Professional Documents
Culture Documents
Page: The Bifurcated Fan Range - Introduction Applications Specification Forms of Running, Test Methods & Quality Systems Guide To Fan Selection Bifurcated Fan - Series 33 Motor Frame Size Schedules:80C Continuous 200C Contnuous Performance Curves Dimensions & Weights - Series 33 Dimensions & Weights - JM Ancillaries 3 4 5 6 7 8
9 10 SK10751-11597 25 26 27-28
Varofoil - variable pitch in motion fans Centrifugal Fans - industrial & commercial In Line Centrifugal Mixed Flow Fans Plate Mounted Fans
JM IMPELLER
COOLING FAN
Bifurcated fan eliminates this problem with its TYPICAL APPLICATIONS motor out of the airstream. Care must be Temperature Range Different sizes of fan are rated for different maxi- taken to maintain minimum velocities for the conveying of dusts in the air stream. (If the mum temperature as in the table below:dust causes a change from standard air denMaximum Temperature sity (1.2 kg/m3) please refer to your nearest sales office). 80C 200C 320C* Flammable Gases 150 - 300 mm X X With the additional fitting of a spark minimising 400 - 1000 mm X X impeller track, the fans are suitable for Group 2A and 2B gases. The fan must be mounted *Special - made to order only outside of the hazardous area. The shaft seal Mists and Condensation must be correctly maintained. The Bifurcated fan is capable of handling mists up Corrosive Chemicals to 100 % relative humidity. When there is a danger The Bifurcated fan is suitable for some mild of vapour condensing out in the fan duct 150 mm chemicals that will not corrode the galvanised to 500mm diameter fans should not be mounted casing or the seal of the motor shaft through horizontally due to their case design. All ducts the case. Additional protection can be providshould be laid to a slight fall to facilitate drainage. ed by an epoxy paint finish. Dusts Please refer corrosive chemicals such as Where there is a danger of dusts building up acids and solvents to ourselves where we can around the motor of a standard axial fan the advise on the suitability of the fan.
4
ensure quality. Balanced to BS6861 Part 1 1987 (ISO 19401986) Grade G6.3. Ancillaries Guards to comply with BS848 Pt 5. and draft ISO standards. 2 speed switch for Delta/Star reconnection Silencers Mounting feet for both horizontal and vertical mounting Matching Flanges. Flexible Connectors. Air Operated Dampers.** Bellmouth inlets. ** Vibration Isolators. Finish Standard: The fan casing, mounting feet, matching flanges and guards are all hot dipped galvanised after manufacture, (in accordance with BS729:1971). Motors, aluminium self finish, or painted to motor manufacturers specification. Non Standard: For more corrosive conditions the fans can be treated at extra cost with an epoxy paint finish. The maximum temperature for this finish is +120C (continuous). Additional Extra Features Epoxy Paint System Finish. Non Standard Voltages. Motor Thermistors. Motor Thermostats or Thermal Switches. Motor anti-condensation Heaters. Spark Minimising Feature. * Available 150 mm - 300 mm only ** Available 400 mm - 1000 mm only
JM AEROFOIL - BIFURCATED
FORMS OF RUNNING, TEST METHODS & QUALITY SYSTEMS
The direction of airflow through the fan and the mounting position are defined as the Form of Running. Woods only offer Form B running bifurcated fans as Form A fans have a marked loss in performance. For vertical operation add suffix U for airflow up, or suffix D for airflow down. Arrows indicating correct rotation and the direction of air flow are incorporated on the fan duct nameplate.
Single Stage
Form B
Form BU Form BD
Two Stage
Form B/B
For Two Stage selections, please refer your enquiry to a Woods representative.
Testing The air and sound performance data has been measured by the latest version of British and International Standards:ISO 5801 category D (fully ducted) method for testing air performance (supercedes BS848 Pt1 1980). BS848 Pt 2 1985, method of noise testing. It is essential, when comparing fan performances, that the same installation category and test standards are used at all times. Acoustic Data The sound levels quoted are based on tests carried out under the Woods certified laboratory conditions. Using the spectrum corrections stated on each performance chart, an unweighted sound power spectrum can be obtained for the fan. Motor Ratings The motor ratings, starting, full load currents and speeds refer to the maximum output of the motor. When the impeller does not require the full output, the power and current will be less than the maximum quoted.
6
Quality Systems Woods Air Movement are committed to Quality Assurance. Registered to BS EN ISO 9001.94, N.A.T.O. Quality Standard AQAP-1 Edn 3. BS EN ISO 9001.94 registration means that Woods design is quality assured as well as the manufacture. Our commitment to Quality Assurance doesn't stop with the hardware. The performance data comes from standard tests carried out in Woods own laboratory which is BSI (CAME) and AMCA accredited. A JM Aerofoil Bifurcated fan can be bought with the confidence, as with all Woods products, that it will achieve the published performance data and match the assured quality. All the Woods JM Aerofoils are fitted with IP55 motors as standard, and come with a 2 year guarantee.
PERFORMANCE
JM Aerofoil Bifurcated Fans - 40JM - 100JM
1000 800 600 400
63JM/20/4/6
50JM/20/4/6
Total Pressure Pa
200
40JM/20/4/6
50JM/16/4/5
100 80 60 40
40JM/16/4/5
20
10
.1
.2
.3
.4
.5
.6 .7 .8 .9 1
7 8
10 12 14 1618 20
Electrical Supply 220 V -240 V 50Hz 1 380 V - 420 V 50Hz 3 Casings All casings are hot dipped galvanised for long life and high resistance corrosion. A seal is provided on the motor shaft. Impellers Cast in aluminium silicon alloy and has a fixed pitch aerofoil blade. This ensures strength, reliability and performance at high temperature. Temperature Range Standard 200C, made to order 320C. Ancillary Equipment Silencers, Mounting Feet/Plates, Vibration Isolators, Matching Flanges, High Temperature Flexible Connectors.
Sound pressure levels quoted are average dB(A) at 3 m distance over a sphere, based on form B running under free field conditions, and are presented for comparative purposes only. Cylindrical silencers are available as standard. Bifurcated fans are not suitable for speed regulation.
ft3/min m3/hr 500 400 300 psF - Fan (S tatic) Pressure (Pa) 200 50
50 100
100 500
500 1000
10 8 6 5 4 3 2
10 0.01
0.02
0.03 0.04
0.06
0.1
0.2
(m3/s)
0.8 1
qv - Volume Flow
JM AEROFOIL - BIFURCATED
Motor Frame Size Schedules: 80C Continuous
400 V / 50 Hz / 3
Speed Code rev/min 40JM.BIF/16/4/5/... 1440 Angle () 38 40 36 40 18 26 32 38 40 14 22 30 38 12 20 28 32 8 12 16 18 24 30 30 32 12 16 28 32 10 20 24 10 12 20 22 18 24 30 DA71MAC DA71MAC DA71MAC DA71MAC F2225 F2225 F2225 F2225 F2225 DA71MAC DA71MAC DA80MAC DA80MAC DA71MAC DA71MAC DA80MAC DA80MAC F2225 F2225 F2225 F2225 F2229 F2229 F2265 F2265 DA80MAC F2245 F2245 F2245 F2265 F2265 F2269 F2245 F2245 F2249 F2249 DA132SAD DA132MAD DA132MBD Max. Pitch Motor Motor Rating (kW) 0.25 0.37 0.25 0.37 1 1.5 2 2.5 3.1 0.25 0.37 0.55 0.75 0.25 0.37 0.55 0.75 1.5 2 2.5 3.1 4.3 5.5 0.55 1 0.75 1 1.8 2.2 0.55 1 1.3 1.8 2.2 3.2 3.8 3 4 5.5 Full Load Current (A) 0.8 1.1 0.8 1.1 2.6 3.4 4.5 5.6 6.6 0.8 1.1 1.5 2 0.8 1.1 1.5 2 3.4 4.5 5.6 6.6 8.4 11.1 1.7 3 2 2.4 4.1 5 1.7 3 3.9 4.1 5 7 7.7 6.7 8.6 11.6 Starting Current d.o.l. (A) 3.5 4.9 3.5 4.9 15.2 22 30 38 44 3.5 4.9 6.7 9.9 3.5 4.9 6.7 9.9 22 30 38 44 75 90 7.6 12.5 9.9 14 24 30 7.6 12.5 13 24 30 45 45 44 57 80 Efficiency % 66 69 66 69 73 77 75 77 78 66 69 70 72 66 69 70 72 77 75 77 78 86 85 65 71 72 80 82 83 65 71 74 82 83 84 84 86 87 88 Power Factor cos 0.69 0.71 0.69 0.71 0.76 0.83 0.85 0.84 0.86 0.69 0.71 0.76 0.76 0.69 0.71 0.76 0.76 0.83 0.85 0.84 0.86 0.86 0.84 0.72 0.67 0.76 0.75 0.77 0.76 0.72 0.67 0.67 0.77 0.76 0.78 0.84 0.76 0.78 0.78
40JM.BIF/20/4/6/...
1440
40JM.BIF/20/2/6/...
2950
50JM.BIF/16/4/5/...
1440
50JM.BIF/20/4/6/...
1440
50JM.BIF/20/2/6/...
2950
63JM.BIF/20/6/6/...
935
63JM.BIF/20/4/6/...
1440
80JM.BIF/20/6/6/...
935
80JM.BIF/20/4/6/...
1440
100JM.BIF/25/6/9/...
960
100JM.BIF/25/4/9/...
1470
8 12 20 24
5.5 7.5 11 15
11 14.3 22.2 29
88 89 89 90
JM AEROFOIL - BIFURCATED
Motor Frame Size Schedules: 200C Continuous
400 V / 50 Hz / 3
Speed Code rev/min 40JM.BIF/20/4/6/... 40JM.BIF/20/2/6/... 1440 2950 Angle () 40 18 26 32 24 32 8 12 24 30 30 32 10 16 30 32 10 24 10 20 18 24 30 8 12 20 24 F2245 F2225 F2225 F2225 F2245 F2245C F2225 F2225 F2229 F2229 F2265 F2265 F2245C F2245 F2245 F2249 F2265 F2265 F2245 F2249 DA132SAD DA132MAD DA132MBD DA132SAD DA132MAD DA160MAD DA160LAD Max. Pitch Motor Motor Rating (kW) 0.5 1 1.5 2 0.5 0.75 1.5 2 4 5.5 0.55 1.2 0.75 1 2 3.5 0.55 1.2 2 3.5 3 4 5.5 5.5 7.5 11 15 Full Load Current (A) 1.4 2.6 3.4 4.5 1.4 1.7 3.4 4.5 7.8 11.1 1.7 3.6 1.7 2.4 4.5 7 1.7 3.6 4.5 7 6.7 8.6 11.6 11 14.3 22.2 29 Starting Current d.o.l. (A) 7 15.2 22 30 7 10 22 30 75 90 7.6 15 10 14 30 45 7.6 15 30 45 44 57 80 77 107 133 189 Efficiency % 71 73 77 76 71 83 77 76 86 85 65 70 83 80 83 84 65 70 83 84 86 87 88 88 89 89 90 Power Factor cos 0.72 0.76 0.83 0.85 0.72 0.77 0.83 0.85 0.86 0.84 0.72 0.6 0.77 0.73 0.76 0.84 0.72 0.6 0.76 0.84 0.76 0.78 0.78 0.83 0.85 0.81 0.83
50JM.BIF/20/4/6/...
1440
50JM.BIF/20/2/6/...
2950
63JM.BIF/20/6/6/...
935
63JM.BIF/20/4/6/...
1440
80JM.BIF/20/6/6/...
935
80JM.BIF/20/4/6/...
1440
100JM.BIF/25/6/9/...
960
100JM.BIF/25/4/9/...
1470
JM AEROFOILBIFURCATED
180
V
160
Type D
15 140 83 85 120 82
0.6
0.5
100 84 80 80 82
84 10
0.4
0.3 85 60 82 84 83 40 24 81 20 8 0 0.0 0.30 0.25 0.20 0.15 0.10 0.05 0.00 0.0 0.2 0.4 8 0.6 16 0.8 1.0 1.2 1.4 1.6 24 32 40 0 0.0 16 0.1 32 40
0.2
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
Inlet Levels
Pitch Angle
8 63 12 16 13 11 6 7
Outlet Levels
Pitch
8k 27 23 29 21 21 24
Angle
8
16
16
24 40
24 40
SK10751
06/12/96
JM AEROFOILBIFURCATED
250
V
Type D
200
20
0.8
86 150 85 84 83 15 0.6
100 85
80 82
85
10
0.4
86 50 82 80 82 16 0 0.0 0.35 0.30 0.25 0.20 0.15 0.10 0.05 0.00 0.0 0.2 8 0.4 0.6 16 0.8 24 32 40 8 0.2 0.4 0.6 0.8 1.0 1.2 1.4 0 0.0 24 32 40 5 0.2
1.0
1.2
1.4
Inlet Levels
Pitch Angle
8 63 19 20 16 14 8 9
Outlet Levels
Pitch
8k 31 26 28 22 23 26
Angle
8
16
16
24 40
24 40
SK10752
06/12/96
JM AEROFOILBIFURCATED
V
Type D
2.5 60 99 100 98 50
600
500
2.0
300
101 97 100 32
30 40 1.0
200 98 24 96 16 8 0 0.0 2.5 2.0 1.5 1.0 0.5 0.0 0.0 16 1.5 2.0 24 8 0.5 1.0
20
0.5 10
100
0.5
1.0
1.5
2.0
2.5
3.0
0.0
40 32
2.5
3.0
Inlet Levels
Pitch Angle
8 63 16 17 16 12 7 8
Outlet Levels
Pitch
8k 22 18 23 18 19 21
Angle
8
16
16
24 40
24 40
SK10753
06/12/96
JM AEROFOILBIFURCATED
900
V
800
Type D
80 3.0
500
2.0
100 40
1.5
1.0
200
0.5
0.0
40 32 24
8 0.5 1.0
16 1.5
2.0
2.5
3.0
Inlet Levels
Pitch Angle
8 63 19 17 14 11 8 8
Outlet Levels
Pitch
8k 24 19 22 18 20 22
Angle
8
16
16
24 40
24 40
SK10754
06/12/96
JM AEROFOILBIFURCATED
V
Type D
250
25
1.0
200 91 88
88 20
0.8
89
24 5 0.2
50 86 16 8 0 0.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0.0 0.5 1.0 8 1.5 16 2.0 2.5 3.0 24 32 40
0.5
1.0
1.5
2.0
2.5
3.0
0.0
Inlet Levels
Pitch Angle
8 63 12 16 13 11 6 7
Outlet Levels
Pitch
8k 27 23 29 21 21 24
Angle
8
16
16
24 40
24 40
SK10755
06/12/96
JM AEROFOILBIFURCATED
350
V
Type D
300
30
1.2
250 89 90 92 200 91 91
25
1.0
20
0.8
91 100 88
32 24
10
86 50
88 16 8
0.2
0 0.0 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0.0
0.5
1.0
1.5
2.0
2.5
3.0
0.0
32
24 8 0.5 1.0 16
1.5
2.0
2.5
3.0
Inlet Levels
Pitch Angle
8 63 19 20 16 14 8 9
Outlet Levels
Pitch
8k 31 26 28 22 23 26
Angle
8
16
16
24 32
24 32
SK10756
06/12/96
JM AEROFOILBIFURCATED
1200
V
Type D
1000
100
106 600
105 101
104
60
107 400
2 40 32 40
103
106
104
24 20 16
200
102
8 0 0 0
5 40 32 24
7 6 5 4 3 2 1 0 0 1 2 8 3 16 4 5
Inlet Levels
Pitch Angle
63
Outlet Levels
Pitch
8k
Angle
63
125
250
SK10757
06/12/96
JM AEROFOILBIFURCATED
1400
V
Type D
5 120
1200
106 100
107
80 3
32 24
40
102
1 20
200
104 16 8
6 5 4 3 2 1 0 0 1 8 2 3 16 24 32
Inlet Levels
Pitch Angle
8 63 19 17 14 11 8 8
Outlet Levels
Pitch
8k 24 19 22 18 20 22
Angle
8
16
16
24 32
24 32
SK10758
06/12/96
JM AEROFOILBIFURCATED
200
V
Type D
0.7
88 88 84 10 83 89 87 84 32
100
0.4
0.3
50
83
24
0.2
84 16 0.1
8 0 0.0 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0.0 0.5 1.0 8 1.5 2.0 16 24 32 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 0 0.0
2.5
3.0
3.5
4.0
Inlet Levels
Pitch Angle
8 63 15 17 14 12 10 9
Outlet Levels
Pitch
8k 35 29 31 25 27 28
Angle
8
16
16
24 32
24 32
SK10759
06/12/96
JM AEROFOILBIFURCATED
500
V
Type D
400 97
40 1.5
93 100 94 16 8 0 0 1 2 3 4
24
0.0
Inlet Levels
Pitch Angle
8 63 19 18 17 14 12 11
Outlet Levels
Pitch
8k 31 25 29 23 25 25
Angle
8
16
16
24 32
24 32
SK10760
06/12/96
JM AEROFOILBIFURCATED
250
V
Type D
200 92 96 92 150
20
0.8
89
15
0.6
89
90 100
89
10 24
0.4
88
50
88
16
0.2
0.0
Inlet Levels
Pitch Angle
8 63 16 17 16 15 13 11
Outlet Levels
Pitch
8k 33 29 31 27 26 27
Angle
8
16
16
24 24
24 24
SK10761
06/12/96
JM AEROFOILBIFURCATED
600
V
Type D
500
50
2.0
400
300
99
30
100
99
1.0
200 98
24
20
98 100
16
0.5 10
10
12
0.0
4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 0 2 4 8 6 8 10 12 16 24
Inlet Levels
Pitch Angle
8 63 17 15 18 15 14 12
Outlet Levels
Pitch
8k 29 25 30 24 25 25
Angle
8
16
16
24 24
24 24
SK10762
06/12/96
JM AEROFOILBIFURCATED
350
V
Type D
300
30
1.2
25
1.0
200
101
20
0.8
16 5 8 0.2
50
10
12
14
16
0.0
6 5 4 3 2 1 0 0 2 4 8 6 8 16 24
10
12
14
16
Inlet Levels
Pitch Angle
8 63 23 21 19 14 14 11
Outlet Levels
Pitch
8k 28 23 29 27 25 26
Angle
8
16
16
24 30
24 30
SK11596
17/03/98
JM AEROFOILBIFURCATED
800
V
Type D
700
70
50
400 106
106
40 1.5 111
24
30 1.0
20
0.5 100 8 10
10
15
20
25
0.0
20 15 10 5 0 8 0 5 10 16 24
15
20
25
Inlet Levels
Pitch Angle
8 63 22 19 18 13 13 10
Outlet Levels
Pitch
8k 22 19 24 22 21 23
Angle
8
16
16
24 30
24 30
SK11597
17/03/98
FORM B ONL Y
Code
Motor
Weight (kg) 15 21 24 26 28
15JM.33 25JM.33
1.6 2 2 2 2
4 8 8 8 8
8 10 10 10 10
30JM.33
D63 D71
11
AIRFLOW
FORM B ONLY
B A
AIRFLOW
L crs. M
Slots in feet N
G D
Code
40JM.Bif
Motor
D71 F2225 D80
A
400 400 500 500 500
B
524 524 610 610 610
C
727 727 787 787 787
D
367 408 408
E
3 3 3 3 3
F
375 375 430
G
332 371 371
H
450 450 560 560 560
J
27 27 27
K
641 641 691 691 691
L
350 350 450 450 450
P
250 250 315 315 315
Q
3 3 3 3 3
S
8 8 12 12 12
T
12 12 12 12 12
Weight (kg) 61 72 78 83 93
50JM.Bif
F2225 F2229
63JM.Bif - 100JM.Bif
S No. of holes T on H P.C.D.
Hole J
A P
FORM B ONLY
L crs. M
Slots in feet N
K crs. C
AIRFLOW
Code
Motor
E
3 3 5 5 5
F
360 468 492 -
G
400 484
K
530 544 720 920 920
L
580 750
P
400 510 574 574 574
Q
3 5 6 6 6
690 27 860 27
630 10 800 10
12
Suitable for fan A 400 400 500 500 630 630 800 800 1000 1000
Type I IV I IV I IV I IV I IV
Weight (kg) 1.6 0.6 2.0 0.7 2.8 1.2 3.5 1.5 5.0 2.0
BELLMOUTH
Suitable for fan A 305 400 500 630 800 1000
Suitable for fan A
C 57 80 87 108 134
D Max.
Weight (kg)
167 1199
MATCHING FLANGE
D
FLEXIBLE CONNECTION
E
DAMPER
G F
25 25 25 32 32 50 50 50
135 135 162 110 225 17 110 225 75 160 225 176 160 225 270 160 225 345
10 16 20 27 36
13
C Length 1 2 184 273 305 400 610 800 350 450 560 690 860 M6 M8 M8 M10 M10 M10 M10
B A
305
POD - TYPE C ONLY
10 15 25 35 55 82
16 25 41 61 96
12 18 29 42 66 100
18 30 48 72 116
400 500
1200 1000
The above silencers give the approximate dB(A) reductions:B Type 1 diameter length - 7 to 10 dB(A) C Type 1 diameter length - 12 to 15 dB(A) For full acoustic details contact our Woods Acoustic Divsion Telephone: +44(0)1206 544122
2 holes G
F A
64 64 85 85 151 151
43 43 56 56 101 101
2 2 2 2 3 3
15 15 30 30 55 55
20 20 25 25 45 45
50 50 66 66 124 124
7 7 8 8 11.5 11.5
M6 M6 M8 M8 M10 M10
C E
OPEN SPRING
Type Rated Load (kg) 30 60
Base Deflection at Free Base Mounting rated load Height fixing fixing Screw centres (mm) hole (mm) (mm)
30 Yellow 60 Green
25 30
94 94
85 85
M8 M8
M10 M10
14
Woods Air Movement Limited is represented in over 70 countries world-wide. See our website for details - www.woods-fans.com
U.K.
England South & South East Woods Air Movement Limited Tufnell Way Colchester CO4 5AR Telephone: +44 (0)1206 544122 Facsimile: +44 (0)1206 574434 E-mail: enquiry@woods-fans.com Wales, Midlands & South West England Woods Air Movement Limited Waterlinks House, Richard Street Birmingham B7 4AA Telephone: +44 (0)121 359 6633 Facsimile: +44 (0)121 359 1818 E-mail: birmingham@woods-fans.com Scotland & North of England Woods Air Movement Limited P.O. Box 142 Manchester M60 1AQ Telephone: +44 (0)161 8480341 Facsimile: +44 (0)161 8729847 E-mail: manchester@woods-fans.com
Europe
Finland Woods Puhallin Oy Ruosilantie 2b 00390 Helsinki Finland Telephone: +35 8 9 540 4770 Facsimile: +35 8 9 540 47754 France Cie Franaise Woods 16 Burospace F91572 Bievres Cedex France Telephone: +33 1 6019 5594 Facsimile: +33 1 6019 5571 Germany Woods Ventilatoren GmbH Siemensstrasse 16 40 855 Ratingen Germany Telephone: +49 21 02 31068 Facsimile: +49 21 02 39113 Italy Woods Italiana SpA Via Montenero 55/57 20092 Cinisello Balsamo Milan, Italy Telephone: +39 02 61 86091 Facsimile: +39 02 61 860947
E-mail: info@woods-puhallin.fi
E-mail: woodsfr@gec-france.fr
E-mail: woods@t-online.de
E-mail: info@woods-italiana.it
International
Canada Woods Air Movement (Canada) Limited 401 Traders Blvd Unit #8, Mississauga Ontario L4Z 2H8 Canada Telephone: +1 905 501 0211 Facsimile: +1 905 501 0399 Singapore Woods Singapore Pte Marconi Building 3 Tai Seng Drive Singapore 535216 Telephone: +65 3828233 Facsimile: +65 3828200 USA American Fan Company 2933 Symmes Road Fairfield Ohio 45014, USA Telephone: +1 513 874 2400 Facsimile: +1 513 870 6249
E-mail: francis.tan@marconi.com.sg
E-mail: af-sales@amfan-woods.com
Due to a policy of continuous development and improvement the right is reserved to supply products which may differ from those illustrated and described in this publication. Certified dimensions will be supplied on request on receipt of order.
Copyright Woods Air Movement Limited. England 2000
Flkt Woods Group provides a full range of products and solutions for buildings ventilation, air treatment and industrial air movement
Head office
Flkt Woods Ltd Tufnell Way COLCHESTER, CO4 5AR United Kingdom Tel: +44 1206 544122 Fax: +44 1206 574434
Sales Offices available World Wide - See our website for details
www.flaktwoods.com
Due to a policy of continuous development and improvement the right is reserved to supply products which may differ from those illustrated and described in this publication. Certified dimensions will be supplied on request on receipt of order. Year 2000
DDJRG/JMBif