ADC I2C Bus Interface
BS1
BS2
BS3
ADC
BS4
Terminal Functions
TERMINAL NAME ADC AS BS1 BS2 BS3 BS4 CP IF GND IF OUT1 IF OUT2 MIX OUT1 MIX OUT2 OSC GND RF GND SCL SDA UHF OSC B1 UHF OSC B2 UHF OSC C1 UHF OSC C2 UHF RF IN1 UHF RF IN2 VCC VHF RF IN1 VHF RF IN2 VHI OSC B VHI OSC C VLO OSC B VLO OSC C VTU XTAL NO. 20 19 22 23 24 25 14 10 11 12 26 27 3 28 17 18 6 9 7 8 31 32 13 29 30 4 5 1 2 15 16 I I O I O O I I I/O I I O O I O O O I/O I I O ADC input (see Figure 7) Address selection input (see Figure 7) Band switch1 output (NPN emitter follower) ( see Figure 8) DESCRIPTION
Charge pump output (see Figure 5) IF ground (see Figure 4) IF output (see Figure 4) IF output (see Figure 4) Mixer outputs (see Figure 9) OSC ground RF ground Serial clock input (see Figure 7) Serial data input/output (see Figure 7) UHF oscillator input, base 1 (see Figure 3) UHF oscillator input, base 2 (see Figure 3) UHF oscillator output, collector 1 (see Figure 3) UHF oscillator output, collector 2 (see Figure 3) UHF RF inputs (see Figure 11) Supply voltage for mixer/oscillator/PLL: 5 V VHF RF inputs (see Figure 10) VHF hi oscillator input base (see Figure 2) VHF hi oscillator output collector (see Figure 2) VHF low oscillator input base (see Figure 1) VHF low oscillator output collector (see Figure 1) Tuning voltage amplifier output (see Figure 5) 4-MHz crystal oscillator input (see Figure 6)
schematics
1 3 k 3 k
4 3 k 3 k
Figure 1
Figure 2
7 11 12
9 3 k 3 k
Figure 3
15
Figure 4
16 14
Figure 5
Figure 6
schematics (continued)
18 17 19
20
Figure 7
Figure 8
Figure 9
29 3 k
30
31 3 k
32
Figure 10
Figure 11
absolute maximum ratings over operating free-air temperature (unless otherwise noted)
Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.4 V ~ 7 V Input voltage 1, VI(GND) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.4 V ~ 0.4 V Input voltage 2, VI(VTU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.4 V~ 35 V Input voltage 3, V(VTU) (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.4 V ~ 7 V Continuous total dissipation at (or below TA = 25C . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating free-air temperature, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20C to 85C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65C to 150C Maximum junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150C Maximum lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . 260C Maximum short circuit time, t(SCMAX), All pins to VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBD
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE 1: Voltage values are with respect to the IF GND of the circuit. DISSIPATION RATING TABLE PACKAGE DA TA 25C POWER RATING 1040 mW OPERATING FACTOR TA 25C 8.33 mW/C
CAUTION: It is advised that precautions to be taken to avoid damage due to high static voltages or electrostatic fields in handling this device. Pins 46 and 9 withstand 150 V, and all other pins withstand 200 V, according to EIAJ (0 , 200 pF).
electrical characteristics
total device and serial interface (VCC 4.5 V to 5.5 V, TA = 20C to 85C) (unless otherwise noted)
PARAMETER ICC(1) ICC(2) VIH VIL IIH IIL V(POR) V(ASH) V(ASM) V(ASL) I(ASH) I(ASL) V(ADC) IIL(ADH) IIL(ADL) f(SCL) th(HLD) VOL Ilkg(SDA) Supply current 1 Supply current 2 High-level input voltage (SCL, SDA) Low-level input voltage (SCL, SDA) High-level input current (SCL, SDA) Low-level input current (SCL, SDA) Power on reset supply voltage High Address select input voltage (AS) Mid Low Address select input current (AS) ADC input voltage ADC high-level input current ADC low-level input current Clock frequency (SCL) Data hold time Low-level output voltage (SDA) High-level output leakage current (SDA) See timing chart, Figure 1 VCC = 5 V, V(SDA) = 5.5 V IOL = 3 mA 0 0.4 10 High Low See Table 9 V(ADC) = VCC V(ADC) = 0 V 10 0 10 100 400 VCC 10 Threshold of supply voltage between reset and operation mode 0.9 VCC ~ VCC 0.4 VCC ~ 0.6 VCC 0 VCC ~ 0.1 VCC 10 2.1 4.5 2 2.8 3.5 5 3 0.5 10 A V A A kHz s V A V One band switch ON I(BS) = 10 mA 3 1.5 10 TEST CONDITIONS MIN TYP 60 70 MAX 80 90 UNIT mA mA V V A A V
PLL and band switch (VCC 4.5 V to 5.5 V, TA = 20C to 85C) (unless otherwise noted)
PARAMETER N F(XTAL) Z(XTAL) V(VTUL) I(VTUOFF) I(CPH) I(CPL) V(CP) I(CPOFF) I(BS) V(SBS1) V(SBS2) Ilkg(BSOFF) Divider ratio Crystal oscillator Crystal oscillator input impedance Tuning amplifier low-level output voltage Tuning amplifier leakage current (OFF) Charge pump high-level input current Charge pump low-level input current Charge pump output voltage Charge pump leakage current Band switch driver output current Band switch driver output voltage Band switch driver leakage current I(BS) = 10 mA I(BS) = 10 mA, TA = 25C V(BS) = 0 V 3 VCC = 5 V, 3.5 3.9 3 V A RL = 27K, OS = 1, CP = 1 CP = 0 In-lock T2 = 0, T1 = 1, TA = 25C VCP = 2 V, 15 V(TU) = 33 V V(TU) = 33 V 0.2 TEST CONDITIONS 14-bit frequency word 15-bit frequency word RXTAL = 25 to 300 MIN 256 256 4 1.6 0.3 280 60 1.95 15 10 0.46 10 TYP MAX 16383 32767 MHz k V A A A V nA mA UNIT
function description
The device can be controlled according to the I2C bus format. Table 1. Serial Interface Function
PIN 17 18 19 20 PIN NAME SCL SDA AS ADC FUNCTION Clock input Data input/output Address selection input ADC input/test output
Band switch ports control bits BSn=0:OFF Band selection by BS1,2,4 (X = dont care) VHF-LO VHF-HI UHF BS1 1 X X BS2 0 1 X
Dont care
NOTES: 6. Not used for other bit-patterns. 7. Main counter input is bypassed 1.8 and 1.32, 1/33 prescaler from oscillator, at this mode. (Fosc 4 MHz)
10
11
APPLICATION INFORMATION
C21 R1 C50 C3 VC1 L1 R2 C6 L2 L3 C11 VC3 L4 R33 R32 C13 IF OUT1 C14 C16 IF OUT2 C17 R8 C65 C20 C24 R9 C22 C24 C75 X1 16 XTAL SCL C18 R7 C12 VC2 C4 C5 C7 C8 C9 C10 C1 C2 C38 URF C37 C70
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
VOL OSC B VOL OSC C OSC GND VHI OSC B VHI OSC C UHF OSC B1 UHF OSC C1 UHF OSC C2 UHF OSC B2 IF GND IF OUT1 IF OUT2 VCC CP VTU
UHF RF IN2 UHF RF VHF RF IN2 VHF RF IN1 RF GND MIX OUT2 MIX OUT1 BS4 BS3 BS2 BS1 NC ADC AS SDA
32 31 30
VRF
R3
TU
VCC
NOTE 8: This application information is advisory and performance-check is required at actual application circuits.
12
13
DUT
Noise Source
DUT
14
VHF-Input
UHF-Input
Figure 17
IF-Output
Figure 18
Figure 19
15
TYPICAL CHARACTERISTICS
SUPPLY VOLTAGE vs BS CURRENT
5 VCC = 5.5 V VSS Supply Voltage V 4 VCC = 5.0 V VCC = 4.5 V 3
8 10 12 14 16 18 20
16
MECHANICAL DATA
DA (R-PDSO-G**)
38 PINS SHOWN 0,30 0,19 20
PLASTIC SMALL-OUTLINE
0,65 38
0,13 M
6,20 NOM
30
32
38
11,10
11,10
12,60
A MIN
10,90
10,90
NOTES: A. B. C. D.
All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion. Falls within JEDEC MO-153
17
IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its products to the specifications applicable at the time of sale in accordance with TIs standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. Customers are responsible for their applications using TI components. In order to minimize risks associated with the customers applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such products or services might be or are used. TIs publication of information regarding any third partys products or services does not constitute TIs approval, license, warranty or endorsement thereof. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations and notices. Representation or reproduction of this information with alteration voids all warranties provided for an associated TI product or service, is an unfair and deceptive business practice, and TI is not responsible nor liable for any such use. Resale of TIs products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service, is an unfair and deceptive business practice, and TI is not responsible nor liable for any such use. Also see: Standard Terms and Conditions of Sale for Semiconductor Products. www.ti.com/sc/docs/stdterms.htm
Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265