Professional Documents
Culture Documents
Hareesha N G Assistant Professor Dept of Aeronautical Engg Dayananda Sagar College of Engg Bangalore-78
4/9/2013
2.Plummer Block
4/9/2013
Part 1: Body: 1. Create the sketch as shown in figure 2. Use Protrusion command to create the 3D feature, width 36 mm
3. Use mirror copy feature (smart option), mirror other side of the body Select feature Right click to accept Select mirror plane Finish
4/9/2013
4/9/2013
Part 1: Body: 1. Select top surface plane, 2. Create the sketch on top face of the body as shown in figure 3. Use cutout command to create the 3D feature shown in figure, show outside cutout while creating cutout. 4. Use from/ to option, select top and bottom surface of the body
4/9/2013
Part 1: Body: 1. Select bottom plane, Create the sketch by selecting bottom face as shown in figure 3. Use cut out, depth 2 mm.
4/9/2013
Part 1: Body: 1. Select bottom plane, 2. Create the sketch by selecting bottom face as shown in figure 3. Use cut out command to create the 3D feature, depth through all.
4/9/2013
Part 1: Body: Use mirror copy feature (smart option), mirror all features to other side of the body Select all features to be mirrored (Hold Ctrl Key and edge bar to select) Right click to accept Select mirror plane Finish
4/9/2013
Part 1: Body: 1. Select top surface 2. Use hole command to create the 3D feature shown in figure using parameters shown
4/9/2013
Part 2: cup: 1. Select YZ plane, 2. Crete the sketch as shown in figure 3. Use protrusion command to create the 3D feature, width 36 mm
4/9/2013
10
Part 2: cup: 1. Select top surfece 2. Crete the sketch as shown in figure 3. Use cutout command to create the 3D feature shown in figure, show outside cutout while using the command
4/9/2013
11
Part 2: cup: 1. Select top surface 2. Crete the sketch as shown in figure 3. Use cutout command to create the 3D feature shown in figure
4/9/2013
12
Part 2: cup: 1. Create a plane tangent to top surface 2. Hole command to create the 3D feature shown in figure using parameters defined
4/9/2013
13
Part 3: Bottom half bearing 1. Select YZ plane, 2. Crete the sketch as shown in figure 3. Use revolved protrusion command to create the 3D feature shown in figure, use 180o
4/9/2013
14
Part 3: Bottom half bearing 1. Select YZ plane, 2. Crete the sketch as shown in figure 3. Use revolved protrusion command to create the 3D feature shown in figure, revolution 180o
4/9/2013
15
Part 3: Bottom half bearing 1. Select left surface 2. Crete the sketch as shown in figure 3. Use cutout command to create the 3D feature shown in figure
4/9/2013
16
Part 4: Bearing top half 1. Save the previous part (part.3- Bottom half) file as Bearing top half 2. Delete unwanted, create hole as shown.
4/9/2013
17
Part - 5: Bolt M10 1. Select top plane, create sketch as shown in fig. 2. Select xz plane, create sketch as shown, use revolved cut out to create bolt chamfer as shown.
4/9/2013
18
Part 6: Nut M10 1. Select top plane 2. Crete the sketch as shown in figure 3. Use symmetric protrusion command, height-8mm to create features as shown in figure. Create threaded hole as shown.
4. Select XZ plane, create sketch as shown in fig. use revolved cutout (outside cut) to create features as shown in figure. Mirror to other side.
4/9/2013
19
Part 7: Lock Nut M10 Save the previous file( M10 Nut) as lock Nut M10, change the protrusion height to 5mm.
4/9/2013
20
4/9/2013
21