You are on page 1of 216

OWNERS MANUAL

Thank you, and congratulations on your choice of the Roland XP-30 64 Voice Expandable Synthesizer.

Before using this unit, carefully read the sections entitled: IMPORTANT SAFETY INSTRUCTIONS (p. 2), USING THE UNIT SAFELY (p. 3), and IMPORTANT NOTES (p. 5). These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owners manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference.

* * * * *

Apple is a registered trademark of Apple Computer, Inc. Macintosh is a registered trademark of Apple Computer, Inc. IBM is a registered trademark of International Business Machines Corporation. IBM PC is a registered trademark of International Business Machines Corporation. SmartMedia is a trademark of Toshiba Corporation.

Copyright 1999 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.

CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN

ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR


CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS.

IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS


WARNING - When using electric products, basic precautions should always be followed, including the following: 1. 2. 3. 4. 5. 6. 7. 8. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block any of the ventilation openings. Install in accordance with the manufacturers instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Never use with a cart, stand, tripod, bracket, or table except as specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

9.

For the U.K. IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE. BLUE: NEUTRAL BROWN: LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Under no circumstances must either of the above wires be connected to the earth terminal of a three pin plug.

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with same or equivalent type.

Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly. Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly. * Material damage refers other adverse effects respect to the home furnishings, as well animals or pets. to damage or caused with and all its to domestic

The symbol alerts the user to important instructions or warnings.The specific meaning of the symbol is determined by the design contained within the triangle. In the case of the symbol at left, it is used for general cautions, warnings, or alerts to danger. The symbol alerts the user to items that must never be carried out (are forbidden). The specific thing that must not be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the unit must never be disassembled. The symbol alerts the user to things that must be carried out. The specific thing that must be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the powercord plug must be unplugged from the outlet.

001 Before using this unit, make sure to read the instructions below, and the Owners Manual. .......................................................................................................... 002b Do not open or perform any internal modifications on the unit. (The only exception would be where this manual provides specific instructions which should be followed in order to put in place userinstallable options; see p. 17, 21.) .......................................................................................................... 006 When using the unit with a rack or stand recommended by Roland, the rack or stand must be carefully placed so it is level and sure to remain stable. If not using a rack or stand, you still need to make sure that any location you choose for placing the unit provides a level surface that will properly support the unit, and keep it from wobbling. .......................................................................................................... 008e Use only the attached power-supply cord. .......................................................................................................... 009 Avoid damaging the power cord. Do not bend it excessively, step on it, place heavy objects on it, etc. A damaged cord can easily become a shock or fire hazard. Never use a power cord after it has been damaged. .......................................................................................................... 013 In households with small children, an adult should provide supervision until the child is capable of following all the rules essential for the safe operation of the unit. .......................................................................................................... 014 Protect the unit from strong impact. (Do not drop it!) ..........................................................................................................

015 Do not force the units power-supply cord to share an outlet with an unreasonable number of other devices. Be especially careful when using extension cordsthe total power used by all devices you have connected to the extension cords outlet must never exceed the power rating (watts/ amperes) for the extension cord. Excessive loads can cause the insulation on the cord to heat up and eventually melt through. .......................................................................................................... 016 Before using the unit in a foreign country, consult with your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the Information page. .......................................................................................................... 022a Always turn the unit off and unplug the power cord before attempting installation of the circuit board (SR-JV80 series). .......................................................................................................... 023 DO NOT play a CD-ROM disc on a conventional audio CD player. The resulting sound may be of a level that could cause permanent hearing loss. Damage to speakers or other system components may result. ..........................................................................................................

USING THE UNIT SAFELY

102b Always grasp only the plug on the power-supply cord when plugging into, or unplugging from, an outlet or this unit. .......................................................................................................... 104 Try to prevent cords and cables from becoming entangled. Also, all cords and cables should be placed so they are out of the reach of children. .......................................................................................................... 106 Never climb on top of, nor place heavy objects on the unit. .......................................................................................................... 107b Never handle the power cord or its plugs with wet hands when plugging into, or unplugging from, an outlet or this unit. .......................................................................................................... 108a Before moving the unit, disconnect the power plug from the outlet, and pull out all cords from external devices. .......................................................................................................... 109a Before cleaning the unit, turn off the power and unplug the power cord from the outlet. .......................................................................................................... 110a Whenever you suspect the possibility of lightning in your area, pull the plug on the power cord out of the outlet. .......................................................................................................... 115a Install only the specified circuit board(s) (SR-JV80 series). Remove only the specified screws (p. 17, 21). ..........................................................................................................

Important Notes
In addition to the items listed under IMPORTANT SAFETY INSTRUCTIONS and USING THE UNIT SAFELY on pages 2 and 3, please read and observe the following:

Additional Precautions
Please be aware that the contents of memory can be irretrievably lost as a result of a malfunction, or the improper operation of the unit. To protect yourself against the risk of loosing important data, we recommend that you periodically save a backup copy of important data you have stored in the units memory on a memory card. Unfortunately, it may be impossible to restore the contents of data that was stored in the units memory, a memory card or another MIDI device (e.g., a sequencer) once it has been lost. Roland Corporation assumes no liability concerning such loss of data. Use a reasonable amount of care when using the units buttons, sliders, or other controls; and when using its jacks and connectors. Rough handling can lead to malfunctions. Never strike or apply strong pressure to the display. When connecting / disconnecting all cables, grasp the connector itselfnever pull on the cable. This way you will avoid causing shorts, or damage to the cables internal elements. A small amount of heat will radiate from the unit during normal operation. To avoid disturbing your neighbors, try to keep the units volume at reasonable levels. You may prefer to use headphones, so you do not need to be concerned about those around you (especially when it is late at night). When you need to transport the unit, package it in the box (including padding) that it came in, if possible. Otherwise, you will need to use equivalent packaging materials. Use only the specified expression pedal (EV-5; sold separately). By connecting any other expression pedals, you risk causing malfunction and/or damage to the unit.

Power Supply
Do not use this unit on the same power circuit with any device that will generate line noise (such as an electric motor or variable lighting system). Before connecting this unit to other devices, turn off the power to all units. This will help prevent malfunctions and/or damage to speakers or other devices.

Placement
Using the unit near power amplifiers (or other equipment containing large power transformers) may induce hum. To alleviate the problem, change the orientation of this unit; or move it farther away from the source of interference. This device may interfere with radio and television reception. Do not use this device in the vicinity of such receivers. Do not expose the unit to direct sunlight, place it near devices that radiate heat, leave it inside an enclosed vehicle, or otherwise subject it to temperature extremes. Excessive heat can deform or discolor the unit. To avoid possible breakdown, do not use the unit in a wet area, such as an area exposed to rain or other moisture.

Maintenance
For everyday cleaning wipe the unit with a soft, dry cloth or one that has been slightly dampened with water. To remove stubborn dirt, use a cloth impregnated with a mild, non-abrasive detergent. Afterwards, be sure to wipe the unit thoroughly with a soft, dry cloth. Never use benzine, thinners, alcohol or solvents of any kind, to avoid the possibility of discoloration and/or deformation.

Before Using Memory Cards


Using Memory Cards
Carefully insert the Memory card all the way inuntil it is firmly in place.

Repairs and Data


Please be aware that all data contained in the units memory may be lost when the unit is sent for repairs. Important data should always be backed up memory card, or written down on paper (when possible). During repairs, due care is taken to avoid the loss of data. However, in certain cases (such as when circuitry related to memory itself is out of order), we regret that it may not be possible to restore the data, and Roland assumes no liability concerning such loss of data.

Memory Backup
This unit contains a battery which powers the units memory circuits while the main power is off. When this battery becomes weak, the message shown below will appear in the display. Once you see this message, have the battery replaced with a fresh one as soon as possible to avoid the loss of all data in memory. To have the battery replaced, consult with your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the Information page. Battery Low Never touch the terminals of the Memory card. Also, avoid getting the terminals dirty.

Handling CD-ROMs
Avoid touching or scratching the shiny underside (encoded surface) of the disc. Damaged or dirty CD-ROM discs may not be read properly. Keep your discs clean using a commercially available CD cleaner.

How to Read This Owners Manual


This owners manual is organized as follows.

Quick Start
This section is intended for those using the XP-30 for the first time, and explains how to use various functions in a simple way. Please read Quick Start and follow along by actually operating the XP-30. This will help you understand most of what you need to know for basic operations. More advanced ways of using the XP-30 or details of other operations are explained the Advanced Use section.

Chapter 6. Getting the Full Potential of the XP-30


This chapter includes various techniques that expand the XP30s operational scope. It includes use with external MIDI devices, live performance applications and others.

Appendices
This chapter contains a troubleshooting section for use when the XP-30 is not functioning as expected. There is also a list of error messages that you can refer to if an error message appears on the display. A list of parameters and MIDI implementation chart are also provided.

Advanced Use
The Advanced Use section is divided into 6 chapters. But before you start reading it, wed like to suggest going through the Quick Start section.

Chapter 1. Overview of the XP-30


This chapter covers XP-30 sound source section configurations, as well as basic operation. Please be sure to read this chapter in order to fully understand the XP-30.

s Notation Used in This Owners Manual


To make operation procedures easy to understand, the following notation system is adopted: Characters and numbers in square brackets [ ] indicate buttons on the front panel. For example, [PATCH] represents the PATCH button and [ENTER] the ENTER button. An asterisk (*) at the beginning of a paragraph indicates a note or precaution. These should not be ignored. In the Quick Start section, such material is indicated by ( ). (p. **) refers to pages within the manual. In this manual, when any particular parameter is referred to, the name of the parameter is given, and this is then followed (in parenthesis) by information detailing its mode, display group, and display. For example: Key Mode parameter (PERFORM/COMMON/PERFORM COMMON). * The display screens printed in this owners manual are based on the factory settings. However, please be aware that in some cases they may differ from the actual factory settings.

Chapter 2. Playing
This chapter explains how to use the XP-30 in Patch, Performance and Rhythm Set modes. Reading it is essential for understanding XP-30 operational procedures.

Chapter 3. Creating Your Own Sounds


This chapter covers creating sounds, the parameters that make up a Patch, Performance, or Rhythm Set, and the System parameters that determine global XP-30 operation, as well as their functions. Comprehending the information in the chapter is an essential prerequisite before creating your own sounds.

Chapter 4. Memory Settings (Utility/Card Mode)


This chapter goes over the various Utility functions such as storing Patch, Performance or Rhythm Set data, clearing the internal memory, etc. Being familiar with these will streamline operation procedures.

Chapter 5. Using the XP-30 as the GM Sound Module


This chapter explains needed procedures and parameters for using the XP-30 as a General MIDI System-compatible sound source. Read this chapter before attempting to play back commercial General MIDI System score data.

Contents
Main Features........................................................................................11 Front and Rear Panel............................................................................12

Quick Start ........................................................ 15


Getting Ready........................................................................................16
Installing the Wave Expansion Board ................................................................................................... 16 Cautions When Installing an Wave Expansion Board............................................................. 16 Installation de la carte dextension Wave (French language for Canadian Safety Standard) ....... 20 Precautions lors de linstallation de la carte dextension Wave ............................................. 20 Making Connections ................................................................................................................................ 24 Turning On the Power ............................................................................................................................. 26 Turning Off the Power ................................................................................................................. 26 Reset to Default Factory Settings (Factory Reset) ................................................................................ 27

Listening to the Demo Song ................................................................28


Profile of the Composer ............................................................................................................... 29

Playing the Sounds...............................................................................30


Selecting Patches and Playing the Sounds............................................................................................ 30 Selecting Wave Expansion Patches........................................................................................................ 31 Selecting Patches by Category (Patch Search Function) ..................................................................... 32 Auditioning the Patches (Phrase Preview) ........................................................................................... 33 Try Out Performance Functions............................................................................................................. 34 Velocity/Aftertouch ..................................................................................................................... 34 Pitch Bend/Modulation Lever .................................................................................................... 34 C1C4 Slider................................................................................................................................... 34 Hold Pedal...................................................................................................................................... 35 Expression Pedal ........................................................................................................................... 35 Solo .................................................................................................................................................. 35 Portamento..................................................................................................................................... 35 Sound Palette ................................................................................................................................. 36 Play Arpeggios (Arpeggiator) ................................................................................................................ 36 Play Percussion Sounds from the Keyboard ........................................................................................ 38

Advanced Use ................................................... 39


Chapter 1. Overview of the XP-30........................................................40
XP-30 Configuration................................................................................................................................. 40 Basic Configuration....................................................................................................................... 40 Classification of XP-30 Sound Types.......................................................................................... 40 Number of Simultaneous Voices ................................................................................................ 42 Basic Operation......................................................................................................................................... 42 Switching Modes........................................................................................................................... 42 About the Function Buttons ........................................................................................................ 43 About the Cursor Buttons............................................................................................................ 44 Modifying a Value ........................................................................................................................ 45 Assigning a Name ......................................................................................................................... 46

Contents

Chapter 2. Playing.................................................................................47
Playing in Patch Mode............................................................................................................................. 47 Selecting a Patch ............................................................................................................................ 47 Using Phrase Preview to Play Patches....................................................................................... 49 Making a Patch Sound Thick or Thin (Turning a Tone On/Off) ........................................... 50 Playing Single Notes (Solo) ......................................................................................................... 50 Creating Smooth Pitch Changes (Portamento) ......................................................................... 50 Using the Sliders to Modify the Sound in Realtime (Sound Palette Function).................... 50 Playing in Performance Mode ................................................................................................................ 51 Selecting a Performance ............................................................................................................... 51 Playing Fatter and Richer Sounds by Combining Patches (Layer)........................................ 52 Splitting the Keyboard to Play Separate Patches in Different Sections (Split)..................... 52 Playing Along with a Song Playback (XP-30 Used as a Multitimbral Sound Source) ........ 53 Assigning a Different Patch to a Part ......................................................................................... 54 Using the Sliders to Modify the Sound in Realtime (Sound Palette Function).................... 54 Playing in Rhythm Set Mode .................................................................................................................. 55 Selecting a Rhythm Set ................................................................................................................. 55 Playing Percussion Instruments ................................................................................................. 56 Playing an Arpeggio ................................................................................................................................ 56 Playing an Arpeggio Over a Preset Keyboard Area ................................................................ 57 Holding an Arpeggio.................................................................................................................... 58 Simulating a Guitar Cutting Technique..................................................................................... 58 Playing an Arpeggio from an External MIDI Device............................................................... 58 Creating an Arpeggio Pattern ..................................................................................................... 58 Convenient Functions for Performance ................................................................................................ 59 Transposing the Keyboard in Octave Units (Octave Shift)..................................................... 59 Transposing the Keyboard in Semitone Steps (Transpose) .................................................... 60 If Stuck Notes Occur or a Note Does Not Sound (Panic) .................................................... 60

Chapter 3. Creating Your Own Sounds...............................................61


Regarding Effects...................................................................................................................................... 61 How Effects Units Work in Different Modes ............................................................................ 61 Turning Effects On/Off................................................................................................................ 62 Sound Editing Procedures....................................................................................................................... 62 Editing a Patch............................................................................................................................... 62 Editing a Performance .................................................................................................................. 65 Editing a Rhythm Set.................................................................................................................... 66 Keeping Edited Sound ............................................................................................................................. 67 Memory and Data Storage ........................................................................................................... 67 Storing a Sound You Modify into User Memory ..................................................................... 68 Functions of Patch Parameters ............................................................................................................... 68 Settings Common to the Entire Patch (COMMON)................................................................. 68 Setting Effects for a Patch (EFFECTS) ........................................................................................ 71 Using Controllers to Change How Sounds Are Played (CONTROL)................................... 73 Modifying Waveform (WAVE)................................................................................................... 76 Modulating Sounds (LFO) ........................................................................................................... 78 Modifying Pitch (PITCH)............................................................................................................. 79 Modifying the Brightness of Sound with a Filter (TVF).......................................................... 80 Changing the Sounds Volume and Stereo Location (TVA) ................................................... 81 Functions of Performance Parameters................................................................................................... 83 Settings Common to the Entire Performance (COMMON) .................................................... 83 Setting Effects for a Performance (EFFECTS) ........................................................................... 84 Making MIDI Settings for a Part (MIDI).................................................................................... 86 Making Settings for Each Part (PART)....................................................................................... 87 Confirming MIDI Information for Each Part (INFO) .............................................................. 87 Functions of Rhythm Set Parameters .................................................................................................... 88 Naming a Rhythm Set (COMMON)........................................................................................... 88

Contents

Setting Effects for a Rhythm Tone (EFFECTS).......................................................................... 88 Controlling How a Rhythm Tone will Sound with Controllers (CONTROL) ..................... 90 Modifying Waveform of a Rhythm Tone (WAVE) .................................................................. 90 Modifying Pitch of a Rhythm Tone (PITCH) ............................................................................ 91 Changing the Tone (Filter) of a Rhythm Tone (TVF)............................................................... 91 Changing the Volume and Stereo Location of a Rhythm Tone (TVA).................................. 92 Multi-Effects Types (EFX Parameter) .................................................................................................... 93 XP-30 Operating Environment Setup (System Parameters and Their Functions) ........................ 108 Display Screen Contrast and Clock Settings (SETUP)........................................................... 108 Arpeggio Settings (ARPEGGIO)............................................................................................... 108 Keyboard and Controllers Settings (CONTROL)................................................................... 110 MIDI Settings (MIDI).................................................................................................................. 112 Phrase Preview Settings (PREVIEW) ....................................................................................... 113 Adjusting Tuning (TUNE) ......................................................................................................... 113 Program Change (PGM CHNG) ............................................................................................... 114 Checking Things Such as the Installation Status of Wave Expansion Boards (INFO)...... 114

Chapter 4. Memory Settings (Utility/Card Mode) .............................115


About Utility/Card Mode..................................................................................................................... 115 Basic Procedure in Utility/Card Mode ............................................................................................... 115 Storing Sound Data in User Memory (WRITE).................................................................................. 116 Performance Write ...................................................................................................................... 116 Patch Write................................................................................................................................... 116 Rhythm Set Write ........................................................................................................................ 116 Copying Sound Source Settings (COPY) ............................................................................................ 117 Performance Copy ...................................................................................................................... 117 Patch Copy ................................................................................................................................... 117 Rhythm Set Copy ........................................................................................................................ 118 Initializing Sound Source Settings (INIT) ........................................................................................... 119 Performance Initialize................................................................................................................. 119 Patch Initialize ............................................................................................................................. 119 Rhythm Set Initialize .................................................................................................................. 119 Transmitting Sound Settings (XFER)................................................................................................... 119 Transmitting Data to an External MIDI Device...................................................................... 119 Transmitting Data to User Memory ......................................................................................... 120 Preventing User Memory Writing Operation (PROTECT) .............................................................. 121 Memory Card-Related Settings (CARD)............................................................................................. 121 Formatting the Memory Card for the XP-30 (FORMAT) ...................................................... 122 Renaming a File (RENAME)...................................................................................................... 122 Deleting Unwanted Files (DELETE)......................................................................................... 122 Checking the Contents Memory Card (INFO)........................................................................ 122 Loading a File from Memory Card into the XP-30 (LOAD)............................................................. 122 Saving Data to Memory Card (SAVE)................................................................................................. 122 Recalling Factory Default Settings (FACTORY RESET) ................................................................... 123

Chapter 5. Using the XP-30 as the GM Sound Module ....................124


Entering GM Mode................................................................................................................................. 124 Initializing the Sound Source for GM System Basic Settings ............................................... 124 Playing Back a GM Score ........................................................................................................... 124 Modifying GM Mode Settings .............................................................................................................. 125 Making Effects Settings in GM Mode (EFFECTS) .................................................................. 125 Setting a Part (PART).................................................................................................................. 127 Confirming MIDI Information of Each Part (INFO) .............................................................. 127 Convenient Functions in GM Mode (GM Utility) ............................................................................. 127 Copying Effects Settings (COPY).............................................................................................. 128 Initializing GM Mode (INIT) ..................................................................................................... 128 Transmitting GM Mode Settings (XFER)................................................................................. 128

Contents

Chapter 6. Getting the Full Potential of the XP-30 ...........................129


Techniques for Using Patches............................................................................................................... 129 Reinforcing Filter Characteristics ............................................................................................. 129 Making the Up-Beat Note Sound at the Same Time You Play a Down-Beat Note ........... 129 Holding a Note with Modulation Retained ............................................................................ 129 Syncing the LFO Cycle to System Tempo ............................................................................... 129 Modifying Multi-Effects to Match the Systems Tempo........................................................ 130 Using a Pedal Switch to Modify the Rotary Speed of the Rotary Effect ............................. 130 Playing Phrase Loops at a Systems Tempo............................................................................ 130 Using the Slider to Pan Sounds in Real Time ......................................................................... 131 Using the XP-30 to Play Live ................................................................................................................ 131 Changing Multiple Sounds of an External MIDI Device Simultaneously.......................... 131 Changing Sounds with a Pedal Switch .................................................................................... 131 Using External MIDI Devices ............................................................................................................... 132 Using the XP-30 to Control External MIDI Devices............................................................... 132 Playing the XP-30s Sound Source from an External MIDI Device ..................................... 132 Selecting XP-30 Sounds from an External MIDI Device........................................................ 132 Enjoying Desktop Music ....................................................................................................................... 134 Connecting to Your Computer.................................................................................................. 134 Disconnecting the Keyboard from the Internal Sound Source (Local OFF) ....................... 137

Appendices...................................................... 139
Troubleshooting..................................................................................140 Error Messages ...................................................................................142 Quick Reference of Procedures ........................................................143 Parameter List .....................................................................................147 Waveform List .....................................................................................160 Patch List.............................................................................................168 Rhythm Set List...................................................................................177 Performance List.................................................................................181 Arpeggio Style List .............................................................................182 MIDI Implementation...........................................................................183 Specifications......................................................................................207 Computer Cable Wiring Diagrams.....................................................208 Index.....................................................................................................209

10

Main Features
s High-Performance Synthesizer Sound Source
64-Voice Polyphony and 16-Part Multitimbrality
The XP-30 is a 16-part multitimbral sound source that produces up to 64 simultaneous polyphonic notes. Effectively used with an external sequencer or computer, the XP-30s true creative potential for music production becomes apparent (p. 41).

s Expandability
Allows Two Wave Expansion Boards to be Installed at the Same Time
Up to two SR-JV80 series Wave Expansion Boards can be installed simultaneously, allowing you to expand the range of available sounds (p. 16, 20).

Data from Popular Wave Expansion Boards Already Onboard


The data of the three popular Wave Expansion Boards, the SR-JV80-02 Orchestral, SR-JV80-09 Session, and SR-JV8011 Techno Collection is onboard. This means that for practical purposes, you can have simultaneous access to the sounds of up to five Wave Expansion Boards, and can draw on a vast quantity of waveform data as material for creating your sounds.

Powerful Onboard Effects


Advanced DSP (Digital Signal Processor) technology provides a wide array of studio quality effects. In addition to the Multi-Effects (EFX) section that features 40 different types of effects, the XP-30 also features an independent chorus unit and reverb unit (p. 61).

Extensive Tone Structure Range


Ten different Structures are available for combining basic sound elements for more flexible sound making. A ring modulator and booster enhance creating sounds (p. 70).

s Quick and Intuitive Operation


Enhanced Operational Ease
Dedicated buttons are provided for each function to simplify operation. The group of function buttons located below the display allow intuitive editing (p. 43).

An Array of Arpeggio and Cutting Options


With the [ARPEGGIO] on, you can create various arpeggios and simulate cutting techniques simply by pressing a chord. You can even specify the rhythmical feel you want (p. 56).

Featuring the Patch Search and Phrase Preview Functions that were Popular on the JV-2080
The Patch Search function (p. 32, 48) lets you rapidly find the patch you want simply by specifying a patch category. By pressing [PHRASE PREVIEW], you can then hear the selected patch play a phrase suitable for that type of patch. (Phrase Preview function, p. 33, 49)

General MIDI System Compatibility


The XP-30 provides a mode compatible with the General MIDI System, the standard format for desktop music (DTM) systems, and can play back commercially available General MIDI System compatible song data (p. 124).

General MIDI System


The General MIDI system is a set of recommendations which seeks to provide a way to go beyond the limitations of proprietary designs, and standardize the MIDI capabilities of sound generating devices. Sound generating devices and music files that meets the General MIDI standard bears the General MIDI logo ( ). Music files bearing the General MIDI logo can be played back using any General MIDI sound generating unit to produce essentially the same musical performance.

Use the Sound Palette Sliders to Make Quick Changes in the Sound
The four sliders in the PALETTE section let you make realtime changes in tone and volume while you play (p. 36, 50, 54).

s Computer Interface Connector


A special computer cable makes it easy for you to connect the XP-30 to your computer, so that you can enjoy ensemble playing (p. 134).

11

Front and Rear Panel

s Front Panel
A
Volume Slider
This slider adjusts the overall volume that is output from the rear panel OUTPUT jacks and PHONES jack. p. 26

[+OCT], [-OCT]
These buttons adjust the pitch of the keyboard in octave steps. p. 59 Pressing either of these buttons while holding down [TRANSPOSE] allows you to set the desired amount of transposition. p. 60

MODE Section

PALETTE Section

The buttons in this section select modes. The button indicator of the selected mode will light. p. 42

Use the four sliders to modify sounds in real time.

[PERFORM]/[GM]
Pressed to get into Performance mode. Hold down [SHIFT] while you press [PERFORM] to select GM mode. p. 51, 124

[FILTER/ENV]
Press this button ON when modifying filter and/or envelope settings in real time using the four sliders (CUTOFF/RESO./ ATTACK/DECAY). p. 36, 51, 54

[PATCH]/[PART]
Pressed to get into Patch mode. By holding down [PERFORM] and pressing [PATCH], you can modify the settings of the patch that is assigned to each part of the performance. p. 47, 54, 66

[LEVEL]
Press this button ON when adjusting volume balance in real time using the four sliders (1/2/3/4). p. 36, 51, 54

[SYSTEM]
This selects System mode. p. 108

[CONTROLLER]
Can be switched on when you wish to assign various parameters to the four sliders, and modify the sound as you play (C1/C2/C3/C4). p. 34

[RHYTHM]
This selects Rhythm Set mode. p. 55

[UTIL/CARD]
This selects Utility/Card mode. p. 115

KEY EFFECTS Section

The buttons in this section allow you to assign various functions to the keys of the XP-30s keyboard.

[EFFECTS ON/OFF]
This button turns the internal effects (Multi-Effects, Chorus, Reverb) on/off. p. 62

[PORTAMENTO]
Switches Portamento on/off. p. 35, 50

E
Display
Shows various information for the currently selected function or operation.

[SOLO]
Specifies playing a single note at a time. p. 35, 50

[TRANSPOSE]
Specifies transposing the keyboard in semitone steps. p. 60

[PHRASE PREVIEW]
Press this when you wish to use phrases to audition a patch. p. 33, 49

[ARPEGGIO]
Switches Arpeggiator on/off. p. 36, 56

12

Front and Rear Panel

[INC], [DEC]
Use these buttons to modify values. If you keep on holding down one button and pressing the other, the value change accelerates. If you press one of these buttons while holding down [SHIFT], the value will change in bigger increments. p. 45

], [ ], [

] (Cursor Buttons) ] (Page Buttons)

Move the cursor (underline) with these.

When the left edge of the display shows a or symbol, use these buttons to move to other parameter displays

[0][9] (Numeric Keys)


Use these to set a value. They can be used to enter numeric values as well as alphabetical characters. p. 45 When [CATEGORY] is on, this becomes the button for choosing a category group using the Patch Search function. p. 32, 48

[SHIFT] [EDIT]
Press this button when you wish to adjust various settings. Use the function buttons to select the display screen for the parameter you wish to modify. This is used in combination with other buttons. Some buttons on the front panel include grey-printed characters. They indicate the buttons function when [SHIFT] is held down.

[ENTER]/[DIGIT HOLD]
ENTER: Use this button to finalize a value or execute an operation. DIGIT HOLD: Press this button while holding down [SHIFT] to turn the Digit Hold function on/off. With the Digit Hold on, the 100s place and 10s place will be fixed and only the 1s place will change. This means that you can select Patches simply by pressing the numeric key for the 1s place, without having to press [ENTER]. The same applies when selecting Performances or Rhythm set. p. 48

Function Buttons
The function of these buttons will depend on the operational mode and the status of the [EDIT] indicator. p. 43

[18/916]
Use this button to select the group (18/916) of Parts to be selected by the function buttons. p. 43

[EXIT]/[PANIC]
EXIT: Press this button when you wish to return to the Play display of a mode, or to cancel an operation without executing. PANIC: If for some reason notes are stuck and continue sounding, hold down the SHIFT button and press this button to clear the stuck notes. p. 60

[CATEGORY]/[DEMO]
CATEGORY: Use the Patch Search function to select a patch. p. 32, 48 DEMO: To hear the demo playback, hold down [SHIFT] and press this button. p. 28

[UNDO/COMPARE]
The function of these buttons will depend on the operation being performed. UNDO: Press this button to restore a modified value to the original value. p. 63, 65, 66 COMPARE: When saving or copying Tone settings, press this to check the sound at the save destination, or at the copy source. p. 116, 118

WAVE EXPANSION Section

Here you can select sounds from a Wave Expansion. p. 31

[EXP A], [EXP B], [EXP C]


Select sounds from the internal Wave Expansion. EXP-A: Session EXP-B: Orchestral EXP-C: Techno Collection

[PALETTE EDIT]
Press this button when you wish to use the Palette display to modify Patch or Performance settings. p. 63, 65

[EXP D], [EXP E]


Select sounds from the Wave Expansion Board slots (EXP-D and E).

F
VALUE Dial
This dial is used to modify values. If you hold down [SHIFT] as you turn the VALUE dial, the value will change in greater increments. p. 45

H
Pitch Bend/Modulation Lever
This allows you to control pitch bend or apply vibrato. Depending on the settings, other specified parameters can also be controlled. p. 34, 75

13

Front and Rear Panel

s Rear Panel
Power Switch
Press to turn the power on/off. p. 26

CONTROL PEDAL Jack


You can connect optional expression pedals to these jacks. By assigning a desired function to a pedal, you can use it to select or modify sound or perform various other control. You can also connect optional pedal switches to sustain sound. p. 24, 110

AC Inlet
Connect the AC power cable (included) to this inlet. p. 24 * With units rated for 117V operation, the AC cable is already connected to the unit.
fig.0-02a

HOLD PEDAL Jack


An optional pedal switch can be connected to this jack for use as a hold pedal. p. 24, 110
fig.0-02e

MEMORY CARD Slot


An optional memory card (SmartMedia) can be inserted here. p. 115
fig.0-02b

OUTPUT Jacks (L (MONO), R)


These jacks output the audio signal to the connected mixer/ amplifier system in stereo. For mono output, use the L jack. p. 24

PHONES Jack
An optional set of headphones can be connected to this jack. p. 24

MIDI Connectors (IN, OUT, THRU)


These connectors can be connected to other MIDI devices to receive and transmit MIDI messages. p. 24, 119, 132
fig.0-02c

fig.0-02f

COMPUTER Switch
Set this switch depending on the type of computer connected to Computer connector, or the software you are using. Turn the power off before changing the setting of this switch. If you wish to use the MIDI connectors, set this switch to MIDI. p. 134

COMPUTER Connector
A special Computer cable (sold separately) can be connected here. The type of cable required will depend on your computer. When the Computer switch located at the left is set to MIDI, this connector cannot be used. p. 134
fig.0-02d

14

Quick Start

15

Quick Start

Getting Ready
Installing the Wave Expansion Board
Up to two Wave Expansion Boards (SR-JV80 series; sold separately) can be installed in EXP-D and E Slots in the XP-30. Wave Expansion Boards contain Wave data, as well as Patches and Rhythm Sets that use this Wave data, which can be called directly into the temporary area and played.
When playing a Patch or Rhythm Set that use the Wave data from a Wave Expansion Board, the appropriate Wave Expansion Board must be installed in the XP-30 for the sound to play correctly.

s Cautions When Installing an Wave Expansion Board


q To avoid the risk of damage to internal components that can be caused by static electricity, please carefully observe the following whenever you handle the board. Before you touch the board, always first grasp a metal object (such as a water pipe), so you are sure that any static electricity you might have been carrying has been discharged. When handling the board, grasp it only by its edges. Avoid touching any of the electronic components or connectors. Save the bag in which the board was originally shipped, and put the board back into it whenever you need to store or transport it. q Use a Philips screwdriver that is suitable for the size of the screw (a number 2 screwdriver). If an unsuitable screwdriver is used, the head of the screw may be stripped. q To remove a screw, rotate the screwdriver counter-clockwise. To tighten a screw, rotate loosen tighten the screwdriver clockwise. q When installing Wave Expansion Boards, remove only the specified screws. q Be careful that the screws you remove do not drop into the interior of the XP-30. q Do not leave the bottom cover in a detached state. Be sure to reattach it after the Wave Expansion Boards have been installed. q Do not touch any of the printed circuit pathways or connection terminals. q Be careful not to cut your hand on the edge of the installation bay. q Never use excessive force when installing a circuit board. If it doesnt fit properly on the first attempt, remove the board and try again. q When circuit board installation is complete, double-check your work. To install an optional Wave Expansion Board (SR-JV80 series; sold separately), the units bottom cover must be removed. There are two slots (EXP-D and E) into which a board can be installed. Slots EXP-D and E correspond to the group (XP-D and E) you need to select in order to use a Wave, Patch or Rhythm Set from the Wave Expansion Board.

16

Getting Ready

Before installing the Wave Expansion Board, turn off the power of the XP-30 and all connected devices, and disconnect all cables from the XP-30. Turn the XP-30 on its back, and remove only the screws shown in the following diagram.
Screws to be removed

2
fig.Q-02a.e

If the same type of Wave Expansion Board is installed in the EXP-D slot and the EXP-E slot, it will only be possible to select data from the Wave Expansion Board that was installed in the EXP-D slot. Also, the XP-30 already contains the data of the following three Wave Expansion Boards, so if one of these Wave Expansion Boards is installed, only the internal data (XP-AC) can be selected. SR-JV80-09 Session (XP-A) SR-JV80-02 Orchestral (XP-B) SR-JV80-11 Techno Collection (XP-C)

Inside, there are two connectors and six board holders. Insert the connectors of the Wave Expansion Board into the internal connectors, and simultaneously insert the board holders into the holes of the Wave Expansion Board.
Wave Expansion Board

fig.Q-02b.e

Board holder Connector

EXP E EXP D

17

Quick Start

Getting Ready

4
fig.Q-02c.e

Use the Installation Tool supplied with the Wave Expansion Board to turn the holders in the LOCK direction, so the board will be fastened in place.
LOCK

Installation tool

Use the screws that you removed in step 2 to fasten the cover back in place.
This completes installation of the Wave Expansion Board.

6 7 8
fig.Q-03

Connect the cables that you disconnected earlier. Turn on the power, as described in Turning On the Power (p. 26). Press [PATCH] to access the PATCH PLAY display.

18

Getting Ready

Press [EXP D] or [EXP E], and verify that you can select patches from Wave Expansion Boards D or E. [EXP D] or [EXP E] indicator will light, and the following display will appear.

fig.Q-04

The example here depicts what you would see if the SR-JV80-13 Vocal Collection Wave Expansion Board were installed in the EXP-D slot.

If you cant choose any Wave Expansion Board patches, its possible that the installed Wave Expansion Board is not being recognized correctly. Turn off the power as described in Turning Off the Power (p. 26), and re-install the Wave Expansion Board correctly.

19

Quick Start

Getting Ready

Installation de la carte dextension Wave


(French language for Canadian Safety Standard)
Vous pouvez installer jusqu 2 cartes dextension Wave (en option dans la srie SR-JV80) dans les crneaux EXP-D et E du XP-30. Les cartes dextension Wave contiennent des donnes Wave, aussi bien que des morceaux musicaux et des ensembles rythmiques utilisant ces donnes, auxquelles on peut directement accder dans la zone temporaire et les faire jouer.

s Precautions lors de linstallation de la carte dextension Wave


q Pour viter tout dommage des composants internes pouvant provenir de llectricit statique, veuillez suivre les conseils suivants quand vous installez la carte. Avant de toucher la carte, saisissez toujours un objet mtallique (tuyau deau ou autre) pour tre sr que llectricit statique se dcharge. Quand vous saisissez la carte, prenez-la par les bords. Evitez de toucher les composants lectroniques ou les connecteurs. Conservez le sac dans lequel la carte tait emballe et remettez la carte dedans pour lexpdier ou lentreposer. q Utiliser un tournevis cruciforme correspondant la taille de la vis (un tournevis numro 2). En cas dutilisation dun tournevis inappropri, la tte de la vis pourrait tre endommage. q Pour enlever les vis, tourner le tournevis dans le sens contraire des aiguilles dune desserrer resserrer montre. Pour resserrer, tourner dans le sens des aiguilles dune montre. q Lors de linsertion de la carte dextension Wave, enlevez seulement les vis indiques dans les instructions. q Veillez ne pas laisser tomber de vis dans le chssis du XP-30. q Ne pas laisser le panneau de protection avant dtach. Sassurer de lavoir rattacher aprs avoir install le disque dur. q Ne touchez aucun des circuits imprims ni les bornes de connexion. q Veillez ne pas vous couper les doitgs sur le bord de louverture dinstallation. q Ne jamais forcer quand vous installez une carte de circuits. Si la carte ne rentre pas correctement, ressortez-la et ressayez. q Quand la carte est installe, vrifiez si linstallation est correcte. Pour installer une carte dextension Wave optionnelle (srie SR-JV80), le panneau du bas de lappareil doit tre enlev. Vous trouverez 2 crneaux (EXP-D et E) dans lesquels vous pourrez installer une carte. Les crneaux EXP-D et E correspondent au groupe (XP-D et E) que vous devez slectionner pour pouvoir utiliser une donne Wave, un morceau musical ou un ensemble rythmique de la carte dextension.

Quand vous faites jouer un morceau ou un ensemble rythmique qui utilise des donnes Wave de la carte dextension, une carte dextension approprie doit tre installe dans le XP-30 afin que le son sorte correctement.

20

Getting Ready

1 2
fig.Q-02a.f

teindre le XP-30 et tous les appareils qui y sont relis et dbrancher tous les cbles du XP-30. Retournez le XP-30 et enlevez seulement les vis indiques sur la figure.
Vis enlever

Si la mme sorte de carte dextension Wave est installe dans les crneaux EXP-D et EXP-E, il ne sera possible de slectionner que les donnes de la carte dextension Wave installe dans le crneau EXP-D. De plus, le XP-30 contient dj les donnes des 3 cartes dextension Wave suivantes si bien que si une de ces 3 cartes est installe, seules les donnes internes (XP-AC) pourront tre slectionnes. SR-JV80-09 Session (XP-A) SR-JV80-02 Orchestral (XP-B) SR-JV80-11 Techno Collection (XP-C)

lintrieur, il y a 2 connecteurs et 6 supports carte. Insrer les connecteurs de la carte dextension Wave dans les connecteurs internes tout en insrant simultanment les supports carte dans les trous de celle-ci.
Carte d'extension Wave

fig.Q-02b.f

Support carte Connecteur

EXP E EXP D

21

Quick Start

Getting Ready

4
fig.Q-02c.f

Pour tourner les supports en position LOCK (verrouill), utilisez loutil dinstallation de la carte dextension fournie cet effet. De cette faon, la carte sera bien fixe sa place.
LOCK

Outil d'installation

Reposez le couvercle en remettant les vis enleves (comme spcifi) ltape 2.


Linstallation de la carte dextension Wave est termine.

6 7 8
fig.Q-03

Rabranchez les cbles. Mettez le XP-30 sous tension en procdant comme indiqu dans Turning On the Power (p. 26). Appuyer sur [PATCH] pour accder la page PATCH PLAY.

22

Getting Ready

Appuyer sur [EXP D] ou [EXP E] et vrifier si vous pouvez slectionner les morceaux musicaux des cartes dextension Wave D ou E. Lindicateur [EXP D] ou [EXP E] sallumera et laffichage suivant apparatra.

fig.Q-04

Ceci est un exemple daffichage lorsque la carte dextension Wave SR-JV8013 Vocal Collection est installe dans le crneau EXP-D.

Si vous ne pouvez choisir aucun des morceaux musicaux de la carte dextension Wave, il est possible que la carte installe ne soit pas reconnue correctement. teignez lappareil comme indiqu dans Turning Off the Power (p. 26) et rinstaller la carte correctement.

23

Quick Start

Getting Ready

Making Connections
The XP-30 does not contain an amp or speakers. In order to hear sound, you will need to connect it to a keyboard amp, audio system, or headphones. Refer to the following diagram and connect the XP-30 to the external equipment you are using.
fig.Q-05.e

to Power outlet

External MIDI device

Roland

Stereo headphones Pedal switch

Expression pedal (EV-5) or pedal switch

Stereo set, etc.

Speaker with built-in amp, keyboard amp, etc.

Before you make connections, make sure that power is turned off for all devices.

To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections.

24

Getting Ready

Connect supplied AC power cable to the XP-30, and plug the other end into an AC power outlet.

On 117V models the AC cable is permanently attached to the unit.

Connect audio cables and MIDI cables as shown in the diagram. If you are using headphones, plug them into the PHONES jack. Connect pedal switches or expression pedals as necessary.

In order to take full advantage of the XP-30s performance, we recommend using a stereo amp/speaker system, If you are using a mono system, make you connections to the OUTPUT jack L (MONO).

CONTROL PEDAL jack can also accommodate pedal switches.

Use only the specified expression pedal (EV-5; sold separately). By connecting any other expression pedals, you risk causing malfunction and/ or damage to the unit.

For information on making the connection with the computer, take a look at

Connecting to Your Computer (p. 134).

25

Quick Start

Getting Ready

Turning On the Power

Before you turn the power on, check to make sure that:
All external devices are correctly connected to the XP-30. The volume controls of the XP-30 and the amp/mixer system are turned down all the way.

2
fig.Q-06

Turn on the power switch located on the rear panel of the XP30.

Once the connections have been completed (p. 24), turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices.

3 4
fig.Q-07

Turn the power on of your amp or audio system. Play the XP-30 and gradually raise the volume controls of the XP-30, your amp or mixer to an appropriate volume level.

This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally.

Be careful not to raise the VOLUME slider of the XP30 too much. Excessive volume may damage your amp/speaker system or could cause hearing

s Turning Off the Power

Before you turn power off, check to make sure that:


The volume controls of the XP-30 and the amp/mixer system are turned down all the way. Important data has been saved to a memory card (p. 122).

2 3
26

Turn off your amp/mixer system. Turn off the XP-30 power.

Getting Ready

Before using XP-30 for the first time, reset it to its default factory settings using Factory Reset. Different settings may result in unexpected effects.
fig.Q-08

3 4

1
fig.Q-09

Press [UTIL/CARD] to make the indicator blink.


The UTIL 1 display will appear.
Factory Reset operation resets all data in the internal memory and user memory to factory presets. Save any important data to a memory card before executing this operation (p. 122).

2
fig.Q-09a

Press [ ].
The UTIL 2 display will appear.

3
fig.Q-10

Press the numeric key [4].


The FACTORY RESET display will appear.

Press [ENTER].
If Internal Write Protect= ON message is displayed, press [DEC] to turn the setting OFF. After pressing [ENTER] to clear the message, press [ENTER] again to reset to the factory preset settings.

For more information about the Internal Write Protect, please refer to

Preventing User Memory Writing Operation (PROTECT)


(p. 121).

27

Quick Start

Reset to Default Factory Settings (Factory Reset)

Listening to the Demo Song


The XP-30 contains 9 demo songs and you use Demo Play to play it. Its the easiest introduction to the XP-30s exceptional sounds and effects. Demo Song TRANSFERENCE CHANTERELLE VECTORIAL All In Good Time TEKKNO MILLENNIUM A Shadows March Guitars Forever Rude99 Overtime Composer/Copyright Scott Tibbs 1999 Roland Corporation Scott Tibbs 1999 Roland Corporation Scott Tibbs 1999 Roland Corporation Scott Wilkie 1999 Scott Wilkie Media (ASCAP) MASA 1999 COPYRIGHT CONTROL Steve Lu 1999 Stephen Lu Gundy Keller 1999 Gundy Keller / A-TOWN recordings Hans-Joerg Scheffler 1999 Hans Scheffler Hans-Joerg Scheffler 1999 Hans Scheffler

All rights reserved. Unauthorized use of this material for purposes other than private, personal enjoyment is a violation of applicable laws.

fig.Q-11

1
fig.Q-12

Hold down [SHIFT] and press [CATEGORY].


The DEMO PLAY display will appear.

Turn the VALUE dial or press [INC]/[DEC] to select the song that you wish to hear.
If you select CHAIN-PLAY, the songs will playback successively, beginning from the first.

Press [ENTER] to start demo song playback.


When a demo song plays all the way to the end, it automatically returns to the start of the song, and playback is repeated. To interrupt playback, press [EXIT].

fig.Q-13

No data for the music that is played will be output from MIDI OUT.

4
28

To return to the previous display, press [EXIT].

Listening to the Demo Song

s Profile of the Composer


Scott Tibbs
Scott Tibbs has performed and conducted for several orchestral groups, including the Atlanta Symphony Orchestra, throughout the United States, Canada, Latin America, and Japan. His diverse compositional output ranges from numerous film, theater and television projects to the symphonic concert stage. For the past four years, he has been teaching music composition and theory at UCLA where he has received a Ph.D. degree in composition. He has performed with well-known artists Dizzy Gillespie, Bill Cosby, Jerry Sienfeld, and Bobby Shew, amongst numerous others.

Gundy Keller
Gundy Keller, a Germany-based guitarist, songwriter and producer, has been an international demonstrator for Roland since 1986. Gundy focuses mainly on the GR synthesizers and the V-Guitar, for international music conventions as well as recording sessions requesting completely unusual guitar sounds. Besides creating his own production company, hes the founder and director of Rocksound Music School, a private institute for music instruction. Check out some of his other work on the Roland VG-8 Demo CD, or the Roland GR-30 Video.

Steve Lu
Steve Lu is a recent graduate of Berklee College of Music, majoring in Music Production & Engineering. His recent musical efforts include a soundtrack album, featuring synthesized re-creations of movie themes such as Titanic and The Rock, as well as production and arrangements for saxophonist Jimmy Reids self-titled album. He is currently working with artists Brandy and Ray-J on future projects.

Scott Wilkie
Scott Wilkie is a contemporary jazz recording artist, based in southern California. He tours frequently with his own band, and also appears as an artist for Roland in the U.S., Japan, Europe and South America. His debut solo album, Boundless, was released worldwide in 1999 on Narada/Virgin Records. You can find him on-line at www.scottwilkie.com.

Hans-Joerg Scheffler
Born and raised in the Ruhr valley, the biggest industrial area in Germany, Hanss attraction to noise and rhythm came naturally. Today he runs his own company, DIGITAL AUDIO DESIGN, which produces sampling CDs and CD ROMs. He works for Roland as a pro audio product specialist, as a sound designer for expansion boards, and as a composer of demo songs. He has released several CDs that use the Roland RSS system. Soundclips of his work can be downloaded at: http://www.united-sound.com/usmaster/cell2downde.htm

MASA
Masa has performed live, mainly at psychedelic-trance parties since the early 90s. In the spring of 1996, he released the album Just Inside from East-West. Interest in his work is increasing, and new releases are appearing under a variety of labels, including Tokyo Tekno Tribe Records and Psy-Harmonics. Web site: www.ifnet.or.jp/~masa-k/

29

Quick Start

Playing the Sounds


Selecting Patches and Playing the Sounds
The XP-30 contains a large number of sounds ready for you to play. The sounds that you select and play on the XP-30 are generally called Patches. Heres how to select and play Patches.
fig.Q-14

1
fig.Q-15

Press [PATCH] to make the indicator light.


The PATCH PLAY display will appear.

2 3 4

Play the keyboard and listen to the sound. To select a different Patch, turn the VALUE dial or press [INC]/[DEC].

To change the Patch Group, hold down [SHIFT] and press any key from [1] through [6] on the numeric keypad.
[SHIFT] + [1]: PR-A (Preset A) [SHIFT] + [2]: PR-B (Preset B) [SHIFT] + [3]: PR-C (Preset C) [SHIFT] + [4]: PR-D (GM (General MIDI)) [SHIFT] + [5]: PR-E (Preset E) [SHIFT] + [6]: USER (User)

By using the Phrase Preview function, you can audition patches by listening to a preset phrase suitable for the selected type of patch (p. 33).

30

Playing the Sounds

The XP-30 contains the patches of the following popular Wave Expansion Boards: SR-JV80-09 Session SR-JV80-02 Orchestral SR-JV80-11 Techno Collection Heres how to select and play these patches.
fig.Q-16

1
fig.Q-15

Press [PATCH] to make the indicator light.


The PATCH PLAY display will appear.

Press [EXP A][EXP C] to select the Wave Expansion Patch that you wish to hear.
[EXP A]: Session [EXP B]: Orchestral [EXP C]: Techno Collection

fig.Q-17

When a Wave Expansion Board of the SR-JV80 series (sold separately) is installed in the EXP-D or EXP-E Wave Expansion Board slot, you can press [EXP D] or [EXP E] to choose the corresponding patches.

3 4

Play the keyboard and listen to the sound. To select a different Patch, turn the VALUE dial or press [INC]/[DEC].

By using the Phrase Preview function, you can audition patches by listening to a preset phrase suitable for the selected type of patch (p. 33).

31

Quick Start

Selecting Wave Expansion Patches

Playing the Sounds

Selecting Patches by Category (Patch Search Function)


The JV-2080 provides a Patch Search Function that allows you to quickly find Patches of the specified type (Category). The 38 categories are organized into 10 groups. Heres an example of how to find organ-type Patches.
fig.Q-18

2,6 3 4

1
fig.Q-15

Press [PATCH] to make the indicator light.


The PATCH PLAY display will appear.

2
fig.Q-19

Press [CATEGORY] to make the indicator light.


The Patch Search function will be turned on, and the patch number display will change to the category display.
Now you can select patches within the specified category, either by rotating the VALUE dial, or by using [INC] or [DEC]. To change the category group, use the numeric keys.

3
fig.Q-20

Select the category. Hold down [CATEGORY] and press [2 (KEY&ORG)].

For this example, select the Organ category (ORG) by pressing numeric key [4].
Organ-type patches can now be selected.

For details on the categories you can select, refer to page 49.

32

Playing the Sounds

Turn the VALUE dial or press [INC]/[DEC] to select a patch.

Press [CATEGORY] to make the indicator go dark.


The Patch Search function will be turned off, and the normal PATCH PLAY display will reappear.

By using the Phrase Preview function, you can audition patches by listening to a preset phrase suitable for the selected type of patch (p. 33).

Auditioning the Patches (Phrase Preview)


The XP-30 allows you to preview Patches by hearing a phrase appropriate for each type of Patch.
fig.Q-21

1 2,3

1
fig.Q-15

Press [PATCH] to make the indicator light.


The PATCH PLAY display will appear.

Press and hold [PHRASE PREVIEW].


If the factory settings have just been restored, the USER: 001 Temple of XP Patch will sound.

Release your finger from [PHRASE PREVIEW], and the phrase will stop playing.

You can change the phrase that is played by the Phrase Preview, and modify the way in which the phrase is played. For details, refer to

Using Phrase Preview to Play Patches (p. 49), and Phrase Preview Settings (PREVIEW)
(p. 113).

33

Quick Start

Playing the Sounds

Try Out Performance Functions


The XP-30 provides various controllers that can modify the sound. While playing patches, try out these controllers and listen to effects they can produce.
The effect that the controllers have will depend on the settings of the selected Patch. If the effects of the controllers are difficult to detect, select another Patch.

s Velocity/Aftertouch
The force with which you play the keyboard (velocity) can affect the volume or timbre of the sound. Aftertouch (pressure you apply to a key after playing a note) can also affect the sound.

s Pitch Bend/Modulation Lever


While playing the keyboard, move the lever to the left to lower the pitch, or to the right to raise the pitch. This is known as Pitch Bend. You can also apply vibrato by manipulating the lever away from you. This is known as Modulation. If you move the lever away from you and at the same time move it to the right or left, you can apply both effects simultaneously.
fig.Q-22.e

Modulation

Pitch Bend

s C1C4 Slider
By moving the sliders up and down while fingering the keyboard, you can control the various functions assigned to the sliders. To control them, press [CONTROLLER] to make the indicators light up, then move the sliders. Additionally, if you hold down [CONTROLLER] while moving one of the C1C4 sliders, you can go to the ASSIGN display for that slider. There you can check and make settings for the function that is to be controlled with the slider. Make changes in the settings while holding down [CONTROLLER].
fig.Q-23

At the factory default settings, you can use the C1 through C4 sliders to control the functions described below.

C1: AFTERTAUCH C2: BREATH C3: PORTA-TIME


(Portamento time) C4: MODULATION

How sound varies depends on the current setting. For details, refer to C1/C2/

C3/C4 ASSIGN (C1/C2/ C3/C4 Slider Assign)


(p. 111).

34

Playing the Sounds

If an optional pedal switch is connected to the rear panel HOLD PEDAL jack, pressing the pedal switch will sustain (hold) the sound even if the keys are released.

s Expression Pedal
If an optional expression pedal is connected to any of the rear panel CONTROL PEDAL jack, you can use the pedal to control the volume or timbre of sound.
How sound varies depends on the current setting. For details, refer to CONTROL PEDAL (p. 110).

s Solo
You can play using single notes, by pressing [SOLO] (indicator lights). This function is especially effective when playing a sax, flute or other monophonic instrument. Using [PORTAMENTO] with [SOLO] ON allows you to simulate performance techniques like violin glissandos.
fig.Q-24

For details, refer to

Playing Single Notes (Solo) (p. 50).

s Portamento
As you play the keyboard, you can make pitch slide smoothly from one key to another, by pressing [PORTAMENTO] (indicator lights).
fig.Q-25

For details, refer to

Creating Smooth Pitch Changes (Portamento) (p. 50).

35

Quick Start

s Hold Pedal

Playing the Sounds

s Sound Palette
While playing the keyboard, you can move the sliders up or down to modify volume level or sound character. To change sound character, press [FILTER/ENV] to light the indicator and move the sliders. To change the volume level, press [LEVEL] to light the indicator and move the sliders.
fig.Q-26

For details, refer to Using

the Sliders to Modify the Sound in Realtime (Sound Palette Function) (p. 50, 54).

Play Arpeggios (Arpeggiator)


You can play a broken chord (arpeggio) automatically, by simply pressing a chord. For example, if you press a C major chord, the XP-30 plays an arpeggio such as C E G C E G...
fig.Q-27

2,4,5,7

1
fig.Q-15

Press [PATCH] to make the indicator light.


The PATCH PLAY display will appear.

Press [ARPEGGIO] to make the indicator light.

36

Playing the Sounds

Play a chord.
XP-30 will play an arpeggio, according to the notes forming the chord you have just voiced.

4
fig.Q-28

Continue holding down [ARPEGGIO], and the ARP SELECT display will appear.

In this page you can change the Style, Accent Rate, Octave Range and Tempo of the arpeggio. Heres how to change the Style.

Hold down [ARPEGGIO], and press [ ] or [ ] to move the cursor (underline) to the Style parameter. Then rotate the VALUE dial to select various settings.
Depending on the value you enter, the way arpeggios play will vary.

For details regarding playing arpeggios, refer to

Playing an Arpeggio
(p. 56) and Arpeggio

Settings (ARPEGGIO)
(p. 108).

Hold down [ARPEGGIO] and press [TRANSPOSE]. The [ARPEGGIO] indicator will begin blinking, and the arpeggio will continue sounding even after you take your hand off the keyboard (Hold).
To stop the arpeggio from being sounded by the Hold function, hold down [ARPEGGIO] again and press [TRANSPOSE]. The indicator changes from blinking to lit.

To finish playing arpeggios, press [ARPEGGIO] again so the indicator turns off.

37

Quick Start

Playing the Sounds

Play Percussion Sounds from the Keyboard


The XP-30s Rhythm Sets contain a wide variety of percussion sounds and special effects. Heres how to select a Rhythm Set and play percussion sounds.
fig.Q-29

1
fig.Q-30

Press [RHYTHM] to make the indicator light.


The RHYTHM PLAY display will appear.

Press different keys to play different percussion instruments.


The display will indicate the last-pressed key (Note name) and the percussion instrument name (Rhythm Tone name) assigned to that key.

To select another Rhythm Set, turn the VALUE dial or press [INC]/[DEC].

The percussion instrument played by each key will depend on the selected Rhythm Set. For details, refer to Rhythm Set List (p. 177).

38

Advanced Use

39

Chapter 6 Chapter 5 Chapter 4 Chapter 3 Chapter 2 Chapter 1

Chapter 1. Overview of the XP-30


XP-30 Configuration
s Basic Configuration
The XP-30 consists of a sound source and controllers.
fig.1-01.e

s Classification of XP-30 Sound Types


XP-30 sounds are made up of the following types:

Tones
In the XP-30, the Tone is the smallest class of sound. Each Tone consists of one sound. But when you play the XP-30 you will mostly play a Patch, which is made up of several Tones. Tones therefore are the elements which collectively form a Patch. Tone configuration:
fig.1-02.e

Sound source section

Play

Tone
Controller section (controllers such as keyboard, pitch bend lever, etc.)

LFO 1

LFO 2

Sound Source
The XP-30 sound source produces sound by responding to commands in the form of MIDI messages received from its controllers. It will also produce sound by responding to commands received from various external devices it can be connected to.

WG

TVF

TVA

Pitch Envelope

TVF Envelope

TVA Envelope

Controllers
Controllers include the keyboard, front panel sliders and pedals which are connected to their respective rear panel jacks. Adjusting these controllers enable you to produce or modify sound.

audio signal

control signal

WG (Wave Generator)
Using the Wave Generator, you select a waveform and set its pitch.

TVF (Time Variant Filter)


With the Time Variant Filter, you modify the waveforms frequency characteristics.

TVA (Time Variant Amplifier)


With the Time Variant Amplifier, you set volume level and set the sounds position in a stereo soundfield.

Envelope
You use Envelope to initiate changes to occur to a sound over time. There are separate Envelopes for the WG (pitch), TVF (filter) and TVA (volume). For example, to modify a sounds attack and decay time, you would use TVA Envelope to adjust volume changes to the sound over time.

LFO (Low Frequency Oscillator)


Use the LFO to create cyclic changes (modulation) in a sound. The XP-30 has two LFOs. Either one or both can be applied to effect the WG (pitch), TVF (filter) and/or TVA (volume). To illustrate this controls action, you can apply an LFO to modify the WG (pitch) to create vibrato. If the LFO is used to modify the TVA (volume), youll get tremolo.

40

Chapter 1. Overview of the XP-30

Patches
Patches are the basic sound configurations that you play during a performance. Each Patch can be configured by combining up to four Tones. How the four Tones are combined is determined on the STRUCT display (PATCH/ COMMON).
fig.1-03.e

Rhythm Sets
A Rhythm Set is a grouping of percussion instruments (Rhythm Tones). Since percussion instruments generally do not play melodies, there is no need for a percussion instrument sound to be able to play a scale on the keyboard. It is however, more important that as many as possible percussion instruments be available to you at the same time. Therefore, each key (Note number) of a Rhythm Set will produce a different percussion instrument.
fig.1-05.e

Patch

Tone 4 Tone 3 Tone 2 Tone 1

Rhythm Set

Note Number 98 (D7) Note Number 97 (C#7)

LFO 1

LFO 2
Note Number 36 (C2) Note Number 35 (B1)
Rhythm Tone (Percussion instrument sound)
WG TVF TVA

WG

TVF

TVA
Pitch Envelope TVF Envelope TVA Envelope

Pitch Envelope

TVF Envelope

TVA Envelope

Parts Performances
The next level in sound configuration. A single Performance groups 15 Patches and one Rhythm Set so that they can be combined to play ensembles or produce fabulously rich, thick sounds. One Performance allows a single XP-30 to control up to 16 instrument sounds. Because the XP-30 sound source can control multiple sounds (instruments) it is called a multitimbral sound source.
fig.1-04.e

When the XP-30 is used as a multitimbral sound source, another sound configuration called a Part comes into play. A Part contains a Patch or Rhythm Set. For multitimbral applications, the Performance consists of 16 Parts. A specific Patch can be assigned to each Part except Part 10 because Part 10 is universally set as the Drum Part to which a Rhythm Set (discussed above) is assigned. In a multitimbral context, it helps to think of a Performance as an orchestra, each Part in it being a musician, and the Patch or Rhythm Set that musicians instrument. For details regarding following items, please refer to each corresponding page. About the Memory (p. 67) About the Effects (p. 61)

Performance
Part 16 (MIDI receive ch.) Part 11 (MIDI receive ch.)

Patch
Keyboard, MIDI Part 10 (MIDI receive ch.)

Rhythm Set
Part 9 (MIDI receive ch.)

Sound

Part 1 (MIDI receive ch.)

Patch

41

Chapter 1

Chapter 1. Overview of the XP-30

s Number of Simultaneous Voices


The XP-30 is able to produce up to 64 voices simultaneously. The following paragraphs discuss what this means, and what will happen when more than 64 simultaneous voices are requested from the XP-30.

Basic Operation
s Switching Modes
The XP-30 contains a large number of functions. In order to organize these functions for easy access, they are grouped into the following modes. The mode that is selected will affect the way in which the sound source operates, how data is shown in the display, and how the function buttons work. Use the Mode buttons to select the mode. The indicator of the selected button will light/blink, and the display will change according to the selected mode.
fig.1-06

Calculating the Number of Voices Being Used


The XP-30 is able to produce up to 64 simultaneous voices. However this number is not simply the number of notes being played, but depends on the number of Tones used in each Patch. If you are playing one Patch which uses 4 Tones, you will be able to play 16 simultaneous notes. If you are using the XP-30 in Performance mode to play an ensemble, count the total number of Tones used by all the Parts using the following formula. (currently sounding notes) x (number of Tones used in the Patch being played)

How a Patch Uses Notes


When the XP-30 is requested to play more than 64 voices simultaneously, a currently-sounding note will be turned off to make room for the newly requested note. The note with the lowest priority will be turned off first. The order of priority is determined by the Voice Priority setting. Voice Priority can be set either to Last or Loudest. When Last is selected, a newly requested note that exceeds the 64 voice limit will cause the first-played of the currently sounding notes to be turned off. When Loudest is selected, the quietest of the currently sounding notes will be turned off. Normally you will set Voice Priority to Last.

Sound Source
Selecting Patch mode, Performance mode, Rhythm Set mode, and GM mode will determine sound source operation. One mode always has to be selected.

Patch Mode
In this mode, you can play an individual Patch from the keyboard or modify Patch settings. If youre using an external MIDI device to control the XP-30 in this mode, it will function as a single-patch sound source.

Performance Mode
This mode makes the XP-30 function as a multitimbral sound source, and Performance settings can be modified. If youre using an external MIDI device to control the XP-30 in this mode, it will function as a multitimbral sound source. To modify the settings of a Patch thats assigned to a Part, hold down [PERFORM] and press [PATCH]. Both button indicators will light.

Note Priority in Performance Mode


Since Performance mode is usually used to play an ensemble consisting of several Patches, it is important to decide which Parts take priority. Priority is specified by the Voice Reserve settings. When a note within a Patch needs to be turned off to make room for a new note, the Voice Priority setting of the Patch will apply.

Voice Reserve
The XP-30 has a Voice Reserve function that lets you reserve a minimum number of notes that will always be available for each Part. For example if Voice Reserve is set to 10 for Part 16, Part 16 will always have 10 notes of sound-producing capacity available to it even if a total of more than 64 notes (total for all Parts) are being requested. When you make Voice Reserve settings, you need to take into account the number of notes you want to play on each Part as well as the number of Tones used by the selected Patch. * It is not possible to make Voice Reserve settings that would cause the total of all Parts to be greater than 64 voices.

Rhythm Set Mode


This is how you can play a Rhythm Set from the keyboard and modify the Rhythm Set settings. In this mode, the keyboard will play the Rhythm Set, but the XP-30 continues to function as a multitimbral sound source. So your effects settings of the currently selected Performance will be heard as you play the Rhythm Set. Rhythm Sets are assigned to Part 10 of the Performance. If youre using an external MIDI device to control the XP-30 in this mode, it will still function as a multitimbral sound source.

42

Chapter 1. Overview of the XP-30

GM Mode
This special mode makes the XP-30 function as a GM compatible sound source. You should select this mode when you want to play back a GM score (music files created for GM sound source). To set GM mode, hold down [SHIFT] and press [PERFORM]. [PERFORM], [PATCH] and [RHYTHM] indicators will not light.

s About the Function Buttons


Function buttons are buttons that perform a variety of functions. The function they perform will depend on the current mode, and on whether [EDIT] is on (lit) or off (dark). [EDIT] will turn on or off each time you press it.
fig.1-07

System Mode
This mode is for determining global XP-30 settings such as tuning, display contrast and how MIDI messages are received. * Some System mode parameters relate to an entire Patch or an entire Performance. To set these parameters, press [SYSTEM] in the selected mode (Patch or Performance).

* [EDIT] switches the function of the function buttons, but pressing [EDIT] will not make the display change. If you wish to modify a setting, press the [EDIT] to make the indicator light, and then press a function button to select the display group and switch the display. When you finish making settings, press [EXIT] or a mode button to switch the display.

Utility/Card Mode
Here you can save and transmit settings for the sound generator, and make settings related to memory cards. * Some Utility/Card mode parameters relate to an entire Patch, Performance or Rhythm Set. To set these parameters, press [UTIL/CARD] in the selected mode (Patch, Performance or Rhythm Set).

In Performance Mode ([EDIT] Indicator is Dark)


fig.1-08

The function buttons will act as Part buttons ([PART]) that switch Parts on (lit) or off (dark). Since 16 Parts are being controlled using only 8 buttons, use [1-8/9-16] to select which set of Parts you are controlling. When [1-8/9-16] indicator is dark, you can switch Parts 18 on/off. When it is lit, you can switch Parts 916 on/off. If the [EDIT] indicator is turned off in the Part setting display, the function buttons will act as PART buttons that select the Part to be edited. * The function of the Part on/off setting will depend on the setting of the Key Mode parameter (PERFORM/COMMON/ PERFORM COMMON) (p. 83).

43

Chapter 1

Chapter 1. Overview of the XP-30

In Patch Mode ([EDIT] Indicator is Dark)


fig.1-09

s About the Cursor Buttons


The cursor buttons are used to move between display pages or to move the cursor.
fig.1-12

The function buttons will act as Tone Switch buttons ([TONE SWITCH]) and Tone Select buttons ([TONE SELECT]). [TONE SWITCH] allow you to turn each Tone in the Patch on (lit) or off (dark). When a Tone is turned on, it can be heard. Use [TONE SELECT] to select the Tone you wish to modify. To select a Tone to modify, turn off [EDIT] indicator in the Tone setting display. To select two or more Tones simultaneously, hold down one of [TONE SELECT] and press the other [TONE SELECT]. In this case, the numbers of Tones other than the first-selected Tone will be displayed as * symbols.

Moving Between Display Pages


The various displays are grouped by function button, and each group contains several display pages. Use the cursor buttons to move between these display pages and groups.

In Rhythm Set Mode ([EDIT] Indicator is Dark)


fig.1-10

Moving Between Pages


An upward-pointing arrow ( ) shown in the display indicates that one or more pages exist before this page. A downward-pointing arrow ( ) shown in the display indicates that one or more pages exist after this page. Press [ ] to move to the previous page, or [ ] to move to the next page. Pressing [ ] while holding [SHIFT] will jump to the first page. Pressing [ ] while holding [SHIFT] will jump to the last page.
fig.1-13

The function buttons (TONE SELECT section) will select the key shown in the display. If the [EDIT] indicator is turned off in the Rhythm Set setting display (the setting display for individual keys), the function buttons will select the key to be edited. [TONE SELECT 1]: move to an octave lower key [TONE SELECT 2]: move to the semitone below [TONE SELECT 3]: move to the semitone above [TONE SELECT 4]: move to an octave higher key

Moving Between Groups


From one of the Play displays, hold down [SHIFT] and press [ ] to access the left-most function button group display. In group displays that you select using the function buttons, you can hold down [SHIFT] and press [ ] to move to the group of the function button to the left, or hold down [SHIFT] and press [ ] to move to the group of the function button to the right. Whenever you are in any group display, you can move to another group even if [EDIT] indicator is dark. In other words, this procedure allows you to move to a different group without having to turn on [EDIT] indicator, and is a faster and more efficient way to get around.

When [EDIT] Indicator is Lit


Each mode contains a large number of settable items, and these items are organized into groups. When [EDIT] indicator is lit, the function buttons are used to select display groups. The displays that appear will depend on the current mode. The groups that can be selected in each mode are printed on the front panel above the buttons.
fig.1-11

* For information on what the function buttons do in GM mode, please see Chapter 5. Using the XP-30 as the GM Sound Module (p. 124).

44

Chapter 1. Overview of the XP-30

Moving the Cursor (underline)


When two or more items are shown in a single display page, move the cursor (underline) to the item whose value you wish to set. Press [ ] to move the cursor to the left, or [ ] to move it to the right.
fig.1-14

[0][9] (Numeric Keys)


[0][9] (Numeric Keys) lets you directly specify a numerical value. When you enter the number, the value will blink. This indicates that the value has not yet been finalized. To finalize the value press the ENTER button. To reverse the sign of the number (+/-), hold down [SHIFT] and press [0]. * Some parameters do not require you to press [ENTER] to finalize the value. < Example 1: To enter a value of 38 > Press [3] press [8] press [ENTER] < Example 2: To enter a value of -60 > While holding down [SHIFT] press [0] press [6] press [0] press [ENTER] * You can switch from a positive to negative numerical value anytime before you press [ENTER].

fig.1-15

Special Functions of the Numeric Keys

s Modifying a Value
To modify a value, use the VALUE dial, [INC]/[DEC] or [0] [9] (numeric keys).
fig.1-16

You can use the numeric keys to specify non-numerical settings for some parameters. * For the procedure of using the Numeric Keys to enter the characters or symbols in a name, refer to Assigning a Name (p. 46).

Performance/Patch/Rhythm Set Group


In the PLAY displays of Performance mode/Patch mode/ Rhythm Set mode, you can use the numeric keys to specify groups. To specify the group, hold down [SHIFT] and press numeric keys to specify groups. * Each parameter has a specific range, so you cannot set any value smaller than the minimum value or greater than the maximum value. Buttons [SHIFT]+[1] [SHIFT]+[2] [SHIFT]+[3] [SHIFT]+[4] [SHIFT]+[5] [SHIFT]+[6] Group PR-A (preset A) PR-B (preset B) PR-C (preset C) PR-D (GM (General MIDI)) PR-E (preset E) USER (user)

VALUE Dial
Rotating the VALUE dial clockwise increases the value, counterclockwise decreases the value. Holding down [SHIFT] as you move the VALUE dial increases value increments so you can make large value changes faster.

Restoring a Previous Value (Undo)


If you wish to restore a value to its immediate previous value, press [UNDO/COMPARE] to return the value to its pre-modified state. The Undo function can be used when modifying sound source settings.

[INC] and [DEC]


Pressing [INC] increases the value, and [DEC] decreases it. Keep [INC] or [DEC] pressed for continuous adjustment. For faster value increases, keep [INC] pressed down and press [DEC]. For decreasing value faster, keep [DEC] pressed down and press [INC]. If you press [INC] or [DEC] while holding down [SHIFT], the value increments will get bigger.

45

Chapter 1

A symbol appearing in the upper right of the display indicates that there are other items in this page that the screen has no room to show. Press [ ] to see these items, and press [ ] to return to the previous display.

Chapter 1. Overview of the XP-30

s Assigning a Name
The XP-30 lets you assign names to Patches, Performances, and Rhythm Sets. The procedure is the same for any type of data. To assign a name, use [ ]/[ ] to move the cursor to the location where you wish to input a character. Then use the VALUE dial or [INC]/[DEC] or the Numeric Keys to input a character. Available characters/symbols: space, AZ, az, 09, + - * / | = ! ? < > ( ) [ ] : ; . , ` # % &$@^_

Using the Numeric Keys


The numeric keys are used to input the numerals printed on each key as well as the characters assigned to each key (see the table below). Each time you press a numeric key, the display will cycle through the numeral and characters printed above the key. To specify a lowercase character, hold down [SHIFT] as you press the numeric key. Numeric Key [1] [2] [3] [4] [5] [6] [7] [8] [9] [0] Character ABC DEF GHI JKL MNO PQR STU VWX YZ! space

Convenient Functions
While you are holding down [SHIFT], the screen will show three functions that are convenient when entering a name. To use each function, hold down [SHIFT] and press the appropriate function button.
fig.1-17

A a: switch between uppercase/lowercase characters INS: insert a space at the cursor location DEL: delete the character at the cursor location

46

Chapter 2. Playing
Playing in Patch Mode
Patches are what you normally play during a performance. Select a Patch before playing. 1. Press [PATCH] to call up the PATCH PLAY display.
fig.2-01.e

Patch number Patch group Patch name

s Selecting a Patch
The 768 patches of the XP-30 are organized into six groups of 128 patches: User, and Preset AE. In addition, the patches of three popular Wave Expansion Boards (Session, Orchestral, and Techno Collection) are also stored onboard. Furthermore, you can install up to two separately available Wave Expansion Boards, which will allow you to choose from as many as 2044 patches. 2. Rotate the VALUE dial or press [INC]/[DEC] to select a Patch.

Selecting a Patch Using Numeric Keys


You can use numeric keys to directly select a desired Patch. 1. Press [PATCH] to call up the PATCH PLAY display.

The XP-30s user memory contains 128 Patches that can be rewritten to create your own Patches.

Button [SHIFT] + [1] [SHIFT] + [2] [SHIFT] + [3] [SHIFT] + [4] [SHIFT] + [5] [SHIFT] + [6] [EXP A] [EXP B] [EXP C] [EXP D] [EXP E]

Patch Group PR-A (Preset A) PR-B (Preset B) PR-C (Preset C) PR-D (GM (General MIDI)) PR-E (Preset E) USER (User) XP-A (Session) XP-B (Orchestral) XP-C (Techno Collection) XP-D (Wave Expansion Board D) XP-E (Wave Expansion Board E)

PR-AC, E (Presets AC, E)


The XP-30 includes 512 preset Patches that are not userrewritable. But you can call up preset Patch settings into the temporary area, modify them, and then store them in User memory.

PR-D (GM (General MIDI))


GM Patches are for instruments compatible with the GM System. The aim of this system is to standardize MIDI specifications among different equipment makers or models. The XP-30 contains 128 GM Patches that are not userrewritable. But you can call up GM Patch settings into the temporary area, modify them, and then store them in User memory.

3. Use numeric keys to input a Patch number. The patch number and name will blink. At this time, the Patch selection has not yet been finalized. 4. Press [ENTER] to finalize the entry.

XP-AC (Internal Wave Expansion)


The patches of three Wave Expansion Boards (766 patches) are already built into the XP-30, and cannot be rewritten. However you may modify the settings of the currently selected patch, and then store the modified patch in User memory.

XP-D, E (Wave Expansion Boards installed in EXP-D, E Slots)


The Patches included in optional Wave Expansion Boards are not user-rewritable. But you can call up those Patch settings into the temporary area, modify them, and then store them in User memory. * A Patch XP-D, E cannot be accessed if the Wave Expansion Board it belongs to has not been installed.

47

Chapter 2

USER

2. Press the following buttons to select a Patch group.

Chapter 2. Playing

Express Patch Select (Digit Hold)


With the Digit Hold function turned on, the 100s position and 10s position will be fixed when the numeric keys are used to select a Patch. This means that the numeric keys will only change the 1s position, and you wont have to press [ENTER] for each selection. The same applies to selecting Performances and Rhythm Sets. 1. Hold down [SHIFT] and press [ENTER] to turn on Digit Hold.
fig.2-02

Selecting Patches by Category (Patch Search Function)


The XP-30 provides a Patch Search function which allows you to specify a type (category) of Patch so that you can quickly find the desired Patch. There are a total of 38 categories. 1. Press [PATCH] to call up the PATCH PLAY display. 2. Press [CATEGORY] to turn the Patch Search function is on. The patch number display will change to the category display. * Now you can select patches within the currently selected category either by rotating the VALUE dial or by using [INC]/ [DEC]. To change the category group, use the numeric keys. If you wish to select patches from a different category, continue with the following procedure. 3. Hold down [CATEGORY] and press a key [0][9] (numeric keys) to select the category group.
fig.2-03

The numbers in the 100s position and 10s position will be displayed in a smaller size to indicate Digit Hold is on. 2. When you enter a numeric key number, the 1s position will change immediately without having to press [ENTER]. 3. To turn off Digit Hold, hold down [SHIFT] and press [ENTER] once again.

4. Rotate the VALUE dial or press [INC]/[DEC] to select a Category. The selected category display will blink. At this time, the selected category has not yet been finalized. * Now if you press [ ] the following display will appear, and you can select patches while viewing the number of patches (a) included in the currently selected category, and the order of this patch among the patches (b) that were selected after the search. To change the category, use the numeric keys.
fig.2-04

(b)

(a)

5. Press [ENTER] to finalize the entry. * In step 4, you can also select a category directly by pressing the corresponding numeric key. 6. Rotate the VALUE dial or press [INC]/[DEC] to select a Patch. 7. Press [CATEGORY] to turn the Patch Search function is off. You will return to the normal PATCH PLAY screen.

48

Chapter 2. Playing

The following categories can be selected.


Category Group --Piano PNO EP Keys&Organ KEY BEL MLT ORG ACD HRM Guitar AGT EGT DGT Bass BS SBS Orchestral STR ORC HIT WND FLT Brass BRS SBR SAX Synth HLD SLD TEK PLS FX SYN Pad BPD SPD VOX Ethnic PLK ETH FRT Rhythm&SFX PRC SFX BTS DRM CMB PLUCKED ETHNIC FRETTED Plucked (Harp etc.) Other Ethnic Fretted Inst (Mandolin etc.) Percussion Sound FX Beat and Groove Drum Set Other Patches which use Split and Layer BRIGHT PAD SOFT PAD VOX Bright Pad Synth Soft Pad Synth Vox, Choir HARD LEAD SOFT LEAD TECHNO SYNTH PULSATING SYNTH FX OTHER SYNTH Hard Synth Lead Soft Synth Lead Techno Synth Pulsating Synth Synth FX (Noise etc.) Poly Synth AC.BRASS SYNTH BRASS SAX Acoustic Brass Synth Brass Sax STRINGS ORCHESTRA HIT&STAB WIND FLUTE Strings Orchestra Ensemble Orchestra Hit, Hit Winds (Oboe, Clarinet etc.) Flute, Piccolo BASS SYNTH BASS Acoustic & Electric Bass Synth Bass AC.GUITAR EL.GUITAR DIST.GUITAR Acoustic Guitar Electric Guitar Distortion Guitar KEYBOARDS BELL MALLET ORGAN ACCORDION HARMONICA Other Keyboards (Clav, Harpsichord etc.) Bell, Bell Pad Mallet Electric and Church Organ Accordion Harmonica, Blues Harp AC.PIANO EL.PIANO Acoustic Piano Electric Piano Category NO ASSIGN Contents No assign

s Using Phrase Preview to Play Patches


The XP-30 allows you to preview Patches by hearing a phrase appropriate for each type of Patch. 1. Select a Patch (p. 47). 2. Press and hold [PHRASE PREVIEW]. * When a Performance is selected, the Patch of the Part for which settings are being made will sound. When a Rhythm Set is selected, a drum phrase will sound. * Patches of the USER group or from an optional Wave Expansion Board (SR-JV80 series) may not sound at the appropriate pitch range. In this case, use [+OCT] or [-OCT] (the Octave Shift function) to set an appropriate pitch range. * If the range of the phrase is wider than the range of the Tones within the Patch (p. 70), or wider than the range of the Parts within the Performance (p. 83), the portion of the phrase that exceeds the range will not sound. 3. The phrase will stop playing when you take your finger off [PHRASE PREVIEW]. 4. Hold down [SHIFT] and press [PHRASE PREVIEW], and the PREVIEW SELECT display will appear. Here you can specify how the phrase will be played (Mode), and select the phrase that will play (Patch Category).
fig.2-05

5. To specify how the phrase will be played, use the cursor buttons to move the cursor to the Mode parameter. 6. Rotate the VALUE dial or press [INC]/[DEC] to make the setting.

Mode (Preview Sound Mode)


SINGLE: The notes specified by Note 14 parameter (SYSTEM/PREVIEW/PREVIEW KEY) will sound successively one by one. CHORD: The notes specified by Note 14 parameter (SYSTEM/PREVIEW/PREVIEW KEY) will sound simultaneously. PHRASE: The phrase prepared for the Patch type (category) will sound. * This setting is linked with the Mode parameter (SYSTEM/ PREVIEW/PREVIEW MODE). 7. If you set the Mode parameter to PHRASE, you can specify the phrase that will sound. Use the cursor buttons to move the cursor to the Patch Category parameter. * If a rhythm set is selected, this will be fixed at DRUMS, and it will not be possible to change the phrase that is played.

PERCUSSION SOUND FX BEAT&GROOVE DRUMS COMBINATION

49

Chapter 2

Chapter 2. Playing

8. Rotate the VALUE dial or press [INC]/[DEC] to make the setting. For details on the available categories, refer to page 49. * This setting is linked with the Category parameter (PATCH/ COMMON/PATCH CATEGORY).

s Creating Smooth Pitch Changes (Portamento)


Portamento ensures a smooth pitch changeover from one note to the next note played. When [SOLO] is on (indicator lights), you can simulate techniques like violin glissandos. 1. Make sure that the PATCH PLAY display is showing. 2. Press [PORTAMENTO]. Its indicator lights. Youre ready to play portamento. * This setting is linked with the Sw parameter (PATCH/ CONTROL/PORTAMENTO). 3. To change the portamento settings, press [EDIT] to make the indicator light. Then press the [CONTROL] function button, and press [ ] or [ ] to access the PORTAMENTO display.
fig.2-06

s Making a Patch Sound Thick or Thin (Turning a Tone On/Off)


Since a Patch is a combination of up to four Tones, you can switch unwanted (Tones out of the four) off and get just the sound of a specific Tone. * This setting is linked with the Switch parameter (PATCH/ WAVE/WAVE). If you want just one or two Tones to sound in a Patch, turn the others off and store that setting on a Patch. This cuts nonessential use of the XP-30s simultaneous voices. 1. Make sure that the PATCH PLAY display is showing. 2. Make sure that [EDIT] indicator is dark. If it is lit, press [EDIT]. At this time, the on/off setting of each Tone in the displayed Patch will be shown by the indicators of TONE SWITCH [1] [4]. Those that are lit are on, and those that are dark are off. 3. Use TONE SWITCH [1][4] to switch Tones on/off.

4. Move the cursor over to Time, Mode, Type or Start parameter. See p. 73 for each parameters functions. 5. Rotate the VALUE dial or press [INC]/[DEC] to get the value you want. 6. Press [EXIT] to return to the PATCH PLAY display and play. * If you press [PORTAMENTO] when Single Performance is selected, the Portamento function can be switched on or off for the current Part. When Layer Performance is selected, the Portamento function can be switched on or off for the Parts with the Local parameter (PERFORM/MIDI/MIDI) set ON. If a Rhythm Set is selected, [PORTAMENTO] cannot be turned on.

s Playing Single Notes (Solo)


Normally, the XP-30 allows you to play chords. Pressing [SOLO] allows performance using single notes. This function is effective when performing a solo using single-note Patches like sax and flute. 1. Make sure that the PATCH PLAY display is showing. 2. Press [SOLO] so its indicator lights. Now you can play a solo. * This setting is linked with the Assign parameter (PATCH/ CONTROL/KEY MODE & BENDER). When the [SOLO] indicator is turned on, the Assign parameter will be set to SOLO. When the indicator is dark, it will be set to POLY. 3. Play the XP-30 keyboard. * If you press [SOLO] when Single Performance is selected, the Solo function can be switched on or off for the current Part. When Layer Performance is selected, the Solo function can be switched on or off for the Parts with the Local parameter (PERFORM/MIDI/MIDI) set ON. If a Rhythm Set is selected, [SOLO] cannot be turned on.

s Using the Sliders to Modify the Sound in Realtime (Sound Palette Function)
With the four sliders in the PALETTE section, you can create sound variations or volume changes in real time. * Sound variations or volume changes made with the Sound Palette affect only the performance. They have no effect on current Patch settings. Change the Patch and these Sound Palette settings will be lost. * The sound character and volume changes created using the Sound Palette will also be transmitted to the external MIDI devices.

50

Chapter 2. Playing

Changing Sound Characters


1. Make sure that the PATCH PLAY display is showing. 2. Press [FILTER/ENV] and its indicator lights. 3. Move the sliders while you play to vary the sound. To modify the brightness, move the CUTOFF slider. To change resonance, move the RESO. slider. To change attack time, move the ATTACK slider. To change decay time, move the DECAY slider.

s Selecting a Performance
The XP-30 offers three groups of Performances (User, Presets A and B) with each group having 32 Performances. A total of 96 Performances is available.

USER
The XP-30 user memory includes 32 Performances that can be rewritten to produce your own Performances.

PR-AB (Preset AB)


The XP-30 contains 64 preset Performances that cannot be rewritten. But you can call up preset Performance settings into the temporary area, modify them, and then store them in user memory.

Changing the Volume of Each Tone


1. Make sure that the PATCH PLAY display is showing. 2. Press [LEVEL] and its indicator lights. 3. Move the LEVEL slider as you play the keyboard to adjust volume as desired. Sliders 1, 2, 3, and 4 are used to change the volume of Tones 1, 2, 3, and 4, respectively.

fig.2-07.e

Performance number Performance group Performance name

Playing in Performance Mode


There are two types of performances: Layer performances and Single performances. The upper right of the display will indicate LAYER p* (* is the part number) for a layer performance, and part=* (* is the part number) for a single performance. Layer Performance allows playing two or more Parts simultaneously on the keyboard. Select Layer Performance if you want fat, rich sounds of two or more Patches, or play different Patches in a split keyboards different sections. Single Performance plays only the Part shown in the display (current Part). Select Single Performance for playing a song using two or more instruments. * Make your Performance type selection with the Key Mode parameter (PERFORM/COMMON/PERFORM COMMON). The Key Mode parameter determines how the XP-30 keyboard will play the internal sound source. It has no effect on how the XP-30 sound source is played from the built-in sequencer or an external MIDI device. * You can toggle between SINGLE and LAYER directly from the PERFORM PLAY display by pressing [SOLO] while holding down [SHIFT]. 2. Rotate the VALUE dial or press [INC]/[DEC] to select a Performance.

Selecting a Performance Using Numeric Keys


You can choose a Performance with direct numeric key input. 1. Press [PERFORM] to call up the PERFORM PLAY display. 2. Use the following buttons to select the Performance group. Button [SHIFT] + [1] [SHIFT] + [2] [SHIFT] + [6] Performance Group PR-A (Preset A) PR-B (Preset B) USER (User)

3. Use numeric keys to input the Performance number. The performance number and name will blink. At this time the Performance has not yet been finalized. 4. Press [ENTER] to finalize the entry. * Using Digit Hold, a Performance can be selected simply by specifying the 1s place number (p. 48).

51

Chapter 2

1. Press [PERFORM] to call up the 52 PERFORM PLAY display.

Chapter 2. Playing

s Playing Fatter and Richer Sounds by Combining Patches (Layer)


If a Layer Performance is selected, you can play all Parts with the Local parameter ON. Combining the Parts will produce, thicker, fatter sounds.
fig.2-08.e

s Splitting the Keyboard to Play Separate Patches in Different Sections (Split)


If youve selected a Layer Performance, you can split the keyboard to play separate Patches with different sections of the keyboard. As the note range that plays each Part can be specified individually, you can split the keyboard into a maximum of 16 sections. For instance, you can play strings in the lower note section, piano in the higher note section and both sounds in the middle note section.
fig.2-09.e

Part 1

Part 2

Part 15 Part 16

Local parameters

1. Make sure that PERFORM PLAY display is showing. 2. Make sure that the upper right of the display indicates LAYER p* (* is the part number). If the display indicates part=* (* is the part number), the performance is a single performance, so hold down [SHIFT] and press [SOLO] to change to a layer performance. * The setting here is linked to the Key Mode parameter (PERFORM/COMMON/PERFORM COMMON). 3. Press the function button for the part that you wish to play, to make the indicator light. When the [1-8/9-16] indicator is dark, parts 18 can be selected, and when the [1-8/9-16] indicator is lit, parts 916 can be selected. The Local parameter of the selected part will be ON. * This setting is linked with the Local parameter (PERFORM/ MIDI/MIDI). 4. Repeat step 3 to turn the Local parameter ON for each part that you wish to play.

Part 1: Strings Part 1 + Part 2: (Strings + Piano) Part 2: Piano

* If a KEY RANG display (PATCH/COMMON) has been set, sounds are produced in the overlapping sections between the key ranges specified for the Patch and Performance. 1. Make sure that the PERFORM PLAY display is showing. 2. Make sure that the upper right of the display indicates LAYER p* (* is the part number). If the display indicates part=* (* is the part number), the performance is a single performance, so hold down [SHIFT] and press [SOLO] to change to a layer performance. * The setting here is linked to the Key Mode parameter (PERFORM/COMMON/PERFORM COMMON). 3. Press the function button for the part that you wish to play, to make the indicator light. When the [1-8/9-16] indicator is dark, parts 18 can be selected, and when the [1-8/9-16] indicator is lit, parts 916 can be selected. The Local parameter of the selected part will be ON. * This setting is linked with the Local parameter (PERFORM/ MIDI/MIDI). 4. Repeat step 3 to turn the Local parameter ON for each part that you wish to play. 5. Press [EDIT] to make the indicator light. Then press the [COMMON] function button, and press [ ] or [ ] to access the PERFORM COMMON display.

52

Chapter 2. Playing

6. Make sure that the Key Range parameter is ON. If it is OFF, use the cursor buttons to move the cursor to the Key Range parameter, and rotate the VALUE dial or press [INC]/[DEC] to turn it ON. * If the Key Range parameter is OFF, the keyboard cannot be split even when you set the key range. 7. Press [ ] to access the KEY RANG display.
fig.2-10

s Playing Along with a Song Playback (XP-30 Used as a Multitimbral Sound Source)
When a Single Performance is selected, the XP-30s keyboard will play only the Part you selected from the keyboard, convenient when you play the keyboard along with a song playback.
fig.2-11.e

Part 1

Part 2

Part 15 Part 16

8. Press [EDIT] to make the indicator go dark. 9. Press a function button to select the part whose Local parameter you wish to turn ON. When the [1-8/9-16] indicator is dark, you can select parts 18. When the [18/9-16] indicator is lit, you can select parts 916. 10. Specify the range of notes for which the part will sound. Use the cursor buttons to move the cursor to the Lower parameter and set the lowest note of the range. Move the cursor to the Upper parameter and set the highest note of the range. 11. Rotate the VALUE dial or press [INC]/[DEC] to specify the range of notes. * By specifying sections for different Parts so that they overlap each other, you can combine two or more Patches only in a specific section. 12. When you are finished making settings, press [EXIT] to return to the PERFORM PLAY display, and begin playing.

Selecting a Part You Want to Play on the Keyboard


If a Single Performance is selected, press [ ] or [ ] to select the Part you want to play. The selected Part is called the Current Part. 1. Make sure that the PERFORM PLAY display is showing. 2. Press [ ] or [ ] to choose the Part to be played. The part number shown in the upper right of the display will change.
fig.2-12

* You can also press a function button to select the part that you wish to play. At this time, the function button indicator of the selected part will light.

Muting a Specific Part (Turning Receive Channel On/Off)


While you play along with the playback of a song, you can turn on/off any specific Part. This allows you to turn off the melody Part for karaoke applications or for practicing the muted Part. 1. Make sure that [EDIT] indicator is dark. If it is lit, press [EDIT] to turn it off. At this time, the function button indicators will indicate the on/ off status of each Part. When [1-8/9-16] indicator is dark, the function button indicators will indicate the status of Parts 1-8. When [1-8/9-16] indicator is lit, the function button indicators will indicate the status of Parts 9-16. Lit is on, and dark is off. 2. Hold down [SHIFT] and press the function button to switch Parts on/off. * This setting is linked with the Rx parameter (PERFORM/ MIDI/MIDI).

53

Chapter 2

Chapter 2. Playing

s Assigning a Different Patch to a Part


The Patch assigned to each Part can be stored as a Performance parameter. 1. Make sure that the PERFORM PLAY display is showing. 2. Press [ ] or [ ] to choose the Part to which you want to assign a different Patch. 3. While holding down [PERFORM], press [PATCH] to call up the PLAY display (PART PLAY) of the Patch assigned to a specific Part.
fig.2-13

3. Move the sliders while you play the XP-30s keyboard to vary the sound. To change brightness, move the CUTOFF slider. To change resonance, move the RESO slider. To change attack time, move the ATTACK slider. To change decay time, move the DECAY slider.

Changing the Level (Volume) of Each Part


1. Make sure that the PERFORM PLAY display is showing. 2. Press [LEVEL] to light its indicator. 3. Press [ ] or [ ] to select the Part whose level (volume) you want to change. If youve selected any of Parts 14, sliders 1, 2, 3, and 4 adjust Parts 1, 2, 3, and 4, respectively. If youve selected any of Parts 58, sliders 1, 2, 3, and 4 adjust Parts 5, 6, 7, and 8, respectively. If youve selected any of Parts 912, sliders 1, 2, 3, and 4 adjust Parts 9, 10, 11, and 12, respectively. If youve selected any of Parts 1316, sliders 1, 2, 3, and 4 adjust Parts 13, 14, 15, and 16, respectively. 4. Move the slider as you play to adjust the level (volume) of each Part as desired.

The upper right of the display will indicate the number of the currently selected part (the current part). 4. Use the same procedure as in Patch mode to select a Patch (p. 47). * This setting is linked with the Group parameter and Number parameter (PERFORM/PART/PATCH). 5. Press [PERFORM] or [EXIT] to return to the PERFORM PLAY display.

s Using the Sliders to Modify the Sound in Realtime (Sound Palette Function)
Using the Sound Palette function, you can modify sound characters of the Patch assigned to a Part or adjust the volume level of each Part. * Sound variations or volume changes made with the Sound Palette function affect only the performance. They have no effect on the currently selected Performance, so the Sound Palette settings cannot be saved. If you change the Performance, these settings will be lost. * The sound character and volume changes created using the Sound Palette will also be transmitted to the external MIDI devices.

Changing Sound Characters


* If Single Performance is selected, the effect applies only to the current Part. With Layer Performance selected, this affects only the Parts with Local parameter (PERFORM/MIDI/MIDI) set ON. 1. Make sure that the PERFORM PLAY display is showing. 2. Press [FILTER/ENV] to light its indicator.

54

Chapter 2. Playing

Playing in Rhythm Set Mode


In Rhythm Set mode, you can play percussion instruments (Rhythm Tones) on the keyboard. As the Rhythm Tone assigned to each key varies by the Rhythm Set selected, you can play a wide range of percussion instruments.

1. Press [RHYTHM] to call up the RHYTHM PLAY display.


fig.2-14.e

Rhythm Set number Rhythm Set group Rhythm Set name

s Selecting a Rhythm Set


The XP-30 contains a total of twelve rhythm sets, organized into six groups (User and Preset AE) with two rhythm sets in each group. In addition, the rhythm sets of two popular Wave Expansion Boards (Session and Techno Collection) are onboard. Furthermore, you can install up to two separately sold Wave Expansion Boards, giving you access to an even larger number of percussion instruments.

2. Rotate the VALUE dial or press [INC]/[DEC] to select a Rhythm Set. * Here, pressing [0] (on the numeric key) while holding down [CATEGORY] takes you to the display shown below, where you can verify the total number of selectable Rhythm Sets (a), and the number within the sequence of the currently selected Rhythm Set (b), and choose a Rhythm Set.
fig.2-14a

USER
The XP-30s user memory contains two Rhythm Sets that can be rewritten to make up your own Rhythm Sets.
(b) (a)

PR-AC, E (Preset AC, E)


The XP-30 includes eight preset Rhythm Sets that are not user-rewritable. But you can call up preset Rhythm Set settings into the temporary area, modify them, and then store them in user memory.

Selecting a Rhythm Set Using Numeric Keys


Using numeric keys, you can direct input a desired Rhythm Set. 1. Press [RHYTHM] to call up the RHYTHM PLAY display. 2. Press the following buttons to select a Rhythm Set group. Button [SHIFT] + [1] [SHIFT] + [2] [SHIFT] + [3] [SHIFT] + [4] [SHIFT] + [5] [SHIFT] + [6] [EXP A] [EXP C] [EXP D] [EXP E] Rhythm Set Group PR-A (Preset A) PR-B (Preset B) PR-C (Preset C) PR-D (GM (General MIDI)) PR-E (Preset E) USER (User) XP-A (Session) XP-C (Techno Collection) XP-D (Wave Expansion Board D) XP-E (Wave Expansion Board E)

PR-D (GM (General MIDI))


GM Rhythm Sets are for instruments compatible with the General MIDI System intended to standardize MIDI specifications among different equipment makers or models. The XP-30 offers two GM Rhythm Sets that are not userrewritable. But you can call up GM Rhythm Set settings into the temporary area, modify them, and then store them in user memory.

XP-A and C (Internal Wave Expansion)


The rhythm sets of two Wave Expansion Boards (16 rhythm sets) are already built-in, and cannot be rewritten. However, you can modify the settings of the currently selected rhythm set, and then save the modified settings in User memory.

XP-D, E (Wave Expansion Boards installed in EXP-D, E Slots)


These Rhythm Sets are included in optional Wave Expansion Boards and are not user-rewritable. But you can call up Rhythm Set settings into the temporary area, modify them, and then store them in user memory. * A Patch XP-D, E cannot be accessed if the Wave Expansion Board it belongs to has not been installed.

3. Use numeric keys to input a Rhythm Set number. The rhythm set number and name will blink. At this point the Rhythm Set has not yet been finalized. 4. Press [ENTER] to finalize the entry. * Using Digit Hold, a Rhythm Set can be selected simply by specifying the 1s place number (p. 48).

55

Chapter 2

Chapter 2. Playing

s Playing Percussion Instruments


1. Press [RHYTHM] to call up the RHYTHM PLAY display. 2. Select a desired Rhythm Set. 3. Press a key on the keyboard to play a percussion instrument. The key (Note name) you press and its percussion instrument name (Rhythm Tone name, the same as the Wave it uses) will be displayed below the Rhythm Set name.
fig.2-15.e

Playing an Arpeggio
The XP-30s Arpeggiator lets you produce an arpeggio (broken chord) simply by playing a chord. In addition to normal arpeggios, you can also accurately simulate guitar cutting or strumming techniques depending on the Arpeggiator settings. The Arpeggiator can in fact be used as a handy automatic arranger. By pressing [ARPEGGIO], the indicator lights and allows playing arpeggios from the XP-30 keyboard. * If you press [ARPEGGIO] to turn this function on when Single Performance is selected, the current Part will play arpeggios. When a Layer Performance is selected, an arpeggio will sound for the Part specified by the Part parameter (SYSTEM/ ARPEGGIO/ARPEGGIO). * The arpeggios played by the arpeggiator are also transmitted from the MIDI OUT connector to external MIDI devices. 1. Make sure that the PLAY display of the sound source mode (PERFORM, PATCH, RHYTHM, GM) is displayed. 2. Press [ARPEGGIO] to turn the Arpeggiator on. 3. If you wish to change how the arpeggio is played, hold down [ARPEGGIO] to access the ARP SELECT display, move the cursor to the Style parameter, and change the setting.
fig.2-16

Note name

Rhythm Tone name

You can also use the TONE SELECT buttons to select the displayed key. [TONE SELECT 1]: move to an octave lower key [TONE SELECT 2]: move to the semitone below [TONE SELECT 3]: move to the semitone above [TONE SELECT 4]: move to an octave higher key * When you want to play the percussive instrument sound assigned to the B1 key, first push [-OCT] once, then press the B2 key. Similarly, push [+OCT] once then press the C#6 or D6 key to play the percussive instrument sound assigned to the C#7 or D7 key. (On the XP-30, the leftmost white key is C2, and rightmost white key is C7.) For details, refer to Transposing the Keyboard in Octave Units (Octave Shift) (p. 59).

* The selection you make here will also affect the Style parameter (SYSTEM/ARPEGGIO/ARPEGGIO) settings. There are 43 arpeggio styles available. For selection, refer to the following guideline.

Playing an Arpeggio According to the Timing Interval of a Note


1/41/32

Playing a Glissando
GLISSANDO

Playing a Bass Part


SYNTH BASS, SLAP BASS A, SLAP BASS B, WALK BASS

Playing a Guitar
RHYTHM GTR A, RHYTHM GTR B, RHYTHM GTR C, RHYTHM GTR D, RHYTHM GTR E, 3FINGER GTR, STRUMMING GTR

Playing a Keyboard Instrument


KBD COMPING A, KBD COMPING B

Playing a Waltz
KBD COMPING C, KBD COMPING D

56

Chapter 2. Playing

Playing in Reggae Style


KBD COMPING E

s Playing an Arpeggio Over a Preset Keyboard Area


As soon as you press [ARPEGGIO] to turn the Arpeggiator on, the keyboard will be set to play arpeggios so conventional keyboard playing is no longer possible. If you split the keyboard into two different areas, you can use one area for normal playing and the other for playing arpeggios. This setting, for instance, allows you to play arpeggios with the left hand and a melody with the right hand. 1. Press [PERFORM] to call up the PERFORM PLAY display.

Playing Percussion Instruments


PERCUSSION * There are also other styles besides the above, including those used for random play and for creating your own styles. For details regarding each style, refer to Arpeggio Settings (ARPEGGIO) (p. 108). 4. To change the groove feel of the arpeggio, hold down [ARPEGGIO] to access the ARP SELECT display, move the cursor to the Accent parameter, and change the setting.
fig.2-16a

A setting of 100% will produce the most pronounced groove feel. * This setting will also affect the Accent Rate parameter (SYSTEM/ARPEGGIO/ARPEGGIO) settings. 5. To change the range in which the arpeggio is played, hold down [ARPEGGIO] to access the ARP SELECT display, move the cursor to the Oct parameter, and change the setting.
fig.2-17

3. Make sure that the Key Range parameter (PERFORM/ COMMON/PERFORM COMMON) is ON. If it is OFF, turn it ON (p. 53). 4. Set the Local parameter (PERFORM/MIDI/MIDI) ON for the Part you want to hear (p. 52). 5. After pressing [SYSTEM] to make the indicator light up, press the [ARPEGGIO] function button followed by [ ] to display an Arpeggio screen like the one shown below.
fig.2-18

If you want the arpeggio to sound using only the notes that you actually play, set this to 0. With a +1 setting, arpeggio will take place over a range up to 1 octave higher than the notes you play. A -1 setting will result in arpeggio occurring over the range down to 1 octave lower than the notes you play. * This setting will also affect the Octave Range parameter (SYSTEM/ARPEGGIO/ARPEGGIO) settings. 6. To change the tempo in which the arpeggio is played, hold down [ARPEGGIO] to access the ARP SELECT display, move the cursor to the Tempo parameter, and change the setting.
fig.2-17a

6. Use the cursor buttons to move the cursor to the Part parameter. 7. Rotate the VALUE dial or press [INC]/[DEC] to set the part that will play the arpeggio. 8. Set the Lower or Upper parameter (PERFORM/ COMMON/KEY RANG) to specify the note range of the part that will play the arpeggio (p. 53). 9. Set the key range of parts other than the arpeggio part so that they do not overlap the range in which the arpeggio is played. 10. After you finish settings, press [EXIT] to call up the PERFORM PLAY display again and play a chord. * If you play an arpeggio using Layer Performance but without setting key range, the chords will sound for all Parts except for the specified Part.

* This setting will also affect the Tempo parameter (SYSTEM/ ARPEGGIO/ARPEGGIO) settings. 7. Play a chord to produce an arpeggio. 8. To stop the arpeggio, press [ARPEGGIO] to turn off the indicator. * If you hold down [SHIFT] when you press [ARPEGGIO], the ARP SELECT display will continue being displayed, without you having to hold down [ARPEGGIO]. To go back to the previous display, press [EXIT].

57

Chapter 2

2. If you have selected a Single Performance, set the Key Mode parameter (PERFORM/COMMON/PREFROM COMMON) to LAYER (p. 52).

Chapter 2. Playing

s Holding an Arpeggio
If you hold down [ARPEGGIO] and press [TRANSPOSE], and get the indicator to start blinking, the arpeggio will continue to be played even if you release the chord. 1. Hold down [ARPEGGIO] and press [TRANSPOSE] to make the indicator blink. 2. Play a chord. 3. If you play a different chord or notes while the arpeggio is being held, the arpeggio will change accordingly. 4. To cancel Arpeggio Hold, hold down [ARPEGGIO] and press [TRANSPOSE] simultaneously once again.

s Playing an Arpeggio from an External MIDI Device


The XP-30 can also produce arpeggios with incoming Note messages from an external MIDI device. 1. Connect the XP-30s MIDI IN connector and the MIDI OUT connector of an external MIDI device with a MIDI cable. 2. Press [PERFORM] to call up the PERFORM PLAY display. 3. Press [SYSTEM] to make the indicator lit, press the [MIDI] function button, and then press [ ] to access the PERFORM MIDI display.
fig.2-19

Using a Hold Pedal


If you play an arpeggio while pressing the hold pedal, the arpeggio will continue to be played even if you release the chord. 1. Connect an optional pedal switch to the HOLD PEDAL jack. 2. Play a chord while pressing the hold pedal. 3. To play another chord, release the pedal, press it again as you play the next chord.

4. Use the cursor buttons to move the cursor to the Remote parameter. 5. Rotate the VALUE dial or press [INC]/[DEC] to turn the setting ON. 6. Play the external MIDI device.

s Creating an Arpeggio Pattern


There are a total of 9 parameters that can be set for the Arpeggiator, but the most important is the Style parameter setting. The arpeggio pattern is largely determined by this setting. When you set the Style parameter, the Motif, Beat Pattern, Accent Rate and Shuffle Rate parameters will automatically be set to optimum settings. After selecting the style, you can also set Octave Range and Key Velocity parameters, etc. If this selection does not provide the pattern you want, modify the settings of the Motif, Beat Pattern, Accent Rate and Shuffle Rate parameters to add variations to the style as desired. * Motif, Beat Pattern, Accent Rate and Shuffle Rate settings will be lost if you select another style and then turn the power off. * The values you can set with the Motif or Beat Pattern parameters are normally limited by the selected style. Only when the Style parameter is set to LIMITLESS will all values be acceptable.

s Simulating a Guitar Cutting Technique


You can simulate a guitar cutting technique by following the procedure below. By using the Sound Palette, it is also possible to apply a wah effect as you play. 1. Select a guitar Patch. 2. Set the Style parameter (SYSTEM/ARPEGGIO/ ARPEGGIO) to RHYTHM GTR B, RHYTHM GTR C, RHYTHM GTR D or RHYTHM GTR E. 3. Press [FILTER/ENV] so the indicator lights. 4. Move the CUTOFF slider or RESO slider while you play a chord.

58

Chapter 2. Playing

1. Press [SYSTEM] to make the indicator lit, and then press the [ARPEGGIO] function button to access the ARPEGGIO display.
fig.2-20

Convenient Functions for Performance


s Transposing the Keyboard in Octave Units (Octave Shift)
The Octave Shift function transposes the pitch of the keyboard in 1 octave units (-3 +3 octaves). For playing a bass part more easily using your right hand, transpose the keyboard down by 1 or 2 octaves. 1. Press [+OCT] or [-OCT] and its indicator will light. Pressing [+OCT] once will raise the keyboard 1 octave and pressing [-OCT] once will lower it 1 octave. The specified Octave Shift setting will be shown in the center=C4 indication of each Play screen. For example if you press [+OCT] once to raise the keyboard one octave, the display will indicate center=C5. This means that when you press the C4 key, the C5 note will sound.
fig.2-21

* For details regarding each parameter, refer to Arpeggio Settings (ARPEGGIO) (p. 108) 2. Move the cursor to Style and specify the style you want. 3. Move the cursor to Octave Range and specify the key range over which you want arpeggio. 4. Press [ ], move the cursor to Motif, and specify the order in which the notes of the chord will be sounded. * The available choices depend on the Style parameter setting. For details, refer to Arpeggio Style List (p. 182). 5. Move the cursor to Beat Pattern to change the beat (rhythm). * The available choices depend on the Style parameter setting. For details, refer to Arpeggio Style List (p. 182). 6. Press [ ], move the cursor to Accent Rate, and specify the groove ratio. A 100% setting will result in the most pronounced groove feel. 7. Move the cursor to Shuffle Rate and specify the swing rate. With a setting of 50%, the notes will be spaced evenly. As the value increases, the note timing will have more of a swing feel. 8. Press [ ], move the cursor to Key Velocity, and specify the strength with which the notes of the chord will be sounded. Move the cursor to Key Velocity and specify the force of the chord. When REAL is selected, the velocity at which the notes are actually played will be used. With a setting of 1127, the specified velocity value will be used regardless of the force with which you play the chord. 9. If you want to play an arpeggio using Layer Performance, move the cursor to Part and specify the Part for which you want arpeggio. * Parts other than that specified here will not sound as arpeggios, and the notes of the chord will sound as you play. 10. Move the cursor to Tempo and specify the speed of an arpeggio. 11. After you finish settings, press [EXIT].

* There is only one Octave Shift setting in the XP-30 so it remain valid even if you select a different Patch, Performance or Rhythm Set or turn power off. 2. To turn off the Octave Shift function, press the other button [+OCT] or [-OCT] of that pressed in step 1 the same number of times. The indicator will go off.

59

Chapter 2

Chapter 2. Playing

s Transposing the Keyboard in Semitone Steps (Transpose)


Transpose changes keyboard pitch in units of semitones (-5 +6 semitones). This function is useful when you play transposed instruments such as trumpet or clarinet following a printed score. 1. Press [TRANSPOSE] to light indicator. This turns Transpose on. 2. While holding down [TRANSPOSE], press [+OCT] or [OCT] to transpose the keyboard. Pressing [+OCT] once while holding down [TRANSPOSE] will raise the keyboard one semitone. Pressing [-OCT] once while holding down [TRANSPOSE] will lower the keyboard one semitone. The specified Transpose setting will be added to the Octave Shift value. For example, if you hold down [TRANSPOSE] and press [+OCT] once to raise the keyboard a semitone, the display will indicate center=C#4. So when C4 is pressed, the C#4 note will sound. 3. To turn off Transpose, press [TRANSPOSE] once again so that its indicator goes off. The Transpose setting you make will be maintained. * The Transpose setting you make here will also change the Transpose parameter (SYSTEM/CONTROL/KEYBOARD). * The setting you make will be maintained even if you select a different Patch, Performance or Rhythm Set, or turn the power off.

s If Stuck Notes Occur or a Note Does Not Sound (Panic)


If a note played on the XP-30 or from an external device locks or keeps sounding and you cant shut it off, hit the Panic button. Do the same if a note does not sound.

When Stuck Notes Occur


1. Hold down [SHIFT] and press [EXIT]. MIDI messages for Note Off and Hold Off will be transmitted to the Parts (MIDI channels) receiving Note On/ Hold On messages. 2. The display will indicate Panic! Now Muting. while the Panic function is being executed. When this message goes off, you can start playing.

When a Note Does Not Sound


1. Hold down [SHIFT] and press [EXIT] for more than a second. MIDI messages for Volume (127), All Note Off, Pitch Bend (center), Channel Aftertouch (0), Modulation (0), and Hold 1 (0) will be transmitted to all Parts (MIDI channels). 2. The display will indicate Panic! Now Transmitting. while the Panic function is being executed. When this message goes off, you can start playing.

60

Chapter 3. Creating Your Own Sounds


Regarding Effects
The XP-30 contains three independent effects units.

In Performance Mode/GM Mode


The Multi-Effects, Chorus and Reverb effects can be set individually for each Performance and GM mode. The intensity of each effect will be set for each Part (Fig. 1), but the Send Level setting for each Tone can also influence effect intensity (Fig. 2). Effects settings of the Patch assigned to each Part will be ignored, but Multi-Effects applied to a Patch assigned to a given Part can also be applied to the entire Performance.
fig.3-02.e

Multi-Effects (EFX)
The Multi-Effects offers 40 different effects ranging from single effects such as distortion and delay to powerful combination effects. The Multi-Effects also includes chorus and reverb effects which are independent of the Chorus and Reverb outlined below.

Chorus
Chorus adds depth and spaciousness to the sound.

Fig.1 When Output Assign is set to EFX in the Performance mode (the output settings for Tone are ignored)
Performance
Part 1 Patch Part16

Reverb
Reverb adds reverberation characteristics of hall or auditorium ambiences. Connection of the three effects units depend on the mode youve selected.

TONE

Multi-Effects Chorus Reverb

In Patch Mode
The Multi-Effects, Chorus and Reverb effects can be set individually for each Patch. Adjusting the signal level to be sent to each effects unit (Send Level) provides control over the effect intensity thats applied to each Tone.
fig.3-01 fig.3-03.e

Fig.2 When Output Assign is set to PATCH in the Performance mode (the output settings for Tone are valid)
Performance
Part 1

Patch
Part16

Patch

TONE

Multi-Effects Chorus Reverb

TONE

Multi-Effects

Chorus

Reverb

In Rhythm Set Mode


Because in Rhythm Set mode, only Part 10 of a Performance is called up, the effects settings of a Performance in the temporary area will be used.

61

Chapter 3

s How Effects Units Work in Different Modes

Chapter 3. Creating Your Own Sounds

s Turning Effects On/Off


Built-in effects units (Multi-Effects, Chorus and Reverb) can be turned on/off for the XP-30 as a whole. Turn them off if you want to edit sound while listening to the original sound or if you want to use external effects units. 1. Press [EFFECTS ON/OFF] to call up the EFFECTS ON/ OFF display.
fig.3-04

Sound Editing Procedures


With the XP-30, you have total control over various settings. Each item to be set is a parameter. Editing refers to modifying any parameter value. This section goes over editing procedures for Patches, Performances and Rhythm Sets.

s Editing a Patch
Start by editing a preexisting Patch to create a new one. Since a Patch is a combination of up to any four Tones, you should listen to how the individual Tones sound before you edit.

2. Press [ ] or [ ] to move the cursor to the effect that you wish to modify. 3. Rotate the VALUE dial or press [INC]/[DEC] to switch it on/off. 4. When you finish making settings, press [EFFECTS ON/ OFF] or [EXIT] to return to the previous display. * When the EFX (multi-effects), Chorus, and Reverb processors are all off, the [EFFECTS ON/OFF] indicator goes out, showing that the onboard effects processors are not used.

Four Tips for Editing Patches


Start with a Patch thats somewhat familiar sounding Its hard to create a new sound thats exactly what you want if you just select a Patch and modify its parameters at random. It makes sense to start with a Patch whose sound is related to what you have in mind. Deciding on the Tone to use When creating a Patch, deciding on the Tones youll use is crucial. For each Tone, use the TONE SWITCH [1][4] to decide whether to turn it on (have it sound) or off. Turn off Tones you dont need to avoid using more voices than required. A Tone switches on/off each time its respective button is pressed. When a Tones indicator lights, itll sound. Check the Structure setting The important Type parameter (PATCH/COMMON/ STRUCT) determines how the four Tones combine. Before editing Tones, make sure you really understand how they work together. Turn off effects Since XP-30 effects really influence the sound, turn them off to listen to the sound itself so you can better evaluate the changes youre making. Sometimes just changing effects settings can give you the sound you want.

62

Chapter 3. Creating Your Own Sounds

1. Press [PATCH] to access the PATCH PLAY display, and select the Patch whose settings you wish to modify (p. 47). 2. Press [EDIT] to make the indicator light. 3. Use the function buttons to select the display group. The button indicator of the selected display group will blink.
fig.3-05

An asterisk (*) will be displayed at the left of the Patch group. This shows Patch settings have been modified.
fig.3-07

* If you select another Patch in the group with an asterisk (*), the modified Patch settings will be lost. If you wish to keep these modified settings, you must write them into user memory (p. 68).

Editing Patches Using the Palette Display


4. Use [ ] or [ ] to select a display page. 5. If you have selected a parameter display that can be set independently for each Tone, the number of the Tone selected for editing will be shown in the display. To select a different Tone, press [EDIT] to temporarily turn off the indicator, and use TONE SELECT [1][4] (located in the row of function buttons) to select a Part.
fig.3-06

When editing a Tone in a Patch, the parameter values of the four Tones can be displayed together on a single display called the Palette display. Use it when you want to modify parameter values as you compare the settings of the four Tones. 1. When modifying a Tone, use [ ] or [ ] to move the cursor to the parameter you wish to modify. 2. Press [PALETTE EDIT] to call up the Palette display.
fig.3-08

For simultaneously modifying the same parameter for two or more Tones, hold down one of TONE SELECT [1][4] buttons and press another TONE SELECT [1][4] button, then another if so desired. An asterisk (*) will be indicated for Tones other than the first-selected Tone. * To switch Tones on/off, turn off [EDIT] indicator and then use the TONE SWITCH [1][4] located in the row of function buttons. 6. Use [ ] or [ ] to move the cursor to the parameter you wish to modify. 7. Use the VALUE dial, [INC]/[DEC] or numeric keys and modify the parameter value. * If youve selected two or more Tones, your editing will modify the parameter values for all selected Tones by the same amount. * If youve made a mistake in setting the parameter value or you dont like the changes, just press [UNDO/COMPARE] to restore the value to what it was. 8. If you wish to move to another display group, press [EDIT] to make the indicator light, and use the function buttons. * You can also move to another display group by holding down [SHIFT] and using [ ] or [ ]. Since this can be done even when [EDIT] indicator is dark, it is a faster way to get around because you dont have to turn on [EDIT] indicator each time. 9. Repeat steps 38 to complete a Patch. 10. When you finish making settings, press [EXIT] or [PATCH] to return to the PATCH PLAY display.

3. Press a TONE SELECT [1][4] buttons, [ ] or [ ] to choose the Tone to modify. The button indicator for the selected Tone will light and the Tone number and Wave name appear in the display. For modifying the same parameter of two or more Tones simultaneously, hold down one of TONE SELECT [1][4] buttons and press another. 4. Use the VALUE dial, [INC]/[DEC] or numeric keys to change the parameter value. If youve selected two or more Tones, your editing will modify the parameter values for all selected Tones by the same amount. If you want to set all selected Tones to the same value, select the Tone having that value by pressing [ ] or [ ] and while holding down [SHIFT], press [ENTER]. * If youve made a mistake in setting the parameter value or you dont like the changes, press [UNDO/COMPARE] to restore the value to what it was. 5. If you wish to edit other parameters, press [ ] or [ ] to select the parameter that you wish to edit. 6. Repeat steps 35 to complete a Patch. 7. To cancel the palette display, press [PALETTE EDIT] to make the button indicator go dark.

63

Chapter 3

Chapter 3. Creating Your Own Sounds

Note on Tone Editing


Because the XP-30 is designed to create wholly realistic sounds, editing necessarily affects the complex PCM waveforms sound are based on. So if you try to create a sound which is totally different from the original waveform, the results may not be what you want. XP-30 waveforms are divided into: One-Shot: These waveforms contain sounds that have short decays. A one-shot waveform records the initial rise and fall of the sound. Some of the XP-30s one-shot waveforms are sounds that are complete in themselves, such as percussive instrument sounds. The XP-30, however, contains many other one-shot waveforms that are only partial elements of sounds. These include attack components such as piano hammer sounds and guitar fret noises. Looped: These waveforms contain sounds with long decays or sustained sounds. With looped waveforms, the latter part of the sound is generated repeatedly over a specified portion of the waveform for as long as the note is held (allowing wave memory to be used more efficiently). The XP-30s looped waveforms include such sound components as piano string vibrations and hollow sounds of brass instruments. The following diagram shows an example of sound (electric organ) that combines one-shot and looped waveforms.
fig.3-09.e

Notes for Editing Looped Waveforms


With many acoustic instruments like piano and sax, radical timbral changes occur during the first few moments of the note. This initial attack is what defines much of the instruments character. The XP-30 provides a variety of waveforms containing realistic acoustic instrument attacks. To obtain the maximum realism when using these waveforms, it is best to leave the filter wide open during the attack. This way, all the complex timbral changes can be heard. For the decay portion of the sound, you can use the envelope to produce the desired changes. If you use the envelope to modify the attack portion as well, the natural attack contained in the waveform itself will not be heard to full advantage, and you may not achieve the result you want.
fig.3-10.e

Looped Portion Tone change stored with the wave

Envelope for the TVF filter

Resulting tone change

TVA ENV for looped Organ waveform (sustain portion)

TVA ENV for one-shot Keyclick waveform (attack portion)

Resulting TVA ENV change

+
Key-off

=
Key-off

Notes for Editing One-Shot Waveforms


An envelope cannot be used for giving a one-shot waveform a longer decay than the original waveforms, or make it a sustaining sound. Even if you were to make such envelope settings, you would simply be controlling a non-existent portion of the sound, so such settings would have no meaning.

If you try to make just the attack brighter and subdue just the decay using the TVF filter, you need to keep in mind the timbral characters of the original waveform. And particularly if youre making a part of the sound brighter than the original waveform, you should first generate upper harmonics (not present in the original waveform) using Color and Depth parameters (PATCH/WAVE/FXM) before filtering. If you dont, the results will be disappointing. To make the entire sound brighter than the original waveform, try adjusting effects such as enhancer and equalizer before modifying the TVF parameter (PATCH/TVF).

64

Chapter 3. Creating Your Own Sounds

s Editing a Performance
Start with an existing Performance and edit it to create a new Performance. But before you do, try to envision what the entire Performance will sound like and decide which Patch to assign to each of 16 Parts. 1. Press [PERFORM] to access the PERFORM PLAY display, and select the Performance whose settings you wish to modify (p. 51). 2. Press [EDIT] to make the indicator light. 3. Use the function buttons to select the display group. The button indicator of the selected display group will blink.
fig.3-11

An asterisk (*) will be displayed at the left of the Performance group. This shows Performance settings have been modified.
fig.3-13

* If you select another Performance in the group with an asterisk (*), the modified Performance settings will be lost. If you wish to keep these modified settings, you must write them into user memory (p. 68).

Editing Performance Using the Palette Display


You can also edit a Performance using the Palette display in Performance mode. When modifying Part settings for a Performance, the values for eight Parts (Part 18 or Part 916) will be displayed together on a single display. This is useful when you wish to change parameter values while comparing each Part settings.

4. Use [ ] or [ ] to select a display page. 5. If you have selected a parameter display that can be set independently for each Part, the number of the Part selected for editing will be shown in the display. To select a different Part, press [EDIT] to temporarily turn off the indicator, and use [1-8/9-16] and the function buttons to select a Part.
fig.3-12

2. Press [PALETTE EDIT] to call up the Palette display.


fig.3-14

6. Use [ ] or [ ] to move the cursor to the parameter you wish to modify. 7. Use the VALUE dial, [INC]/[DEC] or numeric keys and modify the parameter value. * If youve selected two or more Tones, your editing will modify the parameter values for all selected Tones by the same amount. * If youve made a mistake in setting the parameter value or you dont like the changes, just press [UNDO/COMPARE] to restore the value to what it was. 8. If you wish to move to another display group, press [EDIT] to make the indicator light, and use the function buttons. * You can also move to another display group by holding down [SHIFT] and using [ ] or [ ]. Since this can be done even when [EDIT] indicator is dark, it is a faster way to get around because you dont have to turn on [EDIT] indicator each time. 9. Repeat steps 38 to complete a Performance. 10. When you finish making settings, press [EXIT] or [PERFORM] to return to the PERFORM PLAY display. 3. Press [ ] or [ ] to choose the Part to modify. The Part number and the Patch name assigned to the Part will be shown in the display. * To switch between the palette page for parts 18 and the palette page for parts 916, press [1-8/9-16]. 4. Use the VALUE dial, [INC]/[DEC] or numeric keys to change the parameter value. * If youve made a mistake in setting the parameter value or you dont like the changes, press [UNDO/COMPARE] to restore the value to what it was. 5. If you wish to edit other parameters, press [ ] or [ ] to select the parameter that you wish to edit. 6. Repeat steps 35 to complete a Performance. 7. To cancel the palette display, press [PALETTE EDIT] to make the button indicator go dark.

65

Chapter 3

1. When modifying a Part, use [ ] or [ ] to move the cursor to the parameter you wish to modify.

Chapter 3. Creating Your Own Sounds

Modifying the Patch Assigned to a Part


When using Patches in Performance mode, some settings such as effects settings will be affected by Performance settings. If you wish to edit a Patch while hearing how it will sound in the Performance, use this procedure: 1. Make sure that the PERFORM PLAY display is showing. 2. Press [ ] or [ ] to select the Part to which the selected Patch is assigned. 3. While holding down [PERFORM], press [PATCH]. Both button indicators will light. This will call up the PLAY display of the Patch assigned to the currently selected Part.
fig.3-15

4. Use [ ] or [ ] to select a display page. 5. If you have selected a parameter display that can be set independently for each key, the key selected for editing will be shown in the display. To select a different key, play the desired key on the keyboard.
fig.3-17

* If [EDIT] indicator is turned off, you can also use the TONE SELECT [1][4] (located in the row of function buttons) to select the displayed key. TONE SELECT [1]: move to an octave lower key TONE SELECT [2]: move to the semitone below TONE SELECT [3]: move to the semitone above TONE SELECT [4]: move to an octave higher key 6. Use [ ] or [ ] to move the cursor to the parameter you wish to modify. 7. Use the VALUE dial, [INC]/[DEC] or numeric keys and modify the parameter value. * If youve made a mistake in setting the parameter value or you dont like the changes, just press [UNDO/COMPARE] to restore the value to what it was. 8. If you wish to move to another display group, press [EDIT] to make the indicator light, and use the function buttons. * You can also move to another display group by holding down [SHIFT] and using [ ] or [ ]. Since this can be done even when [EDIT] indicator is dark, it is a faster way to get around because you dont have to turn on [EDIT] indicator each time. 9. Repeat steps 38 to complete a Rhythm Set. 10. When you finish making settings, press [EXIT] or [RHYTHM] to return to the RHYTHM PLAY display. An asterisk (*) will be displayed at the left of the Rhythm Set group. This shows Rhythm Set settings have been modified.
fig.3-18

4. The following steps are the same as when you modify a Patch in Patch mode. 5. When you finish making settings, press [EXIT] to call up the PLAY display of the Patch assigned to the Part. An asterisk (*) will be displayed at the left of the Patch group. This indicates the Patch settings have been modified. 6. To return to the PERFORM PLAY display, press [PERFORM] or [EXIT]. * If you select another Patch in the group with an asterisk (*), the modified Patch settings will be lost. To keep these modified settings, you must write them into user memory (p. 68).

s Editing a Rhythm Set


You can change the percussion instrument assigned to each key. As each percussion instrument consists of a single Rhythm Tone, there is no Palette display. 1. Press [RHYTHM] to access the RHYTHM PLAY display, and select the Rhythm Set whose settings you wish to modify (p. 55). 2. Press [EDIT] to make the indicator light. 3. Use the function buttons to select the display group. The button indicator of the selected display group will blink.
fig.3-16

* If you select another Rhythm Set in the group with an asterisk (*), the modified Rhythm Set settings will be lost. If you wish to keep these modified settings, you must write them into user memory (p. 68).

* Since Rhythm Sets do not have an LFO, it will not be possible to select the LFO group.

66

Chapter 3. Creating Your Own Sounds

Keeping Edited Sound


s Memory and Data Storage
The location where Patch and Performance settings, etc. are stored is Memory. There are three memory types: temporary memory, rewritable memory and non-rewritable memory.
fig.3-19.e

Rewritable Memory
System Memory
System memory stores system parameter settings that determine how the XP-30 functions. When you modify these settings, the system memory settings are rewritten directly. These settings are non-volatile, being retained even when the power is turned off.

Preset E (PR-E) Preset D (GM) Preset C (PR-C) Preset B (PR-B) XP-C Preset A (PR-A) XP-B Performance 32 Patch 128 Rhythm Set 2 XP-A Patch Rhythm Set

XP-30 Sound

User Memory
User memory contains data for 32 Performances, 128 Patches and two Rhythm Sets.

User (USER) Performance 32 Patch 128 Rhythm Set 2

Memory Card (optional: SmartMedia)


These are read/write cards which can store data from internal system memory and user memory. You can use memory cards to store data for which there is no room in internal user memory, or data which you wish to use on another XP-30. Before a memory card can be used, it must be formatted (p. 122). * Either S2M-5 or S4M-5 memory cards can be used. Memory cards are not included, but may be purchased from your dealer.

Write

Temporary Area

Load

Save Expansion Board

Non-Rewritable Memory
Preset Memory
Data in Preset memory (Patch: PR-AC, E, GM, XP-AC, Performance: PR-A, B, Rhythm Set: PR-AC, E, GM, XP-A, C) cannot be rewritten. However, you can call up settings from preset memory into the temporary area, modify them and then store the modified data in rewritable memory.

Data File (.SVD) Performance 32 Patch 128 Rhythm Set 2 System

EXP-E Slot (XP-E) EXP-D Slot (XP-D) Patch Rhythm Set

Memory Card

Temporary Memory
Temporary Area
This area holds data for the Performance, Patch, and Rhythm Set you select using the front panel buttons, etc. When you play the keyboard or play back an external sequence, sound is produced based on data in the temporary area. When you modify a Performance, Patch or Rhythm Set, you are modifying the data that has been called into the temporary area instead of the data in memory. Settings in the temporary area are temporary, and will be lost when the power is turned off or when you select another Performance/Patch/Rhythm Set. To keep the settings you have modified, you must write them into rewritable memory.

Wave Expansion Boards (optional: SR-JV80 Series)


Up to four Wave Expansion Boards can be installed in EXPD, E Slots in the XP-30. Wave Expansion Boards contain Wave data, as well as Patches and Rhythm Sets that use this Wave data, which can be called directly into the temporary area and played.

67

Chapter 3

Chapter 3. Creating Your Own Sounds

s Storing a Sound You Modify into User Memory


The modified settings you make are only temporary, and will be lost if you turn the power off or select another Patch, Performance or Rhythm Set. To keep the modified settings, you must write them into user memory. 1. In Patch mode (when storing a Patch), Performance mode (when storing a Performance) or in Rhythm Set mode (when storing a Rhythm Set), press [UTIL/CARD]. The UTIL 1 display will appear.
fig.3-20

Functions of Patch Parameters


fig.3-05

s Settings Common to the Entire Patch (COMMON)


On this display you can assign a name to a Patch and set the volume and pan of the entire Patch.

PATCH NAME
You can assign a name of up to 12 characters to the Patch. * For details on assigning names, refer to Assigning a Name (p. 46).

2. Use [ ] or [ ] to make 1: WRITE blink. Then press [ENTER]. The WRITE display will appear.
fig.3-21.e

PATCH CATEGORY
Category
Specify the type (category) of the Patch. The Patch Search function uses this setting. This setting also determines the phrase that will be sounded by the Phrase Preview function. * For details on the category names, refer to p. 49.

Writing destination

3. Use the VALUE dial, [INC]/[DEC] or numeric keys to specify the Patch, Performance or Rhythm Set number of the destination of writing. 4. Press [ENTER]. If Internal Write Protect is turned off, the specified writing destination Patch, Performance or Rhythm Set will be overwritten. 5. If Internal Write Protect (p. 121) is turned on, the following display will appear. Change the ON setting to OFF, and press [ENTER]. Internal Write Protect will be turned off, and you will return to the display of step 2. Press [ENTER] once again and the selected Patch will be overwritten.
fig.3-22

PATCH CLOCK
Some parameters allow you to set a time value in terms of a note length which is determined by a tempo setting or tempo source you specify; Rate parameters (PATCH/ LFO/ LFO1, 2), Time parameter (PATCH/WAVE/TONE DELAY), and some Multi-Effects parameters. This Patch Clock setting sets the tempo which can be used by these parameters. * When using a Patch in Performance mode, the setting of this parameter will be ignored, and the setting of the PERFORM CLOCK display (PERFORM/COMMON) will be used instead.

Source (Patch Clock Source)


Select the source of the Patch Clock. PATCH: Synchronize to the Patch Tempo setting. SYSTEM: Synchronize to the tempo clock of the sequencer. * The Patch Clock does not transmit clock messages from MIDI OUT connector.

* Internal Write Protect is automatically turned ON when the XP-30s power is turned on.

Tempo (Patch Tempo)


Set the Patch Tempo setting. * When Source (Patch Clock Source) is set to SYSTEM, synchronization will be according to the tempo clock of the system, so it will not be possible to set the tempo value. The tempo of the system will be displayed in parentheses ( ).

PATCH COMMON
Level
Adjust the volume level of the Patch.

68

Chapter 3. Creating Your Own Sounds

Pan
Adjust the stereo position of the Patch. A setting of L64 is far left, 0 is center, and 63R is far right.

Priority (Voice Priority)


Specify which currently-sounding notes will take priority when notes are turned off to make room for newly-requested notes that would exceed the limit of 64 simultaneous voices. LAST: Notes played later will take priority. When the 65th voice is requested, the first-played of the currently sounding notes will be turned off. LOUDEST: Louder notes will take priority. When the 65th voice is requested, the softest of the currently sounding notes will be turned off.

Analog Feel (Analog Feel Depth)


Adjust the depth at which 1/f modulation is applied to the Patch.

1/f Modulation
1/f is a mathematical ratio that expresses the amount of predictable randomness occurring in natural sounds that the human ear finds pleasing, such as soft breezes or gentle brooks. The XP-30 is able to modulate the pitch and volume of sounds by this ratio to create the warmth characteristic of early analog synthesizers.

VelRang (Velocity Range Switch)


Specify whether the Velocity Range setting (see following display) will be used or not. The Velocity Range setting will be used when the VelRange parameter is ON.

Octave (Octave Shift)


Specify the transposition of the Patch when played on the keyboard, in units of one octave (-3+3 octaves).

VELOCITY (Velocity Range)


These parameters specify the range of velocities that will play the Tone. This can be used to make notes of different strengths play different Tones. * To make Velocity Range settings, the Velocity Range Switch in the previous display must be turned ON.

Select the stretch tuning curve. The selected curve will affect the way in which notes of a chord sound with each other. The diagram below shows the tuning curves which can be selected. In the tuning curve, the horizontal axis represents the scale, and the vertical axis represents pitch difference relative to equal temperament. When OFF is selected for this parameter, the notes of the keyboard will be in mathematically equal temperament. With a setting of 3, the high and low note ranges will be stretched the most.
fig.3-23.e

Lower (Velocity Range Lower)


Specify the lower velocity limit. Although it also depends on the Cross Fade settings, notes played softer than this limit will not sound the Tone, or will produce extremely quiet sounds.

Upper (Velocity Range Upper)


Specify the upper velocity limit. Although it also depends on the Cross Fade settings, notes played more strongly than this limit will not sound the Tone, or will produce extremely quiet sounds. * It is not possible to set Lower to a value greater than Upper, nor Upper to a value less than Lower. If you attempt to do so, the two values will change together.

Pitch difference from equal temperament

Parameter value

3 2 1 OFF 1 2 3
Low note range High note range

OFF

Cross Fade (Velocity Cross Fade)


Specify the way in which the volume of the Tone will change when the velocity of a note falls outside of the specified Velocity Range. Higher settings will result in a more gradual change in volume. If you do not want the Tone to sound at all for velocities outside the specified range, set this parameter to 0.
fig.3-24.e

Level

Stretched Tuning
Acoustic pianos are normally tuned so that the high note range is a bit sharper and the low note range is a bit flatter than a mathematically calculated equal temperament (i.e., where each octave would be precisely double the frequency of the previous octave). This is done simply because pianos sound better when tuned this way.

Velocity Lower parameter value Upper parameter value

69

Chapter 3

Stretch (Stretch Tuning Depth)

Chapter 3. Creating Your Own Sounds

KEY RANG (Key Range)


These parameters specify the range of notes that will play the Tone. This can be used to make notes in different areas of the keyboard play different Tones.

fig.3-25e

TYPE 5 TONE 1 (3) WG TVA R TONE 2 (4)


fig.3-25f

TVF

Lower (Key Range Lower)


Specify the lowest note that will play the Tone. WG

TVF

TVA

Upper (Key Range Upper)


Specify the highest note that will play the Tone. * It is not possible to set Lower to a value greater than Upper, nor Upper to a value less than Lower. If you attempt to do so, the two values will change together. * If you have used Octave Shift (System) or the Transpose parameter (SYSTEM/CONTROL/KEYBOARD) to transpose the pitch of the XP-30s keyboard, the keyboard area specified by Key Range will also be shifted.

TYPE 6 TONE 1 (3) WG TVA R TONE 2 (4)


fig.3-25g

TVF

WG

TVF

TVA

TYPE 7 TONE 1 (3) WG TVF TVA R TONE 2 (4)


fig.3-25h

STRUCT (Structure)
Type (Structure Type)
The Structure parameter determines how Tones 1 and 2 (and 3 and 4) are connected.
fig.3-25a

WG

TVF

TVA

TYPE 1 TONE 1 (3) WG TVF TVA

TYPE 8 TONE 1 (3) WG TVF TVA R

TONE 2 (4)
fig.3-25b

WG

TVF

TVA

TONE 2 (4)
fig.3-25i

WG

TVF

TVA

TYPE 2 TONE 1 (3) WG TVA TVF

TYPE 9 TONE 1 (3) TVF TVA WG TVF TVA R

TONE 2 (4)
fig.3-25c

WG

TONE 2 (4)
fig.3-25j

WG

TVF

TVA

TYPE 3 TONE 1 (3) WG TVA TVF B TONE 2 (4)


fig.3-25d

TYPE 10 TONE 1 (3) TVF TVA WG TVF TVA R TONE 2 (4) WG TVF TVA

WG

TYPE 4 TONE 1 (3) WG TVA B TONE 2 (4) WG TVF TVA TVF

70

Chapter 3. Creating Your Own Sounds

The display will graphically indicate the selected Structure. The symbols displayed have the following meanings. W1 (WG1), W2 (WG2), F1 (TVF1), F2 (TVF2), A1 (TVA1), A2 (TVA2), B (booster), R (ring modulator) * If you select a Tone while in the Structure display, the Tone that is paired with the selected Tone will also be selected. * If a Structure 210 is selected, turning off one Tone will cause the other Tone to be connected in the simple order of WG/TVF/ TVA.

s Setting Effects for a Patch (EFFECTS)


This group contains settings for the Multi-Effects/Chorus/ Reverb effects used by a Patch. * If an x mark is displayed at the right of the display name, the effect for that display has been turned off. Turn the corresponding effect on before you make settings (p. 62).

OUTPUT
These parameters specify how the output of each Tone will be sent to the effects. * When the Type parameter (PATCH/COMMON/STRUCT) has a setting of 210, the outputs of Tones 1 (3) and 2 (4) will be combined with Tone 2 (4). This means that the setting for Tone 1 (3) will be ignored.

Booster (Booster Gain)


If the Type parameter has been set to 3 or 4, you can adjust how strongly the Booster will function. The Booster amplifies the incoming signal, causing it to distort. This creates an effect similar to the distortion often used on an electric guitar.

Output Assign (Output Assign/Output Level) Ring Modulator


The Ring Modulator multiplies two Tones together, creating a new sound that includes overtones (inharmonic overtones) that were not present in either of the two original Tones. Since the pitch difference between the two Tones will change the overtone structure, the result will be an unpitched metallic sound. This is especially suitable for creating bells and other metallic sounds.
fig.3-26

* If you select MIX, the settings in the PATCH EFX OUT display (PATCH/EFFECTS) will be ignored.

Chorus (Chorus Send Level)


Adjust the amount of Chorus for each Tone.

Reverb (Reverb Send Level)


Adjust the amount of Reverb for each Tone.

PATCH EFX TYPE


Specify the Patch Multi-Effects.

Type (EFX Type)


Select the type of Multi-Effects. For details refer to MultiEffects Types (EFX Parameter) (p. 93).

PATCH EFX PRM (Patch EFX Parameters)


Set the various parameters of the selected EFX type. For details refer to Multi-Effects Types (EFX Parameter) (p. 93).

71

Chapter 3

Select whether or not the output of each Tone will be sent through Multi-Effects, and adjust the volume of each Tone. MIX: Output the Tone to the OUTPUT jack without passing through Multi-Effects. EFX: Output the Tone to the OUTPUT jack through MultiEffects.

Chapter 3. Creating Your Own Sounds

PATCH EFX OUT (Patch EFX Output)


These parameters specify the output for the Tone for which EFX was selected in Output Assign. * For Tones which have an Output Assign setting of MIX, the settings of this display will be ignored.

PATCH CHORUS
These parameters control the Chorus effect of the Patch.

Rate (Chorus Rate)


Adjust the speed of modulation for the Chorus effect.

Depth (Chorus Depth)


Adjust the depth of modulation for the Chorus effect.

Mix Out (EFX Output Level)


Adjust the volume level of the original sound and the MultiEffects sound.

Delay (Chorus Pre Delay)


Adjust the time delay after the original sound begins until the Chorus effect begins to apply. Higher settings result in a more spacious effect.

Chorus (Chorus Send Level)


Adjust the amount of Chorus for the sound that passes through Multi-Effects.

Fbk (Chorus Feedback Level)


Adjust the amount of sound from the Chorus output that is returned (fed back) to the Chorus. Higher settings result in a more intense effect.

Reverb (Reverb Send Level)


Adjust the amount of Reverb for the sound that passes through Multi-Effects.

PATCH EFX CTRL (Patch EFX Control)


Use this setting when you wish to use a specific controller to control an EFX parameter. The EFX parameters available for control will depend on the selected EFX type. For details refer to Multi-Effects Types (EFX Parameter) (p. 93). The upper line of the display will show the EFX parameters that can be controlled. For each EFX parameter, you can specify the EFX Control Source and the EFX Control Depth.

Level (Chorus Level)


Adjust the volume of the Chorus effect.

Out (Chorus Output Assign)


Select the way in which the Chorus and Reverb are connected. MIX:
fig.3-27.e

The Chorus sound and the Reverb sound are mixed.

EFX Control Source 1, 2


The following MIDI controllers can be used. If you wish to use a controller that will apply to all Patches, or a controller that cannot be directly specified here, select SYS-CTRL1 or SYS-CTRL2, and then select the controller using the Control 1/2 parameter (SYSTEM/CONTROL/SYS-CTRL ASSIGN). OFF: controller not used SYS-CTRL1: System controller (control 1) SYS-CTRL2: System controller (control 2) MODULATION: Modulation (MIDI controller number 1) BREATH: Breath (MIDI controller number 2) FOOT: Foot (MIDI controller number 4) VOLUME: Volume (MIDI controller number 7) PAN: Pan (MIDI controller number 10) EXPRESSION: Expression (MIDI controller number 11) BENDER: Pitch bend AFTERTOUCH: Aftertouch

Chorus input

Reverb OUTPUT

Reverb input

Chorus

REV:Apply reverb to the chorus sound.


fig.3-28.e

Chorus input Chorus Reverb input Reverb OUTPUT

M+R: Mix the chorus sound to which reverb is not applied and the chorus sound to which reverb is applied.
fig.3-29.e

EFX Control Depth 1, 2


Adjust the amount of change that will occur in response to controller movements. Higher settings will result in greater change. Negative (-) settings will reverse the direction of change.

Reverb input

Chorus

Reverb

OUTPUT

Chorus input

72

Chapter 3. Creating Your Own Sounds

PATCH REVERB
These parameters control the Reverb effect of the Patch.

s Using Controllers to Change How Sounds Are Played (CONTROL)


The parameters in this group determine how the controllers will function.

Type (Reverb/Delay Type)


Select the type of Reverb effect. ROOM1: dense reverb with short decay ROOM2: sparse reverb with short decay STAGE1: reverb with greater late reverberation STAGE2: reverb with strong early reflections HALL1: reverb with clear reverberance HALL2: reverb with rich reverberance DELAY: a conventional delay PAN-DLY: a delay with echoes that move left and right

KEY MODE & BENDER (Key Assign Mode & Bender)


Assign (Key Assign Mode)
Specify how notes will be played. When playing a solo instrument Patch (such as sax or flute) it is effective to use a setting of SOLO. POLY: Two or more notes can be played simultaneously. SOLO: Only one note will sound at a time.

Time (Reverb/Delay Time)


Adjust the time of reverberation. If you have selected DELAY or PAN-DLY, this parameter will adjust the time delay from the original sound until the first echo will sound.

Legato (Solo Legato Switch)


Turn this parameter ON when you use Solo Legato, and OFF when you do not. Solo Legato is a function that works only when the Key Assign Mode is SOLO. When Solo Legato is ON, pressing a key while a previous key is already pressed will cause the note to change pitch to the pitch of the newly pressed key while continuing to sound. This is effective when you wish to simulate performance techniques such as a guitarists hammering on and pulling off.

Fbk (Delay Feedback Level)


Adjust the amount of delayed sound that is returned (fed back) to the delay. Higher values result in more delay repeats. * If you have selected any one of the Reverb types (ROOM1 HALL2), this parameter has no effect.

Bend Range
Specify the amount of pitch change that will occur when you move the Pitch Bend Lever. The left value specifies the pitch change that will occur when the lever is moved fully left. The right value specifies the pitch change that will occur when the lever is moved fully right. The left value has a range of -480 (-4 0 octaves), and the right value has a range of 0+12 (01 octaves).

HF Damp (Reverb/Delay HF Damp)


Adjust the frequency above which the reverberant sound will be cut. As the frequency is set lower, more of the high frequencies will be cut, resulting in a softer and more muted reverberance. If you do not want the high frequencies to be cut, set this parameter to BYPASS.

PORTAMENTO
Portamento is a function that causes the pitch to change smoothly from one note to the next played note. When the Key Assign Mode is SOLO, this is effective when simulating performance techniques such as a violinists glissando.

Level (Reverb/Delay Level)


Adjust the volume of the reverberant (or delayed) sound.

Sw (Portamento Switch)
Set this to ON when you wish to use Portamento.

Time (Portamento Time)


Adjust the time over which the pitch will change to the new pitch.

Mode (Portamento Mode)


Select the way in which Portamento will be applied. NORMAL: Portamento will always be applied. LEGATO: Portamento will be applied only for notes played legato (i.e., when you press the next key before releasing the previous key.

Type (Portamento Type)


Select the way in which the pitch difference between the two notes will be related to the time of movement. RATE: Time of movement will change in relation to the pitch difference. TIME: Time of movement will be constant, regardless of the pitch difference.

73

Chapter 3

Chapter 3. Creating Your Own Sounds

Start (Portamento Start Pitch)


Portamento will begin anew if you press another key during a pitch movement. This setting specifies how the new portamento will start. PITCH: Pitch will begin changing when the new key is pressed.
fig.3-30.e

Pan (Receive Pan Control Switch)


Specify how Pan messages will be received. OFF: Not received. CONT: Whenever a Pan message is received, it will immediately change the stereo location of the sound. KEY-ON: The stereo location of the sound will be changed when the next note is played. If a Pan message is received while a note is sounding, the current stereo location will not change until the next note. In this case, the stereo location will change only for the note played later, and the currently sounding note will not move.

Pitch

C5

D4 C4

Pitch Bend (Receive Pitch Bend Switch)


Time press D4 key press C5 key press C4 key

If you want Pitch Bend messages to be received, turn this parameter ON. If not, turn it OFF.

DAMPER
Specify how Hold 1 (sustain pedal) messages will be received by each Tone.

NOTE: Pitch will begin changing from the destination of the current movement.
fig.3-31.e

Pitch

Hold-1 RxSwitch (Receive Hold 1 Switch)


If you want Hold 1 messages to be received, turn this parameter ON. If not, turn it OFF.

C5

Redamper (Redamper Switch)


D4 C4

Time press D4 key press C5 key press C4 key

If a Hold 1 message is received during the time between a note-off (when you release the key) until when the sound disappears, the currently sounding sounds will be sustained if this Redamper setting is ON. If you use this function, you must also turn on the Receive Hold 1 switch.

PEAK & HOLD


Hold messages (Hold 1, Hold 2, Sostenuto, Soft) are used to sustain the sound. The XP-30 allows you to use these Hold messages to hold the values of specific parameters. * If you use this function, you must also turn on the Receive Hold 1 switch for the Patch (previous screen). * If you select HOLD for the following parameters, you must also set the Hold parameter (SYSTEM/CONTROL/CONTROL SOURCE) to the type of Hold message being controlled. * If you select PEAK for the following parameters, you must also set the Peak parameter (SYSTEM/CONTROL/CONTROL SOURCE) to the type of Hold message being controlled.

RxSWITCH (Receive Switch)


These parameters determine how Volume/Pan/Pitch Bend MIDI messages will be received by each Tone. * In general, Volume messages control the volume, Pan messages control the stereo location, and Pitch Bend messages control the pitch of. However the XP-30 allows you to use these MIDI messages to control other parameters that you specify. Thus, if you are using a message to control another (i.e., a non-standard) parameter, you should turn off reception for that MIDI message. If reception is turned on, that MIDI message will control its standard function in addition to the special assignment you have made.

Volume (Receive Volume Switch)


If you want Volume messages to be received, turn this parameter ON. If not, turn it OFF.

74

Chapter 3. Creating Your Own Sounds

EfxCtrl (EFX Control Peak/Hold)


Specify how Hold messages will affect the parameters you specify in the PATCH EFX CTRL display (PATCH/ EFFECTS). OFF: Parameter values will not be held even if Hold messages are received. HOLD: Parameter values will be held when Hold messages are received. PEAK: Parameter values will be held when Hold messages are received. However if a parameter value higher than the current one is received while Hold is still on, that new value will be held.

AFTERTOUCH: LFO1: LFO2: VELOCITY: KEYFOLLOW:

Aftertouch LFO1 rate LFO2 rate Velocity Key follow (adjust the parameter value depending on the keyboard location, relative to a standard value (0) at the C4 key) Playmate (adjust the parameter value depending on the time length that the key is pressed)

PLAYMATE:

Control 3 (Control Source 3)


Assign a controller to Control Source 3. The controllers available for selection are the same as for Control Source 2.

Ctrl 1 (Control 1 Peak/Hold)


Specify how Hold messages will affect the parameters controlled by Control Source 1 (Modulation: MIDI controller number 1). The settings are the same as for EFX Control.

CONTROL 13
Specify the parameters to be controlled by Control Sources 13 and the depth of each parameter. The upper line of the display will show the Control Source selected in the previous display.

Ctrl 2 (Control 2 Peak/Hold)


This parameter specifies the way in which Hold messages will control the parameter selected as Control Source 2 in the following display. The range of values is the same as for EFX control.

Ctrl 3 (Control 3 Peak/Hold)


This parameter specifies the way in which Hold messages will control the parameter selected as Control Source 3 in the following display. The range of values is the same as for EFX control.

Destination 14
Select the parameters to be controlled. Up to four parameters can be specified for each controller, and controlled simultaneously. OFF: no control PCH: WG Pitch CUT: TVF Cutoff Frequency RES: TVF Resonance LEV: TVA Level PAN: TVA Pan MIX: Output level of Tone CHO: Chorus Send level of Tone REV: Reverb Send level of Tone PL1: LFO1 depth of WG Pitch PL2: LFO2 depth of WG Pitch FL1: LFO1 depth of TVF Cutoff Frequency FL2: LFO2 depth of TVF Cutoff Frequency AL1: LFO1 depth of TVA Level AL2: LFO2 depth of TVA Level pL1: LFO1 depth of TVA Pan pL2: LFO2 depth of TVA Pan L1R: LFO1 rate L2R: LFO2 rate

CONTROL SOURCE
If you wish to use controllers to control a specific Tone parameter, select the controller in this display. Each Patch can have up to 3 control source assigned to it, but the function of control source 1 is fixed at Modulation (MIDI controller number 1).

Control 2 (Control Source 2)


Assign one of the following controllers to Control Source 2. If you want to use a controller that will be common to all Patches, or to use a controller that is not available for selection here, first select SYS-CTRL 1 or SYS-CTRL 2 then set the Control 1/2 parameter (SYSTEM/CONTROL/SYS-CTRL ASSIGN) to select the controller. OFF: a controller will not be used SYS-CTRL1: System controller (Control 1) SYS-CTRL2: System controller (Control 2) MODULATION: Modulation (MIDI controller number 1) BREATH: Breath (MIDI controller number 2) FOOT: Foot (MIDI controller number 4) VOLUME: Volume (MIDI controller number 7) PAN: Pan (MIDI controller number 10) EXPRESSION: Expression (MIDI controller number 11) BENDER: Pitch bend

Depth 14
Adjust the amount of change that will occur in response to controller movement. Higher value will cause greater change. Negative (-) values will reverse the direction of the change. For LFO rates, negative (-) values will lengthen the period (causing slower modulation), and positive (+) values will shorten the period (causing faster modulation).

75

Chapter 3

* From the PATCH PLAY display you can switch directly to the CONTROL1 display by pressing [CONTROLLER] while holding down [SHIFT].

Chapter 3. Creating Your Own Sounds

s Modifying Waveform (WAVE)


This group contains parameters related to the basic waveform (Wave) of the Tone.

Mode (Tone Delay Mode)


Select the way in which the Tone will sound. NORMAL: The Tone will sound after the specified Delay Time.
fig.3-32.e

WAVE
Group (Wave Group)
Select the Group of the Wave. INT-A, B: Internal A, B EXP-AE: Wave Expansion Boards AE * It is not possible to select a Group of a Wave Expansion Board that is not installed.

Delay Time press key release key

HOLD:

Number (Wave Number)


Select the Wave number. The name of the Wave will be displayed in parentheses ( ).
fig.3-33.e

If the key is pressed for longer than the specified Delay Time, the Tone will sound after the Delay Time. If the key is released earlier than the Delay Time, the Tone will not sound.

Gain (Wave Gain)


Adjust the gain (volume boost) of the Wave. The setting range is -6+12 dB, in steps of 6 dB. An increase of 6 dB doubles the gain. When using the Booster to distort the sound, it is effective to use the maximum Gain setting.
Delay Time release key press key

Delay Time press key

Tone does not sound release key

Switch (Tone Switch)


When you wish to use the Tone, set this ON. When not using the Tone, set this OFF. In order to make best use of the available number of simultaneous voices, unused Tones should be turned off. * When you use TONE SWITCH [1][4] to turn Tones on/off, this is the parameter that is being set. If 2 seconds or more pass before the next key is pressed, the Tone will sound after the Delay Time. If less than 2 seconds pass before the next key is pressed, that interval will become the Delay Time after which the Tone will sound. CLOCK-SYNC: Synchronize the Delay Time to either the Patch Tempo (PATCH/COMMON/PATCH CLOCK), the Performance Tempo (PERFORM/COMMON/PERFORM CLOCK), or the tempo clock of the XP-30s system. If you want to use a fixed tempo in Patch mode (Tempo parameter setting), set the Source parameter (PATCH/COMMON/ PATCH CLOCK) to PATCH and set the desired tempo. If you want to use the systems tempo clock in Patch mode, set the Source parameter (PATCH/COMMON/PATCH CLOCK) to SYSTEM. If you want to use a fixed tempo in Performance mode (Tempo parameter setting), set the Source parameter (PERFORM/COMMON/PERFORM CLOCK) to PERFORM and set the desired tempo. If you want to use the systems tempo clock in Performance mode, set the Source parameter (PERFORM/COMMON/ PERFORM CLOCK) to SYSTEM. PLAYMATE:

FXM (Frequency cross modulation)


FXM is a function that uses frequency modulation to add new harmonic components to the sound. It can be used as a simple ring modulator in order to add a metallic flavor.

Switch (FXM Switch)


When you wish to use FXM turn this ON. If not, turn it OFF.

Color (FXM Color)


Select one of four ways in which FXM will use frequency modulation.

Depth (FXM Depth)


Adjust the depth of the frequency modulation created by FXM.

TONE DELAY
This parameter produces a time delay from the moment the key is pressed (or released) until when the Tone begins to sound. Since you can adjust the timing of each Tone, you can create effects in which pressing a single key produces two or more sounds at different times. * If you do not wish to use Tone Delay, set Mode to NORMAL and Delay Time to 0.

76

Chapter 3. Creating Your Own Sounds

KEY-OFF-N:

The Tone will not sound while the key is being pressed, but will sound after the Delay Time when the key is released.

Time (Tone Delay Time)


Specify the time after when the Tone will sound when using Tone Delay. If PLAYMATE has been selected in Tone Delay mode, a setting of 64 will mean that the delay time will be set to the interval between the previous Note On and the current Note On. A setting of 127 will result in a time that is twice as long as for a setting of 64, and a setting of 32 will result in a time that is 1/2 as long. If the Tone Delay Mode is set to CLOCK-SYNC, the setting will be in quarter-note steps, and the corresponding note value symbol will also be displayed. This lets you specify the delay time in note lengths relative to the synchronization tempo. * If the Type parameter (PATCH/COMMON/STRUCT) is set to a selection of 210, the outputs of Tone 1 (3) and 2 (4) will be combined into Tone 2 (4). This means that the settings of Tone 1 (3) will be ignored.

fig.3-34.e

Delay Time press key release key

KEY-OFF-D:

The Tone will not sound while the key is being pressed, but will sound after the Delay Time when the key is released. However for this setting, the TVA envelope of the Tone will begin when the key is pressed, so in most cases only the decay portion of the sound will be heard.

fig.3-35.e

Delay Time press key release key

* If you have selected a Wave that is a decay-type sound (i.e., a sound that fades away naturally even if the key is not released), selecting KEY-OFF-N or KEY-OFF-D may result in no sound being heard. TEMPO-SYNC: If you select a Wave with tempo (BPM) being displayed, the Tone will synchronize to the tempo clock of the system regardless of which key is pressed. This is most effective when playing phrase loops in sync with the tempo of a song (p. 130). If you want to sync to the tempo of a system in Patch mode, set the Source parameter (PATCH/COMMON/PATCH CLOCK) to SYSTEM. If you want to sync to the tempo of a system in Performance mode, set the Source parameter (PERFORM/COMMON/ PERFORM CLOCK) to SYSTEM. * When TEMPO-SYNC is selected, pitch and FXM settings will be ignored. * When selecting TEMPO-SYNC, also set the Time parameter to 0. If other values are set, Tone Delay will be activated.

77

Chapter 3

Chapter 3. Creating Your Own Sounds

s Modulating Sounds (LFO)


The LFO (Low Frequency Oscillator) creates cyclic change. Each Tone has two LFOs, and these can be used to apply change to the WG Pitch/TVF Cutoff Frequency/TVA Level/ TVA Pan.

ExtSync (LFO External Sync)


Select how the LFO will be synchronized. OFF: Unsynchronized CLOCK: Synchronize the LFO to the Patch Tempo, Performance Tempo, or the tempo clock of the XP30s system. If you want to use a fixed tempo in Patch mode (Tempo parameter setting), set the Source parameter (PATCH/COMMON/PATCH CLOCK) to PATCH and set the desired tempo. If you want to use the systems tempo clock in Patch mode, set the Source parameter (PATCH/ COMMON/PATCH CLOCK) to SYSTEM. If you want to use a fixed tempo in Performance mode (Tempo parameter setting), set the Source parameter (PERFORM/COMMON/PERFORM CLOCK) to PERFORM and set the desired tempo. If you want to use the systems tempo clock in Performance mode, set the Source parameter (PERFORM/COMMON/PERFORM CLOCK) to SYSTEM.

How to Use the LFO


Applying LFO to the Pitch creates vibrato, applying it to TVF Cutoff Frequency creates wah, and applying it to TVA Level creates tremolo. When LFO is applied to the TVA Pan, the stereo location of the sound will change cyclically. Depending on the settings, LFO can be used to cyclically exchange two Tones. For example if you wish to shift back and forth between Tones 1 and 2, select the same LFO settings for both, but make LFO Depth settings of opposite polarity (+/-) for their TVA Level settings.

LFO1/LFO2
Since both LFOs have the same parameters, there are explained here together.

Mode (LFO Fade Mode)


Select how the LFO will be applied. ON-IN: The LFO will fade in after the key is pressed.
fig.3-37.e

Form (LFO Form)


Select the waveform of the LFO.
fig.3-36.e

TRI

SIN

SAW

SQR

high (more) WG Pitch / TVF Cutoff Frequency / TVA Level / TVA Pan

Delay Time

Fade Time

Depth

triangle wave

sine wave

sawtooth wave

square wave low (less)

key is pressed

TRP

S&H

RND

CHS

ON-OUT: The LFO will be immediately applied when the key is pressed, and will then fade out.
fig.3-38.e

high (more) trapezoidal wave sample & hold wave random wave chaos wave WG Pitch / TVF Cutoff Frequency / TVA Level / TVA Pan low (less)

Delay Time

Fade Time Depth

Key Sync (LFO Key Sync)


Specifies whether you want the LFO cycle to start in sync with the timing of a key press (ON) or not (OFF).

key is pressed

OFF-IN:
fig.3-39.e

The LFO will fade in after the key is released.


high (more) Delay Time Fade Time Depth

Rate (LFO Rate)


Adjust the modulation rate of the LFO. * If you have set the External Sync value to CLOCK, this parameter will indicate a note value in multiples of a quarter note, and the corresponding note value symbol will also be displayed. This allows you to set the LFO rate in terms of a note length in the synchronization tempo. * The Chaos waveform has no wavelength. When the Chaos waveform is selected, the Rate setting has no effect.

WG Pitch / TVF Cutoff Frequency / TVA Level / TVA Pan key is key is pressed released low (less)

78

Chapter 3. Creating Your Own Sounds

OFF-OUT:The LFO will be immediately applied when the key is pressed, and will begin fading out when the key is released.
fig.3-40.e

s Modifying Pitch (PITCH)


The parameters in this group affect the WG Pitch of each Tone.

high (more) WG Pitch / TVF Cutoff Frequency / TVA Level / TVA Pan key is pressed low (less)

Delay Time

Fade Time Depth

PITCH
Specify the basic pitch of each Tone.

Coarse (Coarse Tune)


key is released

Adjust the pitch in semitone steps (-4+4 octaves).

Fine (Fine Tune)


Adjust the pitch in 1-cent steps (-50+50 cents). * One cent is 1/100th of a semitone.

Delay (LFO Delay Time)


Adjust the time from when the key is pressed (or released) until the LFO begins to take effect. (Refer to the diagrams for Fade Mode.)

Random (Random Pitch Depth)


If you want the pitch of the Tone to change randomly each time the key is pressed, set the desired amount of pitch change here. If you do not want the pitch to change randomly, set this to 0. The value is in units of 1 cent.

Fade (LFO Fade Time)


Adjust the time over which the LFO rises to its full effect (or diminishes). (Refer to the diagrams for Fade Mode.)

Offset (LFO Offset)


Adjust the basic value of the LFO waveform upward or downward.

Keyfollow (Pitch Key Follow)


This parameter sets the amount of pitch change that will occur when you move one octave on the keyboard. If you want the pitch to change 1 octave when the keyboard position rises 1 octave (as on normal keyboard instruments), set this parameter to +100. If you want the pitch to rise 2 octaves when the keyboard position rises 1 octave, set this parameter to +200. Negative (-) settings will make the pitch become lower as you play up the keyboard. If you want all keys of the keyboard to produce the same pitch, set this parameter to 0.
fig.3-41.e +200 +150 +120 +100 +70 +50 +40 +30 +20 +10 0 10 30 50 70 100 C2 C3 C4 C5 C6 C7

LFO DEPTH 1:2


These parameters adjust the way in which the LFO affects each parameter. Two values are displayed for each parameter. The left one is for LFO1, and the right one is for LFO2.

Pitch (Pitch LFO Depth 1, 2)


Adjust how much the LFO will affect the WG Pitch.

TVF (TVF LFO Depth 1, 2)


Adjust how much the LFO will affect the TVF Cutoff Frequency.

Pitch

TVA (TVA LFO Depth 1, 2)


Adjust how much the LFO will affect the TVA Level.

Pan (Pan LFO Depth 1, 2)


Adjust how much the LFO will affect the TVA Pan.

Keyboard position

PCH ENVELOPE (Pitch Envelope)


These parameters determine how the Pitch Envelope affects the pitch.

Envelope Depth (Pitch Envelope Depth)


Adjust the amount of the Pitch Envelope. Higher settings will result in greater change. Negative (-) settings will invert the direction of the envelope.

79

Chapter 3

Chapter 3. Creating Your Own Sounds

Velocity Sens (Pitch Envelope Velocity Sensitivity)


Set this parameter when you want your keyboard playing dynamics to affect the amount of pitch change. For higher settings, there will be a greater difference between softly and strongly played notes. Negative (-) settings will invert the direction of change.

s Modifying the Brightness of Sound with a Filter (TVF)


The parameters in this group allow you to use the TVF (Time Variant Filter) to modify the frequency characteristics of the sound.

PCH TIME ENV (Pitch Time Envelope)


These parameters determine how keyboard playing dynamics will affect the times of the Pitch Envelope.

FILTER
These parameters are the TVF filter settings.

Type (Filter Type)


Select the filter type. OFF: filter not used. LPF (Low Pass Filter): Cut the frequencies above the Cutoff Frequency. This is the most common type of filter used in synthesizers. BPF (Band Pass Filter): Pass only the frequencies in the area of the Cutoff Frequency. HPF (High Pass Filter): Cut the frequencies below the Cutoff Frequency. PKG (Peaking Filter): Emphasize the frequencies in the area of the Cutoff Frequency.

V-T1 (Pitch Envelope Time 1 Velocity Sensitivity)


Use this parameter when you want keyboard playing dynamics (velocity) to affect T1 (time) of the Pitch Envelope. For higher settings, there will be a greater difference between softly and strongly played notes. For positive (+) settings, keyboard velocity will speed up the T1 time. For negative (-) settings, keyboard velocity will slow down the T1 time.

V-T4 (Pitch Envelope Time 4 Velocity Sensitivity)


Use this parameter when you want keyboard playing dynamics (velocity) to affect T4 (time) of the Pitch Envelope. For higher settings, there will be a greater difference between softly and strongly played notes. For positive (+) settings, keyboard velocity will speed up the T4 time. For negative (-) settings, keyboard velocity will slow down the T4 time.

Cut (Cutoff Frequency)


Set the frequency of the filter.

Time Keyfollow (Pitch Envelope Time Key Follow)


Use this parameter when you want the keyboard location of the note to affect the times (T2T4) of the Pitch Envelope. Higher settings of this parameter will cause greater time change relative to the envelope time at middle C (C4). Positive (+) settings will cause the time change to become shorter for notes to the right of middle C. Negative (-) settings will cause the time change to become longer for notes to the right of middle C.

Res (Resonance)
Emphasize the frequencies in the area of the Cutoff Frequency. For some settings, excessive levels can cause oscillation and distortion.
fig.3-43.e

LPF Level High


Frequency

BPF

HPF

PKG

PCH ENVELOPE (Pitch Envelope)


These parameters set the Pitch Envelope (the shape of the pitch change over time).
fig.3-42.e

T1 L1

T2

T3

T4

L3

Keyfollow (Cutoff Frequency Key Follow)


Time

Pitch key is pressed key is released L4

L2

T14 (Pitch Envelope Time 14)


Set the times over which the pitch will change from one point to the next.

Use this parameter when you want the Cutoff Frequency to be affected by the keyboard position. Higher values will result in greater change relative to middle C (C4). Positive (+) settings will make the Cutoff Frequency rise as you play further the right of the keyboard. Negative () settings will make the Cutoff Frequency fall.

EnvDepth (TVF Envelope Depth)


Adjust the depth of the TVF envelope. Higher settings will result in greater change. Negative (-) values will invert the envelope.

L1L4 (Pitch Envelope Level 14)


Set the amount of pitch change (relative to the basic pitch) for each point.

80

parameter value

Cutoff frequency

Low

Chapter 3. Creating Your Own Sounds

TVF VELOCITY
These parameters determine how keyboard velocity will affect TVF Envelope/Cutoff Frequency/Resonance.

TVF ENVELOPE
These parameters set the TVF envelope (the way in which the cutoff frequency will change over time).
fig.3-44.e

V-Sens (TVF Envelope Velocity Sensitivity)


Use this parameter when you want velocity to affect the TVF Envelope. Higher settings will result in a greater difference between strongly and softly played notes. Negative (-) settings will invert the effect.

T1 L1

T2

T3

T4

L2

L3 L4

Cutoff Frequency key is pressed

V-Curve (TVF Envelope Velocity Curve)


Select one of 7 types of curve with which velocity will affect the Cutoff Frequency. The curve is displayed graphically at the right of the value.

Time key is released

T1T4 (TVF Envelope Time 14)


Set the times over which the cutoff frequency will move from one point to the next.

V-Resonance (Resonance Velocity Sensitivity)


Use this parameter when you want velocity to affect the Resonance. Higher settings will result in a greater difference between strongly and softly played notes. Negative (-) settings will invert the effect.

L1L4 (TVF Envelope Level 14)


Set the cutoff frequency levels for each point, relative to the basic cutoff frequency.

TVF TIME ENV (TVF Time Envelope)


These parameters determine how keyboard velocity will affect the times of the TVF envelope.

s Changing the Sounds Volume and Stereo Location (TVA)


The TVA (Time Variant Amplifier) controls volume changes and stereo location.

V-T1 (TVF Envelope Time 1 Velocity Sensitivity)


Use this parameter when you want velocity to affect T1 (time) of the TVF envelope. Higher settings will result in a greater difference between strongly and softly played notes. If you want higher keyboard velocities to speed up the T1 time, use positive (+) settings. To slow down the T1 time, use negative (-) settings.

TVA
Level
Adjust the basic volume of the Tone. Use this parameter to adjust the volume balance between Tones.

V-T4 (TVF Envelope Time 4 Velocity Sensitivity)


Use this parameter when you want Key Off Velocity (the speed at which you release a key) to affect T4 (time) of the TVF envelope. Higher settings will result in a greater difference between quickly and slowly released notes. If you want a quicker release to speed up the T4 time, use positive (+) settings. To slow down the T4 time, use negative (-) settings.

Pan
Adjust the pan (stereo location) of the Tone. L64 is full left, 0 is center, and 63R is full right.

V-Sens (TVA Envelope Velocity Sensitivity)


Use this parameter when you want keyboard velocity to affect the amount of change produced by the TVA envelope. Higher settings will result in a greater difference between strongly and softly played notes. Negative (-) settings will invert the effect.

Time Keyfollow (TVF Envelope Time Key Follow)


Use this parameter when you want keyboard position to affect the times (T2T4) of the TVF envelope. Higher settings will result in greater changes relative to middle C (C4). Positive (+) settings will result in shorter times as you play toward the right of the keyboard. Negative (-) settings will conversely result in longer times.

V-Curve (TVA Envelope Velocity Curve)


Select one of 7 curves that will determine how keyboard playing dynamics will affect the TVA envelope. The selected curve will be displayed at the right of the numerical value.

81

Chapter 3

Chapter 3. Creating Your Own Sounds

BIAS
Use the Bias parameter when you want keyboard position to affect the TVA level.
fig.3-45.e

L or R values can be set, and this will reverse the left/right order of the panning. If you want to alternate the pan position of two Tones, set them to opposite L and R settings.

LOWER + Level
0
C-1

UPPER Level

TVA TIME ENV (TVA Time Envelope)


+ 0

These parameters determine how the keyboard will affect the time changes of the TVA envelope.
Key
G9

Key Bias Point


G9 C-1

Bias Point

V-T1 (TVF Envelope Time 1 Velocity Sensitivity)


Use this parameter when you want velocity to affect T1 (time) of the TVA envelope. Higher settings will result in a greater difference between strongly and softly played notes. If you want higher velocities to speed up T1 time, use positive (+) values. If you want higher velocities to slow down T1 time, use negative (-) values.

LOWER&UPPER + Level
0
C-1

+ 0

ALL Level

0 +

+ 0

Bias Point

G9

Key

C-1

Bias Point

G9

Key

V-T4 (TVA Envelope Time 4 Velocity Sensitivity) Bias (Bias Level)


Adjust the angle of the volume change that will occur in the selected Bias Direction. Higher settings will result in greater change. Negative (-) values will invert the change. Use this parameter when you want Key Off Velocity (the speed at which you release a key) to affect T4 (time) of the TVA envelope. Higher settings will result in a greater difference between quickly and slowly released notes. If you want a quicker release to speed up the T4 time, use positive (+) settings. If you want a quicker release to slow down the T4 time, use negative (-) settings.

Point (Bias Point)


Select the key at which the volume will begin to change.

Direction (Bias Direction)


Select the direction in which change will occur starting from the Bias Point. LOWER: the range below the Bias Point UPPER: the range above the Bias Point LOWER&UPPER: the ranges both above and below the Bias Point ALL: the entire keyboard will be biased at the angle determined by the Bias Level, relative to the Bias Point

Time Keyfollow (TVA Envelope Time Key Follow)


Use this parameter when you want keyboard position to affect TVA envelope times (T2T4). Higher values will result in a greater change relative to middle C (C4). Positive (+) settings will result in shorter times as you play toward the right of the keyboard. Negative (-) settings will result in longer times as you play toward the right of the keyboard.

TVA ENVELOPE (TVA Envelope)


These parameters make settings for the TVA envelope (changes over time in the TVA level).
fig.3-46.e

PAN MODULATE
Use these parameters to affect the location of the TVA Pan.

T1

T2 L1 L2

T3

T4

Level

Keyfollow (Pan Key Follow)


Use this parameter when you want the keyboard position to change the stereo location. Higher values will result in greater change relative to middle C (C4). Positive (+) settings will cause notes played toward the right of the keyboard to be panned right. Negative (-) settings will cause the opposite.

L3

Time key is pressed key is released

Random (Random Pan Depth)


Use this parameter when you want the stereo location to change randomly each time you press a key. Higher values will result in a greater width of change.

T1T4 (TVA Envelope 14)


Adjust the time over which the volume changes from one point to the next.

L1L3 (TVA Envelope 13)


Adjust the volume level of each point relative to the basic TVA level.

Alternate (Alternate Pan Depth)


Use this parameter when you want the stereo location to alternate between left and right each time you press a key. Higher values will result in a greater width of change.

82

Chapter 3. Creating Your Own Sounds

Functions of Performance Parameters


fig.3-11

SINGLE: When you play the keyboard, only the specified Part (the Part shown in the display) will sound. MIDI messages will be transmitted from the controller section to the external MIDI devices even if the Local parameter and Tx parameter settings for each Part (PERFORM/MIDI/MIDI) are turned off. * If you have selected a Layer-type Performance, the upper right of the PERFORM PLAY display will indicate LAYER p* (* is the part number). If you have selected a Single-type Performance, the number of the Part that can be played from the keyboard will be displayed. * If LAYER has been selected and you try to play Patches of all Parts, you probably wont be able to play many simultaneous voices. When layering Patches, be aware of the number of voices available and turn off unnecessary Parts. Making Key Range settings for each Part allows you to split the keyboard to play different Parts in separate sections. PLAY display, hold down [SHIFT] while you press [SOLO].

s Settings Common to the Entire Performance (COMMON)


This display is used when setting parameters that are not part of other groups. These include Performance Name and Key Mode.

PERFORM NAME (Performance Name)


You can assign a name to the Performance of up to 12 characters. * For details on assigning names, refer to Assigning a Name (p. 46).

PERFORM CLOCK
Some parameters allow you to set a time value in terms of a note length which is determined by a specified tempo; Rate parameters (PATCH/LFO/LFO1, 2), Time parameter (PATCH/WAVE/TONE DELAY), and some Multi-Effects parameters. The specified tempo used by these parameters can be set for each Patch. However when a Patch is used in Performance mode, the Patch settings will be ignored, and the settings of this display will be used instead.

Key Range (Key Range Switch)


This parameter determines whether or not the Key Range settings (next display) will be applied or not. If you want them to be applied, turn this ON.

KEY RANG (Key Range)


Set the range in which each Part will sound. Use this when you wish to play different Patches in different areas of the keyboard.

Source (Performance Clock Source)


Select the source of the Performance Clock. PERFORM: Synchronize to the Performance Tempo setting. SYSTEM: Synchronize to the tempo clock of the ststem. * The Performance Clock does not transmit clock messages from MIDI OUT connector.

Lower (Key Range Lower)


Set the lowest note that the Part will play.

Upper (Key Range Upper)


Set the highest note that the Part will play. * If Key Range settings have been made for the Patch, only the notes for which the Key Range settings of the Patch and Performance overlap will play. * It is not possible to set Lower to a value greater than Upper, nor Upper to a value less than Lower. If you attempt to do so, both values will change together. * If you have used Octave Shift (System) or the Transpose parameter (SYSTEM/CONTROL/KEYBOARD) to transpose the pitch of the XP-30s keyboard, the keyboard area specified by Key Range will also be shifted.

Tempo (Performance Tempo)


Set the Performance Tempo setting. * When Source (Performance Clock Source) is set to SYSTEM, synchronization will be according to the tempo clock of the system, so it will not be possible to set the tempo value. The tempo of the system will be displayed in parentheses ( ).

PERFORM COMMON
Key Mode
This parameter determines how the sound source will be played from the XP-30s keyboard. LAYER: When you play the keyboard, all Parts whose Local parameter (PERFORM/MIDI/MIDI) is turned on will sound. Transmission of MIDI messages from the controller section to external MIDI devices will be determined by the Tx parameter setting (PERFORM/MIDI/MIDI) of each Part.

KEYBOARD
Octave Shift
This parameter adjusts the pitch of each Part in units of an octave (-3+3 octaves).

83

Chapter 3

* To switch between SINGLE and LAYER from the PERFORM

Chapter 3. Creating Your Own Sounds

s Setting Effects for a Performance (EFFECTS)


This group contains settings for the Multi-Effects/Chorus/ Reverb effects used by a Performance.

When the EFX Parameter Settings of a Patch Are Selected


When the EFX parameter settings of a Patch are selected, those settings will be displayed in the EFX parameter setting display of the Performance, and you will be able to modify them. If you wish to keep the Patch EFX parameter settings that you modify, rewrite the Patch settings. The modified Patch EFX parameter settings will be lost if you select a different Patch.

OUTPUT
Specify how each Part will be output.

Output Assign (Output Assign/Output Level)


Select whether the output of each Part will be sent through Multi-Effects, and adjust the volume level of each Part. MIX: output to the OUTPUT jack without passing through Multi-Effects. EFX: output to the OUTPUT jack through Multi-Effects. PATCH: use the Output Assign settings (for each Tone) of the Patch assigned to each Part. * If you select MIX or EFX, the setting of the Output Assign parameter (PATCH/EFFECTS/OUTPUT) will be ignored.

PERFORM EFX PRM (Performance EFX Parameters)


The EFX parameters for the selected EFX Type will be displayed. For details refer to Multi-Effects Types (EFX Parameter) (p. 93). * If EFX Source has been set to use the EFX parameter settings of the Patch assigned to one of the Parts, the Part number will be shown in the upper left of the display.

Chorus (Chorus Send Level)


Adjust the amount of Chorus that is applied to each Part.

Reverb (Reverb Send Level)


Adjust the amount of Reverb that is applied to each Part.

PERFORM EFX TYPE (Performance EFX TYPE)


These parameters set the Performance Multi-Effects. * If EFX Source has been set to use the EFX settings of the Patch assigned to one of the Parts, the Part number will be shown in the upper left of the display.
fig.3-47

PERFORM EFX OUT (Performance EFX Output)


These parameters specify the output for the Part for which EFX was selected in Output Assign. * For Parts which have an Output Assign setting of MIX, the settings of this display will be ignored. * For Parts which have an Output Assign setting of PATCH, the Output Assign settings of each Tone of the Patch will be used. In other words, the settings of this display will apply only to Tones for which EFX is selected.

Type (EFX Type)


Select the type of Multi-Effects. For details refer to MultiEffects Types (EFX Parameter) (p. 93). * If you have selected the EFX parameter settings of one of the Patches assigned to a Part as the EFX Source, the EFX Type of that Patch will be displayed.

Mix Out (EFX Output Level)


Adjust the volume of the direct sound and Multi-Effects sound.

Chorus (Chorus Send Level)


Adjust the amount of Chorus applied to the sound that passes through Multi-Effects.

Reverb (Reverb Send Level)


Adjust the amount of Reverb applied to the sound that passes through Multi-Effects.

Source (EFX Source)


Select the EFX parameter settings that will be used by the Performance. If you wish to use the EFX parameter settings of the Performance, select PERFORM. If you wish to use the EFX parameter settings of the Patch assigned to one of the Parts, select the Part number. Since the Rhythm Set does not have EFX parameter settings, it is not possible to select Part 10.

PERFORM EFX CTRL (Performance EFX Control)


Use this parameter when you wish to use a specific controller to control an EFX parameter. The types of EFX parameters available for control will depend on the EFX type. For details refer to Multi-Effects Types (EFX Parameter) (p. 93). The upper line of the display will show the EFX parameter to be controlled. For each EFX parameter you can specify the EFX Control Source and the EFX Control Depth.

84

Chapter 3. Creating Your Own Sounds

EFX Control Source 1, 2


The MIDI controllers that can be used are shown below. If you wish to use a controller that is common to all Patches, or a controller that cannot be selected here, first select SYSCTRL1 or SYS-CTRL2, and then use the Control 1/2 parameter (SYSTEM/CONTROL/SYS-CTRL ASSIGN) to select the controller. OFF: a controller will not be used SYS-CTRL1: System controller (Control 1) SYS-CTRL2: System controller (Control 2) MODULATION: Modulation (MIDI controller number 1) BREATH: Breath (MIDI controller number 2) FOOT: Foot (MIDI controller number 4) VOLUME: Volume (MIDI controller number 7) PAN: Pan (MIDI controller number 10) EXPRESSION: Expression (MIDI controller number 11) PITCH BEND: Pitch bend AFTERTOUCH: Aftertouch

Out (Chorus Output Assign)


Select the way in which the Chorus and Reverb are connected. MIX:
fig.3-27.e

The Chorus sound and the Reverb sound are mixed.

Chorus input

Reverb OUTPUT

Reverb input

Chorus

REV:Apply reverb to the chorus sound.


fig.3-28.e

Chorus input Chorus Reverb input Reverb OUTPUT

Adjust the amount of change that will occur in response to controller movement. Higher values will result in greater change. Negative (-) values will invert the direction of the change.

M+R: Mix the chorus sound to which reverb is not applied and the chorus sound to which reverb is applied.
fig.3-29.e

PERFORM CHORUS
Make settings for the Chorus effect of the Performance. * In Performance mode, the Chorus settings of the Patches used by each Part will be ignored (except for the Send Level parameter).

Reverb input

Chorus

Reverb

OUTPUT

Chorus input

PERFORM REVERB
Make settings for the Reverb effect of the Performance. * In Performance mode, the Reverb settings of the Patches used by each Part will be ignored (except for the Send Level parameter).

Rate (Chorus Rate)


Adjust the speed of modulation for the chorus.

Depth (Chorus Depth)


Adjust the depth of modulation for the chorus.

Type (Reverb/Delay Type)


Select the type of Reverb effect. ROOM1: dense reverb with short decay ROOM2: sparse reverb with short decay STAGE1: reverb with greater late reverberation STAGE2: reverb with strong early reflections HALL1: reverb with clear reverberance HALL2: reverb with rich reverberance DELAY: a conventional delay PAN-DLY: a delay with echoes that move left and right

Delay (Chorus Pre Delay)


Adjust the time delay from when the direct sound begins until the chorus sound is heard. Higher values will create a more spacious sound.

Fbk (Chorus Feedback Level)


Adjust the amount of chorus sound that is returned (fed back) into the chorus. Higher values will create a more intense effect.

Level (Chorus Level)


Adjust the volume level of the chorus sound.

Time (Reverb/Delay Time)


Adjust the time of reverberation. If you have selected DELAY or PAN-DLY, this parameter will adjust the time delay from the original sound until the first echo will sound.

85

Chapter 3

EFX Control Depth 1, 2

Chapter 3. Creating Your Own Sounds

Fbk (Delay Feedback Level)


Adjust the amount of delayed sound that is returned (fed back) to the delay. Higher values result in more delay repeats. * If you have selected any one of the Reverb types (ROOM1 HALL2), this parameter has no effect.

Local (Local Switch)


Specify for each Part whether or not you want to disconnect the controller section from the internal sound source when the Key Mode parameter (PERFORM/COMMON/ PERFORM COMMON) is set to LAYER.. Normally you will leave this ON, but you can turn it OFF when you want to use the XP-30 only to control an external sound source. * To switch between ON and OFF from the PERFORM PLAY display, press the function button for the Part you want to alter. * When the Key Mode parameter (PERFORM/COMMON/ PERFORM COMMON) is at SINGLE, the setting for the Local parameter is deactivated, and when you finger the keyboard, only the patch for the current Part sounds.

HF Damp (Reverb/Delay HF Damp)


Adjust the frequency above which the reverberant sound will be cut. As the frequency is set lower, more of the high frequencies will be cut, resulting in a softer and more muted reverberance. If you do not want the high frequencies to be cut, set this parameter to BYPASS.

Level (Reverb/Delay Level)


Adjust the volume of the reverberant (or delayed) sound.

s Making MIDI Settings for a Part (MIDI)


MIDI
These parameters determine how each Part will transmit and receive MIDI messages.

RxSWITCH (Receive Switch)


Specify whether each Part will receive certain MIDI messages or not.

Volume (Receive Volume Switch)


If you want the Part to receive Volume messages, turn this ON. If not, turn this OFF.

Channel (MIDI Channel)


Set the MIDI channel of each Part. * If this is set to the same channel as the Control Channel parameter (SYSTEM/MIDI/PERFORM MIDI), attempting to use MIDI messages (Program Change and Bank Select) from an external device to select Patches will select Performances instead. If you want to select Patches, change the Control Channel to a different setting.

Hold-1 (Receive Hold 1 Switch)


If you want the Part to receive Hold 1 messages, turn this ON. If not, turn this OFF.

Program Change (Receive Program Change Switch)


If you want the Part to receive Program Change messages, turn this ON. If not, turn this OFF. * If you want a Part to receive Program Change messages, you must also turn the Program Change parameter ON (SYSTEM/ MIDI/RECEIVE MIDI).

Rx (Receive Switch)
Specify whether or not you want each Part to receive MIDI messages from the external MIDI devices. Normally you will leave this ON, but you can turn it OFF when you do not want a specific Part to be playing during a song playback. * To switch between ON and OFF from the PERFORM PLAY display, hold down [SHIFT] while you press the function button for the Part you want to alter.

TRANSMIT (Transmit Bank Select)


BankSelectGroup (Transmit Bank Select Group)
When you select a Performance, Bank Select and Program Change messages will be transmitted for the Patch or Rhythm Set assigned to each Part as determined by this setting. PATCH: When you select a Performance, Bank Select messages and Program Change messages for the Patch/Rhythm Set that is assigned to each Part will not be transmitted. BS1-7: When you select a Performance, Bank Select and Program Change messages will be transmitted for the Patch/Rhythm Set that is assigned to each Part. In this case, the Bank Select Number that is transmitted will be determined by the Bank Select Group (BS17) setting. In the BANK SEL GROUP display (SYSTEM/MIDI) you can set the Bank Select number for each Bank Select Group.

Tx (Transmit Switch)
This determines, for each Part, whether or not data generated by the controller section is sent as MIDI messages from the MIDI OUT connector when the Key Mode parameter (PERFORM/COMMON/PERFORM COMMON) is set to LAYER. Normally you will leave this ON, but you can turn it OFF when you do not want the XP-30 to control external sound sources. * When the Key Mode parameter (PERFORM/COMMON/ PERFORM COMMON) is set to SINGLE, the setting for the Tx parameter is deactivated, and only the MIDI messages of the current Part are sent from the MIDI OUT connector.

86

Chapter 3. Creating Your Own Sounds

* Bank Select and Program Change messages will not be transmitted for Parts whose Tx parameter (PERFORM/MIDI/ MIDI) is turned off.

s Confirming MIDI Information for Each Part (INFO)


INFO (Part Information)
The displays in this group allow you to check various settings such as MIDI message reception status for each Part. This is convenient when you need to check that the sound source is responding correctly to messages from the keyboard or external MIDI controller.

Transmit Volume
If you want Volume messages to also be transmitted when you select a Performance, specify the desired volume here. If you do not want Volume messages to be transmitted, set this to OFF.

s Making Settings for Each Part (PART)


PATCH
Select the Patch for each Part.

Mod (Modulation Information) Breath (Breath Information) Foot (Foot Information) Vol (Volume Information) Pan (Pan Information) Exp (Expression Information) Hold (Hold 1 Information) Aft (Aftertouch Information) Sys1 (System Controller 1 Information)
The MIDI message specified as the Control 1 parameter (SYSTEM/CONTROL/SYS-CTRL ASSIGN)

Group (Patch Group)


Select the group of the Patch (or Rhythm Set for Part 10). USER: User memory PR-AC, E: Preset memory AC, E GM: Preset memory GM XP-AE: Wave Expansion Board AE * It is not possible to select a group for a Wave Expansion Board that has not been installed.

Number (Patch Number)


Specify the number of the Patch. The Patch name will be displayed in parentheses ( ).

Sys2 (System Controller 2 Information)


The MIDI message specified as the Control 2 parameter (SYSTEM/CONTROL/SYS-CTRL ASSIGN)

SETTING
Make volume, pan, and pitch settings for each Part.

Voices (Voice Information)


The number of voices used

Level
Adjust the volume of each Part. Use this parameter to adjust the volume balance between Parts.

Pan
Adjust the stereo location of the Part. L64 is full left, 0 is center, and 63R is full right.

MIDI Message Transmission


When you modify a value (other than Voice) in the INFO display, the MIDI message of the modified value will be transmitted to the internal sound source and to external MIDI devices. The way in which the message will be transmitted will depend on the settings of the currently selected Performance. If you have selected a Single-type Performance, the MIDI message will be transmitted to the specified Part, and will simultaneously be transmitted to external MIDI devices on the MIDI channel of that Part. If you have selected a Layer-type Performance, the MIDI message will be transmitted to all Parts whose Tx parameter (PERFORM/MIDI/MIDI) is turned on, and will also be transmitted to external MIDI devices on the MIDI channel of each of these Parts.

Coarse (Coarse Tune)


Adjust the pitch of the Part in semitone steps (-4+4 octaves).

Fine (Fine Tune)


Adjust the pitch of the Part in 1-cent steps (-50+50 cents). * One cent is 1/100th of a semitone.

RESERVE (Voice Reserve)


Voice Reserve
This setting determine how many voices will be reserved for each Part when more than 64 simultaneous voices are requested. * It is not possible to make Voice Reserve settings that would cause the total of all Parts to be greater than 64 voices. The number of remaining voices available is indicated at the right of the parameter name (rest=). Keep this in mind as you make settings.

87

Chapter 3

Bend (Bender Information)

Chapter 3. Creating Your Own Sounds

Functions of Rhythm Set Parameters


fig.3-16

Type (EFX Type)


Select the type of EFX. For details refer to Multi-Effects Types (EFX Parameter) (p. 93). * If you have selected the EFX parameter settings of one of the Patches assigned to a Part as the EFX Source, the EFX Type of that Patch will be displayed.

s Naming a Rhythm Set (COMMON)


RHYTHM NAME (Rhythm Set Name)
You can assign a name of up to 12 characters to a Rhythm Set. * For details on assigning names, refer to Assigning a Name (p. 46).

Source (EFX Source)


Select the EFX parameter settings that will be used by the Performance. If you wish to use the EFX parameter settings of the Performance, select PERFORM. If you wish to use the EFX parameter settings of the Patch assigned to one of the Parts, select the Part number.

When the EFX Parameter Settings of a Patch Are Selected


When the EFX parameter settings of a Patch are selected, those settings will be displayed in the EFX parameter setting display of the Performance, and you will be able to modify them. If you wish to keep the Patch EFX parameter settings that you modify, rewrite the Patch settings. The modified Patch EFX parameter settings will be lost if you select a different Patch.

s Setting Effects for a Rhythm Tone (EFFECTS)


* Rhythm Sets use the effect settings of the Performance currently selected in Performance mode. You can modify the Performance effect settings from inside Rhythm Set mode, but they are not stored as Rhythm Set settings. If you wish to keep the effect settings, you need to store them as Performance settings.

OUTPUT
Specify the output for each key.

PERFORM EFX PRM (Performance EFX Parameters)


The EFX parameters for the selected EFX Type will be displayed. For details refer to Multi-Effects Types (EFX Parameter) (p. 93). * If EFX Source has been set to use the EFX parameter settings of the Patch assigned to one of the Parts, the Part number will be shown in the upper left of the display.

Output Assign (Output Assign/Output Level)


For the output of each key, specify whether or not it will be sent through Multi-Effects, and adjust the volume level. MIX: output to the OUTPUT jack without passing through Multi-Effects. EFX: output to the OUTPUT jack after passing through Multi-Effects.

Chorus (Chorus Send Level)


Adjust the amount of Chorus for each key.

PERFORM EFX OUT (Performance EFX Output)


These parameters specify the output for the keys for which EFX was selected in Output Assign. * For keys which have an Output Assign setting of MIX, the settings of this display will be ignored.

Reverb (Reverb Send Level)


Adjust the amount of Reverb for each key.

PERFORM EFX TYPE (Performance EFX Type)


* If EFX Source has been set to use the EFX parameter settings of the Patch assigned to one of the Parts, the Part number will be shown in the upper left of the display.

Mix Out (EFX Output Level)


Adjust the volume of the direct sound and Multi-Effects sound.

Chorus (Chorus Send Level)


Adjust the amount of Chorus applied to the sound that passes through Multi-Effects.

Reverb (Reverb Send Level)


Adjust the amount of Reverb applied to the sound that passes through Multi-Effects.

88

Chapter 3. Creating Your Own Sounds

PERFORM EFX CTRL (Performance EFX control)


Use this parameter when you wish to use a specific controller to control an EFX parameter. The types of EFX parameters available for control will depend on the EFX type. For details refer to Multi-Effects Types (EFX Parameter) (p. 93). The upper line of the display will show the EFX parameter to be controlled. For each EFX parameter you can specify the EFX Control Source and the EFX Control Depth.

Level (Chorus Level)


Adjust the volume level of the chorus sound.

Out (Chorus Output Assign)


Select the way in which the Chorus and Reverb are connected. MIX:
fig.3-27.e

The Chorus sound and the Reverb sound are mixed.

Chorus input

Reverb OUTPUT

EFX Control Source 1, 2


The MIDI controllers that can be used are shown below. If you wish to use a controller that is common to all Patches, or a controller that cannot be selected here, first select SYSCTRL1 or SYS-CTRL2, and then use the Control 1/2 parameter (SYSTEM/CONTROL/SYS-CTRL ASSIGN) to select the controller. OFF: a controller will not be used SYS-CTRL1: System controller (Control 1) SYS-CTRL2: System controller (Control 2) MODULATION: Modulation (MIDI controller number 1) BREATH: Breath (MIDI controller number 2) FOOT: Foot (MIDI controller number 4) VOLUME: Volume (MIDI controller number 7) PAN: Pan (MIDI controller number 10) EXPRESSION: Expression (MIDI controller number 11) PITCH BEND: Pitch bend AFTERTOUCH: Aftertouch
Reverb input Chorus

REV:Apply reverb to the chorus sound.


fig.3-28.e

Chorus input Chorus Reverb input Reverb OUTPUT

M+R: Mix the chorus sound to which reverb is not applied and the chorus sound to which reverb is applied.
fig.3-29.e

Reverb input

Chorus

Reverb

OUTPUT

EFX Control Depth 1, 2


Adjust the amount of change that will occur in response to controller movement. Higher values will result in greater change. Negative (-) values will invert the direction of the change.
Chorus input

PERFORM REVERB
Make settings for the Reverb effect of the Performance.

PERFORM CHORUS
Make settings for the Chorus effect of the Performance.

Type (Reverb/Delay Type)


Select the type of Reverb effect. ROOM1: dense reverb with short decay ROOM2: sparse reverb with short decay STAGE1: reverb with greater late reverberation STAGE2: reverb with strong early reflections HALL1: reverb with clear reverberance HALL2: reverb with rich reverberance DELAY: a conventional delay PAN-DLY: a delay with echoes that move left and right

Rate (Chorus Rate)


Adjust the speed of modulation for the chorus.

Depth (Chorus Depth)


Adjust the depth of modulation for the chorus.

Delay (Chorus Pre Delay)


Adjust the time delay from when the direct sound begins until the chorus sound is heard. Higher values will create a more spacious sound.

Time (Reverb/Delay Time)


Adjust the time of the reverberation. If you have selected DELAY or PAN-DLY, this parameter will adjust the time delay from the original sound until the first echo will sound.

Fbk (Chorus Feedback Level)


Adjust the amount of chorus sound that is returned (fed back) into the chorus. Higher values will create a more intense effect.

89

Chapter 3

Chapter 3. Creating Your Own Sounds

Fbk (Delay Feedback Level)


Adjust the amount of delayed sound that is returned (fed back) to the delay. Higher values result in more delay repeats. * If you have selected any one of the Reverb types (ROOM1 HALL2), this parameter has no effect.

Volume (Receive Volume Switch)


If you want Volume messages to be received, turn this parameter ON. If not, turn it OFF. * In order for Volume messages to be received, the Volume parameter (PERFORM/MIDI/RxSWITCH) must also be turned ON for Part 10 of the currently selected Performance.

HF Damp (Reverb/Delay HF Damp)


Adjust the frequency above which the reverberant sound will be cut. As the frequency is set lower, more of the high frequencies will be cut, resulting in a softer and more muted reverberance. If you do not want the high frequencies to be cut, set this parameter to BYPASS.

Pan (Receive Pan Control Switch)


Specify how Pan messages will be received. OFF: Not received. CONT: Whenever a Pan message is received, it will immediately change the stereo location of the sound. KEY-ON: The stereo location of the sound will be changed when the next note is played. If a Pan message is received while a note is sounding, the current stereo location will not change until the next note. In this case, the stereo location will change only for the note played later, and the currently sounding note will not move.

Level (Reverb/Delay Level)


Adjust the volume of the reverberant (or delayed) sound.

s Controlling How a Rhythm Tone will Sound with Controllers (CONTROL)


The parameters in this group determine how the controllers function and how instruments in a Rhythm Set will sound.

Hold-1 (Receive Hold 1 Switch)


If you want Hold 1 messages to be received, turn this parameter ON. If not, turn it OFF. * In order for Hold 1 messages to be received, the Hold-1 parameter (PERFORM/MIDI/RxSWITCH) must also be turned ON for Part 10 of the currently selected Performance.

CONTROL
These parameters determine how each note is controlled.

Bend Range
Specify the amount of pitch change (in semitones) that will occur when the Pitch Bend Lever is moved (maximum +1 octave).

Env Mode (Envelope Mode)


When a loop-type Wave is selected, it will normally continue to sound as long as the key is pressed. If you want it to decay naturally even if the key remains pressed, set this to NO-SUS. * If a one-shot type Wave is selected, it will not sustain even if this parameter is set to SUSTAIN.

s Modifying Waveform of a Rhythm Tone (WAVE)


Make settings for the basic waveform (Wave) of the Rhythm Tone assigned to each key.

WAVE
Group (Wave Group)
Select the Group of the Wave. INT-A, B: Internal A, B EXP-AE: Wave Expansion Boards AE * It is not possible to select a Group of a Wave Expansion Board that is not installed.

Mute Group
The Mute Group function lets you specify that certain Rhythm Tones not be allowed to sound simultaneously. Taking the example of an acoustic drum set, it is obviously impossible for an open hi-hat and a closed hi-hat sound to occur simultaneously. To simulate this type of situation on the XP30, set each hi-hat sound to the same Mute Group number. Up to 31 Mute Groups can be used. If you do not want a Rhythm Tone to use a Mute Group, turn it OFF.

Number (Wave Number)


Select the Wave number. The name of the Wave will be displayed in parentheses ( ).

RxSWITCH (Receive Switch)


These parameters determine how each key will receive Volume / Pan / Hold 1 MIDI messages.

Gain (Wave Gain)


Adjust the gain (volume boost) of the Wave. The setting range is -6+12 dB, in steps of 6 dB. An increase of 6 dB doubles the gain.

Switch (Key Switch)


Turn this ON for keys you wish to sound, and OFF for keys you do not wish to sound.

90

Chapter 3. Creating Your Own Sounds

s Modifying Pitch of a Rhythm Tone (PITCH)


This group contains parameters that affect the pitch of the Rhythm Tone for each key.

T14 (Pitch Envelope Time 14)


Specify the time over which the pitch will change from one point to the next.

L14 (Pitch Envelope Level 14)


Specify the pitch change for each point relative to the basic pitch.

PITCH
Specify the basic pitch for the Rhythm Tone.

Coarse (Coarse Tune)


Select the key corresponding to the pitch at which you wish to sound the Rhythm Tone.

s Changing the Tone (Filter) of a Rhythm Tone (TVF)


The TVF (Time Variant Filter) uses a filter to modify the frequency characteristics of the sound.

Fine (Fine Tune)


Adjust the pitch in 1-cent steps (-50+50 cents). * One cent is 1/100th of a semitone.

FILTER
Make TVF filter settings.

Random (Random Pitch Depth)


If you want the pitch to change randomly each time you press a key, specify the width of the change. If you do not want random pitch change, set this parameter to 0. The value is in units of 1 cent.

Type (Filter Type)


Select the filter type. OFF: filter not used. LPF (Low Pass Filter): Cut the frequencies above the Cutoff Frequency. This is the most common type of filter used in synthesizers. BPF (Band Pass Filter): Pass only the frequencies in the area of the Cutoff Frequency. HPF (High Pass Filter): Cut the frequencies below the Cutoff Frequency. PKG (Peaking Filter): Emphasize the frequencies in the area of the Cutoff Frequency.

Env Depth (Pitch Envelope Depth)


Adjust the effect of the Pitch Envelope. Higher settings will result in greater change. Negative (-) settings will invert the envelope.

PCH VELOCITY
Specify how key velocity will change the effect of the Pitch Envelope.

Velocity Sens (Pitch Envelope Velocity Sensitivity)


Use this parameter if you want key velocity to change the effect of the Pitch Envelope. Higher settings will result in a greater difference between strongly and softly played notes. Negative (-) settings will invert the change.

Cutoff (Cutoff Frequency)


Set the basic frequency of the filter.

Resonance
Emphasize the frequencies in the area of the Cutoff Frequency. For some settings, excessive levels can cause oscillation and distortion.
fig.3-43.e

Velocity Time (Pitch Envelope Time Velocity Sensitivity)


Use this parameter if you want key velocity to change the overall time of the Pitch Envelope. Higher settings will result in a greater time difference between strongly and softly played notes. Negative (-) settings will invert the change.

LPF Level High


Frequency

BPF

HPF

PKG

PCH ENVELOPE
Make settings for the Pitch Envelope (changes in pitch over time).
fig.3-42.e

T1 L1

T2

T3

T4

L3

Pitch Time key is pressed


L2

Env Depth (TVF Envelope Depth)


Adjust the depth of the TVF envelope. Higher settings will result in greater change. Negative (-) values will invert the envelope.

key is released L4

parameter value

Cutoff frequency

Low

91

Chapter 3

Chapter 3. Creating Your Own Sounds

TVF VELOCITY
V-Sens (TVF Envelope Velocity Sensitivity)
Use this parameter when you want velocity to affect the TVF Envelope. Higher settings will result in a greater difference between strongly and softly played notes. Negative (-) settings will invert the effect.

Pan
Adjust the pan (stereo location) of the Rhythm Tone. L64 is full left, 0 is center, and 63R is full right.

Random (Random Pan Depth)


Use this parameter when you want the stereo location to change randomly each time you press a key. If you do not want the stereo location to change randomly, set this to 0.

V-Time (TVF Envelope Time Velocity Sensitivity)


Use this parameter when you want velocity to affect the time of the TVF envelope. Higher settings will result in a greater time difference between strongly and softly played notes. Negative (-) settings will invert the effect.

Alternate (Alternate Pan Depth)


Use this parameter when you want the stereo location to alternate between left and right each time you press a key. Higher values will result in a greater width of change. L or R values can be set, and this will reverse the left/right order of the panning. If you want to alternate the pan position of two Rhythm Tones, set them to opposite L and R settings.

V-Resonance (Resonance Velocity Sensitivity)


Use this parameter when you want velocity to affect the Resonance. Higher settings will result in a greater difference between strongly and softly played notes. Negative (-) settings will invert the effect.

TVA VELOCITY
Specify how keyboard velocity will affect the time of the TVA envelope.

TVF ENVELOPE
These parameters set the TVF envelope (the way in which the cutoff frequency will change over time).
fig.3-44.e

Velocity Sens (TVA Envelope Velocity Sensitivity)


Use this parameter when you want velocity to affect the TVA Envelope. Higher settings will result in a greater difference between strongly and softly played notes. Negative (-) settings will invert the effect.

T1 L1

T2

T3

T4

L2

L3 L4

Cutoff Frequency key is pressed

Velocity Time (TVA Envelope Time Velocity Sensitivity)


Use this parameter when you want velocity to affect the time of the TVA envelope. Higher settings will result in a greater time difference between strongly and softly played notes. Negative (-) settings will invert the effect.

Time key is released

T1T4 (TVF Envelope Time 14)


Set the times over which the cutoff frequency will move from one point to the next.

TVA ENVELOPE
These parameters make settings for the TVA envelope (changes over time in the TVA level).
fig.3-46.e

L1L4 (TVF Envelope Level 14)


Set the cutoff frequency levels for each point, relative to the basic cutoff frequency.

T1

T2 L1 L2

T3

T4

Level

s Changing the Volume and Stereo Location of a Rhythm Tone (TVA)


The TVA (Time Variant Amplifier) controls volume changes and stereo location.
key is pressed

L3

Time key is released

TVA
Level
Adjust the basic volume of the Rhythm Tone. Use this parameter to adjust the volume balance between Rhythm Tones.

T1T4 (TVA Envelope Time 14)


Adjust the time over which the volume changes from one point to the next.

L1L3 (TVA Envelope Level 13)


Adjust the volume level of each point relative to the basic TVA level.

92

Chapter 3. Creating Your Own Sounds

Multi-Effects Types (EFX Parameter)


Multi-Effects provides 40 types of effect. Some of these consist of two different effects connected in series or parallel. * Parameters marked with a sharp # can be controlled using a specified controller (Two setting items will change simultaneously for #1 and #2). Settings in the Patch or Performance EFX Control display (PATCH/EFFECTS/PATCH EFX CTRL or PERFORM/EFFECTS/PERFORM EFX CTRL) will determine how these parameters are controlled.

P2 Gain (Peaking 2 Gain)


Adjust the gain for the area specified by the Peaking 2 Frequency and Q settings.

Level (Output Level) #


Adjust the output level.

2: OVERDRIVE
This effect creates a soft distortion similar to that produced by vacuum tube amplifiers.
fig.3-49

L in Over drive R in Amp Simulator 2-Band EQ

L out
Pan L Pan R

1: STEREO-EQ (Stereo Equalizer)


This is a four-band stereo equalizer (low, mid x 2, high).
fig.3-48

R out

Drive #
Adjust the degree of distortion. The volume will change together with the degree of distortion.

L in

4-Band EQ

L out

R in

4-Band EQ

R out

Level (Output Level) LowGain (Low Gain)


Adjust the gain of the low frequency range.

LowFreq (Low Frequency)


Select the frequency of the low range (200 Hz/400 Hz).

LowGain (Low Gain)


Adjust the gain of the low frequency.

Hi Gain (High Gain)


Adjust the gain of the high frequency range.

Hi Freq (High Frequency)


Select the frequency of the high range (4000 Hz/8000 Hz).

Amp Type (Amp Simulator Type)


Select the type of guitar amp. SMALL: small amp BUILT-IN: single-unit type amp 2-STACK: large double stack amp 3-STACK: large triple stack amp

Hi Gain (High Gain)


Adjust the gain of the high frequency.

P1 Freq (Peaking 1 Frequency)


Adjust the frequency of Peaking 1 (mid range).

P1 Q (Peaking 1 Q)
This parameter adjusts the width of the area around the Peaking 1 Frequency that will be affected by the Gain setting. Higher values of Q will result in a narrower area being affected.

Pan (Output Pan) #


Adjust the stereo location of the output sound. L64 is far left, 0 is center, and 63R is far right.

3: DISTORTION
This effect produces a more intense distortion than Overdrive.
fig.3-50

P1 Gain (Peaking 1 Gain)


Adjust the gain for the area specified by the Peaking 1 Frequency and Q settings.

L in Distortion R in Amp Simulator 2-Band EQ

L out
Pan L Pan R

P2 Freq (Peaking 2 Frequency)


Adjust the frequency of Peaking 2 (mid range).

R out

P2 Q (Peaking 2 Q)
This parameter adjusts the width of the area around the Peaking 2 Frequency that will be affected by the Gain setting. Higher values of Q will result in a narrower area being affected.

Drive #
Adjust the degree of distortion. The volume will change together with the degree of distortion.

Level (Output Level)


Adjust the output level.

LowGain (Low Gain)


Adjust the gain of the low frequency range.

93

Chapter 3

Adjust the output level.

Chapter 3. Creating Your Own Sounds

Hi Gain (High Gain)


Adjust the gain of the high frequency range.

5: SPECTRUM
Spectrum is a type of filter which modifies the timbre by boosting or cutting the level at specific frequencies. It is similar to an equalizer, but has 8 frequency points fixed at locations most suitable for adding character to the sound.
fig.3-52

Amp Type (Amp Simulator Type)


Select the type of guitar amp. SMALL: small amp BUILT-IN: single-unit type amp 2-STACK: large double stack amp 3-STACK: large triple stack amp

L in Spectrum

L out
Pan L Pan R

Pan (Output Pan) #


Adjust the stereo location of the output sound. L64 is far left, 0 is center, and 63R is far right.

R in

R out

Band 1 (Band 1 Gain)


Adjust the 250 Hz level.

4: PHASER
A phaser adds a phase-shifted sound to the original sound, producing a twisting modulation that creates spaciousness and depth.
fig.3-51

Band 2 (Band 2 Gain)


Adjust the 500 Hz level.

Band 3 (Band 3 Gain)


Adjust the 1000 Hz level.

L in Phaser
Mix

L out
Pan L Pan R

Band 4 (Band 4 Gain)


Adjust the 1250 Hz level.

R in

Resonance

R out

Band 5 (Band 5 Gain)


Adjust the 2000 Hz level.

Manual #
Adjust the basic frequency from which the sound will be modulated.

Band 6 (Band 6 Gain)


Adjust the 3150 Hz level.

Rate #
Adjust the frequency (period) of modulation.

Band 7 (Band 7 Gain)


Adjust the 4000 Hz level.

Depth
Adjust the depth of modulation.

Band 8 (Band 8 Gain)


Adjust the 8000 Hz level.

Res (Resonance)
Adjust the amount of feedback for the phaser.

Q
Simultaneously adjust the width of the adjusted areas for all the frequency bands.

Mix (Mix Level)


Adjust the ratio with which the phase-shifted sound is combined with the direct sound.

Pan (Output Pan) #


Adjust the stereo location of the output sound. L64 is far left, 0 is center, and 63R is far right.

Pan (Output Pan)


Adjust the stereo location of the output sound. L64 is far left, 0 is center, and 63R is far right.

Level (Output Level) #


Adjust the output level.

Level (Output Level)


Adjust the output level.

6: ENHANCER
The Enhancer controls the overtone structure of the high frequencies, adding sparkle and tightness to the sound.
fig.3-53

L in

Enhancer
Mix

2-Band EQ 2-Band EQ

L out

R in

Enhancer
Mix

R out

Sens (Sensitivity) #
Adjust the sensitivity of the enhancer.

94

Chapter 3. Creating Your Own Sounds

Mix (Mix Level) #


Adjust the ratio with which the overtones generated by the enhancer are combined with the direct sound.

8: ROTARY
The Rotary effect simulates the sound of the rotary speakers often used with the electric organs of the past. Since the movement of the high range and low range rotors can be set independently, the unique type of modulation characteristic of these speakers can be simulated quite closely. This effect is most suitable for electric organ Patches.
fig.3-55

LowGain (Low Gain)


Adjust the gain of the low frequency range.

Hi Gain (High Gain)


Adjust the gain of the high frequency range.

Level (Output Level)


Adjust the output level.

L in Rotary R in

L out

7: AUTO-WAH
The Auto Wah cyclically controls a filter to create cyclic change in timbre.
fig.3-54

R out

LowSlow (Low Frequency Slow Rate)


Adjust the slow speed (SLOW) of the low frequency rotor.

L in Auto Wah R in

L out

LowFast (Low Frequency Fast Rate)


Adjust the fast speed (FAST) of the low frequency rotor.

LowAccl (Low Frequency Acceleration)


R out

Select the type of filter. LPF: The wah effect will be applied over a wide frequency range. BPF: The wah effect will be applied over a narrow frequency range.

Low Lvl (Low Frequency Level)


Adjust the volume of the low frequency rotor.

Hi Slow (High Frequency Slow Rate)


Adjust the slow speed (SLOW) of the high frequency rotor.

Sens
Adjust the sensitivity with which the filter is controlled.

Hi Fast (High Frequency Fast Rate)


Adjust the fast speed (FAST) of the high frequency rotor.

Manual #
Adjust the center frequency from which the effect is applied.

Hi Accl (High Frequency Acceleration)


Adjust the time it takes the high frequency rotor to reach the newly selected speed when switching from fast to slow (or slow to fast) speed. Lower values will require longer times.

Peak
Adjust the amount of the wah effect that will occur in the area of the center frequency. Lower settings will cause the effect to be applied in a broad area around the center frequency. Higher settings will cause the effect to be applied in a more narrow range.

Hi Lvl (High Frequency Level)


Adjust the volume of the high frequency rotor.

Separation
Adjust the spatial dispersion of the sound.

Rate #
Adjust the frequency of the modulation.

Speed #
Simultaneously switch the rotational speed of the low frequency rotor and high frequency rotor. SLOW: Slow down the rotation to the specified speed (the Low Slow / Hi Slow values). FAST: Speed up the rotation to the specified speed (the Low Fast / Hi Fast values).

Depth
Adjust the depth of the modulation.

Level (Output Level)


Adjust the output level.

Level (Output Level) #


Adjust the output level.

95

Chapter 3

Filter (Filter Type)

Adjust the time it takes the low frequency rotor to reach the newly selected speed when switching from fast to slow (or slow to fast) speed. Lower values will require longer times.

Chapter 3. Creating Your Own Sounds

9: COMPRESSOR
The Compressor flattens out high levels and boosts low levels, smoothing out unevenness in volume.
fig.3-56

Pan (Output Pan) #


Adjust the stereo location of the output sound. L64 is far left, 0 is center, and 63R is far right.

L in Compressor R in 2-Band EQ

L out
Pan L Pan R

Level (Output Level) #


Adjust the output level.

R out

11: HEXA-CHORUS
Hexa-chorus uses a six-phase chorus (six layers of chorused sound) to give richness and spatial spread to the sound.
fig.3-58

Attack
Adjust the attack time of an input sound.

Sustain
Adjust the time over which low level sounds are boosted until they reach the specified volume.

L in
Balance D

L out
Balance W

Hexa Chorus
Balance W

Post Gain
Adjust the output gain.

R in
Balance D

R out

LowGain
Adjust the low frequency gain.

Pre Dly (Pre Delay Time)


Adjust the time delay from when the direct sound begins until the chorus sound is heard.

Hi Gain
Adjust the high frequency gain.

Rate #
Adjust the rate of modulation.

Pan (Output Pan) #


Adjust the stereo location of the output sound. L64 is far left, 0 is center, and 63R is far right.

Depth
Adjust the depth of modulation.

Level (Output Level) #


Adjust the output level.

Dly Dev (Pre Delay Deviation)


Pre Delay determines the time from when the direct sound begins until the processed sound is heard. Pre Delay Deviation adjusts the differences in Pre Delay between each chorus sound.

10: LIMITER
The Limiter compresses signals that exceed a specified volume level, preventing distortion from occurring.
fig.3-57

Dpt Dev (Depth Deviation)


Adjust the difference in modulation depth between each chorus sound.

L in Limiter R in 2-Band EQ

L out
Pan L Pan R

Pan Dev (Pan Deviation)


Adjust the difference in stereo location between each chorus sound. With a setting of 0, all chorus sounds will be in the center. With a setting of 20, each chorus sound will be spaced at 60 degree intervals relative to the center.

R out

Thresh (Threshold Level)


Adjust the volume at which compression will begin.

Ratio (Compression Ratio)


Adjust the compression ratio.

Balance (Effect Balance) #


Adjust the volume balance between the direct sound and the chorus sound. With a setting of D100:0W only the direct sound will be output, and with a setting of D0:100W only the chorus sound will be output.

Release (Release Time)


Adjust the time from when the volume falls below the Threshold Level until compression is no longer applied.

Gain (Post Gain)


Adjust the output gain.

Level (Output Level)


Adjust the output level.

LowGain
Adjust the low frequency gain.

Hi Gain
Adjust the high frequency gain.

96

Chapter 3. Creating Your Own Sounds

12: TREMOLO-CHORUS
Tremolo Chorus is a chorus effect with added Tremolo (cyclic modulation of volume).
fig.3-59

Phase
Adjust the spatial spread of the sound.

LowGain
Adjust the gain of the low frequency range.

L in
Balance D

L out
Balance W

Hi Gain
Adjust the gain of the high frequency range.

Tremolo Chorus
Balance W

Balance (Effect Balance) #


Adjust the volume balance between the direct sound and the chorus sound. With a setting of D100:0W only the direct sound will be output, and with a setting of D0:100W only the chorus sound will be output.

R in
Balance D

R out

Pre Dly (Pre Delay Time)


Adjust the time delay from when the direct sound begins until the chorus sound is heard.

Level (Output Level)


Adjust the output level.

ChoRate (Chorus Rate)


Adjust the modulation speed of the chorus effect.

ho Dpt (Chorus Depth)


Adjust the modulation depth of the chorus effect.

14: STEREO-CHORUS
This is a stereo chorus. A filter is provided so that you can adjust the timbre of the chorus sound.
fig.3-61

Phase (Tremolo Phase)


Adjust the spread of the tremolo effect.

Balance D

L in Chorus Chorus R in
Balance D

L out

TrmRate (Tremolo Rate) #


Adjust the modulation speed of the tremolo effect.

Balance W Balance W

Trm Sep (Tremolo Separation)


Adjust the spread of the tremolo effect.

2-Band EQ

R out

Balance (Effect Balance) #


Adjust the volume balance between the direct sound and the tremolo chorus sound. With a setting of D100:0W only the direct sound will be output, and with a setting of D0:100W only the tremolo chorus sound will be output.

Pre Dly (Pre Delay Time)


Adjust the time delay from when the direct sound begins until the processed sound is heard.

Rate #
Adjust the rate of modulation.

Level (Output Level)


Adjust the output level.

Depth
Adjust the depth of modulation.

13: SPACE-D
Space-D is a multiple chorus that applies two-phase modulation in stereo. It gives no impression of modulation, but produces a transparent chorus effect.
fig.3-60

Phase
Adjust the spatial spread of the sound.

Filter (Filter Type)


Select the type of filter. OFF: a filter will not be used LPF: cut the frequency range above the cutoff frequency HPF: cut the frequency range below the cutoff frequency

Balance D

L in Space D Space D R in
Balance D

2-Band EQ
Balance W Balance W

L out

Cutoff (Cutoff Frequency)


Adjust the basic frequency of the filter.
R out

2-Band EQ

LowGain
Adjust the gain of the low frequency range.

Pre Dly (Pre Delay Time)


Adjust the time delay from when the direct sound begins until the processed sound is heard.

Hi Gain
Adjust the gain of the high frequency range.

Rate #
Adjust the rate of modulation.

Balance (Effect Balance) #


Adjust the volume balance between the direct sound and the chorus sound. With a setting of D100:0W only the direct sound will be output, and with a setting of D0:100W only the chorus sound will be output.

Depth
Adjust the depth of modulation.

97

Chapter 3

2-Band EQ

Chapter 3. Creating Your Own Sounds

Level (Output Level)


Adjust the output level.

16: STEP-FLANGER
The Step Flanger effect is a flanger in which the flanger pitch changes in steps. The speed at which the pitch changes can also be specified in terms of a note-value of a specified tempo.
fig.3-62a

15: STEREO-FLANGER
This is a stereo flanger. (The LFO has the same phase for left and right.) It produces a metallic resonance that rises and falls like a jet airplane taking off or landing. A filter is provided so that you can adjust the timbre of the flanged sound.
fig.3-62

Balance D

L in Step Flanger
Feedback Feedback

2-Band EQ
Balance W

L out

Balance D

L in Flanger
Feedback Feedback

2-Band EQ
Balance W

L out

Step Flanger R in
Balance D

Balance W

2-Band EQ

R out

Flanger R in
Balance D

Balance W

Pre Dly (Pre Delay Time)


R out

2-Band EQ

Adjust the time delay from when the direct sound begins until the flanger sound is heard.

Pre Dly (Pre Delay Time)


Adjust the time delay from when the direct sound begins until the flanger sound is heard.

Rate
Adjust the rate of modulation.

Depth
Adjust the depth of modulation.

Rate #
Adjust the rate of modulation.

Fbk (Feedback Level) #


Adjust the amount (%) of the flanger sound that is returned (fed back) into the input. Negative (-) settings will invert the phase.

Depth
Adjust the depth of modulation.

Fbk (Feedback Level) #


Adjust the amount (%) of the processed sound that is returned (fed back) into the input. Positive (+) settings will return the sound in phase, and negative (-) settings will return the sound in reverse phase.

Phase
Adjust the spatial spread of the sound.

Step Rate #
Adjust the rate (period) of pitch change. This parameter can be set as a note-value of a specified tempo. In this case, specify the value of the desired note.

Phase
Adjust the spatial spread of the sound.

Filter Type
Select the type of filter. OFF: a filter will not be used LPF: cut the frequency range above the cutoff frequency HPF: cut the frequency range below the cutoff frequency

When Step Rate is Set as a Note Value


As the specified tempo, you may use either the Patch Tempo, Performance Tempo, or the tempo clock of the XP-30s system. If you want to use a fixed tempo in Patch mode (Tempo parameter setting), set the Source parameter (PATCH/ COMMON/PATCH CLOCK) to PATCH and set the desired tempo. If you want to use the systems tempo clock in Patch mode, set the Source parameter (PATCH/COMMON/ PATCH CLOCK) to SYSTEM. If you want to use a fixed tempo in Performance mode (Tempo parameter setting), set the Source parameter (PERFORM/COMMON/PERFORM CLOCK) to PERFORM and set the desired tempo. If you want to use the systems tempo clock in Performance mode, set the Source parameter (PERFORM/ COMMON/PERFORM CLOCK) to SYSTEM.

Cutoff (Cutoff Frequency)


Adjust the basic frequency of the filter.

LowGain
Adjust the gain of the low frequency range.

Hi Gain
Adjust the gain of the high frequency range.

Balance (Effect Balance)


Adjust the volume balance between the direct sound and the flanger sound. With a setting of D100:0W only the direct sound will be output, and with a setting of D0:100W only the flanger sound will be output.

Level (Output Level)


Adjust the output level.

98

Chapter 3. Creating Your Own Sounds

LowGain
Adjust the gain of the low frequency range.

Phase L (Feedback Phase Left)


Select the phase of the left delay sound. NORMAL: Phase is not changed. INVERT: Phase is inverted.

Hi Gain
Adjust the gain of the high frequency range.

Balance (Effect Balance)


Adjust the volume balance between the direct sound and the flanger sound. With a setting of D100:0W only the direct sound will be output, and with a setting of D0:100W only the chorus sound will be output.

Phase R (Feedback Phase Right)


Select the phase of the right delay sound. NORMAL: Phase is not changed. INVERT: Phase is inverted.

HF Damp
Adjust the frequency above which sound fed back to the effect will be cut. If you do not want to cut the high frequencies of the feedback, set this parameter to BYPASS.

Level (Output Level)


Adjust the output level.

17: STEREO-DELAY
This is a stereo delay. When Feedback Mode is NORMAL:
fig.3-63a

LowGain
Adjust the gain of the low frequency range.

Hi Gain
Adjust the gain of the high frequency range.
L out

Balance D

L in Delay
Feedback Feedback

2-Band EQ
Balance W

Balance (Effect Balance) #

Delay R in
Balance D

Balance W

2-Band EQ

R out

Level (Output Level)


Adjust the output level.

When Feedback Mode is CROSS:


fig.3-63b

Balance D

L in Delay
Feedback Feedback

2-Band EQ
Balance W

18: MODULATION-DELAY
L out

This effect adds modulation to the delayed sound, producing an effect similar to a flanger. When Feedback Mode is NORMAL:
fig.3-63c

Balance D

Delay R in
Balance D

Balance W

L in R out Delay
Feedback Feedback

2-Band EQ
Balance W

L out

2-Band EQ

Modulation

Delay L (Delay Time Left)


Adjust the time from the original sound until when the left delay sound is heard.

Delay R in

Modulation
Balance D

Balance W

Delay R (Delay Time Right)


Adjust the time from the original sound until when the right delay sound is heard.
fig.3-63d

2-Band EQ

R out

When Feedback Mode is CROSS:


Balance D

Fbk (Feedback Level) #


Adjust the proportion (%) of the delay sound that is fed back into the effect. Negative (-) settings will invert the phase.

L in Delay
Feedback Feedback

2-Band EQ
Balance W

L out

Modulation

Mode (Feedback Mode)


Select the way in which delay sound is fed back into the effect. NORMAL: The left delay sound will be fed back into the left delay, and the right delay sound into the right delay. CROSS: The left delay sound will be fed back into the right delay, and the right delay sound into the left delay.
R in

Delay

Modulation
Balance D

Balance W

2-Band EQ

R out

Delay L (Delay Time Left)


Adjust the time from the original sound until when the left delay sound is heard.

99

Chapter 3

Adjust the volume balance between the direct sound and the delay sound. With a setting of D100:0W only the direct sound will be output, and with a setting of D0:100W only the delay sound will be output.

Chapter 3. Creating Your Own Sounds

Delay R (Delay Time Right)


Adjust the time from the original sound until when the right delay sound is heard.

Delay C (Delay Time Center) Delay L (Delay Time Left) Delay R (Delay Time Right)
Adjust the time delay from the direct sound until when the delay sound is heard. This parameter can be set as a notevalue of a specified tempo. In this case, specify the value of the desired note.

Fbk (Feedback Level)


Adjust the proportion (%) of the delay sound that is fed back into the effect. Negative (-) settings will invert the phase.

Mode (Feedback Mode)


Select the way in which delay sound is fed back into the effect. NORMAL: The left delay sound will be fed back into the left delay, and the right delay sound into the right delay. CROSS: The left delay sound will be fed back into the right delay, and the right delay sound into the left delay.

When Step Rate is Set as a Note Value


As the specified tempo, you may use either the Patch Tempo, Performance Tempo, or the tempo clock of the XP-30s system. If you want to use a fixed tempo in Patch mode (Tempo parameter setting), set the Source parameter (PATCH/ COMMON/PATCH CLOCK) to PATCH and set the desired tempo. If you want to use the systems tempo clock in Patch mode, set the Source parameter (PATCH/COMMON/ PATCH CLOCK) to SYSTEM. If you want to use a fixed tempo in Performance mode (Tempo parameter setting), set the Source parameter (PERFORM/COMMON/PERFORM CLOCK) to PERFORM and set the desired tempo. If you want to use the systems tempo clock in Performance mode, set the Source parameter (PERFORM/COMMON/PERFORM CLOCK) to SYSTEM.

Rate #
Adjust the speed of the modulation.

Depth
Adjust the depth of the modulation.

Phase
Adjust the spatial spread of the sound.

HF Damp
Adjust the frequency above which sound fed back to the effect will be cut. If you do not want to cut the high frequencies of the feedback, set this parameter to BYPASS.

LowGain
Adjust the gain of the low frequency range.

Hi Gain
Adjust the gain of the high frequency range.

Fbk (Feedback Level) #


Adjust the proportion (%) of the delay sound that is fed back into the effect. Negative (-) settings will invert the phase.

Balance (Effect Balance) #


Adjust the volume balance between the direct sound and the modulation delay sound. With a setting of D100:0W only the direct sound will be output, and with a setting of D0:100W only the modulation delay sound will be output.

Level C (Center Level) Level L (Left Level) Level R (Right Level)


Adjust the volume of each delay sound.

Level (Output Level)


Adjust the output level.

HF Damp
Adjust the frequency above which sound fed back to the effect will be cut. If you do not want to cut the high frequencies of the feedback, set this parameter to BYPASS.

19: TRIPLE-TAP-DELAY
The Triple Tap Delay produces three delay sounds; center, left and right. The center delay time can be specified as a note value of a specified tempo.
fig.3-64

LowGain
Adjust the gain of the low frequency range.

Balance D

L in
Left Tap Triple Tap Delay Feedback Center Tap

2-Band EQ
Balance W

Hi Gain
L out

Adjust the gain of the high frequency range.

Balance (Effect Balance) #


Adjust the volume balance between the direct sound and the delay sound. With a setting of D100:0W only the direct sound will be output, and with a setting of D0:100W only the delay sound will be output.

Right Tap Balance D

Balance W

R in

2-Band EQ

R out

100

Chapter 3. Creating Your Own Sounds

Level (Output Level)


Adjust the output level.

20: QUADRUPLE-TAP-DELAY
The Quadruple Tap Delay has four delays. Each of the Delay Time parameters can be specified as a note length of the selected tempo.
fig.3-65a

Level Level Level Level

1 2 3 4

Adjust the volume of each delay sound.

Fbk (Feedback Level) #


Adjust the proportion (%) of the delay sound that is fed back into the effect. Negative (-) settings will invert the phase.

Balance D

L in
Delay 1 Feedback Delay 2

L out
Balance W

HF Damp
Adjust the frequency above which sound fed back to the effect will be cut. If you do not want to cut the high frequencies of the feedback, set this parameter to BYPASS.

Quadruple Tap Delay


Delay 3 Delay 4 Balance W

Balance (Effect Balance) #


Adjust the volume balance between the direct sound and the delay sound. With a setting of D100:0W only the direct sound will be output, and with a setting of D0:100W only the delay sound will be output.

R in
Balance D

R out

The stereo location of each delay sound is as follows.


fig.3-65b

2 1 L

3 4 R

Level (Output Level)


Adjust the output level.

Delay Delay Delay Delay

1 2 3 4

(Delay (Delay (Delay (Delay

Time Time Time Time

1) 2) 3) 4)

21: TIME-CONTROL-DELAY
This effect allows you to use a specified controller (the controller selected in EFX Control Source) to control the delay time and pitch in realtime. Lengthening the delay will lower the pitch, and shortening it will raise the pitch.
fig.3-66

Adjust the time delay from the direct sound until when each delay sound is heard. These parameters can be set as a notevalue of a specified tempo. In this case, specify the value of the desired note.

L in

Balance D

2-Band EQ
Balance W

L out

Time Control Delay


Balance W

When Step Rate is Set as a Note Value


As the specified tempo, you may use either the Patch Tempo, Performance Tempo, or the tempo clock of the XP-30s system. If you want to use a fixed tempo in Patch mode (Tempo parameter setting), set the Source parameter (PATCH/ COMMON/PATCH CLOCK) to PATCH and set the desired tempo. If you want to use the systems tempo clock in Patch mode, set the Source parameter (PATCH/COMMON/ PATCH CLOCK) to SYSTEM. If you want to use a fixed tempo in Performance mode (Tempo parameter setting), set the Source parameter (PERFORM/COMMON/PERFORM CLOCK) to PERFORM and set the desired tempo. If you want to use the systems tempo clock in Performance mode, set the Source parameter (PERFORM/COMMON/PERFORM CLOCK) to SYSTEM.

Feedback

R in
Balance D

2-Band EQ

R out

Delay (Delay time) #


Adjust the time delay from the direct sound until when each delay sound is heard.

Accel (Acceleration)
This parameter adjusts the time over which the Delay Time will change from the current setting to a newly specified setting. The rate of change for the Delay Time directly affects the rate of pitch change.

Fbk (Feedback Level) #


Adjust the proportion (%) of the delay sound that is fed back into the effect. Negative (-) settings will invert the phase.

HF Damp
Adjust the frequency above which sound fed back to the effect will be cut. If you do not want to cut the high frequencies of the feedback, set this parameter to BYPASS.

Pan (Output Pan)


Adjust the stereo location of the delay sound. L64 is far left, 0 is center, and 63R is far right.

101

Chapter 3

Chapter 3. Creating Your Own Sounds

LowGain
Adjust the gain of the low frequency range.

PreDlyB (Pre Delay Time B)


Adjust the time delay from when the direct sound begins until the Pitch Shift A sound is heard.

Hi Gain
Adjust the gain of the high frequency range.

Mode (Pitch Shifter Mode)


Higher settings of this parameter will result in slower response, but steadier pitch.

Balance (Effect Balance)


Adjust the volume balance between the direct sound and the delay sound. With a setting of D100:0W only the direct sound will be output, and with a setting of D0:100W only the delay sound will be output.

Lvl Bal (Level Balance)


Adjust the volume balance between the Pitch Shift A and Pitch Shift B sounds.

Level (Output Level)


Adjust the output level.

Balance (Effect Balance)


Adjust the volume balance between the direct sound and the pitch shift sound. With a setting of D100:0W only the direct sound will be output, and with a setting of D0:100W only the pitch shift sound will be output.

22: 2VOICE-PITCH-SHIFTER
A Pitch Shifter shifts the pitch of the original sound. This 2voice pitch shifter has two pitch shifters, and can add two pitch shifted sounds to the original sound.
fig.3-67

Level (Output Level)


Adjust the output level.

Balance D

L in
Level Balance A PanA L PanA R PanB L PanB R Balance D

L out
Balance W

23: FBK-PITCH-SHIFTER (Feedback Pitch Shifter)


This pitch shifter allows the pitch shifted sound to be fed back into the effect.
fig.3-68

2Voice Pitch Shifter

Level Balance B

Balance W

L in

Balance D

2-Band EQ
Balance W

L out

R in

R out Pitch Shifter

CoarseA (Coarse Pitch A) #1


Adjust the pitch of Pitch Shift A in semitone steps (-2+1 octaves).
R in

Balance W Feedback Balance D

2-Band EQ

R out

Coarse (Coarse Pitch) #1


Adjust the pitch of the pitch shifted sound in semitone steps (-2+1 octaves).

Fine A (Fine Pitch A) #1


Make fine adjustments to the pitch of Pitch Shift A in 2-cent steps (-100+100 cents). * One cent is 1/100th of a semitone.

Fine (Fine Pitch) #1


Make fine adjustments to the pitch of the pitch shifted sound in 2-cent steps (-100+100 cents). * One cent is 1/100th of a semitone.

Pan A (Output Pan A)


Adjust the stereo location of the Pitch Shift A sound. L64 is far left, 0 is center, and 63R is far right.

Fbk (Feedback Level) #


Adjust the proportion (%) of the processed sound that is fed back into the effect. Negative (-) settings will invert the phase.

PreDlyA (Pre Delay Time A)


Adjust the time delay from when the direct sound begins until the Pitch Shift A sound is heard.

Pre Dly (Pre Delay Time)


Adjust the time delay from when the direct sound begins until the pitch shifted sound is heard.

CoarseB (Coarse Pitch B) #2


Adjust the pitch of Pitch Shift B in semitone steps (-2+1 octaves).

Mode (Pitch Shifter Mode)


Higher settings of this parameter will result in slower response, but steadier pitch.

Fine B (Fine Pitch B) #2


Make fine adjustments to the pitch of Pitch Shift B in 2-cent steps (-100+100 cents). * One cent is 1/100th of a semitone.

Pan (Output Pan)


Adjust the stereo location of the pitch shifted sound. L64 is far left, 0 is center, and 63R is far right.

Pan B (Output Pan B)


Adjust the stereo location of the Pitch Shift B sound. L64 is far left, 0 is center, and 63R is far right.

LowGain
Adjust the gain of the low frequency range.

102

Chapter 3. Creating Your Own Sounds

Hi Gain
Adjust the gain of the high frequency range.

25: GATE-REVERB
Gate Reverb is a special type of reverb in which the reverberant sound is cut off before its natural length.
fig.3-70

Balance (Effect Balance)


Adjust the volume balance between the direct sound and the pitch shift sound. With a setting of D100:0W only the direct sound will be output, and with a setting of D0:100W only the pitch shift sound will be output.

L in

Balance D

2-Band EQ
Balance W

L out

Gate Reverb
Balance W

Level (Output Level)


Adjust the output level.

R in
Balance D

2-Band EQ

R out

24: REVERB
The Reverb effect adds reverberation to the sound, simulating an acoustic space.
fig.3-69

Type (Gate Reverb Type)


Select the type of reverb. NORMAL: conventional gate reverb REVERSE: backwards reverb SWEEP1: the reverberant sound moves from right to left SWEEP2: the reverberant sound moves from left to right

L in

Balance D

2-Band EQ
Balance W

L out

Reverb
Balance W

Pre Dly (Pre Delay Time)


R out

R in
Balance D

2-Band EQ

Adjust the time delay from when the direct sound begins until the reverb sound is heard. Adjust the time from when the reverb is heard until when it disappears.

Type (Reverb Type)


Select the type of Reverb effect. ROOM1:dense reverb with short decay ROOM2:sparse reverb with short decay STAGE1:reverb with greater late reverberation STAGE2:reverb with strong early reflections HALL1:reverb with clear reverberance HALL2:reverb with rich reverberance

LowGain
Adjust the gain of the low frequency range.

Hi Gain
Adjust the gain of the high frequency range.

Balance (Effect Balance) #


Adjust the volume balance between the direct sound and the reverb sound. With a setting of D100:0W only the direct sound will be output, and with a setting of D0:100W only the reverb sound will be output.

Pre Dly (Pre Delay Time)


Adjust the time delay from when the direct sound begins until the reverb sound is heard.

Time (Reverb Time) #


Adjust the time length of reverberation.

Level (Output Level) #


Adjust the output level.

HF Damp
Adjust the frequency above which the reverberant sound will be cut. As the frequency is set lower, more of the high frequencies will be cut, resulting in a softer and more muted reverberance. If you do not want the high frequencies to be cut, set this parameter to BYPASS.

26: OVERDRIVECHORUS
This effect connects an overdrive and a chorus in series.
fig.3-71

L in Overdrive R in

L out
Balance D Balance W

Chorus
Balance W

LowGain
Adjust the gain of the low frequency range.

R out
Balance D

Hi Gain
Adjust the gain of the high frequency range.

OD Drive
Adjust the degree of overdrive distortion. The volume will change together with the degree of distortion.

Balance (Effect Balance) #


Adjust the volume balance between the direct sound and the reverb sound. With a setting of D100:0W only the direct sound will be output, and with a setting of D0:100W only the reverb sound will be output.

OD Pan (Overdrive Pan) #


Adjust the stereo location of the overdrive sound. L64 is far left, 0 is center, and 63R is far right.

Cho Dly (Chorus Pre Delay Time)


Adjust the time delay from when the direct sound begins until the chorus sound is heard.

Level (Output Level)


Adjust the output level.

103

Chapter 3

Gate Time

Chapter 3. Creating Your Own Sounds

ChoRate (Chorus Rate)


Adjust the modulation speed of the chorus effect.

28: OVERDRIVEDELAY
This effect connects an overdrive and a delay in series.
fig.3-73

Chorus Depth
Adjust the modulation depth of the chorus effect.

L in
Balance D

L out
Balance W

Chorus Balance #
Adjust the volume balance between the overdrive sound that is sent through the chorus and the overdrive sound that is not sent through the chorus. With a setting of D100: 0W, only the overdrive sound will be output. With a setting of D0: 100W, only the overdrive sound that is sent through the chorus will be output.
R in

Overdrive

Delay
Balance W Feedback

R out
Balance D

OD Drive
Adjust the degree of overdrive distortion. The volume will change together with the degree of distortion.

Level (Output Level)


Adjust the output level.

OD Pan (Overdrive Pan) #


Adjust the stereo location of the overdrive sound. L64 is far left, 0 is center, and 63R is far right.

27: OVERDRIVEFLANGER
This effect connects an overdrive and a flanger in series.
fig.3-72

DlyTime (Delay Time)


Adjust the time delay from when the direct sound begins until the delay sound is heard.

Balance D

L in
Feedback

L out
Balance W Balance W

Dly Fbk (Delay Feedback Level)


Adjust the proportion (%) of the delay sound that is fed back into the effect. Negative (-) settings will invert the phase.

Overdrive

Flanger

R in
Balance D

R out

Delay HF Damp
Adjust the frequency above which delayed sound fed back to the effect will be cut. If you do not want to cut the high frequencies of the feedback, set this parameter to BYPASS.

OD Drive
Adjust the degree of overdrive distortion. The volume will change together with the degree of distortion.

OD Pan (Overdrive Pan) #


Adjust the stereo location of the overdrive sound. L64 is far left, 0 is center, and 63R is far right.

Delay Balance (Delay Balance) #


Adjust the volume balance between the overdrive sound that is sent through the delay and the overdrive sound that is not sent through the delay. With a setting of D100: 0W, only the overdrive sound will be output. With a setting of D0: 100W, only the overdrive sound that is sent through the delay will be output.

Flg Dly (Flanger Pre Delay Time)


Adjust the time delay from when the direct sound begins until the flanger sound is heard.

FlgRate (Flanger Rate)


Adjust the modulation speed of the flanger effect.

Level (Output Level)


Adjust the output level.

Flg Dpt (Flanger Depth)


Adjust the modulation depth of the flanger effect.

29: DISTORTIONCHORUS
This effect connects distortion and chorus in series. The parameters are essentially the same as 26: OVERDRIVECHORUS, with the exception of the following two. OD Drive Dist Drive (Specify the amount of distortion.) OD Pan Dist Pan (Specify the stereo location of the distortion sound.)
fig.3-74

Flg Fbk (Flanger Feedback Level)


Adjust the proportion (%) of the flanger sound that is fed back into the effect. Negative (-) settings will invert the phase.

Flanger Balance #
Adjust the volume balance between the overdrive sound that is sent through the flanger and the overdrive sound that is not sent through the flanger. With a setting of D100: 0W, only the overdrive sound will be output. With a setting of D0: 100W, only the overdrive sound that is sent through the flanger will be output.

L in Distortion R in

L out
Balance D Balance W

Chorus
Balance W

Level (Output Level)


Adjust the output level.

R out
Balance D

104

Chapter 3. Creating Your Own Sounds

30: DISTORTIONFLANGER
This effect connects distortion and flanger in series. The parameters are essentially the same as in 27: OVERDRIVEFLANGER, with the exception of the following two. OD Drive Dist Drive (Specify the amount of distortion.) OD Pan Dist Pan (Specify the stereo location of the distortion sound.)
fig.3-75

Chorus Depth
Adjust the modulation depth of the chorus effect.

Chorus Balance #
Adjust the volume balance between the enhancer sound that is sent through the chorus and the enhancer sound that is not sent through the chorus. With a setting of D100: 0W, only the enhancer sound will be output. With a setting of D0: 100W, only the enhancer sound that is sent through the chorus will be output.

Balance D

L in
Feedback

L out
Balance W Balance W

Level (Output Level)


Adjust the output level.

Distortion

Flanger

33: ENHANCERFLANGER
This effect connects an enhancer and a flanger in series.
fig.3-78

R in
Balance D

R out

31: DISTORTIONDELAY
This effect connects distortion and delay in series. The parameters are essentially the same as in 28: OVERDRIVEDELAY, with the exception of the following two. OD Drive Dist Drive (Specify the amount of distortion.) OD Pan Dist Pan (Specify the stereo location of the distortion sound.)
fig.3-76

Balance D

L in

Enhancer
Mix Feedback

L out
Balance W

Flanger R in Enhancer
Mix Balance D

R out

Enhancer Sens #
Adjust the sensitivity of the enhancer.

L in
Balance D

L out
Balance W

Enhancer Mix (Enhancer Mix Level)


Adjust the ratio with which the overtones generated by the enhancer are combined with the direct sound.

Distortion

Delay
Balance W Feedback

Flg Dly (Flanger Pre Delay Time)


Adjust the time delay from when the direct sound begins until the flanger sound is heard.

R in
Balance D

R out

32: ENHANCERCHORUS
This effect connects an enhancer and a chorus in series.
fig.3-77

FlgRate (Flanger Rate)


Adjust the modulation speed of the flanger effect.
L out

L in

Enhancer
Mix Balance D

Flg Dpt (Flanger Depth)


Adjust the modulation depth of the flanger effect.

Balance W

Chorus
Balance W

Flg Fbk (Flanger Feedback Level)


Adjust the proportion (%) of the flanger sound that is fed back into the effect. Negative (-) settings will invert the phase.

R in

Enhancer
Mix Balance D

R out

Enhancer Sens #
Adjust the sensitivity of the enhancer.

Flanger Balance #
Adjust the volume balance between the enhancer sound that is sent through the flanger and the enhancer sound that is not sent through the flanger. With a setting of D100: 0W, only the enhancer sound will be output. With a setting of D0: 100W, only the enhancer sound that is sent through the flanger will be output.

Enhancer Mix (Enhancer Mix Level)


Adjust the ratio with which the overtones generated by the enhancer are combined with the direct sound.

Cho Dly (Chorus Pre Delay Time)


Adjust the time delay from when the direct sound begins until the chorus sound is heard.

Level (Output Level)


Adjust the output level.

ChoRate (Chorus Rate)


Adjust the modulation speed of the chorus effect.

105

Chapter 3

Balance W

Chapter 3. Creating Your Own Sounds

34: ENHANCERDELAY
This effect connects an enhancer and a delay in series.
fig.3-79

Cho Bal (Chorus Balance) #


Adjust the volume balance between the direct sound and the chorus sound. With a setting of D100: 0W, only the direct sound will be output. With a setting of D0: 100W, only the chorus sound will be output.

L in

Enhancer
Mix Balance D

L out
Balance W

Delay
Balance W Feedback

DlyTime (Delay Time)


Adjust the time delay from when the direct sound begins until the delay sound is heard.

R in

Enhancer
Mix Balance D

R out

Enhancer Sens #
Adjust the sensitivity of the enhancer.

Dly Fbk (Delay Feedback Level)


Adjust the proportion (%) of the delay sound that is fed back into the delay input. Negative (-) settings will invert the phase.

Enhancer Mix (Enhancer Mix Level)


Adjust the ratio with which the overtones generated by the enhancer are combined with the direct sound.

Delay HF Damp
Adjust the frequency above which delayed sound fed back to the delay input will be cut. If you do not want to cut the high frequencies of the feedback, set this parameter to BYPASS.

DlyTime (Delay Time)


Adjust the time delay from when the direct sound begins until the delay sound is heard.

Delay Balance #
Adjust the volume balance between the chorus sound that is sent through the delay and the chorus sound that is not sent through the delay. With a setting of D100: 0W, only the chorus sound will be output. With a setting of D0: 100W, only the chorus sound that is sent through the delay will be output.

Dly Fbk (Delay Feedback Level)


Adjust the proportion (%) of the delay sound that is fed back into the delay input. Negative (-) settings will invert the phase.

Delay HF Damp
Adjust the frequency above which delayed sound fed back to the delay input will be cut. If you do not want to cut the high frequencies of the delay feedback, set this parameter to BYPASS.

Level (Output Level)


Adjust the output level.

Delay Balance #
Adjust the volume balance between the enhancer sound that is sent through the delay and the enhancer sound that is not sent through the delay. With a setting of D100: 0W, only the enhancer sound will be output. With a setting of D0: 100W, only the enhancer sound that is sent through the delay will be output.

36: FLANGERDELAY
This effect connects a flanger and a delay in series.
fig.3-81

Balance D

L in
Feedback Balance D Balance W Balance W

L out
Balance W

Flanger R in
Balance D

Delay
Balance W Feedback

R out
Balance D

Level (Output Level)


Adjust the output level.

Flg Dly (Flanger Pre Delay Time)


Adjust the time delay from when the direct sound begins until the flanger sound is heard.

35: CHORUSDELAY
This effect connects a chorus and a delay unit in series.
fig.3-80

FlgRate (Flanger Rate)


Adjust the modulation speed of the flanger effect.

Balance D

L in
Balance D Balance W

L out
Balance W

Flg Dpt (Flanger Depth)


Adjust the modulation depth of the flanger effect.

Chorus
Balance W

Delay
Balance W Feedback

Flg Fbk (Flanger Feedback Level)


Adjust the proportion (%) of the flanger sound that is fed back into the effect. Negative (-) settings will invert the phase.

R in
Balance D Balance D

R out

Cho Dly (Chorus Pre Delay Time)


Adjust the time delay from when the direct sound begins until the chorus sound is heard.

Flg Bal (Flanger Balance) #


Adjust the volume balance between the direct sound and the flanger sound. With a setting of D100: 0W, only the direct sound will be output. With a setting of D0: 100W, only the flanger sound will be output.

ChoRate (Chorus Rate)


Adjust the modulation speed of the chorus effect.

DlyTime (Delay Time)


Adjust the time delay from when the direct sound begins until the delay sound is heard.

Cho Dpt (Chorus Depth)


Adjust the modulation depth of the chorus effect.

106

Chapter 3. Creating Your Own Sounds

Dly Fbk (Delay Feedback Level)


Adjust the proportion (%) of the delay sound that is fed back into the delay input. Negative (-) settings will invert the phase.

Flanger Balance #
Adjust the volume balance between the chorus sound and the chorus sound that is passed through the flanger. With a setting of D100: 0W, only the chorus sound will be output. With a setting of D0: 100W, only the chorus sound that passes through the flanger will be output.

HF Damp
Adjust the frequency above which delayed sound fed back to the delay input will be cut. If you do not want to cut the high frequencies of the delay feedback, set this parameter to BYPASS.

Level (Output Level)


Adjust the output level.

Delay Balance #
Adjust the volume balance between the flanger sound that is sent through the delay and the flanger sound that is not sent through the delay. With a setting of D100: 0W, only the flanger sound will be output. With a setting of D0: 100W, only the flanger sound that is sent through the delay will be output.

38: CHORUS/DELAY
This effect connects a chorus and a delay in parallel. The parameters are the same as for 35: CHORUSDELAY. However, the Delay Balance parameter adjusts the volume balance between the direct sound and the delay sound.
fig.3-83

Level (Output Level)


Adjust the output level.

Balance D

L in Chorus
Feedback

L out
Balance W

37: CHORUSFLANGER
This effect connects a chorus and a flanger in series.
fig.3-82

Delay
Balance D Balance D

Balance W

L in
Balance W Feedback

L out
Balance W

R in
Balance D

R out

Chorus
Balance W

Flanger
Balance W

39: FLANGER/DELAY
This effect connects a flanger and a delay in parallel. The parameters are the same as for 36: FLANGERDELAY. However, the Delay Balance parameter adjusts the volume balance between the direct sound and the delay sound.
fig.3-84

R in
Balance D Balance D

R out

Cho Dly (Chorus Pre Delay Time)


Adjust the time delay from when the direct sound begins until the chorus sound is heard.

Balance D

L in

L out Flanger
Feedback Feedback Balance W

ChoRate (Chorus Rate)


Adjust the modulation speed of the chorus effect.

Cho Dpt (Chorus Depth)


Adjust the modulation depth of the chorus effect.

Delay R in
Balance D

Balance W

Cho Bal (Chorus Balance) #


Adjust the volume balance between the direct sound and the chorus sound. With a setting of D100: 0W, only the direct sound will be output. With a setting of D0: 100W, only the chorus sound will be output.

R out

40: CHORUS/FLANGER
This effect connects a chorus and a flanger in parallel. The parameters are the same as for 37: CHORUSFLANGER. However, the Flanger Balance parameter adjusts the volume balance between the direct sound and the flanger sound.
fig.3-85

Flg Dly (Flanger Pre Delay Time)


Adjust the time delay from when the direct sound begins until the flanger sound is heard.

Balance D

FlgRate (Flanger Rate)


Adjust the modulation speed of the flanger effect.

L in Chorus
Feedback

L out
Balance W

Flg Dpt (Flanger Depth)


Adjust the modulation depth of the flanger effect.

Flanger R in
Balance D

Balance W

Flg Fbk (Flanger Feedback Level)


Adjust the proportion (%) of the flanger sound that is fed back into the effect. Negative (-) settings will invert the phase.

R out

107

Chapter 3

Chapter 3. Creating Your Own Sounds

XP-30 Operating Environment Setup (System Parameters and Their Functions)


fig.3-86

s Arpeggio Settings (ARPEGGIO)


This is where to set Arpeggiator parameters.

ARPEGGIO
Style
Sets the style of the arpeggio. Select from the following 43 options. For creating your own style, choose LIMITLESS. 1/4: The rhythm will be divided in quarter notes. 1/6: The rhythm will be divided in quarter note triplets. 1/8: The rhythm will be divided in eighth notes. 1/12: The rhythm will be divided in eighth note triplets. 1/16: The rhythm will be divided in 16th notes. 1/32: The rhythm will be divided in 32nd notes. PORTAMENTO A, B: A style using the portamento effect. GLISSANDO: A glissando style. SEQUENCE AD: Styles for sequenced patterns. ECHO: An echo-like style. SYNTH BASS, SLAP BASS A, SLAP BASS B, WALK BASS: Styles appropriate for bass playing. RHYTHM GTR AE: Styles for guitar cutting. Styles BE are effective when 34 notes are held. 3 FINGER GTR: Three-finger guitar style. STRUMMING GTR: A style simulating a guitar chord strummed upward (downward). Effective when 56 notes are held. KBD COMPING A, B: Styles for keyboard instrument backing. KBD COMPING C, D: Styles in triple meter. KBD COMPING E: A reggae-type style. Effective when 3 notes are held. PERCUSSION: A style suitable for percussive instrument sounds. HARP: The playing style of a harp. SHAMISEN: The playing style of a Shamisen. BOUND BALL: A style suggestive of a bouncing ball. RANDOM: A style in which the notes sound in random order. BOSSANOVA: A style with bossanova guitar cutting. Hold 34 notes for best results. You can increase the tempo and use this as a Samba. SALSA: Typical salsa style. Hold 34 notes for best results. MAMBO: Typical mambo style. Hold 34 notes for best results. LATIN PERCUSION: A rhythm style with Latin percussion instruments such as Clave, Cowbell, Clap, Bongo, Conga, Agogo etc. SAMBA: Typical samba style. Use for rhythm patterns or bass lines. TANGO: Typical tango rhythm style. Hold the root, 3rd and 5th of a triad etc. for best results. HOUSE: A style for house piano backing. Hold 34 notes for best results.

s Display Screen Contrast and Clock Settings (SETUP)


SYSTEM SETUP
LCD Contrast
Adjust the contrast (brighthess) of the display.

Power Up Mode
Select the condition that the XP-30 will be in when the power is turned on. LAST-SET: The XP-30 will be in the condition it was in when power was last turned off. DEFAULT: The XP-30 will be ready to play Patch USER:001.

Patch Remain (Patch Remain Switch)


If you want currently-sounding notes to be turned off when a new Patch (Rhythm Set) is selected, set this parameter OFF. * Effects settings change as soon as you switch to a new Patch or Rhythm Set, without being influenced by the Patch Remain setting. Because of this, certain effects settings can cause notes that were until then sounding to no longer be heard, even though Patch Remain has been set to on.

Clock Source
Specify the tempo clock of the system. INT: The internal clock will be the tempo clock for the system. MIDI: An external clock will be the tempo clock for the system.

System Tempo
Set the system tempo. * When Clock Source is set to MIDI, the tempo will synchronize to the clock messages received from an external MIDI device, so it will not be possible to set the tempo value. The tempo of the external clock will be displayed in parentheses.

Category Select Mode


When searching for patches, specify the patch that will be selected when you press the numeric key. LAST-SET: The patch last-selected during the previous patch search will be selected. DEFAULT: The patch specified as the factory default will be selected.

108

Chapter 3. Creating Your Own Sounds

LIMITLESS: The settings of all parameters can be freely combined without restriction. * Choices can be set for the Motif, Beat Pattern, Shuffle Rate and Accent Rate parameters for each style. Refer to the Arpeggio Style List (p. 182).

Octave Range
Sets the key range in octaves over which arpeggio will take place. If you want the arpeggio to sound using only the notes that you actually play, set this parameter to 0. To have the arpeggio sound using the notes you play and notes 1 octave higher, set this parameter to +1. A setting of -1 will make the arpeggio sound using the notes you play and notes l octave lower.

Motif
Sets the order in which notes of the chord will sound. Some settings will not be available depending on the Style parameter setting. SINGLE UP: Notes will sound singly, starting from the lowest key pressed. SINGLE DOWN: Notes will sound singly, starting from the highest key pressed. SINGLE UP&DOWN: Notes will sound singly, starting from the lowest key pressed, going up and then back down. SINGLE RANDOM: Notes will sound singly in random order. DUAL UP: Notes will sound in pairs, starting from the lowest key pressed. DUAL DOWN: Notes will sound in pairs, starting from the highest key pressed. DUAL UP&DOWN: Notes will sound in pairs, starting from the lowest key pressed, going up and then back down. DUAL RANDOM: Notes will sound in pairs, in random order. TRIPLE UP: Notes you press will sound three at a time, from low to high. TRIPLE DOWN: Notes you press will sound three at a time, from high to low. TRIPLE UP&DOWN: Notes you press will sound three at a time, from low to high and then back down from high to low. TRIPLE RANDOM: Notes you press will sound three at a time, in random order. NOTE ORDER: Notes will sound in the order that they were pressed. Up to 32 notes can be stored, so you can create melody lines by pressing keys in the appropriate order.

Notes will be played in an ascending and descending chromatic scale between the lowest and the highest keys that are pressed. Simply press two notes, the lowest and highest. CHORD: All notes that are pressed will sound simultaneously. BASS+CHORD15: The lowest note that is pressed and other notes will sound as a chord. BASS+UP18: The lowest note that is pressed and other notes will sound as an arpeggio. BASS+RANDOM13: The lowest note that is pressed and other notes will sound randomly. TOP+UP16: The highest note that is pressed and other notes will sound as an arpeggio. BASS+UP+TOP: Simulated fingering of folk guitars three-finger picking technique. GLISSANDO:

Beat Pattern
Select the beat pattern from the choices below. This setting will affect the location of the accent and length of the notes to determine the beat (rhythm). Some settings will not be available depending on the Style parameter setting. 1/4, 1/6, 1/8, 1/12, 1/16 13, 1/32 13, PORTA-A 0111, PORTA-B 0115, SEQ-A 17, SEQ-B 15, SEQ-C 12, SEQ-D 18, ECHO 13, MUTE 0116, STRUM18, REGGAE12, REFRAIN12, PERC14, WALKBS, HARP, BOUND, RANDOM, BOSSA NOVA, SALSA 14, MAMBO 12, CLAVE, REV CLA, GUIRO, AGOGO, SAMBA, TANGO 14, HOUSE 12

Accent Rate
Modifies the strength of accents and the length of the notes to adjust the groove feel of the arpeggio. A setting of 100% will produce the most pronounced groove feel.

Shuffle Rate
This parameter allows you to modify the timing of an upbeat between two down-notes next to each other, to create shuffle rhythms. With a setting of 50%, the notes will be spaced evenly. Higher values will give more of a dotted (shuffle) feel.

Key Velocity
Sets the force of the chord. If you wish to use the velocity at which the notes are actually played, set this parameter to REAL. To use a constant velocity regardless of the force with which you play the keyboard, choose a desired value from 1 127.

109

Chapter 3

Chapter 3. Creating Your Own Sounds

Part (Arpeggio Part)


When using a Layer performance, you can use this parameter to specify the Part for playing an arpeggio. Parts other than that you specify will sound as you play on the keyboard. * This setting will be invalid if Single performance, Patch mode or Rhythm Set mode is selected.

HOLD PEDAL
Set the function of the pedal connected to the HOLD PEDAL jack.

Output (Pedal Output)


Select the sound source(s) (the internal sound source and/or external sound sources connected to MIDI OUT connector) which will be controlled by the pedal. OFF: Neither will be controlled. INT: Only the internal sound source will be controlled. MIDI: Only external sound sources will be controlled. BOTH: Both the internal sound source and external sound sources will be controlled.

Tempo
Sets the speed of the arpeggio. This setting is the same as the tempo of the song. Changing this setting will also affect the songs playback tempo. When the Clock Source parameter (SYSTEM/SETUP/ SYSTEM SETUP) is set to INT, the display will indicate Tempo(=SYS), and this will be the same value as the system tempo. With a setting of MIDI, the display will indicate Tempo(=EXT), and you will be synchronized to the clock of the external MIDI device.

Polarity (Pedal Polarity)


This parameter switches the polarity of the Hold pedal. On some pedals, the electrical signal output by the pedal when it is pressed or released is the opposite of other pedals. If your pedal has an effect opposite of what you expect, set this parameter to REVERSE. If you are using a Roland pedal (that has no polarity switch), set this parameter to STANDARD.

s Keyboard and Controllers Settings (CONTROL)


KEYBOARD
Transpose (Transpose Switch/Value)
If you wish to transpose the range of the keyboard, turn this switch ON and set the desired amount of transposition (in semitone steps). Tonic is indicated in parentheses ( ). * The transposed note name will be shown in the lower right of the Performance/Patch/Rhythm Set play display. * When transposing the keyboard range, press [TRANSPOSE] and indicator lights. * To change transpose amount on a PLAY display, hold down [TRANSPOSE] and press [-OCT] or [+OCT].

CONTROL PEDAL
Assign the function of the pedals connected to the CONTROL PEDAL jack.

Assign (Pedal Assign)


Select the function controlled by the pedal. CC0195: Controller numbers 195 (except for 6, 3263). PITCH BEND: Pitch bend AFTERTOUCH: Aftertouch PROG-UP: Every press of the pedal selects the next Performance number, Patch number, or Rhythm Set. PROG-DOWN: Every press of the pedal selects the previous Performance number, Patch number, or Rhythm Set. TAP-TEMPO: Tap tempo (a tempo specified by the interval at which you press the pedal). OCT-UP: Each pedal press raises the key range in octave steps (up to 3 octaves higher). OCT-DOWN: Each pedal press lowers the key range in octave steps (up to 3 octaves lower).

Sens (Keyboard Sensitivity)


Select the keyboard sensitivity. LIGHT: light MEDIUM: normal HEAVY: heavy

Vel (Keyboard Velocity)


Specify the velocity value that will be transmitted when you play the keyboard. If you want the actual keyboard velocity to be transmitted, set this to REAL. If you want a fixed velocity value to be transmitted regardless of how you play, specify the desired value.

Output (Pedal Output)


Select the sound source(s) (the internal sound source and/or external sound sources connected to MIDI OUT connector) which will be controlled by the pedals. OFF: Neither will be controlled. INT: Only the internal sound source will be controlled. MIDI: Only external sound sources will be controlled. BOTH: Both the internal sound source and external sound sources will be controlled.

Aft (Aftertouch Sensitivity)


Specify the Aftertouch sensitivity. Higher values will allow Aftertouch to be applied more easily. Normally you should leave this set to 100.

110

Chapter 3. Creating Your Own Sounds

Polarity (Pedal Polarity)


This parameter switches the polarity of the pedals. On some pedals, the electrical signal output by the pedal when it is pressed or released is the opposite of other pedals. If your pedal has an effect opposite of what you expect, set this parameter to REVERSE. If you are using a Roland pedal (that has no polarity switch), set this parameter to STANDARD.

CONTROL SOURCE
Select the type of MIDI message that will be used to control each of the following functions.

Hold (Hold Control Source)


Select the type of pedal message that will be used to hold the current parameter values. OFF: not used HOLD1: Hold 1 (controller number 64) SOST: Sostenuto (controller number 66) SOFT: Soft pedal (controller number 67) HOLD2: Hold 2 (controller number 69)

C1/C2/C3/C4 ASSIGN (C1/C2/C3/C4 Slider Assign)


These parameters set the functions controlled by the C1C4 sliders.

Assign (C1/C2/C3/C4 Slider Assign)


Select the function controlled by each slider. CC0195: Controller numbers 195 (except for 6, 3263). PITCH BEND: Pitch bend AFTERTOUCH: Aftertouch * Depending on the functions being controlled, the value may remain unchanged when the slider is moved, even if the Patch or Performance is switched.

Peak (Peak Control Source)


Select the type of pedal message that will used to hold the highest received parameter values. OFF: not used HOLD1: Hold 1 (controller number 64) SOST: Sostenuto (controller number 66) SOFT: Soft pedal (controller number 67) HOLD2: Hold 2 (controller number 69)

Output (C1/C2/C3/C4 Slider Output)


Select the sound source(s) (the internal sound source and/or external sound sources connected to MIDI OUT connector) which will be controlled by the sliders. OFF: Neither will be controlled. INT: Only the internal sound source will be controlled. MIDI: Only external sound sources will be controlled. BOTH: Both the internal sound source and external sound sources will be controlled.

Volume (Volume Control Source)


Specify whether or not Expression messages (controller number 11) will affect the volume of a Patch or Part as well as Volume messages (controller number 7). VOLUME: Only Volume messages and not Expression messages will affect the volume. VOL&EXP: Both Volume messages and Expression messages will affect the volume.

Aftertouch (Aftertouch Control Source)


Specify the type(s) of aftertouch message that will affect the internal sound source. CHANNEL: Channel pressure (the aftertouch that applies equally to all keys) POLY: Polyphonic key pressure (the aftertouch that applies independently to each key) CH&POLY: Channel pressure and Polyphonic key pressure * The XP-30s keyboard is not able to transmit Polyphonic Key Pressure messages.

SYS-CTRL ASSIGN (System Control Assign)


Control 1/2 (System Control Assign 1/2)
These settings allow you to choose two controllers for common use when controlling the parameters of a Patch or Performance. The settings in each Patch (or Performance) will determine whether the two controllers you choose here will actually be used. You will also need to specify for each Patch (or Performance) the parameters that will be controlled. CC0195: Controller numbers 195 (except for 6, 3263). PITCH BEND: Pitch bend AFTERTOUCH: Aftertouch * To use the selected controllers, you need to make System settings and Patch/Performance settings so that the MIDI messages transmitted by the selected controllers will be received. * For many control change messages, the function performed by each number is defined in the MIDI specification. These settings allow you to use control change messages without regard to their officially defined function, so please be aware of what you are doing.

111

Chapter 3

Chapter 3. Creating Your Own Sounds

s MIDI Settings (MIDI)


These parameters determine MIDI channel settings and how exclusive data is handled. * The first display of the MIDI group will be different depending on the mode you were in when you pressed [SYSTEM] (Patch mode/Performance mode/GM mode).

Tx-Ch (Patch Mode Transmit Channel)


This parameter selects the transmit channel for MIDI messages in Patch mode. If you do not want to transmit MIDI messages to external MIDI devices, turn this parameter off. If you want the transmit channel to always match the Patch Mode Receive Channel, set this parameter to Rx-Ch.

PERFORM MIDI (Performance MIDI)


Make MIDI settings for Performance mode. To make these settings, press [SYSTEM] when you are in Performance mode, and then press [MIDI] located in the row of function buttons.

Local (Local Switch)


Specify whether or not the controller section will be connected to the internal sound source (all Parts). Normally you will leave this ON, but if you wish to use the XP-30s keyboard and controllers to control only external sound sources, turn this OFF.

Control Channel (Performance Control Channel)


Select the receive channel used for selecting Performances via MIDI (Program Change and Bank Select messages). If you do not wish to use MIDI messages to select Performances, turn this OFF. If you set this to the same channel as the receive channel of a Part, Performance selection will take priority and it will not be possible to select Patches on that Part via MIDI. * The MIDI Receive Channel of each Part is set independently for each Performance.

Remote (Remote Keyboard Switch)


Turn this parameter on when you want to use an external MIDI keyboard in place of the XP-30s keyboard. In this case, the transmit channel of the external MIDI keyboard can be set to any channel. Normally you will leave this parameter off.

GM MIDI
Make MIDI settings for GM mode. To make these settings, press [SYSTEM] when you are in GM mode, and then press [MIDI] located in the row of function buttons.

Local (Local Switch)


Specify whether or not the controller section will be connected to the internal sound source (all Parts). Normally you will leave this ON, but if you wish to use the XP-30s keyboard and controllers to control only external sound sources, turn this OFF. * If you want the keyboard controller section to be disconnected only from a specific Part or Parts, use the Local parameter (PERFORM/MIDI/MIDI).

Local (Local Switch)


Specify whether or not the controller section will be connected to the internal sound source (all Parts). Normally you will leave this ON, but if you wish to use the XP-30s keyboard and controllers to control only external sound sources, turn this OFF.

Remote (Remote Keyboard Switch)


Turn this parameter on when you want to use an external MIDI keyboard in place of the XP-30s keyboard. In this case, the transmit channel of the external MIDI keyboard can be set to any channel. Normally you will leave this parameter off. * Set this parameter ON if you want performance using the Arpeggiator to be controlled by an external MIDI device. * When the Remote keyboard switch is on, all messages that arrive at MIDI IN are output from MIDI OUT.

RECEIVE MIDI
Select whether or not to receive MIDI messages to select Patches, Rhythm Sets, or Performances.

Program Change (Receive Program Change Switch)


If you want Program Change messages to be received, turn this ON. If not, turn it OFF.

Bank Select (Receive Bank Select Switch)


If you want Bank Select messages to be received, turn this ON. If not, turn it OFF.

PATCH MIDI
Make MIDI settings for Patch mode. To make these settings, press [SYSTEM] when you are in Patch mode, and then press [MIDI] located in the row of function buttons.

TRANSMIT MIDI
Specify how MIDI messages will be transmitted.

Rx-Ch (Patch Mode Receive Channel)


Select the channel on which MIDI messages will be received in Patch mode.

Program (Transmit Program Change Switch)


If you want Program Change messages to be transmitted, turn this ON. If not, turn it OFF.

Bank Sel (Transmit Bank Select Switch)


If you want Bank Select messages to be transmitted, turn this ON. If not, turn it OFF.

112

Chapter 3. Creating Your Own Sounds

Active Sensing (Transmit Active Sensing Switch)


If you want Active Sensing messages to be transmitted, turn this ON. If not, turn it OFF.

s Phrase Preview Settings (PREVIEW)


Specify how the phrase will play when you press [PHRASE PREVIEW].

SYS-EXC MIDI (Exclusive MIDI)


Specify how Exclusive messages will be transmitted and received.

PREVIEW MODE
Mode (Preview Sound Mode)
SINGLE: The notes specified by Note 14 will sound successively one by one. CHORD: The notes specified by Note 14 will sound simultaneously. PHRASE: The phrase prepared for the Patch type (category) will sound.

Device# (Exclusive Device ID Number)


When you want to transmit or receive Exclusive messages, set this parameter to match the Device ID number of the other MIDI device.

Rx.Exc (Receive Exclusive Switch)


If you want Exclusive messages to be received, turn this ON. If not, turn it OFF.

Tx.Edit (Transmit Edit Data Switch)


If you want Exclusive messages to be transmitted for each change you make while editing a Patch, Performance, or Rhythm Set, turn this ON. If not, turn it OFF.

PREVIEW KEY
Note 14 (Preview Note Set 14)
Specify the pitch (C-1G9) of the four notes that will sound when Mode (Preview Sound Mode) is set to either SINGLE or CHORD. * If PHRASE is selected for Mode, these settings will have no effect.

Rx.GM (Receive GM Exclusive Switch)


If you want GM-related Exclusive messages to be received, turn this ON. If not, turn it OFF. * For details on the GM MIDI messages, refer to Chapter 5. Using the XP-30 as the GM Sound Module (p. 124).

PREVIEW VELOCITY
Specify the velocity (0127) of the four notes that will sound when Mode (Preview Sound Mode) is set to either SINGLE or CHORD. * If PHRASE is selected for Mode, these settings will have no effect.

BANK-SEL GROUP (Bank Select Group)


Each Performance has a Bank Select Group setting (PERFORM/MIDI/TRANSMIT). The Bank Select Group parameter of each Performance specifies how Bank Select messages are transmitted when the Performance is selected. Here, you can specify the actual Bank Select Number that is transmitted for each of the BS17 selections that were made in Performance mode.

s Adjusting Tuning (TUNE)


Parameters in this group adjust the tuning of the internal sound source, or change the temperament of the keyboard. * The SCALE display of TUNE group will be different depending on the mode you were in when you pressed [SYSTEM].

Number (Bank Select Group Number)


Select the Bank select group you wish to set. The contents of each BS number are determined by the following settings for Switch, MSB and LSB.

TUNE
Master (Master Tune)
This parameter tunes the internal sound source. The displayed value indicates the pitch (frequency) of the A4 key.

Switch (Back Select Transmit Switch)


If you want the selected Bank select group to transmit its assigned Bank Select number, turn this ON. If you do not want the selected BS number to transmit a Bank Select message, turn this OFF.

Key Shift
Adjust the pitch of the internal sound source in semitone steps.

MSB (Bank Select MSB)


Specify the MSB of the Bank Select number transmitted by the selected BS number.

Scale Tune (Scale Tune Switch)


Turn this ON when you wish to play a scale other than equal temperament. You can specify one scale for Patch mode and one scale for Performance mode/GM mode. To set the tuning of each note in the scale, use the following SCALE display. * The selected scale is used even for MIDI messages received from an external MIDI device.

LSB (Bank Select LSB)


Specify the LSB of the Bank Select number transmitted by the selected BS number.

113

Chapter 3

Chapter 3. Creating Your Own Sounds

PATCH SCALE KEY SCALE


If you wish to define a scale for use in Patch mode, press [SYSTEM] while in Patch mode, and then press [TUNE] located in the row of function buttons. to access the PATCH SCALE display. If you wish to define a scale for use in Performance mode/GM mode, press [SYSTEM] while in Performance mode, and then press [TUNE] located in the row of function buttons to access the KEY SCALE display. To make settings for another Part, use the cursor buttons to select the desired Part. Define a scale by specifying how much the pitch will differ from the equal tempered pitch (in steps of 1 cent). In Patch mode there are separate screens for the white keys and black keys, and the settings for one octave (CG) will determine the tuning for all octaves. In Performance mode/GM mode, you can make settings for each key in each Part. * One cent is 1/100th of a semitone.

s Program Change (PGM CHNG)


TRANSMIT P.C (Transmit Program Change)
When you want to transmit MIDI messages (Program Change and Bank Select) to select sounds on an external MIDI device, make settings in this display and then press the ENTER button.

Channel (Transmit MIDI Channel)


Select the channel on which the MIDI message will be transmitted.

P.C# (Transmit Program Change)


Select the Program Number you wish to transmit.

Bnk-MSB (Transmit Bank Select MSB)


Select the MSB (control number 0) of the Bank Select number you wish to transmit.

Bnk-LSB (Transmit Bank Select LSB) Equal Temperament


This scale divides an octave into 12 equal parts for the tuning system that is most widely used in Western music. The XP-30 employs equal temperament when the Scale Tune Switch is set OFF. Select the LSB (control number 32) of the Bank Select number you wish to transmit.

Pure Temperament (Tonic is C)


With this tuning, the three fundamental chords sound richer compared to equal temperament. This effect only applies to one key, and transposition makes the chord ambiguous.

s Checking Things Such as the Installation Status of Wave Expansion Boards (INFO)
INFO EXP (Information Expansion Board)
The names of Wave Expansion Boards installed in slots EXPD and E are displayed. Slots without any boards installed are indicated ----------------. * If for both Expansion D: and Expansion E: an identically named Wave Expansion Board is displayed, it will be possible to select data only from the Wave Expansion Board installed in the EXPD slot. Also, the XP-30 already contains the data of the three Wave Expansion Boards listed below, and if the names of any of these Wave Expansion Boards are displayed, it will be possible to select only the onboard data (XP-AC). - SR-JV80-09 Session (XP-A) - SR-JV80-02 Orchestral (XP-B) - SR-JV80-11 Techno Collection (XP-C)

Arabian Scale
In this scale, E and B are a quarter-note lower and C#, F# and G# are quarter-note higher compared to equal temperament. The intervals between G and B, C and E, F and G#, A# and C#, and D# and F# have a natural third (the interval between a major third and a minor third). With the XP-30, you can play Arabian scale in G, C and F keys. <Examples> Note Equal Pure temperament name temperament (tonic C) C C# D Eb E F F# G G# A Bb B 0 0 0 0 0 0 0 0 0 0 0 0 0 -8 +4 +16 -14 -2 -10 +2 +14 -16 +14 -12 Arabian scale -6 +45 -2 -12 -51 -8 +43 -4 +47 0 -10 -49

BATTERY CHECK
The XP-30 contains a battery that backs up the data in internal memory. This display allows you to check the battery voltage. If the display indicates OK, there is sufficient battery voltage. If the display indicates LOW, the battery voltage has run down. Contact your nearby Roland service station to have the battery replaced.

114

Chapter 4. Memory Settings (Utility/Card Mode)


The Utility mode allows you to store Patch/Performance/ Rhythm Set settings (Write), and transmit data (Data Transfer), as well as other global XP-30 memory settings.

Basic Procedure in Utility/ Card Mode


* In order to use a memory card, you must first turn off the power, and then insert a memory card into the card slot.
fig.4-02

About Utility/Card Mode


The XP-30 goes into Utility/Card mode if you press [UTIL/ CARD]. The indicator will blink. Utility/Card mode offers nine functions categorized into two groupsUTIL 1 and UTIL 2.

UTIL 1 (Utility 1)
fig.3-20

WRITE
This function writes Patch, Performance or Rhythm Set settings youve modified into user memory (p. 116).

1. Press [UTIL/CARD] so its indicator blinks. The XP-30 will switch to Utility/Card mode.
fig.3-20

COPY
This function copies data from a Patch, Performance or Rhythm Set into the current Patch, Performance or Rhythm Set (p. 117). * The type of data that will be written, copied and initialize depends on the mode you are in when you press [UTIL/CARD]. 2. Press [ ] or [ ] to select the group (UTIL 1, UTIL 2) containing the function you want. 3. Use [ ] or [ ] to select the desired function (the function name will blink), and press [ENTER]. The display of the function youve selected will appear. * You can also access the desired function display by using the numeric keys or function buttons to specify the number of the function. * If you selected the UTIL 2 group function 1: CARD, the CARD display will appear. Here you can once again select the desired function. 4. Set parameters as necessary on each functions display. * To cancel the operation, press [EXIT].

INIT (Initialize)
This resets parameters of the current Patch, Performance or Rhythm Set to default factory settings (p. 119).

XFER (Data Transfer)


This function transmits Patch, Performance, Rhythm Set or System settings to an external MIDI device (p. 119).

PROTECT (User Memory Protect)


This function prevents user memory from being accidentally rewritten (p. 121).

UTIL 2 (Utility 2)
fig.4-01

CARD
Here you can make settings related to memory cards (p. 121).

LOAD
This function loads data from memory card into the XP-30s memory (p. 122).

5. Press [ENTER] to execute the function. When the operation is completed, the display will briefly indicate COMPLETED. 6. To return to the UTIL 1 or UTIL 2 displays, press [EXIT]. To return to the display of the previous mode, press [UTIL/CARD] to make the indicator go dark.

SAVE
This function saves data to memory card (p. 122).

FACTORY RESET
This function resets all the settings stored in the XP-30 to the factory default settings (p. 123).

115

Chapter 4

Chapter 4. Memory Settings (Utility/Card Mode)

Storing Sound Data in User Memory (WRITE)


If you turn the power off or select another Patch, Performance, or Rhythm Set after you have modified a Patch, Performance, or Rhythm Set settings, the modified data will be lost. If you wish to keep the data, store it into user memory.

The Compare Function


The Compare function allows you to play the Patch currently occupying the writing destination, so that you can check whether you really want to overwrite it. To play the Patch of the writing destination, press [UNDO/COMPARE] to access the PATCH COMPARE display. You can select the writing destination Patch in this display as well. After selecting the writing destination Patch, press [EXIT] to return to the previous display.
fig.4-05.e[

Internal Write Protect


An Internal Write Protect setting is provided to prevent the settings in user memory from being overwritten accidentally. When rewriting user memory settings, you need to turn off Internal Write Protect. If you attempt to write data when Internal Write Protect is on, the following display will appear.
fig.3-22

Writing destination Patch (group, number, name)

* Please be aware that when the Compare function is used to play a Patch, it may sound slightly different than when it is played normally.

Change the displayed ON to OFF and press [ENTER] to turn Internal Write Protect off. Press [ENTER] once again, and the data will be written into user memory. Once you turn Internal Write Protect off, it will remain off until the XP-30s power is turned off.

s Rhythm Set Write


The settings of the current Rhythm Set will be written into user memory. Press [UTIL/CARD] in Rhythm Set mode, then perform Write operation.
fig.4-06.e

s Performance Write
The settings of the current Performance will be written into user memory. Press [UTIL/CARD] in Performance mode, and perform Write operation.
fig.4-03.e

Writing destination Rhythm Set (group, number, name)

* By holding down [SHIFT] and pressing [UTIL/CARD], you can move directly to the RHYTHM WRITE display.

The Compare Function


Writing destination Performance (group, number, name)

* By holding down [SHIFT] and pressing [UTIL/CARD], you can move directly to the PERFORM WRITE display.

s Patch Write
The settings of the current Patch will be written into user memory. Press [UTIL/CARD] in Patch mode, then perform Write operation.
fig.4-04.e

The Compare function allows you to play the Rhythm Set currently occupying the writing destination, so that you can check whether you really want to overwrite it. To play the Rhythm Set of the writing destination, press [UNDO/COMPARE] to access the RHYTHM COMPARE display. You can select the writing destination Rhythm Set in this display as well. After selecting the writing destination Rhythm Set, press [EXIT] to return to the previous display.
fig.4-07.e

Writing destination Patch (group, number, name)

Writing destination Rhythm Set (group, number, name)

* By holding down [SHIFT] and pressing [UTIL/CARD], you can move directly to the PATCH WRITE display.

* Please be aware that when the Compare function is used to play a Rhythm Set, it may sound slightly different than when it is played normally.

116

Chapter 4. Memory Settings (Utility/Card Mode)

Copying Sound Source Settings (COPY)


This function lets you copy data of any Patch, Performance, or Rhythm Set into the current Patch, Performance, or Rhythm Set. Using this function effectively makes editing easier.

Performance Name Copy


The name of a Performance will be copied to the current Performance.
fig.4-11.e

Copy source Performance (group, number, name)

s Performance Copy
To copy the settings of a Performance, press [UTIL/CARD] in Performance mode, then perform Copy operation.

s Patch Copy
When you want to copy Patch settings to the current Patch, press [UTIL/CARD] in Patch mode and perform Copy operation.

Performance Part Copy


The Part settings of a Performance will be copied to the Part you specify of the current Performance.
fig.4-08.e

Patch Tone Copy


Tone settings of a Patch will be copied to the Tone you specify of the current Patch.
fig.4-12.e

Copy source Performance (group, number)

Copy source Performance name Copy destination Part

Copy source Part

Copy source Patch (group, number)

* To specify the currently selected Performance as the copy source, set Source to TEMP. * When the Copy operation is executed, an * will be displayed in front of the copy-destination part name.

Copy source Patch name Copy destination Tone Copy source Tone

* To specify the currently selected Patch as the copy source, set Source to TEMP. * When the Copy operation is executed, an * will be displayed in front of the copy-destination tone.

Performance Effects Copy


The effects settings of a Performance or Patch will be copied to the current Performance.
fig.4-09.e

Patch Effects Copy


The effects settings of a Patch or Performance will be copied to the current Patch.
fig.4-13.e

Copy source

Copy source Patch/Performance (group, number, name)

Press [ ] to move to the next display, and then select the contents of the effect that you wish to copy.
fig.4-10.e

Copy source Copy source Patch/Performance (group, number, name)

Press [ ] to move to the next display, and then select the contents of the effect that you wish to copy.
fig.4-14.e

Copy type

ALL: EFX: CHORUS: REVERB: CHO&REV:

Multi-effects, chorus, and reverb settings Multi-effects settings Chorus settings Reverb settings Chorus and reverb settings

Copy type

ALL: EFX: CHORUS: REVERB: CHO&REV:

Multi-effects, chorus, and reverb settings Multi-effects settings Chorus settings Reverb settings Chorus and reverb settings

117

Chapter 4

Chapter 4. Memory Settings (Utility/Card Mode)

The Compare Function


For the Patch Tone Copy and Patch Effect Copy operations, you can use the Compare function. The Compare function allows you to play the Patch currently occupying the copy source. To play the Patch of the copy source, press [UNDO/COMPARE] to access the PATCH COMPARE display. The copy-source Patch can be changed in this display as well, but it is not possible to select patches from XP-AE. After selecting the copy source Patch, press [EXIT] to return to the previous display.
fig.4-15.e

s Rhythm Set Copy


When you want to copy Rhythm Set settings to the current Rhythm Set, press [UTIL/CARD] in Rhythm Set mode and perform Copy operation.

Rhythm Key Copy


Individual key settings in a Rhythm Set will be copied to each key in the current Rhythm Set.
fig.4-17.e

Copy source Rhythm Set (group, number)

Copy source Rhythm Set name Copy destination Key

Copy source Key


Copy source Patch (group, number, name)

* The Compare function cannot be used with Patch Tone Copy if either TEMP or an XP-AE patch is selected as the copy source patch (Source). * The Compare function cannot be used with Patch Effect Copy if PERFORM is selected as the copy source (Source). * Please be aware that when the Compare function is used to play a Patch, it may sound slightly different than when it is played normally.

* The copy source and copy destination Key parameters can also be set by pressing a key on the keyboard. * When the Copy operation is executed, an * will be displayed in front of the copy-destination key.

The Compare Function


The Compare function can be used during the Rhythm Key Copy operation. The Compare function allows you to play the Rhythm Set currently occupying the copy source. To play the Rhythm Set of the copy source, press [UNDO/ COMPARE] to access the RHYTHM COMPARE display. The copy-source Rhythm Set can be changed in this display as well, but it is not possible to select patches from XP-AE. After selecting the copy source Rhythm Set, press [EXIT] to return to the previous display.
fig.4-18.e

Patch Name Copy


The name of a Patch will be copied to the current Patch.
fig.4-16.e

Copy source Patch (group, number, name)

Copy source Rhythm Set (group, number, name)

* If one of the XP-AE Rhythm Sets is selected as the copysource Rhythm Set (Source), the Compare function is not available. * Please be aware that when the Compare function is used to play a Rhythm Set, it may sound slightly different than when it is played normally.

Rhythm Set Name Copy


The name of a Rhythm Set will be copied to the current Rhythm Set.
fig.4-19.e

Copy source Rhythm Set (group, number, name)

118

Chapter 4. Memory Settings (Utility/Card Mode)

Initializing Sound Source Settings (INIT)


This function resets settings of the current Patch, Performance, or Rhythm Set to a standard value or to factory default settings. * Only current data will be initialized, and data resident in user memory will not be rewritten. To reset all settings to factory defaults, execute Factory Reset (UTILITY/UTIL 2/FACTORY RESET). Data can be initialized in two ways depending on the application.

s Rhythm Set Initialize


To initialize Rhythm Set settings, press [UTIL/CARD] in Rhythm Set mode and execute initialization. The Rhythm Set Initialize operation can also be used to initialize the settings of only an individual percussion instrument sound (key) that you specify. In this case, move the cursor to Key, and select the percussion instrument sound that you wish to initialize. You can specify the percussion instrument sound either from the keyboard, or by pressing TONE SELECT [1][4].
fig.4-22

Mode (Initialize Mode)


DEFAULT: Resets current data to the standard values called Initial data (INIT PATCH, INIT PERFORM or INIT SET). This mode is selected when creating sound from scratches. PRESET: Resets the current data in user memory to the factory settings. * If the current data is a Patch, Performance or Rhythm Set in preset memory (PR-APR-C, E, GM), and initialization is performed with PRESET specified, the data will be reset to the value of the correspondingly numbered user memory.

Transmitting Sound Settings (XFER)


This function lets you transmit sound source or System settings that are in the XP-30s memory or stored on memory card to an external MIDI device or User memory.

s Performance Initialize
To initialize Performance settings, press [UTIL/CARD] in Performance mode and execute initialization.
fig.4-20

s Patch Initialize
To initialize Patch settings, press [UTIL/CARD] in Patch mode and execute initialization.
fig.4-21

The process of transmitting Patch, Performance, Rhythm Set or System data to an external MIDI device is called Bulk dump. This process is used when two XP-30s with the same Patch, Performance and/or Rhythm Set settings are connected for performance or when recording Patch, Performance, Rhythm Set or System data into an external MIDI device as a backup for accidental data deletion.
fig.4-23.e

Data type Source block

Destination

While data is being transmitted, the following display will appear.


fig.4-24

* To cancel data transmission, press [EXIT]. * If you expect to successfully use settings that stipulate the use of XP-A/B/C waves and patches after theyve been sent to another unit (XP-50/60/80; or JV-1010/1080/2080), you first need to make sure that the relevant Wave Expansion Boards are installed in the other unit.

119

Chapter 4

s Transmitting Data to an External MIDI Device

Chapter 4. Memory Settings (Utility/Card Mode)

Specifies the data to be transmitted through the combinations as shown below. For example, if you wish to transmit the USER group Patches 001020, you would specify PATCH USER:001-020. Type ALL PERFORM Block USER TEMP USER TEMP CTRL PATCH RHYTHM SYSTEM *1 *2 USER TEMP USER TEMP USER 001002 001128 0132 -PATCH +PATCH *1 *2

Specifies the data to be transmitted through the combinations as shown below. For example if you wish to transmit only the PR-A group Patch 001, specify PATCH PR-A:001-001 * If the specified data will not fit completely into the transmission destination, as much of the data as will fit will be transmitted, starting at the first number of the specified transmission destination. (Example) Block Destination

PATCH PR-A:001005 User:127

If the above settings are made and transmission is executed, only the two PR-A group Patches 01 and 02 will be transmitted to USER group Patches 127 and 128. Type ALL PERFORM Block PR-A PR-B USER PR-A, B CARD PATCH USER PR-AC, GM, PR-E XP-A, B XP-C XP-D, E CARD USER PR-AC, GM, PR-E XP-A, C XP-D, E CARD SYSTEM *1 *2 Card 0132 0132 ** 001128 001128 001255 001256 001*** ** 001002 001002 001008 001*** ** ** *1

The current Performance The current Performance and the Patch or Rhythm Set assigned to each Part of the Performance

Type (Data Type)


Specify the type of data to be transmitted. ALL: Performance, Patch, and Rhythm Set PERFORM: Performance PATCH: Patch RHYTHM: Rhythm Set SYSTEM: System

*2 *1

Block (Source Block)


Specify the source of the data to be transmitted. USER: Transmit the data from user memory. TEMP: Transmit the data from the temporary area. CTRL: Transmit messages for Performance bank select, Performance program change, and Volume and Pan messages for the Parts whose Rx parameter (PERFORM/MIDI/MIDI) is turned ON.

RHYTHM

*2 *1 *1

Specified by file number Depends on the Wave Expansion Board installed

Destination
Set the transmission destination to MIDI.

Type (Data Type)


Specify the type of data to be transmitted. ALL: Performance, Patch, and Rhythm Set PERFORM: Performance PATCH: Patch RHYTHM: Rhythm Set SYSTEM: System (other than sequencer section)

s Transmitting Data to User Memory


You can transmit Patch, Performance or Rhythm Set settings to the user memory and System settings to the system memory. By loading sound data from memory card or Wave Expansion Boards to user memory, you can add many different sounds to your performance.
fig.4-27.e

Data type Source block

Destination

120

Chapter 4. Memory Settings (Utility/Card Mode)

Block (Source Block)


Specify the source of the data to be transmitted. USER: Data from user memory will be transmitted. PR-AC, E: Preset A/B/C/E data will be transmitted. GM: GM data will be transmitted. XP-AE: Data from an Wave Expansion Board will be transmitted. * XP-D, E can be selected only if the corresponding Wave Expansion Board is installed. CARD: Performance/Patch/Rhythm Set/System data stored on memory card will be transmitted.
fig.4-29.e

Memory Card-Related Settings (CARD)


XP-30 can use an optional memory card (S2M-5 (2MByte) or S4M-5 (4MByte)). Use this card when you wish to save data for which there is no more space in the internal USER group, or so that the data you created can be used on another XP-30. Memory card must be formatted before they can be used. * When you select 1: CARD in the UTIL 2 group, the following CARD display will appear. Select the function you wish to execute.
fig.4-31

File number

File name

Destination
Set the transmission destination to USER. * If the Type parameter has been set to PERFORM, PATCH, or RHYTHM, specify the first number of the transmission destination.

Before Using a Memory Card


* The power of the XP-30 must be turned off before inserting or removing a memory card. If a memory card is inserted when the power is turned on, the data in the memory card may be destroyed, or the memory card may become unusable. * Be sure to insert the memory card all the way into the slot.

This function prevents user memory from being rewritten to ensure Patch, Performance or Rhythm Set data will not accidentally be lost.
fig.4-30

* Never remove the memory card or turn off the power while an operation (formatting, or data read/write) is being performed on the memory card. Doing so will destroy the data in the memory card and/or render the memory card unusable. * If you affix the write protect label to the write protect area of the memory card, it will be impossible to format the card or write data to it. If you wish to format the card or write data to it, do so without the label affixed. For details on the write protect label, refer to the instruction included with your memory card. If you attempt to format the card or write data to it when the write protect label is affixed, the following message will appear.
fig.4-32

Internal (Internal Write Protect)


The Internal write Protect setting prevents the Write operation from rewriting user memory. When this setting is ON, the data cannot be rewritten. When this is OFF, the data can be rewritten. When the XP-30s power is turned on, this setting is always turned ON, so you will need to turn it OFF before rewriting user memory settings. It is also possible to turn this setting OFF as part of the Write procedure.

Exclusive (Exclusive Protect)


The Exclusive Protect setting prevents System Exclusive messages received from an external MIDI device from rewriting user memory settings. When this setting is ON, the data cannot be rewritten. When this is OFF, the data can be rewritten by an incoming exclusive message, even if the Internal Write Protect setting is ON.

121

Chapter 4

Preventing User Memory Writing Operation (PROTECT)

* Do not touch the contacts of the memory card, or allow them to become soiled.

Chapter 4. Memory Settings (Utility/Card Mode)

s Formatting the Memory Card for the XP-30 (FORMAT)


This function initializes (formats) a memory card so that XP30 data can be saved to it. Before a new memory card or a memory card used on another device can be used on the XP30, it must be formatted on the XP-30. * Please be aware that formatting will erase all the data already resident on the memory card.
fig.4-33

Loading a File from Memory Card into the XP-30 (LOAD)


A data file containing Patch, Performance, Rhythm Set settings and System settings will be loaded into internal memory. * Loading a new file will rewrite data currently resident in memory. To keep existing data, save it to memory card before loading new data.
fig.4-38

s Renaming a File (RENAME)


This function changes the name of a file on the memory card. * A file name of up to eight characters can be assigned. For details on assigning a name, refer to Assigning a Name (p. 46). * File name extensions cannot be changed.
fig.4-34.e

* If you wish to load only a portion of data from the file, refer to Transmitting Data to User Memory (p. 120).

Saving Data to Memory Card (SAVE)


The Patch, Performance, Rhythm Set, and System settings in internal memory will be saved as a single file to memory card, with the name you specify. To overwrite a previously existing file on the memory card, select the file number of that file.
fig.4-39

Original file name

New file name

s Deleting Unwanted Files (DELETE)


Use this function to delete unwanted files from memory card.
fig.4-35

* Data files contain an entire set of parameter settings for the sound source. It is not possible to save individual Patches or Performances to memory card. * A file name of up to eight characters can be assigned. For details on assigning a name, refer to Assigning a Name (p. 46).

s Checking the Contents Memory Card (INFO)


This function displays the number of files on the memory card, the free area of the disk, and the size of each file.
fig.4-36.e

The number of files that can be saved will depend on the memory card you use. S2M-5 (2MB type): approximately 29 files S4M-5 (4MB type): approximately 59 files

File number

File name

File size

Number of files on memory card

Free area

122

Chapter 4. Memory Settings (Utility/Card Mode)

Recalling Factory Default Settings (FACTORY RESET)


This operation will restore all the data in the XP-30 to the factory settings. * If the XP-30 internal memory already contains important data that you have created, this operation will cause all of this data to be lost. If you wish to keep the data, you must save it on an optional memory card (p. 122) or on an external MIDI sequencer (p. 119).
fig.4-40

* If Internal Write Protect is turned ON, the following display will appear, and the Factory Reset operation will not be executed.
fig.3-22

Change the displayed ON to OFF and press [ENTER] to turn Internal Write Protect off. Are You Sure? will be displayed, press [ENTER].

123

Chapter 4

Chapter 5. Using the XP-30 as the GM Sound Module


The XP-30 features a GM modea convenient way to play back or create GM score data (music files for GM sound module). Youre able to play back commercial GM score data releases and even modify various parameter settings for enhanced musical expression.

GM System On Message
The GM System On message puts the unit in a state that conforms to the GM System and initializes a GMcompatible sound module. * If the Rx GM parameter (SYSTEM/MIDI/SYS-EXC MIDI) is set OFF, GM System On messages cannot be received.

Entering GM Mode
Use GM mode to place the XP-30s sound source in GM System compatible mode. Basically GM mode is similar to a special kind of Performance in which a GM System Rhythm Set is assigned to Part 10, and GM System Patches are assigned to other Parts. But however, you cant store GM mode settings in user memory.
fig.5-01.e

s Playing Back a GM Score


When the XP-30 is in GM mode, it plays back GM scores correctly. But beyond this, the XP-30 provides many extended features not defined in GM System specifications, and if you create music files using these extended features, your song may not play back correctly on other GMcompatible sound modules. * The XP-30 is not compatible with the GS format (standard format for multitimbral sound sources advocated by Roland). Music files bearing the GS logo (GS music data) may therefore not play back correctly on the XP-30. * The beginning of a GM score normally contains a GM System On message. So if you play back a GM score starting in the top of a song, XP-30 will switch itself to GM mode. But if you play back a GM score starting in the middle of a song, XP-30 may not switch itself to GM mode, and the GM score may not play back correctly. So to be safe, its recommended to manually set the XP-30 to GM mode before playing back a GM score.

GM Patch/Rhythm Set (number, group)

Part number

The GM PLAY display shows a Patch or Rhythm Set assigned to each Part. Each time you enter GM mode, the GM Drum Set is assigned to Part 10, and Piano 1 is assigned to other Parts. You can also select other GM Patches and GM Drum Sets for each Part to match the performance. 1. Hold down [SHIFT] and press [PERFORM] to call up the GM PLAY display. When you switch the XP-30 into GM mode, the sound source initializes itself for basic GM System settings. 2. To change the current Part, press [ ] or [ ].

3. To change the GM Patch or GM Rhythm Set assigned to the Part, perform the same procedure as you do when you select a Patch or Rhythm Set.

Muting a Specific Part


When you switch over to GM mode, all Parts will be set to receive MIDI messages. To turn off a specific Part so that it will not sound, set the Recieve Switch to OFF for the Part. 1. Make sure that [EDIT] indicator is dark. If it is lit, press [EDIT] to turn it off. At this time, the function button indicators will indicate the on/off status of each Part. When [1-8/9-16] indicator is dark, the function button indicators will indicate the status of Parts 1-8. When [1-8/9-16] indicator is lit, the function button indicators will indicate the status of Parts 9-16. Lit is on, and dark is off. 2. Press the function button to switch Parts on/off.

s Initializing the Sound Source for GM System Basic Settings


To play back a GM score correctly, the sound source must first be initialized to basic GM system settings. The XP-30s sound source is initialized in the following situations: - When the XP-30 is switched to GM mode - When it receives a GM System On message from an external MIDI device - When a GM System On message is encountered in the song data being played back At power on - When you execute the GM Initialize function (p. 128). * Because effects settings are not defined in the GM System, they will not initialize to factory settings unless the GM Initialize (DEFAULT) or Factory Reset is executed.

124

Chapter 5. Using the XP-30 as the GM Sound Module

Modifying GM Mode Settings


GM mode also offers parameters that you can modify for each Part. You can modify settings like effects, pan and level to customize a GM score playback to your preference. * When GM mode is initialized (p. 128), all these settings will be lost. 1. Hold down [SHIFT] and press [PERFORM] to call up the GM PLAY display. 2. Press [EDIT] to make the indicator light. 3. Use the function buttons to select a display group. The button indicator of the selected display group will blink.
fig.5-02

s Making Effects Settings in GM Mode (EFFECTS)


Parameter configurations of GM effects and Performance effects are almost the same. For details refer to Setting Effects for a Performance (EFFECTS) (p. 84). Make settings for the Multi-Effects/Chorus/Reverb effects used in GM mode. * If an x mark is displayed at the right of the display name, the effect for that display has been turned off. Turn the corresponding effect on before you make settings (p. 62).

OUTPUT
Make settings to specify how each Part will be output.

Output Assign (Output Assign/Output Level)


When the Output Assign parameter is set to MIX, the output of each Part will be sent to the OUTPUT jacks without passing through Multi-Effects. If this parameter is set to EFX, the output will be passed through Multi-Effects. If PATCH is selected, the output assign settings of the GM Patch assigned to the Part will be used. The Output Level parameter adjusts the volume of each Part.

* In GM mode, you can press the function buttons [2/ 10(EFFECTS)], [4/12(PART)], and [8/16(INFO)]. 4. Use [ ] or [ ] to select a display page. 5. If you have selected a parameter display that can be set independently for each Part, the number of the Part selected for editing will be shown in the display. To select a different Part, press [EDIT] to temporarily turn off the indicator, and use [1-8/9-16] and the function buttons to select a Part. 6. Use [ ] or [ ] to move the cursor to the parameter

Chorus (Chorus Send Level)


Adjust the amount of chorus for each Part.

Reverb (Reverb Send Level)


Adjust the amount of reverb for each Part.

GM EFX TYPE (EFX Type)


Specify the type of Multi-Effects that will be used in GM mode.

you wish to modify. 7. Use the VALUE dial, [INC]/[DEC] or numeric keys and modify the parameter value. * If youve made a mistake in setting the parameter value or you dont like the changes, just press [UNDO/COMPARE] to restore the value to what it was. 8. If you wish to move to another display group, press [EDIT] to make the indicator light, and use the function buttons. * You can also move to another display group by holding down [SHIFT] and using [ ] or [ ]. Since this can be done even when [EDIT] indicator is dark, it is a faster way to get around because you dont have to turn on [EDIT] indicator each time. 9. Repeat steps 38 to complete a GM mode settings. 10. When you finish making settings, press [EXIT] to return to the GM PLAY display. * You can also use the Palette display in the same manner when you edit in Performance mode (p. 65).

Type (EFX Type)


Select the type of Multi-Effects. For details refer to MultiEffects Types (EFX Parameter) (p. 93).

GM EFX PRM (GM EFX Parameters)


Make parameter settings for the EFX type selected by the Type parameter. For details refer to Multi-Effects Types (EFX Parameter) (p. 93).

GM EFX OUT (GM EFX Output)


Specify the output routing for Parts whose Output Assign is set to EFX. * The settings in this display have no effect on Parts whose Output Assign is set to MIX.

Mix Out (EFX Output Level)


Adjust the volume balance of the direct sound and the MultiEffects sound.

Chorus (Chorus Send Level)


Adjust the amount of chorus applied to the sound that passed through Multi-Effects.

125

Chapter 5

Chapter 5. Using the XP-30 as the GM Sound Module

Reverb (Reverb Send Level)


Adjust the amount of reverb applied to the sound that passed through Multi-Effects.

GM REVERB
Make GM mode reverb settings. * In GM mode, the reverb effect settings for the GM Patch assigned to each Part will be ignored (except for the Send Level parameter).

GM CHORUS
Make settings for the chorus effect used in GM mode. * In GM mode, the chorus effect settings for the GM Patch assigned to each Part will be ignored (except for the Send Level parameter).

Type (Reverb/Delay Type)


Select the type of Reverb effect. ROOM1: dense reverb with short decay ROOM2: sparse reverb with short decay STAGE1: reverb with greater late reverberation STAGE2: reverb with strong early reflections HALL1: reverb with clear reverberance HALL2: reverb with rich reverberance DELAY: a conventional delay PAN-DLY: a delay with echoes that move left and right

Rate (Chorus Rate)


Adjust the speed of modulation for the chorus sound.

Depth (Chorus Depth)


Adjust the depth of modulation for the chorus sound.

Delay (Chorus Pre Delay)


Adjust the time delay from the original sound until when the chorus sound is heard. Higher settings will create a more spacious sound.

Time (Reverb/Delay Time)


Adjust the time of reverberation. If the Type parameter is set to DELAY or PAN-DLY, this parameter will adjust the time delay from the original sound until when the first echo will sound.

Fbk (Chorus Feedback Level)


Adjust the amount of sound from the chorus that is returned (fed back) to the input of the chorus. Higher settings will result in a more intense effect.

Level (Chorus Level)


Adjust the volume of the chorus sound.

Fbk (Delay Feedback Level)


Adjust the amount of delayed sound that is returned (fed back) to the delay. Higher values result in more delay repeats. * If you have selected any one of the Reverb types (ROOM1 HALL2), this parameter has no effect.

Out (Chorus Output Assign)


Select the way in which the Chorus and Reverb are connected. MIX:
fig.3-27.e

The Chorus sound and the Reverb sound are mixed.

HF Damp (Reverb/Delay HF Damp)


Reverb OUTPUT

Chorus input

Reverb input

Chorus

Adjust the frequency above which the reverberant sound will be cut. As the frequency is set lower, more of the high frequencies will be cut, resulting in a softer and more muted reverberance. If you do not want the high frequencies to be cut, set this parameter to BYPASS.

REV: Apply reverb to the chorus sound.


fig.3-28.e

Level (Reverb/Delay Level)


Adjust the volume of the reverberant (or delayed) sound.

Chorus input Chorus Reverb input Reverb OUTPUT

About Effects for GM-Compatible Sound Modules


Most GM-compatible sound sources provide effects such as reverb and chorus, but the use of effects is not included in the GM System Level 1 guidelines. This means that song data created for the XP-30s GM mode that uses Multi-Effects/Reverb/Chorus may not playback correctly on other GM-compatible sound sources.

M+R: Mix the chorus sound to which reverb is not applied and the chorus sound to which reverb is applied.
fig.3-29.e

Reverb input

Chorus

Reverb

OUTPUT

Chorus input

126

Chapter 5. Using the XP-30 as the GM Sound Module

s Setting a Part (PART)


PATCH
Select the GM Patch assigned to each Part.

Convenient Functions in GM Mode (GM Utility)


In the GM mode, you can copy effects settings, initialize GM mode, and transmit GM mode settings, using the Utility functions.

Number (GM Patch Number)


Select the number (001128) of the GM Patch. * In GM mode it is not possible to select USER or PRESET A/B/ C/E Patches.

Basic Procedure
1. In the GM mode, press [UTIL/CARD] so its indicator blinks. The XP-30 will switch to Utility/Card mode. 2. Press [ ] or [ ] to select the UTIL 1 group.
fig.5-03

SETTING
Make settings for the volume, pan, and pitch of each Part.

Volume
Adjust the volume of each Part.

Pan
Adjust the stereo position of each Part. L64 is full left, 0 is center, and 63R is full right. * If you modify the settings of the Volume parameter or Pan parameter, they will be reflected in the following INFO group displays. * The functions of the UTIL 2 group can also be executed from GM mode. The operation is the same as in other modes. 3. Press [ ] or [ ] to select the desired function (the function name will blink), and press [ENTER]. The display of the function youve selected will appear. * You can also access the desired function display by using the numeric keys or function buttons to specify the number of the function. 4. Set parameters as necessary on each functions display. * To cancel the operation, press [EXIT]. 5. Press [ENTER] to execute the function. When the operation is completed, the display will briefly indicate COMPLETED. 6. To return to the UTIL 1 display, press [EXIT]. To return to the GM PLAY display, press [UTIL/CARD] to make the indicator go dark.

Coarse (Coarse Tune)


Adjust the pitch of each Part in semitone steps (-4+4 octaves).

Fine (Fine Tune)


Make fine adjustments in 1-cent steps to the pitch specified in Coarse Tune. (-50+50 cents) * 1 cent is 1/100th of a semitone.

s Confirming MIDI Information of Each Part (INFO)


In this display you can check the receive status of various types of MIDI message for each Part. This is a convenient way to check that the sound source is responding correctly to messages from the keyboard or external MIDI controllers. For items other than Voice, you may modify the values. When you do so, a MIDI message will be transmitted, and can be recorded on the sequencer, etc.

Mod (Modulation Information) Breath (Breath Information) Foot (Foot Information) Vol (Volume Information) Pan (Pan Information) Exp (Expression Information) Hold (Hold 1 Information) Bend (Pitch Bend Information) Aftertouch (Aftertouch Information) Voices (Voice Information)
The number of voices used.

127

Chapter 5

Chapter 5. Using the XP-30 as the GM Sound Module

s Copying Effects Settings (COPY)


This function copies effects settings from a Patch or Performance to the GM mode.
fig.5-04.e

s Transmitting GM Mode Settings (XFER)


fig.5-07

Copy source

Copy source Patch/Performance (group, number, name)

Press [ ] to move to the next display, and then select the contents of the effect that you wish to copy.
fig.5-05.e

Copy type

ALL: EFX: CHORUS: REVERB: CHO&REV:

Multi-effects, chorus, and reverb settings Multi-effects settings Chorus settings Reverb settings Chorus and reverb settings

It is not possible to store GM mode settings in user memory. If you wish to keep your GM mode settings, you can transmit them as a MIDI message to an external MIDI device. Prepare the external MIDI device to record data, and press [ENTER]. The following GM mode settings for each Part are transmitted. - Program number of the GM Patch - Volume (control number 7) - Pan (control number 10) - Reverb send level (control number 91) - Chorus send level (control number 93) - Pitch bend sensitivity - Fine tune - Coarse tune * If you do not want the settings of a specific Part to be transmitted, turn off the Recieve Switch for that Part (p. 124).

s Initializing GM Mode (INIT)


fig.5-06

* As GM Initialize initializes only GM mode data, data stored in user memory will not be initialized. To initialize all settings to factory settings, use Factory Reset (UTILITY/UTIL 2/ FACTORY RESET) (p. 27). There are two initialize methods. GM-ON: Initializes GM mode settings using a GM System On message. DEFAULT: Initializes all GM mode settings including effects settings to factory settings.

128

Chapter 6. Getting the Full Potential of the XP-30


This section discusses various techniques for effectively using the XP-30 for specific applications. The more you use the XP-30, the faster youll appreciate the real power of this unit.

s Holding a Note with Modulation Retained


In general, pressing the Hold pedal makes a note continue to sound. However, other effects will go off. To keep other effects effective as well, perform the following procedure. 1. Connect an optional pedal switch to the HOLD PEDAL jack. 2. Select a Patch (PR-C:110 Crash Pad, etc.) to which an effect will be applied when the modulation lever is moved on the PATCH PLAY display. 3. Set the Hold parameter (SYSTEM/CONTROL/ CONTROL SOURCE) to HOLD1. 4. Call up the PEAK & HOLD display (PATCH/ CONTROL) and set Ctrl 1 parameter to HOLD. 5. Press a note and press the pedal switch as you move the modulation lever forward. 6. When the note and modulation lever are released, both the note and the effect produced by the modulation lever will be held.

Techniques for Using Patches


s Reinforcing Filter Characteristics
If you want to reinforce filter characteristics, set the Type parameter (PATCH/COMMON/STRUCT) to 2, and seriesconnect the TVFs of Tones 1 and 2. This example shows how to boost the effectiveness of the filter for PR-C:014 MKS-80 Brass. 1. Select PR-C:014 MKS-80 Brass on the Play display (PATCH). 2. Press [FILTER/ENV] to light the indicator. 3. Move the CUTOFF and RESO. sliders while you play notes and hear how sound changes. 4. Set the Type parameter (PATCH/COMMON/STRUCT) to 2. 5. Again, move the CUTOFF and RESO. sliders and hear how the sound changes. Notice the effectiveness of the filter has changed. * If the result is difficult to hear, press [EFFECTS ON/OFF] to turn off each effect unit (Multi-Effects, Chorus, Reverb) (p. 62).

s Syncing the LFO Cycle to System Tempo


1. Select PR-B:052 Blade Racer on the PATCH PLAY display. 2. Set the Source parameter (PATCH/COMMON/PATCH CLOCK) to SYSTEM. 3. Make sure that each Tones EXTSync parameter (PATCH/LFO/LFO 1, 2) is set to CLOCK. If not, reset. 4. Set the Clock Source parameter (SYSTEM/SETUP/ SYSTEM SETUP) to INT. * When the Clock Source parameter is set to MIDI, you can achieve synchronization with the tempo of an external MIDI device. 5. Try playing the keyboard while you change the System Tempo parameter (SYSTEM/SETUP/SYSTEM SETUP) to various values. 6. Set the modulation depth as desired using LFO DEPTH1:2 display (PATCH/LFO) of each Tone. * When you have selected PR-B:047, 049, 051056, 069, PRC:034, 093, 097, 099, or 123, it is also possible to synchronize the LFO to the systems tempo clock by setting the Source parameter (PATCH/COMMON/PATCH CLOCK) to SYSTEM. Try it.

s Making the Up-Beat Note Sound at the Same Time You Play a Down-Beat Note
1. Select PR-A:087 Music Bells on the PATCH PLAY display and listen to the sound. 2. Call up the TONE DELAY display (PATCH/WAVE). 3. Select Tone 1. 4. Set Tone 1s Mode parameter to PLAYMATE and the Time parameter to 32. 5. Play the XP-30s keyboard keeping a constant tempo. Tones 1 and 2 sound alternately. Tone 1 will sound at the timing point exactly between a note you press and the following note. Try various settings, for instance use different wave or modify the pitch. * Tone 1 will not sound if the two keys are pressed at an interval of 2 seconds or longer.

129

Chapter 6

Chapter 6. Getting the Full Potential of the XP-30

s Modifying Multi-Effects to Match the Systems Tempo


1. Select PR-C:094 Albion on the PATCH PLAY display. 2. Set the Source parameter (PATCH/COMMON/PATCH CLOCK) to SYSTEM. 3. Make sure that the Type parameter (PATCH/EFFECTS/ PATCH EFX TYPE) is set to STEP-FLANGER. If not, reset. 4. Make sure that the Step Rate parameter (PATCH/ EFFECTS/PATCH EFX PRM) is set as a note value. If not, reset using a note value. 5. Set the Clock Source parameter (SYSTEM/SETUP/ SYSTEM SETUP) to INT. 6. Try playing the keyboard while you change the System Tempo parameter (SYSTEM/SETUP/SYSTEM SETUP) to various values. Youll notice that the tempo of the Patchs modulation changes in accordance to the tempo clock of the XP-30s system. You can modify EFX parameter values in accordance to the systems tempo clock, when you have selected the following types for the EFX Type parameter. Type 16: STEP-FLANGER 19: TRIPLE-TAP-DELAY 20: QUADRUPLE-TAP-DELAY EFX Parameter Step Rate parameter Delay LR parameter Delay 14 parameter

s Playing Phrase Loops at a Systems Tempo


The internal wave expansion XP-C group contains Patches derived from waveforms with tempo (BPM) indication (phrase loops). You can play these phrase loops in sync with the systems tempo. 1. Select XP-C:001 Teknoperator on the PATCH PLAY display. 2. Set the Source parameter (PATCH/COMMON/PATCH CLOCK) to SYSTEM. 3. Call up the WAVE display (PATCH/WAVE). 4. Change the Tone by pressing TONE SELECT [1][4] and look for the Tone that uses waveforms with BPM indication. The wave name will appear in parentheses ( ) below the Number parameter. Youll notice that for this example, Patch Tone 1 uses a phrase loop called 132:Detroit. 5. Call up the TONE DELAY display (PATCH/WAVE). 6. Set the Tone 1s Mode parameter to TEMPO-SYNC. 7. Set the Clock Source parameter (SYSTEM/SETUP/ SYSTEM SETUP) to INT. 8. Try playing the keyboard while you change the System Tempo parameter (SYSTEM/SETUP/SYSTEM SETUP) to various values. The phrase loop speed will change in accordance to the systems tempo clock. * The phrase loop will sound with the systems tempo regardless of which key you press. The settings for pitch and FXM will be ignored.

* When you have selected PR-B:057, 065, 068, PR-C:094, 096, and 098, it is also possible to sync the EFX parameter variations of the sequencers tempo clock by setting the Source parameter (PATCH/ COMMON/PATCH CLOCK) to SYSTEM. Try it and see.

s Using a Pedal Switch to Modify the Rotary Speed of the Rotary Effect
1. Call up the CONTROL PEDAL display (SYSTEM/ CONTROL) and set the Assign parameter to CC04:FOOT-TYPE. 2. Select PR-A:054 Rocker Spin on the PATCH PLAY display. This Patch uses ROTARY as the EFX type. 3. Call up the PATCH EFX CTRL display (PATCH/ EFFECTS), then set the Speed parameter to FOOT:+63. 4. Connect an optional pedal switch to the CONTROL PEDAL jack. 5. When you wish to speed up the rotary effect, press the pedal switch. Releasing the pedal switch will slow down the rotary effect.

130

Chapter 6. Getting the Full Potential of the XP-30

s Using the Slider to Pan Sounds in Real Time


You can assign various functions to the C1 slider. In this example, the stereo location (pan position) of a Patch will change by moving the C1 sliders up or down. 1. Call up the C1 ASSIGN display (SYSTEM/CONTROL). 2. Set the Assign parameter to CC10:PANPOT. * With other Assign parameter settings, you can try different variations. 3. Select a Patch on the PATCH PLAY display. 4. Press [CONTROLLER] to light the indicator. 5. Move the C1 slider while you play the keyboard. Youll notice that sound will pan right and left. * If the stereo location of the sound is difficult to hear, press [EFFECTS ON/OFF] to turn off each effect unit (Multi-Effects, Chorus, Reverb) (p. 62).

6. Call up the PATCH display (PERFORM/PART) and set the Number parameter to the same number as the Program number of the sound you wish to play from the external MIDI device. * If the Program number of the external MIDI device reads 0127, set the P.C Number parameter by adding 1 to the external MIDI devices value. 7. Save the Performance. 8. Try changing from another Performance to the Performance just saved, and see if the sound of the external MIDI device changes to what you want. If not, check your settings and the external MIDI device.

s Changing Sounds with a Pedal Switch


You can change Patch/Performance/Rhythm Set in succession using a pedal switch. 1. Connect a pedal switch to a CONTROL PEDAL jack. 2. Call up the CONTROL PEDAL display (SYSTEM/ CONTROL) and set the Assign parameter to 98:PROGUP. 3. Call up the PLAY display of a sound source. 4. Each time you press the pedal, you call up the next Patch, Performance or Rhythm Set.

Using the XP-30 to Play Live


s Changing Multiple Sounds of an External MIDI Device Simultaneously
When a different Performance is selected, the sound corresponding to the Bank Select number and Program number of the selected Performance will usually be chosen on the external MIDI device. Once you have set the Bank Select number and Program number for each Part to match the desired sound of the external MIDI device, you can select several sounds on the external MIDI device by changing the Performance. 1. Select the Part to be used to control the external MIDI device. 2. Call up the BANK-SEL GROUP display (SYSTEM/ MIDI). 3. Set the Number parameter to select the appropriate bank select group to match the bank select of your external MIDI device, turn the Switch parameter ON for that group, and set the LSB and MSB parameters. 4. After switching to the MIDI display (PERFORM/MIDI) for the part that will control the external MIDI device, set the Channel parameter to match the receive channel of the external MIDI device, and turn the Tx parameter ON. 5. Select the TRANSMIT (PERFORM/MIDI) display, and set the Bank Select Group parameter to the bank select group that you selected in step 3.

131

Chapter 6

Chapter 6. Getting the Full Potential of the XP-30

Using External MIDI Devices


s Using the XP-30 to Control External MIDI Devices
1. Use a MIDI cable to connect the MIDI OUT connector of the XP-30 to the MIDI IN connector of the external MIDI device.
fig.6-01.e

* If you daisy-chain three or more MIDI devices using IN THRU IN THRU ..., the MIDI signal may become garbled, and data errors may occur. In such cases, use a MIDI Thru Box. MIDI Thru Boxes are devices that allow a single stream of MIDI data to be sent to a large number of MIDI devices without causing data errors.

MIDI OUT

s Playing the XP-30s Sound Source from an External MIDI Device


1. Use a MIDI cable to connect the external MIDI devices MIDI OUT connector to the XP-30s MIDI IN connector.
fig.6-03.e

XP-30

MIDI IN

MIDI IN

MIDI Keyboard

2. Set the XP-30s transmit channel to match the external MIDI devices receive channel. The transmit channel is determined by the following parameters. - Patch mode Tx-Ch parameter (SYSTEM/MIDI/PATCH MIDI) - Performance mode Channel parameter (PERFORM/MIDI/MIDI) Turn the Tx parameter (PERFORM/MIDI/MIDI) to ON. 3. If you want to play only the sound source of the external MIDI device, set the Local parameter (SYSTEM/MIDI/ PATCH MIDI) / (SYSTEM/MIDI/PERFORM MIDI) to OFF. If you wish to connect two or more external MIDI devices, use the MIDI THRU connector of the external MIDI device.
fig.6-02.e

XP-30

MIDI OUT

MIDI Keyboard

2. Set the XP-30s receive channel to match the external MIDI devices transmit channel. The receive channel is determined by the following parameters. - Patch mode Rx-Ch parameter (SYSTEM/MIDI/PATCH MIDI) - Performance mode Channel parameter (PERFORM/MIDI/MIDI) Turn the Rx parameter (PERFORM/MIDI/MIDI) to ON.

MIDI OUT

s Selecting XP-30 Sounds from an External MIDI Device


By transmitting Bank Select messages (controller number 0 and 32) and Program Change messages from the external MIDI device to the XP-30, you can select Patches, Performances, or Rhythm Sets. In other words, when you select sounds on an external MIDI keyboard, the corresponding MIDI message will be transmitted to the XP30, causing the XP-30 to select the appropriate Patch, etc. * If the XP-30 receives only Program Change messages without receiving Bank Select messages, it will select sounds only from the currently selected group such as PR-A or USER.

XP-30

MIDI IN

MIDI THRU

MIDI Keyboard MIDI IN

MIDI Keyboard

132

Chapter 6. Getting the Full Potential of the XP-30

Selecting Patches
The MIDI messages transmitted by the external MIDI device will be received by the XP-30 to select Patches as shown in the following table.
Group USER PR-A PR-B PR-C PR-D (GM) PR-E XP-A XP-A XP-B XP-B XP-C XP-C XP-D XP-D XP-E XP-E Number 1128 1128 1128 1128 1128 1128 1128 129255 1128 129255 1128 129256 1128 129256 1128 129256 Bank Select MSB LSB 80 81 81 81 81 81 84 84 84 84 84 84 84 84 84 84 0 0 1 2 3 4 0 1 2 3 4 5 6 7 8 9 Program Number 1128 1128 1128 1128 1128 1128 1128 1127 1128 1127 1128 1128 1128 1128 1128 1128

Selecting Rhythm Sets


The MIDI messages transmitted by the external MIDI device will be received by the XP-30 to select Rhythm Sets as shown in the following table.
Group USER PR-A PR-B PR-C PR-D (GM) PR-E XP-A XP-C XP-D XP-D XP-E XP-E Number 1, 2 1, 2 1, 2 1, 2 1, 2 1, 2 18 18 1128 129256 1128 129256 Bank Select MSB LSB 80 81 81 81 81 81 84 84 84 84 84 84 0 0 1 2 3 4 0 4 6 7 8 9 Program Number 1, 2 1, 2 1, 2 1, 2 1, 2 1, 2 18 18 1128 1128 1128 1128

<Example> Selecting PR-B Patch number 10 from an external MIDI device Transmit data to the XP-30 in the following order. (Values are in decimal.) Controller number 0 (Bank Select MSB button), value 81 Controller number 32 (Bank Select LSB button), value 1 Program number 10

In order to select Rhythm Sets, the MIDI channel of the transmitting device must match the receive channel of Part 10 of the Performance. When the XP-30 is shipped, Part 10 is set to MIDI channel 10.

Selecting Performances
The MIDI messages transmitted by the external MIDI device will be received by the XP-30 to select Performances as shown in the following table.
Group USER PR-A PR-B Number 132 132 132

80 81 81

0 0 1

132 132 132

In order to select a Performance, the MIDI channel of the transmitting device must match the XP-30s Control Channel parameter (SYSTEM/MIDI/PERFORM MIDI). In order to select the Patch or Rhythm Set of a Part, the transmit channel must match the receive channel of the Part. However if the Control Channel parameter and the receive channel of a Part have the same setting, the Control Channel parameter setting will take priority so that messages received on this channel will select Performances.

133

Chapter 6

Bank Select MSB LSB

Program Number

Chapter 6. Getting the Full Potential of the XP-30

Enjoying Desktop Music


The XP-30 can be controlled by music software running on a computer. This will allow you to create your own songs, and also to select sounds or edit sounds from the computer display. The features available to you when using a computer will vary greatly, depending on the software you use, so it is important that you choose software suited to your needs.

* This setting determines the transmission speed (baud rate) between your computer and the MIDI sound module (the XP30), and the setting used by the computer must match the setting on the XP-30. Here we explained how to make the setting on the XP-30. To make settings on your computer, you will need to make settings for your software. If you are using Windows, settings may be different than the above, depending on your driver settings. If so, carefully read the owners manual that was included with your driver. * The PC-1 baud rate is 31.25 (kbit/sec), and the PC-2 baud rate is 38.4 (kbit/sec). In step 3, the connections will be slightly different depending on the type of computer you are using, so read the section (3a, 3b) that applies to you. 3a. If youre using a PC, connect the computer cable to the serial port (RS-232C) connector on the rear of the computer. Computer cable: RSC-15AT (sold separately) This is a 9 pin cable. If you need a 25 pin cable, refer to Computer Cable Wiring Diagrams (p. 208) and purchase an appropriate cable. 3b. If youre using an Apple Macintosh computer, connect the computer cable to the modem port or printer port on the rear of the computer. Computer cable: RSC-15APL (sold separately)

s Connecting to Your Computer


Two Connection Methods
There are two ways to connect the XP-30 to your computer: by means of the Computer connector, or by using the MIDI connectors. To make connections via the Computer connector, use a Computer cable to connect the serial port (RS-232C connector) of your computer to the Computer connector of the XP-30. To make connections via MIDI, you will need a MIDI interface (such as the Roland Super MPU64, etc.). Use MIDI cables to connect the XP-30s MIDI connectors to the MIDI connectors of the MIDI interface, after it has been connected to your computer. Connect the XP-30 to your computer using the method that is appropriate for your setup. If you are making connections using MIDI, read from p. (p. 135).

Connecting with Computer Connector


1. Turn off the XP-30, your computer and all peripheral devices. * To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. 2. Set the COMPUTER switch on the rear panel of the XP-30 as the following figure. In general, set the switch to PC-2 for PC, and to Mac for Apple Macintosh series.
fig.6-04.e

Apple Macintosh

PC

* Before changing the setting of the Computer switch, you must first turn off the power on the XP-30.

134

Chapter 6. Getting the Full Potential of the XP-30

4. Connect the other end of the Computer cable to the COMPUTER connector on the left side of the XP-30.
fig.6-05.e

Apple Macintosh

Modem Port or Printer Port

XP-30 Rear Panel PC Optional computer cable RSC-15APL

Serial Port (|O|O|)

Optional computer cable RSC-15AT

* In order to hear the sounds of the XP-30, you will also need to connect an AC cord, and audio cables or headphones. If you have not yet made connections, please read Making Connections (p. 24). If you are finished making connections, read from the Turning On the Power (p. 26).

Connecting with MIDI Connectors


If a MIDI interface (Roland Super MPU64, etc.) is connected to your computer, or if a MIDI interface adaptor is connected, you can use the MIDI connectors to make connections. * For details on how to install the MIDI interface, refer to the owners manual for your MIDI interface. 1. Turn off the XP-30, your computer and all peripheral devices. * To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. 2. Set the COMPUTER switch on the rear panel of the XP-30 to MIDI.
fig.6-06

* Before changing the setting of the Computer switch, you must first turn off the power on the XP-30.

135

Chapter 6

Chapter 6. Getting the Full Potential of the XP-30

3. Use a MIDI cable (sold separately) to connect the MIDI OUT connector of the MIDI interface to the MIDI IN connector of the XP-30. 4. Use a MIDI cable to connect the MIDI IN connector on the MIDI interface to the MIDI OUT connector on the XP-30. * This connection is necessary in order to use the controller section (keyboard section) of the XP-30.
fig.6-07.e

Apple Macintosh

XP-30 Rear Panel

MI
IN

DI

Modem or Printer Port

OU T

MIDI Interface Adapter

The setting is MIDI

PC

Super MPU64

XP-30 Rear Panel

USB Connector The setting is MIDI


USB Cable

136

Chapter 6. Getting the Full Potential of the XP-30

s Disconnecting the Keyboard from the Internal Sound Source (Local OFF)
The XP-30 contains a controller section (keyboard section) and sound generating section, packaged as a single unit. This means that you can make a setting (Local Control) that specifies whether or not the performance data from the keyboard will be transmitted directly to the sound source. When you use the XP-30 by itself, you will normally set it to Local ON. However, when you are using it as a sound generator for a DTM (desktop music) system, you should set the Local parameter (SYSTEM/MIDI/PERFORM MIDI) to OFF so that the keyboard will be disconnected from the internal sound generator.
fig.6-08.e

Turn on the Thru Function of Your Sequencer Software


In order for the musical data received by the computer from the XP-30 to be transmitted back to the XP-30, the Thru function of the sequencing program must be turned on. When the Thru function of the sequencing program is turned on, MIDI messages received at MIDI IN will be retransmitted without change from MIDI OUT. For details on whether or not your sequencing program has a Thru function, and how to set the Thru function, refer to the owners manual for your sequencing program. * If your sequencing program does not have a Thru function, set the XP-30s Local Control to ON. * For some sequencing programs, System Exclusive messages are not transmitted by the Thru function. If you are using such software and wish to record System Exclusive messages, turn the XP-30s Local Control setting ON.

Sequencer Recording Set to Thru Function On. All performance data that arrives at MIDI IN will be output from MIDI OUT.

MIDI IN MIDI OUT

MIDI OUT MIDI IN Sound Generating Section

Set to Local Off.

Keyboard Controller Section

XP-30

137

Chapter 6

While at this setting, the XP-30s keyboard and controllers are disconnected from the sound generating section, so they will not directly control it.

138

Appendices

139

Appendices

Troubleshooting
If the this unit does not function in the way you expect, first check the following points. If this does not resolve the problem, consult your dealer or a nearby Roland Service Station (listed at the end of this manual). * If a message appears during operation, consult the following section Error Messages (p. 142) - Has the volume been lowered by pedal operations or by MIDI messages (volume messages or expression messages) received from an external MIDI device? Use the Panic function to raise the volume (p. 60). If you are in Performance mode, access the INFO display (PERFORM/INFO) to check the settings of the Volume message (Vol) and Expression message (Exp) parameters, and make the appropriate settings. - Is the rear panel COMPUTER switch set to the correct position? If you are using the XP-30 while connected to a computer, make settings as appropriate for the connection method, the type of computer, and the settings of the driver (p. 134). * Turn off the XP-30s power before changing the position of the COMPUTER switch.

Cannot Turn the Power On


- Is the power cable correctly plugged into an outlet?

No Sound
- Is the power turned on for the other devices connected to the this unit? - Is the VOLUME slider turned all the way down? - Are the connections correct? When using the XP-30 by itself, connect audio cables or headphones (p. 24). When using the XP-30 with a computer, use a Computer cable or MIDI cables to connect it to the computer (p. 134). You will also need to connect audio cables or headphones (p. 24). - Can you hear sound through headphones? If you can hear sound through headphones, the problem may be that the audio cable transmitting the sound to the other devices is broken or incorrectly connected, or that there is a problem with your mixer/amp/speaker system. - If you do not hear sound when you play the keyboard, check whether the Local Switch, a System parameter, is turned OFF. Set the Local parameter (SYSTEM/MIDI/PATCH MIDI, PERFORM MIDI, GM MIDI) to ON (p. 112). - If a layer-type performance is selected, has the Local switch of the part been turned off? Set the Local parameter (PERFORM/MIDI/MIDI) to ON (p. 86). - Have all tones in the patch been turned off? Press the TONE SWITCH [1][4] buttons to make the indicators light. - If you have selected settings that use an XP-D or E Wave, Patch, or Rhythm Set, is the specified Wave Expansion Board installed correctly? (p. 16, 20)

Song Does Not Playback Correctly


- Are you playing a GS format song? The XP-30 is compatible with the General MIDI System, but not with the GS format, so a GS format song will not play back correctly on the XP-30. - When playing back a GM score, is the sound source set to GM mode? Enter GM Mode (p. 124). - Has the Receive GM Exclusive switch been turned ON? Set the Rx.GM parameter (SYSTEM/MIDI/SYS-EXC MIDI) to ON (p. 113).

A Specific Part Does Not Sound


- Has the volume level of the part been lowered? Adjust the Level parameter (PERFORM/PART/SETTING) to raise the volume of the part that is not heard (p. 87). - Is the instrument set to receive MIDI messages? Set the Rx parameter (PERFORM/MIDI/MIDI) to ON (p. 86). - Does the MIDI Receive channel of the Part match the MIDI Transmit channel of the connected MIDI device? Set the Channel parameter (PERFORM/MIDI/MIDI) to specify the MIDI receive channel (p. 86).

No Sound from Connected MIDI Device


- Is the instrument set to transmit MIDI messages? In the Patch mode, make the setting for the Tx-Ch parameter (SYSTEM/MIDI/PATCH MIDI) (p. 112). In the Performance mode, set the Tx parameter (PERFORM/ MIDI/MIDI) to ON (p. 86).

140

Troubleshooting

- Does the MIDI send channel for the XP-30s controller match the MIDI receive channel for the connected MIDI instrument? In the Patch mode, make the setting for the Tx-Ch parameter (SYSTEM/MIDI/PATCH MIDI) (p. 112). In the Performance mode, set the MIDI send channel with the Channel parameter (PERFORM/MIDI/MIDI) (p. 86).

Sounds Are Interrupted


- If you attempt to play more than 64 voices at once, sounds will be interrupted (p. 42). Reduce the number of Tones that you are using (p. 50, 76). Increase the Voice Reserve setting for parts that must not drop out (p. 87).

A Specific Keyboard Area Does Not Sound


- Has a restricted range of notes been set? If a specific range of notes does not sound, check the Key Range settings for the patch and performance in the KEY RANG display (PATCH/COMMON) and KEY RANG display (PERFORM/COMMON). If both key ranges have been set, only the notes specified in both settings will sound.

Exclusive Messages Are Not Received


- Does the Device ID number of the transmitted exclusive message match the Device ID number of this unit? Check the Device# parameter (SYSTEM/MIDI/SYS-EXC MIDI) (p. 113).

This Unit Does Not Transmit MIDI Data


- If you wish to transmit this unit data via the Computer connector, set the COMPUTER switch to PC-1, PC-2 or Mac, depending on the computer or software you are using (p. 134). - When the rear panel COMPUTER switch is set to MIDI, this unit will not transmit data from the COMPUTER connector. In this case, data will be transmitted from the MIDI OUT connector.

Sound Is Distorted
- Is an effect which distorts the sound being applied? (p. 93) - If the sound is distorted for specific patches or parts, lower the volume level of those patches or parts (p. 81, 87). - If all sounds are distorted, use the VOLUME slider to lower the volume level.

Pitch Is Incorrect
- Is the tuning of the XP-30 incorrect? Check the Master parameter (SYSTEM/TUNE/TUNE) (p. 113). - Has the pitch been changed by pedal operations or by pitch change messages received from an external MIDI device? Use the Panic function to reset the original values (p. 60). If you are in Performance mode, access the INFO display (PERFORM/INFO) to check the settings of the Pitch Bend Message parameter (Bend), and make the appropriate settings (p. 87). - Have the Coarse Tune or Fine Tune parameters been set for specific parts? Check the Coarse parameter and Fine parameter (PERFORM/PART/SETTING) (p. 87).

When Using Sequencing Software, Operating the Sliders or Other Controls Does Not Affect the Sound
- Some sequencer software does not soft-thru system exclusive messages. If you are using this type of sequencer software and wish to record system exclusive messages, turn the XP-30s Local parameter ON (p. 112).

- Is the effect switch turned OFF for Multi-Effects, Chorus, or Reverb? To check these settings, press [EFFECTS ON/OFF] (p. 62).

141

Appendices

Effects Do Not Apply

Error Messages
If there has been a mistake in operation, or if the XP-30 is unable to continue processing as you directed, an error message will appear in the display. Take the appropriate action for the displayed error message. This section gives the error messages in alphabetical order.

Memory Card not Ready


Situation: Action: A memory card is not inserted in the MEMORY CARD slot. Turn off the power, and insert a memory card.

Battery Low
Situation: Action: The internal backup battery that is preserving the contents of user memory has run down. Consult your dealer or a nearby Roland service station to have the battery replaced.

Memory Card Write Protected


Situation: Since a write protect sticker is affixed to the memory card, data cannot be saved to the card bank. Remove the write protect sticker from the memory card.

Action:

File Format Error


Situation: The XP-30 cannot handle this file.

MIDI Buffer Full


Situation: Due to an inordinate volume of MIDI messages received, the XP-30 has failed to process them properly. Reduce the amount of MIDI messages to be transmitted.

File I/O Error


Situation: Action: It was not possible to save/load a file. Try the operation once again. If the same message appears, that file has been damaged. Delete the damaged file. Action:

MIDI Communication Error


Situation: Action: A problem has occurred with the MIDI cable connections. Check that MIDI cables are not broken or pulled out.

File Name Duplicate


Situation: Action: A file of the same name exists on the memory card. Use a different file name.

File Name Format Error


Situation: Action: A file name has not been assigned. Assign a file name.

Receive Data Error


Situation: Action: A MIDI message was received incorrectly. If the same error message is displayed repeatedly, there is a problem with the MIDI messages that are being transmitted to the XP30.

File not Found


Situation: Action: The specified file was not found. Insert the memory card that contains the specified file, and try the operation once again.

Unformatted Memory Card


Situation: Action: This memory card cannot be used by the XP-30. Format the memory card on the XP-30.

Memory Card Full


Situation: Action: There is insufficient space available on the memory card to save the data. Either insert a different memory card, or delete unnecessary data and try the operation once again.

User Memory Damaged


Situation: Action: The data in user memory has been lost. Use the Factor Reset function (UTILITY/UTIL 2/FACTORY RESET) to initialize the memory to the factory settings.

Memory Card I/O Error


Situation: Action: It is possible that the memory card has been scratched or otherwise damaged. If the memory card has been damaged, do not use that memory card. If the same error message appears repeatedly, consult your dealer or a nearby Roland service station.

User Memory Write Protected


Situation 1: The Internal parameter (UTILITY/UTIL 1/ PROTECT/WRITE PROTECT) is turned ON. Action 1: Turn the Internal parameter OFF. Situation 2: The Exclusive parameter (UTILITY/UTIL 1/ PROTECT/WRITE PROTECT) is turned ON, and Exclusive messages cannot be received. Action 2: Turn the Exclusive parameter OFF.

142

Quick Reference of Procedures


The XP-30 has a large number of functions. This section gives the procedures for using some of the frequently-used functions. For functions that are used simply by setting the applicable parameter, only the Parameter name (mode/ display group/display) is listed. * [A] + [B] indicates that you are to hold down [A] and press [B]. 7. Use the VALUE dial, [INC]/[DEC], or the numeric keys to modify the value. * If you wish to move to a different parameter group, turn on the [EDIT] indicator.

Changing the Patch Assigned to a Performance


1. Press [PERFORM] + [PATCH]. 2. Use [ ]/[ ] to select a Part.

s Patch Mode
Selecting the Patch Mode PLAY Display
Press [PATCH].

Selecting a Patch
Use the VALUE dial, [INC]/[DEC], or numeric keys to select.

3. Use the VALUE dial, [INC]/[DEC], or the numeric keys to select a Patch. The rest is the same as for the basic procedure listed above.

Using the Numeric Keys to Select the Patch Group


Press [SHIFT] + numeric keys.

Simultaneously Modifying the Values of Two or More Tones


In a Tone setting display, hold down the TONE SELECT [1] [4] (function button) for one Tone, and press the button(s) for the other Tone(s) you want to edit.

Selecting Patches Using the Digit Hold Function


1. Press [SHIFT] + [ENTER] (turn on the Digit Hold function). 2. Use the numeric keys to specify the number of the ones place. * To turn off the Digit Hold function, press [SHIFT] + [ENTER] once again.

Adjusting the Volume of a Patch


Level parameter (PATCH/COMMON/PATCH COMMON)

Adjusting the Pan Position of a Patch


Pan parameter (PATCH/COMMON/PATCH COMMON)

s Performance Mode
Selecting the Performance Mode PLAY Display
Press [PERFORM].

Transposing the Keyboard by Octave


Press [-OCT] or [+OCT].

Transposing the Keyboard in Semitone Steps


Transpose on/off: press [TRANSPOSE] Lower the keyboard: press [TRANSPOSE] + [-OCT] Raise the keyboard: press [TRANSPOSE] + [+OCT]

Selecting a Part to Play from the Keyboard (for a Single-Type Performance)


Use [ ]/[ ].

Modifying a Patch (basic procedure)


1. Make the [EDIT] indicator light. 2. Use the function buttons to select the display group. 3. Use [ ]/[ ] to select the desired display page. 4. Turn off the [EDIT] indicator. 5. Use TONE SELECT [1][4] (function buttons) to select the Tone. 6. Use [ ]/[ ] to select a parameter.

Changing the Patch/Rhythm Set Assigned to a Part


1. Press [PERFORM] + [PATCH]. 2. Use [ ]/[ ] to select a Part.

Using the Numeric Keys to Select the Performance/Patch/Rhythm Set Group


Press [SHIFT] + numeric keys.

143

Appendices

3. Use the VALUE dial, [INC]/[DEC], or the numeric keys to select a Patch or Rhythm Set.

Quick Reference of Procedures

Selecting Performances Using the Digit Hold Function


1. Press [SHIFT] + [ENTER] (turn on the Digit Hold function). 2. Use the numeric keys to specify the number of the ones place. * To turn off the Digit Hold function, press [SHIFT] + [ENTER] once again.

6. Use [ ]/[ ] to select the desired display page. 7. Use [ ]/[ ] to select a parameter.

8. Use the keyboard to select a rhythm instrument. 9. Use the VALUE dial, [INC]/[DEC], or the numeric keys to modify the value.

s Controller Settings
Changing the Range of the Pitch Bend Lever (for each Patch)
Bend Range parameter (PATCH/CONTROL/KEY MODE&BENDER)

Modifying a Performance (basic procedure)


1. Make the [EDIT] indicator light. 2. Use the function buttons to select the display group. 3. Use [ ]/[ ] to select the desired display page. 4. Turn off the [EDIT] indicator. 5. Use [PART] (function button) to select the Tone. 6. Use [ ]/[ ] to select a parameter.

Selecting the MIDI Messages Controlled by the C1C4 Sliders


Assign parameter (SYSTEM/CONTROL/C1C4 ASSIGN)

Selecting the MIDI Messages Controlled by the CONTROL PEDAL


Polarity parameter (SYSTEM/CONTROL/CONTROL PEDAL)

7. Use the VALUE dial, [INC]/[DEC], or the numeric keys to modify the value. * If you wish to move to a different parameter group, turn on the [EDIT] indicator.

Reversing the Polarity of CONTROL PEDAL (when using a pedal of another manufacturer whose polarity is reversed)
Polarity parameter (SYSTEM/CONTROL/CONTROL PEDAL)

Adjusting the Volume of a Part


1. Turn on the [EDIT] indicator. 2. Press [PART] (function button). 3. Use [ ]/[ ] to select the PART SETTING display. 4. Set the Level parameter.

Controlling Patch Parameters with a Slider or Pedal


You can specify up to three control sources (MIDI messages used for control). However control source 1 is fixed at modulation. For each control source, you can specify up to four control destinations (parameters to be controlled). 1. Specify the MIDI message to be controlled by each controller (C1C4, CONTROL PEDAL) (see above). 2. Select the control source. Control 2/3 parameter (PATCH/CONTROL/CONTROL SOURCE) 3. Specify the control destination (the parameter to be controlled). Destination parameter (PATCH/CONTROL/CONTROL13) * If you do not need to set different control sources for each Patch, set the Control 2/3 parameters (PPATCH/CONTROL/ CONTROL SOURCE) to SYS-CTRL1 or SYS-CTRL2, and set the Control 1/2 parameters (SYSTEM/CONTROL/ SYS-CTRL ASSIGN) to the MIDI messages that you wish to use for control.

Adjusting the Pan Position of a Part


1. Turn on the [EDIT] indicator. 2. Press [PART] (function button). 3. Use [ ]/[ ] to select the PART SETTING display. 4. Set the Pan parameter.

Modifying a Rhythm Set (basic procedure)


1. Press [PERFORM] + [PATCH]. 2. Use [ ]/[ ] to select Part 10.

3. Use the VALUE dial, [INC]/[DEC], or the numeric keys to select a Rhythm Set. 4. Make the [EDIT] indicator light. 5. Use the function buttons to select the parameter group.

144

Quick Reference of Procedures

Adjusting the Keyboard Response


Sens parameter (SYSTEM/CONTROL/KEYBOARD)

Saving User Memory Settings and System Settings to Memory Card as a Unit
1. Press [UTIL/CARD]. 2. Select 3: SAVE on the UTIL 2 display. 3. Assign a file name. 4. Press [ENTER].

Set the Keyboard to Produce a Fixed Velocity


Vel parameter (SYSTEM/CONTROL/KEYBOARD)

s Saving and Loading Data


* After completing these procedures, press [UTIL/CARD] to return to the PLAY display.

Deleting a File from Memory Card


1. Press [UTIL/CARD]. 2. Select 1: CARD on the UTIL 2 display. 3. Select 3: DELETE. 4. Select the file that you wish to delete. 5. Press [ENTER].

Formatting a Memory Card


1. Press [UTIL/CARD]. 2. Select 1: CARD on the UTIL 2 display. 3. Select 1: FORMAT. 4. Press [ENTER].

Saving Patch Settings


1. In Patch mode, press [UTIL/CARD]. 2. Select 1: WRITE on the UTIL 1 display. 3. Specify the writing destination. 4. Press [ENTER]. If a message of Internal Write Protect=ON appears, change it to OFF and press [ENTER] twice. * If you wish to hear the sound of the Patch in the selected writing destination, press [UNDO/COMPARE]. Press it once again to return to the previous display.

Checking the Free Area of a Memory Card, etc.


1. Press [UTIL/CARD]. 2. Select 1: CARD on the UTIL 2 display. 3. Select 4: INFO.

s Controlling External MIDI Devices


Changing the Transmit Channel for Patch Mode
Tx-Ch parameter (SYSTEM/MIDI/PATCH MIDI)

Saving Performance Settings


1. In Performance mode, press [UTIL/CARD]. 2. Select 1: WRITE on the UTIL 1 display. 3. Specify the writing destination. 4. Press [ENTER]. If a message of Internal Write Protect=ON appears, change it to OFF and press [ENTER] twice.

Changing the Transmit Channel for Performance Mode (for each Part)
Channel parameter (PERFORM/MIDI/MIDI) * Keyboard and controller movements (MIDI messages) from the controller section are transmitted differently depending on whether a single-type Performance or a layer-type Performance is selected. If a single-type Performance is selected, MIDI messages will be transmitted on the MIDI channel of the Part that is being played by the keyboard. If a layer-type Performance is selected, MIDI messages will be transmitted on the MIDI channel of the Parts whose Tx parameter (PERFORM/MIDI/ MIDI) is turned ON.

Saving Rhythm Set Settings


1. In Rhythm Set mode, press [UTIL/CARD]. 2. Select 1: WRITE on the UTIL 1 display. 3. Specify the writing destination. 4. Press [ENTER]. If a message of Internal Write Protect=ON appears, change it to OFF and press [ENTER] twice.

145

Appendices

Quick Reference of Procedures

Turning Off Transmission of Program Change/Bank Select MIDI Messages (System)


TRANSMIT MIDI display (SYSTEM/MIDI)

Checking the MIDI Message Reception Status (Performance mode)


INFO display (PERFORM/INFO)

s Other
Using the Panic Function
Press [SHIFT] + [PANIC].

Transmitting Bank Select Messages for the Patch Assigned to a Specific Part when a Performance is Selected
1. Set the Bank Select Group parameter (PERFORM/MIDI/ TRANSMIT) to the desired Bank Select Group number (BS1BS7). 2. Save the Performance. 3. In the BANK SEL-GROUP display (SYSTEM/MIDI/ BANK SEL-GROUP), select the Bank Select Group that you specified in step 1. 4. Turn the Switch parameter ON, and specify the MSB and LSB.

Adjusting the Tuning


Master parameter (SYSTEM/TUNE/TUNE)

Adjusting the Display Contrast


LCD Contrast parameter (SYSTEM/SETUP/SYSTEM SETUP)

Restoring the Temporary Performance/Patch/Rhythm Set to the Factory Setting


1. Select a Performance, Patch, or Rhythm Set. 2. Press [UTIL/CARD]. 3. Select 3: INIT on the UTIL 1 display. 4. Select PRESET. 5. Press [ENTER].

s Controlling the XP-30 from an External MIDI Device


Changing the Receive Channel on which Performances will be Selected
Control Channel parameter (SYSTEM/MIDI/PERFORM MIDI)

Changing the Receive Channel of a Part (Performance)


Channel parameter (PERFORM/MIDI/MIDI)

Restoring the XP-30 to the Factory Settings


1. Select a Performance, Patch, or Rhythm Set. 2. Press [UTIL/CARD].

Changing the Receive Channel (Patch)


Rx-Ch parameter (SYSTEM/MIDI/PATCH MIDI)

3. Select 4: FACTORY RESET on the UTIL 2 display. 4. Press [ENTER].

Turning Off Reception of Program Change/Bank Select MIDI Messages (System)


RECEIVE MIDI display (SYSTEM/MIDI)

Turning Reception of Volume/Hold 1/ Program Change MIDI Messages ON/ OFF for Each Part (Performance)
Rx SWITCH display (PERFORM/MIDI)

Turning Reception of Volume/Pan/Pitch Bend/Hold 1/Redamper MIDI Messages ON/OFF for Each Tone (Patch)
Rx SWITCH/DAMPER display (PATCH/CONTROL)

146

Parameter List
s Patch Parameters
* Parameters that can be set independently for each Tone are indicated by T.

COMMON Group (p. 68)


Display PATCH NAME PATCH CATEGORY PATCH CLOCK PATCH COMMON Parameter Category Source Tempo Level Pan Analog Feel Octave Stretch Priority VelRang Lower Upper Cross Fade Lower Upper Type Booster Patch name Patch category Patch clock source Patch tempo Level Pan Analog feel depth Octave shift Stretch tune depth Voice priority Velocity range switch Velocity range lower Velocity range upper Velocity cross fade Key range lower Key range upper Structure type Booster gain Value ASCII Characters (max. 12) (*1) PATCH, SYSETEM 20250 0127 L64063R 0127 -30+3 OFF, 1, 2, 3 LAST, LOUDEST OFF, ON 1Upper Lower127 0127 C-1Upper LowerG9 110 0, +6, +12, +18 dB

VELOCITY

KEY RANG STRUCT

T T T T T T T

*1: NO ASSIGN, AC.PIANO, EL.PIANO, KEYBOARDS, BELL, MALLET, ORGAN, ACCORDION, HARMONICA, AC.GUITAR, EL.GUITAR, DIST.GUITAR, BASS, SYNTH BASS, STRINGS, ORCHESTRA, HIT&STAB, WIND, FLUTE, AC.BRASS, SYNTH BRASS, SAX, HARD LEAD, SOFT LEAD, TECHNO SYNTH, PULSATING, SYNTH FX, OTHER SYNTH, BRIGHT PAD, SOFT PAD, VOX, PLUCKED, ETHNIC, FRETTED, PERCUSSION, SOUND FX, BEAT&GROOVE, DRUMS, COMBINATION

EFFECTS Group (p. 71)


Display OUTPUT Parameter Output Assign Chorus Reverb Type (*1) Mix Out Chorus Reverb Rate Depth Delay Fbk Level Out Type Time Fbk HF Damp Level Output assign Output level Chorus send level Reverb send level EFX type Patch EFX parameter EFX output level Chorus send level Reverb send level EFX control source1, 2 EFX control depth1, 2 Chorus rate Chorus depth Chorus pre delay Chorus feedback level Chorus level Chorus output assign Reverb/Delay type Reverb/Delay time Delay feedback level Reverb/Delay HF damp Reverb/Delay level Value MIX, EFX 0127 0127 0127 (*1) 0127 0127 0127 (*2) -63+63 0127 0127 0127 0127 0127 MIX, REV, M+R ROOM1, ROOM2, STAGE1, STAGE2, HALL1, HALL2, DELAY, PAN-DLY 0127 0127 (*3) 0127 T T T T

PATCH EFX TYPE PATCH EFX PRM PATCH EFX OUT

PATCH EFX CTRL PATCH CHORUS

PATCH REVERB

*1: Refer to EFX parameters. *2: OFF, SYS-CTRL1, SYS-CTRL2, MODULATION, BREATH, FOOT, VOLUME, PAN, EXPRESSION, PITCH BEND, AFTERTOUCH *3: 200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1600, 2000, 2500, 3150, 4000, 5000, 6300, 8000 Hz, BYPASS

147

Appendices

Parameter List

CONTROL Group (p. 73)


Display KEY MODE&BENDER Parameter Assign Legato Bend Range Sw Time Mode Type Start Volume Pan Pitch Bend Hold-1 RxSwitch Redamper EfxCtrl Ctrl 1 Ctrl 2 Ctrl 3 Control 2 Control 3 Destination Depth Destination Depth Destination Depth Key assign mode Solo legato switch Bend range down Bend range up Portamento switch Portamento time Portamento mode Portamento type Portamento start pitch Receive volume switch Receive pan control switch Receive pitch bend switch Receive hold-1 switch Redamper switch EFX control peak/hold Control1 peak/hold Control2 peak/hold Control3 peak/hold Control source 2 Control source 3 Control destination 14 Control depth 14 Control destination 14 Control depth 14 Control destination 14 Control depth 14 Value POLY, SOLO OFF, ON -480 semitone 0+12 semitone OFF, ON 0127 NORMAL, LEGATO RATE, TIME PITCH, NOTE OFF, ON OFF, CONT, KEY-ON OFF, ON OFF, ON OFF, ON OFF, HOLD, PEAK OFF, HOLD, PEAK OFF, HOLD, PEAK OFF, HOLD, PEAK (*1) (*1) (*2) -63+63 (*2) -63+63 (*2) -63+63

PORTAMENTO

RxSWITCH

DAMPER PEAK & HOLD

T T T T T

CONTROL SOURCE CONTROL 1 CONTROL 2 CONTROL 3

T T T T T T

*1: OFF, SYS-CTRL1, SYS-CTRL2, MODULATION, BREATH, FOOT, VOLUME, PAN, EXPRESSION, PITCH BEND, AFTERTOUCH, LFO1, LFO2, VELOCITY, KEYFOLLOW, PLAYMATE *2: OFF, PCH, CUT, RES, LEV, PAN, MIX, CHO, REV, PL1, PL2, FL1, FL2, AL1, AL2, pL1, pL2, L1R, L2R

WAVE Group (p. 76)


Display WAVE Parameter Group Number Gain Switch Switch Color Depth Mode Time Wave group Wave number Wave gain Tone switch Frequency cross modulation switch Frequency cross modulation color Frequency cross modulation depth Tone delay mode Tone delay time Value INT-A, INT-B, XP-A, XP-B, XP-C, XP-D, XP-E 001255 -6, 0, +6, +12 dB OFF, ON OFF, ON 14 116 (*1) 0127/0880/05000 (*2) T T T T T T T T T

FXM

TONE DELAY

*1: NORMAL, HOLD, PLAYMATE, CLOCK-SYNC, KEY-OFF-N, KEY-OFF-D, TEMPO-SYNC *2: When the Tone Delay Mode parameter is set to CLOCK-SYNC this is set as a Note value.

LFO Group (p. 78)


Display LFO1 Parameter Form Key Sync Rate ExtSync Mode Delay Fade Offset (*2) Pitch TVF TVA Pan LFO form LFO key Sync LFO rate LFO external sync LFO fade mode LFO delay time LFO fade time LFO offset Pitch LFO depth 1, 2 TVF LFO depth 1, 2 TVA LFO depth 1, 2 Pan LFO depth 1, 2 Value TRI, SIN, SAW, SQR, TRP, S&H, RND, CHS OFF, ON 0127, 0880 (*1) OFF, CLOCK ON-IN, ON-OUT, OFF-IN, OFF-OUT 0127 0127 -100, -50, 0, +50, +100 -63+63 -63+63 -63+63 -63+63 T T T T T T T T T T T T T

LFO2 LFO DEPTH1:2

*1: When the LFO External Sync parameter is set to CLOCK this is set as a Note value. *2: Same as LFO1.

148

Parameter List

PITCH Group (p. 79)


Display PITCH Parameter Coarse Fine Random Keyfollow Envelope Depth Velocity Sens V-T1 V-T4 Time Keyfollow T1, T2, T3, T4 L1, L2, L3, L4 Coarse tune Fine tune Random pitch depth Pitch keyfollow Pitch envelope depth Pitch envelope velocity sens Pitch envelope time1 velocity sens Pitch envelope time4 velocity sens Pitch envelope time keyfollow Pitch envelope time 14 Pitch envelope level 14 Value -48+48 semitone -50+50 cent 01200 cent (*1) -100+200 (*2) -12+12 -100+150 -100+100 (*3) -100+100 (*3) -100+100 (*3) 0127 -63+63 T T T T T T T T T T T

PCH ENVELOPE PCH TIME ENV

PCH ENVELOPE

*1: 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 20, 30, 40, 50, 60, 70, 80, 90, 100, 200, 300, 400, 500, 600, 700, 800, 900, 1000, 1100, 1200 *2: -100, -70, -50, -30, -10, 0, +10, +20, +30, +40, +50, +70, +100, +120, +150, +200 *3: -100, -70, -50, -40, -30, -20, -10, 0, +10, +20, +30, +40, +50, +70, +100

TVF Group (p. 80)


Display FILTER Parameter Type Cut Res Keyfollow Env Depth V-Sens V-Curve V-Resonance V-T1 V-T4 Time Keyfollow T1, T2, T3, T4 L1, L2, L3, L4 Filter type Cutoff frequency Resonance Cutoff frequency keyfollow TVF envelope depth TVF envelope velocity sens TVF envelope velocity curve Resonance velocity sens TVF envelope time1 velocity sens TVF envelope time4 velocity sens TVF envelope time keyfollow TVF envelope time 14 TVF envelope level 14 Value OFF, LPF, BPF, HPF, PKG 0127 0127 -100+200 (*1) -63+63 -100+150 1 7 -100+150 -100+100 (*2) -100+100 (*2) -100+100 (*2) 0127 0127 T T T T T T T T T T T T T

TVF VELOCITY

TVF TIME ENV

TVF ENVELOPE

*1:-100, -70, -50, -30, -10, 0, +10, +20, +30, +40, +50, +70, +100, +120, +150, +200 *2: -100, -70, -50, -40, -30, -20, -10, 0, +10, +20, +30, +40, +50, +70, +100

TVA Group (p. 81)


Display TVA Parameter Level Pan V-Sens V-Curve Bias Point Direction Keyfollow Random Alternate V-T1 V-T4 Time Keyfollow T1, T2, T3, T4 L1, L2, L3 Level Pan TVA envelope velocity sens TVA envelope velocity curve Bias level Bias point Bias direction Pan keyfollow Random pan depth Alternate pan depth TVA envelope time1 velocity sens TVA envelope time4 velocity sens TVA envelope time keyfollow TVA envelope time 14 TVA envelope level 13 Value 0127 L64063R -100+150 1 7 -100+100 (*1) C-1G9 LOWER, UPPER, LOWER&UPPER, ALL -100+100 (*1) 063 L63063R -100+100 (*1) -100+100 (*1) -100+100 (*1) 0127 0127 T T T T T T T T T T T T T T T

BIAS

PAN MODULATE

TVA TIME ENV

TVA ENVELOPE

*1: -100, -70, -50, -40, -30, -20, -10, 0, +10, +20, +30, +40, +50, +70, +100

149

Appendices

Parameter List

s Performance Parameters
* Parameters that can be set independently for each Part are indicated by P.

COMMON Group (p. 83)


Display PERFORM NAME PERFORM CLOCK PERFORM COMMON KEY RANG KEYBOARD Parameter Source Tempo Key Mode Key Range Lower Upper Octave Shift Performance name Performance clock source Performance tempo Key mode key range switch Key range lower Key range upper Octave shift Value ASCII Characters (max. 12) PERFORM, SYSTEM 20250 LAYER, SINGLE OFF, ON C-1Upper LowerG9 -3+3

P P P

EFFECTS Group (p. 84)


Display OUTPUT Parameter Output Assign Chorus Reverb Type Source (*1) Mix Out Chorus Reverb Output assign Output level Chorus send level Reverb send level EFX type EFX source Performance EFX parameters EFX output level Chorus send level Reverb send level EFX control source 1 EFX control depth 1 EFX control source 2 EFX control depth 2 Chorus rate Chorus depth Chorus pre delay Chorus feedback level Chorus level Chorus output assign Reverb/Delay type Reverb/Delay time Delay feedback level Reverb/Delay HF damp Reverb/Delay level Value MIX, EFX, PATCH 0127 0127 0127 (*1) PERFORM, 19, 1116 0127 0127 0127 (*2) -63+63 (*2) -63+63 0127 0127 0127 0127 0127 MIX, REV, M+R ROOM1, ROOM2, STAGE1, STAGE2, HALL1, HALL2, DELAY, PAN-DLY 0127 0127 (*3) 0127 P P P P

PERFORM EFX TYPE PERFORM EFX PRM PERFORM EFX OUT

PERFORM EFX CTRL

PERFORM CHORUS

PERFORM REVERB

Rate Depth Delay Fbk Level Out Type Time Fbk HF Damp Level

*1: Refer to EFX parameters. *2: OFF, SYS-CTRL1, SYS-CTRL2, MODULATION, BREATH, FOOT, VOLUME, PAN, EXPRESSION, PITCH BEND, AFTERTOUCH *3: 200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1600, 2000, 2500, 3150, 4000, 5000, 6300, 8000 Hz, BYPASS

MIDI Group (p. 86)


Display MIDI Parameter Channel MIDI channel Rx Receive switch Tx Transmit switch Local Local switch Volume Receive volume switch Hold-1 Receive hold-1 switch Program Change Receive program change switch BankSelectGroup Transmit bank select group Transmit Volume Transmit volume Value 116 OFF, ON OFF, ON OFF, ON OFF, ON OFF, ON OFF, ON PATCH, BS1BS7 0127, OFF P P P P P P P P P

RxSWITCH

TRANSMIT

150

Parameter List

PART Group (p. 87)


Display PATCH Parameter Group Number Level Pan Coarse Fine Voice Reserve Patch group Patch number Level Pan Coarse tune Fine tune Voice reserve Value USER, PR-A, PR-B, PR-C, GM, PR-E, XP-A, XP-B, XP-C, XP-D, XP-E 001256 0127 L64063R -48+48 semitone -50+50 cent 064 P P P P P P P

SETTING

RESERVE

INFORMATION Group (p. 87)


Display INFO Parameter Mod Breath Foot Vol Pan Exp Hold Bend Aft Sys1 Sys2 Voices Modulation information Breath information Foot information Volume information Pan information Expression information Hold1 information Pitch bend information Aftertouch information System control 1 information System control 2 information Voice information Value 0127 0127 0127 0127 L64063R 0127 0127 -128+127 0127 0127/-128+127 0127/-128+127 064 P P P P P P P P P P P P

s Rhythm Set Parameters


COMMON Group (p. 88)
Display RHYTHM NAME Parameter Rhythm set name Value ASCII Characters (max. 12)

EFFECTS Group (p. 88)


Display OUTPUT Parameter Output Assign Chorus Reverb Type Source (*1) Mix Out Chorus Reverb Output assign Output level Chorus send level Reverb send level EFX type EFX source Performance EFX parameters EFX output level Chorus send level Reverb send level EFX control source 1 EFX control depth 1 EFX control source 2 EFX control depth 2 Chorus rate Chorus depth Chorus pre delay Chorus feedback level Chorus level Chorus output assign Reverb/Delay type Reverb/Delay time Delay feedback level Reverb/Delay HF damp Reverb/Delay level Value MIX, EFX 0127 0127 0127 (*1) PERFORM, 19, 1116 0127 0127 0127 (*2) -63+63 (*2) -63+63 0127 0127 0127 0127 0127 MIX, REV, M+R ROOM1, ROOM2, STAGE1, STAGE2, HALL1, HALL2, DELAY, PAN-DLY 0127 0127 (*3) 0127

PERFORM EFX TYPE PERFORM EFX PRM PERFORM EFX OUT

PERFORM EFX CTRL

PERFORM CHORUS

PERFORM REVERB

*1: Refer to EFX parameters. *2: OFF, SYS-CTRL1, SYS-CTRL2, MODULATION, BREATH, FOOT, VOLUME, PAN, EXPRESSION, PITCH BEND, AFTERTOUCH *3: 200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1600, 2000, 2500, 3150, 4000, 5000, 6300, 8000 Hz, BYPASS

151

Appendices

Rate Depth Delay Fbk Level Out Type Time Fbk HF Damp Level

Parameter List

CONTROL Group (p. 90)


Display CONTROL Parameter Bend Range Env Mode Mute Group Volume Pan Hold-1 Bend range Envelope mode Mute group Receive volume switch Receive pan control switch Receive hold-1 switch Value 012 NO-SUS, SUSTAIN OFF, 131 OFF, ON OFF, CONT, KEY-ON OFF, ON

RxSWITCH

WAVE Group (p. 90)


Display WAVE Parameter Group Number Gain Switch Wave group Wave number Wave gain Key switch Value INT-A, INT-B, XP-A, XP-B, XP-C, XP-D, XP-E 001255 -6, 0, +6, +12 dB OFF, ON

PITCH Group (p. 91)


Display PITCH Parameter Coarse Fine Random Env Depth Velocity Sens Velocity Time T1, T2, T3, T4 L1, L2, L3, L4 Coarse tune Fine tune Random pitch depth Pitch envelope depth Pitch envelope velocity sens Pitch envelope time velocity sens Pitch envelope time 14 Pitch envelope level 14 Value C-1G9 -50+50 cent 01200 cent (*1) -12+12 -100+150 -100+100 (*2) 0127 -63+63

PCH VELOCITY PCH ENVELOPE

*1: 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 20, 30, 40, 50, 60, 70, 80, 90, 100, 200, 300, 400, 500, 600, 700, 800, 900, 1000, 1100, 1200 *2: -100, -70, -50, -40, -30, -20, -10, 0, +10, +20, +30, +40, +50, +70, +100

TVF Group (p. 91)


Display FILTER Parameter Type Cutoff Resonance Env Depth V-Sens V-Time V-Resonance T14 L14 Filter type Cutoff frequency Resonance TVF Envelope depth TVF envelope velocity sens TVF envelope time velocity sens Resonance velocity sens TVF envelope time 14 TVF envelope level 14 Value OFF, LPF, BPF, HPF, PKG 0127 0127 -63+63 -100+150 -100+100 (*1) -100+150 0127 0127

TVF VELOCITY

TVF ENVELOPE

*2: -100, -70, -50, -40, -30, -20, -10, 0, +10, +20, +30, +40, +50, +70, +100

TVA Group (p. 92)


Display TVA Parameter Level Pan Random Alternate Velocity Sens Velocity Time T14 L13 Level Pan Random pan depth Alternate pan depth TVA envelope velocity sens TVA envelope time velocity sens TVA envelope time 14 TVA envelope level 13 Value 0127 L64063R 063 L63063R -100+150 -100+100 (*1) 0127 0127

TVA VELOCITY TVA ENVELOPE

*1: -100, -70, -50, -40, -30, -20, -10, 0, +10, +20, +30, +40, +50, +70, +100

152

Parameter List

s GM Mode Parameters
* Parameters that can be set independently for each Part are indicated by P.

EFFECTS Group (p. 125)


Display OUTPUT Parameter Output Assign Chorus Reverb Type (*1) Mix Out Chorus Reverb Rate Depth Delay Fbk Level Out Type Time Fbk HF Damp Level Output assign Output level Chorus send level Reverb send level EFX type GM EFX parameters EFX output level Chorus send level Reverb send level Chorus rate Chorus depth Chorus pre delay time Chorus feedback level Chorus level Chorus output assign Reverb/Delay type Reverb/Delay time Delay Feedback level Reverb/Delay HF damp Reverb/Delay level Value MIX, EFX 0127 0127 0127 (*1) 0127 0127 0127 0127 0127 0127 0127 0127 MIX, REV, M+R ROOM1, ROOM2, STAGE1, STAGE2, HALL1, HALL2, DELAY, PAN-DLY 0127 0127 (*2) 0127 P P P P

GM EFX TYPE GM EFX PRM GM EFX OUT

GM CHORUS

GM REVERB

*1: Refer to EFX parameters. *2: 200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1600, 2000, 2500, 3150, 4000, 5000, 6300, 8000 Hz, BYPASS

PART Group (p. 127)


Display PATCH SETTING Parameter Number Volume Pan Coarse Fine GMPatch number Volume Pan Coarse tune Fine tune Value 001128 0127 L64063R -48+48 semitone -50+50 cent P P P P P

INFORMATION Group (p. 127)


Display INFO Parameter Mod Breath Foot Vol Pan Exp Hold Bend Aftertouch Voices Modulation information Breath information Foot information Volume information Pan information Expression information Hold1 information Pitch bend information Aftertouch information Voice information Value 0127 0127 0127 0127 L64063R 0127 0127 -128+127 0127 064 P P P P P P P P P P

153

Appendices

Parameter List

s EFX Parameters
1: STEREO-EQ (p. 93)
Parameter LowFreq LowGain Hi Freq Hi Gain P1 Freq P1 Q P1 Gain P2 Freq P2 Q P2 Gain Level Low frequency Low gain High frequency Hi gain Peaking1 frequency Peaking1 Q Peaking1 gain Peaking2 frequency Peaking2 Q Peaking2 gain Output level Value 200, 400 Hz -15+15 dB 4000, 8000 Hz -15+15 dB 2008000Hz (*1) 0.5, 1.0, 2.0, 4.0, 8.0 -15+15 dB 2008000 Hz (*1) 0.5, 1.0, 2.0, 4.0, 8.0 -15+15 dB 0127

6: ENHANCER (p. 94)


Parameter Sens Mix Low Gain Hi Gain Level Sens Mix level Low gain High gain Output level Value 0127 0127 -15+15 dB -15+15 dB 0127

7: AUTO-WAH (p. 95)


Parameter Filter Sens Manual Peak Rate Depth Level Filter type Sens Manual Peak Rate Depth Output level Value LPF, BPF 0127 0127 0127 0.0510.00 Hz 0127 0127

*1: 200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1600, 2000, 2500, 3150, 4000, 5000, 6300, 8000 Hz

2: OVERDRIVE (p. 93)


Parameter Drive Level LowGain Hi Gain AmpType Pan Drive Output level Low gain High gain Amp simulator type Output pan Value 0127 0127 -15+15 dB -15+15 dB SMALL, BUILT-IN, 2-STACK, 3-STACK L64063R

8: ROTARY (p. 95)


Parameter LowSlow LowFast LowAccl Low Lvl Hi Slow Hi Fast Hi Accl Hi Lvl Separation Speed Level Low frequency slow rate Low frequency fast rate Low frequency acceleration Low frequency level High frequency slow rate High frequency fast rate High frequency acceleration High frequency level Separation Speed Output level Value 0.0510.00 Hz 0.0510.00 Hz 015 0127 0.0510.00 Hz 0.0510.00 Hz 015 0127 0127 SLOW, FAST 0127

3: DISTORTION (p. 93)


Parameter Drive Level LowGain Hi Gain AmpType Pan Drive Output level Low gain High gain Amp simulator type Output pan Value 0127 0127 -15+15 dB -15+15 dB SMALL, BUILT-IN, 2-STACK, 3-STACK L64063R

9: COMPRESSOR (p. 96)


Parameter Attack Sustain Post Gain LowGain Hi Gain Pan Level Attack Sustain Post gain Low gain High gain Output pan Output level Value 0127 0127 0, +6, +12, +18 dB -15+15 dB -15+15 dB L64063R 0127

4: PHASER (p. 94)


Parameter Manual Rate Depth Res Mix Pan Level Manual Rate Depth Resonance Mix level Output pan Output level Value 1008000 Hz 0.0510.00 Hz 0127 0127 0127 L64063R 0127

10: LIMITER (p. 96)


Parameter Thresh Ratio Release Gain LowGain Hi Gain Pan Level Threshold level Compression ratio Release time Post gain Low gain High gain Output pan Output level Value 0127 1.5:1, 2:1, 4:1, 100:1 0127 0, +6, +12, +18 dB -15+15 dB -15+15 dB L64063R 0127

5: SPECTRUM (p. 94)


Parameter Band 1 Band 2 Band 3 Band 4 Band 5 Band 6 Band 7 Band 8 Q Pan Level Band1 gain Band2 gain Band3 gain Band4 gain Band5 gain Band6 gain Band7 gain Band8 gain Q Output pan Output level Value -15+15 dB -15+15 dB -15+15 dB -15+15 dB -15+15 dB -15+15 dB -15+15 dB -15+15 dB 0.5, 1.0, 2.0, 4.0, 8.0 L64063R 0127

11: HEXA-CHORUS (p. 96)


Parameter Pre Dly Rate Depth Dly Dev Dpt Dev Pan Dev Balance Level Pre delay time Rate Depth Pre delay deviation Depth deviation Pan deviation Effect balance Output level Value 0.0100.0 ms 0.0510.00 Hz 0127 020 -20+20 020 D100:0WD0:100W 0127

154

Parameter List

12: TREMOLO-CHORUS (p. 97)


Parameter Pre Dly ChoRate Cho Dpt Phase TrmRate Trm Sep Balance Level Pre delay time Chorus rate Chorus depth Tremolo phase Tremolo rate Tremolo separation Effect balance Output level Value 0.0100.0 ms 0.0510.00 Hz 0127 0180 degree 0.0510.00 Hz 0127 D100:0WD0:100W 0127

17: STEREO-DELAY (p. 99)


Parameter Delay L Delay R Fbk Mode Phase L Phase R HF Damp LowGain Hi Gain Balance Level Delay time left Delay time right Feedback level Feedback mode Feedback phase left Feedback phase right HF damp Low gain High gain Effect balance Output level Value 0.0500.0 ms 0.0500.0 ms -98+98% NORMAL, CROSS NORMAL, INVERT NORMAL, INVERT 2008000 Hz, BYPASS (*1) -15+15 dB -15+15 dB D100:0WD0:100W 0127

13: SPACE-D (p. 97)


Parameter Pre Dly Rate Depth Phase LowGain Hi Gain Balance Level Pre delay time Rate Depth Phase Low gain High gain Effect balance Output level Value 0.0100.0 ms 0.0510.00 Hz 0127 0180 degree -15+15 dB -15+15 dB D100:0WD0:100W 0127

*1: 200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1600, 2000, 2500, 3150, 4000, 5000, 6300, 8000 Hz, BYPASS

18: MODULATION-DELAY (p. 99)


* ParameterValue Delay L Delay R Fbk Mode Rate Depth Phase HF Damp LowGain Hi Gain Balance Level Delay time left Delay time right Feedback level Feedback mode Rate Depth Phase HF damp Low gain High gain Effect balance Output level 0.0500.0 ms 0.0500.0 ms -98+98% NORMAL, CROSS 0.0510.00 Hz 0127 0180 degree 2008000 Hz, BYPASS (*1) -15+15 dB -15+15 dB D100:0WD0:100W 0127

14: STEREO-CHORUS (p. 97)


Parameter Pre Dly Rate Depth Phase Filter Type Cutoff LowGain Hi Gain Balance Level Pre delay time Rate Depth Phase Filter type Cutoff frequency Low gain High gain Effect balance Output level Value 0.0100.0 ms 0.0510.00 Hz 0127 0180 degree OFF, LPF, HPF 2008000 Hz (*1) -15+15 dB -15+15 dB D100:0WD0:100W 0127

*1: 200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1600, 2000, 2500, 3150, 4000, 5000, 6300, 8000 Hz, BYPASS

*1: 200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1600, 2000, 2500, 3150, 4000, 5000, 6300, 8000 Hz

19: TRIPLE-TAP-DELAY (p. 100)


Parameter Value Delay time center Delay time left Delay time right Feedback level Center level Left level Right level HF damp Low gain High gain Effect balance Output level 2001000 ms, note 2001000 ms, note 2001000 ms, note -98+98% 0127 0127 0127 2008000 Hz, BYPASS (*1) -15+15 dB -15+15 dB D100:0WD0:100W 0127 Delay C Delay L Delay R Fbk Level C Level L Level R HF Damp LowGain Hi Gain Balance Level

15: STEREO-FLANGER (p. 98)


Parameter Pre Dly Rate Depth Fbk Phase Filter Type Cutoff LowGain Hi Gain Balance Level Pre delay time Rate Depth Feedback level Phase Filter type Cutoff frequency Low gain High gain Effect balance Output level Value 0.0100.0 ms 0.0510.00 Hz 0127 -98+98% 0180 degree OFF, LPF, HPF 2008000 Hz (*1) -15+15 dB -15+15 dB D100:0WD0:100W 0127

*1: 200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1600, 2000, 2500, 3150, 4000, 5000, 6300, 8000 Hz

*1: 200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1600, 2000, 2500, 3150, 4000, 5000, 6300, 8000 Hz, BYPASS

Parameter Pre Dly Rate Depth Fbk Phase Step Rate LowGain Hi Gain Balance Level Pre delay time Rate Depth Feedback level Phase Step rate Low gain High gain Effect balance Output level

Value 0.0100.0 ms 0.0510.00 Hz 0127 -98+98% 0180 degree 0.1020.00 Hz, note -15+15 dB -15+15 dB D100:0WD0:100W 0127

155

Appendices

16: STEP-FLANGER (p. 98)

Parameter List

20: QUADRUPLE-TAP-DELAY (p. 101)


Parameter Delay 1 Delay 2 Delay 3 Delay 4 Level 1 Level 2 Level 3 Level 4 Fbk HF Damp Balance Level Delay time 1 Delay time 2 Delay time 3 Delay time 4 Level 1 Level 2 Level 3 Level 4 Feedback level HF damp Effect balance Output level Value 2001000 ms, note 2001000 ms, note 2001000 ms, note 2001000 ms, note 0127 0127 0127 0127 -98+98% 2008000 Hz, BYPASS (*1) D100:0WD0:100W 0127

24: REVERB (p. 103)


Parameter Type Reverb type Value ROOM1, ROOM2, STAGE1, STAGE2, HALL1, HALL2 0.0100.0 ms 0127 2008000 Hz, BYPASS (*1) -15+15 dB -15+15 dB D100:0WD0:100W 0127

Pre Dly Time HF Damp LowGain Hi Gain Balance Level

Pre delay time Gate time HF damp Low gain High gain Effect balance Output level

*1: 200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1600, 2000, 2500, 3150, 4000, 5000, 6300, 8000 Hz, BYPASS

*1: 200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1600, 2000, 2500, 3150, 4000, 5000, 6300, 8000 Hz, BYPASS

25: GATE-REVERB (p. 103)


Parameter Type Pre Dly Gate Time LowGain Hi Gain Balance Level Gate-Reverb type Pre delay time Gate time Low gain High gain Effect balance Output level Value NORMAL, REVERSE, SWEEP1, SWEEP2 0.0100.0 ms 5500 ms -15+15 dB -15+15 dB D100:0WD0:100W 0127

21: TIME-CONTROL-DELAY (p. 101)


Parameter Delay Accel Fbk HF Damp Pan LowGain Hi Gain Balance Level Delay time Acceleration Feedback level HF damp Output pan Low gain High gain Effect balance Output level Value 2001000 ms 015 -98+98% 2008000 Hz, BYPASS (*1) L64063R -15+15 dB -15+15 dB D100:0WD0:100W 0127

26: OVERDRIVECHORUS (p. 103)


Parameter OD Drive OD Pan Cho Dly ChoRate Chorus Depth Chorus Balance Level Drive Over drive pan Chorus pre delay time Chorus Rate Chorus depth Chorus balance Output level Value 0127 L64063R 0.0100.0 ms 0.0510.00 Hz 0127 D100:0WD0:100W 0127

*1: 200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1600, 2000, 2500, 3150, 4000, 5000, 6300, 8000 Hz, BYPASS

22: 2 VOICE-PITCH-SHIFTER (p. 102)


Parameter CoarseA Fine A Pan A PreDlyA CoarseB Fine B Pan B PreDlyB Mode Lvl Bal Balance Level Coarse pitch A Fine pitch A Output pan A Pre delay time A Coarse pitch B Fine pitch B Output pan B Pre delay time B Pitch shifter mode Level balance Effect balance Output level Value -24+12 semitone -100+100 cent L64063R 0.0500.0 ms -24+12 semitone -100+100 cent L64063R 0.0500.0 ms 1, 2, 3, 4, 5 A100:0BA0:100B D100:0WD0:100W 0127

27: OVERDRIVEFLANGER (p. 104)


Parameter OD Drive OD Pan Flg Dly FlgRate Flg Dpt Flg Fbk Flanger Balance Level Drive Over drive pan Flanger pre delay time Flanger rate Flanger depth Flanger feedback level Flanger balance Output level Value 0127 L64063R 0.0100.0 ms 0.0510.00 Hz 0127 -98+98% D100:0WD0:100W 0127

23: FBK-PITCH-SHIFTER (p. 102)


Parameter Coarse Fine Fbk Pre Dly Mode Pan LowGain Hi Gain Balance Level Coarse pitch Fine pitch Feedback level Pre delay time Pitch shifter mode Output pan Low gain High gain Effect balance Output level Value -24+12 semitone -100+100 cent -98+98% 0.0500.0 ms 1, 2, 3, 4, 5 L64063R -15+15 dB -15+15 dB D100:0WD0:100W 0127

28: OVERDRIVEDELAY (p. 104)


Parameter OD Drive OD Pan DlyTime Dly Fbk Delay HF Damp Delay Balance Level Drive Over drive pan Delay time Delay feedback level Delay HF damp Delay balance Output level Value 0127 L64063R 0.0500.0 ms -98+98% 2008000 Hz, BYPASS (*1) D100:0WD0:100W 0127

*1: 200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1600, 2000, 2500, 3150, 4000, 5000, 6300, 8000 Hz, BYPASS

156

Parameter List

29: DISTORTIONCHORUS (p. 104)


The parameters are essentially the same as "26: OVERDRIVE CHORUS," with the exception of the following two. OD Drive Dist Drive, OD Pan Dist Pan

36: FLANGERDELAY (p. 106)


Parameter Flg Dly FlgRate Flg Dpt Flg Fbk Flg Bal DlyTime Dly Fbk HF Damp Delay Balance Level Flanger pre delay time Flanger rate Flanger depth Flanger feedback level Flanger balance Delay time Delay feedback level HF damp Delay balance Output level Value 0.0100.0 ms 0.0510.00 Hz 0127 -98+98% D100:0WD0:100W 0.0500.0 ms -98+98% 2008000 Hz, BYPASS (*1) D100:0WD0:100W 0127

30: DISTORTIONFLANGER (p. 105)


The parameters are essentially the same as "27: OVERDRIVE FLANGER," with the exception of the following two. OD Drive Dist Drive, OD Pan Dist Pan

31: DISTORTIONDELAY (p. 105)


The parameters are essentially the same as "28: OVERDRIVE DELAY," with the exception of the following two. OD Drive Dist Drive, OD Pan Dist Pan

*1: 200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1600, 2000, 2500, 3150, 4000, 5000, 6300, 8000 Hz, BYPASS

32: ENHANSERCHORUS (p. 105)


Parameter Enhancer Sens Enhancer Mix Cho Dly ChoRate Chorus Depth Chorus Balance Level Enhancer sens Enhancer mix level Chorus pre delay time Chorus rate Chorus depth Chorus balance Output level Value 0127 0127 0.0100.0 ms 0.0510.00 Hz 0127 D100:0WD0:100W 0127

37: CHORUSFLANGER (p. 107)


Parameter Cho Dly ChoRate Cho Dpt Cho Bal Flg Dly FlgRate Flg Dpt Flg Fbk Flanger Balance Level Chorus pre delay time Chorus rate Chorus depth Chorus balance Flanger pre delay time Flanger rate Flanger depth Flanger feedback level Flanger balance Output level Value 0.0100.0 ms 0.0510.00 Hz 0127 D100:0WD0:100W 0.0100.0 ms 0.0510.00 Hz 0127 -98+98% D100:0WD0:100W 0127

33: ENHANSERFLANGER (p. 105)


Parameter Enhancer Sens Enhancer Mix Flg Dly FlgRate Flg Dpt Flg Fbk Flanger Balance Level Enhancer sens Enhancer mix level Flanger pre delay time Flanger rate Flanger depth Flanger feedback level Flanger balance Output level Value 0127 0127 0.0100.0 ms 0.0510.00 Hz 0127 -98+98% D100:0WD0:100W 0127

38: CHORUS/DELAY (p. 107)


Refer to 35: CHORUSDELAY.

39: FLANGER/DELAY (p. 107)


Refer to 36: FLANGER DELAY.

34: ENHANSERDELAY (p. 106)


Parameter Enhancer Sens Enhancer Mix Delay Dly Fb Delay HF Damp Delay Balance Level Enhancer sens Enhancer mix level Delay time Delay feedback level Delay HF damp Delay balance Output level Value 0127 0127 0.0500.0 ms -98+98% 2008000 Hz, BYPASS (*1) D100:0WD0:100W 0127

40: CHORUS/FLANGER (p. 107)


Refer to 37: CHORUSFLANGER.

*1: 200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1600, 2000, 2500, 3150, 4000, 5000, 6300, 8000 Hz, BYPASS

35: CHORUSDELAY (p. 106)


Parameter Cho Dly ChoRate Cho Dpt Cho Bal DlyTime Dly Fbk Delay HF Damp Delay Balance Level Chorus pre delay time Chorus rate Chorus depth Chorus balance Delay time Delay Feedback level Delay HF damp Delay balance Output level Value 0.0100.0 ms 0.0510.00 Hz 0127 D100:0WD0:100W 0.0500.0 ms -98+98% 2008000 Hz, BYPASS (*1) D100:0WD0:100W 0127

*1: 200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1600, 2000, 2500, 3150, 4000, 5000, 6300, 8000 Hz, BYPASS

157

Appendices

Parameter List

s System Parameters
SETUP Group (p. 108)
Display SYSTEM SETUP Parameter LCD Power Up Mode Patch Remain Clock Source System Tempo Category Select Mode LCD contrast Power up mode Patch remain switch Clock source System tempo Category select mode Value 110 LAST-SET, DEFAULT OFF, ON INT, MIDI 20250 LAST-SET, DEFAULT

ARPEGGIO Group (p. 108)


Display ARPEGGIO Parameter Style Octave Range Motif Beat Pattern Accent Rate Shuffle Rate Key Velocity Part Tempo Style Octave range Motif Beat pattern Accent rate Shuffle rate Key velocity Arpeggio part Tempo Value (*1) -3+3 (*2) (*3) 0100% 5090% REAL, 1127 116 20250

*1: 1/4, 1/6, 1/8, 1/12, 1/16, 1/32, PORTAMENTO A, PORTAMENTO B, GLISSANDO, SEQUENCE A, SEQUENCE B, SEQUENCE C, SEQUENCE D, ECHO, SYNTH BASS, SLAP BASS A, SLAP BASS B, WALK BASS, RHYTHM GTR A, RHYTHM GTR B, RHYTHM GTR C, RHYTHM GTR D, RHYTHM GTR E, 3 FINGER GTR, STRUMMING GTR, KBD COMPING A, KBD COMPING B, KBD COMPING C, KBD COMPING D, KBD COMPING E, PERCUSSION, HARP, SHAMISEN, BOUND BALL, RANDOM, BOSSA NOVA, SALSA, MAMBO, LATIN PERCUSSION, SAMBA, TANGO, HOUSE, LIMITLESS *2: SINGLE UP, SINGLE DOWN, SINGLE UP&DOWN, SINGLE RANDOM, DUAL UP, DUAL DOWN, DUAL UP&DOWN, DUAL RANDOM, TRIPLE UP, TRIPLE DOWN, TRIPLE UP&DOWN, TRIPLE RANDOM, NOTE ORDER, GLISSANDO, CHORD, BASS+CHORD15, BASS+UP18, BASS+RANDOM13, TOP+UP16, BASS+UP+TOP *3: 1/4, 1/6, 1/8, 1/12, 1/16 13, 1/32 13, PORTA-A 0111, PORTA-B 0115, SEQ-A 17, SEQ-B 15, SEQ-C 12, SEQ-D 18, ECHO 13, MUTE 0116, STRUM 18, REGGAE12, REFRAIN 12, PERC14, WALKBS, HARP, BOUND, RANDOM, BOSSA NOVA, SALSA 14, MAMBO 12, CLAVE, REV CLA, GUIRO, AGOGO, SAMBA, TANGO 14, HOUSE 12

CONTROL Group (p. 110)


Display KEYBOARD Parameter Transpose Sens Vel Aft Output Polarity Assign Output Polarity Assign Output Control 1/2 Hold Peak Volume Aftertouch Transpose switch Transpose value Keyboard sens Keyboard velocity Aftertouch sens Pedal output Pedal polarity Pedal assign Pedal output Pedal polarity C1/C2/C3/C4 slider assign C1/C2/C3/C4 slider output System control assign 1/2 Hold control source Peak control source Volume control source Aftertouch control source Value OFF, ON -5 (G)+6 (F#) LIGHT, MEDIUM, HEAVY REAL, 1127 0100 OFF, INT, MIDI, BOTH STANDARD, REVERSE (*1) OFF, INT, MIDI, BOTH STANDARD, REVERSE (*2) OFF, INT, MIDI, BOTH (*2) OFF, HOLD1, SOST, SOFT, HOLD2 OFF, HOLD1, SOST, SOFT, HOLD2 VOLUME, VOL&EXP CHANNEL, POLY, CH&POLY

HOLD PEDAL CONTROL PEDAL

C1/2/3/4 ASSIGN SYS-CTRL ASSIGN CONTROL SOURCE

*1: CC0095 (except for 6, 32-63), PITCH BEND, AFTERTOUCH, PROG-UP, PROG-DOWN, TAP-TEMPO, OCT-UP, OCT-DOWN *2: CC0095 (except for 6, 32-63), PITCH BEND, AFTERTOUCH

158

Parameter List

MIDI Group (p. 112)


Display PERFORM MIDI Parameter Control Channel Local Remote Rx-Ch Tx-Ch Local Remote Local Switch Program Change Bank Select Program Bank Sel Active Sensing Device# Rx.Exc Tx.Edit Rx.GM Number Switch MSB LSB Performance control channel Local switch Remote keyboard switch Patch mode receive channel Patch mode transmit channel Local switch Remote keyboard switch Local switch Receive program change switch Receive bank select switch Transmit program change switch Transmit bank select switch Transmit active sensing switch Exclusive device ID number Receive exclusive switch Transmit edit data switch Receive GM exclusive switch Bank select group number Bank select transmit switch Bank select MSB Bank select LSB Value 116, OFF OFF, ON OFF, ON 116 116, Rx-Ch, OFF OFF, ON OFF, ON OFF, ON OFF, ON OFF, ON OFF, ON OFF, ON OFF, ON 1732 OFF, ON OFF, ON OFF, ON 17 OFF, ON 0127 0127

PATCH MIDI

GM MIDI RECEIVE MIDI TRANSMIT MIDI

SYS-EXC MIDI

BANK-SEL GROUP

PREVIEW Group (p. 113)


Display PREVIEW MODE PREVIEW KEY PREVIEW VELOCITY Parameter Mode Note 14 Note 14 Preview sound mode Preview Note Set 14 Preview velocity Value SINGLE, CHORD, PHRASE C-1G9 0127

TUNE Group (p. 113)


Display TUNE Parameter Master Key Shift Scale Tune C B CB Master tune Key shift Scale tune switch Scale tune CB Scale tune CB Value 427.4452.6 Hz -12+12 semitone OFF, ON -64+63 cent -64+63 cent

PATCH SCALE KEY SCALE

PGM CHNG Group (p. 114)


Display TRANSMIT P.C Parameter Channel P.C# Bnk-MSB Bnk-LSB Transmit MIDI channel Transmit program change Transmit bank select MSB Transmit bank select LSB Value 116 1128 0127 0127

INFO Group (p. 114)


Display INFO EXP BATTERY CHECK Parameter Expansion D Expansion E Internal Battery Expansion board name D Expansion board name E Battery check Value

LOW, OK

159

Appendices

Waveform List
INT-A (Internal A)
No. 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 049 050 051 Name Ac Piano1 A Ac Piano1 B Ac Piano1 C Ac Piano2 pA Ac Piano2 pB Ac Piano2 pC Ac Piano2 fA Ac Piano2 fB Ac Piano2 fC Piano Thump Piano Up TH MKS-20 P3 A MKS-20 P3 B MKS-20 P3 C SA Rhodes 1A SA Rhodes 1B SA Rhodes 1C SA Rhodes 2A SA Rhodes 2B SA Rhodes 2C E.Piano 1A E.Piano 1B E.Piano 1C E.Piano 2A E.Piano 2B E.Piano 2C E.Piano 3A E.Piano 3B E.Piano 3C MK-80 EP A MK-80 EP B MK-80 EP C D-50 EP A D-50 EP B D-50 EP C Celesta Music Box Clav 1A Clav 1B Clav 1C Organ 1 Jazz Organ 1 Jazz Organ 2 Organ 2 Organ 3 Organ 4 Rock Organ Dist. Organ Rot.Org Slw Rot.Org Fst Pipe Organ No. 052 053 054 055 056 057 058 059 060 061 062 063 064 065 066 067 068 069 070 071 072 073 074 075 076 077 078 079 080 081 082 083 084 085 086 087 088 089 090 091 092 093 094 095 096 097 098 099 100 101 102 Name Nylon Gtr A Nylon Gtr B Nylon Gtr C 6-Str Gtr A 6-Str Gtr B 6-Str Gtr C Gtr Harm A Gtr Harm B Gtr Harm C Comp Gtr A Comp Gtr B Comp Gtr C Comp Gtr A+ Mute Gtr 1 Mute Gtr 2A Mute Gtr 2B Mute Gtr 2C Pop Strat A Pop Strat B Pop Strat C Jazz Gtr A Jazz Gtr B Jazz Gtr C JC Strat A JC Strat B JC Strat C JC Strat A+ JC Strat B+ JC Strat C+ Clean Gtr A Clean Gtr B Clean Gtr C Stratus A Stratus B Stratus C OD Gtr A OD Gtr B OD Gtr C OD Gtr A+ Heavy Gtr A Heavy Gtr B Heavy Gtr C Heavy Gtr A+ Heavy Gtr B+ Heavy Gtr C+ PowerChord A PowerChord B PowerChord C EG Harm Gt.FretNoise Syn Gtr A No. 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 Name Syn Gtr B Syn Gtr C Harp 1A Harp 1B Harp 1C Banjo A Banjo B Banjo C Sitar A Sitar B Sitar C Dulcimer A Dulcimer B Dulcimer C Shamisen A Shamisen B Shamisen C Koto A Koto B Koto C Pick Bass A Pick Bass B Pick Bass C Fingerd Bs A Fingerd Bs B Fingerd Bs C E.Bass Fretless A Fretless B Fretless C UprightBs 1 UprightBs 2A UprightBs 2B UprightBs 2C Slap Bass 1 Slap & Pop Slap Bass 2 Slap Bass 3 Jz.Bs Thumb Jz.Bs Slap 1 Jz.Bs Slap 2 Jz.Bs Slap 3 Jz.Bs Pop Syn Bass A Syn Bass C Mini Bs 1A Mini Bs 1B Mini Bs 1C Mini Bs 2 Mini Bs 2+ MC-202 Bs A No. 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 Name MC-202 Bs B MC-202 Bs C Flute 1A Flute 1B Flute 1C Blow Pipe Bottle Shakuhachi Clarinet A Clarinet B Clarinet C Oboe mf A Oboe mf B Oboe mf C Sop.Sax mf A Sop.Sax mf B Sop.Sax mf C Alto Sax 1A Alto Sax 1B Alto Sax 1C Tenor Sax A Tenor Sax B Tenor Sax C Bari.Sax f A Bari.Sax f B Bari.Sax f C Harmonica A Harmonica B Harmonica C Chanter Tpt Sect. A Tpt Sect. B Tpt Sect. C Trumpet 1A Trumpet 1B Trumpet 1C Trumpet 2A Trumpet 2B Trumpet 2C HarmonMute1A HarmonMute1B HarmonMute1C Trombone 1 French 1A French 1C F.Horns A F.Horns B F.Horns C Violin A Violin B Violin C No. 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 Name Cello A Cello B Cello C ST.Strings-R ST.Strings-L MonoStringsA MonoStringsC Pizz JP Strings1A JP Strings1B JP Strings1C JP Strings2A JP Strings2B JP Strings2C Soft Pad A Soft Pad B Soft Pad C Fantasynth A Fantasynth B Fantasynth C D-50 HeavenA D-50 HeavenB D-50 HeavenC Fine Wine D-50 Brass A D-50 Brass B D-50 Brass C D-50 BrassA+ DualSquare A DualSquare C DualSquareA+ Pop Voice Syn Vox 1 Syn Vox 2 Voice Aahs A Voice Aahs B Voice Aahs C Voice Oohs1A Voice Oohs1B Voice Oohs1C Voice Oohs2A Voice Oohs2B Voice Oohs2C Voice Breath Male Ooh A Male Ooh B Male Ooh C Org Vox A Org Vox B Org Vox C Vox Noise

* * * * *

*: Waveform marked * are One-shot type waveforms (non-sustaining).

160

Waveform List

INT-B (Internal B)
No. 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 049 050 051 Name Kalimba Marimba Wave Log Drum Vibes Bottle Hit Glockenspiel Tubular Steel Drums Fanta Bell A Fanta Bell B Fanta Bell C FantaBell A+ Org Bell Agogo DIGI Bell 1 DIGI Bell 1+ DIGI Chime Wave Scan Wire String 2.2 Bellwave 2.2 Vibwave Spark VOX MMM VOX Lead Wave Synth Reed Synth Saw 1 Synth Saw 2 Syn Saw 2inv Synth Saw 3 JP-8 Saw A JP-8 Saw B JP-8 Saw C P5 Saw A P5 Saw B P5 Saw C D-50 Saw A D-50 Saw B D-50 Saw C Synth Square JP-8 SquareA JP-8 SquareB JP-8 SquareC Synth Pulse1 Synth Pulse2 Triangle Sine Org Click White Noise Pink Noise Metal Wind Wind Agogo No. 052 053 054 055 056 057 058 059 060 061 062 063 064 065 066 067 068 069 070 071 072 073 074 075 076 077 078 079 080 081 082 083 084 085 086 087 088 089 090 091 092 093 094 095 096 097 098 099 100 101 102 Name Feedbackwave Spectrum BreathNoise Rattles Ice Rain Tin Wave Anklungs Wind Chimes Orch. Hit Tekno Hit Back Hit Philly Hit Scratch 1 Scratch 2 Scratch 3 Natural SN1 Natural SN2 Piccolo SN Ballad SN SN Roll 808 SN Brush Slap Brush Swish Brush Roll Dry Stick Side Stick Lite Kick Hybrid Kick1 Hybrid Kick2 Old Kick Verb Kick Round Kick 808 Kick Verb Tom Hi Verb Tom Lo Dry Tom Hi Dry Tom Lo Cl HiHat 1 Cl HiHat 2 Op HiHat Pedal HiHat 606 HiHat Cl 606 HiHat Op 808 Claps Hand Claps Finger Snaps Ride 1 Ride 2 Ride Bell 1 Crash 1 China Cym No. 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 Name Cowbell 1 Wood Block Claves Bongo Hi Bongo Lo Cga Open Hi Cga Open Lo Cga Mute Hi Cga Mute Lo Cga Slap Timbale Cabasa Up Cabasa Down Cabasa Cut Maracas Long Guiro Tambourine Open Triangl Cuica Vibraslap Timpani Applause REV Orch.Hit REV TeknoHit REV Back Hit REV PhillHit REV Steel DR REV Tin Wave REV NatrlSN1 REV NatrlSN2 REV PiccloSN REV BalladSN REV Side Stk REV SN Roll REV Brush 1 REV Brush 2 REV Brush 3 REV LiteKick REV HybridK1 REV HybridK2 REV Old Kick REV Timpani REV VerbTomH REV VerbTomL REV DryTom H REV DryTom M REV ClHiHat1 REV ClHiHat2 REV Op HiHat REV Pedal HH REV 606HH Cl * * * * * * * * * * * * * * * * * * No. 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 Name REV 606HH Op REV Ride REV Cup REV Crash 1 REV China REV DrySick REV RealCLP REV FingSnap REV Cowbell REV WoodBlck REV Clve REV Conga REV Tamb REV Maracas REV Guiro REV Cuica REV Metro Loop 1 Loop 2 Loop 3 Loop 4 Loop 5 Loop 6 Loop 7 R8 Click Metronome 1 Metronome 2 MC500 Beep 1 MC500 Beep 2 Low Saw Low Saw inv Low P5 Saw Low Pulse 1 Low Pulse 2 Low Square Low Sine Low Triangle Low White NZ Low Pink NZ DC *

* * * * * * * * * * * * * * * * * * * * * * * *

* * * * * * * * * * * * * *

* * * *

* * * *

* * * * * * * * * * * * * * *

* * * * * * *

* * * * *

*: Waveform marked * are One-shot type waveforms (non-sustaining).

161

Appendices

Waveform List

XP-A (WAVE EXPANSION A: Session)


No. 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 042 Name StGrand L pA StGrand L pB StGrand L pC StGrand R pA StGrand R pB StGrand R pC StGrand L fA StGrand L fB StGrand L fC StGrand R fA StGrand R fB StGrand R fC OrcStrings A OrcStrings B OrcStrings C Choir Aah A Choir Aah B Choir Aah C Choir Mmh A Choir Mmh B Choir Mmh C D.Solo Gtr A D.Solo Gtr B D.Solo Gtr C D.MuteGt p A D.MuteGt p B D.MuteGt p C D.MuteGt mpA D.MuteGt mpB D.MuteGt mpC D.MuteGt mfA D.MuteGt mfB D.MuteGt mfC Clean TC 1 A Clean TC 1 B Clean TC 1 C Clean TC2 pA Clean TC2 pB Clean TC2 pC Clean TC2 fA Clean TC2 fB Clean TC2 fC No. 043 044 045 046 047 048 049 050 051 052 053 054 055 056 057 058 059 060 061 062 063 064 065 066 067 068 069 070 071 072 073 074 075 076 077 078 079 080 081 082 083 084 Name NylonGt2 p A NylonGt2 p B NylonGt2 p C NylonGt2 mfA NylonGt2 mfB NylonGt2 mfC NylonGt2 f A NylonGt2 f B NylonGt2 f C P.Bass 3 A P.Bass 3 B P.Bass 3 C Jazz Bass3 A Jazz Bass3 B Jazz Bass3 C Muted Bass A Muted Bass B Muted Bass C Blow Sax A Blow Sax B Blow Sax C T.Sax hrd A T.Sax hrd B T.Sax hrd C Flute Vib A Flute Vib B Flute Vib C R&R Horns A R&R Horns B R&R Horns C Solo Tpt. A Solo Tpt. B Solo Tpt. C F.AccordionA F.AccordionB F.AccordionC Vibraphone A Vibraphone B Vibraphone C VocalWave2 A VocalWave2 B VocalWave2 C No. 085 086 087 088 089 090 091 092 093 094 095 096 097 098 099 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 Name JP Hollo A JP Hollo B JP Hollo C Hard 5ths A Hard 5ths B Hard 5ths C Blaster A Blaster B Blaster C Juno Rave A Juno Rave B Juno Rave C Wah Gtr MENU Wah Down 1 Wah Up 1 Wah Down 2 Wah Up 2 Gtr FX MENU Gtr Feedback Gtr Scrap Gtr Slid Nz Gtr Cut Nz Gtr Slap FX MENU Sm.Club Sm.Club fw Sm.Club lp FX Bell 1 FX Bell 1fw FX Bell 2 FX Bell 2fw Auhvox Tekno Hit 2 Tekno Hit 3 Tekno Loop FX Bomb Kick MENU Deep Kick 3 TD7 Kick Dance Kick 2 Dance Kick 3 Mix Kick No. 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 Name Kick Ghost Snr&Tom MENU Loose Snr Ring Snr 808 Snr 2 909 Snr 2 909 Snr 3 90s Snare Solo Snr Rap Snr Talk Snr Jingle Snr House Snr Snr Buzz Tiny Snr 2 Mute Snr 909 Rim 2 909 Tom 2 Clp&Snp MENU 909 Claps 2 HC2 Claps 1 707 Claps HC2 Claps 2 FingerSnaps2 FingerSnap 3 Bongo3 MENU Bongo3 Low Bongo3 High Tambrin MENU Tamb.Short Tamb.Long CR78 Tamb. Shaker MENU2 626 Shaker Shaker 3 Shaker 4 Shaker 5 REV Gt Scrap REV Gt SldNz REV Gt CutNz REV Gt Slap REV TeknHit2 * No. 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 Name REV TeknHit3 REV Deep K 3 REV TD7 Kick REV Dance K2 REV Dance K3 REV Mix Kick REV K.Ghost REV LooseSnr REV Ring Snr REV 808 Snr2 REV 909 Snr2 REV 909 Snr3 REV 90s Snr REV Solo Snr REV Rap Snr REV Talk Snr REV JinglSnr REV HouseSnr REV Snr Buzz REV TinySnr2 REV Mute Snr REV 909 Rim2 REV 909 Tom2 REV 909 Clp2 REV HC2 Clp1 REV 707 Clps REV HC2 Clp2 REV F.Snaps2 REV F.Snap 3 REV Bongo3 L REV Bongo3 H REV Tamb.Sht REV Tamb.Lng REV CR78Tamb REV 626Shakr REV Shaker 3 REV Shaker 4 REV Shaker 5

*:These are Menu Waveforms. Many different Waveforms are provided, each one assigned to a different key.

162

Waveform List

q XP-A Menu Waveforms


Menu Waveforms provide multiple Waveforms, with each one assigned to a different key.
97 Key C D E F Wah Gtr MENU No. Name Wah Down 1 Wah Up 1 Wah Down 2 Wah Up 2 121 Key C D E F G A 4 4 4 4 4 4 Kick MENU No. 122 123 124 125 126 127 Name Deep Kick 3 TD7 Kick Dance Kick 2 Dance Kick 3 Mix Kick Kick Ghost 145 Key C D E F G A 4 4 4 4 4 4 Clp&Snp MENU No. 146 147 148 149 150 151 Name 909 Claps 2 HC2 Claps 1 707 Claps HC2 Claps 2 FingerSnaps2 FingerSnap 3

4 98 4 99 4 100 4 101

102 Key C D E F G 4 4 4 4 4

Gtr FX MENU No. 103 104 105 106 107 Name Gtr Feedback Gtr Scrap Gtr Slid Nz Gtr Cut Nz Gtr Slap

128 Key C D E F G A B C D E F G A B C D 4 4 4 4 4 4 4 5 5 5 5 5 5 5 6 6

Snr&Tom MENU No. 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 Name Loose Snr Ring Snr 808 Snr 2 909 Snr 2 909 Snr 3 90s Snare Solo Snr Rap Snr Talk Snr Jingle Snr House Snr Snr Buzz Tiny Snr 2 Mute Snr 909 Rim 2 909 Tom 2

152 Key

Bongo3 MENU No. Name Bongo3 Low Bongo3 High

C 4 153 D 4 154

155 Key

Tambrin MENU No. Name Tamb.Short Tamb.Long CR78 Tamb.

108 Key C D E F G A B C D E F G 4 4 4 4 4 4 4 5 5 5 5 5

FX MENU No. 116 109 110 111 112 113 114 115 117 118 119 120 Name Auhvox Sm.Club Sm.Club fw Sm.Club lp FX Bell 1 FX Bell 1fw FX Bell 2 FX Bell 2fw Tekno Hit 2 Tekno Hit 3 Tekno Loop FX Bomb

C 4 156 D 4 157 E 4 158

159 Key C D E F 4 4 4 4

Shaker MENU2 No. 160 161 162 163 Name 626 Shaker Shaker 3 Shaker 4 Shaker 5

163

Appendices

Waveform List

XP-B (WAVE EXPANSION B: Orchestral)


No. 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 Name Vl Sect A Vl Sect B Vl Sect C Va Sect A Va Sect B Va Sect C Vc Sect A Vc Sect B Vc Sect C Cb Sect Multi STR A Multi STR B Multi STR C Vl Sect Lp Va Sect Lp Vc Sect Lp Cb Sect Lp Multi STR Lp Vl Solo A Vl Solo B Vl Solo C Va Solo A Va Solo B Va Solo C Vc Solo A Vc Solo B Vc Solo C Cb Solo Multi Solo 1 Multi Solo 2 Vls Spicc A Vls Spicc B Vls Spicc C Vas Spicc A Vas Spicc B No. 036 037 038 039 040 041 042 043 044 045 046 047 048 049 050 051 052 053 054 055 056 057 058 059 060 061 062 063 064 065 066 067 068 069 070 Name Vas Spicc C Vcs Spicc A Vcs Spicc B Vcs Spicc C Cbs Spicc A Cbs Spicc B Cbs Spicc C Multi Spicc VlSolo Spicc VcSolo Spicc MultSl Spicc STR Attack Pizzicato 1 Pizzicato 2 Piccolo Oboe 1A Oboe 1B Oboe 1C Oboe 2A Oboe 2B Oboe 2C Eng.Horn A Eng.Horn B Eng.Horn C Clarinet Bs Clarinet Multi Cla Bassoon Multi Reed Tnr.Recorder F.Horn Solo F.Horn Sect1 F.Horn Sect2 F.Horn Mute Trumpet 2 No. 071 072 073 074 075 076 077 078 079 080 081 082 083 084 085 086 087 088 089 090 091 092 093 094 095 096 097 098 099 100 101 102 103 104 105 Name Flugelhorn Cornet HarmonMute2A HarmonMute2B HarmonMute2C Solo Tb A Solo Tb B Solo Tb C Bass Tb Tb Sect Tuba BRS Ensemble Brass ff Full Orch. Orch Hit Maj Orch Hit Min Orch Hit Dim Choir A Choir B Choir C F.Hrn Sc1 Lp F.Hrn Sc2 Lp F.Hrn MuteLp Tb Sect Lp BRS Ens Lp ff Brass Lp Full Orch Lp Breath Wind Breath Atack Breath Whisl Breath Hrmon EuroPiano pA EuroPiano pB EuroPiano pC EuroPiano fA No. 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 Name EuroPiano fB EuroPiano fC Harpsichord Celesta A Celesta B Celesta C Harp A Harp B Harp C Glockenspiel Xylophone Bass Marimba TubularBells Church Bells Timpani p Timpani f Timp Roll p Timp Roll f Concert SNR1 Concert SNR2 Concert SNR3 SNR Roll Concert BD 1 Concert BD 2 Concert BD 3 BD Roll Crash Cymbal Crash Cym Lp Cymbal Hit Tam Tam Gong Perc Hit 1 Perc Hit 2 Triangle Castanets 1 No. 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 Name Castanets 2 Slapstick Ratchet Sleigh Bell Tambourine Wind Chime 2 REV Hit Maj REV Hit Min REV Hit Dim REV Bell REV Timp 1 REV Timp 2 REV SNR 1 REV SNR 2 REV SNR 3 REV BD 1 REV BD 2 REV BD 3 REV BD Roll REV Crash REV Cym Hit REV Tam Tam REV Gong REV PercHit1 REV PercHit2 REV Casta 1 REV Casta 2 REV S.Stick REV Sleigh REV Tamb SNR Set Perc Set 1 Perc Set 2 Perc Set 3

164

Waveform List

XP-C (WAVE EXPANSION C: Techno Collection)


No. 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 049 050 051 Name PHRASE MENU 120:House 1 120:House 2 120:House 3 120:TeknoBNG 144:Tekno BD 144:TeknoHAT 160:DrumnBs 184:Gabba 132:Detroit 132:Agogo 116:Elect80 120:Electro1 138:Electro2 TB Dst Saw TB Dst Sqr 1 TB Dst Sqr 2 TB Reso Sqr1 TB Reso Sqr2 TB Reso Sqr3 TB Saw TB Solid Saw TB Reso Saw TB Square 1 TB Square 2 TB Square 3 Octa Bass Rave Bass FM Pluck Bs FM Slide Bs Solid Bass JUNO-60 Bass SH-5 Bass Dirty Bass Sub Bass Jungle Bass JP8000 Saw 1 JP8000 Saw 2 JP-6 Saw Techno Saw SH-1 Square SH-1 Pulse JP8000 PWM JP8000 FBK 260 Sub OSC Dist Synth Dist Square P5 Pipe FM Garage JUNO Pluck Funky Synth * ** ** ** ** ** ** ** ** ** ** ** ** ** No. 052 053 054 055 056 057 058 059 060 061 062 063 064 065 066 067 068 069 070 071 072 073 074 075 076 077 078 079 080 081 082 083 084 085 086 087 088 089 090 091 092 093 094 095 096 097 098 099 100 101 102 Name JUNO Bowing JUNO Synth JX Synth Alpha Wave Killer Detuned Saw Fat JP-6 Euro Dance Noisy 101 Daft Wave Pizzy Techno Organ Pizz Garage Org FM Club Org Org Chord Dist TekGtr1 Dist TekGtr2 GTR FX MENU JP Siren Cold Dress HIT MENU 1 HIT MENU 2 Beam HiQ Analog Bird ElectronFall Retro UFO Jungle Beep PC-2 Machine Dr.Beat Mental Perc May Day Perc PC-2 Spacers Techno Scene Pure Psycho TAO Hit Thin Beef Organ Hit 2 INDUST. MENU PCM Press ElectricDunk Thrill Drill Hit MachineShout Air Gun Emergency Buzzer Tonality Aah Formant Eeh Formant Iih Formant Ooh Formant No. 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 Name Uuh Formant Dist Ooh Vox Talkbox VOCODER MENU * TOM MENU * TR909 Tom TR909 DstTom TR808 Tom TR606 Tom TR606 CmpTom TR707 Tom TR707 CmpTom Deep Tom Kick Tom Natural Tom Can Tom PERCUSS MENU * TR808 Conga1 TR808 Conga2 Surdo mute Surdo open TMB&SKR MENU * Tambourine 2 Rattle Tamb TechnoShaker Dance Shaker COW&RIM MENU * TR808Cowbell TR707Cowbell CR78 Cowbell TR727 Agogo TR909 Rim TR808 Rim TR808 RimLng TR808 Claves CHH MENU 1 * CHH MENU 2 * TR909 CHH 1 TR909 CHH 2 TR909 CHH 3 TR808 CHH 1 TR808 CHH 2 TR606 CHH TR707 CHH CR78 CHH Pop CHH Bristol CHH PHH MENU * TR909 PHH 1 TR909 PHH 2 TR808 PHH No. 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 Name TR606 PHH TR707 PHH OHH MENU TR909 OHH 1 TR909 OHH 2 TR909 OHH 3 TR909 DstOHH TR808 OHH TR606 DstOHH TR707 OHH CR78 OHH R8 OHH Cym OHH CYMBAL MENU TR606 Cym 1 TR606 Cym 2 TR606 DstCym TR909 Ride TR909DstRide TR707 Ride TR909 Crash TR909DsCrash CLAP MENU TR909 Clap TS Clap Clap Stop TR707 Clap HC2 Dry Clap Scratch Clap Comp Clap Claptail SNR MENU 1 SNR MENU 2 SNR MENU 3 SNR MENU 4 SNR MENU 5 TR909 Snr 1 TR909 Snr 2 TR909 Snr 3 TR909 Snr 4 TR909 Snr 5 TR909 Snr 6 TR909 Snr 7 TR808 Snr 1 TR808 Snr 2 TR808 Snr 3 TR808 Snr 4 TR606 Snr 1 TR606 Snr 2 TR606 Snr 3 TR707 Snr 1 No. 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 Name TR707 Snr 2 CR78 Snare Headz Snare Deep Snare Fat Snare Antigua Snr MC Snare DJ Snare Macho Snare Clap Snare Rage Snare Indus Snare TekRok Snare Jungle Snr 1 Jungle Snr 2 Jungle Snr 3 Jungle Snr 4 SideStiker Ragga Snr 2 Lo-Fi Snare Jungle Snr 5 Urban Snare Sim Snare Roll Snare KICK MENU 1 KICK MENU 2 TR909 Kick 1 TR909 Kick 2 Plastic BD 1 Plastic BD 2 TR808 Kick 1 TR808 Kick 2 TR808 Kick 3 TR606 Kick 1 TR606 Kick 2 TR707 Kick 1 TR707 Kick 2 Culture Kick Optic Kick Lo-Fi BD Wet Kick Video Kick JungleKick 1 Street Kick Turbo Kick JungleKick 2 Tekno Kick Sim Kick Amsterdam BD TR909 Dst BD Roll Kick

* *

* *

* * * * *

*: These are Menu Waveforms. Many different Waveforms are provided, each one assigned to a different key. **: These are the phrase loop waveforms. The numbers (116184) included in the wave name represent the B.P.M. (tempo) when played at the C4 key. And these waveforms can be synchronized to a device such as a sequencer.

165

Appendices

Waveform List

q XP-C Menu Waveforms


Menu Waveforms provide multiple Waveforms, with each one assigned to a different key.
*: This waveform is used only in the MENU WAVEFORM. 1 Key C 4 C# 4 D 4 D# 4 E 4 F 4 F# 4 G 4 G# 4 A 4 A# 4 B 4 C 5 PHRASE MENU No. 2 3 4 5 6 7 8 9 10 11 12 13 14 Name 120:House 1 120:House 2 120:House 3 120:TeknoBNG 144:Tekno BD 144:TeknoHat 160:DrumnBs 184:Gabba 132:Detroit 132:Agogo 116:Elect80 120:Electro1 138:Electro2 73 Key C 4 C# 1 D 4 D# 4 E 4 F 4 F# 4 G 4 G# 4 A 4 A# 4 HIT MENU 2 No. 84 85 86 87 88 Name Techno Scene Pure Psycho TAO Hit Thin Beef Techno Tone * Organ Hit 2 Scratch 4 * Scratch PUSH * Scratch PULL * Tape RWD * Reel Stop * 106 Key C 4 C# 4 D 4 D# 4 E 4 F 4 F# 4 G 4 G# 4 A 4 A# 4 B 4 C 5 C# 5 D 5 D# 5 VOCODER MENU No. Name VP ei * VP ii * VP ai * VP ou * VP ju * VP one * VP two * VP three * VP four * VP music * VP techno * VP groove * VP dance * VP funky * VP rhythm * VP machine * 119 Key C 4 C# 4 D 4 D# 4 E 4 F 4 F# 4 G 4 G# 4 A 4 A# 4 B 4 C 5 PERCUSS MENU No. 120 121 Name TR808 Conga1 TR808 Conga3* TR808 Conga2 Hi Bongo L.F * Lo Bongo L.F * Mute CGA L.F * Hi Conga L.F * Lo Conga L.F * Surdo mute Surdo open H Timbal L.F * L Timbal L.F * Tabla Comp * 138 Key C 4 C# 4 D 4 D# 4 E 4 F 4 F# 4 G 4 G# 4 A 4 A# 4 B 4 C 5 CHH MENU 1 No. 140 141 142 143 144 145 Name TR909 CHH 1 TR909 CHH 2 TR909 CHH 3 TR808 CHH 1 TR808 CHH 3 TR808 CHH 2 TR808 CHH 3 TR606 CHH TR606 CHH 2 TR606 CHH 3 TR707 CHH CR78 CHH DM CHH

* * * *

122 123

146 147

89 Key

INDUST MENU No. Name Indust Bomb Door Comp PCM Press ElectricDunk Thrill Drill Hit MachineShout Air Gun Swish Emergency Buzzer TB reso Tonality * *

69 Key C 4 C# 4

GTR FX MENU No. Name GTR FX 1 GTR FX 2 * *

72 Key C 4 C# 4 D 4 D# 4 E 4 F 4 F# 4 G 4 G# 4 A 4 A# 4 B 4 C 5 # 5

HIT MENU 1 No. 74 Name Beam Hiq Noise Click * Electro Prc * Anaolog Bird ElectronFall Retro UFO Jungle Beep PC-2 Machine Dance Prc * Dr.Beat CR78 Beat * Mental Perc May Day Perc PC-2 Spacers

75 76 77 78 79 80 81 82 83

C 4 C# 4 D 4 D# 4 E 4 F 4 F# 4 G 4 G# 4 A 4 A# 4 B 4 C 5

124 Key

TMB&SKR MENU No. 125 126 127 128 Name Tambourine 2 Battle Tamb TechnoShaker Dance Shaker TR808 Maracas CR78 Guiro *

139 Key C C# D D# E

CHH MENU 2 No. Name Pop CHH Pop CHH 2 Bristol CHH Lithe CHH R8 CHH * * *

90 91 92 93 94 95 96 97 98

107 Key

TOM MENU No. Name TR909 Tom TR909 DstTom TR808 Tom TR606 Tom TR606 TR707 Tom TR707 Deep Tom Kick Tom Natural Tom Can Tom

C 4 108 C# 4 109 D 4 110 D# 4 111 E 4 112 CmpTom F 4 113 F# 4 114 CmpTom G 4 115 G# 4 116 A 4 117 A# 4 118

C C# D D# E * F

4 4 4 4 4 4

4 148 4 4 149 4 4

150 Key

PHH MENU No. 151 152 153 154 155 Name TR909 PHH 1 TR909 PHH 2 TR808 PHH TR808 PHH 2 * TR606 PHH TR606 PHH 2 * TR707 PHH HH Pedal *

129 Key C 4 C# 4 D 4 D# 4 E 4 F 4 F# 4 G 4 G# 4 A 4 A# 4

COW&RIM MENU No. 130 131 132 133 134 135 136 Name TR808Cowbell TR707Cowbell CR78 Cowbell TR727 Agogo TR909 Rim TR909 Dst Rim* TR808 Rim TR808 RimLng TR707 Rim * Ragga Rim * TR808 Claves

C 4 C# 4 D 4 D# 4 E 4 F 4 F# 4 G 4

137

166

Waveform List

156 Key C 4 C# 4 D 4 D# 4 E 4 F 4 F# 4 G 4 G# 4 A 4 A# 4 B 4 C 5 C# 5 D 5 D# 5

OHH MENU No. 157 158 159 160 161 162 163 164 Name TR909 OHH 1 TR909 OHH 2 TR909 OHH 4 * TR909 OHH 3 TR909 DstOHH TR808 OHH 2 * TR808 OHH TR808 OHH 3 * TR606 DstOHH TR707 HH * TR707 OHH CR78 OHH DM OHH * Hop OHH * R8 OHH Cym OHH

176 Key C 4 C# 4 D 4 D# 4 E 4 F 4 F# 4 G 4 G# 4 A 4 A# 4 B 4 C 5 C# 5

CLAP MENU No. 177 178 179 180 181 182 Name TR909 Clap TS Clap TR909 Clap 2 * Clap Stop 808 Comp Clp * TR707 Clap HC2 Dry Clap DM Clap * Scratch Clap Real Clap * Groove Clap * Comp Clap Claptail 909 Clp Fuzz *

186 Key C 4 C# 4 D 4 D# 4 E 4 F 4 F# 4 G 4 G# 4 A 4 A# 4 B 4 C 5

SNR MENU 2 No. 201 202 203 204 205 206 Name TR606 Snr 1 TR606 Snr 2 606 Snr Dst TR606 Snr 3 TR707 Snr 1 TR707 Snr 3 TR707 snr 2 CR78 Snare Clap Snare 2 Jungle Snr 9 Rage Snare 2 Clap Snare 3 Clap Snare 4

188 Key C 4 C# 4 D 4 D# 4 E 4 F 4 F# 4 G 4 G# 4 A 4 A# 4

SNR MENU 4 No. 218 219 220 221 222 Name Jungle Snr 1 Jungle Snr 2 Jungle Snr 3 Jungle Snr 6 * Jungle Snr 4 Jungle Snr 7 * SideStickr Cross Snr * Jungle Rim * Ragga Snr 2 Lo-fi Snare

229 Key C 4 C# 4 D 4 D# 4 E 4 F 4 F# 4 G 4 G# 4 A 4 A# 4 B 4 C 5 C# 5 D 5

KICK MENU 1 No. 231 232 233 234 235 236 237 238 239 240 241 242 Name TR909 Kick 1 TR909 Kick 2 TR909 Kick 3 * Plastic BD 1 Plastic BD 2 TR909 Kick 4 * TR808 Kick 1 TR808 Kick 2 TR808 Kick 3 TR606 Kick 1 TR606 Kick 2 606 Dst Kick * TR707 Kick 1 TR707 Kick 1 Culture Kick

183 184

* * * * *

223 224

189 Key

SNR MENU 5 No. 225 226 227 228 Name Jungle Snr 10 Jungle Snr 5 Jungle Snr 8 Urban Snare Lite Snare Sim Snare Electro Snr Roll Snare * * * *

165 166

187 185 Key SNR MENU 1 No. 190 191 192 193 194 195 196 Name TR909 Snr 1 TR909 Snr 2 TR909 Snr 3 TR909 Snr 4 TR909 Snr 5 TR909 Snr 8 TR909 Snr 6 TR909 Snr 7 909 Snr Dst 909 Snr Fuzz TR808 Snr 5 TR808 Snr 1 TR808 Snr 2 TR808 Snr 3 TR808 Snr 4 TR808 Snr 6 Key C 4 C# 4 D 4 D# 4 E 4 F 4 F# 4 G 4 G# 4 A 4 A# 4 B 4 C 5 C# 5 D 5

SNR MENU 3 No. 207 208 209 210 211 212 213 Name Headz Snare Deep Snare Fat Snare R&B Snare * Antigua Snr MC Snare DJ Snare Macro Snare Lofi Snare * Pistol Snr * Clap Snare Rage Snare Indus Snare TekRok Snare Indus Snare *

167 Key C 4 C# 4 D 4 D# 4 E 4 F 4 F# 4 G 4

CYMBAL MENU No. 168 169 170 171 172 173 174 175 Name TR606 Cym 1 TR606 Cym 2 TR606 DstCym TR909 Ride TR909DstRide TR707 Ride TR909 Crash TR909DsCrash

C 4 C# 4 D 4 D# 4 E 4 F 4 F# 4 G 4 G# 4 A 4 A# 4 B 4 C 5 C# 5 D 5 D# 5

C 4 C# 4 D 4 D# 4 E 4 F 4 F# 4 G 4

230 Key C 4 C# 4 D 4 D# 4 E 4 F 4 F# 4 G 4 G# 4 A 4 A# 4 B 4 C 5 C# 5 D 5 D# 5

KICK MENU 2 No. 243 244 245 246 247 248 249 250 251 252 253 254 255 Name Hop Kick * Optic Kick Lo-Fi BD Wet Kick DR Cmp Kick * Video Kick JungleKick 1 Street Kick Turbo Kick JungleKick 2 Tekno KIck Sim Kick Dance Kick 2 * Amsterdam BD TR909 Dst BD Roll Kick

* * *

197 198 199 200

214 215 216 217

167

Appendices

Patch List
USER (User Group)
No. Name 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 049 050 051 052 053 054 055 056 057 058 059 060 061 062 063 064 Voice Key Assign POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY SOLO POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY SOLO POLY SOLO POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY No. Name 065 066 067 068 069 070 071 072 073 074 075 076 077 078 079 080 081 082 083 084 085 086 087 088 089 090 091 092 093 094 095 096 097 098 099 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 Voice Key Assign POLY POLY POLY POLY SOLO POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY SOLO POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY SOLO POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY SOLO POLY POLY POLY POLY POLY POLY Temple of XP 4 Power Split 4 Symphonique2 4 Robot Voice 4 St.Concert 4 ViennaStrgs2 4 R&R Brass 3 Disto Stack 4 Tone Wh.Solo 3 Combing Slow 3 SessionNyln2 3 Celestial 2 4 Poly Brs 4 DanceStack 1 3 303 Ow Bass 1 Flying Waltz 4 Silky Way 2 Simply June 1 Solo Vln 1 / 4 Super Tenor 3 Metal Solo 4 Creator 3 Amsterdamer 2 Techno Pizz 1 SA Rhodes 3 3 Dim Hit 1 4 Pan Pipes 2 JP-8 Str 1 2 Pretty Bells 2 Aurora 4 Breathy Humz 2 Full Orch.2 4 Clean Tele 4 Dunes 4 Cyber-Trance 3 RiversOfTime 4 F.Hrn Sect5/ 3 DreamVoices2 2 HeavenlyPad 2 Sop.Sax mf 2 Sweep Clav 2 3 Cold JX 1 Solo Vc 1 / 3 RichStrings2 4 Techno Dream 3 StateXLChord 4 Delicate EP 2 Bassic Needs 2 Perky B 2 SquareLead 2 2 Earth Blow 2 BassMarimba1 2 Morning Lite 2 Raggatronic 4 Brass ff 1 2 Acc.de Paris 2 Oboe 1 2 Velo Power 4 Vintage Call 4 Steel Away 3 Spectrum Mod 4 Raverborg 4 Poly Saws 4 Adrenaline 4 Heirborne 4 Trumpet 2 Glistening 4 Banded Jupe 1 SingingMini 1 Chamber Ens2 2 DanceStack 5 4 SA Rhodes 4 4 Breathy Brs 3 Atmos Harp 4 303 Bass 2 Flute 1 Perc Hit 2 / 4 Oldies Organ 2 Dulcimer 2 Warmer Pad 2 2 ARPsychea 4 Choir 1 3 Agitato Str2 4 Pure Tibet 1 Flugelhorn 1 2 D-50 Stack 4 Noiz Mania 4 Slap Bass 2 1 Amazing Echo 4 Moving Glass 1 BluesHarp 1 Tria Bells 4 DirtyOrgan 2 2 Dawn 2 Dusk 3 Just Lovely 1 SquareKeys 2 1 Natural Vlns 2 Arasian Morn 4 Euro-Dance 2 3 5th Pad 4 Liquid Sky 4 Sci-Fi Bells 3 Nomad Perc 3 Orn.Recorder 3 FXM Saw Lead 4 Atlantis 2 4 Taj Mahal 1 X-hale 4 Stacc.Heaven 4 Altamira 2 Hit House 4 Solo F.Horn1 1 Celesta 1 1 ORBit Pad 2 SessionBrass 4 Sugar Bell 4 ChristmasFlt 2 Strobe Mode 4 Cave 4 TenorExprss2 2 Impact 4 X-Tronic Jam 4 WarmViolins2 4 Rain Forest 4 Brass Ens 4 3 Perelandra 4 Teknoperator 4 Crowds 4

PR-A (Preset A Group)


No. Name 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 049 050 051 052 053 054 055 056 057 058 059 060 061 062 063 064 Voice Key Assign POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY No. Name 065 066 067 068 069 070 071 072 073 074 075 076 077 078 079 080 081 082 083 084 085 086 087 088 089 090 091 092 093 094 095 096 097 098 099 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 Voice Key Assign POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY SOLO SOLO 64voicePiano 1 Bright Piano 1 Classique 2 Nice Piano 3 Piano Thang 3 Power Grand 3 House Piano 2 E.Grand 1 MIDIed Grand 3 Piano Blend 3 West Coast 4 PianoStrings 4 Bs/Pno+Brs 4 Waterhodes 2 S.A.E.P. 3 SA Rhodes 1 4 SA Rhodes 2 2 Stiky Rhodes 3 Dig Rhodes 2 Nylon EPiano 4 Nylon Rhodes 4 Rhodes Mix 3 PsychoRhodes 2 Tremo Rhodes 4 MK-80 Rhodes 1 MK-80 Phaser 1 Delicate EP 2 Octa Rhodes1 4 Octa Rhodes2 4 JV Rhodes+ 4 EP+Mod Pad 4 Mr.Mellow 4 Comp Clav 1 Klavinet 4 Winger Clav 4 Phaze Clav 1 2 Phaze Clav 2 1 Phuzz Clav 2 Chorus Clav 1 Claviduck 2 Velo-Rez Clv 1 Clavicembalo 4 Analog Clav1 1 Analog Clav2 1 Metal Clav 3 Full Stops 2 Ballad B 3 Mellow Bars 4 AugerMentive 3 Perky B 2 The Big Spin 3 Gospel Spin 3 Roller Spin 3 Rocker Spin 3 Tone Wh.Solo 3 Purple Spin 4 60s LeadORG 2 Assalt Organ 3 D-50 Organ 2 Cathedral 4 Church Pipes 4 Poly Key 3 Poly Saws 4 Poly Pulse 4 Dual Profs 3 Saw Mass 4 Poly Split 4 Poly Brass 3 Stackoid 4 Poly Rock 4 D-50 Stack 4 Fantasia JV 4 Jimmee Dee 4 Heavenals 4 Mallet Pad 4 Huff N Stuff 3 Puff 1080 2 BellVox 1080 4 Fantasy Vox 4 Square Keys 2 Childlike 4 Music Box 3 Toy Box 2 Wave Bells 4 Tria Bells 4 Beauty Bells 4 Music Bells 2 Pretty Bells 2 Pulse Key 3 Wide Tubular 4 AmbienceVibe 4 Warm Vibes 2 Dyna Marimba 1 Bass Marimba 4 Nomad Perc 3 Ethno Metals 4 Islands Mlt 4 Steelin Keys 3 Steel Drums 1 Voicey Pizz 3 Sitar 2 Drone Split 4 Ethnopluck 4 Jamisen 2 Dulcimer 2 East Melody 2 MandolinTrem 4 Nylon Gtr 1 Gtr Strings 3 Steel Away 3 Heavenly Gtr 4 12str Gtr 1 2 12str Gtr 2 3 Jz Gtr Hall 1 LetterFrmPat 4 Jazz Scat 3 Lounge Gig 3 JC Strat 1 Twin Strats 3 JV Strat 2 Syn Strat 2 Rotary Gtr 2 Muted Gtr 1 SwitchOnMute 2 Power Trip 2 Crunch Split 4 Rezodrive 2 RockYurSocks 4

Voice: number of voice

168

Patch List

PR-B (Preset B Group)


No. Name 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 049 050 051 052 053 054 055 056 057 058 059 060 061 062 063 064 Voice Key Assign POLY POLY POLY SOLO POLY POLY POLY POLY SOLO POLY SOLO SOLO SOLO POLY SOLO SOLO POLY POLY SOLO SOLO POLY SOLO SOLO SOLO SOLO SOLO POLY SOLO SOLO POLY POLY SOLO POLY SOLO SOLO SOLO SOLO SOLO SOLO POLY SOLO POLY POLY SOLO SOLO SOLO SOLO SOLO POLY SOLO POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY No. Name 065 066 067 068 069 070 071 072 073 074 075 076 077 078 079 080 081 082 083 084 085 086 087 088 089 090 091 092 093 094 095 096 097 098 099 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 Voice Key Assign POLY POLY POLY POLY SOLO POLY POLY POLY POLY POLY POLY POLY POLY POLY SOLO POLY POLY SOLO SOLO SOLO SOLO SOLO SOLO SOLO POLY SOLO SOLO SOLO SOLO SOLO POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY SOLO POLY POLY POLY POLY Dist Gtr 1 3 Dist Gtr 2 3 R&R Chunk 4 Phripphuzz 1 Grungeroni 3 Black Widow 4 Velo-Wah Gtr 1 Mod-Wah Gtr 2 Pick Bass 1 Hip Bass 2 Perc.Bass 3 Homey Bass 2 Finger Bass 1 Nylon Bass 2 Ac.Upright 1 Wet Fretls 1 Fretls Dry 2 Slap Bass 1 2 Slap Bass 2 1 Slap Bass 3 1 Slap Bass 4 2 4 Pole Bass 1 Tick Bass 4 House Bass 3 Mondo Bass 3 Clk AnalogBs 2 Bass In Face 2 101 Bass 2 Noiz Bass 2 Super Jup Bs 2 Occitan Bass 3 Hugo Bass 4 Multi Bass 2 Moist Bass 2 BritelowBass 4 Untamed Bass 3 Rubber Bass 3 Stereoww Bs 3 Wonder Bass 3 Deep Bass 2 Super JX Bs 2 W<RED>-Bass 4 HI-Ring Bass 3 Euro Bass 2 SinusoidRave 1 Alternative 2 Acid Line 1 Auto TB-303 3 Hihat Tekno 2 Velo Tekno 1 3 Raggatronic 4 Blade Racer 4 S&H Pad 1 Syncrosonix 3 Fooled Again 1 Alive 3 Velo Tekno 2 2 Rezoid 4 Raverborg 4 Blow Hit 4 Hammer Bell 3 Seq Mallet 2 Intentions 3 Pick It 3 Analog Seq 2 Impact Vox 4 TeknoSoloVox 2 X-Mod Man 2 Paz <==> Zap 1 4 Hits 4 You 4 Impact 4 Phase Hit 3 Tekno Hit 1 2 Tekno Hit 2 2 Tekno Hit 3 4 Reverse Hit 3 SquareLead 1 3 SquareLead 2 2 You and Luck 2 Belly Lead 4 WhistlinAtom 2 Edye Boost 2 MG Solo 4 FXM Saw Lead 4 Sawteeth 3 Smoothe 2 MG Lead 2 MG Interval 4 Pulse Lead 1 3 Pulse Lead 2 4 Little Devil 4 Loud SynLead 4 Analog Lead 2 5th Lead 2 Flute 2 Piccolo 1 VOX Flute 4 Air Lead 2 Pan Pipes 2 Airplaaane 4 Taj Mahal 1 Raya Shaku 3 Oboe mf 1 Oboe Express 2 Clarinet mp 1 ClariExpress 2 Mitzva Split 4 ChamberWinds4 ChamberWoods3 Film Orch 4 Sop.Sax mf 2 Alto Sax 3 AltoLead Sax 3 Tenor Sax 3 Baritone Sax 3 Take A Tenor 4 Sax Section 4 Bigband Sax 4 Harmonica 2 Harmo Blues 2 BluesHarp 1 Hillbillys 4 French Bags 4 Majestic Tpt 1 Voluntare 2 2Trumpets 2 Tpt Sect 4 Mute TP mod 4

PR-C (Preset C Group)


No. Name 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 049 050 051 052 053 054 055 056 057 058 059 060 061 062 063 064 Voice Key Assign POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY No. Name 065 066 067 068 069 070 071 072 073 074 075 076 077 078 079 080 081 082 083 084 085 086 087 088 089 090 091 092 093 094 095 096 097 098 099 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 Voice Key Assign POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY Harmon Mute 1 Tp&Sax Sect 4 Sax+Tp+Tb 3 Brass Sect 4 Trombone 1 Hybrid Bones 4 Noble Horns 4 Massed Horns 3 Horn Swell 4 Brass It! 4 Brass Attack 3 Archimede 3 Rugby Horn 3 MKS-80 Brass 2 True ANALOG 2 Dark Vox 2 RandomVowels 4 Angels Sing 2 Pvox Oooze 3 Longing... 3 Arasian Morn 4 Beauty Vox 3 Mary-AnneVox 4 Belltree Vox 4 Vox Panner 2 Spaced Voxx 4 Glass Voices 3 Tubular Vox 4 Velo Voxx 2 Wavox 3 Doos 1 Synvox Comps 4 Vocal Oohz 3 LFO Vox 1 St.Strings 2 Warm Strings 4 Somber Str 4 Marcato 2 Bright Str 2 String Ens 4 TremoloStrng 2 Chambers 3 ViolinCello 4 Symphonique 4 Film Octaves 4 Film Layers 4 Bass Pizz 4 Real Pizz 3 Harp On It 3 Harp 2 JP-8 Str 1 2 JP-8 Str 2 3 E-Motion Pad 4 JP-8 Str 3 4 Vintage Orch 4 JUNO Strings 3 Gigantalog 4 PWM Strings 3 Warmth 2 ORBit Pad 2 Deep Strings 2 Pulsify 4 Pulse Pad 4 Greek Power 4 Harmonicum 2 D-50 Heaven 2 Afro Horns 3 Pop Pad 4 Dreamesque 4 Square Pad 4 JP-8 Hollow 4 JP-8Haunting 4 Heirborne 4 Hush Pad 4 Jet Pad 1 2 Jet Pad 2 2 Phaze Pad 3 Phaze Str 4 Jet Str Ens 2 Pivotal Pad 4 3D Flanged 1 Fantawine 4 Glassy Pad 3 Moving Glass 1 Glasswaves 3 Shiny Pad 4 ShiftedGlass 2 Chime Pad 3 Spin Pad 2 Rotary Pad 4 Dawn 2 Dusk 3 Aurora 4 Strobe Mode 4 Albion 2 Running Pad 4 Stepped Pad 4 Random Pad 4 SoundtrkDANC 4 Flying Waltz 4 Vanishing 1 5th Sweep 4 Phazweep 4 Big BPF 4 MG Sweep 4 CeremonyTimp 3 Dyno Toms 4 Sands ofTime 4 Inertia 4 Vektogram 4 Crash Pad 4 Feedback VOX4 Cascade 1 Shattered 2 NextFrontier 2 Pure Tibet 1 Chime Wash 4 Night Shade 4 Tortured 4 Dissimilate 4 Dunes 4 Ocean Floor 1 Cyber Space 3 Biosphere 2 Variable Run 4 Ice Hall 2 ComputerRoom 4 Inverted 4 Terminate 3

Voice: number of voice

169

Appendices

Patch List

PR-D (GM Group)


No. Name 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 049 050 051 052 053 054 055 056 057 058 059 060 061 062 063 064 Voice Key Assign 2 2 2 2 2 4 1 2 1 2 1 1 1 2 2 2 1 1 2 2 1 1 1 2 1 1 1 1 1 1 1 3 3 1 1 1 1 2 1 1 1 2 2 2 1 1 1 2 2 1 2 2 1 1 1 2 1 2 2 1 2 1 1 2 POLY *1 POLY *2 POLY POLY POLY POLY POLY *2 POLY POLY *2 POLY *2 POLY POLY POLY *2 POLY *2 POLY *2 POLY POLY POLY POLY POLY POLY POLY *1 POLY POLY POLY *1 POLY POLY POLY *1 POLY POLY POLY *1 POLY POLY POLY POLY *1 POLY POLY POLY POLY POLY POLY *2 POLY *2 POLY *2 POLY *2 POLY POLY *2 POLY *2 POLY *2 POLY POLY POLY POLY POLY *1 POLY POLY POLY *2 POLY *1 POLY *2 POLY *2 POLY *2 POLY *2 POLY *2 POLY POLY No. Name 065 066 067 068 069 070 071 072 073 074 075 076 077 078 079 080 081 082 083 084 085 086 087 088 089 090 091 092 093 094 095 096 097 098 099 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 Voice Key Assign 1 1 1 2 1 1 2 1 1 1 2 2 2 1 1 2 2 2 2 2 3 2 3 2 3 2 2 2 3 2 3 2 2 2 2 2 3 2 2 2 1 1 2 1 1 3 1 1 4 1 1 1 4 2 2 1 1 2 3 4 1 2 4 2 POLY POLY POLY *1 POLY POLY *2 POLY *2 POLY *2 POLY POLY *2 POLY POLY *2 POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY *2 POLY POLY POLY POLY POLY POLY POLY POLY Piano 1 Piano 2 Piano 3 Honky-tonk E.Piano 1 E.Piano 2 Harpsichord Clav. Celesta Glockenspiel Music Box Vibraphone Marimba Xylophone Tubular-bell Santur Organ 1 Organ 2 Organ 3 Church Org.1 Reed Organ Accordion Fr Harmonica Bandoneon Nylon-str.Gt Steel-str.Gt Jazz Gt. Clean Gt. Muted Gt. Overdrive Gt DistortionGt Gt.Harmonics Acoustic Bs. Fingered Bs. Picked Bs. Fretless Bs. Slap Bass 1 Slap Bass 2 Synth Bass 1 Synth Bass 2 Violin Viola Cello Contrabass Tremolo Str PizzicatoStr Harp Timpani Strings Slow Strings Syn.Strings1 Syn.Strings2 Choir Aahs Voice Oohs SynVox OrchestraHit Trumpet Trombone Tuba MutedTrumpet French Horn Brass 1 Synth Brass1 Synth Brass2 Soprano Sax Alto Sax Tenor Sax Baritone Sax Oboe English Horn Bassoon Clarinet Piccolo Flute Recorder Pan Flute Bottle Blow Shakuhachi Whistle Ocarina Square Wave Saw Wave Syn.Calliope Chiffer Lead Charang Solo Vox 5th Saw Wave Bass & Lead Fantasia Warm Pad Polysynth Space Voice Bowed Glass Metal Pad Halo Pad Sweep Pad Ice Rain Soundtrack Crystal Atmosphere Brightness Goblin Echo Drops Star Theme Sitar Banjo Shamisen Koto Kalimba Bag Pipe Fiddle Shanai Tinkle Bell Agogo Steel Drums Woodblock Taiko Melo. Tom 1 Synth Drum Reverse Cym. Gt.FretNoise Breath Noise Seashore Bird Telephone 1 Helicopter Applause Gun Shot

PR-E (Preset E Group)


No. Name 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 049 050 051 052 053 054 055 056 057 058 059 060 061 062 063 064 Voice Key Assign POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY SOLO SOLO SOLO POLY POLY SOLO POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY No. Name 065 066 067 068 069 070 071 072 073 074 075 076 077 078 079 080 081 082 083 084 085 086 087 088 089 090 091 092 093 094 095 096 097 098 099 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 Voice Key Assign POLY SOLO SOLO POLY POLY SOLO POLY POLY POLY POLY SOLO POLY SOLO POLY POLY POLY POLY POLY POLY SOLO POLY SOLO POLY POLY SOLO POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY POLY SOLO POLY POLY POLY POLY Echo Piano 3 Upright Pno 3 RD-1000 3 Players EP 2 D-50 Rhodes 4 Innocent EP 2 Echo Rhodes 4 See-Thru EP 3 FM BellPiano 3 Ring E.Piano 4 Soap Opera 1 Dirty Organ 3 Surfs Up! 2 Organesque 3 pp Harmonium 1 PieceOfCheez 1 Harpsy Clav 2 Exotic Velo 4 HolidayCheer 4 Morning Lite 2 Prefab Chime 3 Belfry Chime 3 Stacc.Heaven 4 2.2 Bell Pad 4 Far East 4 Wire Pad 3 PhaseBlipper 2 Sweep Clav 3 Glider 2 Solo Steel 4 DesertCrystl 4 Clear Guitar 3 Solo Strat 3 Feed Me! 4 Tube Smoke 2 Creamy 2 Blusey OD 2 Grindstone 2 OD 5ths 3 East Europe 2 Dulcitar 4 Atmos Harp 4 Pilgrimage 4 202 Rude Bs 2 2pole Bass 2 4pole Bass 2 Phaser MC 2 Miniphaser 2 Acid TB 1 Full Orchest 4 Str + Winds 4 Flute 2080 2 Scat Flute 2 Sax Choir 4 Ballad Trump 4 Sm.Brass Grp 4 Royale 4 Brass Mutes 2 Breathy Brs 3 3 Osc Brass 3 P5 Polymod 2 Triumph Brs 3 Techno Dream 3 Organizer 3 Civilization 3 Mental Chord 4 House Chord 4 Sequalog 4 Booster Bips 2 VintagePlunk 4 Plik-Plok 2 RingSequence 4 Cyber Swing 4 Keep :-) 2 Resojuice 2 Bon dmoov! 3 Dist TB-303 2 Temple of JV 4 Planet Asia 4 Afterlife 3 Trancing Pad 2 Pulsatronic 3 Cyber Dreams 3 Warm Pipe 1 Pure Pipe 2 SH-2000 2 X..? Whistle 3 Jay Vee Solo 3 Progresso Ld 4 Adrenaline 4 Enlighten 4 Glass Blower 3 Earth Blow 2 JX SqrCarpet 2 Dimensional 2 Jupiterings 2 Analog Drama 3 Rich Dynapad 4 Silky Way 2 Gluey Pad 3 BandPass Mod 2 Soundtraque 2 Translucence 4 Darkshine 4 Dlight 2 December Sky 4 Octapad 3 JUNO Power! 4 Spectrum Mod 4 Stringsheen 3 GR500 TmpDly 2 Mod DirtyWav 3 Silicon Str 4 D50FantaPerc 3 Rotodreams 3 Blue Notes 4 RiversOfTime 4 Phobos 2 2 0 8 0 4 Unearthly 4 Glistening 4 Sci-Fi Str 3 Shadows 4 Helium Queen 4 Sci-Fi FX x4 1 Perky Noize 3 Droplet 3 Rain Forest 4

*1: Uses XP-A (Session) waves. *2: Uses XP-B (Orchestral) waves.

Voice: number of voice

170

Patch List

XP-A (WAVE EXPANSION A: Session)


No. 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 049 050 051 052 053 054 055 056 057 058 059 060 061 062 063 064 Name St.Concert 9ft.Grand 1 9ft.Grand 2 Euro Classic St.Pno & Str Compress Pno LA Session Water Piano Vibra Rhodes Stack Rhodes ArcoEnsemble Vienna Strgs Str Adagio Oct Strings Silky Filter Soft Strings SlowStr.Sect GiantStrings Str+Choir 1 Str+Choir 2 Str+Choir 3 Breathy Humz Dream Voices Mmmms Chorale Space Men Choir Mm+Aah Ivory Mist PercussiVox Mysteriouso Phase Mmhs AmbientStory Venus SessionBrass Port.Tpts R&R Brass Echo Brass E.Coast Brs Bop Soli Soft Saxes Orchestral Octalog Hrn Tpt Soloist Legato Tpt Dyno Trumpet Ethno-Trumps Super Tenor TenorExpress T.Sax f Legato Flute Touch Flute NewAge Flute Flute inMist Hybrid Flute Flute & Cla ChristmasFlt Fifth Flute Cosmic Flute Acc.de Paris Paris 50s Musette Ens Montmartre Sad Akordion Fr.Accordion Voice 4 4 4 2 4 1 4 4 3 4 2 3 2 3 2 2 2 4 4 4 4 2 2 2 1 3 4 4 4 3 3 4 3 4 2 3 4 4 2 4 4 2 1 2 2 2 3 2 1 2 2 1 2 2 3 2 2 2 2 4 4 2 3 1 No. 065 066 067 068 069 070 071 072 073 074 075 076 077 078 079 080 081 082 083 084 085 086 087 088 089 090 091 092 093 094 095 096 097 098 099 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 Name Fr.Accord 2 Troubadour SessionNylon Solo Nylon 1 Solo Nylon 2 Nylon & Str Nylon & Flt Nylon Chord Stratar Clean Tele Nashville Super Trem SpaghettiGtr DuannesTone Big Hair Ld Metal Solo Crunch Tone Overdriven Blues Tele Tube Double Neils Rust Short Crunch X-Fade Metal Velo Power Phazy Chunk Reso Tele Wah Wah BPM Rock P.Bass1 Rock P.Bass2 Rock P.Bass3 Big Jazz Bs BriteJazz Bs Ch.Jazz Bs Mellow Jz Bs Mute E.Bs Octabahn Bs Slobbery Bs Phase Worm Euro Rave Bs Pumpin Bs Tech NoBase Bad Acid Bs CheepEcho Bs Manic Bs JP6 Sqr Key Square drops Celestial Heavenly Eko JD-800 Nomad Vibrolater MartianChime Big Wet Blip Amazing Echo DelaySession Deletex Tarlia Mahoroba Eurotek Clav Dope Resoclv Tekno Juno Buzzzzzzzzzz Slop-a-rama Isnt Pretty Polywasp Voice 2 3 3 3 2 4 3 3 2 4 1 4 2 2 2 4 1 1 4 2 4 4 4 4 4 1 4 1 2 4 3 1 2 2 1 4 2 2 2 3 2 2 3 4 2 1 3 4 3 4 4 4 4 4 4 3 4 2 1 2 2 2 3 1 No. 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 Name Quixelate Trangoa Wave Spiked Cheez Glassy Cheez Super 808Cow Arpeggiatoid Euro Hit 1 Euro Hit 2 Rave Slice Str Torture Juno Harpsi Big Mess Pad Harpsichoir Echo Juno Phazerave DanceStack 1 DanceStack 2 DanceStack 3 DanceStack 4 DanceStack 5 DanceStack 6 DanceStack 7 DanceStack 8 Eurotek Brs Synergy Brs PortaSynthex Razor VCOs Big PWM Flutey Stack Wobbly 5th Tekno Square Trance VoXxX Random Rave Raver Circus Resorave Flangomatic O-Zu-Nu Sub Divided Ancient Sqr Fat Flange Phaze NRG Phase Vox Systekno On the move! XPration Big Ensemble Lazerette Fazed String Combing Slow Jet Stack Phazeslopad Rize Mass Portent DCO Sweeper Sweep Rain Sweep Stack Big Vectors Poly Swell Alchemy Soli-na 90s Str Mach Ultra Cheez Juno-60 Pad Progressive Voice 4 2 3 3 4 4 4 2 1 2 3 4 4 3 2 3 4 4 3 4 3 4 4 4 4 3 4 2 2 4 3 4 3 4 2 2 4 1 2 2 1 3 4 2 2 4 3 4 3 4 4 3 2 3 4 3 4 2 3 2 4 2 3 2 No. 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 Name Build-Up Syn Atlantis 2 Perelandra Plutonium Nautilus Metal Dreams Glass Clouds Harmonicloud Shining Veil Ethereal JX Striking 5th Meow 5ths Stepflanger Happy LFOs Aero Insect Beat Sweeper Wormy Lead Atmo Lead Caliolead Tweedles Raw PWM Voc Solo 5th Dirty Lead Boostweeper1 Boostweeper2 B3 Filth Phazed Organ VSw Vibrafon SA Vibe Rich Vibes SpaceGamelan Toy Vibe Analog Bomb Seashore 2 Creation Cyberjunkie Sci-Fi Bells Shine on DEMO Piano1 DEMO Piano2 DEMO PnoVox DEMO Str 1 DEMO Str 2 DEMO Str 3 DEMO SynPuls DEMO 5thPad DEMO Choir DEMO Brass DEMO Tenor DEMO Tpt DEMO Flute DEMO Nylon DEMO PhaseGt DEMO DistGt1 DEMO DistGt2 DEMO Strat DEMO SlapBs DEMO P.Bass DEMO SynBs DEMO SynLead DEMO Insect DEMO Buzzzzz DEMO Crowd Voice 3 4 4 4 2 2 4 4 3 2 4 2 3 4 3 2 3 3 3 2 2 4 2 2 2 4 3 3 1 2 4 3 2 4 4 4 3 1 4 4 3 2 2 2 2 4 2 1 3 1 2 4 4 4 3 3 2 1 2 4 4 2 4

Voice: number of voice

171

Appendices

Patch List

XP-B (WAVE EXPANSION B: Orchestral)


No. 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 049 050 051 052 053 054 055 056 057 058 059 060 061 062 063 064 Name Warm Violins Slow Vlns 1 Vlns+Vlas 1 Vl Sect mono Arco Violins Marcato Vls1 Vlns+Vlas 2 Agitato Vls1 Rosin Pad 1 Dry Mid-High Natural Vlns Sad Vln Sect Marcato Vas Arco Violas Thick Violas Va Sect f Va Small Sec Agitato Vas1 Sad Violas Fast Cellos1 Vcs Legato 1 Marcato Vcs1 Small Vc Sec Agitato Vcs1 Small Cellos Sad CelloSec Cb Sect ff Wide Basses mf Basses Agitato Cbs1 Vcs+Cbs 2 Basses Euro Strings Rich Strings Multi Strs 1 VlsVasVcsCbs Bright Strs Classicl Str Full Strings Med Str Sec Small Strngs Strings Arco Vivace Strs Agitato STR1 LowSTR Attak Bad Guy STR Ominous Lo Express DramaStrings Solo Vln 1 / Solo Vln 2 Chorus Vln Stereo Vln Agitato Vln1 Solo Vla 1 / Solo Vla 2 Chorus Viola Stereo Viola Agitato Vla Solo Vc 1 / Solo Vc 2 Stereo Cello Chorus Cello Marcato Vc 1 Voice 3 3 4 2 4 4 2 4 2 4 2 2 2 2 2 1 3 4 2 4 1 3 2 4 1 2 4 2 1 4 2 2 4 4 2 4 4 3 4 2 1 4 4 4 4 3 4 4 4 4 2 2 3 2 3 2 2 3 2 3 2 3 2 1 No. 065 066 067 068 069 070 071 072 073 074 075 076 077 078 079 080 081 082 083 084 085 086 087 088 089 090 091 092 093 094 095 096 097 098 099 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 Name Solo Cb 1 / Solo Cb 2 Marcato Cb 1 Chamber Ens1 Chamber Ens2 Vln+Vla Dble Vln+Vc Dbl1 Vla+Vc Dbl2 Vla+Vc Dble Pizzicato 1 Mono Pizz Pizzicato 2 Room Pizz Hall Pizz Tight Pizz Short Pizz STR Marcato1 Oct Marcato Lower Marc!! Big Marc! STR Spiccato Fast Attacks Flute Flute V-Sw Piccolo Piccolo Flt Recorder Oboe 1 Oboe 2 Oboe 3 Oboe 4 Oboe 5 English Hrn1 English Hrn2 English Hrn3 Bassoon 1 Bassoon 2 Clarinet 1 Clarinet 2 Bs Clarinet1 Bs Clarinet2 Trumpet 1 Trumpet 2 Trumpet 3 Flugelhorn 1 Flugelhorn 2 Cornet 1 Cornet 2 Solo Tb 1 Solo Tb 2 Solo Tb 3 / Solo Tb 4 / Bs Tb 1 Bs Tb 2 / Harmon Mute1 Harmon Mute2 Tuba 1 Tuba 2 Solo F.Horn1 Solo F.Horn2 Sml F.Hrn sc Horn Sect 1/ F.Horn sc x4 Fr.Horn sfz Voice 3 2 1 1 2 2 2 2 2 3 1 2 1 4 3 2 2 4 4 4 3 4 1 4 1 2 1 2 2 2 2 2 1 1 1 1 1 1 2 2 2 1 3 2 2 1 1 2 1 1 4 2 1 2 1 2 2 2 1 1 3 4 1 2 No. 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 Name F.Hrn Sect2/ F.Hrn Sect3 F.Hrn Sect4 F.Hrn Sect5/ F.Hrn Sect6 F.Hrn Sect7 F.Hrn Sect8 MuteHrn Sect Horn+Wood 1 Horn+Wood 2 Horn+Wood 3 Wood Sect 1 Wood Sect 2 Wood Sect 3 Wood Sect 4 2 Oboes Oboe + Cla Flt + Piccl Flute + Cla Bassoon+EHrn Hi Woodwinds WoodwindSplt Multi Reed 4Trombones Tb Sect 1 Tb + Tp 4Trumpets 3 Trumpets Brass ff 1 Brass ff 2 Brass ff 3 McArthur Brs Big Bones BassBoneSect Brass Swell1 Full Brs 1 Brass Sect1/ Brass Ens 1 Brass Ens 2 Brass Ens 3 Brass Ens 4 Brass Ens 5 Brass Ens 6 Brass Ens 7 Brass Ens 8 Horn Strings Full Orch.1 Full Orch.2 Full Orch.3 Full Orch.4 Maj Hit 1 Min Hit 1 Dim Hit 1 Major Stab! Maj Hit 2 Min Hit 2 Classical Gt Harp 1 Harp 2 Plucked Harp Harp StrumMj Harp StrumMn Water Harp ClasclPiano1 Voice 2 2 4 3 2 4 2 1 4 4 3 3 4 3 3 2 2 2 2 3 4 2 1 2 3 2 4 3 2 3 4 4 4 3 3 4 4 3 3 3 3 3 3 3 3 4 2 4 4 4 4 4 4 4 4 4 3 1 2 3 4 4 3 2 No. 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 Name ClasclPiano2 ClasclPiano3 ClasclPiano4 Harpsichord1 Harpsichord2 Harpsichord3 Harpsichord4 Celesta 1 Celesta 2 Celesta 3 Glockenleste Marimba BassMarimba1 BassMarimba2 Vibe Xylophone 1 Xylophone 2 Xylophone 3 Glocken 1 Glocken 2 ChurchBells1 ChurchBells2 ChurchBells3 TubulaBells1 TubulaBells2 Big Tubulars Dawning MalletStack1 MalletStack2 MalletStack3 MalletStack4 MalletStack5 MalletStack6 MalletStack7 Choir 1 Choir 2 Snare Drum ConcertSNR1/ ConcertSNR2/ SNR Roll / Concert BD1 Concert BD2/ BD Roll / Timpani 1 / Timpani 2 / Timpani 3 Timpani 4 / Tam Tam Gong Piatti!! Sleigh Bells Slapstick / Wind Chimes1 Wind Chimes2 Tambourine / Castanets / Rhythm Set Perc Hit 1 Perc Hit 2 / Perc Hit 3 Presenting! Presto! Christmas!!! Voice 3 2 2 2 3 4 3 1 2 1 2 1 2 1 1 2 3 1 1 1 3 4 3 2 2 4 4 4 3 4 4 4 4 4 3 1 2 4 3 4 3 3 3 2 4 4 3 2 2 2 1 3 1 3 2 2 3 4 4 3 4 4 3

Voice: number of voice

172

Patch List

XP-C (WAVE EXPANSION C: Techno Collection)


No. 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 049 050 051 052 053 054 055 056 057 058 059 060 061 062 063 064 Name Teknoperator(132) Transmission(144) X-Tronic Jam(120) Dirt Jungle(160) DJ Spinnin(151) Zipper Beat(151) Tribal House(151) Obsession(144) Sonic Empire(144) Double Dutch(140) E-tronicBoom(116) Chillout =->(116) MecaTrip-Hop( 90) Hero Beat( 90) Hit House(120) Voco Groove(122) Hell Fire(151) Lo:BD Hi:HH(144) Detroit+Perc(132) Crossfader(120) Soft & Hard(120) Space Shake(130) Under Ether( 85) Confusion(147) Amsterdamer(184) House that?(120) Phrase Menu Cyber-Trance Creator Etherality Unplugged Acid Melt Brain Waves 1Shot Groove FirstContact Ambient S/H Deep Machine Big Blue TeeBee V/Sw 303 Agressor TB or not TB HiLo303ModSw 2Square Bass 303 HollowBS 303 Bass TB Saw Bass 303 Ow Bass TB Square 1 TB Square 2 TB Square 3 Solid Bass 1 Solid Bass 2 FM Tube Bass DrumnBass Sub Bass Dirty Bass Gate Me Buzz Comprex Bass Bass Invader Ovdrive Bass Housy Bella Bassic Needs Raver Bass 1 Raver Bass 2 Voice 4 4 4 2 4 4 3 4 4 4 3 4 4 4 4 4 4 2 2 2 2 4 2 4 2 4 1 3 3 4 4 3 4 1 2 4 2 2 4 2 3 2 2 2 2 1 1 2 2 2 2 1 3 3 1 2 1 1 2 1 4 2 2 2 No. 065 066 067 068 069 070 071 072 073 074 075 076 077 078 079 080 081 082 083 084 085 086 087 088 089 090 091 092 093 094 095 096 097 098 099 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 Name Jericho Bass Slippy Bass Rise Bass Cyber Bass SH-2000 Bass FM Bass Razor Bass SquelchyBass RaversBass Compu Bass Jump Bass VocoBass Vocoder Menu 1.2.3.4. BPM TeknoMusic Retrocoder u/i/e/o V/Sw Talk Box 1 Talk Box 2 VT Vox Artificial BariVoise After D ! ARPsychea Vintage Call HarmoChimer Ring Bell 260 & JUNO 260 MIDI SquareKeys 2 Pure Sine Ambient ORG JX Planet Clavi-Club Sweep Clav 2 SquareTek Retro Party Rave Nature Alias Square Dirty Stack Phenomena Music Hi Euro-Dance 1 Euro-Dance 2 Dance Stack Raver Blade White Gloves Touchdown Rave Station Time Warp Thin Rave Igor Circus Alpha Zone Stars March JP Velo-Saw Rich Teeth After Saw Saw Cocktail Poly Message Xpressive Earblower Cutting Edge Stalactica LA Heaven Voice 2 2 2 2 2 1 2 2 4 2 2 2 1 4 3 2 4 3 1 2 4 1 4 4 4 2 2 3 1 1 1 2 1 2 3 2 3 2 2 1 4 1 3 3 4 4 1 4 2 3 4 3 4 4 2 4 4 3 2 4 3 4 4 4 No. 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 Name Euforia Labo-Feedbak Banded Jupe Killer Pad Mystic Pad D-Mention X-hale Sirena Afters Pad Warmer Pad Phatt Pad OB Sweep Pad Murk Pad Dense Floor SecretMelody Vaporish Vintage Revo Liquid Sky Exploration Drama Pad Vapor Style JP-6 Stack Obilator Glamour Medium Solo SingingMini Analog Flute SH-5 Bs/Lead Classy Pulse Jupiter-6 Ld Just Lovely DJ Devil Simply June Mr.Raw SAW Crispy Lead Dirty Lead 2 Disto Stack Velo Cheese Noiz Mania Power Mutes V-Beep Freaky Fry SQ Formule DirtyOrgan 2 Oldies Organ Edgy Organ Juno Organ Space Org X Cabin Organ Dream Organ Club Organ Perc. Organ Organ Stabs Techno Pizz Captain Pizz Pizzatek Sleepless Mega 5th 2 Chord maj7th Chord min7th 5thDimension StateXLChord Sixth Sense Garage Chord Voice 3 4 1 1 4 4 4 4 3 2 2 3 4 4 4 4 3 4 3 4 4 1 1 3 3 1 1 2 1 2 1 1 1 1 4 3 4 3 4 2 1 1 1 2 2 4 2 3 2 3 2 2 2 1 4 2 4 2 4 4 4 4 4 4 No. 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 Name Chordmaj7/5Planet EKNO Optimum Rave Arpege Me VTransformer Analog Attax Maxi Fuzzy ! Only by FXM Hit & Run Photon Attak Predator Village Hit Hardcore Hit Short Chord ShortCircuit SonofaPitch Flutish SQUR FazzyCow 808 Blurpy Static Hit Hi Attack TonalTension Jungle Stabs Buzz Machine Zapper Blip Iron Hit Headz Direct Scratchy Hit Hit&IndsMenu GTR FX Menu GTR Power 1 GTR Power 2 Snr Menu 1 Snr Menu 2 Kick Menu Hi Hat Menu Perc Menu Tom&Cym Menu Metal Dream System D Mayday Ring Industrial Tranceporter Acid Copter Roll Over Gimme aBreak RadicalAbuse Echodrome Trance Chime Altamira Locko Motif SpaceFactory Get Busy Ayers Rock Altern Saw JP-6 Sync Cold JX Fancy Pad Tune Breath OrchestraGTR Gtr Sweep Trilly Good Bye Spk Voice 4 3 4 2 4 4 2 3 4 4 4 4 4 4 4 4 4 3 3 3 3 4 2 2 1 1 2 1 2 3 1 1 1 3 2 2 4 4 2 4 4 2 4 3 1 4 4 2 1 2 2 1 2 4 4 1 1 1 1 2 2 2 2 4

* The numbers in parenthesis following the Patch name represent the B.P.M. (tempo) when played at the C4 key. * Note that the Release Time has been set to a fairly long value for some of the patches. As a result, if your sound generator has been set so Patch Remain is ON, the release portion of a previously sounding patch may continue to be heard even after switching to a new

Voice: number of voice

173

Appendices

Patch List

s B.P.M. CONVERSION TABLE


By changing the pitch, you can change the B.P.M. (tempo). The B.P.M. used when sampling the original (Original B.P.M.) is reproduced by the C4 key when both c.t. (Coarse Tune) and f.t. (Fine Tune) are at 0. If you want to obtain twice the tempo of the original B.P.M., either play the C5 key (key one octave above), or set c.t. (Coarse Tune) to +12 and play the C4 key. For specifics, refer to the separate B.P.M. Conversion Table.
dst 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140

Original B.P.M.
key F# 2 F# 2 G 2 G 2 G# 2 G# 2 G# 2 A 2 A 2 A 2 A# 2 A# 2 A# 2 B 2 B 2 B 2 C 3 C 3 C 3 C# 3 C# 3 C# 3 C# 3 D 3 D 3 D 3 D 3 D# 3 D# 3 D# 3 E 3 E 3 E 3 E 3 E 3 F 3 F 3 F 3 F 3 F# 3 F# 3 F# 3 F# 3 F# 3 G 3 G 3 G 3 G 3 G 3 G# 3 G# 3 G# 3 G# 3 G# 3 A 3 A 3 A 3 A 3 A 3 A 3 A# 3 A# 3 A# 3 A# 3 A# 3 A# 3 B 3 B 3 B 3 B 3 B 3 B 3 C 4 C 4 C 4 C 4 C 4 C 4 C 4 C# 4 C# 4 C# 4 C# 4 C# 4 C# 4 C# 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D# 4 D# 4 D# 4 D# 4 D# 4 D# 4 c.t -18 -18 -17 -17 -16 -16 -16 -15 -15 -15 -14 -14 -14 -13 -13 -13 -12 -12 -12 -11 -11 -11 -11 -10 -10 -10 -10 -09 -09 -09 -08 -08 -08 -08 -08 -07 -07 -07 -07 -06 -06 -06 -06 -06 -05 -05 -05 -05 -05 -04 -04 -04 -04 -04 -03 -03 -03 -03 -03 -03 -02 -02 -02 -02 -02 -02 -01 -01 -01 -01 -01 -01 00 00 00 00 00 00 00 +01 +01 +01 +01 +01 +01 +01 +02 +02 +02 +02 +02 +02 +02 +02 +03 +03 +03 +03 +03 +03 f.t -01 +41 -18 +22 -39 -01 +36 -28 +08 +43 -23 +11 +44 -24 +08 +39 -30 00 +30 -41 -13 +15 +43 -30 -03 +24 +50 -25 +01 +26 -50 -26 -02 +22 +45 -32 -09 +13 +35 -43 -22 -01 +20 +41 -38 -18 +02 +22 +41 -39 -20 -01 +17 +36 -46 -28 -10 +08 +26 +43 -40 -23 -06 +11 +28 +44 -40 -24 -08 +08 +24 +39 -45 -30 -15 00 +15 +30 +44 -41 -27 -13 +01 +15 +29 +43 -43 -30 -16 -03 +11 +24 +37 +50 -37 -25 -12 +01 +13 +26 dst 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240

116
key D# 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 F 4 F 4 F 4 F 4 F 4 F 4 F 4 F 4 F 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 G 4 G 4 G 4 G 4 G 4 G 4 G 4 G 4 G 4 G 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A# 4 A# 4 A# 4 A# 4 A# 4 A# 4 A# 4 A# 4 A# 4 A# 4 A# 4 A# 4 B 4 B 4 B 4 B 4 B 4 B 4 B 4 B 4 B 4 B 4 B 4 B 4 B 4 C 5 C 5 C 5 C 5 C 5 C 5 C 5 C 5 C 5 C 5 C 5 C 5 C 5 C# 5 C# 5 c.t +03 +04 +04 +04 +04 +04 +04 +04 +04 +04 +05 +05 +05 +05 +05 +05 +05 +05 +05 +06 +06 +06 +06 +06 +06 +06 +06 +06 +07 +07 +07 +07 +07 +07 +07 +07 +07 +07 +08 +08 +08 +08 +08 +08 +08 +08 +08 +08 +08 +09 +09 +09 +09 +09 +09 +09 +09 +09 +09 +09 +10 +10 +10 +10 +10 +10 +10 +10 +10 +10 +10 +10 +11 +11 +11 +11 +11 +11 +11 +11 +11 +11 +11 +11 +11 +12 +12 +12 +12 +12 +12 +12 +12 +12 +12 +12 +12 +12 +13 +13 f.t +38 -50 -38 -26 -14 -02 +10 +22 +33 +45 -43 -32 -21 -09 +02 +13 +24 +35 +46 -43 -32 -22 -11 -01 +10 +20 +31 +41 -49 -38 -28 -18 -08 +02 +12 +22 +32 +41 -49 -39 -30 -20 -11 -01 +08 +17 +27 +36 +45 -46 -37 -28 -19 -10 -01 +08 +17 +26 +34 +43 -48 -40 -31 -23 -14 -06 +03 +11 +19 +28 +36 +44 -48 -40 -32 -24 -16 -08 00 +08 +16 +24 +32 +39 +47 -45 -38 -30 -23 -15 -07 00 +07 +15 +22 +30 +37 +44 -49 -41

How to Read the Table


q B.P.M. Conversion When Creating Patches
The Original B.P.M. is the B.P.M. obtained when the Waveform is played by the C4 key (when both Coarse and Fine Tune are at 0). (Marked with in table.) For example, to play a B.P.M. 116 Waveform at B.P.M. 120:
dst 116 : 120 key C 4 : : C# 4 c.t 00 : +01 f.t 00 -41

Method 1: Look up the f.t. (Fine Tune) parameter in the table, and you will see that the setting for f.t. should be -41 and that the C#4 key should be played. Method 2: Look up the c.t.(Coarse Tune) and f.t. (Fine Tune) parameters in the table, and you will see that the setting for c.t.should be +1, and that for f.t. should be -41, and that the C4 key should be played. So, as you can see from the above example, the settings you should make change depending on whether you want to play using the same key or not.

q B.P.M. Conversion When Creating Rhythm Sets


Given that the Original Pitch for the Rhythm Set is C4, you need to set c.t.(Coarse Tune) for the range C-1 through G9. To play a Phrase Loop Waveform at the Original B.P.M., set c.t. (Coarse Tune) to C4, and f.t. (Fine Tune) to 0. To change the B.P.M. for a Phrase Loop Waveform in a Rhythm Set, look up key and f.t. (Fine Tune) in the table, and make the necessary settings.

174

Patch List

Original B.P.M.
dst 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 key F 2 F# 2 F# 2 G 2 G 2 G 2 G# 2 G# 2 G# 2 A 2 A 2 A# 2 A# 2 A# 2 A# 2 B 2 B 2 B 2 C 3 C 3 C 3 C# 3 C# 3 C# 3 C# 3 D 3 D 3 D 3 D 3 D# 3 D# 3 D# 3 D# 3 E 3 E 3 E 3 E 3 F 3 F 3 F 3 F 3 F 3 F# 3 F# 3 F# 3 F# 3 F# 3 G 3 G 3 G 3 G 3 G 3 G# 3 G# 3 G# 3 G# 3 G# 3 G# 3 A 3 A 3 A 3 A 3 A 3 A# 3 A# 3 A# 3 A# 3 A# 3 A# 3 A# 3 B 3 B 3 B 3 B 3 B 3 B 3 C 4 C 4 C 4 C 4 C 4 C 4 C 4 C# 4 C# 4 C# 4 C# 4 C# 4 C# 4 C# 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D# 4 D# 4 c.t -19 -18 -18 -17 -17 -17 -16 -16 -16 -15 -15 -14 -14 -14 -14 -13 -13 -13 -12 -12 -12 -11 -11 -11 -11 -10 -10 -10 -10 -09 -09 -09 -09 -08 -08 -08 -08 -07 -07 -07 -07 -07 -06 -06 -06 -06 -06 -05 -05 -05 -05 -05 -04 -04 -04 -04 -04 -04 -03 -03 -03 -03 -03 -02 -02 -02 -02 -02 -02 -02 -01 -01 -01 -01 -01 -01 00 00 00 00 00 00 00 +01 +01 +01 +01 +01 +01 +01 +02 +02 +02 +02 +02 +02 +02 +02 +03 +03 f.t +41 -17 +23 -37 +02 +40 -23 +14 +49 -16 +19 -48 -15 +18 +49 -19 +11 +41 -29 00 +29 -43 -16 +12 +39 -35 -09 +17 +42 -33 -09 +16 +40 -37 -14 +09 +32 -46 -24 -02 +20 +41 -38 -17 +03 +23 +43 -37 -17 +02 +21 +40 -41 -23 -04 +14 +32 +49 -33 -16 +02 +19 +36 -48 -31 -15 +01 +18 +34 +49 -35 -19 -04 +11 +26 +41 -44 -29 -14 00 +14 +29 +43 -43 -29 -16 -02 +12 +25 +39 -48 -35 -22 -09 +04 +17 +29 +42 -46 -33 dst 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240

120
key D# 4 D# 4 D# 4 D# 4 D# 4 D# 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 F 4 F 4 F 4 F 4 F 4 F 4 F 4 F 4 F 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 G 4 G 4 G 4 G 4 G 4 G 4 G 4 G 4 G 4 G 4 G 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A# 4 A# 4 A# 4 A# 4 A# 4 A# 4 A# 4 A# 4 A# 4 A# 4 A# 4 A# 4 A# 4 B 4 B 4 B 4 B 4 B 4 B 4 B 4 B 4 B 4 B 4 B 4 B 4 B 4 C 5 C 5 C 5 C 5 C 5 C 5 C 5 c.t +03 +03 +03 +03 +03 +03 +04 +04 +04 +04 +04 +04 +04 +04 +04 +05 +05 +05 +05 +05 +05 +05 +05 +05 +06 +06 +06 +06 +06 +06 +06 +06 +06 +06 +07 +07 +07 +07 +07 +07 +07 +07 +07 +07 +07 +08 +08 +08 +08 +08 +08 +08 +08 +08 +08 +08 +09 +09 +09 +09 +09 +09 +09 +09 +09 +09 +09 +10 +10 +10 +10 +10 +10 +10 +10 +10 +10 +10 +10 +10 +11 +11 +11 +11 +11 +11 +11 +11 +11 +11 +11 +11 +11 +12 +12 +12 +12 +12 +12 +12 f.t -21 -09 +04 +16 +28 +40 -49 -37 -25 -14 -02 +09 +21 +32 +43 -46 -35 -24 -13 -02 +09 +20 +30 +41 -49 -38 -28 -17 -07 +03 +13 +23 +33 +43 -47 -37 -27 -17 -08 +02 +12 +21 +31 +40 +49 -41 -32 -23 -14 -04 +05 +14 +23 +32 +41 +49 -42 -33 -24 -16 -07 +02 +10 +19 +27 +36 +44 -48 -39 -31 -23 -15 -07 +01 +10 +18 +26 +34 +41 +49 -43 -35 -27 -19 -12 -04 +04 +11 +19 +26 +34 +41 +49 -44 -36 -29 -22 -14 -07 00 dst 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140

Original B.P.M.
key E 2 E 2 F 2 F 2 F 2 F# 2 F# 2 F# 2 G 2 G 2 G# 2 G# 2 G# 2 A 2 A 2 A 2 A 2 A# 2 A# 2 A# 2 B 2 B 2 B 2 B 2 C 3 C 3 C 3 C# 3 C# 3 C# 3 C# 3 D 3 D 3 D 3 D 3 D 3 D# 3 D# 3 D# 3 D# 3 E 3 E 3 E 3 E 3 E 3 F 3 F 3 F 3 F 3 F 3 F# 3 F# 3 F# 3 F# 3 F# 3 F# 3 G 3 G 3 G 3 G 3 G 3 G# 3 G# 3 G# 3 G# 3 G# 3 G# 3 A 3 A 3 A 3 A 3 A 3 A 3 A 3 A# 3 A# 3 A# 3 A# 3 A# 3 A# 3 A# 3 B 3 B 3 B 3 B 3 B 3 B 3 B 3 C 4 C 4 C 4 C 4 C 4 C 4 C 4 C# 4 C# 4 C# 4 C# 4 C# 4 c.t -20 -20 -19 -19 -19 -18 -18 -18 -17 -17 -16 -16 -16 -15 -15 -15 -15 -14 -14 -14 -13 -13 -13 -13 -12 -12 -12 -11 -11 -11 -11 -10 -10 -10 -10 -10 -09 -09 -09 -09 -08 -08 -08 -08 -08 -07 -07 -07 -07 -07 -06 -06 -06 -06 -06 -06 -05 -05 -05 -05 -05 -04 -04 -04 -04 -04 -04 -03 -03 -03 -03 -03 -03 -03 -02 -02 -02 -02 -02 -02 -02 -01 -01 -01 -01 -01 -01 -01 00 00 00 00 00 00 00 +01 +01 +01 +01 +01 f.t -24 +18 -42 -02 +37 -25 +12 +49 -16 +19 -46 -13 +20 -47 -16 +16 +46 -24 +06 +35 -36 -08 +19 +47 -26 00 +26 -48 -23 +02 +26 -49 -25 -02 +21 +44 -33 -11 +11 +33 -45 -24 -03 +18 +38 -42 -22 -02 +18 +37 -44 -25 -06 +12 +31 +49 -33 -16 +02 +19 +37 -46 -29 -13 +04 +20 +36 -47 -31 -16 00 +16 +31 +46 -39 -24 -09 +06 +21 +35 +49 -36 -22 -08 +06 +19 +33 +47 -40 -26 -13 00 +13 +26 +39 -48 -36 -23 -11 +02 dst 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240

132
key C# 4 C# 4 C# 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D# 4 D# 4 D# 4 D# 4 D# 4 D# 4 D# 4 D# 4 D# 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 F 4 F 4 F 4 F 4 F 4 F 4 F 4 F 4 F 4 F 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 G 4 G 4 G 4 G 4 G 4 G 4 G 4 G 4 G 4 G 4 G 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A# 4 A# 4 A# 4 A# 4 A# 4 A# 4 A# 4 A# 4 A# 4 A# 4 A# 4 A# 4 c.t +01 +01 +01 +02 +02 +02 +02 +02 +02 +02 +02 +02 +03 +03 +03 +03 +03 +03 +03 +03 +03 +04 +04 +04 +04 +04 +04 +04 +04 +04 +04 +05 +05 +05 +05 +05 +05 +05 +05 +05 +05 +06 +06 +06 +06 +06 +06 +06 +06 +06 +06 +06 +07 +07 +07 +07 +07 +07 +07 +07 +07 +07 +07 +08 +08 +08 +08 +08 +08 +08 +08 +08 +08 +08 +08 +09 +09 +09 +09 +09 +09 +09 +09 +09 +09 +09 +09 +09 +10 +10 +10 +10 +10 +10 +10 +10 +10 +10 +10 +10 f.t +14 +26 +39 -49 -37 -25 -14 -02 +10 +21 +33 +44 -44 -33 -22 -11 00 +11 +22 +33 +44 -45 -35 -24 -14 -03 +07 +18 +28 +38 +48 -42 -32 -22 -12 -02 +08 +18 +27 +37 +47 -44 -34 -25 -16 -06 +03 +12 +21 +31 +40 +49 -42 -33 -24 -16 -07 +02 +11 +19 +28 +37 +45 -46 -38 -29 -21 -13 -04 +04 +12 +20 +28 +36 +45 -47 -39 -31 -24 -16 -08 00 +08 +16 +23 +31 +39 +46 -46 -39 -31 -24 -16 -09 -01 +06 +13 +21 +28 +35 dst 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140

Original B.P.M.
key D# 2 D# 2 E 2 E 2 F 2 F 2 F 2 F# 2 F# 2 F# 2 G 2 G 2 G 2 G# 2 G# 2 G# 2 A 2 A 2 A 2 A# 2 A# 2 A# 2 A# 2 B 2 B 2 B 2 B 2 C 3 C 3 C 3 C 3 C# 3 C# 3 C# 3 C# 3 D 3 D 3 D 3 D 3 D# 3 D# 3 D# 3 D# 3 D# 3 E 3 E 3 E 3 E 3 E 3 F 3 F 3 F 3 F 3 F 3 F# 3 F# 3 F# 3 F# 3 F# 3 F# 3 G 3 G 3 G 3 G 3 G 3 G 3 G# 3 G# 3 G# 3 G# 3 G# 3 G# 3 A 3 A 3 A 3 A 3 A 3 A 3 A 3 A# 3 A# 3 A# 3 A# 3 A# 3 A# 3 A# 3 B 3 B 3 B 3 B 3 B 3 B 3 B 3 B 3 C 4 C 4 C 4 C 4 C 4 C 4 c.t -21 -21 -20 -20 -19 -19 -19 -18 -18 -18 -17 -17 -17 -16 -16 -16 -15 -15 -15 -14 -14 -14 -14 -13 -13 -13 -13 -12 -12 -12 -12 -11 -11 -11 -11 -10 -10 -10 -10 -09 -09 -09 -09 -09 -08 -08 -08 -08 -08 -07 -07 -07 -07 -07 -06 -06 -06 -06 -06 -06 -05 -05 -05 -05 -05 -05 -04 -04 -04 -04 -04 -04 -03 -03 -03 -03 -03 -03 -03 -02 -02 -02 -02 -02 -02 -02 -01 -01 -01 -01 -01 -01 -01 -01 00 00 00 00 00 00 f.t -01 +41 -19 +21 -40 -02 +35 -28 +07 +42 -23 +10 +43 -24 +07 +39 -31 -01 +29 -42 -13 +15 +43 -30 -03 +23 +49 -25 00 +25 +49 -26 -02 +21 +44 -33 -10 +12 +34 -44 -22 -01 +20 +41 -39 -19 +01 +21 +41 -40 -21 -02 +17 +35 -46 -28 -10 +07 +25 +42 -40 -23 -06 +10 +27 +43 -40 -24 -08 +07 +23 +39 -46 -31 -16 -01 +14 +29 +44 -42 -28 -13 +01 +15 +29 +43 -44 -30 -17 -03 +10 +23 +36 +49 -38 -25 -13 00 +12 +25 dst 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240

138
key C 4 C 4 C# 4 C# 4 C# 4 C# 4 C# 4 C# 4 C# 4 C# 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D# 4 D# 4 D# 4 D# 4 D# 4 D# 4 D# 4 D# 4 D# 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 F 4 F 4 F 4 F 4 F 4 F 4 F 4 F 4 F 4 F 4 F 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 G 4 G 4 G 4 G 4 G 4 G 4 G 4 G 4 G 4 G 4 G 4 G 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A 4 A# 4 A# 4 c.t 00 00 +01 +01 +01 +01 +01 +01 +01 +01 +02 +02 +02 +02 +02 +02 +02 +02 +02 +03 +03 +03 +03 +03 +03 +03 +03 +03 +04 +04 +04 +04 +04 +04 +04 +04 +04 +04 +05 +05 +05 +05 +05 +05 +05 +05 +05 +05 +05 +06 +06 +06 +06 +06 +06 +06 +06 +06 +06 +06 +07 +07 +07 +07 +07 +07 +07 +07 +07 +07 +07 +07 +08 +08 +08 +08 +08 +08 +08 +08 +08 +08 +08 +08 +08 +09 +09 +09 +09 +09 +09 +09 +09 +09 +09 +09 +09 +09 +10 +10 f.t +37 +49 -38 -26 -14 -02 +09 +21 +33 +44 -44 -33 -21 -10 +01 +12 +23 +34 +45 -44 -33 -22 -12 -01 +09 +20 +30 +41 -49 -39 -29 -19 -09 +01 +11 +21 +31 +41 -50 -40 -30 -21 -11 -02 +07 +17 +26 +35 +44 -46 -37 -28 -19 -10 -01 +07 +16 +25 +34 +42 -49 -40 -32 -23 -15 -06 +02 +10 +19 +27 +35 +43 -49 -40 -32 -24 -16 -08 00 +07 +15 +23 +31 +39 +46 -46 -38 -31 -23 -16 -08 -01 +07 +14 +22 +29 +36 +44 -49 -42

175

Appendices

Patch List

Original B.P.M.
dst 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 key D 2 D# 2 D# 2 D# 2 E 2 E 2 F 2 F 2 F 2 F# 2 F# 2 F# 2 G 2 G 2 G 2 G# 2 G# 2 G# 2 A 2 A 2 A 2 A 2 A# 2 A# 2 A# 2 A# 2 B 2 B 2 B 2 C 3 C 3 C 3 C 3 C 3 C# 3 C# 3 C# 3 C# 3 D 3 D 3 D 3 D 3 D 3 D# 3 D# 3 D# 3 D# 3 D# 3 E 3 E 3 E 3 E 3 E 3 F 3 F 3 F 3 F 3 F 3 F# 3 F# 3 F# 3 F# 3 F# 3 F# 3 G 3 G 3 G 3 G 3 G 3 G 3 G 3 G# 3 G# 3 G# 3 G# 3 G# 3 G# 3 A 3 A 3 A 3 A 3 A 3 A 3 A 3 A# 3 A# 3 A# 3 A# 3 A# 3 A# 3 A# 3 A# 3 B 3 B 3 B 3 B 3 B 3 B 3 B 3 C 4 c.t -22 -21 -21 21 -20 -20 -19 -19 -19 -18 -18 -18 -17 -17 -17 -16 -16 -16 -15 -15 -15 -15 -14 -14 -14 -14 -13 -13 -13 -12 -12 -12 -12 -12 -11 -11 -11 -11 -10 -10 -10 -10 -10 -09 -09 -09 -09 -09 -08 -08 -08 -08 -08 -07 -07 -07 -07 -07 -06 -06 -06 -06 -06 -06 -05 -05 -05 -05 -05 -05 -05 -04 -04 -04 -04 -04 -04 -03 -03 -03 -03 -03 -03 -03 -02 -02 -02 -02 -02 -02 -02 -02 -01 -01 -01 -01 -01 -01 -01 00 f.t +25 -33 +08 +47 -14 +24 -38 -02 +34 -31 +03 +37 -30 +02 +34 -35 -04 +26 -45 -16 +13 +41 -31 -04 +23 +49 -25 +01 +26 -49 -24 00 +24 +47 -29 -06 +16 +39 -39 -18 +04 +25 +46 -33 -13 +08 +28 +47 -33 -14 +05 +24 +43 -38 -20 -02 +16 +34 -49 -31 -14 +03 +20 +37 -47 -30 -14 +02 +18 +34 +49 -35 -20 -04 +11 +26 +41 -45 -30 -16 -01 +13 +27 +41 -45 -31 -17 -04 +10 +23 +36 +49 -38 -25 -12 +01 +14 +26 +39 -49 dst 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240

144
key C 4 C 4 C 4 C 4 C 4 C 4 C 4 C 4 C# 4 C# 4 C# 4 C# 4 C# 4 C# 4 C# 4 C# 4 C# 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D# 4 D# 4 D# 4 D# 4 D# 4 D# 4 D# 4 D# 4 D# 4 D# 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 F 4 F 4 F 4 F 4 F 4 F 4 F 4 F 4 F 4 F 4 F 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 G 4 G 4 G 4 G 4 G 4 G 4 G 4 G 4 G 4 G 4 G 4 G 4 G 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 G# 4 A 4 A 4 A 4 A 4 A 4 c.t 00 00 00 00 00 00 00 00 +01 +01 +01 +01 +01 +01 +01 +01 +01 +02 +02 +02 +02 +02 +02 +02 +02 +02 +03 +03 +03 +03 +03 +03 +03 +03 +03 +03 +04 +04 +04 +04 +04 +04 +04 +04 +04 +04 +05 +05 +05 +05 +05 +05 +05 +05 +05 +05 +05 +06 +06 +06 +06 +06 +06 +06 +06 +06 +06 +06 +06 +07 +07 +07 +07 +07 +07 +07 +07 +07 +07 +07 +07 +07 +08 +08 +08 +08 +08 +08 +08 +08 +08 +08 +08 +08 +08 +09 +09 +09 +09 +09 f.t -36 -24 -12 00 +12 +24 +36 +47 -41 -29 -18 -06 +05 +16 +27 +39 +50 -39 -28 -18 -07 +04 +15 +25 +36 +46 -43 -33 -23 -13 -02 +08 +18 +28 +38 +47 -43 -33 -23 -14 -04 +05 +15 +24 +34 +43 -48 -38 -29 -20 -11 -02 +07 +16 +25 +34 +43 -49 -40 -31 -23 -14 -06 +03 +11 +20 +28 +37 +45 -47 -39 -30 -22 -14 -06 +02 +10 +18 +26 +34 +42 +49 -43 -35 -27 -20 -12 -04 +03 +11 +18 +26 +33 +41 +48 -45 -37 -30 -23 -16 dst 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140

Original B.P.M.
key C 2 C# 2 C# 2 D 2 D 2 D 2 D# 2 D# 2 E 2 E 2 E 2 F 2 F 2 F 2 F# 2 F# 2 F# 2 F# 2 G 2 G 2 G 2 G# 2 G# 2 G# 2 G# 2 A 2 A 2 A 2 A 2 A# 2 A# 2 A# 2 A# 2 B 2 B 2 B 2 B 2 C 3 C 3 C 3 C 3 C 3 C# 3 C# 3 C# 3 C# 3 C# 3 D 3 D 3 D 3 D 3 D 3 D# 3 D# 3 D# 3 D# 3 D# 3 E 3 E 3 E 3 E 3 E 3 E 3 F 3 F 3 F 3 F 3 F 3 F 3 F# 3 F# 3 F# 3 F# 3 F# 3 F# 3 F# 3 G 3 G 3 G 3 G 3 G 3 G 3 G 3 G# 3 G# 3 G# 3 G# 3 G# 3 G# 3 G# 3 A 3 A 3 A 3 A 3 A 3 A 3 A 3 A 3 A# 3 A# 3 c.t -24 -23 -23 -22 -22 -22 -21 -21 -20 -20 -20 -19 -19 -19 -18 -18 -18 -18 -17 -17 -17 -16 -16 -16 -16 -15 -15 -15 -15 -14 -14 -14 -14 -13 -13 -13 -13 -12 -12 -12 -12 -12 -11 -11 -11 -11 -11 -10 -10 -10 -10 -10 -09 -09 -09 -09 -09 -08 -08 -08 -08 -08 -08 -07 -07 -07 -07 -07 -07 -06 -06 -06 -06 -06 -06 -06 -05 -05 -05 -05 -05 -05 -05 -04 -04 -04 -04 -04 -04 -04 -03 -03 -03 -03 -03 -03 -03 -03 -02 -02 f.t +43 -16 +25 -35 +04 +42 -21 +16 -49 -14 +21 -46 -13 +20 -49 -17 +13 +43 -27 +02 +31 -41 -14 +14 +41 -33 -07 +19 +44 -31 -07 +18 +41 -35 -12 +11 +34 -44 -22 00 +22 +43 -36 -16 +05 +25 +45 -35 -15 +04 +23 +42 -39 -21 -02 +16 +34 -49 -31 -14 +04 +21 +37 -46 -29 -13 +03 +20 +36 -49 -33 -17 -02 +13 +28 +43 -42 -27 -13 +02 +16 +31 +45 -41 -27 -14 00 +14 +27 +41 -46 -33 -20 -07 +06 +19 +31 +44 -44 -31 dst 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240

160
key A# 3 A# 3 A# 3 A# 3 A# 3 A# 3 B 3 B 3 B 3 B 3 B 3 B 3 B 3 B 3 B 3 C 4 C 4 C 4 C 4 C 4 C 4 C 4 C 4 C 4 C# 4 C# 4 C# 4 C# 4 C# 4 C# 4 C# 4 C# 4 C# 4 C# 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D# 4 D# 4 D# 4 D# 4 D# 4 D# 4 D# 4 D# 4 D# 4 D# 4 D# 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 F 4 F 4 F 4 F 4 F 4 F 4 F 4 F 4 F 4 F 4 F 4 F 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 F# 4 G 4 G 4 G 4 G 4 G 4 G 4 G 4 G 4 c.t -02 -02 -02 -02 -02 -02 -01 -01 -01 -01 -01 -01 -01 -01 -01 00 00 00 00 00 00 00 00 00 +01 +01 +01 +01 +01 +01 +01 +01 +01 +01 +02 +02 +02 +02 +02 +02 +02 +02 +02 +02 +03 +03 +03 +03 +03 +03 +03 +03 +03 +03 +03 +04 +04 +04 +04 +04 +04 +04 +04 +04 +04 +04 +04 +05 +05 +05 +05 +05 +05 +05 +05 +05 +05 +05 +05 +06 +06 +06 +06 +06 +06 +06 +06 +06 +06 +06 +06 +06 +07 +07 +07 +07 +07 +07 +07 +07 f.t -19 -07 +06 +18 +30 +41 -47 -35 -23 -12 00 +11 +23 +34 +45 -44 -33 -22 -11 00 +11 +22 +32 +43 -47 -36 -26 -16 -05 +05 +15 +25 +35 +45 -45 -35 -25 -15 -06 +04 +14 +23 +33 +42 -49 -39 -30 -21 -12 -02 +07 +16 +25 +34 +42 -49 -40 -31 -22 -14 -05 +04 +12 +21 +29 +37 +46 -46 -37 -29 -21 -13 -05 +03 +12 +20 +28 +36 +43 -49 -41 -33 -25 -17 -10 -02 +06 +13 +21 +28 +36 +43 -49 -42 -34 -27 -20 -13 -05 +02 dst 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140

Original B.P.M.
key A# 1 A# 1 B 1 B 1 C 2 C 2 C 2 C# 2 C# 2 C# 2 D 2 D 2 D 2 D# 2 D# 2 D# 2 E 2 E 2 E 2 F 2 F 2 F 2 F 2 F# 2 F# 2 F# 2 G 2 G 2 G 2 G 2 G# 2 G# 2 G# 2 G# 2 G# 2 A 2 A 2 A 2 A 2 A# 2 A# 2 A# 2 A# 2 A# 2 B 2 B 2 B 2 B 2 B 2 C 3 C 3 C 3 C 3 C 3 C# 3 C# 3 C# 3 C# 3 C# 3 C# 3 D 3 D 3 D 3 D 3 D 3 D 3 D# 3 D# 3 D# 3 D# 3 D# 3 D# 3 E 3 E 3 E 3 E 3 E 3 E 3 E 3 F 3 F 3 F 3 F 3 F 3 F 3 F 3 F# 3 F# 3 F# 3 F# 3 F# 3 F# 3 F# 3 G 3 G 3 G 3 G 3 G 3 G 3 G 3 c.t -26 -26 -25 -25 -24 -24 -24 -23 -23 -23 -22 -22 -22 -21 -21 -21 -20 -20 -20 -19 -19 -19 -19 -18 -18 -18 -17 -17 -17 -17 -16 -16 -16 -16 -16 -15 -15 -15 -15 -14 -14 -14 -14 -14 -13 -13 -13 -13 -13 -12 -12 -12 -12 -12 -11 -11 -11 -11 -11 -11 -10 -10 -10 -10 -10 -10 -09 -09 -09 -09 -09 -09 -08 -08 -08 -08 -08 -08 -08 -07 -07 -07 -07 -07 -07 -07 -06 -06 -06 -06 -06 -06 -06 -05 -05 -05 -05 -05 -05 -05 f.t +01 +43 -17 +23 -38 00 +37 -26 +09 +44 -21 +12 +45 -22 +09 +41 -29 +01 +31 -40 -11 +17 +44 -28 -01 +25 -49 -23 +02 +27 -49 -24 00 +23 +46 -31 -08 +14 +36 -42 -20 +01 +22 +43 -37 -17 +03 +23 +43 -38 -19 00 +19 +37 -44 -26 -08 +09 +27 +44 -38 -21 -04 +12 +29 +45 -39 -22 -06 +09 +25 +41 -44 -29 -14 +01 +16 +31 +46 -40 -26 -11 +03 +17 +31 +44 -42 -28 -15 -01 +12 +25 +38 -49 -36 -23 -11 +02 +14 +27 dst 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240

184
key G 3 G# 3 G# 3 G# 3 G# 3 G# 3 G# 3 G# 3 G# 3 G# 3 A 3 A 3 A 3 A 3 A 3 A 3 A 3 A 3 A 3 A# 3 A# 3 A# 3 A# 3 A# 3 A# 3 A# 3 A# 3 A# 3 B 3 B 3 B 3 B 3 B 3 B 3 B 3 B 3 B 3 B 3 C 4 C 4 C 4 C 4 C 4 C 4 C 4 C 4 C 4 C 4 C 4 C# 4 C# 4 C# 4 C# 4 C# 4 C# 4 C# 4 C# 4 C# 4 C# 4 C# 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D 4 D# 4 D# 4 D# 4 D# 4 D# 4 D# 4 D# 4 D# 4 D# 4 D# 4 D# 4 D# 4 D# 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 E 4 F 4 F 4 c.t -05 -04 -04 -04 -04 -04 -04 -04 -04 -04 -03 -03 -03 -03 -03 -03 -03 -03 -03 -02 -02 -02 -02 -02 -02 -02 -02 -02 -01 -01 -01 -01 -01 -01 -01 -01 -01 -01 00 00 00 00 00 00 00 00 00 00 00 +01 +01 +01 +01 +01 +01 +01 +01 +01 +01 +01 +02 +02 +02 +02 +02 +02 +02 +02 +02 +02 +02 +02 +03 +03 +03 +03 +03 +03 +03 +03 +03 +03 +03 +03 +03 +04 +04 +04 +04 +04 +04 +04 +04 +04 +04 +04 +04 +04 +05 +05 f.t +39 -49 -36 -24 -12 00 +11 +23 +35 +46 -42 -31 -19 -08 +03 +14 +25 +36 +47 -42 -31 -20 -10 +01 +11 +22 +32 +43 -47 -37 -27 -17 -07 +03 +13 +23 +33 +43 -48 -38 -28 -19 -09 00 +09 +19 +28 +37 +46 -44 -35 -26 -17 -08 +01 +09 +18 +27 +36 +44 -47 -38 -30 -21 -13 -04 +04 +12 +21 +29 +37 +45 -47 -39 -30 -22 -14 -06 +01 +09 +17 +25 +33 +41 +48 -44 -36 -29 -21 -14 -06 +01 +09 +16 +24 +31 +38 +46 -47 -40

176

Rhythm Set List


USER (User)
Note No. 35 Scratch 1 C2 36 37 38 39 40 41 43 44 45 46 47 C3 48 49 50 51 52 53 55 56 57 58 59 C4 60 61 62 63 64 65 67 68 69 70 71 C5 72 73 74 75 76 77 79 80 81 82 83 C6 84 85 86 87 88 89 91 92 93 94 95 C7 96 97 98 90 78 66 54 42
001 HouseDrumSet 1 808 SN Dry Stick 808 SN 808 Claps 808 SN 808 Kick 606 HiHat Cl 808 SN 606 HiHat Cl 808 Kick 606 HiHat Op 808 SN 808 Kick Crash 1 808 SN Ride 2 REV Crash 1 Ride Bell 1 Tambourine Crash 1 Cowbell 1 Crash 1 Vibraslap Ride 2 Bongo Hi Bongo Lo Cga Mute Hi Cga Open Hi Cga Open Lo Timbale Timbale Agogo Agogo Cabasa Cut Maracas Soft Pad B Soft Pad A Long Guiro Long Guiro Claves Wood Block Wood Block Cuica Cuica Open Triangl Open Triangl Cabasa Cut Tambourine Old Kick Scratch 1 Piccolo SN Scratch 3 White Noise Synth Saw 1 Synth Pulse1 Back Hit Tekno Hit Orch. Hit Philly Hit REV Back Hit MC500 Beep 1 R8 Click MC500 Beep 2 002 JazzDrumSet1 Hybrid Kick2 Hybrid Kick1 Side Stick Ballad SN Brush Slap Brush Swish Verb Tom Lo Cl HiHat 1 Verb Tom Lo Pedal HiHat Verb Tom Hi Op HiHat Verb Tom Hi Verb Tom Hi Crash 1 Verb Tom Hi Ride 2 China Cym Ride Bell 1 Tambourine Crash 1 Cowbell 1 Crash 1 Vibraslap Ride 2 Bongo Hi Bongo Lo Cga Mute Hi Cga Open Hi Cga Open Lo Timbale Timbale Agogo Agogo Cabasa Up Maracas Soft Pad B Soft Pad A Long Guiro Long Guiro Claves Wood Block Wood Block Cuica Cuica Open Triangl Open Triangl Cabasa Cut Spectrum Wind Chimes Wood Block Cga Slap Dry Tom Lo Lite Kick Hybrid Kick2 Old Kick 808 Kick Natural SN1 Natural SN2 SN Roll Natural SN2 Metronome 2 R8 Click Metronome 1

PR-A (Preset A Group)


001 PopDrumSet 1 Verb Kick Hybrid Kick1 Side Stick Natural SN2 808 Claps SN Roll Verb Tom Lo Cl HiHat 1 Verb Tom Lo Cl HiHat 2 Verb Tom Hi Op HiHat Verb Tom Hi Verb Tom Hi Crash 1 Verb Tom Hi Ride 2 China Cym Ride Bell 1 Tambourine Crash 1 Cowbell 1 Crash 1 Cowbell 1 Ride Bell 1 Cga Mute Hi Cga Mute Lo Cga Slap Cga Open Hi Cga Open Lo Timbale Timbale Agogo Agogo Cabasa Up Maracas Soft Pad A Soft Pad B Long Guiro Long Guiro Claves Wood Block Wood Block Cuica Cuica Open Triangl Open Triangl Cabasa Cut Spectrum Wind Chimes Wood Block Cga Slap Dry Tom Lo Lite Kick Hybrid Kick2 Old Kick Pop Voice Wind Agogo Op HiHat Anklungs Op HiHat Metronome 2 R8 Click Metronome 1 002 PopDrumSet 2 Hybrid Kick1 Round Kick Dry Stick Piccolo SN Hand Claps Piccolo SN Verb Tom Lo Cl HiHat 1 Verb Tom Lo Cl HiHat 2 Verb Tom Hi Op HiHat Verb Tom Hi Verb Tom Hi Crash 1 Verb Tom Hi Ride 1 China Cym Ride Bell 1 Tambourine Crash 1 Cowbell 1 Crash 1 Cowbell 1 Ride Bell 1 Cga Mute Hi Cga Mute Lo Cga Slap Cga Open Hi Cga Open Lo Timbale Timbale Agogo Agogo Cabasa Up Maracas Cabasa Down Cabasa Cut 808 Kick 808 SN DIGI Bell 1 808 SN 808 Kick Spectrum 808 Kick Spectrum 808 Kick Spectrum 808 Kick 808 Kick Feedbackwave 808 Kick Feedbackwave Pop Voice Pop Voice Wind Agogo Pop Voice Wind Agogo Op HiHat Anklungs Op HiHat Metronome 2 R8 Click Metronome 1

PR-B (Preset B Group)


001 PowerDrumSet Verb Kick Round Kick Dry Stick Piccolo SN 808 Claps Natural SN2 Verb Tom Lo Cl HiHat 1 Verb Tom Lo Pedal HiHat Verb Tom Lo Op HiHat Verb Tom Lo Verb Tom Hi Crash 1 Verb Tom Hi Ride 1 China Cym Ride Bell 1 Tambourine Crash 1 Cowbell 1 Crash 1 Vibraslap Ride 1 Bongo Hi Bongo Lo Cga Mute Hi Cga Open Hi Cga Open Lo Timbale Timbale Agogo Agogo Cabasa Up Maracas Soft Pad A Soft Pad B Long Guiro Long Guiro Claves Wood Block Wood Block Cuica Cuica Open Triangl Open Triangl Maracas Ice Rain Wind Chimes Claves 808 SN Verb Tom Hi Piccolo SN Scratch 3 Tin Wave Spectrum REV Steel DR REV Tin Wave REV PiccloSN REV Crash 1 Metronome 2 R8 Click Metronome 1 002 RaveDrumSet 808 Kick Round Kick Side Stick 808 SN 808 Claps 808 SN 808 Kick 606 HiHat Cl Tekno Hit 606 HiHat Cl 808 Kick 606 HiHat Op Tekno Hit 808 Kick Crash 1 Tekno Hit Voice Breath MC500 Beep 1 MC500 Beep 2 R8 Click Pizz DIGI Bell 1 Rattles Ride Bell 1 REV Tamb 2.2 Vibwave Low Pink NZ Kalimba Metal Wind Lead Wave Tin Wave Agogo Lite Kick Agogo Lite Kick Agogo Gtr Harm A Gtr Harm A Piano Thump Natural SN1 Hand Claps Natural SN1 808 SN PowerChord B Hybrid Kick2 PowerChord B Gt.FretNoise Banjo B Slap Bass 1 Oboe mf A Shakuhachi Pizz Syn Vox 1 Voice Aahs A Voice Oohs2A Pop Voice Male Ooh A Voice Breath Org Vox C Vox Noise Vox Noise Applause R8 Click Metronome 2

177

Appendices

Rhythm Set List

PR-C (Preset C Group)


Note No. 35 Round Kick C2 36 37 38 39 40 41 43 44 45 46 47 C3 48 49 50 51 52 53 55 56 57 58 59 C4 60 61 62 63 64 65 67 68 69 70 71 C5 72 73 74 75 76 77 79 80 81 82 83 C6 84 85 86 87 88 89 91 92 93 94 95 C7 96 97 98 90 78 66 54 42
001 JazzDrumSet2 Old Kick Side Stick Ballad SN Hand Claps SN Roll Verb Tom Lo Cl HiHat 2 Dry Tom Lo Pedal HiHat Verb Tom Lo Op HiHat Dry Tom Lo Verb Tom Hi Crash 1 Dry Tom Hi Ride 2 China Cym Ride Bell 1 Tambourine Crash 1 Cowbell 1 Crash 1 Vibraslap Ride 2 Bongo Hi Bongo Lo Cga Mute Hi Cga Open Hi Cga Open Lo Timbale Timbale Agogo Agogo Cabasa Up Maracas Soft Pad A Brush Swish Long Guiro Long Guiro Claves Wood Block Metronome 2 Cuica Cuica Open Triangl Open Triangl Cabasa Cut Spectrum Wind Chimes Wood Block Cga Slap Dry Tom Lo Lite Kick Hybrid Kick2 Old Kick Natural SN2 Natural SN1 Brush Swish Brush Roll Brush Slap Metronome 2 R8 Click Metronome 1 002 OrchDrumSet Old Kick Round Kick Side Stick Ballad SN 808 Claps SN Roll Timpani Timpani Timpani Timpani Timpani Timpani Timpani Timpani Timpani Timpani Timpani Timpani Timpani Tambourine Crash 1 Cowbell 1 Crash 1 Ride 1 Ride 2 Bongo Hi Bongo Lo Cga Mute Hi Cga Open Hi Cga Open Lo Timbale Timbale Agogo Agogo Cabasa Up Maracas Soft Pad A Soft Pad B Long Guiro Long Guiro Claves Wood Block Wood Block Cuica Cuica Open Triangl Open Triangl Cabasa Cut Spectrum Wind Chimes Wood Block Cga Slap Dry Tom Lo Applause Hybrid Kick2 Cl HiHat 1 Round Kick Pedal HiHat Natural SN2 Op HiHat Brush Slap Brush Swish Brush Roll SN Roll

PR-D (GM Group)


001 GM Drum Set Verb Kick Hybrid Kick1 Side Stick Ballad SN 808 Claps Piccolo SN Verb Tom Lo Cl HiHat 1 Verb Tom Lo Pedal HiHat Verb Tom Hi Op HiHat Verb Tom Hi Verb Tom Hi Crash 1 Verb Tom Hi Ride 2 China Cym Ride Bell 1 Tambourine Crash 1 Cowbell 1 Crash 1 Vibraslap Ride 2 Bongo Hi Bongo Lo Cga Mute Hi Cga Open Hi Cga Open Lo Timbale Timbale Agogo Agogo Cabasa Up Maracas Soft Pad A Soft Pad B Long Guiro Long Guiro Claves Wood Block Wood Block Cuica Cuica Open Triangl Open Triangl Cabasa Cut Spectrum Wind Chimes Wood Block Cga Slap Dry Tom Lo Lite Kick Hybrid Kick2 Old Kick 808 Kick Natural SN1 Natural SN2 808 SN Brush Slap Brush Swish Brush Roll SN Roll 002 BrushDrumSet Hybrid Kick2 Hybrid Kick1 Side Stick Brush Swish Brush Slap Brush Roll Dry Tom Lo Cl HiHat 1 Dry Tom Lo Pedal HiHat Dry Tom Hi Op HiHat Dry Tom Hi Dry Tom Hi Crash 1 Dry Tom Hi Ride 2 China Cym Ride Bell 1 Tambourine Crash 1 Cowbell 1 Crash 1 Vibraslap Ride 2 Cga Mute Hi Cga Mute Lo Cga Slap Cga Open Hi Cga Open Lo Timbale Timbale Agogo Agogo Cabasa Up Maracas Soft Pad A Soft Pad B Long Guiro Long Guiro Claves Wood Block Wood Block Cuica Cuica Open Triangl Open Triangl Cabasa Cut Spectrum Wind Chimes Wood Block Cga Slap Dry Tom Lo Lite Kick Hybrid Kick2 Old Kick 808 Kick Natural SN1 Natural SN2 SN Roll Brush Slap Metronome 2 R8 Click Metronome 1

PR-E (Preset E Group)


001 PowerDrmSet2 Verb Kick Round Kick Dry Stick Piccolo SN 808 Claps SN Roll Verb Tom Lo Cl HiHat 1 Verb Tom Lo Pedal HiHat Verb Tom Lo Op HiHat Verb Tom Lo Verb Tom Hi Crash 1 Verb Tom Hi Ride 1 China Cym Ride Bell 1 Tambourine Crash 1 Cowbell 1 Crash 1 Vibraslap Ride 1 Bongo Hi Bongo Lo Cga Mute Hi Cga Open Hi Cga Open Lo Timbale Timbale Agogo Agogo Cabasa Up Maracas Soft Pad A Soft Pad B Long Guiro Long Guiro Claves Wood Block Wood Block Cuica Cuica Open Triangl Open Triangl Maracas Ice Rain Wind Chimes Claves 808 SN Verb Tom Hi Piccolo SN Scratch 3 Tin Wave Spectrum REV Steel DR REV Tin Wave REV PiccloSN REV Crash 1 Metronome 2 R8 Click Metronome 1 002 PowerRaveSet Verb Kick Round Kick Dry Stick Piccolo SN 808 Claps Natural SN2 Verb Tom Lo Cl HiHat 1 Verb Tom Lo Pedal HiHat Verb Tom Lo Op HiHat Verb Tom Lo Verb Tom Hi Crash 1 Verb Tom Hi Ride 1 China Cym Ride Bell 1 Tambourine Crash 1 Cowbell 1 Crash 1 Vibraslap Ride 1 Bongo Hi Bongo Lo Cga Mute Hi Cga Open Hi Cga Open Lo Timbale Timbale Agogo Agogo Agogo Maracas 606 HiHat Cl 606 HiHat Cl 606 HiHat Op Long Guiro Claves Wood Block Wood Block Pizz Syn Vox 1 Voice Aahs A Voice Oohs2A Male Ooh A Ice Rain 808 SN 808 SN 808 SN Hand Claps Voice Breath Scratch 3 Tin Wave Crash 1 Ride Bell 1 REV Tin Wave DIGI Bell 1 Metal Wind Applause R8 Click Metronome 1

178

Rhythm Set List

XP-A (WAVE EXPANSION A: Session)


001

Note No. SessionSet 1 35 Deep Kick 3 C2 36 37 38 39 40 41 43 44 45 46 47 C3 48 49 50 51 52 53 55 56 57 58 59 C4 60 61 62 63 64 65 67 68 69 70 71 C5 72 73 74 75 76 77 79 80 81 82 83 C6 84 85 86 87 88 89 91 92 93 94 95 C7 96 97 98 90 78 66 54 42


Mix Kick Side Stick Solo Snr HC2 Claps 1 90s Snare Verb Tom Lo Cl HiHat 1 Verb Tom Lo Cl HiHat 2 Verb Tom Hi Op HiHat Verb Tom Hi Verb Tom Hi Crash 1 Verb Tom Hi Ride 2 China Cym Ride Bell 1 Tamb.Long Crash 1 Cowbell 1 Crash 1 Cowbell 1 Ride Bell 1 Bongo3 High Bongo3 Low Cga Slap Cga Open Hi Cga Open Lo Timbale Timbale Agogo Agogo Shaker 4 Shaker 5 Soft Pad A Soft Pad B Long Guiro Long Guiro Claves Wood Block Wood Block Cuica Cuica Open Triangl Open Triangl Cabasa Cut Auhvox Tekno Hit 3 Tekno Hit 3 Tekno Hit 2 Tekno Hit 2 FX Bell 2fw FX Bell 1fw FX Bomb Sm.Club fw HC2 Claps 2 Gtr Scrap 707 Claps Gtr Slid Nz Gtr Cut Nz R8 Click Gtr Slap

002 SessionSet 2 Mix Kick Deep Kick 3 Side Stick Loose Snr HC2 Claps 1 Ring Snr Verb Tom Lo Cl HiHat 1 Verb Tom Lo Cl HiHat 2 Verb Tom Hi Op HiHat Verb Tom Hi Verb Tom Hi Crash 1 Verb Tom Hi Ride 2 China Cym Ride Bell 1 Tamb.Long Crash 1 Cowbell 1 Crash 1 Cowbell 1 Ride Bell 1 Bongo3 High Bongo3 Low Cga Slap Cga Open Hi Cga Open Lo Timbale Timbale Agogo Agogo Shaker 4 Shaker 5 Soft Pad A Soft Pad B Long Guiro Long Guiro Claves Wood Block Wood Block Cuica Cuica Open Triangl Open Triangl Cabasa Cut Auhvox Gtr Feedback Gtr Scrap Gtr Slid Nz Gtr Cut Nz Gtr Slap Wah Down 1 Wah Up 1 Wah Down 2 Wah Up 2 Sm.Club Sm.Club fw FX Bell 1fw FX Bell 2fw R8 Click REV Snr Buzz

003 SessionSet 3 Deep Kick 3 TD7 Kick Side Stick Rap Snr 707 Claps House Snr Verb Tom Lo Cl HiHat 1 Verb Tom Lo Cl HiHat 2 Verb Tom Hi Op HiHat Verb Tom Hi Verb Tom Hi Crash 1 Verb Tom Hi Ride 2 China Cym Ride Bell 1 Tamb.Long Crash 1 Cowbell 1 Crash 1 Cowbell 1 Ride Bell 1 Bongo3 High Bongo3 Low Cga Slap Cga Open Hi Cga Open Lo Timbale Timbale Agogo Agogo Shaker 4 Shaker 5 Soft Pad A Soft Pad B Long Guiro Long Guiro Claves Wood Block Wood Block Cuica Cuica Open Triangl Open Triangl Cabasa Cut REV Gt Scrap REV Gt SldNz REV Gt CutNz REV Gt Slap REV TeknHit2 REV TeknHit3 REV Dance K3 REV 909 Snr2 REV 909 Snr3 REV Rap Snr REV Talk Snr REV JinglSnr REV HouseSnr REV Mute Snr R8 Click REV 909 Rim2

004 SessionSet 4 Dance Kick 2 Dance Kick 3 909 Rim 2 909 Snr 2 909 Claps 2 808 Snr 2 909 Tom 2 606 HiHat Cl Verb Tom Lo 606 HiHat Op 909 Tom 2 606 HiHat Op Verb Tom Hi 909 Tom 2 Crash 1 Verb Tom Hi Ride 2 China Cym Ride Bell 1 CR78 Tamb. Crash 1 Cowbell 1 Crash 1 Cowbell 1 Ride Bell 1 Bongo3 High Bongo3 Low Cga Slap Cga Open Hi Cga Open Lo Timbale Timbale Agogo Agogo Shaker 4 Shaker 5 Soft Pad A Soft Pad B Long Guiro Long Guiro Claves Wood Block Wood Block Cuica Cuica Open Triangl Open Triangl Cabasa Cut Auhvox Tekno Hit 3 Tekno Hit 3 Tekno Hit 2 Tekno Hit 2 FX Bell 2fw FX Bell 1fw FX Bomb Sm.Club fw HC2 Claps 2 FingerSnaps2 707 Claps 626 Shaker Tamb.Short R8 Click Tamb.Long

005 SessionSet 5 Kick Ghost Dance Kick 3 909 Rim 2 909 Snr 3 HC2 Claps 2 Talk Snr 909 Tom 2 606 HiHat Cl Verb Tom Lo 606 HiHat Op 909 Tom 2 606 HiHat Op Verb Tom Hi 909 Tom 2 Crash 1 Verb Tom Hi Ride 2 China Cym Ride Bell 1 CR78 Tamb. Crash 1 Cowbell 1 Crash 1 Cowbell 1 Ride Bell 1 Bongo3 High Bongo3 Low Cga Slap Cga Open Hi Cga Open Lo Timbale Timbale Agogo Agogo 626 Shaker Shaker 4 Soft Pad A Soft Pad B Long Guiro Long Guiro Claves Wood Block Wood Block Cuica Cuica Open Triangl Open Triangl Cabasa Cut Auhvox Tekno Hit 3 Tekno Hit 3 Tekno Hit 2 Tekno Hit 2 REV Dance K3 REV TeknHit3 REV TeknHit3 REV TeknHit2 REV TeknHit2 REV 808 Snr2 REV 909 Snr2 REV 909 Snr3 REV HC2 Clp1 R8 Click REV 707 Clps

006 SessionSet 6 Dance Kick 3 Dance Kick 2 Mute Snr Jingle Snr HC2 Claps 2 Tiny Snr 2 909 Tom 2 606 HiHat Cl Verb Tom Lo 606 HiHat Op 909 Tom 2 606 HiHat Op Verb Tom Hi 909 Tom 2 Crash 1 Verb Tom Hi Ride 2 China Cym Ride Bell 1 CR78 Tamb. Crash 1 Cowbell 1 Crash 1 Cowbell 1 Ride Bell 1 Bongo3 High Bongo3 Low Cga Slap Cga Open Hi Cga Open Lo Timbale Timbale Agogo Agogo 626 Shaker Shaker 4 Soft Pad A Soft Pad B Long Guiro Long Guiro Claves Wood Block Wood Block Cuica Cuica Open Triangl Open Triangl Cabasa Cut Auhvox Tekno Hit 3 Tekno Hit 3 Tekno Hit 2 Tekno Hit 2 Tekno Loop REV TeknHit3 REV TeknHit3 REV TeknHit2 REV TeknHit2 Blaster A Juno Rave A Hard 5ths A CR78 Tamb. R8 Click FingerSnap 3

007 SessionSet 7 Deep Kick 3 Mix Kick Side Stick Solo Snr 707 Claps Ring Snr 909 Tom 2 606 HiHat Cl Verb Tom Lo 606 HiHat Cl 909 Tom 2 606 HiHat Op Verb Tom Hi 909 Tom 2 Crash 1 Verb Tom Hi Ride 2 China Cym Ride Bell 1 CR78 Tamb. Crash 1 Cowbell 1 Crash 1 Cowbell 1 Ride Bell 1 Bongo3 High Bongo3 Low Cga Slap Cga Open Hi Cga Open Lo Timbale Timbale Agogo Agogo 626 Shaker Shaker 4 Soft Pad A Soft Pad B Long Guiro Long Guiro Claves Wood Block Wood Block Cuica Cuica Open Triangl Open Triangl Cabasa Cut REV Shaker 5 REV Shaker 4 REV Shaker 3 REV 626Shakr REV CR78Tamb REV Tamb.Lng REV Tamb.Sht REV Bongo3 H REV Bongo3 L REV F.Snap 3 REV F.Snaps2 REV HC2 Clp2 REV 707 Clps REV HC2 Clp1 R8 Click REV 909 Clp2

008 Demo Drum Old Kick Hybrid Kick1 Side Stick Loose Snr Tambrin MENU Natural SN2 Verb Tom Lo Cl HiHat 1 Verb Tom Lo Pedal HiHat Verb Tom Hi Op HiHat Verb Tom Hi Verb Tom Hi Crash 1 Verb Tom Hi Ride 1 China Cym Ride Bell 1 Tamb.Long Crash 1 Cowbell 1 Crash 1 Vibraslap Ride 2 Bongo Hi Bongo Lo Cga Mute Hi Cga Open Hi Cga Open Lo Timbale Timbale Agogo Agogo Cabasa Up Maracas Soft Pad A Soft Pad B Long Guiro Long Guiro Claves Wood Block Wood Block Shaker 3 Cuica 606 HiHat Cl Open Triangl 606 HiHat Op Ride 2 Dance Kick 2 Dance Kick 2 House Snr Tiny Snr 2 Tiny Snr 2 Hybrid Kick2 Old Kick Dance Kick 2 Loose Snr Natural SN2 Tiny Snr 2 Wind Chimes Dry Tom Lo Piccolo SN Dry Tom Lo

179

Appendices

Rhythm Set List

XP-C (WAVE EXPANSION C: Techno Collection)


001

Note No. TR-909 SET 35 Plastic BD 1 C2 36 37 38 39 40 41 43 44 45 46 47 C3 48 49 50 51 52 53 55 56 57 58 59 C4 60 61 62 63 64 65 67 68 69 70 71 C5 72 73 74 75 76 77 79 80 81 82 83 C6 84 85 86 87 88 89 91 92 93 94 95 C7 96 97 98 90 78 66 54 42


TR909 Kick 1 TR909 Rim TR909 Snr 5 TR909 Clap TR909 Snr 1 TR909 DstTom TR909 CHH 3 TR909 Tom TR909 OHH 3 TR909 DstTom TR909 OHH 3 TR909 Tom TR909 DstTom TR909 Crash TR909 Tom TR909 Ride TR909 Crash TR909 Ride Tambourine 2 TR909DsCrash TR808Cowbell TR606 Cym 1 PC-2 Machine TR707 Ride Mental Perc Dr.Beat Cga Open Hi Cga Mute Hi Cga Open Lo Timbale PC-2 Spacers TR727 Agogo TR727 Agogo TMB&SKR MENU TMB&SKR MENU Plastic BD 2 TR909 Kick 2 TR808 Rim TR909 Snr 1 CLAP MENU TR909 Snr 6 TR707 Tom TR909 CHH 3 TR707 Tom TR909 PHH 2 TR707 Tom TR909 OHH 1 Beam HiQ HIT MENU 1 May Day Perc Techno Scene Air Gun Tekno Hit Organ Hit 2 Analog Bird Retro UFO ElectronFall JP8000 FBK SNR MENU 2 TR808 Kick 1 KICK MENU 2 MC500 Beep 1 MC500 Beep 2

002 TR-808 SET TR808 Kick 1 TR808 Kick 1 TR808 Rim TR808 Snr 1 Clap Stop TR808 Snr 3 TR808 Tom TR808 CHH 1 TR808 Tom TR808 CHH 2 TR808 Tom OHH MENU TR808 Tom TR808 Tom TR606 Cym 1 TR808 Tom TR606 Cym 1 TR909 Crash TR909 Ride Tambourine 2 TR909 Crash TR808Cowbell TR606 Cym 1 TMB&SKR MENU TR707 Ride Mental Perc Dr.Beat Cga Open Hi Cga Mute Hi Cga Open Lo Timbale PC-2 Spacers TR727 Agogo TR727 Agogo Cabasa Up TMB&SKR MENU TR808 Kick 3 TR808 Kick 2 TR808 RimLng TR808 Snr 2 Clap Stop TR808 Snr 4 TR606 Tom TR808 CHH 2 TR606 Tom PHH MENU TR606 Tom OHH MENU Beam HiQ HIT MENU 1 May Day Perc Techno Scene Air Gun Tekno Hit White Noise ElectricDunk TR808 PHH SNR MENU 2 JP8000 FBK VOCODER MENU TR808 Kick 1 KICK MENU 2 MC500 Beep 1 MC500 Beep 2

003 TR-606 SET KICK MENU 1 TR606 Kick 1 TR808 Rim TR606 Snr 2 HC2 Dry Clap TR606 Snr 1 TR606 Tom TR606 CHH TR606 Tom PHH MENU TR606 Tom TR606 DstOHH TR606 Tom TR606 Tom TR606 Cym 2 TR606 Tom TR909 Ride TR606 Cym 1 TR707 Ride Tambourine TR909 Crash TR808Cowbell TR909 Crash TMB&SKR MENU TR707 Ride Mental Perc Dr.Beat Cga Open Hi Cga Mute Hi Cga Open Lo Timbale PC-2 Spacers TR727 Agogo TR727 Agogo Cabasa Up TMB&SKR MENU Plastic BD 1 Culture Kick TR808 Rim CR78 Snare TS Clap TR606 Snr 3 TR606 CmpTom CR78 CHH TR606 CmpTom TR606 PHH TR606 CmpTom CR78 OHH Beam HiQ HIT MENU 1 May Day Perc Techno Scene Air Gun Tekno Hit Organ Hit 2 Analog Bird Retro UFO ElectronFall JP8000 FBK SNR MENU 2 TR808 Kick 1 KICK MENU 2 MC500 Beep 1 MC500 Beep 2

004 Techno SET Plastic BD 1 TR909 Kick 1 TR909 Rim TR909 Snr 5 CLAP MENU TR909 Snr 6 TR909 Tom TR909 CHH 1 TR909 Tom TR909 PHH 2 TR909 Tom OHH MENU TR909 Tom TR909 Tom TR909 Crash TR909 Tom TR707 Ride TR909 Crash China Cym Tambourine 2 TR909 Crash TR707Cowbell TR606 Cym 1 TR808Cowbell TR606 Cym 1 PERCUSS MENU PERCUSS MENU PERCUSS MENU PERCUSS MENU PERCUSS MENU PERCUSS MENU PERCUSS MENU HIT MENU 1 HIT MENU 1 TechnoShaker Dance Shaker TR909 Kick 2 Plastic BD 2 COW&RIM MENU TR909 Snr 3 TR909 Clap TR909 Snr 4 TR909 DstTom TR909 CHH 3 TR909 DstTom TR909 PHH 1 TR909 DstTom TR909 OHH 3 Air Gun VOCODER MENU Beam HiQ VOCODER MENU May Day Perc VOCODER MENU VOCODER MENU Techno Scene VOCODER MENU Analog Bird VOCODER MENU 144:TeknoHAT 144:Tekno BD 120:TeknoBNG MC500 Beep 1 MC500 Beep 2

005 House SET TR909 Kick 1 Tekno Kick TR909 Rim DJ Snare TR909 Clap TR909 Snr 5 TR707 Tom TR909 CHH 1 TR707 Tom TR909 PHH 1 TR707 Tom OHH MENU TR707 Tom TR707 Tom TR909 Crash TR707 Tom TR909 Ride TR909 Crash Rattle Tamb Tambourine 2 TR909 Crash TR707Cowbell Crash 1 TR808Cowbell TR606 Cym 1 PERCUSS MENU PERCUSS MENU PERCUSS MENU PERCUSS MENU PERCUSS MENU PERCUSS MENU PERCUSS MENU HIT MENU 1 HIT MENU 1 Cabasa Up TechnoShaker Wet Kick Plastic BD 2 TR808 Rim SNR MENU 2 CLAP MENU SNR MENU 1 TR808 Tom TR707 CHH TR808 Tom TR707 PHH TR808 Tom OHH MENU Beam HiQ GTR FX MENU Org Chord GTR FX MENU Noisy 101 Claptail VOCODER MENU VOCODER MENU VOCODER MENU VOCODER MENU 120:House 1 120:House 2 120:House 3 120:TeknoBNG MC500 Beep 1 MC500 Beep 2

006 Jungle SET Tekno Kick JungleKick 2 Lo-Fi Snare Urban Snare SNR MENU 5 Jungle Snr 4 TR606 CmpTom CHH MENU 2 TR606 CmpTom Rattle Tamb TR606 CmpTom TR909 DstOHH TR606 CmpTom TR606 CmpTom R8 OHH TR606 CmpTom TR707 Ride TR909 Crash China Cym Tambourine 2 TR606 Cym 1 Cowbell 1 TR909 Crash MachineShout TR606 DstOHH PERCUSS MENU PERCUSS MENU PERCUSS MENU PERCUSS MENU PERCUSS MENU PERCUSS MENU PERCUSS MENU Surdo open Surdo mute TechnoShaker Dance Shaker KICK MENU 1 JungleKick 1 SideStiker MC Snare Comp Clap Ragga Snr 2 Jungle Snr 5 TR909 CHH 3 Jungle Snr 5 Tambourine 2 Jungle Snr 5 Cym OHH Beam HiQ HIT MENU 1 Thin Beef Analog Bird HIT MENU 2 Scratch Clap Emergency TR808Cowbell Talkbox Jungle Beep TR808 Kick 1 Roll Snare Roll Kick 160:DrumnBs MC500 Beep 1 MC500 Beep 2

007 Gabba SET Amsterdam BD TR909 Dst BD TR808 RimLng SNR MENU 1 Comp Clap SNR MENU 1 TR909 DstTom TR909 PHH 1 TR909 DstTom TR909 PHH 2 TR909 DstTom TR909 DstOHH TR909 DstTom TR909 DstTom TR909 Crash TR909 DstTom TR707 Ride TR909DsCrash China Cym CR78 CHH Crash 1 TR808Cowbell TR909DsCrash MachineShout TR606 Cym 2 PERCUSS MENU PERCUSS MENU PERCUSS MENU PERCUSS MENU PERCUSS MENU PERCUSS MENU PERCUSS MENU TR727 Agogo TR727 Agogo TechnoShaker Dance Shaker TR909 Dst BD KICK MENU 2 SideStiker Jungle Snr 4 CLAP MENU TR909 Snr 5 TR606 CmpTom TR909 CHH 3 TR606 CmpTom TR909 PHH 1 TR606 CmpTom TR909 OHH 1 Beam HiQ Air Gun ElectricDunk Thin Beef Drill Hit TAO Hit Daft Wave Thrill Emergency Dist TekGtr1 Dist Synth 120:House 1 120:House 3 184:Gabba MC500 Beep 1 MC500 Beep 2

008 Indust. SET INDUST. MENU INDUST. MENU Thrill PCM Press Air Gun PCM Press TekRok Snare TR909 CHH 3 TekRok Snare TR909 PHH 1 TekRok Snare TR909 DstOHH TekRok Snare TekRok Snare Indus Snare TekRok Snare TR909 Ride Drill Hit ElectricDunk PCM Press TR606 Cym 1 PC-2 Machine TR909 Crash Crash 1 TR606 DstCym PERCUSS MENU PERCUSS MENU PERCUSS MENU PERCUSS MENU PERCUSS MENU PERCUSS MENU PERCUSS MENU Analog Bird Analog Bird TechnoShaker Dance Shaker TR909 Dst BD Turbo Kick Drill Hit SNR MENU 3 INDUST. MENU Rage Snare Can Tom HIT MENU 1 Can Tom Beam HiQ Can Tom TR909 DstOHH Beam HiQ VOCODER MENU TR606 Cym 1 VOCODER MENU CLAP MENU VOCODER MENU VOCODER MENU Roll Kick Organ Hit 2 Roll Snare TR909 DstOHH Roll Kick TR909DsCrash CLAP MENU MC500 Beep 1 MC500 Beep 2

180

Performance List
USER (User Group)
No. 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Name EasternSplit Opening Orch Feedback EP Humming Vox Tekno Loop 1 Fr.Horn Sect SpaceCarrier Orchestral Nebular Vox Terminator Flying Jazz Sweeper Rave Split Multi Sax Cosmic Dawn Bass / Lead S&H / Pad AcPiano+Pad Kicks Attack Step Brass Drone / Pipe Chime Dreams Tekno Loop 2 Big Band Labyrinth White Hole Cyber Sweep Tekno Asia 1080 Fantasy Pop Ballad Rhythmatic Power JV Key Mode LAYER LAYER LAYER LAYER LAYER LAYER LAYER LAYER LAYER LAYER LAYER LAYER LAYER LAYER LAYER LAYER LAYER LAYER LAYER LAYER LAYER LAYER LAYER LAYER LAYER LAYER LAYER LAYER LAYER LAYER LAYER LAYER

PR-A (Preset A Group)


No. 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Name House Set Analectro Anatronic Tekno Pop 1 Tekno Pop 2 Hard Core Hi Energy Pop Dance Acid Set Ambient Set Electro Pop Pop Set 1 Pop Set 2 Pop Set 3 Pop Set 4 L.A. Ballad Hip Hop Set Funk Rock Funk Fusion Heavy Metal Heavy Kids Latin Set BrazilianSet New Age 1 New Age 2 Orchestra Concerto Film Score 1 Film Score 2 Symphonic Chamber Set Baroque Set Key Mode SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE LAYER SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE

PR-B (Preset B Group)


No. 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Name Africa World Ethnic Asian Ethnic Asian Band 60s Set Blues Band Country Band Folk Set Reggae Band FunkWah Band FunkinPhaze Zydeco Band New Orleans Dixieland Big Band Set Cont.Jazz 1 Cont.Jazz 2 Ac.Jazz Set Gospel Set All Strings All Brass All Piano 1 All Piano 2 All Keyboard All Organ All Winds All Bells Mlt & Perc All Seq All Bass All Pad All FX Key Mode SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE SINGLE LAYER SINGLE SINGLE SINGLE SINGLE SINGLE

181

Appendices

Arpeggio Style List


Style 1/4 1/6 1/8 1/12 1/16 1/32 Motif all all all all all SINGLE UP, SINGLE DOWN, SINGLE UP&DOWN, SINGLE RANDOM, DUAL UP, DUAL DOWN, DUAL UP&DOWN, DUAL RANDOM, NOTE ORDER, GLISSANDO, BASS+UP 18, BASS+RANDOM 13, TOP+UP 16 all all GLISSANDO all all SINGLE UP, SINGLE DOWN, SINGLE UP&DOWN, SINGLE RANDOM, DUAL UP, DUAL DOWN, DUAL UP&DOWN, DUAL RANDOM, NOTE ORDER, GLISSANDO, BASS+UP 18, BASS+RANDOM 13, TOP+UP 16 all SINGLE UP, SINGLE DOWN, SINGLE UP&DOWN, SINGLE RANDOM, DUAL UP, DUAL DOWN, DUAL UP&DOWN, DUAL RANDOM, NOTE ORDER BASS+UP 2 BASS+UP 5, TOP+UP 5 BASS+UP 5, TOP+UP 5 SINGLE UP, SINGLE DOWN, SINGLE UP&DOWN, SINGLE RANDOM, NOTE ORDER, GLISSANDO SINGLE UP, SINGLE DOWN, SINGLE UP&DOWN, SINGLE RANDOM, DUAL UP, DUAL DOWN, DUAL UP&DOWN, DUAL RANDOM, NOTE ORDER, BASS+UP 18, BASS+RANDOM 13, TOP+UP 16 CHORD CHORD CHORD SINGLE UP, SINGLE DOWN BASS+UP+TOP SINGLE UP, SINGLE DOWN CHORD BASS+CHORD 4, BASS+CHORD 5 BASS+CHORD 2, BASS+UP 2, BASS+RANDOM 2, TOP+UP 2 BASS+CHORD 2, BASS+UP 2, BASS+RANDOM 2, TOP+UP 2 CHORD, BASS+CHORD 1 SINGLE UP, SINGLE DOWN, SINGLE UP&DOWN, SINGLE RANDOM, DUAL UP, DUAL DOWN, DUAL UP&DOWN, DUAL RANDOM, NOTE ORDER, BASS+UP 18, BASS+RANDOM 13, TOP+UP 16 SINGLE UP, SINGLE DOWN, SINGLE UP&DOWN, GLISSANDO TOP+UP 46 SINGLE UP, SINGLE DOWN, SINGLE UP&DOWN, SINGLE RANDOM, DUAL UP, DUAL DOWN, DUAL UP&DOWN, DUAL RANDOM, NOTE ORDER, GLISSANDO SINGLE RANDOM, DUAL RANDOM, BASS+RANDOM 13 all all all SINGLE UP, SINGLE DOWN, SINGLE UP&DOWN, SINGLE RANDOM, DUAL UP, DUAL DOWN, DUAL UP&DOWN, DUAL RANDOM, NOTE ORDER, GLISSANDO all all all all Beat Pattern 1/ 4 1/ 6 1/ 8 1/12 1/16 13 1/32 13 Accent Rate Shuffle Rate 0100% 0100% 0100% 0100% 0100% 0100% 5090% 5090% 5090% 5090% 5090% 5090%

PORTAMENTO A PORTAMENTO B GLISSANDO SEQUENCE A SEQUENCE B SEQUENCE C

PORTA-A 0111 PORTA-B 0115 1/16 13, 1/32 13 SEQ-A 17 SEQ-B 15 SEQ-C 12

0100% 0100% 0100% 0100% 0100% 0100%

5090% 5090% 5090% 5090% 5090% 5090%

SEQUENCE D ECHO

SEQ-D 18 ECHO 13

0100% 0100%

5090% 5090%

SYNTH BASS SLAP BASS A SLAP BASS B WALK BASS RHYTHM GTR A

SEQ-A 1, SEQ-C 1 MUTE 02, 03 MUTE 02, 03 WALKBS, REFRAIN 1 MUTE 01,04

0100% 0100% 0100% 0100% 0100%

5090% 5090% 5090% 5090% 5090%

RHYTHM GTR B RHYTHM GTR C RHYTHM GTR D RHYTHM GTR E 3 FINGER GTR STRUMMING GTR KBD COMPING A KBD COMPING B KBD COMPING C KBD COMPING D KBD COMPING E PERCUSSION

MUTE 07, 13, 14 MUTE 08, 12, 15 MUTE 09, 10, 11, 16 STRUM 16 SEQ-A 7 STRUM 7, 8 MUTE 12, REFRAIN 2 MUTE 05, 06 1/ 6, 1/12 1/16 13 REGGAE12 PERC14

0100% 0100% 0100% 0100% 0100% 0100% 0100% 0100% 0100% 0100% 0100% 0100%

5090% 5090% 5090% 5090% 5090% 5090% 5090% 5090% 5090% 5090% 5090% 5090%

HARP SHAMISEN BOUND BALL

HARP SEQ-A 2 BOUND

0100% 0100% 0100%

5090% 5090% 5090%

RANDOM BOSSA NOVA SALSA MAMBO LATIN PERCUSSION

1/ 4, 1/6, 1/8, 1/12, 1/16 13, 1/32 13, RANDOM BOSSA NOVA SALSA 14 MAMBO 12 CLAVE, REV CLA, GUIRO, AGOGO

0100% 0100% 0100% 0100% 0100%

5090% 5090% 5090% 5090% 5090%

SAMBA TANGO HOUSE LIMITLESS

SAMBA TANGO 14 HOUSE 12 all

0100% 0100% 0100% 0100%

5090% 5090% 5090% 5090%

all: there is no restriction on the value which can be set

182

MIDI Implementation
Model: Version: Date: XP-30 (64 Voice Expandable Synthesizer) 1.00 Jan. 18 1999 * The Patches corresponding to each Bank Select are as follows.

1. Data Reception (sound source section)


s Channel Voice Messages
q Note Off
status 2nd byte 3rd byte 8nH kkH vvH 9nH kkH 00H n=MIDI channel number: 0H - FH (ch.1 - ch.16) kk=note number: 00H - 7FH (0 - 127) vv=Note Off velocity: 00H - 7FH (0 - 127) * * Not received in Performance mode when the Rx parameter (PERFORM/MIDI/MIDI) is OFF. Not received by the Rhythm Part (Part 10) when the Env Mode parameter (RHYTHM/ CONTROL/CONTROL) is NO-SUS.

Bank Select | Program No | Group Patch No. MSB | LSB | | +++ 80 | 0 | 0 - 127 | User 1 - 128 81 | 0 | 0 - 127 | PR-A 1 - 128 81 | 1 | 0 - 127 | PR-B 1 - 128 81 | 2 | 0 - 127 | PR-C 1 - 128 81 | 3 | 0 - 127 | GM 1 - 128 81 | 4 | 0 - 127 | PR-E 1 - 128 84 | 0 | 0 - 127 | XP-A (Session) 1 - 128 84 | 1 | 0 - 126 | XP-A 129 - 255 84 | 2 | 0 - 127 | XP-B (Orchestral) 1 - 128 84 | 3 | 0 - 126 | XP-B 129 - 255 84 | 4 | 0 - 127 | XP-C (Techno Collection) 1 - 128 84 | 5 | 0 - 127 | XP-C 129 - 256 84 | 6 | 0 - 127 | XP-D 1 - 128 84 | 7 | 0 - 127 | XP-D 129 - 256 84 | 8 | 0 - 127 | XP-E 1 - 128 84 | 9 | 0 - 127 | XP-E 129 - 256 * The Performance corresponding to each Bank Select are as follows.

Bank Select | Program No | Group Performance No. MSB | LSB | | +++ 80 | 0 | 0 - 31 | User 1 - 32 81 | 0 | 0 - 31 | PR-A 1 - 32 81 | 1 | 0 - 31 | PR-B 1 - 32 * The Rhythm set corresponding to each Bank Select are as follows.

q Note On
status 2nd byte 3rd byte 9nH kkH vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) kk=note number: 00H - 7FH (0 - 127) vv=Note On velocity: 01H - 7FH (1 - 127) * Not received in Performance mode when the Rx parameter (PERFORM/MIDI/MIDI) is OFF.

q Polyphonic Aftertouch
status 2nd byte 3rd byte AnH kkH vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) kk=note number: 00H - 7FH (0 - 127) vv=Aftertouch: 00H - 7FH (0 - 127) * * * This message is received if the Aftertouch parameter (SYSTEM/CONTROL/CONTROL SOURCE) is POLY or CH&POLY. Not received in Performance mode when the Rx parameter (PERFORM/MIDI/MIDI) is OFF. Not received in GM mode.

Bank Select | Program No | Group Rhythm set No. MSB | LSB | | +++ 80 | 0 | 0 - 1 | User 1 - 2 81 | 0 | 0 - 1 | PR-A 1 - 2 81 | 1 | 0 - 1 | PR-B 1 - 2 81 | 2 | 0 - 1 | PR-C 1 - 2 81 | 3 | 0 - 1 | GM 1 - 2 81 | 4 | 0 - 1 | PR-E 1 - 2 84 | 0 | 0 - 7 | XP-A (Session) 1 - 8 84 | 4 | 0 - 7 | XP-C (Techno Collection) 1 - 8 84 | 6 | 0 - 127 | XP-D 1 - 128 84 | 7 | 0 - 127 | XP-D 129 - 256 84 | 8 | 0 - 127 | XP-E 1 - 128 84 | 9 | 0 - 127 | XP-E 129 - 256

Modulation (Controller number 1)


status 2nd byte 3rd byte BnH 01H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=Modulation depth: 00H - 7FH (0 - 127)

Breath Type (Controller number 2)


status 2nd byte 3rd byte BnH 02H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 7FH (0 - 127)

q Control Change
* If the corresponding Controller number is selected for the Control 2 or Control 3 parameter (PATCH/CONTROL/CONTROL SOURCE), the corresponding effect will occur. If a Controller number that corresponds to the Control 1 parameter or Control 2 parameter (SYSTEM/CONTROL/SYS-CTRL ASSIGN) is selected, the specified effect will apply if Control 2 parameter or Control 3 parameter (PATCH/CONTROL/ CONTROL SOURCE) is set to SYS-CTRL1 or SYS-CTRL2. Not received in Performance mode when the Rx parameter (PERFORM/MIDI/MIDI) or the Control Change Receive Switch is OFF.

Foot Type (Controller number 4)


status 2nd byte 3rd byte BnH 04H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 7FH (0 - 127)

Portamento Time (Controller number 5)


status 2nd byte 3rd byte BnH 05H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=Portamento Time: 00H - 7FH (0 - 127) * The Time parameter (PATCH/CONTROL/PORTAMENTO) will change.

Bank Select (Controller number 0,32)


status 2nd byte 3rd byte BnH 00H mmH BnH 20H llH n=MIDI channel number: 0H - FH (ch.1 - ch.16) mm,ll=Bank number: 00 00H - 7F 7FH (bank.1 - bank.16384) * * Not received when the Program Change parameter or Bank Select parameter (SYSTEM/ MIDI/RECEIVE MIDI) is OFF. Not received in GM mode.

Data Entry (Controller number 6, 38)


status 2nd byte 3rd byte BnH 06H mmH BnH 26H llH n=MIDI channel number: 0H - FH (ch.1 - ch.16) mm,ll= the value of the parameter specified by RPN/NRPN mm=MSB, ll=LSB

Volume (Controller number 7)


status 2nd byte 3rd byte BnH 07H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=Volume: 00H - 7FH (0 - 127)

183

Appendices

MIDI Implementation

Balance (Controller number 8)


status 2nd byte 3rd byte BnH 08H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=Balance: 00H - 7FH (0 - 127)

Sound Controller 3 (Controller number 72)


status 2nd byte 3rd byte BnH 48H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 40H - 7FH (-128 - 0 - +126) * The T24 parameter (PATCH/TVF/TVF ENVELOPE), The T24 parameter (PATCH/ TVA/TVA ENVELOPE) will change relatively.

Panpot (Controller number 10)


status 2nd byte 3rd byte BnH 0AH vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=Panpot: 00H - 40H - 7FH (left - center - right) * Adjust the stereo location over 128 steps, where 0 is far left, 64 is center, and 127 is far right. However this is not received when the Pan parameter (PATCH/CONTROL/ RxSWITCH) is OFF.

Sound Controller 4 (Controller number 73)


status 2nd byte 3rd byte BnH 49H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 40H - 7FH (-128 - 0 - +126) * The T1 parameter (PATCH/TVF/TVF ENVELOPE), The T1 parameter (PATCH/TVA/ TVA ENVELOPE) will change relatively.

Expression (Controller number 11)


status 2nd byte 3rd byte BnH 0BH vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=Expression: 00H - 7FH (0 - 127) * If the Volume parameter (SYSTEM/CONTROL/CONTROL SOURCE) is set to VOL&EXP, the volume of the Part corresponding to the MIDI channel of the received message will be adjusted. However this is not received if the Volume parameter (PATCH/CONTROL/RxSWITCH) is OFF. In GM mode, the volume can always be controlled.

Sound Controller 5 (Controller number 74)


status 2nd byte 3rd byte BnH 4AH vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 40H - 7FH (-64 - 0 - +63) * The Cut parameter (PATCH/TVF/FILTER) will change relatively.

General Purpose Controller 5 (Controller number 80)


status 2nd byte 3rd byte BnH 50H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 40H - 7FH (-128 - 0 - +126) * The L13 parameter (PATCH/TVA/TVA ENVELOPE) of Tone 1 will change relatively.

Hold 1 (Controller number 64)


status 2nd byte 3rd byte BnH 40H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON * Not received when the Hold-1 RxSwitch parameter (PATCH/CONTROL/DAMPER) is OFF.

General Purpose Controller 6 (Controller number 81)


status 2nd byte 3rd byte BnH 51H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 40H - 7FH (-128 - 0 - +126) * The L13 parameter (PATCH/TVA/TVA ENVELOPE) of Tone 2 will change relatively.

Portamento (Controller number 65)


status 2nd byte 3rd byte BnH 41H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON * The Sw parameter (PATCH/CONTROL/PORTAMENTO) will change.

General Purpose Controller 7 (Controller number 82)


status 2nd byte 3rd byte BnH 52H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 40H - 7FH (-128 - 0 - +126) * The L13 parameter (PATCH/TVA/TVA ENVELOPE) of Tone 3 will change relatively.

Sostenuto (Controller number 66)


status 2nd byte 3rd byte BnH 42H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON

General Purpose Controller 8 (Controller number 83) Soft (Controller number 67)
status 2nd byte 3rd byte BnH 43H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON status 2nd byte 3rd byte BnH 53H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 40H - 7FH (-128 - 0 - +126) * The L13 parameter (PATCH/TVA/TVA ENVELOPE) of Tone 4 will change relatively.

Hold 2 (Controller number 69)


status 2nd byte 3rd byte BnH 45H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 7FH (0 - 127) * A hold movement isn't done. * A Note On message received immediately after a Portamento control will be sounded with the pitch changing smoothly from the source note number. If a voice is already sounding at the same note number as the source note number, that voice will change pitch to the pitch of the newly received Note On, and continue sounding (i.e., will be played legato). The speed of the pitch change caused by Portamento is determined by the Time parameter (PATCH/CONTROL/PORTAMENTO) value.

Portamento Control (Controller number 84)


status 2nd byte 3rd byte BnH 54H kkH n=MIDI channel number: 0H - FH (ch.1 - ch.16) kk=source note number: 00H - 7FH (0 - 127)

Sound Controller 2 (Controller number 71)


status 2nd byte 3rd byte BnH 47H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 40H - 7FH (-128 - 0 - +126) * The Res parameter (PATCH/TVF/FILTER) will change relatively.

184

MIDI Implementation

Effect 1 (Reverb Send Level) (Controller number 91)


status 2nd byte 3rd byte BnH 5BH vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=Reverb Send Level: 00H - 7FH (0 - 127) * In Performance mode, the Reverb Send Level parameter of each Part will change.

Program Change
status 2nd byte CnH ppH n=MIDI channel number: 0H - FH (ch.1 - ch.16) pp=Program number: 00H - 7FH (prog.1 - prog.128) * * * Not received when the Program Change parameter (SYSTEM/MIDI/RECEIVE MIDI) is OFF. When received on the Control channel, the Performance will change. Not received in Performance mode when the Rx parameter (PERFORM/MIDI/MIDI) is OFF.

Effect 3 (Chorus Send Level) (Controller number 93)


status 2nd byte 3rd byte BnH 5DH vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=Chorus Send Level: 00H - 7FH (0 - 127) * In Performance mode, the Chorus Send Level parameter of each Part will change.

Channel Aftertouch
status 2nd byte DnH vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=Channel Aftertouch: 00H - 7FH (0 - 127) * Not received in Performance mode when the Rx parameter (PERFORM/MIDI/MIDI) is OFF.

RPN MSB/LSB (Controller number 100, 101)


status 2nd byte 3rd byte BnH 65H mmH BnH 64H llH n=MIDI channel number: 0H - FH (ch.1 - ch.16) mm=MSB of the parameter number specified by RPN ll=LSB of the parameter number specified by RPN <<< RPN >>> Control Changes include RPN (Registered Parameter Numbers), which are extended parameters whose function is defined in the MIDI specification. When using RPNs, first the RPN (Controller numbers 100 and 101; they can be sent in any order) is transmitted to specify the parameter you wish to control. Then, Data Entry messages (Controller numbers 6 and 38) are used to set the value of the specified parameter. Once a RPN parameter has been specified, all further Data Entry messages on that channel are considered to apply to that specified parameter. In order to prevent accidents, when the desired setting has been made for the parameter, it is recommended that RPN be set to Null. This device receives the following RPNs. RPN MSB LSB 00H 00H Data entry MSB LSB mmH -

Pitch Bend Change


status 2nd byte 3rd byte EnH llH mmH n=MIDI channel number: 0H - FH (ch.1 - ch.16) mm,ll=Pitch Bend value: 00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191) * Not received in Performance mode when the Rx parameter (PERFORM/MIDI/MIDI) is OFF.

Channel Mode Messages


All Sound Off (Controller number 120)
status BnH n=MIDI channel: * * 2nd byte 78H 3rd byte 00H 0H - FH (ch.1 - ch.16)

Notes Pitch Bend Sensitivity mm : 00H - 0CH (0 - 12 semitones) ll : ignored (processed as 00H) Up to 1 octave can be specified in semitone steps. *The Bend Range parameter (PATCH/ CONTROL/KEY MODE & BENDER) will also be changed. *Not received by the Rhythm Part (Part 10). Channel Fine Tuning mm, ll : 20 00H - 40 00H - 60 00H ( -4096 x 100 / 8192 - 0 - +4096 x 100 / 8192 cent ) *In Patch mode, the Master parameter (SYSTEM/TUNE/TUNE) will change. *In Performance mode, the Fine parameter (PERFORM/PART/SETTING) of each Part will change. When received on the Control channel, the Master parameter (SYSTEM/ TUNE/TUNE) will change. Channel Coarse Tuning mm : 10H - 40H - 70H (-48 - 0 - +48 semitones) ll : ignored (processed as 00H) *Not received in Patch mode. *In Performance mode, the Coarse parameter (PERFORM/PART/SETTING) of each Part will change. RPN null RPN and NRPN will be set as unspecified. Once this setting has been made, subsequent Data Entry messages will be ignored. (It is not necessary to transmit Data Entry for RPN Null settings. Parameter values that were previously set will not change. mm, ll: ignored

When this message is received, all notes currently sounding on the corresponding channel will be turned off. Not received in Performance mode when the Rx parameter (PERFORM/MIDI/MIDI) is OFF.

Reset All Controllers (Controller number 121)


status 2nd byte 3rd byte BnH 79H 00H n=MIDI channel number: 0H - FH (ch.1 - ch.16) * * Not received in Performance mode when the Rx parameter (PERFORM/MIDI/MIDI) is OFF. When this message is received, the following controllers will be set to their reset values. Reset value [+-]0 (center) 0 (off) 0 (off) 0 (off) 0 (minimum) 127 (maximum) However the controller will be at minimum. 0 (off) 0 (off) 0 (off) 0 (off) Unset. Previously set data will not change. Unset. Previously set data will not change. (minimum) (minimum)

00H 01H

mmH llH

00H 02H

mmH -

Controller Pitch Bend Change Polyphonic Key Pressure Channel Pressure Modulation Breath type Expression Hold 1 Sostenuto Soft Hold 2 RPN NRPN System General purpose controller 10 System General purpose controller 20

7FH 7FH

--

185

Appendices

MIDI Implementation

q All Note Off (Controller number 123)


status 2nd byte 3rd byte BnH 7BH 00H n=MIDI channel number: 0H - FH (ch.1 - ch.16) * When All Note Off is received, all currently sounding notes of the corresponding channel will be turned off. However if Hold 1 or Sostenuto are on, the sound will be held until these are turned off. Not received in Performance mode if Rx parameter (PERFORM/MIDI/MIDI) is OFF.

s System Exclusive Messages


status F0H F0H: ii = ID number: data byte iiH, ddH, ......, eeH status F7H

q Omni Off (Controller number 124)


status 2nd byte 3rd byte BnH 7CH 00H n=MIDI channel number: 0H - FH (ch.1 - ch.16) * * The same processing as when All Note Off is received will be done. Not received in Performance mode if Rx parameter (PERFORM/MIDI/MIDI) is OFF.

dd,..., ee = data: F7H:

System Exclusive message status This is the ID number (manufacturer ID) that specifies the manufacturer whose exclusive message this is. Roland's manufacturer ID is 41H.ID numbers 7EH and 7FH are defined in an expansion of the MIDI standard as Universal Non-realtime messages (7EH) and Universal Realtime Messages (7FH). 00H - 7FH (0 - 127) EOX (End Of Exclusive)

Of the System Exclusive messages received by this device, the Universal Non-realtime messages and the Universal Realtime messages and the Data Request (RQ1) messages and the Data Set (DT1) messages will be set automatically.

q Universal Non-realtime System Exclusive Messages


Identity Request Message
When this message is received, Identity Reply message (p. 189) will be transmitted. status F0H Byte F0H 7EH dev 06H 01H F7H * data byte status 7EH, dev, 06H, 01H F7H Remarks Exclusive status ID number device ID sub ID#1 sub ID#2 EOX

q Omni On (Controller number 125)


status 2nd byte 3rd byte BnH 7DH 00H n=MIDI channel number: 0H - FH (ch.1 - ch.16) * * The same processing as when All Note Off is received will be done. The instrument will not be set to OMNI ON. Not received in Performance mode if Rx parameter (PERFORM/MIDI/MIDI) is OFF.

q Mono (Controller number 126)


status 2nd byte 3rd byte BnH 7EH mmH n=MIDI channel number: 0H - FH (ch.1 - ch.16) mm=Mono number: 00H - 10H (0 - 16) * * The same processing as when All Note Off is received will be done, and the Assign parameter (PATCH/CONTROL/KEY MODE & BENDER) will be set to SOLO. Not received in Performance mode if Rx parameter (PERFORM/MIDI/MIDI) is OFF.

(Universal Non-realtime message) (dev: 10H - 1FH) (General Information) (Identity Request) (End Of Exclusive)

The dev is own device number or 7FH (Broadcast).

GM System On
GM System On is a command message that resets the internal settings of the instrument to the GM initial state (General MIDI System - Level 1). A GM instrument that receives this message will automatically enter a state in which it can correctly perform a GM score. status F0H Byte F0H 7EH 7FH 09H 01H F7H * data byte status 7EH, 7FH, 09H, 01H F7H Remarks Exclusive status ID number device ID sub ID#1 sub ID#2 EOX

q Poly (Controller number 127)


status 2nd byte 3rd byte BnH 7FH 00H n=MIDI channel number:0H - FH (ch.1 - ch.16) * * The same processing as when All Note Off is received will be done, and the Assign parameter (PATCH/CONTROL/KEY MODE & BENDER) will be set to POLY. Not received in Performance mode if Rx parameter (PERFORM/MIDI/MIDI) is OFF.

s System Realtime Messages


q Timing Clock
status F8H * This message will be received if the Clock Source parameter (SYSTEM/SETUP/SYSTEM SETUP) is MIDI (p. 129).

(Universal Non-realtime message) (Broadcast) (General MIDI Message) (General MIDI On) (End Of Exclusive)

Not received when the Rx.GM parameter (SYSTEM/MIDI/SYS-EXC MIDI) is OFF.

GM System Off
When this messages is received, this instrument will return to the performance mode. status F0H Byte F0H 7EH 7FH 09H 02H F7H * data byte status 7EH, 7FH, 09H, 02H F7H Remarks Exclusive status ID number device ID sub ID#1 sub ID#2 EOX

q Active Sensing
status FEH * When an Active Sensing message is received, the unit will begin monitoring the interval at which MIDI messages are received. During monitoring, if more than 420 ms passes without a message being received, the same processing will be done as when All Sound Off, All Note Off, and Reset All Controllers messages are received. Then monitoring will be halted.

(Universal Non-realtime message) (Broadcast) (General MIDI Message) (General MIDI Off) (End Of Exclusive)

Not received when the Rx.GM parameter (SYSTEM/MIDI/SYS-EXC MIDI) is OFF.

186

MIDI Implementation

q Universal Realtime System Exclusive messages


Master Volume
status F0H Byte F0H 7FH 7FH 04H 01H llH mmH F7H * * * data byte 7FH, 7FH, 04H, 01H, llH, mmH status F7H

Data Set 1

DT1

This message transmits the actual data, and is used when you wish to set the data of the receiving device. status F0H data byte 41H, dev, 6AH, 12H, aaH, bbH, ccH, ddH, eeH, ... ffH, sum Remarks Exclusive status ID number device ID model ID command ID address MSB address address address LSB data: : data checksum EOX (Roland) (dev: 10H - 1FH) (XP-30) (DT1) status F7H

Remarks Exclusive status ID number (Universal Realtime message) device ID (Broadcast) sub ID#1 (Device Control Message) sub ID#2 (Master Volume) LSB of Master Volume MSB of Master Volume EOX (End Of Exclusive)

LSB of Master Volume (llH) is processed as 00H. This message is not received if the Rx.Exc parameter (SYSTEM/MIDI/SYS-EXC MIDI) is OFF. This message is not received in GM mode.

Byte F0H 41H dev 6AH 12H aaH bbH ccH ddH eeH : ffH sum F7H *

The actual data to be transmitted. Multi-byte data is transmitted in the order of the address.

q Data Transmission
This instrument can use exclusive messages to exchange many varieties of internal settings with other devices. The model ID of the exclusive messages used by this instrument is 6AH.

(End Of Exclusive)

Data Request 1 RQ1


This message requests the other device to transmit data. The address and size indicate the type and amount of data that is requested. When a Data Request message is received, if the device is in a state in which it is able to transmit data, and if the address and size are appropriate, the requested data is transmitted as a Data Set 1 (DT1) message. If the conditions are not met, nothing is transmitted. status F0H data byte 41H, dev, 6AH, 11H, aaH, bbH, ccH, ddH, ssH, ttH, uuH, vvH, sum Remarks Exclusive status ID number device ID model ID command ID address MSB address address address LSB size MSB size size size LSB checksum EOX status F7H

* * *

The amount of data that is transmitted at one time is fixed for the type of data, and only data of the fixed starting address and size will be transmitted. Refer to the address and size given in Parameter Address Map (p. 190). Data whose size is greater than 128 bytes should be divided into packets of 128 bytes or less and transmitted. Successive Data Set 1 messages should have at least 20 ms of time interval between them. For the checksum, refer to (p. 204). This message is not received if Rx.Exc parameter (SYSTEM/MIDI/SYS-EXC MIDI) is OFF. This message is not received in GM mode.

This device is able to receive GS Exclusive messages only for Scale Tune settings.

Data Set 1
Byte F0H 41H dev 6AH 11H aaH bbH ccH ddH ssH ttH uuH vvH sum F7H *

DT1

(Roland) (dev: 10H - 1FH) (XP-30) (RQ1)

This message transmits the actual data, and is used when you wish to set the data of the receiving device. status F0H data byte 41H, dev, 42H, 12H, aaH, bbH, ccH, ddH, ... eeH, sum Remarks Exclusive status ID number device ID model ID command ID address MSB address middle byte address LSB data: : data checksum EOX status F7H

(End Of Exclusive)

Byte F0H 41H dev 42H 12H aaH bbH ccH ddH : eeH sum F7H * *

(Roland) (dev: 10H - 1FH) (GS) (DT1)

* * *

The size of data that can be transmitted at one time is fixed for each type of data. and data requests must be made with a fixed starting address and size. Refer to the address and size given in Parameter Address Map (p. 190). For the checksum, refer to (p. 204). This message is not received if the Rx.Exc parameter (SYSTEM/MIDI/SYS-EXC MIDI) is OFF. This message is not received in GM mode.

The actual data to be transmitted. Multi-byte data is transmitted in the address order.

(End Of Exclusive)

187

Appendices

This message is not received when the Rx.Exc parameter (SYSTEM/MIDI/SYS-EXC MIDI) is OFF. This message is not received in GM mode.

MIDI Implementation

2. Data transmission (sound source section)


s Channel Voice Messages
q Note Off
status 2nd byte 3rd byte 8nH kkH vvH n=MIDI channel: 0H - FH (ch.1 - ch.16) kk=Note Number: 00H - 7FH (0 - 127) vv=Note Off Velocity: 00H - 7FH (0 - 127)

Panpot (Controller number 10)


status 2nd byte 3rd byte BnH 0AH vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=panpot: 00H - 40H - 7FH (left - center - right)

Expression (Controller number 11)


status 2nd byte 3rd byte BnH 0BH vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=Expression: 00H - 7FH (0 - 127)

q Note On
status 2nd byte 3rd byte 9nH kkH vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) kk=note number: 00H - 7FH (0 - 127) vv=Note On velocity: 01H - 7FH (1 - 127)

Hold 1 (Controller number 64)


status 2nd byte 3rd byte BnH 40H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON

Portamento (Controller number 65)


status 2nd byte 3rd byte BnH 41H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON

q Control Change
* By selecting a controller number that corresponds to the setting of the Assign parameter (SYSTEM/CONTROL/CONTROL PEDAL) or each Assign parameter of C14 Slider (SYSTEM/CONTROL/ASSIGN), you can transmit any desired control change.

Bank Select (Controller number 0,32)


status 2nd byte 3rd byte BnH 00H mmH BnH 20H llH n=MIDI channel number: 0H - FH (ch.1 - ch.16) mm,ll=Bank number: 00 00H - 7F 7FH (bank.1 - bank.16384) * * * This message is not transmitted if Program parameter (SYSTEM/MIDI/TRANSMIT MIDI) or Bank Sel parameter (SYSTEM/MIDI/TRANSMIT MIDI) is OFF. For the Bank Select that corresponds to each Patch, refer to section 1. This message is not transmitted in GM mode

Sostenuto (Controller number 66)


status 2nd byte 3rd byte BnH 42H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON

Soft (Controller number 67)


status 2nd byte 3rd byte BnH 43H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON

Modulation (Controller number 1)


status 2nd byte 3rd byte BnH 01H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=Modulation Depth: 00H - 7FH (0 - 127)

Hold 2 (Controller number 69)


status 2nd byte 3rd byte BnH 45H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 7FH (0 - 127)

Breath type (Controller number 2)


status 2nd byte 3rd byte BnH 02H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 7FH (0 - 127)

Sound Controller 2 (Controller number 71)


status 2nd byte 3rd byte BnH 47H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 40H - 7FH (-128 - 0 - +126)

Foot Type (Controller number 4)


status 2nd byte 3rd byte BnH 04H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 7FH (0 - 127)

Sound Controller 3 (Controller number 72)


status 2nd byte 3rd byte BnH 48H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 40H - 7FH (-128 - 0 - +126)

Portamento Time (Controller number 5)


status 2nd byte 3rd byte BnH 05H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=Portamento Time: 00H - 7FH (0 - 127)

Sound Controller 4 (Controller number 73)


status 2nd byte 3rd byte BnH 49H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 40H - 7FH (-128 - 0 - +126)

Volume (Controller number 7)


status 2nd byte 3rd byte BnH 07H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=Volume: 00H - 7FH (0 - 127)

Sound Controller 5 (Controller number 74)


status 2nd byte 3rd byte BnH 4AH vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 40H - 7FH (-64 - 0 - +63)

Balance (Controller number 8)


status 2nd byte 3rd byte BnH 08H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=Balance: 00H - 7FH (0 - 127)

General Purpose Controller 5 (Controller number 80)


status 2nd byte 3rd byte BnH 50H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 40H - 7FH (-128 - 0 - +126)

188

MIDI Implementation

General Purpose Controller 6 (Controller number 81)


status 2nd byte 3rd byte BnH 51H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 40H - 7FH (-128 - 0 - +126)

Pitch Bend Change


status 2nd byte 3rd byte EnH llH mmH n=MIDI channel number: 0H - FH (ch.1 - ch.16) mm,ll=Pitch Bend value: 00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)

General Purpose Controller 7 (Controller number 82)


status 2nd byte 3rd byte BnH 52H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 40H - 7FH (-128 - 0 - +126)

System Realtime Messages


Active Sensing
status FEH * * Transmitted at intervals of approximately 250ms. Not transmitted if the Active Sensing parameter (SYSTEM/MIDI/TRANSMIT MIDI) is OFF.

General Purpose Controller 8 (Controller number 83)


status 2nd byte 3rd byte BnH 53H vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=control value: 00H - 40H - 7FH (-128 - 0 - +126)

Portamento Control (Controller number 84)


status 2nd byte 3rd byte BnH 54H kkH n=MIDI channel number: 0H - FH (ch.1 - ch.16) kk=source note number: 00H - 7FH (0 - 127)

System Exclusive Messages


There is a kind of the Universal Non-realtime messages and the Data Set (DT1) messages in the System Exclusive messages transmitted by this device.

Universal Non-realtime System Exclusive Messages


Effect 1 (Reverb Send Level) (Controller number 91)
status 2nd byte 3rd byte BnH 5BH vvH n=MIDI channel number: 0H - FH (ch.1 - ch.16) vv=Reverb Send Level: 00H - 7FH (0 - 127)

Identity Reply Message


When Identity Request message (p. 186) is received, this message will be transmitted. status F0H data byte 7EH, dev, 06H, 02H, 41H, 6AH, 00H, 04H, 00H, 00H, 01H, 00H, 00H status F7H

Effect 3 (Chorus Send Level) (Controller number 93)


status 2nd byte 3rd byte BnH 5DH vvH n=MIDI channel: 0H - FH (ch.1 - ch.16) vv=Chorus Send Level: 00H - 7FH (0 - 127) Byte F0H 7EH dev 06H 02H 41H 6AH 00H 04H 00H 00H 01H 00H 00H F7H

RPN MSB/LSB (Controller number 100,101)


status 2nd byte 3rd byte BnH 65H mmH BnH 64H llH n=MIDI channel number: 0H - FH (ch.1 - ch.16) mm=MSB of the parameter number specified by RPN ll=LSB of the parameter number specified by RPN This device transmits the following RPNs. RPN MSB LSB 00H 00H Data entry MSB LSB mmH -

Remarks Exclusive status ID number (Universal Non-realtime message) device ID (dev: 10H - 1FH) sub ID#1 (General Information) sub ID#2 (Identity Reply) ID number (Roland) Device family code Device family number code Software revision level EOX (End Of Exclusive)

Data Transmission
Data Set1
Notes Pitch Bend Sensitivity mm : 00H - 0CH (0 - 12 semitones) ll : 00H Channel Fine Tuning mm, ll : 20 00H - 40 00H - 60 00H ( -4096 x 100 / 8192 - 0 - +4096 x 100 / 8192 cent ) Channel Coarse Tuning mm : 10H - 40H - 70H (-48 - 0 - +48 semitones) ll : 00H status F0H

DT1
data byte 41H, dev, 6AH, 12H, aaH, bbH, ccH, ddH, eeH, ... ffH, sum Remarks Exclusive status ID number device ID model ID command ID address MSB address address address LSB data: : data checksum EOX status F7H

00H 01H

mmH llH

00H 02H

mmH -

Program Change
status 2nd byte CnH ppH n=MIDI channel: 0H - FH (ch.1 - ch.16) pp=Program number: 00H - 7FH (prog.1 - prog.128) * This message is not transmitted when the Program parameter (SYSTEM/MIDI/ TRANSMIT MIDI) is OFF.

: ffH sum F7H *

(End Of Exclusive)

Channel Aftertouch
status 2nd byte DnH vvH n=MIDI channel: 0H - FH (ch.1 - ch.16) vv=Channel Aftertouch: 00H - 7FH (1 - 128)

* *

The amount of data transmitted at one time is fixed for the type of data, and the data will be transmitted with the fixed starting address and size. Refer to the address and size given in Parameter Address Map (p. 190). Large amounts of data must be divided into packets of 128 bytes or less, and transmitted at intervals of approximately 20 ms. For the checksum, refer to (p. 204).

189

Appendices

Byte F0H 41H dev 6AH 12H aaH bbH ccH ddH eeH

(Roland) (dev: 10H - 1FH) (XP-30) (DT1)

The actual data to be transmitted. Multi-byte data is transmitted in the address order.

MIDI Implementation

3. Parameter Address Map


1. XP-30 (Model ID=6AH)
* * For addresses marked by a #, the data must be divided into 2 parts for transmission. For example, data with the hexadecimal value ABH would be divided into 0AH and 0BH, and transmitted in that order. Parameter values enclosed in < > are for the JV-1010 / JV-1080 / JV-2080 / XP-50 / XP-60 / XP-80, and will be ignored if received by the XP-30.

++ | Start | | | Address | Description | |+| | 00 00 00 00 | System 1-1 | |+| | 01 00 00 00 | Temporary Performance 1-2 | | 02 00 00 00 | Performance Mode Temporary Patch(part 1) 1-3 | | 02 01 00 00 | Performance Mode Temporary Patch(part 2) | | : | | | 02 08 00 00 | Performance Mode Temporary Patch(part 9) | | 02 09 00 00 | Temporary Rhythm Setup 1-4 | | 02 0A 00 00 | Performance Mode Temporary Patch(part 11) 1-3 | | : | | | 02 0F 00 00 | Performance Mode Temporary Patch(part 16) | | 03 00 00 00 | Patch Mode Temporary Patch 1-3 | |+| | 10 00 00 00 | User Performance USER:01 1-2 | | 10 01 00 00 | User Performance USER:02 | | : | | | 10 1F 00 00 | User Performance USER:32 | | 10 40 00 00 | User Rhythm Setup USER:1 1-4 | | 10 41 00 00 | User Rhythm Setup USER:2 | | 11 00 00 00 | User Patch USER:001 1-3 | | 11 01 00 00 | User Patch USER:002 | | : | | | 11 7F 00 00 | User Patch USER:128 | ++

q 1-1.System
++ | Offset | | | Address | Description | |+| | 00 00 | System Common 1-1-1 | | 10 00 | Part 1 Scale Tune 1-1-2 | | 11 00 | Part 2 Scale Tune | | : | | | 1F 00 | Part 16 Scale Tune | | 20 00 | Patch Mode Scale Tune 1-1-2 | ++

q 1-1-1.System Common
++ | Offset | | | Address | Size | Description Data (Value) | |+| | 00 00 | 0000 00aa | Sound Mode 0 - 2 *1 | | 00 01 | 0aaa aaaa | Performance Number 0 - 127 *2 | | 00 02 | 0000 00aa | Patch Group Type 0 - 2 *3 -> | | 00 03 | 0aaa aaaa | Patch Group ID 0 - 127 -> | |# 00 04 | 0000 aaaa | Patch Number 0 - 255 -> | | | 0000 bbbb | (001 - 256) | | 00 06 | 0aaa aaaa | Master Tune 0 - 126 *4 | | 00 07 | 0000 000a | Scale Tune Switch 0 - 1 (OFF,ON) | | 00 08 | 0000 000a | EFX Switch 0 - 1 (OFF,ON) | | 00 09 | 0000 000a | Chorus Switch 0 - 1 (OFF,ON) | | 00 0A | 0000 000a | Reverb Switch 0 - 1 (OFF,ON) | | 00 0B | 0000 000a | Patch Remain 0 - 1 (OFF,ON) | | 00 0C | 0000 000a | Clock Source 0 - 1 (INT,MIDI) | | 00 0D | 0000 0aaa | TAP Control Source 0 - 4 *5 | | 00 0E | 0000 0aaa | Hold Control Source 0 - 4 *6 | | 00 0F | 0000 0aaa | Peak Control Source 0 - 4 *6 | | 00 10 | 0000 000a | Volume Control Source 0 - 1 *7 | | 00 11 | 0000 00aa | Aftertouch Source 0 - 2 *8 | | 00 12 | 0aaa aaaa | System Control Source 1 1 - 97 *9 | | 00 13 | 0aaa aaaa | System Control Source 2 1 - 97 *9 | |++| | 00 14 | 0000 000a | Receive Program Change 0 - 1 (OFF,ON) | | 00 15 | 0000 000a | Receive Bank Select 0 - 1 (OFF,ON) | | 00 16 | 0000 000a | Receive Control Change 0 - 1 (<OFF,ON>) | | 00 17 | 0000 000a | Receive Modulation 0 - 1 (<OFF,ON>) | | 00 18 | 0000 000a | Receive Volume 0 - 1 (<OFF,ON>) | | 00 19 | 0000 000a | Receive Hold-1 0 - 1 (<OFF,ON>) | | 00 1A | 0000 000a | Receive Pitch Bend 0 - 1 (<OFF,ON>) | | 00 1B | 0000 000a | Receive Aftertouch 0 - 1 (<OFF,ON>) | | 00 1C | 000a aaaa | Control Channel 0 - 16 (1 - 16,OFF)| | 00 1D | 0000 aaaa | Patch Receive Channel 0 - 15 (1 - 16) | | 00 1E | 0000 000a | Rhythm Edit Source 0 - 1 *10 | |++| | 00 1F | 0000 00aa | Preview Sound Mode 0 - 2 *11 | | 00 20 | 0aaa aaaa | Preview Note Set 1 0 - 127 (C-1 - G9) | | 00 21 | 0aaa aaaa | Preview Velocity Set 1 0 - 127 *12 | | 00 22 | 0aaa aaaa | Preview Note Set 2 0 - 127 (C-1 - G9) | | 00 23 | 0aaa aaaa | Preview Velocity Set 2 0 - 127 *12 | | 00 24 | 0aaa aaaa | Preview Note Set 3 0 - 127 (C-1 - G9) | | 00 25 | 0aaa aaaa | Preview Velocity Set 3 0 - 127 *12 | | 00 26 | 0aaa aaaa | Preview Note Set 4 0 - 127 (C-1 - G9) | | 00 27 | 0aaa aaaa | Preview Velocity Set 4 0 - 127 *12 | |++| | 00 28 | 0000 000a | Transmit Program Change 0 - 1 (OFF,ON) | | 00 29 | 0000 000a | Transmit Bank Select 0 - 1 (OFF,ON) | | 00 2A | 000a aaaa | Patch Transmit Channel 0 - 17 *13 | |++| | 00 2B | 0000 000a | Transpose Switch 0 - 1 (OFF,ON) | | 00 2C | 0000 aaaa | Transpose Value 0 - 11 (-5 - +6) | | 00 2D | 0000 0aaa | Octave Shift 0 - 6 (-3 - +3) | | 00 2E | 0aaa aaaa | Keyboard Velocity 0 - 127 *14 | | 00 2F | 0000 00aa | Keyboard Sens 0 - 2 *15 | | 00 30 | 0aaa aaaa | Aftertouch Sens 0 - 100 | | 00 31 | 0aaa aaaa | Pedal(1) Assign 1 - 104 *16 | | 00 32 | 0000 00aa | Pedal(1) Output Mode 0 - 3 *18 |

++ | Patch Group | Group Type | Group ID | Number (value) | |+++| | USER | 0 | 1 | 0 - 127 (001 - 128) | | <CARD | 0 | 2 | 0 - 127 (001 - 128)>| | PR-A | 0 | 3 | 0 - 127 (001 - 128) | | PR-B | 0 | 4 | 0 - 127 (001 - 128) | | PR-C | 0 | 5 | 0 - 127 (001 - 128) | | PR-D | 0 | 6 | 0 - 127 (001 - 128) | | PR-E | 0 | 7 | 0 - 127 (001 - 128) | | <PCM | 1 | 1 - 127 | 0 - 127 (001 - 128)>| |XP-A(Session)| 2 | 9 | 0 - 254 (001 - 255) | | XP-B(Orch.) | 2 | 2 | 0 - 254 (001 - 255) | | XP-C(Techno)| 2 | 11 | 0 - 255 (001 - 256) | | XP-D | 2 | 1 - 127 | 0 - 255 (001 - 256) | | XP-E | 2 | 1 - 127 | 0 - 255 (001 - 256) | +-----------------------------------------------------------+

190

MIDI Implementation

| 00 33 | 0000 000a | Pedal(1) Polarity 0 - 1 *20 | | 00 34 | 0aaa aaaa | Pedal2 Assign 1 - 104 *17 | | 00 35 | 0000 00aa | Pedal2 Output Mode 0 - 3 *19 | | 00 36 | 0000 000a | Pedal2 Polarity 0 - 1 *21 | | 00 37 | 0aaa aaaa | C1 Assign 1 - 97 *9 | | 00 38 | 0000 00aa | C1 Output Mode 0 - 3 *18 | | 00 39 | 0aaa aaaa | C2 Assign 1 - 97 *9 | | 00 3A | 0000 00aa | C2 Output Mode 0 - 3 *18 | | 00 3B | 0000 00aa | Hold Pedal Output Mode 0 - 3 *18 | | 00 3C | 0000 000a | Hold Pedal Polarity 0 - 1 *20 | |++| | 00 3D | 0000 000a | Bank Select Group1 Switch 0 - 1 (OFF,ON) | | 00 3E | 0aaa aaaa | Bank Select Group1 MSB 0 - 127 | | 00 3F | 0aaa aaaa | Bank Select Group1 LSB 0 - 127 | | 00 40 | 0000 000a | Bank Select Group2 Switch 0 - 1 (OFF,ON) | | 00 41 | 0aaa aaaa | Bank Select Group2 MSB 0 - 127 | | 00 42 | 0aaa aaaa | Bank Select Group2 LSB 0 - 127 | | 00 43 | 0000 000a | Bank Select Group3 Switch 0 - 1 (OFF,ON) | | 00 44 | 0aaa aaaa | Bank Select Group3 MSB 0 - 127 | | 00 45 | 0aaa aaaa | Bank Select Group3 LSB 0 - 127 | | 00 46 | 0000 000a | Bank Select Group4 Switch 0 - 1 (OFF,ON) | | 00 47 | 0aaa aaaa | Bank Select Group4 MSB 0 - 127 | | 00 48 | 0aaa aaaa | Bank Select Group4 LSB 0 - 127 | | 00 49 | 0000 000a | Bank Select Group5 Switch 0 - 1 (OFF,ON) | | 00 4A | 0aaa aaaa | Bank Select Group5 MSB 0 - 127 | | 00 4B | 0aaa aaaa | Bank Select Group5 LSB 0 - 127 | | 00 4C | 0000 000a | Bank Select Group6 Switch 0 - 1 (OFF,ON) | | 00 4D | 0aaa aaaa | Bank Select Group6 MSB 0 - 127 | | 00 4E | 0aaa aaaa | Bank Select Group6 LSB 0 - 127 | | 00 4F | 0000 000a | Bank Select Group7 Switch 0 - 1 (OFF,ON) | | 00 50 | 0aaa aaaa | Bank Select Group7 MSB 0 - 127 | | 00 51 | 0aaa aaaa | Bank Select Group7 LSB 0 - 127 | |++| | 00 52 | 0aaa aaaa | Pedal3 Assign 1 - 104 *17 | | 00 53 | 0000 00aa | Pedal3 Output Mode 0 - 3 *19 | | 00 54 | 0000 000a | Pedal3 Polarity 0 - 1 *21 | | 00 55 | 0aaa aaaa | Pedal4 Assign 1 - 104 *17 | | 00 56 | 0000 00aa | Pedal4 Output Mode 0 - 3 *19 | | 00 57 | 0000 000a | Pedal4 Polarity 0 - 1 *21 | |++| | 00 58 | 00aa aaaa | Arpeggio Style 0 - 42 (1 - 43) | | 00 59 | 00aa aaaa | Arpeggio Motif 0 - 37 (1 - 38) | | 00 5A | 0aaa aaaa | Arpeggio Beat Pattern 0 - 114 (1 - 115) | | 00 5B | 0aaa aaaa | Arpeggio Accent Rate 0 - 100 | | 00 5C | 0aaa aaaa | Arpeggio Shuffle Rate 50 - 90 | | 00 5D | 0aaa aaaa | Arpeggio Keyboard Velocity 0 - 127 *14 | | 00 5E | 0000 0aaa | Arpeggio Octave Range 0 - 6 (-3 - +3) | | 00 5F | 0000 aaaa | Arpeggio Part Number 0 - 15 *22 | |++| |# 00 60 | 0000 aaaa | System Tempo 20 - 250 | | | 0000 bbbb | | |++| | 00 62 | 0aaa aaaa | C3 Assign 1 - 97 *9 | | 00 63 | 0000 00aa | C3 Output Mode 0 - 3 *18 | | 00 64 | 0aaa aaaa | C4 Assign 1 - 97 *9 | | 00 65 | 0000 00aa | C4 Output Mode 0 - 3 *18 | |+| |Total size | 00 00 00 66 | ++ *1 *2 *3 *4 *5 *6 *7 *8 *9 *10 *11 *12 *13 *14 *15 *16 *17 *18 *19 *20 *21 *22 PERFORMANCE, PATCH, GM USER:01USER:32, <CARD:01CARD:32>, PR-A:01PR-A:32, PR-B:01PR-B:32 USER&PRESET, <PCM>, EXP 427.4452.6 <OFF, HOLD-1, SOSTENUTO, SOFT, HOLD-2> OFF, HOLD-1, SOSTENUTO, SOFT, HOLD-2 VOLUME, VOLUME&EXPRESSION CHANNEL, POLY, CH&POLY CC01CC05, CC07CC31, CC64CC95, PITCH BEND, AFTERTOUCH <PANEL, PANEL&MIDI> SINGLE, CHORD, PHRASE OFF, 1127 116, RX-CH, OFF REAL, 1127 LIGHT, MEDIUM, HEAVY CC01CC05, CC07CC31, CC64CC95, PITCH BEND, AFTERTOUCH, PROG-UP, PROG-DOWN, <START/STOP>, <PUNCH-IN/OUT>, TAP-TEMPO, OCTAVE-UP, OCTAVE-DOWN <CC01CC05, CC07CC31, CC64CC95, PITCH BEND, AFTERTOUCH, PROG-UP, PROG-DOWN, <START/STOP>, <PUNCH-IN/OUT>, TAP-TEMPO, OCTAVE-UP, OCTAVE-DOWN> OFF, INT, MIDI, INT&MIDI <OFF, INT, MIDI, INT&MIDI> STANDARD, REVERSE <STANDARD, REVERSE> PART1PART16

++ | Offset | | | Address | Size | Description Data (Value) | |+| | 00 00 | 0aaa aaaa | Scale Tune for C 0 - 127 (-64 - +63)| | 00 01 | 0aaa aaaa | Scale Tune for C# 0 - 127 (-64 - +63)| | 00 02 | 0aaa aaaa | Scale Tune for D 0 - 127 (-64 - +63)| | 00 03 | 0aaa aaaa | Scale Tune for D# 0 - 127 (-64 - +63)| | 00 04 | 0aaa aaaa | Scale Tune for E 0 - 127 (-64 - +63)| | 00 05 | 0aaa aaaa | Scale Tune for F 0 - 127 (-64 - +63)| | 00 06 | 0aaa aaaa | Scale Tune for F# 0 - 127 (-64 - +63)| | 00 07 | 0aaa aaaa | Scale Tune for G 0 - 127 (-64 - +63)| | 00 08 | 0aaa aaaa | Scale Tune for G# 0 - 127 (-64 - +63)| | 00 09 | 0aaa aaaa | Scale Tune for A 0 - 127 (-64 - +63)| | 00 0A | 0aaa aaaa | Scale Tune for A# 0 - 127 (-64 - +63)| | 00 0B | 0aaa aaaa | Scale Tune for B 0 - 127 (-64 - +63)| |+| |Total size | 00 00 00 0C | ++

191

Appendices

q 1-1-2.Scale Tune

MIDI Implementation

q 1-2.Performance
++ | Offset | | | Address | Description | |+| | 00 00 | Performance Common 1-2-1 | | 10 00 | Performance Part 1 1-2-2 | | 11 00 | Performance Part 2 | | : | | | 1F 00 | Performance Part 16 | ++

q 1-2-1.Performance Common
++ | Offset | | | Address | Size | Description Data (Value) | |+| | 00 00 | 0aaa aaaa | Performance Name 1 32 - 127 | | 00 01 | 0aaa aaaa | Performance Name 2 32 - 127 | | 00 02 | 0aaa aaaa | Performance Name 3 32 - 127 | | 00 03 | 0aaa aaaa | Performance Name 4 32 - 127 | | 00 04 | 0aaa aaaa | Performance Name 5 32 - 127 | | 00 05 | 0aaa aaaa | Performance Name 6 32 - 127 | | 00 06 | 0aaa aaaa | Performance Name 7 32 - 127 | | 00 07 | 0aaa aaaa | Performance Name 8 32 - 127 | | 00 08 | 0aaa aaaa | Performance Name 9 32 - 127 | | 00 09 | 0aaa aaaa | Performance Name 10 32 - 127 | | 00 0A | 0aaa aaaa | Performance Name 11 32 - 127 | | 00 0B | 0aaa aaaa | Performance Name 12 32 - 127 | |++| | 00 0C | 0000 aaaa | EFX Source 0 - 15 *1 | | 00 0D | 00aa aaaa | EFX Type 0 - 39 (1 - 40) | | 00 0E | 0aaa aaaa | EFX Parameter 1 0 - 127 | | 00 0F | 0aaa aaaa | EFX Parameter 2 0 - 127 | | 00 10 | 0aaa aaaa | EFX Parameter 3 0 - 127 | | 00 11 | 0aaa aaaa | EFX Parameter 4 0 - 127 | | 00 12 | 0aaa aaaa | EFX Parameter 5 0 - 127 | | 00 13 | 0aaa aaaa | EFX Parameter 6 0 - 127 | | 00 14 | 0aaa aaaa | EFX Parameter 7 0 - 127 | | 00 15 | 0aaa aaaa | EFX Parameter 8 0 - 127 | | 00 16 | 0aaa aaaa | EFX Parameter 9 0 - 127 | | 00 17 | 0aaa aaaa | EFX Parameter 10 0 - 127 | | 00 18 | 0aaa aaaa | EFX Parameter 11 0 - 127 | | 00 19 | 0aaa aaaa | EFX Parameter 12 0 - 127 | | 00 1A | 0000 00aa | EFX Output Assign 0 - 2 *2 | | 00 1B | 0aaa aaaa | EFX Mix Out Send Level 0 - 127 | | 00 1C | 0aaa aaaa | EFX Chorus Send Level 0 - 127 | | 00 1D | 0aaa aaaa | EFX Reverb Send Level 0 - 127 | | 00 1E | 0000 aaaa | EFX Control Source 1 0 - 10 *3 | | 00 1F | 0aaa aaaa | EFX Control Depth 1 0 - 126 (-63 - +63)| | 00 20 | 0000 aaaa | EFX Control Source 2 0 - 10 *3 | | 00 21 | 0aaa aaaa | EFX Control Depth 2 0 - 126 (-63 - +63)| | 00 22 | 0aaa aaaa | Chorus Level 0 - 127 | | 00 23 | 0aaa aaaa | Chorus Rate 0 - 127 | | 00 24 | 0aaa aaaa | Chorus Depth 0 - 127 | | 00 25 | 0aaa aaaa | Chorus Pre-Delay 0 - 127 | | 00 26 | 0aaa aaaa | Chorus Feedback 0 - 127 | | 00 27 | 0000 00aa | Chorus Output 0 - 2 *4 | | 00 28 | 0000 0aaa | Reverb Type 0 - 7 *5 | | 00 29 | 0aaa aaaa | Reverb Level 0 - 127 | | 00 2A | 0aaa aaaa | Reverb Time 0 - 127 | | 00 2B | 000a aaaa | Reverb HF Damp 0 - 17 *6 | | 00 2C | 0aaa aaaa | Delay Feedback 0 - 127 | |++| |# 00 2D | 0000 aaaa | Performance Tempo 20 - 250 | | | 0000 bbbb | | | 00 2F | 0000 000a | Keyboard Range Switch 0 - 1 (OFF,ON) | |++| | 00 30 | 0aaa aaaa | Voice Reserve 1 0 - 64 | | 00 31 | 0aaa aaaa | Voice Reserve 2 0 - 64 | | 00 32 | 0aaa aaaa | Voice Reserve 3 0 - 64 | | 00 33 | 0aaa aaaa | Voice Reserve 4 0 - 64 | | 00 34 | 0aaa aaaa | Voice Reserve 5 0 - 64 | | 00 35 | 0aaa aaaa | Voice Reserve 6 0 - 64 | | 00 36 | 0aaa aaaa | Voice Reserve 7 0 - 64 | | 00 37 | 0aaa aaaa | Voice Reserve 8 0 - 64 | | 00 38 | 0aaa aaaa | Voice Reserve 9 0 - 64 | | 00 39 | 0aaa aaaa | Voice Reserve 10 0 - 64 | | 00 3A | 0aaa aaaa | Voice Reserve 11 0 - 64 | | 00 3B | 0aaa aaaa | Voice Reserve 12 0 - 64 | | 00 3C | 0aaa aaaa | Voice Reserve 13 0 - 64 | | 00 3D | 0aaa aaaa | Voice Reserve 14 0 - 64 | | 00 3E | 0aaa aaaa | Voice Reserve 15 0 - 64 | | 00 3F | 0aaa aaaa | Voice Reserve 16 0 - 64 | |++| | 00 40 | 0000 000a | Keyboard Mode 0 - 1 *7 | | 00 41 | 0000 000a | Clock Source 0 - 1 *8 | |+| |Total size | 00 00 00 42 | ++ *1 *2 *3 *4 *5 *6 *7 *8 PERFORM, 19, 1116 MIX, <DIRECT-1>, <DIRECT-2> OFF, SYS-CTRL1, SYS-CTRL2, MODULATION, BREATH, FOOT, VOLUME, PAN, EXPRESSION, PITCH BEND, AFTERTOUCH MIX, REV, MIX+REV ROOM1, ROOM2, STAGE1, STAGE2, HALL1, HALL2, DELAY, PAN-DLY 200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1600, 2000, 2500, 3150, 4000, 5000, 6300, 8000, BYPASS LAYER, SINGLE PERFORMANCE, SYSTEM

192

MIDI Implementation

q 1-2-2.Performance Part
++ | Offset | | | Address | Size | Description Data (Value) | |+| | 00 00 | 0000 000a | Receive Switch 0 - 1 (OFF,ON) | | 00 01 | 0000 aaaa | MIDI Channel 0 - 15 (1 - 16) | |++| | 00 02 | 0000 00aa | Patch Group Type 0 - 2 *1 -> | | 00 03 | 0aaa aaaa | Patch Group ID 0 - 127 -> | |# 00 04 | 0000 aaaa | Patch Number 0 - 255 -> | | | 0000 bbbb | (001 - 256)| | 00 06 | 0aaa aaaa | Part Level 0 - 127 | | 00 07 | 0aaa aaaa | Part Pan 0 - 127 (L64 - 63R)| | 00 08 | 0aaa aaaa | Part Coarse Tune 0 - 96 (-48 - +48)| | 00 09 | 0aaa aaaa | Part Fine Tune 0 - 100 (-50 - +50)| | 00 0A | 0000 0aaa | Output Assign 0 - 4 *2 | | 00 0B | 0aaa aaaa | Mix/EFX Send Level 0 - 127 | | 00 0C | 0aaa aaaa | Chorus Send Level 0 - 127 | | 00 0D | 0aaa aaaa | Reverb Send Level 0 - 127 | | 00 0E | 0000 000a | Receive Program Change Switch 0 - 1 (OFF,ON) | | 00 0F | 0000 000a | Receive Volume Switch 0 - 1 (OFF,ON) | | 00 10 | 0000 000a | Receive Hold-1 Switch 0 - 1 (OFF,ON) | | 00 11 | 0aaa aaaa | Keyboard Range Lower 0 - 127 *3 | | 00 12 | 0aaa aaaa | Keyboard Range Upper 0 - 127 *4 | |++| | 00 13 | 0000 0aaa | Octave Shift 0 - 6 (-3 - +3) | | 00 14 | 0000 000a | Local Switch 0 - 1 (OFF,ON) | | 00 15 | 0000 000a | Transmit Switch 0 - 1 (OFF,ON) | | 00 16 | 0000 0aaa | Transmit Bank Select Group 0 - 7 *5 | |# 00 17 | 0000 aaaa | Transmit Volume 0 - 128 | | | 0000 bbbb | (0 - 127,OFF) | |+| |Total size | 00 00 00 19 | ++ *1 *2 *3 *4 *5 USER&PRESET, <PCM>, EXP MIX, EFX, <DIRECT-1>, <DIRECT-2>, PATCH C-1Upper LowerG9 PATCH, GROUP1GROUP7

++ | Patch Group | Group Type | Group ID | Number (value) | |+++| | USER | 0 | 1 | 0 - 127 (001 - 128) | | <CARD | 0 | 2 | 0 - 127 (001 - 128)>| | PR-A | 0 | 3 | 0 - 127 (001 - 128) | | PR-B | 0 | 4 | 0 - 127 (001 - 128) | | PR-C | 0 | 5 | 0 - 127 (001 - 128) | | PR-D | 0 | 6 | 0 - 127 (001 - 128) | | PR-E | 0 | 7 | 0 - 127 (001 - 128) | | <PCM | 1 | 1 - 127 | 0 - 127 (001 - 128)>| |XP-A(Session)| 2 | 9 | 0 - 254 (001 - 255) | | XP-B(Orch.) | 2 | 2 | 0 - 254 (001 - 255) | | XP-C(Techno)| 2 | 11 | 0 - 255 (001 - 256) | | XP-D | 2 | 1 - 127 | 0 - 255 (001 - 256) | | XP-E | 2 | 1 - 127 | 0 - 255 (001 - 256) | ++

q 1-3.Patch
++ | Offset | | | Address | Description | |+| | 00 00 | Patch Common 1-3-1 | | 10 00 | Patch Tone 1 1-3-2 | | 12 00 | Patch Tone 2 | | 14 00 | Patch Tone 3 | | 16 00 | Patch Tone 4 | ++

q 1-3-1.Patch Common
++ | Offset | | | Address | Size | Description Data (Value) | |+| | 00 00 | 0aaa aaaa | Patch Name 1 32 - 127 | | 00 01 | 0aaa aaaa | Patch Name 2 32 - 127 | | 00 02 | 0aaa aaaa | Patch Name 3 32 - 127 | | 00 03 | 0aaa aaaa | Patch Name 4 32 - 127 | | 00 04 | 0aaa aaaa | Patch Name 5 32 - 127 | | 00 05 | 0aaa aaaa | Patch Name 6 32 - 127 | | 00 06 | 0aaa aaaa | Patch Name 7 32 - 127 | | 00 07 | 0aaa aaaa | Patch Name 8 32 - 127 | | 00 08 | 0aaa aaaa | Patch Name 9 32 - 127 | | 00 09 | 0aaa aaaa | Patch Name 10 32 - 127 | | 00 0A | 0aaa aaaa | Patch Name 11 32 - 127 | | 00 0B | 0aaa aaaa | Patch Name 12 32 - 127 | |++| | 00 0C | 00aa aaaa | EFX Type 0 - 39 (1 - 40) | | 00 0D | 0aaa aaaa | EFX Parameter 1 0 - 127 | | 00 0E | 0aaa aaaa | EFX Parameter 2 0 - 127 | | 00 0F | 0aaa aaaa | EFX Parameter 3 0 - 127 | | 00 10 | 0aaa aaaa | EFX Parameter 4 0 - 127 | | 00 11 | 0aaa aaaa | EFX Parameter 5 0 - 127 | | 00 12 | 0aaa aaaa | EFX Parameter 6 0 - 127 | | 00 13 | 0aaa aaaa | EFX Parameter 7 0 - 127 | | 00 14 | 0aaa aaaa | EFX Parameter 8 0 - 127 | | 00 15 | 0aaa aaaa | EFX Parameter 9 0 - 127 | | 00 16 | 0aaa aaaa | EFX Parameter 10 0 - 127 | | 00 17 | 0aaa aaaa | EFX Parameter 11 0 - 127 | | 00 18 | 0aaa aaaa | EFX Parameter 12 0 - 127 | | 00 19 | 0000 00aa | EFX Output Assign 0 - 2 *1 | | 00 1A | 0aaa aaaa | EFX Mix Out Send Level 0 - 127 | | 00 1B | 0aaa aaaa | EFX Chorus Send Level 0 - 127 | | 00 1C | 0aaa aaaa | EFX Reverb Send Level 0 - 127 | | 00 1D | 0000 aaaa | EFX Control Source 1 0 - 10 *2 | | 00 1E | 0aaa aaaa | EFX Control Depth 1 0 - 126 (-63 - +63)| | 00 1F | 0000 aaaa | EFX Control Source 2 0 - 10 | | 00 20 | 0aaa aaaa | EFX Control Depth 2 0 - 126 (-63 - +63)| | 00 21 | 0aaa aaaa | Chorus Level 0 - 127 | | 00 22 | 0aaa aaaa | Chorus Rate 0 - 127 | | 00 23 | 0aaa aaaa | Chorus Depth 0 - 127 | | 00 24 | 0aaa aaaa | Chorus Pre-Delay 0 - 127 | | 00 25 | 0aaa aaaa | Chorus Feedback 0 - 127 | | 00 26 | 0000 00aa | Chorus Output 0 - 2 *3 | | 00 27 | 0000 0aaa | Reverb Type 0 - 7 *4 | | 00 28 | 0aaa aaaa | Reverb Level 0 - 127 | | 00 29 | 0aaa aaaa | Reverb Time 0 - 127 | | 00 2A | 000a aaaa | Reverb HF Damp 0 - 17 *5 | | 00 2B | 0aaa aaaa | Delay Feedback 0 - 127 |

193

Appendices

MIDI Implementation

|++| |# 00 2C | 0000 aaaa | Patch Tempo 20 - 250 | | | 0000 bbbb | | | 00 2E | 0aaa aaaa | Patch Level 0 - 127 | | 00 2F | 0aaa aaaa | Patch Pan 0 - 127 (L64 - 63R)| | 00 30 | 0aaa aaaa | Analog Feel 0 - 127 | | 00 31 | 0000 aaaa | Bend Range Up 0 - 12 | | 00 32 | 00aa aaaa | Bend Range Down 0 - 48 (0 - -48) | | 00 33 | 0000 000a | Key Assign Mode 0 - 1 (POLY,SOLO)| | 00 34 | 0000 000a | Solo Legato 0 - 1 (OFF,ON) | | 00 35 | 0000 000a | Portamento Switch 0 - 1 (OFF,ON) | | 00 36 | 0000 000a | Portamento Mode 0 - 1 *6 | | 00 37 | 0000 000a | Portamento Type 0 - 1 (RATE,TIME)| | 00 38 | 0000 000a | Portamento Start 0 - 1 *7 | | 00 39 | 0aaa aaaa | Portamento Time 0 - 127 | | 00 3A | 0000 aaaa | Patch Control Source 2 0 - 15 *8 | | 00 3B | 0000 aaaa | Patch Control Source 3 0 - 15 *8 | | 00 3C | 0000 00aa | EFX Control Hold/Peak 0 - 2 *9 | | 00 3D | 0000 00aa | Control 1 Hold/Peak 0 - 2 *9 | | 00 3E | 0000 00aa | Control 2 Hold/Peak 0 - 2 *9 | | 00 3F | 0000 00aa | Control 3 Hold/Peak 0 - 2 *9 | | 00 40 | 0000 000a | Velocity Range Switch 0 - 1 (OFF,ON) | | 00 41 | 0000 0aaa | Octave Shift 0 - 6 (-3 - +3) | | 00 42 | 0000 00aa | Stretch Tune Depth 0 - 3 (OFF,1 - 3)| | 00 43 | 0000 000a | Voice Priority 0 - 1 *10 | |++| | 00 44 | 0000 aaaa | Structure Type 1&2 0 - 9 (1 - 10) | | 00 45 | 0000 00aa | Booster 1&2 0 - 3 *11 | | 00 46 | 0000 aaaa | Structure Type 3&4 0 - 9 (1 - 10) | | 00 47 | 0000 00aa | Booster 3&4 0 - 3 *11 | |++| | 00 48 | 0000 000a | Clock Source 0 - 1 *12 | | 00 49 | 0aaa aaaa | Patch Category 0 - 127 *13 | |+| |Total size | 00 00 00 4A | ++ *1 *2 *3 *4 *5 *6 *7 *8 *9 *10 *11 *12 *13 MIX, <DIRECT-1>, <DIRECT-2> OFF, SYS-CTRL1, SYS-CTRL2, MODULATION, BREATH, FOOT, VOLUME, PAN, EXPRESSION, PITCH BEND, AFTERTOUCH MIX, REV, MIX+REV ROOM1, ROOM2, STAGE1, STAGE2, HALL1, HALL2, DELAY, PAN-DLY 200, 250, 315, 400, 500, 630, 800, 1000, 1250, 1600, 2000, 2500, 3150, 4000, 5000, 6300, 8000, BYPASS NORMAL, LEGATO PITCH, NOTE OFF, SYS-CTRL1, SYS-CTRL2, MODULATION, BREATH, FOOT, VOLUME, PAN, EXPRESSION, PITCH BEND, AFTERTOUCH, LFO1, LFO2, VELOCITY, KEYFOLLOW, PLAYMATE OFF, HOLD, PEAK LAST, LOUDEST 0, +6, +12, +18 PATCH, SYSTEM NO ASSIGN, AC.PIANO, EL.PIANO, KEYBOARDS, BELL, MALLET, ORGAN, ACCORDION, HARMONICA, AC.GUITAR, EL.GUITAR, DIST.GUITAR, BASS, SYNTH BASS, STRINGS, ORCHESTRA, HIT&STAB, WIND, FLUTE, AC.BRASS, SYNTH BRASS, SAX, HARD LEAD, SOFT LEAD, TECHNO SYNTH, PULSATING, SYNTH FX, OTHER SYNTH, BRIGHT PAD, SOFT PAD, VOX, PLUCKED, ETHNIC, FRETTED, PERCUSSION, SOUND FX, BEAT&GROOVE, DRUMS, COMBINATION (038)

q 1-3-2.Patch Tone
++ | Offset | | | Address | Size | Description Data (Value) | |+| | 00 00 | 0000 000a | Tone Switch 0 - 1 (OFF,ON) | | 00 01 | 0000 00aa | Wave Group Type 0 - 2 *1 -> | | 00 02 | 0aaa aaaa | Wave Group ID 0 - 127 -> | |# 00 03 | 0000 aaaa | Wave Number 0 - 254 -> | | | 0000 bbbb | (001 - 255)| | 00 05 | 0000 00aa | Wave Gain 0 - 3 *2 | | 00 06 | 0000 000a | FXM Switch 0 - 1 (OFF,ON) | | 00 07 | 0000 00aa | FXM Color 0 - 3 (1 - 4) | | 00 08 | 0000 aaaa | FXM Depth 0 - 15 (1 - 16) | | 00 09 | 0000 0aaa | Tone Delay Mode 0 - 7 *3 | | 00 0A | 0aaa aaaa | Tone Delay Time 0 - 127 | |++| | 00 0B | 0aaa aaaa | Velocity Cross Fade 0 - 127 | | 00 0C | 0aaa aaaa | Velocity Range Lower 1 - 127 *4 | | 00 0D | 0aaa aaaa | Velocity Range Upper 1 - 127 *5 | | 00 0E | 0aaa aaaa | Keyboard Range Lower 0 - 127 *6 | | 00 0F | 0aaa aaaa | Keyboard Range Upper 0 - 127 *7 | | 00 10 | 0000 000a | Redamper Control Switch 0 - 1 (OFF,ON) | | 00 11 | 0000 000a | Volume Control Switch 0 - 1 (OFF,ON) | | 00 12 | 0000 000a | Hold-1 Control Switch 0 - 1 (OFF,ON) | | 00 13 | 0000 000a | Pitch Bend Control Switch 0 - 1 (OFF,ON) | | 00 14 | 0000 00aa | Pan Control Switch 0 - 2 *8 | | 00 15 | 000a aaaa | Controller 1 Destination 1 0 - 18 *9 | | 00 16 | 0aaa aaaa | Controller 1 Depth 1 0 - 126 (-63 - +63)| | 00 17 | 000a aaaa | Controller 1 Destination 2 0 - 18 *9 | | 00 18 | 0aaa aaaa | Controller 1 Depth 2 0 - 126 (-63 - +63)| | 00 19 | 000a aaaa | Controller 1 Destination 3 0 - 18 *9 | | 00 1A | 0aaa aaaa | Controller 1 Depth 3 0 - 126 (-63 - +63)| | 00 1B | 000a aaaa | Controller 1 Destination 4 0 - 18 *9 | | 00 1C | 0aaa aaaa | Controller 1 Depth 4 0 - 126 (-63 - +63)| | 00 1D | 000a aaaa | Controller 2 Destination 1 0 - 18 *9 | | 00 1E | 0aaa aaaa | Controller 2 Depth 1 0 - 126 (-63 - +63)| | 00 1F | 000a aaaa | Controller 2 Destination 2 0 - 18 *9 | | 00 20 | 0aaa aaaa | Controller 2 Depth 2 0 - 126 (-63 - +63)| | 00 21 | 000a aaaa | Controller 2 Destination 3 0 - 18 *9 | | 00 22 | 0aaa aaaa | Controller 2 Depth 3 0 - 126 (-63 - +63)| | 00 23 | 000a aaaa | Controller 2 Destination 4 0 - 18 *9 | | 00 24 | 0aaa aaaa | Controller 2 Depth 4 0 - 126 (-63 - +63)| | 00 25 | 000a aaaa | Controller 3 Destination 1 0 - 18 *9 | | 00 26 | 0aaa aaaa | Controller 3 Depth 1 0 - 126 (-63 - +63)| | 00 27 | 000a aaaa | Controller 3 Destination 2 0 - 18 *9 | | 00 28 | 0aaa aaaa | Controller 3 Depth 2 0 - 126 (-63 - +63)| | 00 29 | 000a aaaa | Controller 3 Destination 3 0 - 18 *9 | | 00 2A | 0aaa aaaa | Controller 3 Depth 3 0 - 126 (-63 - +63)| | 00 2B | 000a aaaa | Controller 3 Destination 4 0 - 18 *9 | | 00 2C | 0aaa aaaa | Controller 3 Depth 4 0 - 126 (-63 - +63)|

++ | Wave Group | Group Type | Group ID | Number (value) | |+++| | INT-A | 0 | 1 | 0 - 254 (001 - 255) | | INT-B | 0 | 2 | 0 - 192 (001 - 193) | | <PCM | 1 | 1 - 127 | 0 - 254 (001 - 255)>| |XP-A(Session)| 2 | 9 | 0 - 205 (001 - 206) | | XP-B(Orch.) | 2 | 2 | 0 - 173 (001 - 174) | | XP-C(Techno)| 2 | 11 | 0 - 254 (001 - 255) | | XP-D | 2 | 1 - 127 | 0 - 254 (001 - 255) | | XP-E | 2 | 1 - 127 | 0 - 254 (001 - 255) | ++

194

MIDI Implementation

|++| | 00 2D | 0000 0aaa | LFO1 Waveform 0 - 7 *10 | | 00 2E | 0000 000a | LFO1 Key Sync 0 - 1 (OFF,ON) | | 00 2F | 0aaa aaaa | LFO1 Rate 0 - 127 | | 00 30 | 0000 0aaa | LFO1 Offset 0 - 4 *11 | | 00 31 | 0aaa aaaa | LFO1 Delay Time 0 - 127 | | 00 32 | 0000 00aa | LFO1 Fade Mode 0 - 3 *12 | | 00 33 | 0aaa aaaa | LFO1 Fade Time 0 - 127 | | 00 34 | 0000 00aa | LFO1 External Sync 0 - 2 *13 | | 00 35 | 0000 0aaa | LFO2 Waveform 0 - 7 *10 | | 00 36 | 0000 000a | LFO2 Key Sync 0 - 1 (OFF,ON) | | 00 37 | 0aaa aaaa | LFO2 Rate 0 - 127 | | 00 38 | 0000 0aaa | LFO2 Offset 0 - 4 *11 | | 00 39 | 0aaa aaaa | LFO2 Delay Time 0 - 127 | | 00 3A | 0000 00aa | LFO2 Fade Mode 0 - 3 *12 | | 00 3B | 0aaa aaaa | LFO2 Fade Time 0 - 127 | | 00 3C | 0000 00aa | LFO2 External Sync 0 - 2 *13 | |++| | 00 3D | 0aaa aaaa | Coarse Tune 0 - 96 (-48 - +48)| | 00 3E | 0aaa aaaa | Fine Tune 0 - 100 (-50 - +50)| | 00 3F | 000a aaaa | Random Pitch Depth 0 - 30 *14 | | 00 40 | 0000 aaaa | Pitch Keyfollow 0 - 15 *15 | | 00 41 | 000a aaaa | Pitch Envelope Depth 0 - 24 (-12 - +12)| | 00 42 | 0aaa aaaa | Pitch Envelope Velocity Sens 0 - 125 *16 | | 00 43 | 0000 aaaa | Pitch Envelope Velocity Time1 0 - 14 *17 | | 00 44 | 0000 aaaa | Pitch Envelope Velocity Time4 0 - 14 *17 | | 00 45 | 0000 aaaa | Pitch Envelope Time Keyfollow 0 - 14 *17 | | 00 46 | 0aaa aaaa | Pitch Envelope Time 1 0 - 127 | | 00 47 | 0aaa aaaa | Pitch Envelope Time 2 0 - 127 | | 00 48 | 0aaa aaaa | Pitch Envelope Time 3 0 - 127 | | 00 49 | 0aaa aaaa | Pitch Envelope Time 4 0 - 127 | | 00 4A | 0aaa aaaa | Pitch Envelope Level 1 0 - 126 (-63 - +63)| | 00 4B | 0aaa aaaa | Pitch Envelope Level 2 0 - 126 (-63 - +63)| | 00 4C | 0aaa aaaa | Pitch Envelope Level 3 0 - 126 (-63 - +63)| | 00 4D | 0aaa aaaa | Pitch Envelope Level 4 0 - 126 (-63 - +63)| | 00 4E | 0aaa aaaa | Pitch LFO1 Depth 0 - 126 (-63 - +63)| | 00 4F | 0aaa aaaa | Pitch LFO2 Depth 0 - 126 (-63 - +63)| |++| | 00 50 | 0000 0aaa | Filter Type 0 - 4 *18 | | 00 51 | 0aaa aaaa | Cutoff Frequency 0 - 127 | | 00 52 | 0000 aaaa | Cutoff Keyfollow 0 - 15 *15 | | 00 53 | 0aaa aaaa | Resonance 0 - 127 | | 00 54 | 0aaa aaaa | Resonance Velocity Sens 0 - 125 *16 | | 00 55 | 0aaa aaaa | Filter Envelope Depth 0 - 126 (-63 - +63)| | 00 56 | 0000 0aaa | Filter Envelope Velocity Curve 0 - 6 (1 - 7) | | 00 57 | 0aaa aaaa | Filter Envelope Velocity Sens 0 - 125 *16 | | 00 58 | 0000 aaaa | Filter Envelope Velocity Time1 0 - 14 *17 | | 00 59 | 0000 aaaa | Filter Envelope Velocity Time4 0 - 14 *17 | | 00 5A | 0000 aaaa | Filter Envelope Time Keyfollow 0 - 14 *17 | | 00 5B | 0aaa aaaa | Filter Envelope Time 1 0 - 127 | | 00 5C | 0aaa aaaa | Filter Envelope Time 2 0 - 127 | | 00 5D | 0aaa aaaa | Filter Envelope Time 3 0 - 127 | | 00 5E | 0aaa aaaa | Filter Envelope Time 4 0 - 127 | | 00 5F | 0aaa aaaa | Filter Envelope Level 1 0 - 127 | | 00 60 | 0aaa aaaa | Filter Envelope Level 2 0 - 127 | | 00 61 | 0aaa aaaa | Filter Envelope Level 3 0 - 127 | | 00 62 | 0aaa aaaa | Filter Envelope Level 4 0 - 127 | | 00 63 | 0aaa aaaa | Filter LFO1 Depth 0 - 126 (-63 - +63)| | 00 64 | 0aaa aaaa | Filter LFO2 Depth 0 - 126 (-63 - +63)| |++| | 00 65 | 0aaa aaaa | Tone Level 0 - 127 | | 00 66 | 0000 00aa | Bias Direction 0 - 3 *19 | | 00 67 | 0aaa aaaa | Bias Position 0 - 127 (C-1 - G9) | | 00 68 | 0000 aaaa | Bias Level 0 - 14 *17 | | 00 69 | 0000 0aaa | Level Envelope Velocity Curve 0 - 6 (1 - 7) | | 00 6A | 0aaa aaaa | Level Envelope Velocity Sens 0 - 125 *16 | | 00 6B | 0000 aaaa | Level Envelope Velocity Time1 0 - 14 *17 | | 00 6C | 0000 aaaa | Level Envelope Velocity Time4 0 - 14 *17 | | 00 6D | 0000 aaaa | Level Envelope Time Keyfollow 0 - 14 *17 | | 00 6E | 0aaa aaaa | Level Envelope Time 1 0 - 127 | | 00 6F | 0aaa aaaa | Level Envelope Time 2 0 - 127 | | 00 70 | 0aaa aaaa | Level Envelope Time 3 0 - 127 | | 00 71 | 0aaa aaaa | Level Envelope Time 4 0 - 127 | | 00 72 | 0aaa aaaa | Level Envelope Level 1 0 - 127 | | 00 73 | 0aaa aaaa | Level Envelope Level 2 0 - 127 | | 00 74 | 0aaa aaaa | Level Envelope Level 3 0 - 127 | | 00 75 | 0aaa aaaa | Level LFO1 Depth 0 - 126 (-63 - +63)| | 00 76 | 0aaa aaaa | Level LFO2 Depth 0 - 126 (-63 - +63)| | 00 77 | 0aaa aaaa | Tone Pan 0 - 127 (L64 - 63R)| | 00 78 | 0000 aaaa | Pan Keyfollow 0 - 14 *17 | | 00 79 | 00aa aaaa | Random Pan Depth 0 - 63 | | 00 7A | 0aaa aaaa | Alternate Pan Depth 1 - 127 (L63 - 63R)| | 00 7B | 0aaa aaaa | Pan LFO1 Depth 0 - 126 (L63 - 63R)| | 00 7C | 0aaa aaaa | Pan LFO2 Depth 0 - 126 (L63 - 63R)| |++| | 00 7D | 0000 00aa | Output Assign 0 - 3 *20 | | 00 7E | 0aaa aaaa | Mix/EFX Send Level 0 - 127 | | 00 7F | 0aaa aaaa | Chorus Send Level 0 - 127 | | 01 00 | 0aaa aaaa | Reverb Send Level 0 - 127 | |+| |Total size | 00 00 01 01 | ++ *1 *2 *3 *4 *5 *6 *7 *8 *9 *10 *11 *12 *13 *14 *15 INT, <PCM>, EXP -6, 0, +6, +12 NORMAL, HOLD, PLAYMATE, CLOCK-SYNC, <TAP-SYNC>, KEY-OFF-N, KEY-OFF-D, TEMPO-SYNC 1Upper Lower127 C-1Upper LowerG9 OFF, CONTINUOUS, KEY-ON OFF, PCH, CUT, RES, LEV, PAN, MIX, CHO, REV, PL1, PL2, FL1, FL2, AL1, AL2, pL1, pL2, L1R, L2R TRI, SIN, SAW, SQR, TRP, S&H, RND, CHS -100, -50, 0, +50, +100 KEY-ON-IN, KEY-ON-OUT, KEY-OFF-IN, KEY-OFF-OUT OFF, CLOCK, <TAP> 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 20, 30, 40, 50, 60, 70, 80, 90, 100, 200, 300, 400, 500, 600, 700, 800, 900, 1000, 1100, 1200 -100, -70, -50, -30, -10, 0, +10, +20, +30, +40, +50, +70, +100, +120, +150, +200

195

Appendices

MIDI Implementation

*16 *17 *18 *19 *20

-100+150 -100, -70, -50, -40, -30, -20, -10, 0, +10, +20, +30, +40, +50, +70, +100 OFF, LPF, BPF, HPF, PKG LOWER, UPPER, LOWER&UPPER, ALL MIX, EFX, <DIRECT-1>, <DIRECT-2>

q 1-4.Rhythm Setup
++ | Offset | | | Address | Description | |+| | 00 00 | Rhythm Common 1-4-1 | | 23 00 | Rhythm Note for Key# 35 1-4-2 | | 24 00 | Rhythm Note for Key# 36 | | : | | | 62 00 | Rhythm Note for Key# 98 | ++

q 1-4-1.Rhythm Common
++ | Offset | | | Address | Size | Description Data (Value) | |+| | 00 00 | 0aaa aaaa | Rhythm Name 1 32 - 127 | | 00 01 | 0aaa aaaa | Rhythm Name 2 32 - 127 | | 00 02 | 0aaa aaaa | Rhythm Name 3 32 - 127 | | 00 03 | 0aaa aaaa | Rhythm Name 4 32 - 127 | | 00 04 | 0aaa aaaa | Rhythm Name 5 32 - 127 | | 00 05 | 0aaa aaaa | Rhythm Name 6 32 - 127 | | 00 06 | 0aaa aaaa | Rhythm Name 7 32 - 127 | | 00 07 | 0aaa aaaa | Rhythm Name 8 32 - 127 | | 00 08 | 0aaa aaaa | Rhythm Name 9 32 - 127 | | 00 09 | 0aaa aaaa | Rhythm Name 10 32 - 127 | | 00 0A | 0aaa aaaa | Rhythm Name 11 32 - 127 | | 00 0B | 0aaa aaaa | Rhythm Name 12 32 - 127 | |+| |Total size | 00 00 00 0C | ++

q 1-4-2.Rhythm Note
++ | Offset | | | Address | Size | Description Data (Value) | |+| | 00 00 | 0000 000a | Tone Switch 0 - 1 (OFF,ON) | | 00 01 | 0000 00aa | Wave Group Type 0 - 2 *1 -> | | 00 02 | 0aaa aaaa | Wave Group ID 0 - 127 -> | |# 00 03 | 0000 aaaa | Wave Number 0 - 254 -> | | | 0000 bbbb | (001 - 255) | | 00 05 | 0000 00aa | Wave Gain 0 - 3 *2 | | 00 06 | 0000 aaaa | Bend Range 0 - 12 | | 00 07 | 000a aaaa | Mute Group 0 - 31 (OFF,1 - 31)| | 00 08 | 0000 000a | Envelope Mode 0 - 1 *3 | | 00 09 | 0000 000a | Volume Control Switch 0 - 1 (OFF,ON) | | 00 0A | 0000 000a | Hold-1 Control Switch 0 - 1 (OFF,ON) | | 00 0B | 0000 00aa | Pan Control Switch 0 - 2 *4 | |++| | 00 0C | 0aaa aaaa | Coarse Tune 0 - 127 (C-1 - G9) | | 00 0D | 0aaa aaaa | Fine Tune 0 - 100 (-50 - +50)| | 00 0E | 000a aaaa | Random Pitch Depth 0 - 30 *5 | | 00 0F | 000a aaaa | Pitch Envelope Depth 0 - 24 (-12 - +12)| | 00 10 | 0aaa aaaa | Pitch Envelope Velocity Sens 0 - 125 *6 | | 00 11 | 0000 aaaa | Pitch Envelope Velocity Time 0 - 14 *7 | | 00 12 | 0aaa aaaa | Pitch Envelope Time 1 0 - 127 | | 00 13 | 0aaa aaaa | Pitch Envelope Time 2 0 - 127 | | 00 14 | 0aaa aaaa | Pitch Envelope Time 3 0 - 127 | | 00 15 | 0aaa aaaa | Pitch Envelope Time 4 0 - 127 | | 00 16 | 0aaa aaaa | Pitch Envelope Level 1 0 - 126 (-63 - +63)| | 00 17 | 0aaa aaaa | Pitch Envelope Level 2 0 - 126 (-63 - +63)| | 00 18 | 0aaa aaaa | Pitch Envelope Level 3 0 - 126 (-63 - +63)| | 00 19 | 0aaa aaaa | Pitch Envelope Level 4 0 - 126 (-63 - +63)| |++| | 00 1A | 0000 0aaa | Filter Type 0 - 4 *8 | | 00 1B | 0aaa aaaa | Cutoff Frequency 0 - 127 | | 00 1C | 0aaa aaaa | Resonance 0 - 127 | | 00 1D | 0aaa aaaa | Resonance Velocity Sens 0 - 125 *6 | | 00 1E | 0aaa aaaa | Filter Envelope Depth 0 - 126 (-63 - +63)| | 00 1F | 0aaa aaaa | Filter Envelope Velocity Sens 0 - 125 *6 | | 00 20 | 0000 aaaa | Filter Envelope Velocity Time 0 - 14 *7 | | 00 21 | 0aaa aaaa | Filter Envelope Time 1 0 - 127 | | 00 22 | 0aaa aaaa | Filter Envelope Time 2 0 - 127 | | 00 23 | 0aaa aaaa | Filter Envelope Time 3 0 - 127 | | 00 24 | 0aaa aaaa | Filter Envelope Time 4 0 - 127 | | 00 25 | 0aaa aaaa | Filter Envelope Level 1 0 - 127 | | 00 26 | 0aaa aaaa | Filter Envelope Level 2 0 - 127 | | 00 27 | 0aaa aaaa | Filter Envelope Level 3 0 - 127 | | 00 28 | 0aaa aaaa | Filter Envelope Level 4 0 - 127 | |++| | 00 29 | 0aaa aaaa | Tone Level 0 - 127 | | 00 2A | 0aaa aaaa | Level Envelope Velocity Sens 0 - 125 *6 | | 00 2B | 0000 aaaa | Level Envelope Velocity Time 0 - 14 *7 | | 00 2C | 0aaa aaaa | Level Envelope Time 1 0 - 127 | | 00 2D | 0aaa aaaa | Level Envelope Time 2 0 - 127 | | 00 2E | 0aaa aaaa | Level Envelope Time 3 0 - 127 | | 00 2F | 0aaa aaaa | Level Envelope Time 4 0 - 127 | | 00 30 | 0aaa aaaa | Level Envelope Level 1 0 - 127 | | 00 31 | 0aaa aaaa | Level Envelope Level 2 0 - 127 | | 00 32 | 0aaa aaaa | Level Envelope Level 3 0 - 127 | | 00 33 | 0aaa aaaa | Tone Pan 0 - 127 (L64 - 63R)| | 00 34 | 00aa aaaa | Random Pan Depth 0 - 63 | | 00 35 | 0aaa aaaa | Alternate Pan Depth 1 - 127 (L63 - 63R)| |++| | 00 36 | 0000 00aa | Output Assign 0 - 3 *9 | | 00 37 | 0aaa aaaa | Mix/EFX Send Level 0 - 127 | | 00 38 | 0aaa aaaa | Chorus Send Level 0 - 127 | | 00 39 | 0aaa aaaa | Reverb Send Level 0 - 127 | |+| |Total size | 00 00 00 3A | ++

++ | Wave Group | Group Type | Group ID | Number (value) | |+++| | INT-A | 0 | 1 | 0 - 254 (001 - 255) | | INT-B | 0 | 2 | 0 - 192 (001 - 193) | | <PCM | 1 | 1 - 127 | 0 - 254 (001 - 255)>| |XP-A(Session)| 2 | 9 | 0 - 205 (001 - 206) | | XP-B(Orch.) | 2 | 2 | 0 - 173 (001 - 174) | | XP-C(Techno)| 2 | 11 | 0 - 254 (001 - 255) | | XP-D | 2 | 1 - 127 | 0 - 254 (001 - 255) | | XP-E | 2 | 1 - 127 | 0 - 254 (001 - 255) | ++

196

MIDI Implementation

*1 *2 *3 *4 *5 *6 *7 *8 *9

INT, <PCM>, EXP -6, 0, +6, +12 NO-SUS, SUSTAIN OFF, CONTINUOUS, KEY-ON 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 20, 30, 40, 50, 60, 70, 80, 90, 100, 200, 300, 400, 500, 600, 700, 800, 900, 1000, 1100, 1200 -100+150 -100, -70, -50, -40, -30, -20, -10, 0, +10, +20, +30, +40, +50, +70, +100 OFF, LPF, BPF, HPF, PKG MIX, EFX, <DIRECT-1>, <DIRECT-2>

s Address Block Map


The following is an outline of the address map for Exclusive messages. Address(H) Block Sub Block Reference =========== ==================== =========================== ========= 00 00 00 00 ++......................................++ | System common | | 1-1-1 | ++......................................++ ++.....++.....................++ |Scale tune | | Part 1 | | 1-1-2 | ++. ++.....................++ : : . | : | : : . ++ : : . | Part 16 | : : . ++ : : . ++ : : . | Patch | : : .++ 01 00 00 00 ++.....++.....................++ | Temporary | | Common | | 1-2-1 | | performance | ++.....................++ ++. ++.....................++ : : . | Part 1 | | 1-2-2 | : : . ++.....................++ : : . | : | : : . ++ : : . | Part 16 | : : .++ 02 00 00 00 ++.....++.....++....++ | Performance mode | | Part 1 | | Common | | 1-3-1 | | temporary patch | ++. ++....++ ++.. | : | . ++....++ : : . ++ . | Tone 1 | | 132 | : : . | Part 9 | . ++....++ : : .++ . | : | : : . ++ : : . | Tone 4 | : : .++ 02 09 00 00 ++.....++.....................++ | Temporary | | Common | | 1-4-1 | | rhythm setup | ++.....................++ ++. ++.....................++ : : . | Note# 35 | | 1-4-2 | : : . ++.....................++ : : . | : | : : . ++ : : . | Note# 98 | : : .++ 02 0A 00 00 ++.....++.....++....++ | Performance mode | | Part 11 | | Common | | 1-3-1 | | temporary patch | ++. ++....++ ++.. | : | . ++....++ : : . ++ . | Tone 1 | | 132 | : : . | Part 16 | . ++....++ : : .++ . | : | : : . ++ : : . | Tone 4 | : : .++ 03 00 00 00 ++.....++.....................++ | Patch mode | | Common | | 1-3-1 | | temporary patch | ++.....................++ ++. ++.....................++ : : . | Tone 1 | | 1-3-2 | : : . ++.....................++ : : . | : | : : . ++ : : . | Tone 4 | : : .++ 10 00 00 00 ++.....++.....++....++ | User | | USER:01 | | Common | | 1-2-1 | | performance | ++. ++....++ ++.. | : | . ++....++ : : . ++ . | Part 1 | | 122 | : : . | USER:32 | . ++....++ : : .++ . | : | : : . ++ : : . | Part 16 | : : .++ 10 40 00 00 ++.....++.....++....++ | User | | USER:1 | | Common | | 1-4-1 | | rhythm setup | ++. ++....++ ++... ++ . ++....++ : : . | USER:2 | . | Note# 35 | | 1-4-2 | : : ++ . ++....++ : : . | : | : : . ++ : : . | Note# 98 | : : .++ 11 00 00 00 ++.....++.....++....++ | User | | USER:001 | | Common | | 1-3-1 | | patch | ++. ++....++ ++.. | : | . ++....++ : : . ++ . | Tone 1 | | 132 | : : . | USER:128 | . ++....++ : : .++ . | : | : : . ++ : : . | Tone 4 | : : .++

197

Appendices

MIDI Implementation

2. GS (Model ID = 42H)
++ | Start | | | address | Description | |+| | 40 10 00 | Scale Tune Part10 2-1 | | 40 11 00 | : Part1 | | 40 12 00 | : Part2 | | 40 13 00 | : Part3 | | 40 14 00 | : Part4 | | 40 15 00 | : Part5 | | 40 16 00 | : Part6 | | 40 17 00 | : Part7 | | 40 18 00 | : Part8 | | 40 19 00 | : Part9 | | 40 1A 00 | : Part11 | | 40 1B 00 | : Part12 | | 40 1C 00 | : Part13 | | 40 1D 00 | : Part14 | | 40 1E 00 | : Part15 | | 40 1F 00 | : Part16 | ++

q 2-1.Scale Tune
++ | Offset | | | Address | Description | |+| | 40 | 0aaa aaaa | Scale Tune for C 0 - 127 | | | | (-64 - +63) | | 41 | 0aaa aaaa | Scale Tune for C# 0 - 127 | | | | (-64 - +63) | | 42 | 0aaa aaaa | Scale Tune for D 0 - 127 | | | | (-64 - +63) | | 43 | 0aaa aaaa | Scale Tune for D# 0 - 127 | | | | (-64 - +63) | | 44 | 0aaa aaaa | Scale Tune for E 0 - 127 | | | | (-64 - +63) | | 45 | 0aaa aaaa | Scale Tune for F 0 - 127 | | | | (-64 - +63) | | 46 | 0aaa aaaa | Scale Tune for F# 0 - 127 | | | | (-64 - +63) | | 47 | 0aaa aaaa | Scale Tune for G 0 - 127 | | | | (-64 - +63) | | 48 | 0aaa aaaa | Scale Tune for G# 0 - 127 | | | | (-64 - +63) | | 49 | 0aaa aaaa | Scale Tune for A 0 - 127 | | | | (-64 - +63) | | 4A | 0aaa aaaa | Scale Tune for A# 0 - 127 | | | | (-64 - +63) | | 4B | 0aaa aaaa | Scale Tune for B 0 - 127 | | | | (-64 - +63) | |+| |Total Size | 00 00 0C | ++ * In order for a GS Exclusive message to be correctly received by the XP-30, the starting address of the message must be the Start address of each Part (the address of Scale Tune C, i.e., offset 40).

198

MIDI Implementation

4. Supplementary Material
s Correspondence of the EFX Algorithm and Exclusive Address (EFX Parameter 112)
EFX | Parameter | Value ++

q Type09: COMPRESSOR
++ prm1 | Sustain | 0 - 127 prm2 | Attack | 0 - 127 prm3 | Output Pan | 0 - 127 prm4 | Post Gain | 0 - 3 prm5 | Low Gain | 0 - 30 prm6 | HiGH Gain | 0 - 30 prm7 | Output Level | 0 - 127

q Type10: LIMITER
++ prm1 | Threshold Level | 0 - 127 prm2 | Release Time | 0 - 127 prm3 | Compression Ratio | 0 - 3 prm4 | Output Pan | 0 - 127 prm5 | Post Gain | 0 - 3 prm6 | Low Gain | 0 - 30 prm7 | High Gain | 0 - 30 prm8 | Output Level | 0 - 127

q Type01: STEREO-EQ
++ prm1 | Low Frequency | 0 - 1 prm2 | Low Gain | 0 - 30 prm3 | High Frequency | 0 - 1 prm4 | High Gain | 0 - 30 prm5 | Peaking1 Frequency | 0 - 16 prm6 | Peaking1 Q | 0 - 4 prm7 | Peaking1 Gain | 0 - 30 prm8 | Peaking2 Frequency | 0 - 16 prm9 | Peaking2 Q | 0 - 4 prm10 | Peaking2 Gain | 0 - 30 prm11 | Level | 0 - 127

q Type11: HEXA-CHORUS
++ prm1 | Pre Delay Time | 0 - 125 prm2 | Rate | 0 - 125 prm3 | Depth | 0 - 127 prm4 | Pre Delay Deviation | 0 - 20 prm5 | Depth Deviation | 0 - 40 prm6 | Pan Deviation | 0 - 20 prm7 | Effect Balance | 0 - 100 prm8 | Output Level | 0 - 127

q Type02: OVERDRIVE
++ prm1 | Drive | 0 - 127 prm2 | Output Pan | 0 - 127 prm3 | Amp Simulator Type | 0 - 3 prm4 | Low Gain | 0 - 30 prm5 | High Gain | 0 - 30 prm6 | Output Level | 0 - 127

q Type12: TREMOLO-CHORUS
++ prm1 | Pre Delay Time | 0 - 125 prm2 | Chorus Rate | 0 - 125 prm3 | Chorus Depth | 0 - 127 prm4 | Tremolo Rate | 0 - 125 prm5 | Tremolo Separation | 0 - 127 prm6 | Tremolo Phase | 0 - 90 prm7 | Effect Balance | 0 - 100 prm8 | Output Level | 0 - 127

q Type03: DISTORTION
++ prm1 | Drive | 0 - 127 prm2 | Output Pan | 0 - 127 prm3 | Amp Simulator Type | 0 - 3 prm4 | Low Gain | 0 - 30 prm5 | High Gain | 0 - 30 prm6 | Output Level | 0 - 127

q Type04: PHASER
++ prm1 | Manual | 0 - 125 prm2 | Rate | 0 - 125 prm3 | Depth | 0 - 127 prm4 | Resonance | 0 - 127 prm5 | Mix Level | 0 - 127 prm6 | Output Pan | 0 - 127 prm7 | Output Level | 0 - 127

q Type13: SPACE-D
++ prm1 | Pre Delay Time | 0 - 125 prm2 | Rate | 0 - 125 prm3 | Depth | 0 - 127 prm4 | Phase | 0 - 90 prm5 | Low Gain | 0 - 30 prm6 | High Gain | 0 - 30 prm7 | Effect Balance | 0 - 100 prm8 | Output Level | 0 - 127

q Type05: SPECTRUM
++ prm1 | Band1 Gain | 0 - 30 prm2 | Band2 Gain | 0 - 30 prm3 | Band3 Gain | 0 - 30 prm4 | Band4 Gain | 0 - 30 prm5 | Band5 Gain | 0 - 30 prm6 | Band6 Gain | 0 - 30 prm7 | Band7 Gain | 0 - 30 prm8 | Band8 Gain | 0 - 30 prm9 | Q | 0 - 4 prm10 | Output Pan | 0 - 127 prm11 | Output Level | 0 - 127

q Type14: STEREO-CHORUS
++ prm1 | Filter Type | 0 - 2 prm2 | Cutoff Frequency | 0 - 16 prm3 | Pre Delay Time | 0 - 125 prm4 | Rate | 0 - 125 prm5 | Depth | 0 - 127 prm6 | Phase | 0 - 90 prm7 | (not used) | prm8 | Low Gain | 0 - 30 prm9 | High Gain | 0 - 30 prm10 | Effect Balance | 0 - 100 prm11 | Output Level | 0 - 127

q Type06: ENHANCER
++ prm1 | Sens | 0 - 127 prm2 | Mix Level | 0 - 127 prm3 | Low Gain | 0 - 30 prm4 | High Gain | 0 - 30 prm5 | Output Level | 0 - 127

q Type15: STEREO-FLANGER
++ prm1 | Filter Type | 0 - 2 prm2 | Cutoff Frequency | 0 - 16 prm3 | Pre Delay Time | 0 - 125 prm4 | Rate | 0 - 125 prm5 | Depth | 0 - 127 prm6 | Phase | 0 - 90 prm7 | Feedback Level | 0 - 98 prm8 | Low Gain | 0 - 30 prm9 | High Gain | 0 - 30 prm10 | Effect Balance | 0 - 100 prm11 | Output Level | 0 - 127

q Type07: AUTO-WAH
++ prm1 | Filter Type | 0 - 1 prm2 | Rate | 0 - 125 prm3 | Depth | 0 - 127 prm4 | Sens | 0 - 127 prm5 | Manual | 0 - 127 prm6 | Peak | 0 - 127 prm7 | Output Level | 0 - 127

q Type16: STEP-FLANGER

q Type08: ROTARY
++ prm1 | High Frequency Slow Rate | 0 - 125 prm2 | Low Frequency Slow Rate | 0 - 125 prm3 | High Frequency Fast Rate | 0 - 125 prm4 | Low Frequency Fast Rate | 0 - 125 prm5 | Speed | 0 - 1 prm6 | High Frequency Acceleration | 0 - 15 prm7 | Low Frequency Acceleration | 0 - 15 prm8 | High Frequency Level | 0 - 127 prm9 | Low Frequency Level | 0 - 127 prm10 | Separation | 0 - 127 prm11 | Output Level | 0 - 127

199

Appendices

++ prm1 | Pre Delay Time | 0 - 125 prm2 | Rate | 0 - 125 prm3 | Depth | 0 - 127 prm4 | Feedback Level | 0 - 98 prm5 | Step Rate | 0 - 125 prm6 | Phase | 0 - 90 prm7 | Low Gain | 0 - 30 prm8 | High Gain | 0 - 30 prm9 | Effect Balance | 0 - 100 prm10 | Output Level | 0 - 127

MIDI Implementation

q Type17: STEREO-DELAY
++ prm1 | Feedback Mode | 0 - 1 prm2 | Delay Time Left | 0 - 126 prm3 | Delay Time Right | 0 - 126 prm4 | Feedback Phase Left | 0 - 1 prm5 | Feedback Phase Right | 0 - 1 prm6 | Feedback Level | 0 - 98 prm7 | HF Damp | 0 - 17 prm8 | Low Gain | 0 - 30 prm9 | High Gain | 0 - 30 prm10 | Effect Balance | 0 - 100 prm11 | Output Level | 0 - 127

q Type24: REVERB
++ prm1 | Reverb Type | 0 - 5 prm2 | Pre Delay Time | 0 - 125 prm3 | Gate Time | 0 - 127 prm4 | HF Damp | 0 - 17 prm5 | Low Gain | 0 - 30 prm6 | High Gain | 0 - 30 prm7 | Effect Balance | 0 - 100 prm8 | Output Level | 0 - 127

q Type25: GATE-REVERB
++ prm1 | Gate-Reverb Type | 0 - 3 prm2 | Pre Delay Time | 0 - 125 prm3 | Gate Time | 0 - 99 prm4 | Low Gain | 0 - 30 prm5 | High Gain | 0 - 30 prm6 | Effect Balance | 0 - 100 prm7 | Output Level | 0 - 127

q Type18: MODULATION-DELAY
++ prm1 | Feedback Mode | 0 - 1 prm2 | Delay Time Left | 0 - 126 prm3 | Delay Time Right | 0 - 126 prm4 | Feedback Level | 0 - 98 prm5 | HF Damp | 0 - 17 prm6 | Rate | 0 - 125 prm7 | Depth | 0 - 127 prm8 | Phase | 0 - 90 prm9 | Low Gain | 0 - 30 prm10 | High Gain | 0 - 30 prm11 | Effect Balance | 0 - 100 prm12 | Output Level | 0 - 127

q Type26: OVERDRIVECHORUS
++ prm1 | Drive | 0 - 127 prm2 | Over Drive Pan | 0 - 127 prm3 | Chorus Pre Delay Time | 0 - 125 prm4 | Chorus Rate | 0 - 125 prm5 | Chorus Depth | 0 - 127 prm6 | (not used) | prm7 | Chorus Balance | 0 - 100 prm8 | Output Level | 0 - 127

q Type19: TRIPLE-TAP-DELAY
++ prm1 | Delay Time Left | 0 - 125 prm2 | Delay Time Right | 0 - 125 prm3 | Delay Time Center | 0 - 125 prm4 | Feedback Level | 0 - 98 prm5 | HF Damp | 0 - 17 prm6 | Left Level | 0 - 127 prm7 | Right Level | 0 - 127 prm8 | Center Level | 0 - 127 prm9 | Low Gain | 0 - 30 prm10 | High Gain | 0 - 30 prm11 | Effect Balance | 0 - 100 prm12 | Output Level | 0 - 127

q Type27: OVERDRIVEFLANGER (serial)


++ prm1 | Drive | 0 - 127 prm2 | Over Drive Pan | 0 - 127 prm3 | Flanger Pre Delay Time | 0 - 125 prm4 | Flanger Rate | 0 - 125 prm5 | Flanger Depth | 0 - 127 prm6 | Flanger Feedback Level | 0 - 98 prm7 | Flanger Balance | 0 - 100 prm8 | Output Level | 0 - 127

q Type20: QUADRUPLE-TAP-DELAY
++ prm1 | Delay Time 1 | 0 - 125 prm2 | Delay Time 2 | 0 - 125 prm3 | Delay Time 3 | 0 - 125 prm4 | Delay Time 4 | 0 - 125 prm5 | Level 1 | 0 - 127 prm6 | Level 2 | 0 - 127 prm7 | Level 3 | 0 - 127 prm8 | Level 4 | 0 - 127 prm9 | Feedback Level | 0 - 98 prm10 | HF Damp | 0 - 17 prm11 | Effect Balance | 0 - 100 prm12 | Output Level | 0 - 127

q Type28: OVERDRIVEDELAY (serial)


++ prm1 | Drive | 0 - 127 prm2 | Over Drive Pan | 0 - 127 prm3 | Delay Time | 0 - 126 prm4 | Delay Feedback Level | 0 - 98 prm5 | Delay HF Damp | 0 - 17 prm6 | Delay Balance | 0 - 100 prm7 | Output Level | 0 - 127

q Type29: DISTORTIONCHORUS (serial)


++ prm1 | Distortion Drive | 0 - 127 prm2 | Distortion Pan | 0 - 127 prm3 | Chorus Pre Delay Time | 0 - 125 prm4 | Chorus Rate | 0 - 125 prm5 | Chorus Depth | 0 - 127 prm6 | (not used) | prm7 | Chorus Balance | 0 - 100 prm8 | Output Level | 0 - 127

q Type21: TIME-CONTROL-DELAY
++ prm1 | Delay Time | 0 - 120 prm2 | Feedback Level | 0 - 98 prm3 | Acceleration | 0 - 15 prm4 | HF Damp | 0 - 17 prm5 | Output Pan | 0 - 127 prm6 | Low Gain | 0 - 30 prm7 | High Gain | 0 - 30 prm8 | Effect Balance | 0 - 100 prm9 | Output Level | 0 - 127

q Type30: DISTORTIONFLANGER (serial)


++ prm1 | Distortion Drive | 0 - 127 prm2 | Distortion Pan | 0 - 127 prm3 | Flanger Pre Delay Time | 0 - 125 prm4 | Flanger Rate | 0 - 125 prm5 | Flanger Depth | 0 - 127 prm6 | Flanger Feedback Level | 0 - 98 prm7 | Flanger Balance | 0 - 100 prm8 | Output Level | 0 - 127

q Type22: 2VOICE-PITCH-SHIFTER
++ prm1 | Pitch Shifter Mode | 0 - 4 prm2 | Coarse Pitch A | 0 - 36 prm3 | Coarse Pitch B | 0 - 36 prm4 | Fine Pitch A | 0 - 100 prm5 | Fine Pitch B | 0 - 100 prm6 | Pre Delay Time A | 0 - 126 prm7 | Pre Delay Time B | 0 - 126 prm8 | Output Pan A | 0 - 127 prm9 | Output Pan B | 0 - 127 prm10 | Level Balance | 0 - 100 prm11 | Effect Balance | 0 - 100 prm12 | Output Level | 0 - 127

q Type31: DISTORTIONDELAY (serial)


++ prm1 | Distortion Drive | 0 - 127 prm2 | Distortion Pan | 0 - 127 prm3 | Delay Time | 0 - 126 prm4 | Delay Feedback Level | 0 - 98 prm5 | Delay HF Damp | 0 - 17 prm6 | Delay Balance | 0 - 100 prm7 | Output Level | 0 - 127

q Type23: FBK-PITCH-SHIFTER
++ prm1 | Pitch Shifter Mode | 0 - 4 prm2 | Coarse Pitch | 0 - 36 prm3 | Fine Pitch | 0 - 100 prm4 | Pre Delay Time | 0 - 126 prm5 | Feedback Level | 0 - 98 prm6 | Output Pan | 0 - 127 prm7 | Low Gain | 0 - 30 prm8 | High Gain | 0 - 30 prm9 | Effect Balance | 0 - 100 prm10 | Output Level | 0 - 127

q Type32: ENHANCERCHORUS (serial)


++ prm1 | Enhancer Sens | 0 - 127 prm2 | Enhancer Mix Level | 0 - 127 prm3 | Chorus Pre Delay Time | 0 - 125 prm4 | Chorus Rate | 0 - 125 prm5 | Chorus Depth | 0 - 127 prm6 | (not used) | prm7 | Chorus Balance | 0 - 100 prm8 | Output Level | 0 - 127

200

MIDI Implementation

q Type33: ENHANCERFLANGER (serial)


++ prm1 | Enhancer Sens | 0 - 127 prm2 | Enhancer Mix Level | 0 - 127 prm3 | Flanger Pre Delay Time | 0 - 125 prm4 | Flanger Rate | 0 - 125 prm5 | Flanger Depth | 0 - 127 prm6 | Flanger Feedback Level | 0 - 98 prm7 | Flanger Balance | 0 - 100 prm8 | Output Level | 0 - 127

q Type34: ENHANCERDELAY (serial)


++ prm1 | Enhancer Sens | 0 - 127 prm2 | Enhancer Mix Level | 0 - 127 prm3 | Delay Time | 0 - 126 prm4 | Delay Feedback Level | 0 - 98 prm5 | Delay HF Damp | 0 - 17 prm6 | (not used) | prm7 | Delay Balance | 0 - 100 prm8 | Output Level | 0 - 127

q Type35: CHORUSDELAY (serial)


++ prm1 | Chorus Pre Delay Time | 0 - 125 prm2 | Chorus Rate | 0 - 125 prm3 | Chorus Depth | 0 - 127 prm4 | (not used) | prm5 | Chorus Balance | 0 - 100 prm6 | Delay Time | 0 - 126 prm7 | Delay Feedback Level | 0 - 98 prm8 | Delay HF Damp | 0 - 17 prm9 | Delay Balance | 0 - 100 prm10 | Output Level | 0 - 127

q Type36: FLANGERDELAY (serial)


++ prm1 | Flanger Pre Delay Time | 0 - 125 prm2 | Flanger Rate | 0 - 125 prm3 | Flanger Depth | 0 - 127 prm4 | Flanger Feedback Level | 0 - 98 prm5 | Flanger Balance | 0 - 100 prm6 | Delay Time | 0 - 126 prm7 | Delay Feedback Level | 0 - 98 prm8 | Delay HF Damp | 0 - 17 prm9 | Delay Balance | 0 - 100 prm10 | Output Level | 0 - 127

q Type37: CHORUSFLANGER (serial)


++ prm1 | Chorus Pre Delay Time | 0 - 125 prm2 | Chorus Rate | 0 - 125 prm3 | Chorus Depth | 0 - 127 prm4 | Chorus Balance | 0 - 100 prm5 | Flanger Pre Delay Time | 0 - 125 prm6 | Flanger Rate | 0 - 125 prm7 | Flanger Depth | 0 - 127 prm8 | Flanger Feedback Level | 0 - 98 prm9 | Flanger Balance | 0 - 100 prm10 | Output Level | 0 - 127

q Type38: CHORUS/DELAY (parallel)


++ prm1 | Chorus Pre Delay Time | 0 - 125 prm2 | Chorus Rate | 0 - 125 prm3 | Chorus Depth | 0 - 127 prm4 | (not used) | prm5 | Chorus Balance | 0 - 100 prm6 | Delay Time | 0 - 126 prm7 | Delay Feedback Level | 0 - 98 prm8 | Delay HF Damp | 0 - 17 prm9 | Delay Balance | 0 - 100 prm10 | Output Level | 0 - 127

q Type39: FLANGER/DELAY (parallel)


++ prm1 | Flanger Pre Delay Time | 0 - 125 prm2 | Flanger Rate | 0 - 125 prm3 | Flanger Depth | 0 - 127 prm4 | Flanger Feedback Level | 0 - 98 prm5 | Flanger Balance | 0 - 100 prm6 | Delay Time | 0 - 126 prm7 | Delay Feedback Level | 0 - 98 prm8 | Delay HF Damp | 0 - 17 prm9 | Delay Balance | 0 - 100 prm10 | Output Level | 0 - 127

q Type40: CHORUS/FLANGER (parallel)


++ prm1 | Chorus Pre Delay Time | 0 - 125 prm2 | Chorus Rate | 0 - 125 prm3 | Chorus Depth | 0 - 127 prm4 | Chorus Balance | 0 - 100 prm5 | Flanger Pre Delay Time | 0 - 125 prm6 | Flanger Rate | 0 - 125 prm7 | Flanger Depth | 0 - 127 prm8 | Flanger Feedback Level | 0 - 98 prm9 | Flanger Balance | 0 - 100 prm10 | Output Level | 0 - 127

201

Appendices

MIDI Implementation

s List of the Arpeggio Parameter


q Arpeggio Style
++++ |value| parameter |value| parameter |value| parameter | ++++ | 0 | 1/ 4 | 15 | RHYTHM GTR A | 30 | BOUND BOLL | | 1 | 1/ 6 | 16 | RHYTHM GTR B | 31 | RANDOM | | 2 | 1/ 8 | 17 | RHYTHM GTR C | 32 | LIMITLESS | | 3 | 1/12 | 18 | RHYTHM GTR D | 33 | PORTAMENTO A | | 4 | 1/16 | 19 | RHYTHM GTR E | 34 | PORTAMENTO B | | 5 | 1/32 | 20 | 3 FINGER GTR | 35 | SEQUENCE D | | 6 | GLISSANDO | 21 | STRUMMING GTR | 36 | BOSSA NOVA | | 7 | SEQUENCE A | 22 | KBD COMPING A | 37 | SALSA | | 8 | SEQUENCE B | 23 | KBD COMPING B | 38 | MAMBO | | 9 | SEQUENCE C | 24 | KBD COMPING C | 39 | LATIN PERCUSSION | | 10 | ECHO | 25 | KBD COMPING D | 40 | SAMBA | | 11 | SYNTH BASS | 26 | KBD COMPING E | 41 | TANGO | | 12 | SLAP BASS A | 27 | PERCUSSION | 42 | HOUSE | | 13 | SLAP BASS B | 28 | HARP | | | | 14 | WALK BASS | 29 | SHAMISEN | | | ++++

q Arpeggio Motif
++++ |value| parameter |value| parameter |value| parameter | ++++ | 0 | SINGLE UP | 13 | BASS+CHORD 3 | 26 | BASS+RANDOM 3 | | 1 | SINGLE DOWN | 14 | BASS+CHORD 4 | 27 | TOP+UP 1 | | 2 | SINGLE UP&DOWN | 15 | BASS+CHORD 5 | 28 | TOP+UP 2 | | 3 | SINGLE RANDOM | 16 | BASS+UP 1 | 29 | TOP+UP 3 | | 4 | DUAL UP | 17 | BASS+UP 2 | 30 | TOP+UP 4 | | 5 | DUAL DOWN | 18 | BASS+UP 3 | 31 | TOP+UP 5 | | 6 | DUAL UP&DOWN | 19 | BASS+UP 4 | 32 | TOP+UP 6 | | 7 | DUAL RANDOM | 20 | BASS+UP 5 | 33 | BASS+UP+TOP | | 8 | NOTE ORDER | 21 | BASS+UP 6 | 34 | TRIPLE UP | | 9 | GLISSANDO | 22 | BASS+UP 7 | 35 | TRIPLE DOWN | | 10 | CHORD | 23 | BASS+UP 8 | 36 | TRIPLE UP&DOWN | | 11 | BASS+CHORD 1 | 24 | BASS+RANDOM 1 | 37 | TRIPLE RANDOM | | 12 | BASS+CHORD 2 | 25 | BASS+RANDOM 2 | | | ++++

q Arpeggio Beat Pattern


++++ |value| parameter |value| parameter |value| parameter | ++++ | 0 | 1/ 4 | 40 | MUTE 15 | 80 | PORTA-B 09 | | 1 | 1/ 6 | 41 | MUTE 16 | 81 | PORTA-B 10 | | 2 | 1/ 8 | 42 | STRUM 1 | 82 | PORTA-B 11 | | 3 | 1/12 | 43 | STRUM 2 | 83 | PORTA-B 12 | | 4 | 1/16 1 | 44 | STRUM 3 | 84 | PORTA-B 13 | | 5 | 1/16 2 | 45 | STRUM 4 | 85 | PORTA-B 14 | | 6 | 1/16 3 | 46 | STRUM 5 | 86 | PORTA-B 15 | | 7 | 1/32 1 | 47 | STRUM 6 | 87 | SEQ-B 5 | | 8 | 1/32 2 | 48 | STRUM 7 | 88 | SEQ-D 1 | | 9 | 1/32 3 | 49 | STRUM 8 | 89 | SEQ-D 2 | | 10 | SEQ-A 1 | 50 | REGGAE1 | 90 | SEQ-D 3 | | 11 | SEQ-A 2 | 51 | REFRAIN1 | 91 | SEQ-D 4 | | 12 | SEQ-A 3 | 52 | REFRAIN2 | 92 | SEQ-D 5 | | 13 | SEQ-A 4 | 53 | PERC1 | 93 | SEQ-D 6 | | 14 | SEQ-A 5 | 54 | PERC2 | 94 | SEQ-D 7 | | 15 | SEQ-A 6 | 55 | PERC3 | 95 | SEQ-D 8 | | 16 | SEQ-A 7 | 56 | PERC4 | 96 | REGGAE2 | | 17 | SEQ-B 1 | 57 | WALKBS | 97 | BOSSA NOVA | | 18 | SEQ-B 2 | 58 | HARP | 98 | SALSA 1 | | 19 | SEQ-B 3 | 59 | BOUND | 99 | SALSA 2 | | 20 | SEQ-B 4 | 60 | RANDOM | 100 | SALSA 3 | | 21 | SEQ-C 1 | 61 | PORTA-A 01 | 101 | SALSA 4 | | 22 | SEQ-C 2 | 62 | PORTA-A 02 | 102 | MAMBO 1 | | 23 | ECHO 1 | 63 | PORTA-A 03 | 103 | MAMBO 2 | | 24 | ECHO 2 | 64 | PORTA-A 04 | 104 | CLAVE | | 25 | ECHO 3 | 65 | PORTA-A 05 | 105 | REV CLA | | 26 | MUTE 01 | 66 | PORTA-A 06 | 106 | GUIRO | | 27 | MUTE 02 | 67 | PORTA-A 07 | 107 | AGOGO | | 28 | MUTE 03 | 68 | PORTA-A 08 | 108 | SAMBA | | 29 | MUTE 04 | 69 | PORTA-A 09 | 109 | TANGO 1 | | 30 | MUTE 05 | 70 | PORTA-A 10 | 110 | TANGO 2 | | 31 | MUTE 06 | 71 | PORTA-A 11 | 111 | TANGO 3 | | 32 | MUTE 07 | 72 | PORTA-B 01 | 112 | TANGO 4 | | 33 | MUTE 08 | 73 | PORTA-B 02 | 113 | HOUSE 1 | | 34 | MUTE 09 | 74 | PORTA-B 03 | 114 | HOUSE 2 | | 35 | MUTE 10 | 75 | PORTA-B 04 | | | | 36 | MUTE 11 | 76 | PORTA-B 05 | | | | 37 | MUTE 12 | 77 | PORTA-B 06 | | | | 38 | MUTE 13 | 78 | PORTA-B 07 | | | | 39 | MUTE 14 | 79 | PORTA-B 08 | | | ++++

202

MIDI Implementation

s Decimal/Hexadecimal Table (hexadecimal values are indicated by a following H)


MIDI uses 7-bit hexadecimal values to indicate data values and the address and size of exclusive messages. The following table shows the correspondence between decimal and hexadecimal numbers. ++++++++++++ | D | H || D | H || D | H || D | H | ++++++++++++ | 0 | 00H || 32 | 20H || 64 | 40H || 96 | 60H | | 1 | 01H || 33 | 21H || 65 | 41H || 97 | 61H | | 2 | 02H || 34 | 22H || 66 | 42H || 98 | 62H | | 3 | 03H || 35 | 23H || 67 | 43H || 99 | 63H | | 4 | 04H || 36 | 24H || 68 | 44H || 100 | 64H | | 5 | 05H || 37 | 25H || 69 | 45H || 101 | 65H | | 6 | 06H || 38 | 26H || 70 | 46H || 102 | 66H | | 7 | 07H || 39 | 27H || 71 | 47H || 103 | 67H | | 8 | 08H || 40 | 28H || 72 | 48H || 104 | 68H | | 9 | 09H || 41 | 29H || 73 | 49H || 105 | 69H | | 10 | 0AH || 42 | 2AH || 74 | 4AH || 106 | 6AH | | 11 | 0BH || 43 | 2BH || 75 | 4BH || 107 | 6BH | | 12 | 0CH || 44 | 2CH || 76 | 4CH || 108 | 6CH | | 13 | 0DH || 45 | 2DH || 77 | 4DH || 109 | 6DH | | 14 | 0EH || 46 | 2EH || 78 | 4EH || 110 | 6EH | | 15 | 0FH || 47 | 2FH || 79 | 4FH || 111 | 6FH | | 16 | 10H || 48 | 30H || 80 | 50H || 112 | 70H | | 17 | 11H || 49 | 31H || 81 | 51H || 113 | 71H | | 18 | 12H || 50 | 32H || 82 | 52H || 114 | 72H | | 19 | 13H || 51 | 33H || 83 | 53H || 115 | 73H | | 20 | 14H || 52 | 34H || 84 | 54H || 116 | 74H | | 21 | 15H || 53 | 35H || 85 | 55H || 117 | 75H | | 22 | 16H || 54 | 36H || 86 | 56H || 118 | 76H | | 23 | 17H || 55 | 37H || 87 | 57H || 119 | 77H | | 24 | 18H || 56 | 38H || 88 | 58H || 120 | 78H | | 25 | 19H || 57 | 39H || 89 | 59H || 121 | 79H | | 26 | 1AH || 58 | 3AH || 90 | 5AH || 122 | 7AH | | 27 | 1BH || 59 | 3BH || 91 | 5BH || 123 | 7BH | | 28 | 1CH || 60 | 3CH || 92 | 5CH || 124 | 7CH | | 29 | 1DH || 61 | 3DH || 93 | 5DH || 125 | 7DH | | 30 | 1EH || 62 | 3EH || 94 | 5EH || 126 | 7EH | | 31 | 1FH || 63 | 3FH || 95 | 5FH || 127 | 7FH | ++++++++++++ D: decimal H: hexadecimal * * Decimal expressions such as used for MIDI channel, Bank Select, and Program Change will be the value 1 greater than the decimal value given in the above table. Since each MIDI byte carries 7 significant data bits, each byte can express a maximum of 128 different values. Data for which higher resolution is required must be transmitted using two or more bytes. For example a value indicated as a two-byte value of aa bbH would have a value of aa x 128 + bb. For a signed number (+/-), 00H = -64, 40H = +/-0, and 7FH = +63. I.e., the decimal equivalent will be 64 less than the decimal value given in the above table. For a two-byte signed number, 00 00H = -8192, 40 00H = +/-0, and 7F 7FH = +8191. For example the decimal expression of aa bbH would be aa bbH - 40 00H = (aa x 128 + bb - 64 x 128. Hexadecimal notation in two 4-bit units is used for data indicated as nibbled. The nibbled two-byte value of 0a 0b H would be a x 16 + b.

s Examples of Actual MIDI Messages


<Example 1> 92 3E 5F 9n is the Note On status and `n' is the MIDI channel number. Since 2H = 2, 3EH = 62, and 5FH = 95, this is a Note On message of MIDI CH = 3, note number 62 (note name D4) and velocity 95. <Example 2> CE 49 CnH is the Program Change status and `n' is the MIDI channel number. Since EH = 14, and 49H = 73, this is a Program Change message of MIDI CH = 15, Program number 74 (in the GS sound map, Flute). <Example 3> EA 00 28 EnH is the Pitch Bend Change status and `n' is the MIDI channel number. The 2nd byte (00H=0) is the LSB of the Pitch Bend value, and the 3rd byte (28H=40) is the MSB. However since the Pitch Bend is a signed number with 0 at 40 00H ( = 64 x 128 + 0 = 8192), the Pitch Bend value in this case is 28 00H - 40 00H = 40 x 128 + 0 - (64 x 128 + 0) = 5120 - 8192 = -3072 If we assume that the Pitch Bend Sensitivity is set to two semitones, the pitch will change only -200 cents for a Pitch Bend value of -8192 (00 00H). Thus, this message is specifying a Pitch Bend of -200 x (-3072) / (-8192) = -75 cents on MIDI CH = 11. <Example 4> B3 64 00 65 00 06 0C 26 00 64 7F 65 7F BnH is the Control Change status, and `n' is the MIDI channel number. In Control Change messages, the 2nd byte is the controller number, and the 3rd byte is the parameter value. MIDI allows what is known as running status, when if messages of the the same status follow each other, it is permitted to omit the second and following status bytes. In the message above, running status is being used, meaning that the message has the following content. B3 64 00 (B3) 65 00 (B3) 06 0C (B3) 26 00 (B3) 64 7F (B3) 65 7F MIDI CH = 4, RPN parameter number LSB: 00H MIDI CH = 4, RPN parameter number MSB: 00H MIDI CH = 4, parameter value MSB: 0CH MIDI CH = 4, parameter value LSB: 00H MIDI CH = 4, RPN parameter number LSB: 7FH MIDI CH = 4, RPN parameter number MSB: 7FH

Thus, this message transmits a parameter value of 0C 00H to RPN parameter number 00 00H on MIDI CH = 4, and then sets the RPN parameter number to 7F 7FH.

The function assigned to RPN parameter number 00 00H is Pitch Bend Sensitivity, and the MSB of the parameter value indicates semitone steps. Since the MSB of this parameter value is 0CH = 12, the maximum width of pitch bend is being set to [+-]12 semitones (1 octave) (GS sound sources ignore the LSB of Pitch Bend Sensitivity, but it is best to transmit the LSB (parameter value 0) as well, so that the message can be correctly received by any device. Once the parameter number has been set for RPN or NRPN, all subsequent Data Entry messages on that channel will be effective. Thus, it is recommended that after you have made the change you want, you set the parameter number to 7F 7FH (an unset or null setting). The final (B3) 64 7F (B3) 65 7F is for this purpose. It is not a good idea to store many events within the data of a song (e.g., a Standard MIDI File song) using running status as shown in <Example 4>. When the song is paused, fastforwarded or rewound, the sequencer may not be able to transmit the proper status, causing the sound source to misinterpret the data. It is best to attach the proper status byte to all events. It is also important to transmit RPN or NRPN parameter number settings and parameter values in the correct order. In some sequencers, data events recorded in the same clock (or a nearby clock) can sometimes be transmitted in an order other than the order in which they were recorded. It is best to record such events at an appropriate interval (1 tick at TPQN=96, or 5 ticks at TPQN=480). * TPQN: Ticks Per Quarter Note (i.e., the time resolution of the sequencer)

<Example 1> What is the decimal equivalent of 5AH? From the above table, 5AH = 90. <Example 2> What is the decimal equivalent of the 7-bit hexadecimal values 12 34H? From the above table, 12H = 18 and 34H = 52 Thus, 18 x 128 + 52 = 2356 <Example 3> What is the decimal equivalent of the nibbled expression 0A 03 09 0DH? From the above table, 0AH = 10, 03H = 3, 09H = 9, 0DH = 13 Thus, the result is ((10 x 16 + 3) x 16 + 9) x 16 + 13 = 41885 <Example 4> What is the nibbled equivalent of the decimal number 1258? 16 ) 1258 16 ) 78...10 16 ) 4...14 0... 4 From the above table, 0=00H, 4=04H, 14=0EH, 10=0AH Thus the result is 00 04 0E 0AH

203

Appendices

MIDI Implementation

s Examples of Exclusive Messages and Calculating the Checksum


Roland exclusive messages (RQ1, DT1) are transmitted with a checksum at the end of the data (before F7) to check that the data was received correctly. The value of the checksum is determined by the address and data (or size) of the exclusive message.

<Example 3> Retrieving data for Temporary Performance (RQ1) * When a data transfer is executed in Utility mode, data that is accessed will be the same as that which is transmitted when the Type parameter is set to PERFORM and the Source parameter is set to TEMP: -PATCH The Parameter Address Map gives the following start addresses for Temporary Performance data. 01 00 00 00H 01 00 10 00H : 01 00 1F 00H Temporary Performance Common Temporary Performance Part 1 Temporary Performance Part 16

q How to Calculate the Checksum (hexadecimal values are indicated by a H)


The checksum consists of a value whose lower 7 bits are 0 when the address, size and checksum itself are added. The following formula shows how to calculate the checksum when the exclusive message to be transmitted has an address of aa bb cc ddH, and data or size of ee ffH. aa + bb + cc + dd + ee + ff = total total / 128 = quotient ... remainder 128 - remainder = checksum <Example 1> Setting the Performance Common REVERB TYPE to DELAY (DT1) The Parameter address map indicates that the starting address of the Temporary Performance is 01 00 00 00H, that the Performance Common offset address is 00 00H, and that the REVERB TYPE address is 00 28H. Thus, the address is: 01 00 00 00 00 01 00 00 00H 00H 28H 28H

Since Performance Part has a size of 00 00 00 19H, we add that size to the start address of the Temporary Performance Part 16, resulting in: 01 00 1F 00H +) 00 00 00 19H 01 00 1F 19H Thus, the Size for the retrieved data will be: 01 00 1F 19H -) 01 00 00 00H 00 00 1F 19H F0 (1) 41 (2) 10 (3) 6A (4) 11 (5) 01 00 00 00 address 00 00 1F 19 size ?? checksum F7 (6)

+)

Since DELAY is parameter value 06H, F0 (1) 41 (2) 10 (3) 6A (4) 12 (5) 01 00 00 28 address 06 data ?? checksum F7 (6)

(1) Exclusive status (4) Model ID (XP-30)

(2) ID number (Roland) (5) Command ID (RQ1)

(3) Device ID (17) (6) EOX

Calculating the checksum as shown in <Example 2>, we get a message of F0 41 10 6A 11 01 00 00 00 00 00 1F 19 47 F7 to be transmitted. <Example 4> Retrieving the Temporary Performance data together with all Temporary Part and Rhythm Set data (RQ1) * When a data transfer is executed in Utility mode, the data that is accessed will be the same as that which is transmitted when the Type parameter is set to PERFORM and the Source parameter is set to TEMP: +PATCH The Parameter Address Map gives the following start addresses for Temporary Performance, Performance Mode Temporary Patch and Performance Mode Temporary Rhythm. 01 00 00 00H Temporary Performance 02 00 00 00H Performance Mode Temporary Patch(part 1) : 02 08 00 00H Performance Mode Temporary Patch(part 9) 02 09 00 00H Temporary Rhythm Setup 02 0A 00 00H Performance Mode Temporary Patch(part 11) : 02 0F 00 00H Performance Mode Temporary Patch(part 16) The Patch offset addresses are as follows. 00 00H Patch Common 10 00H Patch Tone 1 : 16 00H Patch Tone 4 Since Patch Tone has a size of 00 00 01 01H, we add this size to the start address of Performance Mode Temporary Patch (Part 16) Tone 4, to get: 02 0F 00 16 +) 00 00 01 02 0F 17 00H 00H 01H 01H

(1) Exclusive status (4) Model ID (XP-30)

(2) ID number (Roland) (5) Command ID (DT1)

(3) Device ID (17) (6) EOX

Next we calculate the checksum. 01H + 00H + 00H + 28H + 06H = 1 + 0 + 0 + 40 + 6 = 47 (sum) 47 (total) / 128 = 0 (quotient) ... 47 (remainder) checksum = 128 - 47 (quotient) = 81 = 51H This means that the message transmitted will be F0 41 10 6A 12 01 00 00 28 06 51 F7. <Example 2> Retrieving data for USER:03 Performance Part 3 (RQ1) The Parameter Address Map indicates that the starting address of USER:03 is 10 02 00 00H, and that the offset address of Performance Part 3 is 12 00H. Thus, the address is: 10 02 00 00H 12 00H 10 02 12 00H

+)

Since the size of the Performance Part is 00 00 00 19H, F0 (1) 41 (2) 10 (3) 6A (4) 11 (5) 10 02 12 00 address 00 00 00 19 size ?? checksum F7 (6)

(1) Exclusive status (4) Model ID (XP-30)

(2) ID number (Roland) (5) Command ID (RQ1)

(3) Device ID (17) (6) EOX

Next we calculate the checksum. 10H + 02H + 12H + 00H + 00H + 00H + 00H + 19H = 16 + 2 + 18 + 0 + 0 + 0 + 0 + 25 = 61 (sum) 61 (total) / 128 = 0 (product) ... 61 (remainder) checksum = 128 - 61 (remainder) = 67 = 43H Thus, a message of F0 41 10 6A 11 10 02 12 00 00 00 00 19 43 F7 would be transmitted.

Thus, the size of the retrieved data will be: 02 0F 17 01H -) 01 00 00 00H 01 0F 17 01H F0 (1) 41 (2) 10 (3) 6A (4) 11 (5) 01 00 00 00 address 01 0F 17 01 size ?? checksum F7 (6)

(1) Exclusive status (4) Model ID (XP-30)

(2) ID number (Roland) (5) Command ID (RQ1)

(3) Device ID (17) (6) EOX

Calculating the checksum as shown in <Example 2>, we get a message of F0 41 10 6A 11 01 00 00 00 01 0F 17 01 57 F7 to be transmitted.

204

MIDI Implementation

s Scale Tune Function (Model ID : 42H (GS), address: 40 1x 40H)


Scale Tune is a function that makes fine adjustments to the pitch of each note C-B. Settings are made for one octave, and applied to the notes of all octaves. By making Scale Tune settings you can use tunings and temperaments other than the standard Equal Temperament. Here we give three types of settings as examples. * Scale tune messages for any parts are recognized in the patch mode.

s ASCII Code Table


On the XP-30, the following ASCII code set is used for processing data such as the Patch Name and the Performance Name. ++++++++++++ | D | H | Char || D | H | Char || D | H | Char | ++++++++++++ | 32 | 20H | SP || 64 | 40H | @ || 96 | 60H | ` | | 33 | 21H | ! || 65 | 41H | A || 97 | 61H | a | | 34 | 22H | " || 66 | 42H | B || 98 | 62H | b | | 35 | 23H | # || 67 | 43H | C || 99 | 63H | c | | 36 | 24H | $ || 68 | 44H | D || 100 | 64H | d | | 37 | 25H | % || 69 | 45H | E || 101 | 65H | e | | 38 | 26H | & || 70 | 46H | F || 102 | 66H | f | | 39 | 27H | ` || 71 | 47H | G || 103 | 67H | g | | 40 | 28H | ( || 72 | 48H | H || 104 | 68H | h | | 41 | 29H | ) || 73 | 49H | I || 105 | 69H | i | | 42 | 2AH | * || 74 | 4AH | J || 106 | 6AH | j | | 43 | 2BH | + || 75 | 4BH | K || 107 | 6BH | k | | 44 | 2CH | , || 76 | 4CH | L || 108 | 6CH | l | | 45 | 2DH | - || 77 | 4DH | M || 109 | 6DH | m | | 46 | 2EH | . || 78 | 4EH | N || 110 | 6EH | n | | 47 | 2FH | / || 79 | 4FH | O || 111 | 6FH | o | | 48 | 30H | 0 || 80 | 50H | P || 112 | 70H | p | | 49 | 31H | 1 || 81 | 51H | Q || 113 | 71H | q | | 50 | 32H | 2 || 82 | 52H | R || 114 | 72H | r | | 51 | 33H | 3 || 83 | 53H | S || 115 | 73H | s | | 52 | 34H | 4 || 84 | 54H | T || 116 | 74H | t | | 53 | 35H | 5 || 85 | 55H | U || 117 | 75H | u | | 54 | 36H | 6 || 86 | 56H | V || 118 | 76H | v | | 55 | 37H | 7 || 87 | 57H | W || 119 | 77H | w | | 56 | 38H | 8 || 88 | 58H | X || 120 | 78H | x | | 57 | 39H | 9 || 89 | 59H | Y || 121 | 79H | y | | 58 | 3AH | : || 90 | 5AH | Z || 122 | 7AH | z | | 59 | 3BH | ; || 91 | 5BH | [ || 123 | 7BH | { | | 60 | 3CH | < || 92 | 5CH | \ || 124 | 7CH | | | | 61 | 3DH | = || 93 | 5DH | ] || 125 | 7DH | } | | 62 | 3EH | > || 94 | 5EH | ^ |++++ | 63 | 3FH | ? || 95 | 5FH | _ | ++++++++ D: decimal H: hexadecimal Note: SP indicates space.

Equal Temperament
This temperament divides the octave into 12 equal steps, and is the temperament most frequently used today, especially in western music. Initially, the Scale Tune function of this instrument is set to Equal Temperament.

Just Intonation (tonic of C)


The primary triads sound more beautiful in just intonation than in equal temperament. However, this applies only in one key, and chords will be discordant if you play in a different key. The settings here are for a tonic of C.

Arabian-type Scale
The Scale Tune function allow you to use various tunings of ethnic music. Here is one of the Arabian scales. Setting Examples Note C C# D Eb E F F# G G# A Bb B Equal Temp. 0 0 0 0 0 0 0 0 0 0 0 0 Just (in C) 0 -8 +4 +16 -14 -2 -10 +2 +14 -16 +14 -12 Arabian-type Scale -6 +45 -2 -12 -51 -8 +43 -4 +47 0 -10 -49

The values in the above table are in units of 1 cent. Convert these values to hexadecimal, and transmit them as exclusive data. For example to set the Scale Tune of Part 1 to an Arabian-type scale, transmit the following data. F0 41 10 42 12 40 11 40 3A 6D 3E 34 0D 38 6B 3C 6F 40 36 0F 76 F7

205

Appendices

64 Voice Expandable Synthesizer Model XP-30


Function...

Date : Jan. 18, 1999 Version : 1.00


Remarks

MIDI Implementation Chart


Transmitted X X X X
**************

Recognized 116 116 Mode 3 Mode 3, 4 (M = 1)

Basic Channel

Default Changed Default Messages Altered

Mode

*2

Note Number : True Voice Velocity After Touch Pitch Bend


0, 32 1 2 4 5 6, 38 7 8 10 11 64 65 66 67 69 71 72 73 74 80 81 82 83 84 91 93 15, 731, 6495 *3 15, 731, 6495 *3 98, 99 100, 101

0
**************

0127 0127 O O O O O
*1 O O O O O O O O O O O O O O O O (Resonance) O (Decay Time) O (Attack Time) O (Cutoff) O (Tone 1 Level) O (Tone 2 Level) O (Tone 3 Level) O (Tone 4 Level) O O (Reverb) O (Chorus) O O X O *1 *1 *1 *1 *1 *1 *1 *1 *1 *1 *1 *1 *1 *1 *1 *1 *1 *1 *1 *1 *1 *1 *1 *1 *1 *1 *1 *1 *1

Note On Note Off Key's Channel's

O O X O O
O O O O O O O O O O O O O O O O O O O O O O O O O O O O X O

*1 *1 *1
Bank select Modulation Breath type Foot type Portamento time Data entry Volume Balance Panpot Expression Hold 1 Portamento Sostenuto Soft Hold 2 Sound Controller 2 Sound Controller 3 Sound Controller 4 Sound Controller 5 General Purpose Controller 5 General Purpose Controller 6 General Purpose Controller 7 General Purpose Controller 8 Portamento control General purpose effects 1 General purpose effects 3 CC1 (General purpose controller 1) CC2 (General purpose controller 2) NRPN LSB, MSB RPN LSB, MSB

Control Change

Program Change

O : True Number
**************

*1

O 0127 O X X X O X O (120, 126, 127) O X O (123127) O X

*1 Program No. 1128 *1

System Exclusive : Song Position System : Song Select Common : Tune Request : Clock System Real Time : Commands

O X X X X X

*1

X : All Sound Off : Reset All Controllers X Aux X : Local On/Off Messages : All Notes Off X O : Active Sensing X : System Reset Notes
Mode 1 : OMNI ON, POLY Mode 3 : OMNI OFF, POLY

*1

* 1 O X is selectable. * 2 Recognized as M=1 even if M1. * 3 Can be changed settings.


Mode 2 : OMNI ON, MONO Mode 4 : OMNI OFF, MONO O : Yes X : No

206

Specifications
XP-30: 64 Voice Expandable Synthesizer(Conforms to General MIDI System)

q Keyboard
61 keys (with velocity, channel aftertouch)

q Display
40 characters, 2 lines (backlit LCD)

q Number of Parts
16 (Part 10 is Rhythm Part)

q Connectors
Output Jacks (L (MONO), R) Headphones Jack MIDI Connectors (IN, OUT, THRU) Computer Connector (Mac, PC-1, PC-2, MIDI) Hold Pedal Jack Control Pedal Jack Memory Card Slot

q Maximum Polyphony
64 voices

q Effects
EFX: 40 sets Reverb: 1 set (8 types) Chorus: 1 set

q Power Supply
AC 117 V, AC 230 V, AC 240 V

q Preset Memory
Patches: 1406 (640 same as the JV-2080 + 766 from Session, Orchestral and Techno Collection) Performances: 64 Rhythm Sets: 26 (10 same as the JV-2080 + 16 from Session and Techno Collection")

q Power Consumption
10 W (AC 117 V), 10 W (AC 230 V), 10 W (AC 240 V)

q Dimensions
1011 (W) x 289 (D) x 88 (H) mm 39-13/16 (W) x 11-7/16 (D) x 3-1/2 (H) inches

q User Memory
Patches: 128 Performances: 32 Rhythm Sets: 2

q Weight
7.8 kg / 17 lbs 4 oz (except Power cord)

q Accessories
Owners Manual Power Cable (Not included with XP-30 designed for 117 V power supply) CD-ROM (SoundDiver JV/XP)

q Wave Expansion Boards (sold separately)


Max. 2 Boards (D, E) * Each Wave Expansion Board includes Patches / Rhythm Sets that make use of the waves on the board.

q Arpeggiator
43 Styles

q Options
Wave Expansion Boards: SR-JV80 series SmartMedia: S2M-5 (2M bytes), S4M-5 (4M bytes)

*In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice.

207

Computer Cable Wiring Diagrams


For Apple Macintosh (Sold separately: RSC-15APL)

mini DIN, 8-pin, male 6 78 mini DIN, 8-pin, male HSKo HSKi TXDGND RXDTXD+ GPi RXD+ 1 2 3 4 5 6 7 8 mini DIN, 8-pin, male 1 2 3 4 5 6 7 8 HSKo HSKi TXDGND RXDTXD+ GPi RXD+

mini DIN, 8-pin, male 6 7 8

3 4 5 1 2

3 4 5 1 2

For PC (9-pin) (Sold separately: RSC-15AT)

mini DIN, 8-pin, male 6 78 mini DIN, 8-pin, male HSKo HSKi TXDGND RXD1 2 3 4 5 D-sub, 9-pin, female 7 RTS 8 CTS 3 TXD 5 GND 2 RXD D-sub, 9-pin, female 5 1

3 4 5 1 2

For PC (25-pin)

mini DIN, 8-pin, male 6 78 mini DIN, 8-pin, male HSKo HSKi TXDGND RXD1 2 3 4 5 D-sub, 25-pin, female 4 RTS 5 CTS 2 TXD 7 GND 3 RXD D-sub, 25-pin, female 13 1

3 4 5 1 2

25

14

208

Index
Symbols
[+OCT] .......................................................................12, 59 [-OCT] ........................................................................12, 59

C
C1/C2/C3/C4 slider assign .......................................111 C1/C2/C3/C4 slider output ......................................111 C1C4 slider ....................................................................34 Card ................................................................................115 [CATEGORY] ......................................................13, 32, 48 Category ...............................................................32, 4849 Category group ...............................................................32 Category select mode ...................................................108 Chorus ..............................................................................61 Chorus depth ..............................................72, 85, 89, 126 Chorus feedback level ................................72, 85, 89, 126 Chorus level ................................................72, 85, 89, 126 Chorus output assign .................................72, 85, 89, 126 Chorus pre delay ........................................72, 85, 89, 126 Chorus rate ..................................................72, 85, 89, 126 Chorus send level .................................7172, 84, 88, 125 CHORUS/DELAY .......................................................107 CHORUS/FLANGER ..................................................107 CHORUSDELAY ......................................................106 CHORUSFLANGER ................................................107 Clock source ..................................................................108 Coarse tune ..................................................79, 87, 91, 127 Compare function .................................................116, 118 COMPRESSOR ...............................................................96 Computer .......................................................................134 Computer cable .....................................................134, 208 COMPUTER connector ..........................................14, 135 COMPUTER switch .......................................14, 134135 Connection ..............................................................24, 134 Control 1 peak/hold ......................................................75 Control 2 peak/hold ......................................................75 Control 3 peak/hold ......................................................75 CONTROL PEDAL jack ................................................14 Control source 2 ..............................................................75 Control source 3 ..............................................................75 [CONTROLLER] .......................................................12, 34 Controller .........................................................................40 Copy ...............................................................................115 Copying .................................................................117, 128 Current part .....................................................................53 Cursor ..............................................................................45 Cursor button ............................................................13, 44 Cutoff frequency .......................................................80, 91 Cutoff frequency key follow .........................................80

Numerics
[18/916] ........................................................................13 2VOICE-PITCH-SHIFTER ..........................................102

A
AC inlet ............................................................................14 AC power cable ..............................................................25 Accent rate .....................................................................109 Aftertouch .......................................................................34 Aftertouch control source ...........................................111 Aftertouch information .........................................87, 127 Aftertouch sens .............................................................110 Alternate pan depth .................................................82, 92 Analog feel depth ...........................................................69 Arabian scale .................................................................114 ARP SELECT display ...............................................37, 56 Arpeggiator ...............................................................36, 56 [ARPEGGIO] .......................................................12, 36, 56 Arpeggio ..................................................................36, 108 arpeggio ...........................................................................56 ARPEGGIO display .......................................................59 Arpeggio part ................................................................110 Arpeggio style ...............................................................182 Audio cable .....................................................................25 AUTO-WAH ...................................................................95

B
Back select transmit switch .........................................113 Bank select group number ..........................................113 Bank select LSB .............................................................113 Bank select MSB ............................................................113 Battery check .................................................................114 Beat pattern ...................................................................109 Bend range ................................................................73, 90 Bender information ........................................................87 Bias direction ..................................................................82 Bias level ..........................................................................82 Bias point .........................................................................82 Booster gain .....................................................................71 Breath information .................................................87, 127 Bulk dump .....................................................................119

209

Index

D
Data transfer .................................................................115 Data type .......................................................................120 [DEC] ..........................................................................13, 45 Delay feedback level ..................................73, 86, 90, 126 [DEMO] ...........................................................................13 Demo play .......................................................................28 DEMO PLAY display ....................................................28 Demo song ......................................................................28 Depth 14 .........................................................................75 Desktop music ..............................................................134 Destination ............................................................120121 Destination 14 ...............................................................75 [DIGIT HOLD] ................................................................13 Digit hold .........................................................................48 DISTORTION ..................................................................93 DISTORTIONCHORUS ..........................................104 DISTORTIONDELAY ..............................................105 DISTORTIONFLANGER ........................................105

F
Factory default settings ...............................................123 Factory reset ....................................................27, 115, 123 FACTORY RESET display ............................................27 FBK-PITCH-SHIFTER ..................................................102 Filter type ...................................................................80, 91 [FILTER/ENV] .............................................12, 36, 51, 54 Fine tune ......................................................79, 87, 91, 127 FLANGER/DELAY .....................................................107 FLANGERDELAY ....................................................106 Foot information .....................................................87, 127 Format ............................................................................122 Front panel ......................................................................12 Function button ........................................................13, 43 FXM color ........................................................................76 FXM depth .......................................................................76 FXM switch ......................................................................76

G
GATE-REVERB .............................................................103 General MIDI system .....................................................11 [GM] .................................................................................12 GM initialize ..................................................................128 GM mode .................................................................43, 124 GM mode parameter ....................................................153 GM patch number ........................................................127 GM PLAY display ........................................................124 GM score data ...............................................................124 GM sound module .......................................................124 GM system on message ...............................................124

E
[EDIT] ...............................................................................13 Effects ...............................................................................61 [EFFECTS ON/OFF] ................................................12, 62 EFFECTS ON/OFF display ..........................................62 EFX control depth 1, 2 .......................................72, 85, 89 EFX control peak/hold ..................................................75 EFX control source 1, 2 ......................................72, 85, 89 EFX output level .........................................72, 84, 88, 125 EFX parameter ........................................................93, 154 EFX source .................................................................84, 88 EFX type ..............................................................71, 84, 88 ENHANCER ...................................................................94 ENHANCERCHORUS ............................................105 ENHANCERDELAY ...............................................106 ENHANCERFLANGER ..........................................105 [ENTER] ...........................................................................13 Envelope mode ...............................................................90 Equal temperament ......................................................114 Error message ...............................................................142 Exclusive device ID number .......................................113 Exclusive protect ..........................................................121 [EXIT] ...............................................................................13 [EXP A] ......................................................................13, 31 [EXP B] .......................................................................13, 31 [EXP C] .......................................................................13, 31 [EXP D] ......................................................................13, 31 [EXP E] .......................................................................13, 31 Expression information .........................................87, 127 Expression pedal ......................................................25, 35 External MIDI device ...........................................131132

H
Headphones ....................................................................25 HEXA-CHORUS .............................................................96 Hold 1 information .................................................87, 127 Hold control source ......................................................111 Hold pedal .................................................................35, 58 HOLD PEDAL jack ........................................................14

I
[INC] ...........................................................................13, 45 Initial data ......................................................................119 Initialize .........................................................................115 Initialize mode ..............................................................119 Initializing .............................................................119, 128 Internal write protect .....................................68, 116, 121

210

Index

K
Key assign mode ............................................................73 KEY EFFECTS section ....................................................12 Key mode .........................................................................83 Key range lower .......................................................70, 83 Key range switch ............................................................83 Key range upper .......................................................70, 83 Key scale ........................................................................114 Key shift .........................................................................113 Key switch .......................................................................90 Key velocity ...................................................................109 Keyboard sensitivity ....................................................110 Keyboard velocity ........................................................110

N
Name ................................................................................46 Number of simultaneous voices ..................................42 Numeric Key .............................................................13, 45

O
Octave range .................................................................109 Octave shift ..........................................................59, 69, 83 One-shot ...........................................................................64 Operating environment ...............................................108 Orchestral ..................................................................31, 47 Output assign/Output level .....................71, 84, 88, 125 OUTPUT jacks (L (MONO), R) .....................................14 OVERDRIVE ...................................................................93 OVERDRIVEDELAY ...............................................104 OVERDRIVEFLANGER ..........................................104

L
Layer ................................................................................52 Layer performance .........................................................51 LCD contrast .................................................................108 [LEVEL] .........................................................12, 36, 51, 54 Level ...............................................................68, 81, 87, 92 LFO ...................................................................................78 LFO delay time ...............................................................79 LFO external sync ...........................................................78 LFO fade mode ...............................................................78 LFO fade time .................................................................79 LFO form .........................................................................78 LFO key sync ..................................................................78 LFO offset ........................................................................79 LFO rate ...........................................................................78 LIMITER ..........................................................................96 Load ................................................................................115 Local OFF ......................................................................137 Local switch ............................................................86, 112 Looped .............................................................................64

P
Page button .....................................................................13 Palette display ...........................................................63, 65 [PALETTE EDIT] ................................................13, 63, 65 PALETTE section ............................................................12 Pan ..........................................................69, 81, 87, 92, 127 Pan information ......................................................87, 127 Pan key follow ................................................................82 Pan LFO depth 1, 2 .........................................................79 [PANIC] ...........................................................................13 Panic .................................................................................60 Parameter .......................................................................147 [PART] .............................................................................12 Part ...................................................................................41 Part button .......................................................................43 [PATCH] ..............................................................12, 30, 47 Patch .............................................................30, 41, 47, 168 Patch category .................................................................68 Patch clock source ..........................................................68 Patch copy .....................................................................117 Patch effects copy .........................................................117 Patch group .....................................................................87 Patch initialize ...............................................................119 Patch mode ................................................................42, 47 Patch mode receive channel ........................................112 Patch mode transmit channel .....................................112 Patch name ......................................................................68 Patch name copy ...........................................................118 Patch number ..................................................................87 Patch parameter ......................................................68, 147 PATCH PLAY display .............................................30, 47 Patch remain switch .....................................................108 Patch scale .....................................................................114 Patch search function ...............................................32, 48 Patch tempo .....................................................................68 Patch tone copy .............................................................117 Patch write .....................................................................116 Peak control source ......................................................111 Pedal assign ...................................................................110 Pedal output ..................................................................110 Pedal polarity ........................................................110111

M
Master tune ...................................................................113 Memory ...................................................................67, 115 Memory card ...................................................67, 115, 121 MEMORY CARD slot ....................................................14 MIDI ...............................................................................112 MIDI cable .......................................................................25 MIDI channel ..................................................................86 MIDI connectors (IN, OUT, THRU) ............................14 MIDI information .........................................................127 MIDI interface ...............................................................135 MODE section .................................................................12 Modulation ......................................................................34 Modulation information ........................................87, 127 MODULATION-DELAY ...............................................99 Motif ...............................................................................109 Multi-effects ..............................................................61, 93 Multitimbral sound source .....................................41, 53 Mute group .....................................................................90

211

Index

Pedal switch ............................................................25, 131 [PERFORM] ...............................................................12, 51 PERFORM NAME ..........................................................83 PERFORM PLAY display ..............................................51 Performance ......................................................41, 51, 181 Performance clock source .............................................83 Performance control channel ......................................112 Performance copy ........................................................117 Performance effects copy ............................................117 Performance initialize ..................................................119 Performance mode ...................................................42, 51 Performance name .........................................................83 Performance name copy ..............................................117 Performance parameter .........................................83, 150 Performance part copy ................................................117 Performance tempo ........................................................83 Performance write ........................................................116 PHASER ...........................................................................94 PHONES jack ..................................................................14 [PHRASE PREVIEW] .........................................12, 33, 49 Phrase preview .................................................33, 49, 113 Pitch bend ........................................................................34 Pitch bend information ................................................127 Pitch bend/Modulation lever .................................13, 34 Pitch envelope depth ...............................................79, 91 Pitch envelope level 14 ..........................................80, 91 Pitch envelope time 1 velocity sensitivity ..................80 Pitch envelope time 14 ...........................................80, 91 Pitch envelope time 4 velocity sensitivity ..................80 Pitch envelope time key follow ....................................80 Pitch envelope time velocity sensitivity .....................91 Pitch envelope velocity sensitivity ........................80, 91 Pitch key follow ..............................................................79 Pitch LFO depth 1, 2 ......................................................79 [PORTAMENTO] ...............................................12, 35, 50 Portamento ................................................................35, 50 Portamento mode ...........................................................73 Portamento start pitch ...................................................74 Portamento switch .........................................................73 Portamento time .............................................................73 Portamento type .............................................................73 Power switch .............................................................14, 26 Power up mode ............................................................108 Preset memory ................................................................67 Preview note set 14 ....................................................113 PREVIEW SELECT display ...........................................49 Preview sound mode .............................................49, 113 Preview velocity ...........................................................113 Program change ............................................................114 Pure temperament ........................................................114

R
Random pan depth ..................................................82, 92 Random pitch depth ................................................79, 91 Rear panel ........................................................................14 Receive bank select switch ..........................................112 Receive exclusive switch .............................................113 Receive GM exclusive switch .....................................113 Receive hold 1 switch ........................................74, 86, 90 Receive pan control switch .....................................74, 90 Receive pitch bend switch .............................................74 Receive program change switch ..........................86, 112 Receive switch ...........................................................86, 90 Receive volume switch ......................................74, 86, 90 Redamper switch ............................................................74 Remote keyboard switch .............................................112 Resonance ..................................................................80, 91 Resonance velocity sensitivity ................................81, 92 REVERB .........................................................................103 Reverb ..............................................................................61 Reverb send level .........................7172, 84, 88, 125126 Reverb/Delay HF damp ...........................73, 86, 90, 126 Reverb/Delay level ....................................73, 86, 90, 126 Reverb/Delay time ....................................73, 85, 89, 126 Reverb/Delay type .....................................73, 85, 89, 126 [RHYTHM] ..........................................................12, 38, 55 Rhythm key copy .........................................................118 RHYTHM PLAY display .........................................38, 55 Rhythm set ..................................................38, 41, 55, 177 Rhythm set copy ...........................................................118 Rhythm set initialize ....................................................119 Rhythm set mode .....................................................42, 55 Rhythm set name ............................................................88 Rhythm set name copy ................................................118 Rhythm set parameter ...........................................88, 151 Rhythm set write ..........................................................116 Ring modulator ...............................................................71 ROTARY ..........................................................................95

Q
QUADRUPLE-TAP-DELAY .......................................101

212

Index

S
Save ................................................................................115 Scale tune switch ..........................................................113 Session ..................................................................31, 47, 55 [SHIFT] .............................................................................13 Shuffle rate ....................................................................109 Single performance ........................................................51 Slots EXP-D and E ..................................................16, 114 SmartMedia .....................................................................67 [SOLO] .................................................................12, 35, 50 Solo .............................................................................35, 50 Solo legato switch ...........................................................73 Sound palette ..................................................................36 Sound palette function ............................................50, 54 Sound source .............................................................40, 42 Source block ..........................................................120121 SPACE-D .........................................................................97 SPECTRUM .....................................................................94 Split ..................................................................................52 SR-JV80 series ...........................................................16, 67 STEP-FLANGER .............................................................98 STEREO-CHORUS .........................................................97 STEREO-DELAY ............................................................99 STEREO-EQ ....................................................................93 STEREO-FLANGER .......................................................98 Storing ............................................................................116 Stretch tuning depth ......................................................69 Stretched tuning .............................................................69 Structure ..........................................................................70 Structure type .................................................................70 Style ................................................................................108 [SYSTEM] ........................................................................12 System control assign 1/2 ...........................................111 System controller 1 information ...................................87 System controller 2 information ...................................87 System memory ..............................................................67 System mode ...................................................................43 System parameter .................................................108, 158 System tempo ................................................................108

T
Techno ..............................................................................47 Techno Collection ...............................................31, 47, 55 Tempo ............................................................................110 Temporary area ..............................................................67 Thru function ................................................................137 TIME-CONTROL-DELAY ..........................................101 Tone ............................................................................40, 50 Tone delay mode ............................................................76 Tone delay time ..............................................................77 [TONE SELECT] .............................................................44 Tone select button ..........................................................44 [TONE SWITCH] ............................................................44 Tone switch .....................................................................76 Tone switch button .........................................................44 Transmit active sensing switch ..................................113 Transmit bank select group ..........................................86 Transmit bank select LSB ............................................114 Transmit bank select MSB ...........................................114 Transmit bank select switch ........................................112 Transmit edit data switch ............................................113 Transmit MIDI channel ...............................................114 Transmit program change ...........................................114 Transmit program change switch ..............................112 Transmit switch ..............................................................86 Transmit volume ............................................................87 Transmitting ..........................................................119, 128 [TRANSPOSE] ..........................................................12, 60 Transpose .........................................................................60 Transpose switch/value ..............................................110 TREMOLO-CHORUS ....................................................97 TRIPLE-TAP-DELAY ...................................................100 Tuning ............................................................................113 TVA ............................................................................81, 92 TVA envelope 13 ..........................................................82 TVA envelope 14 ..........................................................82 TVA envelope level 13 .................................................92 TVA envelope time 14 .................................................92 TVA envelope time 4 velocity sensitivity ...................82 TVA envelope time key follow .....................................82 TVA envelope time velocity sensitivity ......................92 TVA envelope velocity curve .......................................81 TVA envelope velocity sensitivity .........................81, 92 TVA LFO depth 1, 2 .......................................................79 TVF .............................................................................80, 91 TVF envelope depth .................................................80, 91 TVF envelope level 14 ............................................81, 92 TVF envelope time 1 velocity sensitivity ..............8182 TVF envelope time 14 ............................................81, 92 TVF envelope time 4 velocity sensitivity ....................81 TVF envelope time key follow .....................................81 TVF envelope time velocity sensitivity .......................92 TVF envelope velocity curve ........................................81 TVF envelope velocity sensitivity ..........................81, 92 TVF LFO depth 1, 2 ........................................................79

213

Index

U
Undo .................................................................................45 [UNDO/COMPARE] ..............................13, 45, 116, 118 User memory ....................................................6768, 116 User memory protect ...................................................115 UTIL 1 display ..........................................................27, 68 UTIL 2 display ................................................................27 [UTIL/CARD] ............................................12, 27, 68, 115 Utility/Card mode .................................................43, 115

V
VALUE dial ...............................................................13, 45 Velocity ............................................................................34 Velocity cross fade .........................................................69 Velocity range lower ......................................................69 Velocity range switch ....................................................69 Velocity range upper .....................................................69 Voice information ...................................................87, 127 Voice priority ..................................................................69 Voice reserve .............................................................42, 87 Volume ...........................................................................127 Volume control source ................................................111 Volume information ..............................................87, 127 VOLUME slider ..............................................................26 Volume slider ..................................................................12

W
Wave ................................................................................47 Wave expansion board ........................16, 47, 55, 67, 114 WAVE EXPANSION section ........................................13 Wave gain ..................................................................76, 90 Wave group ...............................................................76, 90 Wave number ...........................................................76, 90 Waveform ......................................................................160 Write ...............................................................................115 WRITE display ................................................................68

214

For EU Countries

CAUTION

Apparatus containing Lithium batteries

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturers instructions.

ADVARSEL!
Lithiumbatteri - Eksplosionsfare ved fejlagtig hndtering. Udskiftning m kun ske med batteri af samme fabrikat og type. Levr det brugte batteri tilbage til leverandren.

VARNING
Explosionsfara vid felaktigt batteribyte. Anvnd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera anvnt batteri enligt fabrikantens instruktion.

ADVARSEL
Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme batteritype eller en tilsvarende type anbefalt av apparatfabrikanten. Brukte batterier kasseres i henhold til fabrikantens instruks joner.

VAROITUS
Paristo voi rjht, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hvit kytetty paristo valmistajan ohjeiden mukaisesti.

For EU Countries This product complies with the requirements of European Directives EMC 89/336/EEC and LVD 73/23/EEC. For the USA

FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT


This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Unauthorized changes or modification to this system can void the users authority to operate this equipment. This equipment requires shielded interface cables in order to meet FCC class B Limit. For Canada

NOTICE
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

AVIS
Cet appareil numrique de la classe B respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada.

When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below.

Information

AFRICA
EGYPT
Al Fanny Trading Office
9, EBN Hagar A1 Askalany Street, ARD E1 Golf, Heliopolis, Cairo 11341, EGYPT TEL: 20-2-417-1828

SINGAPORE
Swee Lee Company
150 Sims Drive, SINGAPORE 387381 TEL: 6846-3676

PANAMA
SUPRO MUNDIAL, S.A.
Boulevard Andrews, Albrook, Panama City, REP. DE PANAMA TEL: 315-0101

ITALY
Roland Italy S. p. A.
Viale delle Industrie 8, 20020 Arese, Milano, ITALY TEL: (02) 937-78300

ISRAEL
Halilit P. Greenspoon & Sons Ltd.
8 Retzif Ha'aliya Hashnya St. Tel-Aviv-Yafo ISRAEL TEL: (03) 6823666

CRISTOFORI MUSIC PTE LTD


Blk 3014, Bedok Industrial Park E, #02-2148, SINGAPORE 489980 TEL: 6243-9555

PARAGUAY
Distribuidora De Instrumentos Musicales
J.E. Olear y ESQ. Manduvira Asuncion PARAGUAY TEL: (021) 492-124

NORWAY
Roland Scandinavia Avd. Kontor Norge
Lilleakerveien 2 Postboks 95 Lilleaker N-0216 Oslo NORWAY TEL: 2273 0074

JORDAN
AMMAN Trading Agency
245 Prince Mohammad St., Amman 1118, JORDAN TEL: (06) 464-1200

REUNION
Maison FO - YAM Marcel
25 Rue Jules Hermann, Chaudron - BP79 97 491 Ste Clotilde Cedex, REUNION ISLAND TEL: (0262) 218-429

TAIWAN
ROLAND TAIWAN ENTERPRISE CO., LTD.
Room 5, 9fl. No. 112 Chung Shan N.Road Sec.2, Taipei, TAIWAN, R.O.C. TEL: (02) 2561 3339

URUGUAY
Todo Musica S.A.
Francisco Acuna de Figueroa 1771 C.P.: 11.800 Montevideo, URUGUAY TEL: (02) 924-2335

POLAND
P. P. H. Brzostowicz
UL. Gibraltarska 4. PL-03664 Warszawa POLAND TEL: (022) 679 44 19

KUWAIT
Easa Husain Al Yousifi Est.
Abdullah Salem Street, Safat, KUWAIT TEL: 243-6399

SOUTH AFRICA
That Other Music Shop (PTY) Ltd.
11 Melle St., Braamfontein, Johannesbourg, SOUTH AFRICA P.O.Box 32918, Braamfontein 2017 Johannesbourg, SOUTH AFRICA TEL: (011) 403 4105

THAILAND
Theera Music Co. , Ltd.
330 Verng NakornKasem, Soi 2, Bangkok 10100, THAILAND TEL: (02) 2248821

VENEZUELA
Musicland Digital C.A.
Av. Francisco de Miranda, Centro Parque de Cristal, Nivel C2 Local 20 Caracas VENEZUELA TEL: (212) 285-8586

PORTUGAL
Tecnologias Musica e Audio, Roland Portugal, S.A.
Cais Das Pedras, 8/9-1 Dto 4050-465 PORTO PORTUGAL TEL: (022) 608 00 60

LEBANON
Chahine S.A.L.
Gerge Zeidan St., Chahine Bldg., Achrafieh, P.O.Box: 16-5857 Beirut, LEBANON TEL: (01) 20-1441

VIETNAM
Saigon Music
138 Tran Quang Khai St., District 1 Ho Chi Minh City VIETNAM TEL: (08) 844-4068

QATAR
Al Emadi Co. (Badie Studio & Stores)
P.O. Box 62, Doha, QATAR TEL: 4423-554

Paul Bothner (PTY) Ltd.


17 Werdmuller Centre, Main Road, Claremont 7708 SOUTH AFRICA P.O.BOX 23032, Claremont 7735, SOUTH AFRICA TEL: (021) 674 4030

ROMANIA
FBS LINES
Piata Libertatii 1, RO-4200 Gheorghehi TEL: (095) 169-5043

EUROPE
AUSTRIA
Roland Austria GES.M.B.H.
Siemensstrasse 4, P.O. Box 74, A-6063 RUM, AUSTRIA TEL: (0512) 26 44 260

ASIA
CHINA
Roland Shanghai Electronics Co.,Ltd.
5F. No.1500 Pingliang Road Shanghai, CHINA TEL: (021) 5580-0800

AUSTRALIA/ NEW ZEALAND


AUSTRALIA
Roland Corporation Australia Pty., Ltd.
38 Campbell Avenue Dee Why West. NSW 2099 AUSTRALIA TEL: (02) 9982 8266

RUSSIA
MuTek
3-Bogatyrskaya Str. 1.k.l 107 564 Moscow, RUSSIA TEL: (095) 169 5043

SAUDI ARABIA
aDawliah Universal Electronics APL
Corniche Road, Aldossary Bldg., 1st Floor, Alkhobar, SAUDI ARABIA P.O.Box 2154, Alkhobar 31952 SAUDI ARABIA TEL: (03) 898 2081

BELGIUM/HOLLAND/ LUXEMBOURG Roland Benelux N. V.


Houtstraat 3, B-2260, Oevel (Westerlo) BELGIUM TEL: (014) 575811

SPAIN
Roland Electronics de Espaa, S. A.
Calle Bolivia 239, 08020 Barcelona, SPAIN TEL: (93) 308 1000

SYRIA
Technical Light & Sound Center
Khaled Ebn Al Walid St. Bldg. No. 47, P.O.BOX 13520, Damascus, SYRIA TEL: (011) 223-5384

Roland Shanghai Electronics Co.,Ltd. (BEIJING OFFICE)


10F. No.18 Anhuaxili Chaoyang District, Beijing, CHINA TEL: (010) 6426-5050

NEW ZEALAND
Roland Corporation Ltd.
32 Shaddock Street, Mount Eden, Auckland, NEW ZEALAND TEL: (09) 3098 715

DENMARK
Roland Scandinavia A/S
Nordhavnsvej 7, Postbox 880, DK-2100 Copenhagen DENMARK TEL: 3916 6200

SWEDEN
Roland Scandinavia A/S SWEDISH SALES OFFICE
Danvik Center 28, 2 tr. S-131 30 Nacka SWEDEN TEL: (0)8 702 00 20

TURKEY
Barkat muzik aletleri ithalat ve ihracat Ltd Sti
Siraselviler Caddesi Siraselviler Pasaji No:74/20 Taksim - Istanbul, TURKEY TEL: (0212) 2499324

HONG KONG
Tom Lee Music Co., Ltd. Service Division
22-32 Pun Shan Street, Tsuen Wan, New Territories, HONG KONG TEL: 2415 0911

CENTRAL/LATIN AMERICA
ARGENTINA
Instrumentos Musicales S.A.
Av.Santa Fe 2055 (1123) Buenos Aires ARGENTINA TEL: (011) 4508-2700

FRANCE
Roland France SA
4, Rue Paul Henri SPAAK, Parc de l'Esplanade, F 77 462 St. Thibault, Lagny Cedex FRANCE TEL: 01 600 73 500

SWITZERLAND
Roland (Switzerland) AG
Landstrasse 5, Postfach, CH-4452 Itingen, SWITZERLAND TEL: (061) 927-8383

FINLAND
Roland Scandinavia As, Filial Finland
Lauttasaarentie 54 B Fin-00201 Helsinki, FINLAND TEL: (0)9 68 24 020

UKRAINE
TIC-TAC
Mira Str. 19/108 P.O. Box 180 295400 Munkachevo, UKRAINE TEL: (03131) 414-40

U.A.E.
Zak Electronics & Musical Instruments Co. L.L.C.
Zabeel Road, Al Sherooq Bldg., No. 14, Grand Floor, Dubai, U.A.E. TEL: (04) 3360715

INDIA
Rivera Digitec (India) Pvt. Ltd.
409, Nirman Kendra Mahalaxmi Flats Compound Off. Dr. Edwin Moses Road, Mumbai-400011, INDIA TEL: (022) 2493 9051

BRAZIL
Roland Brasil Ltda
Rua San Jose, 780 Sala B Parque Industrial San Jose Cotia - Sao Paulo - SP, BRAZIL TEL: (011) 4615 5666

GERMANY
Roland Elektronische Musikinstrumente HmbH.
Oststrasse 96, 22844 Norderstedt, GERMANY TEL: (040) 52 60090

UNITED KINGDOM
Roland (U.K.) Ltd.
Atlantic Close, Swansea Enterprise Park, SWANSEA SA7 9FJ, UNITED KINGDOM TEL: (01792) 700139

NORTH AMERICA
CANADA
Roland Canada Music Ltd. (Head Office)
5480 Parkwood Way Richmond B. C., V6V 2M4 CANADA TEL: (604) 270 6626

INDONESIA
PT Citra IntiRama
J1. Cideng Timur No. 15J-150 Jakarta Pusat INDONESIA TEL: (021) 6324170

COSTA RICA
JUAN Bansbach Instrumentos Musicales
Ave.1. Calle 11, Apartado 10237, San Jose, COSTA RICA TEL: 258-0211

GREECE
STOLLAS S.A. Music Sound Light
155, New National Road Patras 26442, GREECE TEL: 2610 435400

KOREA
Cosmos Corporation
1461-9, Seocho-Dong, Seocho Ku, Seoul, KOREA TEL: (02) 3486-8855

MIDDLE EAST
BAHRAIN
Moon Stores
No.16, Bab Al Bahrain Avenue, P.O.Box 247, Manama 304, State of BAHRAIN TEL: 211 005

CHILE
Comercial Fancy S.A.
Rut.: 96.919.420-1 Nataniel Cox #739, 4th Floor Santiago - Centro, CHILE TEL: (02) 688-9540

Roland Canada Music Ltd. (Toronto Office)


170 Admiral Boulevard Mississauga On L5T 2N6 CANADA TEL: (905) 362 9707

HUNGARY
Roland East Europe Ltd.
Warehouse Area DEPO Pf.83 H-2046 Torokbalint, HUNGARY TEL: (23) 511011

MALAYSIA
BENTLEY MUSIC SDN BHD
140 & 142, Jalan Bukit Bintang 55100 Kuala Lumpur,MALAYSIA TEL: (03) 2144-3333

EL SALVADOR
OMNI MUSIC
75 Avenida Norte y Final Alameda Juan Pablo , Edificio No.4010 San Salvador, EL SALVADOR TEL: 262-0788

U. S. A.
Roland Corporation U.S.
5100 S. Eastern Avenue Los Angeles, CA 90040-2938, U. S. A. TEL: (323) 890 3700

IRELAND
Roland Ireland
Audio House, Belmont Court, Donnybrook, Dublin 4. Republic of IRELAND TEL: (01) 2603501

CYPRUS
Radex Sound Equipment Ltd.
17, Diagorou Street, Nicosia, CYPRUS TEL: (022) 66-9426

PHILIPPINES G.A. Yupangco & Co. Inc.


339 Gil J. Puyat Avenue Makati, Metro Manila 1200, PHILIPPINES TEL: (02) 899 9801

MEXICO
Casa Veerkamp, s.a. de c.v.
Av. Toluca No. 323, Col. Olivar de los Padres 01780 Mexico D.F. MEXICO TEL: (55) 5668-6699

IRAN
MOCO, INC.
No.41 Nike St., Dr.Shariyati Ave., Roberoye Cerahe Mirdamad Tehran, IRAN TEL: (021) 285-4169 As of December 1, 2002 (Roland)

01783690

03-2-A2-81N

You might also like