You are on page 1of 6

SECTION 08210 WOOD DOORS AND FRAMES PART 1 - GENERAL 1.1 SECTION INCLUDES A. 1.

2 Wood doors and frames as shown on the Drawings and as specified herein.

REFERENCES A. SASO Saudi Arabian Standards Organization SASO 815 SASO 1254 SASO 1256 B. Wooden Doors Methods of test for wooden windows and doors Specifications for timber

AWI - Architectural Woodwork Institute: AWI Architectural Woodwork Quality Standard Guide Specification and Certification Program

C.

NWMA - National Woodwork Manufacturers Association: IS.1 - Industry Standard for Flush Doors

D.

WIC - Woodwork Institute of California: WIC Manual of Millwork

E.

ASTM - American Society of Testing and Materials: ASTM E 152 - Fire Test of Door Assemblies

F.

NEMA - National Electrical Manufacturer's Association: LD 3 - High Pressure Decorative Laminates

G.

NFPA - National Fire Protection Association: NFPA 80 - Fire doors and Windows

1.3

SUBMITTALS A. Product Data: Submit door manufacturer's product data for each type of wood door, including details of core and edge construction, unless otherwise indicated.

B.

Samples: Submit samples of door faces representing typical range of color and grain, strips of solid wood of species to be used for exposed edges, trim and other
08210-1 Wood Doors And Frames

ITCC in Riyadh Residential Complex J10-13300

solid wood components. 1.4 TRANSPORTATION, HANDLING AND STORAGE A. Protect wood doors during transit, storage and handling to prevent damage, soiling and deterioration. Comply with requirements of referenced ANSI standards and recommendations of door manufacturer. Identify each door with individual opening numbers which correlate with designation system used on shop drawings for doors, frames and hardware, using temporary, removable or concealed markings.

B.

1.5

WARRANTY A. Door Manufacturer's Warranty: Submit two copies of written agreement in door manufacturer's standard form signed by the Manufacturer, Installer and Contractor, agreeing to repair or replace defective doors which have warped (bow, cup or twist) or which shows photographing of core construction below in face veneers, or do not conform to tolerance limitations of NWMA and AWI. The warranty shall also include refinishing and reinstallation that may be required due to repair or replacement of defective doors where defect was not apparent prior to hanging. Warranty shall be valid for a period of 1 year from the time of substantial completion.

B.

C.

PART 2 - PRODUCTS 2.1 WOOD DOORS - GENERAL A. Doors shall be fabricated meeting the applicable requirements of the quality standard of the Architectural Woodwork Institute. All fire rated doors shall be UL listed or equivalent and shall be labeled in factory indicating the fire rating. Door Size: Width, height and design shall be as shown on Drawings. Door shall be 44 mm thick, unless otherwise required by manufacturer or indicated on Drawings. Tolerances: Size, squareness and warp tolerances shall be in accordance with NWMA 1.S.1. Hardware: Conform to Section 08710 - DOOR HARDWARE. Prefit and premachine wood doors at factory complying with tolerance requirements of AWI for prefitting. Machine doors for hardware requiring cutting of doors. Comply with final hardware schedule and door frame shop drawings and with hardware templates and other essential information required to ensure proper fit of doors and hardware.

B. C. D. E.

F.

Wood used for doors and frames shall be approved by Engineer as well as the door construction and design.

ITCC in Riyadh Residential Complex J10-13300

08210-2

Wood Doors And Frames

2.2

SOLID WOOD PANEL DOORS A. Doors shall be constructed of best quality hardwood with a minimum thickness of 44 mm, unless otherwise required by door manufacturer or indicated on Drawings. 1. 2. Type of wood shall be as indicated on Drawings. Stiles, top and bottom rails, decorative panels and moldings, transoms, shall be of sizes and patterns as shown on Drawings and as approved by the Engineer.

B.

Door components shall be assembled using tongued and grooved connections as well as adhesive Type I and in accordance with the fabrication procedures mentioned below. 1. Where indicated on Drawings, provide carved panels. Submit various decorative designs for panels for the Engineer selection and approval.

C. 2.3

Solid wood panel doors shall include single swing and double swing as shown on Drawings.

SOLID-CORE WOOD DOORS A. General: 1. Doors for Transparent Finish: Comply with following requirements: a. b. c. 2. AWI Grade: Premium, with Grade AA faces. Faces: Type as indicated on Drawings. Finish: Doors and frames shall have natural lacquer finish.

Doors for Opaque Finish: Comply with following requirements: a. b. AWI Grade: Custom. Faces: Closed grain hardboard suitable for the intended application.

3. B.

Stiles and Rails: 44 mm Solid hardwood.

Solid-Core doors: 1. Particleboard Cores: Comply with the following requirements: a. b. Particleboard Cores: Single thickness 3-ply conforming to ANSI A208.1, Grade LD-1. Blocking: Provide wood blocking at particleboard-core doors as follows: 1.) 2.) 125 mm top-rail blocking, at doors indicated to have closers. 125 mm bottom-rail blocking, at doors indicated to have kick, mop or armor plates.
08210-3 Wood Doors And Frames

ITCC in Riyadh Residential Complex J10-13300

3.) 2.

125 mm midrail blocking, at doors indicated to have exit devices.

Interior Veneer-Faced Doors: a. b. Core: Particleboard core. Construction: 7-Plies construction with stiles and rails bonded to core, then entire unit abrasive planed before veneering.

3.

Interior Hardboard-Faced Doors: a. b. Core: Particleboard core. Construction: hardboard faces glued directly to core with stiles and rails bonded to core, then entire unit abrasive planed before faces are applied.

2.4

HOLLOW-CORE FLUSH WOOD DOORS A. General: 1. Doors for Transparent Finish: Comply with following requirements: a. b. c. 2. AWI Grade: Premium, with Grade AA faces. Faces: Type as indicated on Drawings. Finish: Doors and frames shall have natural lacquer finish.

Doors for Opaque Finish: Comply with following requirements: a. b. AWI Grade: Custom. Faces: Closed grain hardboard suitable for the intended application.

3. B.

Stiles and Rails: 44 mm Solid hardwood.

Hollow-Core Flush Doors: 1. Interior Veneer-Faced Doors: a. b. c. Core: Corrugated expandable honeycomb core complying with ANSI Section 1300/NWWDA I.S.1. Construction: 7-Plies. Blocking: Provide wood blocking with minimum dimensions as follows: 1.) 2.) 250 mm bottom-rail blocking. 125-by-460 mm lock blocks.

ITCC in Riyadh Residential Complex J10-13300

08210-4

Wood Doors And Frames

3.) C. Fire-rated Doors: 1. 2.

46 mm midrail blocking.

Construction: Manufacturer standard mineral-core construction as required to provide fire rating indicated. Blocking: Provide composite blocking with improved screw-holding capability approved for use in doors or fire ratings indicated and as necessary to eliminate need for through-bolting hardware. Edge Construction: At hinge stiles, provide manufacturer standard laminated-edge construction with improved screw-holding capability and split resistance and with outer stile matching face veneer. Pairs: Furnish formed-steel edges and astragals for pairs of fire-rated doors, unless otherwise indicated.

3.

4. 2.5

DOOR FRAMES A. Door Frame Type: As indicated on Drawings and in accordance with the following requirements: 1. Solid Wood Frames: a. Type of Wood: Use rigid, square and uniform, best quality solid hardwood, architectural grade, clear all heart. Type of wood shall be as indicated on Drawings. Wood used shall be of a species listed as suitable for door frames and shall match with type specified for the related wood door. Frame Sizes, Rebates and Shapes: As shown on Drawings and as approved by Engineer. Frame rebates shall be 13 mm minimum depth for the internal doors and 19 mm for the external doors. Frames shall have wood architraves as shown on Drawings.

b. c.

2.

Metal Door Frames: Manufacturer standard steel door frames complying with the requirements specified in Section 08100 - HOLLOW METAL DOORS AND FRAMES.

2.6

FABRICATION A. Openings: Where indicated, cut and trim openings through doors and panels complying with the applicable requirements of referenced standards for the kind of doors required. Exterior Doors: Treat exterior doors at factory with water repellent after manufacturing has been completed. Assembly: Assemble solid paneled doors and frames using be tongued and
08210-5 Wood Doors And Frames

B. C.

ITCC in Riyadh Residential Complex J10-13300

grooved connections with Type I waterproof adhesive. D. E. 2.7 FINISH A. Doors and Frames Finish: As indicated on Drawings and in accordance with the following requirements: 1. PART 3 - EXECUTION 3.1 INSTALLATION A. B. Each door unit shall be installed in accordance with the manufacturer's instructions including handling and storage recommendations. Doors shall be fitted to the following tolerances: 1. 2. 3. C. 3.18 mm on each vertical side and top. 13 mm on bottom, except when fitted hardware requires otherwise. Bevel non-rated doors 3.18 mm in 50 mm at lock and hinge edges. Veneers: Natural lacquer finish. Adhesives: Assemble doors using Type I waterproof adhesives. Factory-Finishing: Provide manufacturer's standard finish to match approved sample.

Install finish hardware to the templates provided. Fit to frames and machine for hardware to whatever extent not previously worked at factory as required for fit and uniform clearance at each edge. Restore finish on edges of shop-finished doors before installation, if fitting or machining is required at the job site.

D. 3.2

ADJUST AND CLEAN A. Operation: Rehang or replace doors which do not swing or operate freely, as directed by the Engineer. Finished Doors: Refinish or replace doors damaged during installation as directed by the Engineer. Institute protective measures as recommended and accepted by door manufacturer to assure that wood doors will be without damage or deterioration at time of substantial completion. END OF SECTION

B. C.

ITCC in Riyadh Residential Complex J10-13300

08210-6

Wood Doors And Frames

You might also like