Professional Documents
Culture Documents
13 August 2013
Commercial in Confidential
Page 1 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
Contents
1 OVERVIEW ....................................................................................................4
1.1 Introduction .....................................................................................................................................4 1.2 Reference Documents.......................................................................................................................4
2 EQUIPMENT LIST..........................................................................................5
2.1 Equipments under test.....................................................................................................................5 2.2 Instruments for testing....................................................................................................................5
13 August 2013
Commercial in Confidential
Page 2 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
5.4.3.2 DM Test..............................................................................................................................59 5.4.3.3 FDV Test............................................................................................................................62 5.5 1+1 HSB and 2+0 Scenario Test....................................................................................................63 5.5.1 1+1 HSB Scenario Test.............................................................................................................63 5.5.2 2+0 Scenario Test......................................................................................................................66
13 August 2013
Commercial in Confidential
Page 3 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
1
1.1
OVERVIEW
Introduction
This document describes the field test proposal used by Huawei microwave radio transmission platform RTN 300 series. The field trial information and microwave planning parameters are descripting in this document, and most contents of them should be completed after meeting with costumers. Every test case in this document can be applied to one or more field trial, and every field trial may implement with one or more test case. Chapter 4 descript the combination of radio link and test case.
1.2
Reference Documents
< RTN 380 V100R001 Feature Description > < RTN 380 V100R001 Configuration Guide > < RTN 380 V100R001 Maintenance Guide >
13 August 2013
Commercial in Confidential
Page 4 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
2
2.1
RTN380 U2000
EQUIPMENT LIST
Equipments under test
Products
Version
V1R1 V1R8C00 V1R8C00 V1R3/R5
Quantity
2 1 1 2
2.2
Quantity 1
13 August 2013
Commercial in Confidential
Page 5 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
3
3.1
Radio link
13 August 2013
Commercial in Confidential
Page 6 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
4
4.1
No 1 2 1+0 1+1
13 August 2013
Commercial in Confidential
Page 7 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
5
5.1
Test Consideration
Test Bench
1. Create radio link with required parameters. 2. Configure E-LINE services over radio link. Test Procedure 3. Loopback relevant Ethernet ports on remote site. 4. Configure the test analyzer with difference frames:96,101,512,1024,1518,1522. 5. Check the results. Test Results Radio link information: link 1 Radio Channel Spacing: 500MHz Packet length 96 Bytes Modulation Scheme: 64QAM Rate measured value
13 August 2013
Commercial in Confidential
Page 8 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
101 Bytes
512 Byte
1024 Bytes
1518 Bytes
13 August 2013
Commercial in Confidential
Page 9 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
1522 Bytes
Remarks: signature
5.2
Test Consideration
This case to verify that same basic parameters can be query and configurable by LCT in field. Be careful, some operations in this case may interrupt the radio link.
Test Bench
Test Procedure
13 August 2013
Commercial in Confidential
Page 10 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
2. Query the Radio configuration on LCT and check parameters list below are correct: a. Channel space b. Manually specified modulation c. Link ID
d. Received link id 3. Apply a new channel space and query the channel space should be update. ( before do this, you must ensure the adjacent channel is free) 4. Check the radio link is broken, then configure the channel space to initial value and check the radio link should restore. 5. Apply a new modulation scheme and query the modulation should be update. 6. Check the radio link is broken, then configure the modulation to initial and check the radio link should restore. 7. Apply a new Link ID and check the received link id on remote site should equal to this new ID. 8. Configure the Link ID to initial value and check the received link id on remote site should change back.
Radio link information: link 1 Radio Channel Spacing: 500MHz Actions Query the channel space Test Results Query the modulation scheme Query the Link ID Query the received Link ID Modify the channel space Modify the modulation scheme Modify the Link ID Reason for Failure: Remarks: Radio link ID Modulation Scheme: 16QAM Results OK OK OK OK OK OK OK
13 August 2013
Commercial in Confidential
Page 11 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
IF Channel:
13 August 2013
Commercial in Confidential
Page 12 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
Modulation mode:
signature
5.2.2
Test Consideration
Radio configuration
When a new radio link to be installing, the MW engineer should go to the site and configure radio parameters according to the network planning profile. This case to verify that same basic radio parameters can be query and configurable by LCT in field. Be careful, some operations in this case may interrupt the radio link.
Test Bench
Test
13 August 2013
Commercial in Confidential
Page 13 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
2. Query the raido configuration on LCT and check parameters below are correct: a. Actual transmit frequency b. Actual receive frequency c. Actual transmit power
d. Actual receive power e. Actual transmit status 3. Configure a new transmit frequency and query the actual value should be update to the new frequency. ( before do this, you must ensure this new frequency is free and no any other radio using this frequency on the same path) Procedure 4. Check the radio link is broken, then configure the transmit frequency to the initial value and check the radio link should restore. 5. Configure a new transmit power and query the actual value should be update to the new level 6. Check the receive power on remote site is changed, then configure the transmit power to the initial level and check the receive power on remote site is change back to the initial level. 7. Mute the radio and query the actual transmit status is mute, check the radio link will interrupt. 8. Unmute the radio and query the actual transmit status is mute, check the radio link will restore.
Radio link information: link 1 Radio Channel Spacing: 500MHz Actions Query the actual transmit frequency Test Results Query the actual receive frequency Query the actual transmit power Query the actual receive power Modify the transmit frequency Modify the transmit power Mute the radio Unmute the radio Reason for Failure: Remarks: TX frequency: Modulation Scheme: 64QAM Results Ok Ok Ok Ok Ok Ok Ok Ok
13 August 2013
Commercial in Confidential
Page 14 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
TX power:
RX power:
TX mute:
signature
13 August 2013
Commercial in Confidential
Page 15 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
5.3
5.3.1
5.3.1.1
Test Consideration
Test Bench
1. Establish a radio link with required parameters. 2. Configure an E-Line service with null source VLAN and sink VLAN. Test Procedure 3. Create an IP streams on Ethernet analyzer with or without VLAN. 4. Configure the transmit rate less than the throughput in current radio mode. 5. Start transmit, check received packets without any loss.
Radio link information: link 1 Test Results Radio Channel Spacing: 500MHz Ethernet Services IP Stream without VLAN IP Stream with VLAN Reason for Failure: Remarks: Modulation Scheme: 16QAM Result Pass through Pass through
13 August 2013
Commercial in Confidential
Page 16 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
Configuration:
13 August 2013
Commercial in Confidential
Page 17 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
13 August 2013
Commercial in Confidential
Page 18 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
Result :
13 August 2013
Commercial in Confidential
Page 19 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
signature
5.3.1.2
Test Consideration
Test Bench
Test Procedure
1. Establish a radio link with required parameters. 2. Loopback relevant ports on remote site.
13 August 2013
Commercial in Confidential
Page 20 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
3. Configure an E-Line service from port 1 of local site to port 1 of remote site through radio link with Vlan ID equal to 100. 4. Create an IP streams on the analyzers port which connect to port 1 of local site with VLAN id equal to 100200. 5. Start transmits with appropriate rate, check received packets on port 1.
Service Model:
Service 1 can pass through the radio link. And service 2 should be blocked.
Radio link information: link 1 Test Results Radio Channel Spacing: 500MHz Ethernet Services IP service 1 (Vlan id: 100) IP service 2 (Vlan id: 200) Reason for Failure: Remarks: Configuration: Modulation Scheme: 256QAM Result Pass block
13 August 2013
Commercial in Confidential
Page 21 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
13 August 2013
Commercial in Confidential
Page 22 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
13 August 2013
Commercial in Confidential
Page 23 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
signature
5.3.2
5.3.2.1
Test Consideration
Test Bench
1. Create radio link with required parameters. Test Procedure 2. Configure E-LINE services over radio link. 3. Loopback relevant Ethernet ports on remote site. 4. Measure the latency with required packet length.
Radio link information: link 1 Radio Channel Spacing: 500MHz Test Results Packet length 64 Bytes 128 Bytes Modulation Scheme: 64QAM Round-trip delay Notes in remarks Notes in remarks Notes in remarks
13 August 2013
Commercial in Confidential
Page 24 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
Expected Results
Result :
Remarks:
signature
5.3.3
5.3.3.1
Test Consideration
13 August 2013
Commercial in Confidential
Page 25 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
Test Bench
1. Create radio link with required parameters. Test Procedure 2. Configure E-LINE services over radio link. 3. Loopback relevant Ethernet ports on remote site. 4. Measure the throughput with 64bits packet length on the highest modulation. Test Results Reason for Failure: Throughput : The maximum radio transmission capacity can reach 2.490Gbps
Remarks:
signature
13 August 2013
Commercial in Confidential
Page 26 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
5.3.3.2
Test Consideration
Test Bench
6. Create radio link with required parameters. Test Procedure 7. Configure E-LINE services over radio link. 8. Loopback relevant Ethernet ports on remote site. 9. Measure the throughput with required packet length.
Radio link information: link 1 Radio Channel Spacing: 500MHz Test Results Packet length 64 Bytes 128 Bytes Expected Results Modulation Scheme: 64QAM Throughput measured value More than 1G More than 1G More than 1G
13 August 2013
Commercial in Confidential
Page 27 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
Remarks:
13 August 2013
Commercial in Confidential
Page 28 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
13 August 2013
Commercial in Confidential
Page 29 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
signature
5.3.4
5.3.4.1
Test Consideration
This case to verify schedule the Ethernet services according to VLAN priority in RTN equipment. In this test case, we are considering three kinds of condition to verify this feature, the first one is a basic scenario that without congestion, the second one is got congestion and restore in case of the transmission rate change of one or more services changing, the last one is got congestion and restore in case of radio transmission capacity change (e.g. AM down shift and up shift).
13 August 2013
Commercial in Confidential
Page 30 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
Test Bench
Service Model:
Test Procedure
1. Establish a radio link with required parameters. 2. Connecting the GE port of Ethernet analyzer to NE. 3. Configure an E-Line service with VLAN ID 100 between local and remote sites. 4. Loopback the service port on remote site. 5. Create a new port policy with required schedule policy (e.g. ALL queues are SP). 6. Configure traffic classification according to the VLAN priority and map them to different queues. 7. Apply the policy to relevant ports. 8. Create 4 IP streams on the test port of Ethernet analyzer with same VLAN ID and with different VLAN priority. Condition 1 : 1. Setting the transmit rate for every stream and keep the amount transmit rate is less than radio transmission capacity. 2. Start transmit all services, check the actual received rate of every stream is equal to the transmit rate, that means all services are transmit through the radio link correctly. Condition 2: 1. Increase the transmit rate of stream1till the radio getting congestion. 2. The low priority should be lost. 3. Restore the transmit rate of stream 1. 4. Start transmit all services, check the actual received rate of every test port is
13 August 2013
Commercial in Confidential
Page 31 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
equal to the transmit rate, that means all services are transmit through the radio link correctly.
Radio link information: link 1 Radio Channel Spacing: 500MHz IP streams configuration: Stream1: 128byte, Vlan ID 100, VLAN Pri 7, Stream2: 128byte, Vlan ID 100, VLAN Pri 5, Stream3: 128byte, Vlan ID 100, VLAN Pri 3, Stream4: 128byte, Vlan ID 100, VLAN Pri 1, Condition 1: Non-Congestion Ethernet Services Test Results Stream1 Stream2 Stream3 Stream4 AMOUNT Actual Transmitting Rate 100M 100M 100M 100M 400M Actual Receiving Rate 100M 100M 100M 100M 400M Modulation Scheme: QPSKS
Condition 2: Congestion by transmission rate of streams increased Ethernet Services Stream1 Stream2 Stream3 Stream4 AMOUNT Expected Results Remarks: Configuration : The packet losing of each service is correct by different VLAN priority. Actual Transmitting Rate (Congestion / Restore) 250/350/424 100 100 100 Actual Receiving Rate (Congestion / Restore) 250/350/424 100/74/0 74/0/0 0/0/0
13 August 2013
Commercial in Confidential
Page 32 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
13 August 2013
Commercial in Confidential
Page 33 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
13 August 2013
Commercial in Confidential
Page 34 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
signature signature
5.3.5
5.3.5.1
Service Stability
Ethernet service transmission stability test
This case to verify the reliability of Ethernet service that transmits through radio link for a long test period.
Test Consideration
13 August 2013
Commercial in Confidential
Page 35 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
Test Bench
1. Establish a radio link with required parameters. Test Procedure 2. Configure Ethernet service. 3. Make PER measurement for a period of more than 24 hrs.
Radio link information: link 1 Radio Channel Spacing: 500MHz Test Results Service Type
Ethernet Stream1
Service Description
Packets length: 101 Throughput: 2G Vlan-ID: 100 Priority: 0
Stop Date/Time
2013-02-09
Results
OK
13 August 2013
Commercial in Confidential
Page 36 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
signature
5.4
5.4.1
5.4.1.1
Test Consideration
Test Bench
Test Procedure
1. In NE List, query communication status of an NE, communication status needs to be Normal. 2. Check Login Status of an NE. If the Login Status column of an NE is Not Logged In, log in to the NE. a) Select an NE, and then click NE Login, the NE Login dialog box is
13 August 2013
Commercial in Confidential
Page 37 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
displayed. b) Enter a user name in User Name and a password in Password. c) The user name is lct by default. The password for the user lct is Changeme_123 by default.
Click OK. After you log in to the NE successfully, Login Status in NE List changes to Logged In.
Radio link information: Radio link 1 Test Results Actions NE login Login status after login Reason for Failure: Remarks: OK OK Results
13 August 2013
Commercial in Confidential
Page 38 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
13 August 2013
Commercial in Confidential
Page 39 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
signature
5.4.1.2
Test Consideration
13 August 2013
Commercial in Confidential
Page 40 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
Test Bench
1. In the NE Explorer, select the required NE from the Object Tree, and then click the icon on the toolbar. You can also click an alarm indicator on the toolbar to display the alarms of the specific severity. From left to right, the alarm indicators and corresponding alarm severities are as follows: Red: critical alarm Test Procedure Orange: major alarm Yellow: minor alarm Purple: warning Light blue: abnormal event 2. Browse the displayed alarms. 3. If there are newly generated alarms after the last maintenance, select the newly generated alarms, record the details of these newly generated alarms, and then notify the troubleshooting personnel to clear these alarms in time. 4. Click Save As, a text file that lists the current alarms is displayed in Internet Explorer.
Radio link information: Radio link 1 Radio Channel Spacing: 500MHz Test Results Actions Browsing the Current alarms Save the Current alarms to a file Plaster the current alarms file in here. Reason for Failure: Ok Ok Modulation Scheme: 16QAM Results
13 August 2013
Commercial in Confidential
Page 41 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
Remarks:
signature
13 August 2013
Commercial in Confidential
Page 42 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
5.4.1.3
Test Consideration
Test Bench
1. In the NE Explorer, select the required NE from the Object Tree, and then click the icon on the toolbar.
2. Click the Browse History Alarms tab. 3. Click Filter, The Filter dialog box is displayed. Test Procedure 4. Specify Rising Time and Cleared Time, and then click Filter. 5. The time span starts from the time when the last history alarm browsing operation was performed to the current time. 6. Browse the filtered history alarms. 7. Click Save As, a text file that lists the history alarms is displayed in Internet Explorer.
Radio link information: Radio link 1 Test Results Radio Channel Spacing: 500MHz Actions Browsing the History alarms Save the History alarms to a file Reason for Failure: Remarks: OK OK Modulation Scheme: 16QAM Results
13 August 2013
Commercial in Confidential
Page 43 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
13 August 2013
Commercial in Confidential
Page 44 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
13 August 2013
Commercial in Confidential
Page 45 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
signature
5.4.1.4
Test Consideration
Test Bench
1. GO to the main topology, press the radio link and select the radio link monitor. Test Procedure 2. Choose the 15min or 24h performance, and query valve. 3. Check the curve of the TX power and RX power.
Radio link information: Radio link 1 Test Results Radio Channel Spacing: 500MHz Actions Browsing the transmit power Browsing the receive power Reason for Failure: Remarks: OK OK Modulation Scheme: 64QAM Results
13 August 2013
Commercial in Confidential
Page 46 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
13 August 2013
Commercial in Confidential
Page 47 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
signature
5.4.2
5.4.2.1
Emergency Maintenance
IEEE 802.1ag ETH OAM test
The IEEE 802.1ag OAM focuses on the maintenance of end-to-end Ethernet links. It realizes the sectional and segmental management over the service flow by specifying the maintenance domain, maintenance association, and maintenance point.
Test Consideration
Test Bench
Test Procedure
1. Create radio link with required parameters. 2. Creating a maintenance domain (MD). 3. Creating a maintenance association (MA). 4. Creating an MEP point. 5. Creating remote MEPs in an MA. 6. Creating MIP. 7. Performing LB and LT testing on local site.
13 August 2013
Commercial in Confidential
Page 48 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
Radio link information: Radio link 1 Test Results Radio Channel Spacing: 500MHz Actions LB test for a good radio link LT test for a good radio link Reason for Failure: Remarks: Modulation Scheme: 64QAM Results pass pass
13 August 2013
Commercial in Confidential
Page 49 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
13 August 2013
Commercial in Confidential
Page 50 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
13 August 2013
Commercial in Confidential
Page 51 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
13 August 2013
Commercial in Confidential
Page 52 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
13 August 2013
Commercial in Confidential
Page 53 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
13 August 2013
Commercial in Confidential
Page 54 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
13 August 2013
Commercial in Confidential
Page 55 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
signature
13 August 2013
Commercial in Confidential
Page 56 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
5.4.3
5.4.3.1
Test Purpose
Y1731 Test
LM Test
Test the Ethernet OAM function.
Test Topology
(1) Setup the configuration according above figure.. (2) Configure Ethernet service from NE1 to NE2. Test Steps (3) Create MEP1 at port of NE1, and set the MPID (4) Create MEP2 at port of NE2, and set the MPID, (5) Set the frame loss test parameters and check the result. Expected Results Pass / Fail Remarks Frame loss test work normally and the result is the same with the tester. pass
13 August 2013
Commercial in Confidential
Page 57 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
13 August 2013
Commercial in Confidential
Page 58 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
Signature
5.4.3.2
DM Test
Test the Ethernet OAM function.
Test Purpose
13 August 2013
Commercial in Confidential
Page 59 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
Test Topology
(1) Setup the configuration according above figure.. (2) Configure Ethernet service from NE1 to NE2. Test Steps (3) Create MEP1 at port of NE1, and set the MPID (4) Create MEP2 at port of NE2, and set the MPID, (5) Set the frame delay test parameters and check the result. Expected Results Pass / Fail Frame delay test work normally and the result is the same with the tester . Latency: 70us----150us one way pass
Remarks
13 August 2013
Commercial in Confidential
Page 60 of 68
Huawei Microwave Radio Product RTN 900 V100R003 Test Proposal V1.0
Signature
13 August 2013
Commercial in Confidential
Page 61 of 68
5.4.3.3
FDV Test
Test the Ethernet OAM function.
Test Purpose
Test Topology
(6) Setup the configuration according above figure.. (7) Configure Ethernet service from NE1 to NE2. Test Steps (8) Create MEP1 at port of NE1, and set the MPID (9) Create MEP2 at port of NE2, and set the MPID, (10)Set the frame delay test parameters and check the result. Expected Results Pass / Fail Frame delay test work normally and the result is the same with the tester. Less than 10us. pass
Remarks
13 August 2013 68
Commercial in Confidential
Page
62 of
5.5
Test Purpose
Test Topology
(1) Create the test environment as shown in the diagram above. (2) Configure 1+1 HSB on the RTN 380, RTN380 NE1 is main unite, NE2 is standby. And RTN380 NE3 is main unite,NE4 is standby. (3) Configure Two Ethernet service between NE1 and NE3 with vlan 100 and the vlan 200. (4) Setting the Ethernet analyzer, send traffic with vlan 100, and vlan 200. (5) Check the service status. (6) Cut off the main radio link, the service should be switch to the standby.
Test Steps
Remarks:
This scenario requires the switch or the upper device support static nonsharing mode. If the switch can support the LAG configuration, the HSB will work normally. But in current test environment, the switch can not support non-sharing mode, so another solution have to be used to instead. Solution 2: Configure ports protection on switch side. This solution switching time is more than 3s. Test topology:
Commercial in Confidential Page
63 of
13 August 2013 68
Before switching
After switching
13 August 2013 68
Commercial in Confidential
Page
64 of
So for one link, it can transmit 1Gbps service and for each port is 500Mbps
Signature
13 August 2013 68
Commercial in Confidential
Page
65 of
5.5.2
Test Purpose
Test Topology
(1) Create the test environment as shown in the diagram above; (2) Configure Manual Sharing LAG on switch side; (3) Configure four Ethernet service between NE1 and NE3 with vlan 100, 200, 300, and 400. (4) Connect the switch and the tester with 10G port and set the Ethernet analyzer, send Eth traffic. (5) Check the service status.
Test Steps
Remarks:
This scenario requires the switch or the upper device support manual sharing mode. If the switch can support the LAG configuration, the 2+0 will work normally. In current test environment, the switch can not support banding one optical and electoral ports in one sharing LAG, so we test another solution. Test topology:
Commercial in Confidential Page
66 of
13 August 2013 68
Link 1 channel bandwidth and modulation is 500MHz16QAM ,capacity is 1.3Gb. And the RX power is -51dBm and -47dBm. Link 2 channel bandwidth and modulation is 500MHz16QAM,capacity is 1.3GB. And the Rx power is -58dBm and -56dBm So for 2+0 scenario, 2Gbps service can be transmitted and each port 500Mbps
13 August 2013 68
Commercial in Confidential
Page
67 of
Signature
13 August 2013 68
Commercial in Confidential
Page
68 of