Professional Documents
Culture Documents
TEMPERATURE SETTING.
HP57 Press TEMP key (key lamp flashes):
This message will be displayed instead of the
°C Set Temperature value.
Press + or - to modify. Press TEMP to confirm.
Example SEt.t = 20.0°
HUMIDITY SETTING.
Press HUM key (key lamp flashes):
This message will be displayed instead of the
% Rh Humidity value.
DEHUM OUTPUT
TEMPERATURE
HEAT OUTPUT
COOL OUTPUT
HUM OUTPUT
SEt.H = 80.0H
PROBE SX
Example
PROBE *2
HUMIDITY
diF.t 0.2° °C temperature differential *1) temperature difference between dry 0,0°C 1,0°C 2,1°C 3,3°C 4,4°C 5,7°C 0°C
CYC.t 0.0" Temperature regulation cycle time in seconds *1) It is supposed that water of wet bulb is 0,0°C 3,0°C 6,1°C 10,0°C 14,4°C 19,6°C 30°C
diF.H 1.0% °C Humidity differential *1) pure, temperature probes are not 0,0°C 3,5°C 7,0°C 12,0°C 18,2°C 25,6°C 40°C
0,0°C 4,0°C 8,2°C 14.0°C 21,8°C 32,2°C 50°C
rEL.H 0.0% %Rh setting shift reffering to Set.H *1) irradiated by light and are located in a 0,0°C 6,5°C 9,8°C 16,3°C 24,5°C 38,0°C 60°C
CYC.H 0.0" Humidity regulation cycle time in seconds *1) moved-air duct. 0,0°C 6,8°C 11,8°C 18,4°C 27,0°C 46,0°C 70°C
tEnP =1 Temperature representation (=1 °C, =2 °F) Data are linear-interpolated by HP57 0,0°C 7,0°C 12,6°C 21,6°C 31,7°C 52,5°C 80°C
0,0°C 7,5°C 13,3°C 23,3°C 35,8°C 60,5°C 90°C
Huny =0 Humidity sensor type (0= psycrom etric, 1= 4-20mA) *2) with 1/256 math precision degree. 0,0°C 8,3°C 16,3°C 26,8°C 38,3°C 68,2°C 100°C
*3) You can correct the readings on the various sensors (+ or -). E ON ON 75%
R HEAT
TU
CYC.t
HEAT A ON ON 50%
R
PE
CYC.t
ON ON 25%
PRESET PROGRAMS (Bootstrap)
1/2 diF.t 1/2 diF.t
M
OFF TE OFF 0%
OFF
At delivery this processor is ready programmed with the following (variable) *1 Relay's operating computed
CYC.H
"HAND" MODE ON ON 75%
CYC.H
HUM
In some start-up conditions may be useful to work in "hand" mode: HUM
I TY ON ON 50%
Power off the processor, press + key and keep it pressed giving power on: ID CYC.H
M ON ON 25%
Hand message will be displayed (release now + key). 1/2 diF.H 1/2 diF.H
U
H OFF
Push + until is displayed number required to be handed (see table State OFF OFF 0%
*1 Relay's operating computed
indication lamps and push HUM for activating relay. with 1% resolution and
Set.H + rEL.H actioned minimum 0,5 sec. Set.H + rEL.H
Pushing again + for increase relay number previous relay is disactivated. HUMIDITY HUMIDITY
You can press HUM for a least two seconds to escape and return to the Run Mode.