You are on page 1of 16

Tutorial on Screw Jack

Hareesha N G Asst. Professor Dept of Aeronautical Engg Dayananda Sagar College of Engg Bangalore-78

3/26/2013

Hareesha N Gowda, DSCE, Blore-78

Assembly Drawings
1. Screw Jack

3/26/2013

Hareesha N Gowda, DSCE, Blore-78

Part-1: Create body of the Screw jack 1. Select XZ Plane 2. Draw the 2D sketch as shown 3. Use revolved protrusion command to create 3D feature, Angle 3600

3/26/2013

Hareesha N Gowda, DSCE, Blore-78

Part-1: Create body of the Screw jack Create fillets as shown in Fig. 1, 2, and 3

3/26/2013

Hareesha N Gowda, DSCE, Blore-78

Part-2: Create nut of the screw jack 1. Select XZ Plane 2. Draw the 2D sketch as shown in Fig.1 3. Use revolved protrusion command to create 3D feature, Angle 3600 as shown in fig.2 4. Create threaded hole as shown in Fig.4 using Fig.3

Fig.2 Fig.1

Fig.3

Fig.4
3/26/2013 Hareesha N Gowda, DSCE, Blore-78 5

Part-3: Create Screw Spindle of the screw jack (Step-1) 1. Select XZ Plane 2. Draw the 2D sketch as shown in Fig.1 3. Use revolved protrusion command to create 3D feature, Angle 3600 as shown in Fig.2

Fig.2 Fig.1
3/26/2013 Hareesha N Gowda, DSCE, Blore-78 6

Part-3: Create Screw Spindle of the screw jack ( Step-2) 1. Select XZ Plane 2. Draw the 2D sketch as shown 3. Use Cut out command to create Symmetric through hole

3/26/2013

Hareesha N Gowda, DSCE, Blore-78

Part-3: Create Screw Spindle of the screw jack ( Step-3) 1. Select XY Plane 2. Draw the 2D sketch as shown 3. Use Cut out command to create Symmetric through hole

3/26/2013

Hareesha N Gowda, DSCE, Blore-78

Part-3: Create Screw Spindle of the screw jack ( Step-4) 1. Select the Plane as shown, use threaded hole command, Go to hole option, set the parameters as shown in dialogue box and create threaded hole as shown in fig.1

fig.1

3/26/2013

Hareesha N Gowda, DSCE, Blore-78

Part-4: Create CUP of the screw jack (Step-1) 1. Select XZ Plane 2. Draw the 2D sketch as shown 3. Use revolved protrusion command to create 3D feature, angle 3600

3/26/2013

Hareesha N Gowda, DSCE, Blore-78

10

Part-4: Create CUP of the screw jack (Step-2) 1. Select XZ Plane 2. Draw the 2D sketch as shown 3. Use Cut out command to create the profile as shown 4. Use Circular pattern to create remaining features as shown

3/26/2013

Hareesha N Gowda, DSCE, Blore-78

11

Part-5: Create Special washer of the screw jack 1. Select XZ Plane 2. Draw the 2D sketch as shown 3. Use revolved protrusion command to create 3D feature, angle 3600

3/26/2013

Hareesha N Gowda, DSCE, Blore-78

12

Part-6: Create Special washer of the screw jack (Step-1) 1. Select XZ Plane 2. Draw the 2D sketch as shown 3. Use revolved protrusion command to create 3D feature, angle 3600

3/26/2013

Hareesha N Gowda, DSCE, Blore-78

13

Part-6: Create Special washer of the screw jack (Step-2) 1. Select top surface as shown 2. Draw the 2D sketch as shown 3. Use cut out command to create 3D feature, depth 3mm

3/26/2013

Hareesha N Gowda, DSCE, Blore-78

14

Part-6: Create Special washer of the screw jack (Step-3) 1. Select cylindrical surface as shown 2. Use thread command to create thread feature with the parameters as shown below

3/26/2013

Hareesha N Gowda, DSCE, Blore-78

15

Part-7: Create Tommy Bar of the screw jack Select XZ Plane Draw the 2D sketch as shown Use revolved protrusion command to create 3D feature, angle 3600

3/26/2013

Hareesha N Gowda, DSCE, Blore-78

16

You might also like