Professional Documents
Culture Documents
Preparation
1. Make sure all data in re-homing design from Engineering team 2. Make sure channel team already update the new CGI in their system 3. Make sure transmission team already defined the IP and VID from rehoming design in router and MLTN side 4. Create and load IuB script in target RNC Parameter that will be changed in Iub Script: Iub link ID and Rbs ID IpAccessHostPool naming Based on RNC information (running command: get IpAccessHostPool in target RNC) remoteCpIpAddress1 IP Iub Iub userlabel
5. Doing health check all Node and RNC that will be re-homed 6. Make CV backup for all Node and RNC that will be re-homed 7. Backup old data in source RNC with simulation mode us+ <file name> rdel <Iub> usu! <file name> 8. Define New CGI in MSS side
II.
get 10 acl 10 acc 10 removeSyncRefResource answer y select the LDN: IpSystem=1,IpAccessHostEt=1,IpSyncRef=1 and for the next process select LDN:IpSystem=1,IpAccessHostEt=1,IpSyncRef=2 2. Create File for undo script U+ <File Name> 3. Lock IpSyncRef and IpAccessHostEt lst IpAccessHostEt get the proxy number of MO bl <proxy number1> <proxy number2> <proxy number3> 4. Delete IpSyncRef lst IpSyncRef get the proxy number of MO del <proxy number1> <proxy number2> 5. Delete Iub link lpr iub get the proxy number of MO related to Iub del <proxy number1> <proxy number2> <proxy number3> <proxy number4> Delete the proxy number from bottom to up except for this MO SwManagement=1,Repertoire=RBS_AIUB 6. Delete SCTP lst sctp get the proxy number of MO related to Iub del <proxy number1> <proxy number2> delete the proxy number from up to bottom 7. Delete IpAccessHostEt lst IpAccessHostEt get the proxy number of MO del <proxy number> 8. Delete Ip Interface for Iub get ipin get the proxy number of MO
del <proxy number> Make sure only delete ip interface for Iub (not for OAM) 9. Close file for undo script and convert to *.mo uu! <file name> 10.Edit the undo script Parameters that will be change: Default router for Ip Interfaces 1 (defaultRouter0) change with VIP value in design Gateway Iub. Vlan ID (vid Integer) IpAccessHostEt (IP Address IuB) Iub & rbsId IpSyncRef 1 and IpSyncRef 2 get the data from target RNC get IpAccessHostEt (in target RNC) looking for IpAccessHost ET for Iub services (usually there are 2 in every subrack, slot 4 and slot 25, use slot 4 for IpSyncRef 1 and slot 25 for IpSyncRef 2) Lk iublink (in target RNC) get IpAccessHostEt.
NB: - The value of nthreshold parameter must be less than mbuffer heartbeatInterval Integer 10
11.Load the undo edit script trun <file name> 12.Add IpSyncRef 1 and IpSyncRef 2 as SyncReference acl 10 acc 10 addSyncRefResource answer y select the LDN: IpSystem=1,IpAccessHostEt=1,IpSyncRef=1, priority 1 and for the next process select LDN:IpSystem=1,IpAccessHostEt=1,IpSyncRef=2, priority 2
14.Check the status for IpAccessHostEt and IpSyncRef lst IpAccessHostEt The status must be enabled 15.Make a backup CV for new configuration cvms <cv name> <creator> <comment> cvrbset <cv name> 16.Restart Node B (if needed)
II.2 Moving Utrancell use RTR Tools (Refer to MOP using RTR Tools)